id
stringlengths 11
11
| image
stringlengths 22
22
| conversations
listlengths 2
2
|
|---|---|---|
Shaft_00686
|
images/Shaft_00686.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 72.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 53.5 mm (from Z=0.0 to Z=53.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø26.3 mm over length 13.7 mm (from Z=0.0 to Z=13.7).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00214
|
images/Shaft_00214.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø34.0 mm and length at least 73.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.0 mm over length 17.7 mm (from Z=0.0 to Z=17.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 51.2 mm (from Z=0.0 to Z=51.2).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00363
|
images/Shaft_00363.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø45.0 mm and length at least 150.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø43.0 mm over length 35.4 mm (from Z=0.0 to Z=35.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø43.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø33.4 mm over length 15.9 mm (from Z=0.0 to Z=109.8).\n10. Finish turn diameter Ø30.0 mm over length 93.9 mm (from Z=0.0 to Z=93.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00379
|
images/Shaft_00379.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø74.2 mm and length at least 201.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.2 mm over length 27.0 mm (from Z=0.0 to Z=27.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø57.5 mm over length 44.0 mm (from Z=0.0 to Z=169.8).\n10. Finish turn diameter Ø41.2 mm over length 40.1 mm (from Z=0.0 to Z=125.8).\n11. Finish turn diameter Ø30.0 mm over length 85.7 mm (from Z=0.0 to Z=85.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00166
|
images/Shaft_00166.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø57.5 mm and length at least 293.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø55.5 mm over length 35.0 mm (from Z=0.0 to Z=35.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø55.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø49.2 mm over length 25.2 mm (from Z=0.0 to Z=253.1).\n10. Finish turn diameter Ø33.5 mm over length 163.8 mm (from Z=0.0 to Z=227.9).\n11. Finish turn diameter Ø30.0 mm over length 64.1 mm (from Z=0.0 to Z=64.1).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00373
|
images/Shaft_00373.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø39.9 mm and length at least 298.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø37.9 mm over length 73.7 mm (from Z=0.0 to Z=73.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø37.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø31.2 mm over length 59.4 mm (from Z=0.0 to Z=220.1).\n10. Finish turn diameter Ø30.0 mm over length 160.7 mm (from Z=0.0 to Z=160.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00854
|
images/Shaft_00854.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø39.2 mm and length at least 196.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø37.2 mm over length 58.2 mm (from Z=0.0 to Z=58.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø37.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø32.4 mm over length 74.3 mm (from Z=0.0 to Z=133.3).\n10. Finish turn diameter Ø30.0 mm over length 59.0 mm (from Z=0.0 to Z=59.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00650
|
images/Shaft_00650.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø65.7 mm and length at least 150.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.7 mm over length 38.5 mm (from Z=0.0 to Z=38.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø52.3 mm over length 62.4 mm (from Z=0.0 to Z=106.8).\n9. Finish turn diameter Ø39.5 mm over length 44.4 mm (from Z=0.0 to Z=44.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00464
|
images/Shaft_00464.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø38.4 mm and length at least 71.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.4 mm over length 17.8 mm (from Z=0.0 to Z=17.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 49.1 mm (from Z=0.0 to Z=49.1).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00954
|
images/Shaft_00954.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 202.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 156.5 mm (from Z=0.0 to Z=156.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø19.8 mm over length 41.4 mm (from Z=0.0 to Z=41.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00947
|
images/Shaft_00947.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø45.4 mm and length at least 163.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø43.4 mm over length 23.9 mm (from Z=0.0 to Z=23.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø43.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø31.6 mm over length 37.0 mm (from Z=0.0 to Z=134.8).\n10. Finish turn diameter Ø30.0 mm over length 97.8 mm (from Z=0.0 to Z=97.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00103
|
images/Shaft_00103.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø48.8 mm and length at least 129.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø46.8 mm over length 5.0 mm (from Z=0.0 to Z=5.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø46.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø36.8 mm over length 32.5 mm (from Z=0.0 to Z=119.5).\n9. Finish turn diameter Ø31.5 mm over length 36.5 mm (from Z=0.0 to Z=87.0).\n10. Finish turn diameter Ø30.0 mm over length 50.5 mm (from Z=0.0 to Z=50.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00887
|
images/Shaft_00887.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.6 mm and length at least 150.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.6 mm over length 58.5 mm (from Z=0.0 to Z=58.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 87.4 mm (from Z=0.0 to Z=87.4).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00978
|
