id
stringlengths 11
11
| image
stringlengths 22
22
| conversations
listlengths 2
2
|
|---|---|---|
Shaft_00857
|
images/Shaft_00857.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø58.1 mm and length at least 169.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø56.1 mm over length 61.1 mm (from Z=0.0 to Z=61.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø56.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø51.3 mm over length 14.3 mm (from Z=0.0 to Z=103.7).\n9. Finish turn diameter Ø39.1 mm over length 43.2 mm (from Z=0.0 to Z=89.4).\n10. Finish turn diameter Ø32.7 mm over length 46.2 mm (from Z=0.0 to Z=46.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00009
|
images/Shaft_00009.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø74.8 mm and length at least 257.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.8 mm over length 35.5 mm (from Z=0.0 to Z=35.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø66.3 mm over length 75.0 mm (from Z=0.0 to Z=216.8).\n10. Finish turn diameter Ø47.7 mm over length 57.3 mm (from Z=0.0 to Z=141.8).\n11. Finish turn diameter Ø32.2 mm over length 84.5 mm (from Z=0.0 to Z=84.5).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00074
|
images/Shaft_00074.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø61.0 mm and length at least 261.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø59.0 mm over length 73.4 mm (from Z=0.0 to Z=73.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø59.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø51.0 mm over length 85.5 mm (from Z=0.0 to Z=182.7).\n10. Finish turn diameter Ø46.0 mm over length 80.1 mm (from Z=0.0 to Z=97.2).\n11. Finish turn diameter Ø41.4 mm over length 17.1 mm (from Z=0.0 to Z=17.1).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00951
|
images/Shaft_00951.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø55.0 mm and length at least 243.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.0 mm over length 39.4 mm (from Z=0.0 to Z=39.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø35.0 mm over length 62.5 mm (from Z=0.0 to Z=199.4).\n10. Finish turn diameter Ø30.0 mm over length 136.9 mm (from Z=0.0 to Z=136.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00468
|
images/Shaft_00468.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 153.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 115.9 mm (from Z=0.0 to Z=115.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø29.0 mm over length 32.9 mm (from Z=0.0 to Z=32.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00307
|
images/Shaft_00307.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø69.3 mm and length at least 249.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.3 mm over length 52.3 mm (from Z=0.0 to Z=52.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø57.9 mm over length 15.6 mm (from Z=0.0 to Z=191.8).\n10. Finish turn diameter Ø41.9 mm over length 55.4 mm (from Z=0.0 to Z=176.2).\n11. Finish turn diameter Ø34.8 mm over length 16.8 mm (from Z=0.0 to Z=120.8).\n12. Finish turn diameter Ø30.1 mm over length 31.5 mm (from Z=0.0 to Z=104.0).\n13. Finish turn diameter Ø30.0 mm over length 72.5 mm (from Z=0.0 to Z=72.5).\n14. Break all edges (e.g., 2×45° where applicable).\n15. Remove the workpiece from the lathe."
}
] |
Shaft_00134
|
images/Shaft_00134.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø75.1 mm and length at least 292.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.1 mm over length 118.0 mm (from Z=0.0 to Z=118.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø70.0 mm over length 56.3 mm (from Z=0.0 to Z=169.7).\n10. Finish turn diameter Ø66.9 mm over length 81.7 mm (from Z=0.0 to Z=113.4).\n11. Finish turn diameter Ø54.0 mm over length 31.7 mm (from Z=0.0 to Z=31.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00859
|
images/Shaft_00859.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø54.7 mm and length at least 246.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø52.7 mm over length 16.2 mm (from Z=0.0 to Z=16.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø52.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø43.7 mm over length 37.7 mm (from Z=0.0 to Z=225.7).\n10. Finish turn diameter Ø30.0 mm over length 188.0 mm (from Z=0.0 to Z=188.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00884
|
images/Shaft_00884.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø44.1 mm and length at least 269.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø42.1 mm over length 105.3 mm (from Z=0.0 to Z=105.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø42.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 159.2 mm (from Z=0.0 to Z=159.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00244
|
images/Shaft_00244.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø66.7 mm and length at least 66.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø64.7 mm over length 12.3 mm (from Z=0.0 to Z=12.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø64.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø57.6 mm over length 8.8 mm (from Z=0.0 to Z=48.8).\n9. Finish turn diameter Ø39.8 mm over length 15.3 mm (from Z=0.0 to Z=40.0).\n10. Finish turn diameter Ø34.4 mm over length 7.4 mm (from Z=0.0 to Z=24.7).\n11. Finish turn diameter Ø30.0 mm over length 17.3 mm (from Z=0.0 to Z=17.3).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00641
|
images/Shaft_00641.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø37.4 mm and length at least 130.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø35.4 mm over length 22.4 mm (from Z=0.0 to Z=22.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø35.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 102.7 mm (from Z=0.0 to Z=102.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00209
|
images/Shaft_00209.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø65.9 mm and length at least 122.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.9 mm over length 45.6 mm (from Z=0.0 to Z=45.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø51.4 mm over length 55.5 mm (from Z=0.0 to Z=72.3).\n9. Finish turn diameter Ø32.7 mm over length 16.8 mm (from Z=0.0 to Z=16.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00267
