id
stringlengths 11
11
| image
stringlengths 22
22
| conversations
listlengths 2
2
|
|---|---|---|
Shaft_00927
|
images/Shaft_00927.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 272.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 190.1 mm (from Z=0.0 to Z=190.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø27.4 mm over length 77.2 mm (from Z=0.0 to Z=77.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00659
|
images/Shaft_00659.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø35.9 mm and length at least 311.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.9 mm over length 32.9 mm (from Z=0.0 to Z=32.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 273.7 mm (from Z=0.0 to Z=273.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00636
|
images/Shaft_00636.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 321.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 232.4 mm (from Z=0.0 to Z=232.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø25.8 mm over length 84.0 mm (from Z=0.0 to Z=84.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00098
|
images/Shaft_00098.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø60.2 mm and length at least 276.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø58.2 mm over length 124.0 mm (from Z=0.0 to Z=124.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø58.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø50.0 mm over length 49.9 mm (from Z=0.0 to Z=147.0).\n10. Finish turn diameter Ø39.5 mm over length 34.9 mm (from Z=0.0 to Z=97.1).\n11. Finish turn diameter Ø30.0 mm over length 62.2 mm (from Z=0.0 to Z=62.2).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00337
|
images/Shaft_00337.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø35.8 mm and length at least 261.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.8 mm over length 57.8 mm (from Z=0.0 to Z=57.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 198.2 mm (from Z=0.0 to Z=198.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00012
|
images/Shaft_00012.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø69.1 mm and length at least 288.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.1 mm over length 62.7 mm (from Z=0.0 to Z=62.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø47.7 mm over length 68.1 mm (from Z=0.0 to Z=220.4).\n10. Finish turn diameter Ø37.3 mm over length 7.7 mm (from Z=0.0 to Z=152.3).\n11. Finish turn diameter Ø30.0 mm over length 144.6 mm (from Z=0.0 to Z=144.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00684
|
images/Shaft_00684.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø49.9 mm and length at least 87.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø47.9 mm over length 16.7 mm (from Z=0.0 to Z=16.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø47.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø39.3 mm over length 9.3 mm (from Z=0.0 to Z=65.3).\n9. Finish turn diameter Ø30.0 mm over length 56.0 mm (from Z=0.0 to Z=56.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00116
|
images/Shaft_00116.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø39.0 mm and length at least 290.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø37.0 mm over length 14.3 mm (from Z=0.0 to Z=14.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø37.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 270.7 mm (from Z=0.0 to Z=270.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00446
|
images/Shaft_00446.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø41.2 mm and length at least 292.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø39.2 mm over length 66.4 mm (from Z=0.0 to Z=66.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø39.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø34.5 mm over length 113.0 mm (from Z=0.0 to Z=220.7).\n10. Finish turn diameter Ø30.0 mm over length 107.7 mm (from Z=0.0 to Z=107.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00407
|
images/Shaft_00407.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø62.0 mm and length at least 263.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø60.0 mm over length 115.3 mm (from Z=0.0 to Z=115.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø60.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø42.0 mm over length 68.8 mm (from Z=0.0 to Z=143.3).\n10. Finish turn diameter Ø30.8 mm over length 74.5 mm (from Z=0.0 to Z=74.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00815
|
images/Shaft_00815.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø64.6 mm and length at least 160.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø62.6 mm over length 28.4 mm (from Z=0.0 to Z=28.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø62.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø49.6 mm over length 20.4 mm (from Z=0.0 to Z=126.6).\n9. Finish turn diameter Ø33.7 mm over length 79.4 mm (from Z=0.0 to Z=106.2).\n10. Finish turn diameter Ø30.0 mm over length 26.8 mm (from Z=0.0 to Z=26.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00312
|
images/Shaft_00312.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø37.4 mm and length at least 157.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø35.4 mm over length 37.0 mm (from Z=0.0 to Z=37.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø35.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 115.4 mm (from Z=0.0 to Z=115.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00358
|
images/Shaft_00358.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø80.2 mm and length at least 272.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.2 mm over length 68.2 mm (from Z=0.0 to Z=68.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø71.2 mm over length 49.7 mm (from Z=0.0 to Z=199.5).\n10. Finish turn diameter Ø54.7 mm over length 98.5 mm (from Z=0.0 to Z=149.8).\n11. Finish turn diameter Ø51.1 mm over length 18.5 mm (from Z=0.0 to Z=51.3).\n12. Finish turn diameter Ø34.7 mm over length 32.8 mm (from Z=0.0 to Z=32.8).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00471