images/Shaft_00978.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.1 mm and length at least 278.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.1 mm over length 103.8 mm (from Z=0.0 to Z=103.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 169.9 mm (from Z=0.0 to Z=169.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00875
|
images/Shaft_00875.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø53.6 mm and length at least 228.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø51.6 mm over length 71.1 mm (from Z=0.0 to Z=71.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø51.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø34.5 mm over length 72.9 mm (from Z=0.0 to Z=152.8).\n10. Finish turn diameter Ø30.0 mm over length 79.9 mm (from Z=0.0 to Z=79.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00081
|
images/Shaft_00081.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø79.2 mm and length at least 194.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.2 mm over length 33.5 mm (from Z=0.0 to Z=33.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø64.5 mm over length 57.9 mm (from Z=0.0 to Z=156.0).\n9. Finish turn diameter Ø58.6 mm over length 81.3 mm (from Z=0.0 to Z=98.1).\n10. Finish turn diameter Ø55.0 mm over length 16.8 mm (from Z=0.0 to Z=16.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00296
|
images/Shaft_00296.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø34.3 mm and length at least 127.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.3 mm over length 29.9 mm (from Z=0.0 to Z=29.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 92.1 mm (from Z=0.0 to Z=92.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00791
|
images/Shaft_00791.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø73.3 mm and length at least 109.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø71.3 mm over length 28.4 mm (from Z=0.0 to Z=28.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø71.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø68.1 mm over length 6.5 mm (from Z=0.0 to Z=75.9).\n9. Finish turn diameter Ø48.8 mm over length 15.7 mm (from Z=0.0 to Z=69.4).\n10. Finish turn diameter Ø34.6 mm over length 5.0 mm (from Z=0.0 to Z=53.7).\n11. Finish turn diameter Ø30.0 mm over length 48.7 mm (from Z=0.0 to Z=48.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00233
|
images/Shaft_00233.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø55.7 mm and length at least 179.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.7 mm over length 67.3 mm (from Z=0.0 to Z=67.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø39.4 mm over length 89.9 mm (from Z=0.0 to Z=107.2).\n9. Finish turn diameter Ø30.0 mm over length 17.3 mm (from Z=0.0 to Z=17.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00677
|
images/Shaft_00677.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø43.1 mm and length at least 218.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.1 mm over length 41.2 mm (from Z=0.0 to Z=41.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 171.8 mm (from Z=0.0 to Z=171.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00046
|
images/Shaft_00046.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 143.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 123.7 mm (from Z=0.0 to Z=123.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø22.4 mm over length 14.3 mm (from Z=0.0 to Z=14.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00071
|
images/Shaft_00071.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø53.9 mm and length at least 117.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø51.9 mm over length 41.0 mm (from Z=0.0 to Z=41.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø51.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø41.3 mm over length 5.2 mm (from Z=0.0 to Z=71.2).\n9. Finish turn diameter Ø33.9 mm over length 5.0 mm (from Z=0.0 to Z=66.0).\n10. Finish turn diameter Ø30.0 mm over length 61.0 mm (from Z=0.0 to Z=61.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00721
|
images/Shaft_00721.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 279.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 217.9 mm (from Z=0.0 to Z=217.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø27.4 mm over length 56.6 mm (from Z=0.0 to Z=56.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00196
|
images/Shaft_00196.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 240.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 180.0 mm (from Z=0.0 to Z=180.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø22.8 mm over length 55.2 mm (from Z=0.0 to Z=55.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00591
|
images/Shaft_00591.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø73.8 mm and length at least 275.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø71.8 mm over length 43.9 mm (from Z=0.0 to Z=43.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø71.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø57.8 mm over length 71.0 mm (from Z=0.0 to Z=227.0).\n10. Finish turn diameter Ø44.5 mm over length 156.0 mm (from Z=0.0 to Z=156.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00370
|
images/Shaft_00370.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø66.1 mm and length at least 277.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø64.1 mm over length 18.6 mm (from Z=0.0 to Z=18.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø64.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø60.8 mm over length 45.1 mm (from Z=0.0 to Z=254.2).\n10. Finish turn diameter Ø45.5 mm over length 69.0 mm (from Z=0.0 to Z=209.1).\n11. Finish turn diameter Ø41.2 mm over length 86.2 mm (from Z=0.0 to Z=140.1).\n12. Finish turn diameter Ø34.9 mm over length 30.9 mm (from Z=0.0 to Z=53.9).\n13. Finish turn diameter Ø30.0 mm over length 23.0 mm (from Z=0.0 to Z=23.0).\n14. Break all edges (e.g., 2×45° where applicable).\n15. Remove the workpiece from the lathe."