|
images/Shaft_00267.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø68.5 mm and length at least 152.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø66.5 mm over length 25.6 mm (from Z=0.0 to Z=25.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø66.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø46.8 mm over length 39.9 mm (from Z=0.0 to Z=121.7).\n9. Finish turn diameter Ø38.2 mm over length 8.2 mm (from Z=0.0 to Z=81.8).\n10. Finish turn diameter Ø30.0 mm over length 73.6 mm (from Z=0.0 to Z=73.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00870
|
images/Shaft_00870.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø59.2 mm and length at least 88.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.2 mm over length 10.9 mm (from Z=0.0 to Z=10.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø46.7 mm over length 28.2 mm (from Z=0.0 to Z=72.8).\n9. Finish turn diameter Ø37.0 mm over length 44.6 mm (from Z=0.0 to Z=44.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00535
|
images/Shaft_00535.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø44.4 mm and length at least 85.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø42.4 mm over length 41.5 mm (from Z=0.0 to Z=41.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø42.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø38.8 mm over length 27.8 mm (from Z=0.0 to Z=38.9).\n9. Finish turn diameter Ø30.0 mm over length 11.1 mm (from Z=0.0 to Z=11.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00578
|
images/Shaft_00578.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø80.9 mm and length at least 216.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.9 mm over length 44.1 mm (from Z=0.0 to Z=44.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø64.7 mm over length 39.4 mm (from Z=0.0 to Z=167.3).\n10. Finish turn diameter Ø44.8 mm over length 16.1 mm (from Z=0.0 to Z=127.9).\n11. Finish turn diameter Ø30.0 mm over length 111.8 mm (from Z=0.0 to Z=111.8).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00845
|
images/Shaft_00845.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 185.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 134.9 mm (from Z=0.0 to Z=134.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø28.9 mm over length 45.6 mm (from Z=0.0 to Z=45.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00968
|
images/Shaft_00968.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø44.4 mm and length at least 91.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø42.4 mm over length 5.2 mm (from Z=0.0 to Z=5.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø42.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.3 mm over length 15.8 mm (from Z=0.0 to Z=81.3).\n9. Finish turn diameter Ø30.0 mm over length 65.5 mm (from Z=0.0 to Z=65.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00083
|
images/Shaft_00083.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø75.7 mm and length at least 77.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.7 mm over length 10.4 mm (from Z=0.0 to Z=10.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø56.5 mm over length 19.6 mm (from Z=0.0 to Z=61.8).\n9. Finish turn diameter Ø47.4 mm over length 26.1 mm (from Z=0.0 to Z=42.2).\n10. Finish turn diameter Ø30.0 mm over length 16.1 mm (from Z=0.0 to Z=16.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00040
|
images/Shaft_00040.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø66.0 mm and length at least 255.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø64.0 mm over length 45.9 mm (from Z=0.0 to Z=45.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø64.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø58.5 mm over length 67.3 mm (from Z=0.0 to Z=204.8).\n10. Finish turn diameter Ø39.2 mm over length 86.2 mm (from Z=0.0 to Z=137.5).\n11. Finish turn diameter Ø30.0 mm over length 51.3 mm (from Z=0.0 to Z=51.3).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00608
|
images/Shaft_00608.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø65.2 mm and length at least 200.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.2 mm over length 38.7 mm (from Z=0.0 to Z=38.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø55.4 mm over length 33.3 mm (from Z=0.0 to Z=156.6).\n10. Finish turn diameter Ø40.7 mm over length 47.6 mm (from Z=0.0 to Z=123.3).\n11. Finish turn diameter Ø30.0 mm over length 75.7 mm (from Z=0.0 to Z=75.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00592
|
images/Shaft_00592.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø50.7 mm and length at least 159.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø48.7 mm over length 53.3 mm (from Z=0.0 to Z=53.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø48.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø31.3 mm over length 55.4 mm (from Z=0.0 to Z=100.7).\n9. Finish turn diameter Ø30.0 mm over length 45.3 mm (from Z=0.0 to Z=45.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00853
|
images/Shaft_00853.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 279.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 221.4 mm (from Z=0.0 to Z=221.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø24.0 mm over length 52.6 mm (from Z=0.0 to Z=52.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00583
|
images/Shaft_00583.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø57.4 mm and length at least 74.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø55.4 mm over length 5.9 mm (from Z=0.0 to Z=5.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø55.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø52.3 mm over length 6.4 mm (from Z=0.0 to Z=63.2).\n9. Finish turn diameter Ø44.0 mm over length 5.7 mm (from Z=0.0 to Z=56.8).\n10. Finish turn diameter Ø40.1 mm over length 18.5 mm (from Z=0.0 to Z=51.1).\n11. Finish turn diameter Ø30.6 mm over length 20.1 mm (from Z=0.0 to Z=32.6).\n12. Finish turn diameter Ø30.0 mm over length 12.5 mm (from Z=0.0 to Z=12.5).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00122