|
images/Shaft_00471.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø62.1 mm and length at least 94.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø60.1 mm over length 40.1 mm (from Z=0.0 to Z=40.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø60.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø50.6 mm over length 9.9 mm (from Z=0.0 to Z=49.1).\n9. Finish turn diameter Ø43.2 mm over length 14.0 mm (from Z=0.0 to Z=39.2).\n10. Finish turn diameter Ø30.0 mm over length 25.2 mm (from Z=0.0 to Z=25.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00204
|
images/Shaft_00204.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø69.1 mm and length at least 149.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.1 mm over length 26.1 mm (from Z=0.0 to Z=26.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø54.3 mm over length 27.4 mm (from Z=0.0 to Z=118.1).\n9. Finish turn diameter Ø44.2 mm over length 27.3 mm (from Z=0.0 to Z=90.7).\n10. Finish turn diameter Ø36.4 mm over length 34.6 mm (from Z=0.0 to Z=63.4).\n11. Finish turn diameter Ø30.0 mm over length 28.8 mm (from Z=0.0 to Z=28.8).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00227
|
images/Shaft_00227.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø78.6 mm and length at least 262.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø76.6 mm over length 23.4 mm (from Z=0.0 to Z=23.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø76.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø70.2 mm over length 191.2 mm (from Z=0.0 to Z=234.4).\n10. Finish turn diameter Ø50.8 mm over length 43.2 mm (from Z=0.0 to Z=43.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00481
|
images/Shaft_00481.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø46.2 mm and length at least 137.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø44.2 mm over length 6.4 mm (from Z=0.0 to Z=6.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø44.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø38.8 mm over length 62.0 mm (from Z=0.0 to Z=125.8).\n9. Finish turn diameter Ø30.0 mm over length 63.8 mm (from Z=0.0 to Z=63.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00039
|
images/Shaft_00039.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø34.9 mm and length at least 304.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.9 mm over length 14.2 mm (from Z=0.0 to Z=14.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 284.8 mm (from Z=0.0 to Z=284.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00391
|
images/Shaft_00391.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 242.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 144.4 mm (from Z=0.0 to Z=144.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø23.9 mm over length 92.8 mm (from Z=0.0 to Z=92.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00110
|
images/Shaft_00110.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø74.2 mm and length at least 283.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.2 mm over length 63.3 mm (from Z=0.0 to Z=63.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø58.7 mm over length 151.7 mm (from Z=0.0 to Z=214.8).\n10. Finish turn diameter Ø48.2 mm over length 63.1 mm (from Z=0.0 to Z=63.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00832
|
images/Shaft_00832.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 217.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 157.2 mm (from Z=0.0 to Z=157.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø21.2 mm over length 55.0 mm (from Z=0.0 to Z=55.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00812
|
images/Shaft_00812.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø81.0 mm and length at least 257.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø79.0 mm over length 47.1 mm (from Z=0.0 to Z=47.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø79.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø62.3 mm over length 53.2 mm (from Z=0.0 to Z=205.6).\n10. Finish turn diameter Ø58.2 mm over length 42.5 mm (from Z=0.0 to Z=152.4).\n11. Finish turn diameter Ø40.2 mm over length 63.3 mm (from Z=0.0 to Z=109.9).\n12. Finish turn diameter Ø30.0 mm over length 46.6 mm (from Z=0.0 to Z=46.6).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00962
|
images/Shaft_00962.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.3 mm and length at least 265.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.3 mm over length 60.1 mm (from Z=0.0 to Z=60.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 199.9 mm (from Z=0.0 to Z=199.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00421
|
images/Shaft_00421.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø45.2 mm and length at least 252.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø43.2 mm over length 23.6 mm (from Z=0.0 to Z=23.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø43.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 224.1 mm (from Z=0.0 to Z=224.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00340
|
images/Shaft_00340.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø54.1 mm and length at least 194.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø52.1 mm over length 27.2 mm (from Z=0.0 to Z=27.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø52.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø44.8 mm over length 135.0 mm (from Z=0.0 to Z=162.2).\n10. Finish turn diameter Ø32.9 mm over length 27.2 mm (from Z=0.0 to Z=27.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00183
|