}
] |
Shaft_00882
|
images/Shaft_00882.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø64.6 mm and length at least 263.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø62.6 mm over length 76.5 mm (from Z=0.0 to Z=76.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø62.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø54.4 mm over length 135.5 mm (from Z=0.0 to Z=181.8).\n10. Finish turn diameter Ø38.8 mm over length 46.3 mm (from Z=0.0 to Z=46.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00906
|
images/Shaft_00906.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø78.9 mm and length at least 187.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø76.9 mm over length 25.9 mm (from Z=0.0 to Z=25.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø76.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø63.6 mm over length 44.8 mm (from Z=0.0 to Z=156.8).\n9. Finish turn diameter Ø44.5 mm over length 22.7 mm (from Z=0.0 to Z=112.0).\n10. Finish turn diameter Ø35.1 mm over length 16.1 mm (from Z=0.0 to Z=89.3).\n11. Finish turn diameter Ø30.5 mm over length 73.2 mm (from Z=0.0 to Z=73.2).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00633
|
images/Shaft_00633.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø46.8 mm and length at least 249.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø44.8 mm over length 54.6 mm (from Z=0.0 to Z=54.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø44.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 190.3 mm (from Z=0.0 to Z=190.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00643
|
images/Shaft_00643.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø60.9 mm and length at least 207.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø58.9 mm over length 45.9 mm (from Z=0.0 to Z=45.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø58.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø52.6 mm over length 9.6 mm (from Z=0.0 to Z=156.6).\n10. Finish turn diameter Ø34.1 mm over length 38.9 mm (from Z=0.0 to Z=147.0).\n11. Finish turn diameter Ø30.0 mm over length 108.1 mm (from Z=0.0 to Z=108.1).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00849
|
images/Shaft_00849.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø68.0 mm and length at least 317.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø66.0 mm over length 106.3 mm (from Z=0.0 to Z=106.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø66.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø47.4 mm over length 25.0 mm (from Z=0.0 to Z=206.4).\n10. Finish turn diameter Ø31.7 mm over length 33.5 mm (from Z=0.0 to Z=181.4).\n11. Finish turn diameter Ø30.0 mm over length 147.9 mm (from Z=0.0 to Z=147.9).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00300
|
images/Shaft_00300.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø43.6 mm and length at least 101.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.6 mm over length 36.2 mm (from Z=0.0 to Z=36.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 60.3 mm (from Z=0.0 to Z=60.3).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00565
|
images/Shaft_00565.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø81.8 mm and length at least 298.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø79.8 mm over length 27.7 mm (from Z=0.0 to Z=27.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø79.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø62.6 mm over length 72.3 mm (from Z=0.0 to Z=265.4).\n10. Finish turn diameter Ø53.1 mm over length 94.5 mm (from Z=0.0 to Z=193.1).\n11. Finish turn diameter Ø43.3 mm over length 48.8 mm (from Z=0.0 to Z=98.6).\n12. Finish turn diameter Ø30.1 mm over length 49.8 mm (from Z=0.0 to Z=49.8).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00080
|
images/Shaft_00080.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø59.8 mm and length at least 269.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.8 mm over length 72.3 mm (from Z=0.0 to Z=72.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø48.4 mm over length 58.2 mm (from Z=0.0 to Z=192.6).\n10. Finish turn diameter Ø43.7 mm over length 69.7 mm (from Z=0.0 to Z=134.4).\n11. Finish turn diameter Ø35.2 mm over length 13.1 mm (from Z=0.0 to Z=64.7).\n12. Finish turn diameter Ø30.0 mm over length 51.6 mm (from Z=0.0 to Z=51.6).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00387
|