|
images/Shaft_00122.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø59.2 mm and length at least 138.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.2 mm over length 30.9 mm (from Z=0.0 to Z=30.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø39.8 mm over length 29.1 mm (from Z=0.0 to Z=102.6).\n9. Finish turn diameter Ø30.6 mm over length 25.0 mm (from Z=0.0 to Z=73.5).\n10. Finish turn diameter Ø30.0 mm over length 48.5 mm (from Z=0.0 to Z=48.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00413
|
images/Shaft_00413.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø50.6 mm and length at least 97.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø48.6 mm over length 16.0 mm (from Z=0.0 to Z=16.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø48.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø37.6 mm over length 31.3 mm (from Z=0.0 to Z=76.2).\n9. Finish turn diameter Ø34.3 mm over length 6.4 mm (from Z=0.0 to Z=44.9).\n10. Finish turn diameter Ø30.0 mm over length 38.5 mm (from Z=0.0 to Z=38.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00240
|
images/Shaft_00240.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø55.3 mm and length at least 102.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.3 mm over length 15.0 mm (from Z=0.0 to Z=15.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø45.5 mm over length 7.1 mm (from Z=0.0 to Z=82.9).\n9. Finish turn diameter Ø37.8 mm over length 22.4 mm (from Z=0.0 to Z=75.8).\n10. Finish turn diameter Ø30.0 mm over length 53.4 mm (from Z=0.0 to Z=53.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00723
|
images/Shaft_00723.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø42.2 mm and length at least 255.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø40.2 mm over length 20.5 mm (from Z=0.0 to Z=20.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø40.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø36.9 mm over length 16.5 mm (from Z=0.0 to Z=230.1).\n10. Finish turn diameter Ø30.1 mm over length 74.9 mm (from Z=0.0 to Z=213.6).\n11. Finish turn diameter Ø30.0 mm over length 138.7 mm (from Z=0.0 to Z=138.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00609
|
images/Shaft_00609.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø48.7 mm and length at least 280.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø46.7 mm over length 16.2 mm (from Z=0.0 to Z=16.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø46.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.6 mm over length 92.5 mm (from Z=0.0 to Z=259.3).\n10. Finish turn diameter Ø30.0 mm over length 166.8 mm (from Z=0.0 to Z=166.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00766
|
images/Shaft_00766.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø50.6 mm and length at least 194.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø48.6 mm over length 52.6 mm (from Z=0.0 to Z=52.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø48.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø39.0 mm over length 63.3 mm (from Z=0.0 to Z=136.9).\n9. Finish turn diameter Ø31.2 mm over length 33.6 mm (from Z=0.0 to Z=73.6).\n10. Finish turn diameter Ø30.0 mm over length 40.0 mm (from Z=0.0 to Z=40.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00190
|
images/Shaft_00190.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø81.6 mm and length at least 72.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø79.6 mm over length 5.2 mm (from Z=0.0 to Z=5.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø79.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø76.2 mm over length 22.7 mm (from Z=0.0 to Z=62.3).\n9. Finish turn diameter Ø60.6 mm over length 39.6 mm (from Z=0.0 to Z=39.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00082
|
images/Shaft_00082.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø70.6 mm and length at least 229.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø68.6 mm over length 84.7 mm (from Z=0.0 to Z=84.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø68.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø49.4 mm over length 9.8 mm (from Z=0.0 to Z=139.4).\n10. Finish turn diameter Ø41.7 mm over length 73.2 mm (from Z=0.0 to Z=129.6).\n11. Finish turn diameter Ø32.0 mm over length 56.4 mm (from Z=0.0 to Z=56.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00520
|
images/Shaft_00520.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø36.4 mm and length at least 284.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø34.4 mm over length 21.5 mm (from Z=0.0 to Z=21.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø34.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 257.6 mm (from Z=0.0 to Z=257.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00876
|
images/Shaft_00876.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.3 mm and length at least 218.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.3 mm over length 71.0 mm (from Z=0.0 to Z=71.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 142.7 mm (from Z=0.0 to Z=142.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00805
|
images/Shaft_00805.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø59.5 mm and length at least 280.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.5 mm over length 37.9 mm (from Z=0.0 to Z=37.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø44.9 mm over length 53.4 mm (from Z=0.0 to Z=237.4).\n10. Finish turn diameter Ø30.0 mm over length 184.0 mm (from Z=0.0 to Z=184.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00783
|
images/Shaft_00783.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø62.1 mm and length at least 271.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø60.1 mm over length 39.7 mm (from Z=0.0 to Z=39.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø60.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø47.7 mm over length 49.1 mm (from Z=0.0 to Z=226.4).\n10. Finish turn diameter Ø42.0 mm over length 36.5 mm (from Z=0.0 to Z=177.3).\n11. Finish turn diameter Ø35.5 mm over length 64.7 mm (from Z=0.0 to Z=140.8).\n12. Finish turn diameter Ø30.0 mm over length 76.1 mm (from Z=0.0 to Z=76.1).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00514