images/Shaft_00183.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø69.6 mm and length at least 233.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.6 mm over length 119.0 mm (from Z=0.0 to Z=119.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø61.6 mm over length 40.3 mm (from Z=0.0 to Z=109.5).\n10. Finish turn diameter Ø53.6 mm over length 69.2 mm (from Z=0.0 to Z=69.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00997
|
images/Shaft_00997.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø74.8 mm and length at least 292.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.8 mm over length 96.4 mm (from Z=0.0 to Z=96.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø54.7 mm over length 77.3 mm (from Z=0.0 to Z=190.9).\n10. Finish turn diameter Ø47.1 mm over length 77.6 mm (from Z=0.0 to Z=113.6).\n11. Finish turn diameter Ø38.0 mm over length 36.0 mm (from Z=0.0 to Z=36.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00422
|
images/Shaft_00422.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø51.5 mm and length at least 298.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø49.5 mm over length 73.7 mm (from Z=0.0 to Z=73.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø49.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.8 mm over length 116.5 mm (from Z=0.0 to Z=219.3).\n10. Finish turn diameter Ø30.0 mm over length 102.8 mm (from Z=0.0 to Z=102.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00181
|
images/Shaft_00181.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø47.1 mm and length at least 257.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø45.1 mm over length 84.1 mm (from Z=0.0 to Z=84.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø45.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.5 mm over length 55.4 mm (from Z=0.0 to Z=168.3).\n10. Finish turn diameter Ø30.0 mm over length 112.9 mm (from Z=0.0 to Z=112.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00904
|
images/Shaft_00904.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø56.9 mm and length at least 165.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.9 mm over length 12.7 mm (from Z=0.0 to Z=12.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø41.3 mm over length 65.8 mm (from Z=0.0 to Z=147.9).\n9. Finish turn diameter Ø34.3 mm over length 82.1 mm (from Z=0.0 to Z=82.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00861
|
images/Shaft_00861.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø52.9 mm and length at least 150.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø50.9 mm over length 67.3 mm (from Z=0.0 to Z=67.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø50.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø34.1 mm over length 17.1 mm (from Z=0.0 to Z=78.6).\n9. Finish turn diameter Ø30.0 mm over length 61.5 mm (from Z=0.0 to Z=61.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00649
|
images/Shaft_00649.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø59.8 mm and length at least 276.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.8 mm over length 23.3 mm (from Z=0.0 to Z=23.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø52.0 mm over length 76.4 mm (from Z=0.0 to Z=248.6).\n10. Finish turn diameter Ø43.2 mm over length 172.2 mm (from Z=0.0 to Z=172.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00745
|
images/Shaft_00745.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø55.9 mm and length at least 194.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.9 mm over length 9.3 mm (from Z=0.0 to Z=9.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø46.5 mm over length 54.1 mm (from Z=0.0 to Z=180.2).\n9. Finish turn diameter Ø41.4 mm over length 54.8 mm (from Z=0.0 to Z=126.1).\n10. Finish turn diameter Ø30.0 mm over length 71.3 mm (from Z=0.0 to Z=71.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00700
|
images/Shaft_00700.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø77.7 mm and length at least 324.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø75.7 mm over length 61.9 mm (from Z=0.0 to Z=61.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø75.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø57.2 mm over length 38.8 mm (from Z=0.0 to Z=257.3).\n10. Finish turn diameter Ø51.1 mm over length 65.9 mm (from Z=0.0 to Z=218.5).\n11. Finish turn diameter Ø34.9 mm over length 63.6 mm (from Z=0.0 to Z=152.6).\n12. Finish turn diameter Ø30.0 mm over length 89.0 mm (from Z=0.0 to Z=89.0).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00105
|
images/Shaft_00105.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 151.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 111.4 mm (from Z=0.0 to Z=111.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø22.6 mm over length 34.9 mm (from Z=0.0 to Z=34.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00919
|
images/Shaft_00919.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 196.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 116.6 mm (from Z=0.0 to Z=116.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø27.6 mm over length 74.5 mm (from Z=0.0 to Z=74.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00651
|
images/Shaft_00651.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø49.2 mm and length at least 275.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø47.2 mm over length 93.9 mm (from Z=0.0 to Z=93.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø47.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 177.0 mm (from Z=0.0 to Z=177.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00366
|
images/Shaft_00366.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø75.4 mm and length at least 217.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.4 mm over length 46.6 mm (from Z=0.0 to Z=46.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø58.7 mm over length 97.9 mm (from Z=0.0 to Z=166.2).\n10. Finish turn diameter Ø46.5 mm over length 68.3 mm (from Z=0.0 to Z=68.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00619
|