images/Shaft_00387.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø69.5 mm and length at least 171.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.5 mm over length 34.5 mm (from Z=0.0 to Z=34.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø54.6 mm over length 46.3 mm (from Z=0.0 to Z=132.4).\n9. Finish turn diameter Ø39.0 mm over length 9.7 mm (from Z=0.0 to Z=86.1).\n10. Finish turn diameter Ø33.4 mm over length 30.6 mm (from Z=0.0 to Z=76.4).\n11. Finish turn diameter Ø30.0 mm over length 45.8 mm (from Z=0.0 to Z=45.8).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00127
|
images/Shaft_00127.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø34.0 mm and length at least 241.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.0 mm over length 27.2 mm (from Z=0.0 to Z=27.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 209.4 mm (from Z=0.0 to Z=209.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00549
|
images/Shaft_00549.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø66.3 mm and length at least 164.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø64.3 mm over length 42.8 mm (from Z=0.0 to Z=42.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø64.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø50.3 mm over length 46.9 mm (from Z=0.0 to Z=116.3).\n9. Finish turn diameter Ø44.5 mm over length 50.2 mm (from Z=0.0 to Z=69.4).\n10. Finish turn diameter Ø30.0 mm over length 19.2 mm (from Z=0.0 to Z=19.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00470
|
images/Shaft_00470.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø38.4 mm and length at least 277.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.4 mm over length 42.1 mm (from Z=0.0 to Z=42.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 230.0 mm (from Z=0.0 to Z=230.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00747
|
images/Shaft_00747.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø79.6 mm and length at least 152.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.6 mm over length 20.5 mm (from Z=0.0 to Z=20.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø66.9 mm over length 45.1 mm (from Z=0.0 to Z=127.2).\n9. Finish turn diameter Ø55.1 mm over length 32.3 mm (from Z=0.0 to Z=82.1).\n10. Finish turn diameter Ø50.8 mm over length 49.8 mm (from Z=0.0 to Z=49.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00044
|
images/Shaft_00044.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø49.6 mm and length at least 148.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø47.6 mm over length 44.8 mm (from Z=0.0 to Z=44.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø47.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø44.3 mm over length 67.9 mm (from Z=0.0 to Z=98.7).\n9. Finish turn diameter Ø31.8 mm over length 30.8 mm (from Z=0.0 to Z=30.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00826
|
images/Shaft_00826.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø33.9 mm and length at least 169.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø31.9 mm over length 77.6 mm (from Z=0.0 to Z=77.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø31.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 87.2 mm (from Z=0.0 to Z=87.2).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00270
|
images/Shaft_00270.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø79.4 mm and length at least 284.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.4 mm over length 52.9 mm (from Z=0.0 to Z=52.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø68.0 mm over length 144.1 mm (from Z=0.0 to Z=226.4).\n10. Finish turn diameter Ø55.4 mm over length 82.3 mm (from Z=0.0 to Z=82.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00618
|
images/Shaft_00618.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø75.7 mm and length at least 317.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.7 mm over length 42.9 mm (from Z=0.0 to Z=42.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø68.7 mm over length 30.0 mm (from Z=0.0 to Z=269.9).\n10. Finish turn diameter Ø60.7 mm over length 68.9 mm (from Z=0.0 to Z=239.9).\n11. Finish turn diameter Ø55.4 mm over length 101.8 mm (from Z=0.0 to Z=171.0).\n12. Finish turn diameter Ø38.0 mm over length 69.2 mm (from Z=0.0 to Z=69.2).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00352
|
images/Shaft_00352.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø57.0 mm and length at least 165.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø55.0 mm over length 54.2 mm (from Z=0.0 to Z=54.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø55.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø35.5 mm over length 45.6 mm (from Z=0.0 to Z=106.6).\n9. Finish turn diameter Ø30.0 mm over length 61.0 mm (from Z=0.0 to Z=61.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00867