|
images/Shaft_00514.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 262.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 199.7 mm (from Z=0.0 to Z=199.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø27.6 mm over length 57.5 mm (from Z=0.0 to Z=57.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00488
|
images/Shaft_00488.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø45.7 mm and length at least 251.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø43.7 mm over length 62.7 mm (from Z=0.0 to Z=62.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø43.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø39.8 mm over length 28.9 mm (from Z=0.0 to Z=183.9).\n10. Finish turn diameter Ø30.0 mm over length 155.0 mm (from Z=0.0 to Z=155.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00847
|
images/Shaft_00847.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø63.7 mm and length at least 253.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø61.7 mm over length 34.0 mm (from Z=0.0 to Z=34.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø61.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø51.0 mm over length 26.4 mm (from Z=0.0 to Z=214.3).\n10. Finish turn diameter Ø39.0 mm over length 95.3 mm (from Z=0.0 to Z=187.9).\n11. Finish turn diameter Ø30.0 mm over length 92.6 mm (from Z=0.0 to Z=92.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00672
|
images/Shaft_00672.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø43.3 mm and length at least 108.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.3 mm over length 44.1 mm (from Z=0.0 to Z=44.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø33.3 mm over length 8.5 mm (from Z=0.0 to Z=58.9).\n9. Finish turn diameter Ø30.0 mm over length 50.4 mm (from Z=0.0 to Z=50.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00058
|
images/Shaft_00058.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 116.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 89.1 mm (from Z=0.0 to Z=89.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø28.9 mm over length 22.8 mm (from Z=0.0 to Z=22.8).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00321
|
images/Shaft_00321.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø69.1 mm and length at least 155.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.1 mm over length 37.4 mm (from Z=0.0 to Z=37.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø50.7 mm over length 57.2 mm (from Z=0.0 to Z=112.9).\n9. Finish turn diameter Ø44.8 mm over length 29.6 mm (from Z=0.0 to Z=55.7).\n10. Finish turn diameter Ø37.9 mm over length 26.1 mm (from Z=0.0 to Z=26.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00691
|
images/Shaft_00691.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø46.3 mm and length at least 178.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø44.3 mm over length 44.6 mm (from Z=0.0 to Z=44.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø44.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 129.2 mm (from Z=0.0 to Z=129.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00555
|
images/Shaft_00555.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø44.8 mm and length at least 246.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø42.8 mm over length 19.1 mm (from Z=0.0 to Z=19.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø42.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø37.1 mm over length 135.1 mm (from Z=0.0 to Z=222.4).\n10. Finish turn diameter Ø30.0 mm over length 87.3 mm (from Z=0.0 to Z=87.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00593
|
images/Shaft_00593.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø48.1 mm and length at least 183.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø46.1 mm over length 56.9 mm (from Z=0.0 to Z=56.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø46.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø37.4 mm over length 65.9 mm (from Z=0.0 to Z=121.2).\n9. Finish turn diameter Ø30.0 mm over length 55.3 mm (from Z=0.0 to Z=55.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00837
|
images/Shaft_00837.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø61.9 mm and length at least 158.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø59.9 mm over length 35.3 mm (from Z=0.0 to Z=35.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø59.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø47.3 mm over length 7.0 mm (from Z=0.0 to Z=118.2).\n9. Finish turn diameter Ø33.3 mm over length 28.5 mm (from Z=0.0 to Z=111.2).\n10. Finish turn diameter Ø30.0 mm over length 82.7 mm (from Z=0.0 to Z=82.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00222
|
images/Shaft_00222.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.6 mm and length at least 106.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.6 mm over length 32.5 mm (from Z=0.0 to Z=32.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 68.6 mm (from Z=0.0 to Z=68.6).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00303
|
images/Shaft_00303.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 295.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 195.6 mm (from Z=0.0 to Z=195.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø18.7 mm over length 94.6 mm (from Z=0.0 to Z=94.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00716
|
images/Shaft_00716.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø51.7 mm and length at least 106.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø49.7 mm over length 32.4 mm (from Z=0.0 to Z=32.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø49.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø45.8 mm over length 22.4 mm (from Z=0.0 to Z=69.0).\n9. Finish turn diameter Ø30.0 mm over length 46.6 mm (from Z=0.0 to Z=46.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00158