images/Shaft_00619.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø46.3 mm and length at least 121.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø44.3 mm over length 13.8 mm (from Z=0.0 to Z=13.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø44.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø41.1 mm over length 26.6 mm (from Z=0.0 to Z=102.7).\n9. Finish turn diameter Ø36.9 mm over length 40.8 mm (from Z=0.0 to Z=76.1).\n10. Finish turn diameter Ø30.0 mm over length 35.3 mm (from Z=0.0 to Z=35.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00905
|
images/Shaft_00905.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø49.8 mm and length at least 174.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø47.8 mm over length 40.4 mm (from Z=0.0 to Z=40.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø47.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø42.4 mm over length 11.8 mm (from Z=0.0 to Z=128.8).\n10. Finish turn diameter Ø30.0 mm over length 117.0 mm (from Z=0.0 to Z=117.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00315
|
images/Shaft_00315.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø36.6 mm and length at least 275.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø34.6 mm over length 39.0 mm (from Z=0.0 to Z=39.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø34.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 231.6 mm (from Z=0.0 to Z=231.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00042
|
images/Shaft_00042.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 143.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 77.8 mm (from Z=0.0 to Z=77.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø22.9 mm over length 60.9 mm (from Z=0.0 to Z=60.9).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00130
|
images/Shaft_00130.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø52.2 mm and length at least 255.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø50.2 mm over length 136.4 mm (from Z=0.0 to Z=136.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø50.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø39.9 mm over length 19.8 mm (from Z=0.0 to Z=114.2).\n10. Finish turn diameter Ø32.9 mm over length 45.9 mm (from Z=0.0 to Z=94.4).\n11. Finish turn diameter Ø30.0 mm over length 48.5 mm (from Z=0.0 to Z=48.5).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00440
|
images/Shaft_00440.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø54.1 mm and length at least 308.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø52.1 mm over length 46.0 mm (from Z=0.0 to Z=46.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø52.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø35.9 mm over length 53.9 mm (from Z=0.0 to Z=257.1).\n10. Finish turn diameter Ø30.0 mm over length 203.2 mm (from Z=0.0 to Z=203.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00151
|
images/Shaft_00151.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø43.8 mm and length at least 192.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.8 mm over length 68.8 mm (from Z=0.0 to Z=68.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 118.4 mm (from Z=0.0 to Z=118.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00588
|
images/Shaft_00588.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 163.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 99.8 mm (from Z=0.0 to Z=99.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø21.3 mm over length 58.6 mm (from Z=0.0 to Z=58.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00036
|
images/Shaft_00036.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø70.1 mm and length at least 209.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø68.1 mm over length 47.4 mm (from Z=0.0 to Z=47.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø68.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø59.6 mm over length 111.6 mm (from Z=0.0 to Z=156.7).\n10. Finish turn diameter Ø52.5 mm over length 45.1 mm (from Z=0.0 to Z=45.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00152
|
images/Shaft_00152.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø78.3 mm and length at least 193.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø76.3 mm over length 19.4 mm (from Z=0.0 to Z=19.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø76.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø63.6 mm over length 102.8 mm (from Z=0.0 to Z=169.0).\n9. Finish turn diameter Ø58.6 mm over length 66.2 mm (from Z=0.0 to Z=66.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00676
|
images/Shaft_00676.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø57.9 mm and length at least 322.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø55.9 mm over length 114.6 mm (from Z=0.0 to Z=114.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø55.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø41.6 mm over length 11.1 mm (from Z=0.0 to Z=203.0).\n10. Finish turn diameter Ø36.0 mm over length 68.3 mm (from Z=0.0 to Z=191.9).\n11. Finish turn diameter Ø30.0 mm over length 123.6 mm (from Z=0.0 to Z=123.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00960
|
images/Shaft_00960.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø73.0 mm and length at least 315.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø71.0 mm over length 61.9 mm (from Z=0.0 to Z=61.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø71.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø60.7 mm over length 91.3 mm (from Z=0.0 to Z=248.7).\n10. Finish turn diameter Ø48.5 mm over length 72.0 mm (from Z=0.0 to Z=157.4).\n11. Finish turn diameter Ø30.0 mm over length 85.4 mm (from Z=0.0 to Z=85.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00601
|
