text string | label int64 |
|---|---|
Grease the fasteners. | 0 |
Apply grease to the fasteners. | 1 |
No leaks permitted. | 0 |
Make sure that there are no leaks. | 1 |
Follow the safety instructions. | 0 |
Obey the safety instructions. | 1 |
Test the system for leaks. | 0 |
Do the leak test of the system. | 1 |
Test the system for leaks. | 0 |
Do a test for leaks in the system. | 1 |
Dim the lights. | 0 |
The lights become dim. | 1 |
A value of 2mm is acceptable. | 0 |
A value of 2mm is permitted. | 1 |
Make sure that the valve is operable. | 0 |
Make sure that the valve can operate. | 1 |
Make sure that the two spigots at the base of the unit engage. | 0 |
Make sure that the two spigots at the bottom of the unit engage. | 1 |
For this procedure, make sure that one person is available as backup. | 0 |
Two persons are necessary to do this procedure. | 1 |
The laptop has these main parts: | 0 |
The laptop has these primary parts: | 1 |
Oil the steel surfaces. | 0 |
Apply oil to the steel surfaces. | 1 |
If you think it will snow, make sure that the vehicle is in the applicable position. | 0 |
If you think that snow will fall, make sure that the vahicle is in the applicable configuration. | 1 |
Remove the four stainless steel pan head machine screws (10) that attach the metallic machine flange (15) to the front housing cover (20). | 0 |
Remove the four screws (10) that attach the flange (15) to the cover (20). | 1 |
Make a sandwich with two washers and the spacer. | 0 |
Install the spacer between the two washers. | 1 |
Use a foot-long breaker bar during this procedure. | 0 |
Use a 12-inch wrench handle during this procedure. | 1 |
If you detect broken wires, repair them. | 0 |
If you find broken wires, repair them. | 1 |
Machine the hole until it has a diameter of 8.00 +/- 0.003mm. | 0 |
Ream the hole until it has a diameter of 8.00 +/- 0.003mm. | 1 |
Clamp the cable in position. | 0 |
Put clamps on the cable to hold it in position. | 1 |
Wire the cable to the structure. | 0 |
Attach the cable to the structure with wire. | 1 |
Do not enter the engine test area without approval. | 0 |
Do not go into the engine test area without approval. | 1 |
If the instrument fails to respond, do a test. | 0 |
If the instrument does not operate correctly, do a test. | 1 |
Give the hole a 0.20-inch over-ream. | 0 |
Ream the hole 0.20 inch larger than the standard. | 1 |
The door is made of carbon fibre reinforced plastic. | 0 |
The door is made of carbon fiber reinforced plastic. | 1 |
Change the colour of the display. | 0 |
Change the color of the display. | 1 |
Runway light connection resistance calibration. | 0 |
Calibration of the resistance of the runway light connection. | 1 |
Install the forward turbine overheat thermocouple terminal tags. | 0 |
Install the terminal tage on the forward overheat thermocouple of the turbine. | 1 |
Remove the engine transmission housing attachment bolts. | 0 |
Remove the bolts that attach the transmission housing to the engine. | 1 |
Adjust to obtain door operating rod alignment with the attachment point. | 0 |
Adjust the door operating rod until it aligns with the attachment point. | 1 |
Main-gear-door-retraction-winch handle. | 0 |
Main-gear-door retraction-winch handle. | 1 |
Turn shaft assembly. | 0 |
Turn the shaft assembly. | 1 |
Data module tells you how to operate unit. | 0 |
This data module tells you how to operate the unit. | 1 |
Tag the circuit breaker 36L7. | 0 |
Tag circuit breaker 36L7. | 1 |
The operator has adjusted the linkage. | 0 |
The operator adjusted the linkage. | 1 |
The volume control can be adjusted. | 0 |
You can adjust the volume control. | 1 |
The temperature must be adjusted. | 0 |
Adjust the temperature. | 1 |
The sleeve will be adjusted. | 0 |
You will adjust the sleeve. | 1 |
The seat is to be installed before you install the cushion. | 0 |
Install the seat before you install the cushion. | 1 |
When you are doing this procedure, obey all safety precautions. | 0 |
When you do this procedure, obey all the safety precautions. | 1 |
The circuits are connected by a switching relay. | 0 |
A switching relay connects the circuits. | 1 |
These values are used by the computer to calculate the energy consumption. | 0 |
The computer calculates the energy consumption from these values. | 1 |
The test can be continued by the operator. | 0 |
Continue the test. | 1 |
Oil and grease are to be removed with a degreasing agent. | 0 |
Remove the oil and grease with a degreasing agent. | 1 |
On the ground, the valve can be opened with the override handle. | 0 |
On the ground, you can open the valve with the override handle. | 1 |
Additives are not used in this product. | 0 |
We do not use additives in this product. | 1 |
Additives are not used in this product. | 0 |
This product does not contain additives. | 1 |
The ohmmeter gives an indication of 450 ohms. | 0 |
The ohmmeter shows 450 ohms. | 1 |
Check the laptop battery. | 0 |
Do a check of the laptop battery. | 1 |
The side stay assembly has two folding toggles hinged together and attached with hinges between the main gear strut and the side stay bracket. | 0 |
The side stay assembly has two folding toggles. The folding toggles are attached together with hinges. These toggles are also attached with hinges between the main gear strut and the side stay bracket. | 1 |
Different temperatures will change the cure time. | 0 |
Increase the temperature to decrease the cure time. | 1 |
End of preview. Expand in Data Studio
No dataset card yet
- Downloads last month
- 2