|
images/Shaft_00158.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø46.0 mm and length at least 324.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø44.0 mm over length 80.6 mm (from Z=0.0 to Z=80.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø44.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 238.4 mm (from Z=0.0 to Z=238.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00498
|
images/Shaft_00498.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø65.2 mm and length at least 246.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.2 mm over length 97.1 mm (from Z=0.0 to Z=97.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø53.1 mm over length 42.0 mm (from Z=0.0 to Z=144.5).\n10. Finish turn diameter Ø35.4 mm over length 102.5 mm (from Z=0.0 to Z=102.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00569
|
images/Shaft_00569.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø45.6 mm and length at least 301.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø43.6 mm over length 127.0 mm (from Z=0.0 to Z=127.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø43.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø40.4 mm over length 32.6 mm (from Z=0.0 to Z=169.1).\n10. Finish turn diameter Ø31.6 mm over length 50.3 mm (from Z=0.0 to Z=136.5).\n11. Finish turn diameter Ø30.0 mm over length 86.2 mm (from Z=0.0 to Z=86.2).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00897
|
images/Shaft_00897.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø39.1 mm and length at least 207.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø37.1 mm over length 47.1 mm (from Z=0.0 to Z=47.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø37.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 155.0 mm (from Z=0.0 to Z=155.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00292
|
images/Shaft_00292.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø66.9 mm and length at least 251.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø64.9 mm over length 65.2 mm (from Z=0.0 to Z=65.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø64.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø47.8 mm over length 47.2 mm (from Z=0.0 to Z=180.9).\n10. Finish turn diameter Ø35.8 mm over length 73.9 mm (from Z=0.0 to Z=133.7).\n11. Finish turn diameter Ø30.0 mm over length 59.8 mm (from Z=0.0 to Z=59.8).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00465
|
images/Shaft_00465.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø75.5 mm and length at least 209.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.5 mm over length 100.8 mm (from Z=0.0 to Z=100.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø68.4 mm over length 22.4 mm (from Z=0.0 to Z=104.1).\n10. Finish turn diameter Ø57.9 mm over length 12.2 mm (from Z=0.0 to Z=81.7).\n11. Finish turn diameter Ø51.5 mm over length 52.4 mm (from Z=0.0 to Z=69.5).\n12. Finish turn diameter Ø31.5 mm over length 17.1 mm (from Z=0.0 to Z=17.1).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00988
|
images/Shaft_00988.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø43.4 mm and length at least 209.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.4 mm over length 80.0 mm (from Z=0.0 to Z=80.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 124.4 mm (from Z=0.0 to Z=124.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00399
|
images/Shaft_00399.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø52.2 mm and length at least 211.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø50.2 mm over length 72.9 mm (from Z=0.0 to Z=72.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø50.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.3 mm over length 67.1 mm (from Z=0.0 to Z=133.9).\n10. Finish turn diameter Ø30.0 mm over length 66.8 mm (from Z=0.0 to Z=66.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00002
|
images/Shaft_00002.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø74.9 mm and length at least 71.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.9 mm over length 5.0 mm (from Z=0.0 to Z=5.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø64.5 mm over length 23.6 mm (from Z=0.0 to Z=61.5).\n9. Finish turn diameter Ø59.0 mm over length 7.1 mm (from Z=0.0 to Z=37.9).\n10. Finish turn diameter Ø56.0 mm over length 30.8 mm (from Z=0.0 to Z=30.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00886
|
images/Shaft_00886.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø46.7 mm and length at least 87.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø44.7 mm over length 6.6 mm (from Z=0.0 to Z=6.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø44.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø32.5 mm over length 25.8 mm (from Z=0.0 to Z=76.3).\n9. Finish turn diameter Ø30.0 mm over length 50.5 mm (from Z=0.0 to Z=50.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00168
|
images/Shaft_00168.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø66.7 mm and length at least 260.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø64.7 mm over length 18.1 mm (from Z=0.0 to Z=18.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø64.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø48.7 mm over length 124.5 mm (from Z=0.0 to Z=237.5).\n10. Finish turn diameter Ø36.4 mm over length 113.0 mm (from Z=0.0 to Z=113.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00725
|
images/Shaft_00725.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø56.7 mm and length at least 306.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.7 mm over length 28.1 mm (from Z=0.0 to Z=28.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø41.6 mm over length 126.7 mm (from Z=0.0 to Z=273.6).\n10. Finish turn diameter Ø34.3 mm over length 35.2 mm (from Z=0.0 to Z=146.9).\n11. Finish turn diameter Ø30.0 mm over length 111.7 mm (from Z=0.0 to Z=111.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00869
|