images/Shaft_00601.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø36.8 mm and length at least 242.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø34.8 mm over length 45.8 mm (from Z=0.0 to Z=45.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø34.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø31.5 mm over length 110.3 mm (from Z=0.0 to Z=191.9).\n10. Finish turn diameter Ø30.0 mm over length 81.6 mm (from Z=0.0 to Z=81.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00437
|
images/Shaft_00437.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 167.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 120.5 mm (from Z=0.0 to Z=120.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø21.7 mm over length 42.0 mm (from Z=0.0 to Z=42.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00452
|
images/Shaft_00452.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø68.9 mm and length at least 275.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø66.9 mm over length 128.4 mm (from Z=0.0 to Z=128.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø66.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø57.9 mm over length 18.6 mm (from Z=0.0 to Z=141.7).\n10. Finish turn diameter Ø41.0 mm over length 90.1 mm (from Z=0.0 to Z=123.1).\n11. Finish turn diameter Ø30.0 mm over length 33.0 mm (from Z=0.0 to Z=33.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00785
|
images/Shaft_00785.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø55.4 mm and length at least 316.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.4 mm over length 48.1 mm (from Z=0.0 to Z=48.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø36.5 mm over length 17.3 mm (from Z=0.0 to Z=263.2).\n10. Finish turn diameter Ø33.4 mm over length 41.8 mm (from Z=0.0 to Z=245.9).\n11. Finish turn diameter Ø30.0 mm over length 204.1 mm (from Z=0.0 to Z=204.1).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00268
|
images/Shaft_00268.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø35.4 mm and length at least 196.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.4 mm over length 66.9 mm (from Z=0.0 to Z=66.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 125.0 mm (from Z=0.0 to Z=125.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00133
|
images/Shaft_00133.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 138.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 116.2 mm (from Z=0.0 to Z=116.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø26.0 mm over length 17.1 mm (from Z=0.0 to Z=17.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00341
|
images/Shaft_00341.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 104.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 89.1 mm (from Z=0.0 to Z=89.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø27.2 mm over length 10.2 mm (from Z=0.0 to Z=10.2).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00803
|
images/Shaft_00803.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø45.0 mm and length at least 145.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø43.0 mm over length 41.1 mm (from Z=0.0 to Z=41.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø43.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø39.4 mm over length 57.9 mm (from Z=0.0 to Z=99.7).\n9. Finish turn diameter Ø30.0 mm over length 41.8 mm (from Z=0.0 to Z=41.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00045
|
images/Shaft_00045.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø43.9 mm and length at least 181.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.9 mm over length 23.9 mm (from Z=0.0 to Z=23.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 152.9 mm (from Z=0.0 to Z=152.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00283
|
images/Shaft_00283.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø72.9 mm and length at least 77.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø70.9 mm over length 37.8 mm (from Z=0.0 to Z=37.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø70.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø60.6 mm over length 12.6 mm (from Z=0.0 to Z=34.2).\n9. Finish turn diameter Ø55.7 mm over length 21.6 mm (from Z=0.0 to Z=21.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00652
|
images/Shaft_00652.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø60.2 mm and length at least 279.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø58.2 mm over length 62.1 mm (from Z=0.0 to Z=62.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø58.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø49.3 mm over length 48.3 mm (from Z=0.0 to Z=212.0).\n10. Finish turn diameter Ø40.3 mm over length 60.8 mm (from Z=0.0 to Z=163.7).\n11. Finish turn diameter Ø30.0 mm over length 102.9 mm (from Z=0.0 to Z=102.9).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00948
|
images/Shaft_00948.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø42.2 mm and length at least 98.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø40.2 mm over length 12.2 mm (from Z=0.0 to Z=12.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø40.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 80.8 mm (from Z=0.0 to Z=80.8).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00052
|
images/Shaft_00052.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø52.1 mm and length at least 279.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø50.1 mm over length 30.7 mm (from Z=0.0 to Z=30.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø50.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø34.0 mm over length 48.9 mm (from Z=0.0 to Z=243.9).\n10. Finish turn diameter Ø30.0 mm over length 195.0 mm (from Z=0.0 to Z=195.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00821
|
images/Shaft_00821.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø66.0 mm and length at least 273.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø64.0 mm over length 108.7 mm (from Z=0.0 to Z=108.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø64.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø57.9 mm over length 34.9 mm (from Z=0.0 to Z=159.3).\n10. Finish turn diameter Ø51.1 mm over length 30.4 mm (from Z=0.0 to Z=124.4).\n11. Finish turn diameter Ø45.6 mm over length 71.6 mm (from Z=0.0 to Z=94.0).\n12. Finish turn diameter Ø37.1 mm over length 22.4 mm (from Z=0.0 to Z=22.4).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00779