|
images/Shaft_00867.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 219.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 189.6 mm (from Z=0.0 to Z=189.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø29.7 mm over length 25.1 mm (from Z=0.0 to Z=25.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00367
|
images/Shaft_00367.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø67.0 mm and length at least 178.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.0 mm over length 27.6 mm (from Z=0.0 to Z=27.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø58.7 mm over length 43.0 mm (from Z=0.0 to Z=146.2).\n9. Finish turn diameter Ø49.0 mm over length 41.9 mm (from Z=0.0 to Z=103.2).\n10. Finish turn diameter Ø33.5 mm over length 61.3 mm (from Z=0.0 to Z=61.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00099
|
images/Shaft_00099.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø56.9 mm and length at least 159.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.9 mm over length 37.4 mm (from Z=0.0 to Z=37.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø35.4 mm over length 27.2 mm (from Z=0.0 to Z=116.8).\n9. Finish turn diameter Ø30.0 mm over length 89.6 mm (from Z=0.0 to Z=89.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00389
|
images/Shaft_00389.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø73.5 mm and length at least 242.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø71.5 mm over length 14.6 mm (from Z=0.0 to Z=14.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø71.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø54.4 mm over length 57.0 mm (from Z=0.0 to Z=222.8).\n10. Finish turn diameter Ø47.5 mm over length 38.6 mm (from Z=0.0 to Z=165.8).\n11. Finish turn diameter Ø38.1 mm over length 49.8 mm (from Z=0.0 to Z=127.2).\n12. Finish turn diameter Ø30.0 mm over length 77.4 mm (from Z=0.0 to Z=77.4).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00094
|
images/Shaft_00094.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø79.5 mm and length at least 263.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.5 mm over length 63.3 mm (from Z=0.0 to Z=63.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø64.7 mm over length 76.3 mm (from Z=0.0 to Z=195.1).\n10. Finish turn diameter Ø53.9 mm over length 72.8 mm (from Z=0.0 to Z=118.8).\n11. Finish turn diameter Ø36.0 mm over length 46.0 mm (from Z=0.0 to Z=46.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00990
|
images/Shaft_00990.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø55.6 mm and length at least 82.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.6 mm over length 14.7 mm (from Z=0.0 to Z=14.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø42.2 mm over length 7.0 mm (from Z=0.0 to Z=62.5).\n9. Finish turn diameter Ø37.4 mm over length 12.5 mm (from Z=0.0 to Z=55.5).\n10. Finish turn diameter Ø32.2 mm over length 14.2 mm (from Z=0.0 to Z=43.0).\n11. Finish turn diameter Ø30.0 mm over length 28.8 mm (from Z=0.0 to Z=28.8).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00344
|
images/Shaft_00344.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø72.0 mm and length at least 102.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø70.0 mm over length 24.5 mm (from Z=0.0 to Z=24.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø70.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø63.5 mm over length 41.8 mm (from Z=0.0 to Z=72.6).\n9. Finish turn diameter Ø56.7 mm over length 13.2 mm (from Z=0.0 to Z=30.8).\n10. Finish turn diameter Ø51.5 mm over length 17.6 mm (from Z=0.0 to Z=17.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00781
|
images/Shaft_00781.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø60.3 mm and length at least 76.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø58.3 mm over length 7.5 mm (from Z=0.0 to Z=7.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø58.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø42.4 mm over length 5.2 mm (from Z=0.0 to Z=64.0).\n9. Finish turn diameter Ø30.0 mm over length 58.8 mm (from Z=0.0 to Z=58.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00220
|
images/Shaft_00220.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø38.9 mm and length at least 281.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.9 mm over length 71.7 mm (from Z=0.0 to Z=71.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 205.0 mm (from Z=0.0 to Z=205.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00159
|