images/Shaft_00869.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø59.4 mm and length at least 276.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.4 mm over length 99.8 mm (from Z=0.0 to Z=99.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø52.8 mm over length 119.6 mm (from Z=0.0 to Z=171.7).\n10. Finish turn diameter Ø41.5 mm over length 52.1 mm (from Z=0.0 to Z=52.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00218
|
images/Shaft_00218.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø66.7 mm and length at least 324.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø64.7 mm over length 115.3 mm (from Z=0.0 to Z=115.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø64.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø60.4 mm over length 100.1 mm (from Z=0.0 to Z=204.3).\n10. Finish turn diameter Ø44.3 mm over length 104.2 mm (from Z=0.0 to Z=104.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00492
|
images/Shaft_00492.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø54.5 mm and length at least 203.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø52.5 mm over length 40.0 mm (from Z=0.0 to Z=40.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø52.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.4 mm over length 44.9 mm (from Z=0.0 to Z=158.7).\n10. Finish turn diameter Ø30.0 mm over length 113.8 mm (from Z=0.0 to Z=113.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00715
|
images/Shaft_00715.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø62.9 mm and length at least 229.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø60.9 mm over length 52.3 mm (from Z=0.0 to Z=52.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø60.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø46.8 mm over length 70.3 mm (from Z=0.0 to Z=172.6).\n10. Finish turn diameter Ø32.3 mm over length 102.3 mm (from Z=0.0 to Z=102.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00751
|
images/Shaft_00751.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 195.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 179.7 mm (from Z=0.0 to Z=179.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø29.2 mm over length 10.9 mm (from Z=0.0 to Z=10.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00170
|
images/Shaft_00170.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø78.1 mm and length at least 270.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø76.1 mm over length 30.8 mm (from Z=0.0 to Z=30.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø76.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø57.6 mm over length 159.4 mm (from Z=0.0 to Z=235.1).\n10. Finish turn diameter Ø52.3 mm over length 75.7 mm (from Z=0.0 to Z=75.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00242
|
images/Shaft_00242.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø43.1 mm and length at least 304.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.1 mm over length 68.4 mm (from Z=0.0 to Z=68.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø33.9 mm over length 119.8 mm (from Z=0.0 to Z=231.2).\n10. Finish turn diameter Ø30.0 mm over length 111.4 mm (from Z=0.0 to Z=111.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00980
|
images/Shaft_00980.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø42.5 mm and length at least 218.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø40.5 mm over length 129.2 mm (from Z=0.0 to Z=129.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø40.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø33.4 mm over length 30.5 mm (from Z=0.0 to Z=84.5).\n10. Finish turn diameter Ø30.0 mm over length 54.0 mm (from Z=0.0 to Z=54.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00015
|
images/Shaft_00015.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø59.6 mm and length at least 123.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.6 mm over length 43.6 mm (from Z=0.0 to Z=43.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø50.5 mm over length 33.3 mm (from Z=0.0 to Z=75.3).\n9. Finish turn diameter Ø34.1 mm over length 42.0 mm (from Z=0.0 to Z=42.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00553
|
images/Shaft_00553.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø81.8 mm and length at least 83.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø79.8 mm over length 12.2 mm (from Z=0.0 to Z=12.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø79.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø66.0 mm over length 16.7 mm (from Z=0.0 to Z=65.8).\n9. Finish turn diameter Ø47.3 mm over length 18.9 mm (from Z=0.0 to Z=49.1).\n10. Finish turn diameter Ø33.5 mm over length 20.2 mm (from Z=0.0 to Z=30.2).\n11. Finish turn diameter Ø30.0 mm over length 10.0 mm (from Z=0.0 to Z=10.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00667
|
images/Shaft_00667.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø57.2 mm and length at least 251.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø55.2 mm over length 53.1 mm (from Z=0.0 to Z=53.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø55.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø40.5 mm over length 12.6 mm (from Z=0.0 to Z=193.4).\n10. Finish turn diameter Ø34.0 mm over length 50.2 mm (from Z=0.0 to Z=180.8).\n11. Finish turn diameter Ø30.0 mm over length 130.6 mm (from Z=0.0 to Z=130.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00051
|
images/Shaft_00051.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø62.5 mm and length at least 302.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø60.5 mm over length 21.5 mm (from Z=0.0 to Z=21.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø60.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø53.5 mm over length 70.3 mm (from Z=0.0 to Z=275.8).\n10. Finish turn diameter Ø45.4 mm over length 62.6 mm (from Z=0.0 to Z=205.5).\n11. Finish turn diameter Ø38.6 mm over length 77.6 mm (from Z=0.0 to Z=142.9).\n12. Finish turn diameter Ø35.2 mm over length 29.4 mm (from Z=0.0 to Z=65.3).\n13. Finish turn diameter Ø30.0 mm over length 35.9 mm (from Z=0.0 to Z=35.9).\n14. Break all edges (e.g., 2×45° where applicable).\n15. Remove the workpiece from the lathe."