|
images/Shaft_00779.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø59.0 mm and length at least 84.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.0 mm over length 12.1 mm (from Z=0.0 to Z=12.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø40.5 mm over length 5.0 mm (from Z=0.0 to Z=67.1).\n9. Finish turn diameter Ø34.7 mm over length 21.4 mm (from Z=0.0 to Z=62.1).\n10. Finish turn diameter Ø30.0 mm over length 40.7 mm (from Z=0.0 to Z=40.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00977
|
images/Shaft_00977.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø57.9 mm and length at least 277.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø55.9 mm over length 87.2 mm (from Z=0.0 to Z=87.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø55.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø47.8 mm over length 94.1 mm (from Z=0.0 to Z=185.5).\n10. Finish turn diameter Ø36.8 mm over length 91.4 mm (from Z=0.0 to Z=91.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00599
|
images/Shaft_00599.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø75.7 mm and length at least 298.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.7 mm over length 33.5 mm (from Z=0.0 to Z=33.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø66.5 mm over length 70.7 mm (from Z=0.0 to Z=259.7).\n10. Finish turn diameter Ø61.2 mm over length 114.0 mm (from Z=0.0 to Z=189.0).\n11. Finish turn diameter Ø47.3 mm over length 75.0 mm (from Z=0.0 to Z=75.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00208
|
images/Shaft_00208.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø75.5 mm and length at least 284.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.5 mm over length 55.4 mm (from Z=0.0 to Z=55.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø62.9 mm over length 62.6 mm (from Z=0.0 to Z=224.2).\n10. Finish turn diameter Ø53.8 mm over length 69.6 mm (from Z=0.0 to Z=161.6).\n11. Finish turn diameter Ø44.0 mm over length 92.0 mm (from Z=0.0 to Z=92.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00351
|
images/Shaft_00351.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø34.2 mm and length at least 111.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.2 mm over length 9.0 mm (from Z=0.0 to Z=9.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 97.6 mm (from Z=0.0 to Z=97.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00215
|
images/Shaft_00215.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø68.7 mm and length at least 315.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø66.7 mm over length 88.7 mm (from Z=0.0 to Z=88.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø66.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø61.6 mm over length 41.3 mm (from Z=0.0 to Z=221.6).\n10. Finish turn diameter Ø58.1 mm over length 87.7 mm (from Z=0.0 to Z=180.3).\n11. Finish turn diameter Ø39.5 mm over length 92.6 mm (from Z=0.0 to Z=92.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00288
|
images/Shaft_00288.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø77.5 mm and length at least 96.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø75.5 mm over length 13.5 mm (from Z=0.0 to Z=13.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø75.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø64.3 mm over length 18.8 mm (from Z=0.0 to Z=77.5).\n9. Finish turn diameter Ø46.6 mm over length 11.9 mm (from Z=0.0 to Z=58.7).\n10. Finish turn diameter Ø40.4 mm over length 13.9 mm (from Z=0.0 to Z=46.8).\n11. Finish turn diameter Ø37.3 mm over length 19.5 mm (from Z=0.0 to Z=32.9).\n12. Finish turn diameter Ø30.0 mm over length 13.4 mm (from Z=0.0 to Z=13.4).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00278
|
images/Shaft_00278.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø43.1 mm and length at least 256.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.1 mm over length 44.9 mm (from Z=0.0 to Z=44.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø34.6 mm over length 58.2 mm (from Z=0.0 to Z=206.6).\n10. Finish turn diameter Ø30.0 mm over length 148.4 mm (from Z=0.0 to Z=148.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00953
|
images/Shaft_00953.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø59.6 mm and length at least 163.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.6 mm over length 44.9 mm (from Z=0.0 to Z=44.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø42.9 mm over length 70.2 mm (from Z=0.0 to Z=114.0).\n9. Finish turn diameter Ø31.5 mm over length 43.8 mm (from Z=0.0 to Z=43.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00820
|
images/Shaft_00820.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø79.7 mm and length at least 170.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.7 mm over length 25.9 mm (from Z=0.0 to Z=25.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø74.7 mm over length 15.0 mm (from Z=0.0 to Z=140.0).\n9. Finish turn diameter Ø70.5 mm over length 47.1 mm (from Z=0.0 to Z=125.0).\n10. Finish turn diameter Ø55.5 mm over length 33.8 mm (from Z=0.0 to Z=77.9).\n11. Finish turn diameter Ø50.1 mm over length 44.1 mm (from Z=0.0 to Z=44.1).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00109
|
images/Shaft_00109.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø50.0 mm and length at least 262.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø48.0 mm over length 60.7 mm (from Z=0.0 to Z=60.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø48.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø42.2 mm over length 34.7 mm (from Z=0.0 to Z=197.2).\n10. Finish turn diameter Ø34.7 mm over length 90.1 mm (from Z=0.0 to Z=162.5).\n11. Finish turn diameter Ø30.0 mm over length 72.4 mm (from Z=0.0 to Z=72.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00118
|
images/Shaft_00118.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø57.6 mm and length at least 98.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø55.6 mm over length 16.9 mm (from Z=0.0 to Z=16.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø55.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø52.1 mm over length 21.8 mm (from Z=0.0 to Z=76.1).\n9. Finish turn diameter Ø44.1 mm over length 17.6 mm (from Z=0.0 to Z=54.3).\n10. Finish turn diameter Ø30.0 mm over length 36.7 mm (from Z=0.0 to Z=36.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00941
|
images/Shaft_00941.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø77.6 mm and length at least 298.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø75.6 mm over length 77.7 mm (from Z=0.0 to Z=77.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø75.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø71.4 mm over length 95.7 mm (from Z=0.0 to Z=216.1).\n10. Finish turn diameter Ø56.3 mm over length 91.3 mm (from Z=0.0 to Z=120.4).\n11. Finish turn diameter Ø50.1 mm over length 29.1 mm (from Z=0.0 to Z=29.1).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00137
|
images/Shaft_00137.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø67.7 mm and length at least 88.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.7 mm over length 33.3 mm (from Z=0.0 to Z=33.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø51.3 mm over length 9.4 mm (from Z=0.0 to Z=50.5).\n9. Finish turn diameter Ø43.9 mm over length 13.3 mm (from Z=0.0 to Z=41.1).\n10. Finish turn diameter Ø39.7 mm over length 19.2 mm (from Z=0.0 to Z=27.8).\n11. Finish turn diameter Ø30.0 mm over length 8.6 mm (from Z=0.0 to Z=8.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00106
|
images/Shaft_00106.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 177.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 159.2 mm (from Z=0.0 to Z=159.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø28.4 mm over length 13.4 mm (from Z=0.0 to Z=13.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00306
|
images/Shaft_00306.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø46.6 mm and length at least 319.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø44.6 mm over length 112.2 mm (from Z=0.0 to Z=112.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø44.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 202.5 mm (from Z=0.0 to Z=202.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00972
|
images/Shaft_00972.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø41.6 mm and length at least 95.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø39.6 mm over length 30.0 mm (from Z=0.0 to Z=30.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø39.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 60.4 mm (from Z=0.0 to Z=60.4).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00008
|
images/Shaft_00008.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø51.0 mm and length at least 322.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø49.0 mm over length 69.5 mm (from Z=0.0 to Z=69.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø49.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø45.4 mm over length 69.5 mm (from Z=0.0 to Z=247.8).\n10. Finish turn diameter Ø30.0 mm over length 178.3 mm (from Z=0.0 to Z=178.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00822
|
images/Shaft_00822.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø58.0 mm and length at least 217.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø56.0 mm over length 82.1 mm (from Z=0.0 to Z=82.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø56.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø43.8 mm over length 35.9 mm (from Z=0.0 to Z=129.9).\n10. Finish turn diameter Ø33.9 mm over length 60.3 mm (from Z=0.0 to Z=94.0).\n11. Finish turn diameter Ø30.0 mm over length 33.7 mm (from Z=0.0 to Z=33.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00309
|
images/Shaft_00309.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø57.7 mm and length at least 253.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø55.7 mm over length 22.1 mm (from Z=0.0 to Z=22.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø55.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø50.0 mm over length 29.3 mm (from Z=0.0 to Z=226.3).\n10. Finish turn diameter Ø40.8 mm over length 36.7 mm (from Z=0.0 to Z=197.0).\n11. Finish turn diameter Ø36.4 mm over length 59.1 mm (from Z=0.0 to Z=160.3).\n12. Finish turn diameter Ø30.0 mm over length 101.2 mm (from Z=0.0 to Z=101.2).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00556
|
images/Shaft_00556.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 133.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 100.0 mm (from Z=0.0 to Z=100.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø22.7 mm over length 28.9 mm (from Z=0.0 to Z=28.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00743
|
images/Shaft_00743.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø38.7 mm and length at least 302.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.7 mm over length 71.1 mm (from Z=0.0 to Z=71.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 226.4 mm (from Z=0.0 to Z=226.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00634
|
images/Shaft_00634.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø38.3 mm and length at least 123.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.3 mm over length 27.6 mm (from Z=0.0 to Z=27.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 91.2 mm (from Z=0.0 to Z=91.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00291
|