}
] |
Shaft_00989
|
images/Shaft_00989.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø56.0 mm and length at least 323.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.0 mm over length 118.3 mm (from Z=0.0 to Z=118.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.2 mm over length 28.0 mm (from Z=0.0 to Z=200.6).\n10. Finish turn diameter Ø35.1 mm over length 44.0 mm (from Z=0.0 to Z=172.6).\n11. Finish turn diameter Ø30.0 mm over length 128.6 mm (from Z=0.0 to Z=128.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00563
|
images/Shaft_00563.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø53.7 mm and length at least 240.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø51.7 mm over length 21.4 mm (from Z=0.0 to Z=21.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø51.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø43.1 mm over length 51.0 mm (from Z=0.0 to Z=214.3).\n10. Finish turn diameter Ø30.0 mm over length 163.3 mm (from Z=0.0 to Z=163.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00453
|
images/Shaft_00453.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 103.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 85.3 mm (from Z=0.0 to Z=85.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø26.3 mm over length 13.4 mm (from Z=0.0 to Z=13.4).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00077
|
images/Shaft_00077.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø70.5 mm and length at least 295.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø68.5 mm over length 95.7 mm (from Z=0.0 to Z=95.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø68.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø58.3 mm over length 68.0 mm (from Z=0.0 to Z=194.8).\n10. Finish turn diameter Ø54.8 mm over length 79.1 mm (from Z=0.0 to Z=126.8).\n11. Finish turn diameter Ø40.0 mm over length 47.7 mm (from Z=0.0 to Z=47.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00255
|
images/Shaft_00255.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø38.5 mm and length at least 301.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.5 mm over length 21.9 mm (from Z=0.0 to Z=21.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 274.5 mm (from Z=0.0 to Z=274.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00912
|
images/Shaft_00912.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 257.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 229.0 mm (from Z=0.0 to Z=229.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø21.8 mm over length 23.1 mm (from Z=0.0 to Z=23.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00717
|
images/Shaft_00717.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø63.5 mm and length at least 138.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø61.5 mm over length 12.7 mm (from Z=0.0 to Z=12.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø61.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø53.6 mm over length 22.6 mm (from Z=0.0 to Z=120.8).\n9. Finish turn diameter Ø50.0 mm over length 40.1 mm (from Z=0.0 to Z=98.2).\n10. Finish turn diameter Ø41.5 mm over length 43.2 mm (from Z=0.0 to Z=58.1).\n11. Finish turn diameter Ø30.0 mm over length 14.9 mm (from Z=0.0 to Z=14.9).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00187
|
images/Shaft_00187.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø69.5 mm and length at least 225.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.5 mm over length 112.9 mm (from Z=0.0 to Z=112.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø63.1 mm over length 93.9 mm (from Z=0.0 to Z=107.7).\n10. Finish turn diameter Ø54.9 mm over length 13.8 mm (from Z=0.0 to Z=13.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00829
|
images/Shaft_00829.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø58.4 mm and length at least 302.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø56.4 mm over length 103.4 mm (from Z=0.0 to Z=103.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø56.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø43.5 mm over length 116.8 mm (from Z=0.0 to Z=194.4).\n10. Finish turn diameter Ø37.9 mm over length 77.6 mm (from Z=0.0 to Z=77.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00143
|
images/Shaft_00143.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø68.7 mm and length at least 294.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø66.7 mm over length 33.1 mm (from Z=0.0 to Z=33.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø66.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø54.2 mm over length 54.1 mm (from Z=0.0 to Z=256.8).\n10. Finish turn diameter Ø39.8 mm over length 55.9 mm (from Z=0.0 to Z=202.7).\n11. Finish turn diameter Ø30.0 mm over length 146.8 mm (from Z=0.0 to Z=146.8).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00966
|
images/Shaft_00966.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 247.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 214.6 mm (from Z=0.0 to Z=214.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø28.6 mm over length 28.3 mm (from Z=0.0 to Z=28.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00814
|
images/Shaft_00814.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 273.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 190.8 mm (from Z=0.0 to Z=190.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø28.7 mm over length 77.9 mm (from Z=0.0 to Z=77.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00705
|
images/Shaft_00705.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø56.5 mm and length at least 172.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.5 mm over length 57.6 mm (from Z=0.0 to Z=57.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø42.5 mm over length 21.5 mm (from Z=0.0 to Z=109.5).\n9. Finish turn diameter Ø35.1 mm over length 39.2 mm (from Z=0.0 to Z=88.0).\n10. Finish turn diameter Ø30.0 mm over length 48.8 mm (from Z=0.0 to Z=48.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00923
|
images/Shaft_00923.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø72.9 mm and length at least 97.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø70.9 mm over length 38.4 mm (from Z=0.0 to Z=38.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø70.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø60.9 mm over length 18.5 mm (from Z=0.0 to Z=53.7).\n9. Finish turn diameter Ø54.7 mm over length 9.7 mm (from Z=0.0 to Z=35.2).\n10. Finish turn diameter Ø42.6 mm over length 25.5 mm (from Z=0.0 to Z=25.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00254
|
images/Shaft_00254.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø72.5 mm and length at least 186.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø70.5 mm over length 8.8 mm (from Z=0.0 to Z=8.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø70.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø54.4 mm over length 82.2 mm (from Z=0.0 to Z=173.0).\n9. Finish turn diameter Ø51.2 mm over length 82.9 mm (from Z=0.0 to Z=90.8).\n10. Finish turn diameter Ø41.1 mm over length 7.9 mm (from Z=0.0 to Z=7.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00111
|
images/Shaft_00111.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø35.3 mm and length at least 73.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.3 mm over length 13.0 mm (from Z=0.0 to Z=13.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 55.2 mm (from Z=0.0 to Z=55.2).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00347
|
images/Shaft_00347.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø76.4 mm and length at least 102.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø74.4 mm over length 20.7 mm (from Z=0.0 to Z=20.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø74.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø55.7 mm over length 52.4 mm (from Z=0.0 to Z=77.1).\n9. Finish turn diameter Ø49.7 mm over length 9.2 mm (from Z=0.0 to Z=24.7).\n10. Finish turn diameter Ø30.8 mm over length 15.5 mm (from Z=0.0 to Z=15.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00412
|
images/Shaft_00412.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø70.8 mm and length at least 278.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø68.8 mm over length 15.5 mm (from Z=0.0 to Z=15.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø68.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø59.0 mm over length 37.6 mm (from Z=0.0 to Z=257.7).\n10. Finish turn diameter Ø45.2 mm over length 60.8 mm (from Z=0.0 to Z=220.1).\n11. Finish turn diameter Ø39.6 mm over length 55.3 mm (from Z=0.0 to Z=159.3).\n12. Finish turn diameter Ø30.0 mm over length 104.0 mm (from Z=0.0 to Z=104.0).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00062
|
images/Shaft_00062.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø65.0 mm and length at least 301.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.0 mm over length 43.5 mm (from Z=0.0 to Z=43.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø57.4 mm over length 35.1 mm (from Z=0.0 to Z=253.1).\n10. Finish turn diameter Ø51.4 mm over length 52.8 mm (from Z=0.0 to Z=218.0).\n11. Finish turn diameter Ø33.1 mm over length 39.0 mm (from Z=0.0 to Z=165.2).\n12. Finish turn diameter Ø30.0 mm over length 126.2 mm (from Z=0.0 to Z=126.2).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00100
|
images/Shaft_00100.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø41.6 mm and length at least 189.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø39.6 mm over length 68.2 mm (from Z=0.0 to Z=68.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø39.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 116.2 mm (from Z=0.0 to Z=116.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00661
|
images/Shaft_00661.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø69.4 mm and length at least 84.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.4 mm over length 5.0 mm (from Z=0.0 to Z=5.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø62.2 mm over length 23.0 mm (from Z=0.0 to Z=74.3).\n9. Finish turn diameter Ø52.4 mm over length 21.2 mm (from Z=0.0 to Z=51.3).\n10. Finish turn diameter Ø45.1 mm over length 15.4 mm (from Z=0.0 to Z=30.1).\n11. Finish turn diameter Ø31.6 mm over length 5.7 mm (from Z=0.0 to Z=14.7).\n12. Finish turn diameter Ø30.0 mm over length 9.0 mm (from Z=0.0 to Z=9.0).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00669
|
images/Shaft_00669.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø50.0 mm and length at least 287.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø48.0 mm over length 40.1 mm (from Z=0.0 to Z=40.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø48.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø32.9 mm over length 19.7 mm (from Z=0.0 to Z=241.9).\n10. Finish turn diameter Ø30.0 mm over length 222.2 mm (from Z=0.0 to Z=222.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00689
|
images/Shaft_00689.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø63.9 mm and length at least 280.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø61.9 mm over length 29.3 mm (from Z=0.0 to Z=29.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø61.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø58.4 mm over length 126.9 mm (from Z=0.0 to Z=246.0).\n10. Finish turn diameter Ø52.2 mm over length 119.1 mm (from Z=0.0 to Z=119.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00055
|
images/Shaft_00055.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø74.6 mm and length at least 134.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.6 mm over length 31.2 mm (from Z=0.0 to Z=31.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø58.2 mm over length 25.4 mm (from Z=0.0 to Z=97.8).\n9. Finish turn diameter Ø54.8 mm over length 30.2 mm (from Z=0.0 to Z=72.4).\n10. Finish turn diameter Ø40.9 mm over length 6.1 mm (from Z=0.0 to Z=42.2).\n11. Finish turn diameter Ø30.3 mm over length 20.3 mm (from Z=0.0 to Z=36.1).\n12. Finish turn diameter Ø30.0 mm over length 15.8 mm (from Z=0.0 to Z=15.8).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00478
|
images/Shaft_00478.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø51.7 mm and length at least 210.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø49.7 mm over length 40.3 mm (from Z=0.0 to Z=40.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø49.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø44.8 mm over length 25.3 mm (from Z=0.0 to Z=165.5).\n10. Finish turn diameter Ø32.4 mm over length 38.5 mm (from Z=0.0 to Z=140.2).\n11. Finish turn diameter Ø30.0 mm over length 101.7 mm (from Z=0.0 to Z=101.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00420
|
images/Shaft_00420.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø78.6 mm and length at least 144.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø76.6 mm over length 54.8 mm (from Z=0.0 to Z=54.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø76.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø68.2 mm over length 11.9 mm (from Z=0.0 to Z=84.8).\n9. Finish turn diameter Ø57.1 mm over length 41.5 mm (from Z=0.0 to Z=72.9).\n10. Finish turn diameter Ø47.0 mm over length 31.4 mm (from Z=0.0 to Z=31.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00755
|
images/Shaft_00755.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 194.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 125.8 mm (from Z=0.0 to Z=125.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø27.0 mm over length 63.8 mm (from Z=0.0 to Z=63.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.