images/Shaft_00291.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø65.5 mm and length at least 271.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.5 mm over length 38.3 mm (from Z=0.0 to Z=38.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø47.7 mm over length 76.3 mm (from Z=0.0 to Z=227.9).\n10. Finish turn diameter Ø40.2 mm over length 132.8 mm (from Z=0.0 to Z=151.6).\n11. Finish turn diameter Ø37.0 mm over length 18.8 mm (from Z=0.0 to Z=18.8).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00378
|
images/Shaft_00378.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø76.5 mm and length at least 241.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø74.5 mm over length 19.1 mm (from Z=0.0 to Z=19.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø74.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø64.8 mm over length 59.1 mm (from Z=0.0 to Z=217.6).\n10. Finish turn diameter Ø45.5 mm over length 24.5 mm (from Z=0.0 to Z=158.5).\n11. Finish turn diameter Ø30.0 mm over length 134.0 mm (from Z=0.0 to Z=134.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00889
|
images/Shaft_00889.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø37.0 mm and length at least 203.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø35.0 mm over length 46.1 mm (from Z=0.0 to Z=46.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø35.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 152.1 mm (from Z=0.0 to Z=152.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00629
|
images/Shaft_00629.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø42.2 mm and length at least 151.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø40.2 mm over length 34.7 mm (from Z=0.0 to Z=34.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø40.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 111.8 mm (from Z=0.0 to Z=111.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00357
|
images/Shaft_00357.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø61.2 mm and length at least 201.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø59.2 mm over length 67.2 mm (from Z=0.0 to Z=67.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø59.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø40.7 mm over length 93.7 mm (from Z=0.0 to Z=129.2).\n10. Finish turn diameter Ø31.1 mm over length 35.5 mm (from Z=0.0 to Z=35.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00712
|
images/Shaft_00712.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 149.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 79.9 mm (from Z=0.0 to Z=79.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø25.8 mm over length 64.5 mm (from Z=0.0 to Z=64.5).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00620
|
images/Shaft_00620.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 68.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 45.3 mm (from Z=0.0 to Z=45.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø18.6 mm over length 18.1 mm (from Z=0.0 to Z=18.1).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00518
|
images/Shaft_00518.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 242.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 141.6 mm (from Z=0.0 to Z=141.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø23.8 mm over length 95.8 mm (from Z=0.0 to Z=95.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00662
|
images/Shaft_00662.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø79.3 mm and length at least 275.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.3 mm over length 74.5 mm (from Z=0.0 to Z=74.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø65.2 mm over length 41.2 mm (from Z=0.0 to Z=195.9).\n10. Finish turn diameter Ø51.6 mm over length 86.3 mm (from Z=0.0 to Z=154.7).\n11. Finish turn diameter Ø42.0 mm over length 68.4 mm (from Z=0.0 to Z=68.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00550
|
images/Shaft_00550.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø33.7 mm and length at least 127.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø31.7 mm over length 35.6 mm (from Z=0.0 to Z=35.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø31.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 86.6 mm (from Z=0.0 to Z=86.6).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00075
|
images/Shaft_00075.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø53.6 mm and length at least 153.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø51.6 mm over length 56.0 mm (from Z=0.0 to Z=56.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø51.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø35.4 mm over length 22.3 mm (from Z=0.0 to Z=92.7).\n9. Finish turn diameter Ø31.6 mm over length 14.5 mm (from Z=0.0 to Z=70.4).\n10. Finish turn diameter Ø30.0 mm over length 55.9 mm (from Z=0.0 to Z=55.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00102
|
images/Shaft_00102.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø64.0 mm and length at least 322.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø62.0 mm over length 36.7 mm (from Z=0.0 to Z=36.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø62.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø52.9 mm over length 26.1 mm (from Z=0.0 to Z=281.0).\n10. Finish turn diameter Ø44.6 mm over length 25.9 mm (from Z=0.0 to Z=254.9).\n11. Finish turn diameter Ø32.8 mm over length 107.9 mm (from Z=0.0 to Z=229.0).\n12. Finish turn diameter Ø30.0 mm over length 121.1 mm (from Z=0.0 to Z=121.1).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00576
|
images/Shaft_00576.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø43.9 mm and length at least 228.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.9 mm over length 53.9 mm (from Z=0.0 to Z=53.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 169.4 mm (from Z=0.0 to Z=169.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.