images/Shaft_00159.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø72.2 mm and length at least 211.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø70.2 mm over length 33.7 mm (from Z=0.0 to Z=33.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø70.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø53.7 mm over length 46.2 mm (from Z=0.0 to Z=172.4).\n10. Finish turn diameter Ø46.3 mm over length 52.5 mm (from Z=0.0 to Z=126.2).\n11. Finish turn diameter Ø40.7 mm over length 16.6 mm (from Z=0.0 to Z=73.7).\n12. Finish turn diameter Ø30.0 mm over length 57.1 mm (from Z=0.0 to Z=57.1).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00964
|
images/Shaft_00964.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 215.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 128.4 mm (from Z=0.0 to Z=128.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø20.1 mm over length 82.0 mm (from Z=0.0 to Z=82.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00348
|
images/Shaft_00348.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø78.4 mm and length at least 174.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø76.4 mm over length 72.5 mm (from Z=0.0 to Z=72.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø76.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø66.9 mm over length 42.3 mm (from Z=0.0 to Z=97.4).\n9. Finish turn diameter Ø57.4 mm over length 45.6 mm (from Z=0.0 to Z=55.1).\n10. Finish turn diameter Ø53.5 mm over length 9.5 mm (from Z=0.0 to Z=9.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00983
|
images/Shaft_00983.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø63.6 mm and length at least 301.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø61.6 mm over length 51.5 mm (from Z=0.0 to Z=51.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø61.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø45.4 mm over length 28.6 mm (from Z=0.0 to Z=245.3).\n10. Finish turn diameter Ø38.7 mm over length 17.1 mm (from Z=0.0 to Z=216.7).\n11. Finish turn diameter Ø30.0 mm over length 199.6 mm (from Z=0.0 to Z=199.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00714
|
images/Shaft_00714.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 223.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 167.9 mm (from Z=0.0 to Z=167.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø24.7 mm over length 50.5 mm (from Z=0.0 to Z=50.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00163
|
images/Shaft_00163.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø43.9 mm and length at least 280.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.9 mm over length 19.7 mm (from Z=0.0 to Z=19.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 256.2 mm (from Z=0.0 to Z=256.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00825
|
images/Shaft_00825.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø65.9 mm and length at least 301.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.9 mm over length 55.1 mm (from Z=0.0 to Z=55.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø54.4 mm over length 74.0 mm (from Z=0.0 to Z=241.0).\n10. Finish turn diameter Ø39.0 mm over length 30.6 mm (from Z=0.0 to Z=167.0).\n11. Finish turn diameter Ø30.0 mm over length 136.4 mm (from Z=0.0 to Z=136.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00777
|
images/Shaft_00777.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø75.7 mm and length at least 135.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.7 mm over length 31.2 mm (from Z=0.0 to Z=31.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø58.4 mm over length 10.0 mm (from Z=0.0 to Z=99.0).\n9. Finish turn diameter Ø40.3 mm over length 37.4 mm (from Z=0.0 to Z=89.0).\n10. Finish turn diameter Ø30.0 mm over length 51.6 mm (from Z=0.0 to Z=51.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00006
|
images/Shaft_00006.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø81.8 mm and length at least 167.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø79.8 mm over length 68.0 mm (from Z=0.0 to Z=68.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø79.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø64.7 mm over length 47.5 mm (from Z=0.0 to Z=94.3).\n9. Finish turn diameter Ø47.2 mm over length 46.8 mm (from Z=0.0 to Z=46.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00890
|
images/Shaft_00890.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 210.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 99.2 mm (from Z=0.0 to Z=99.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø29.7 mm over length 106.7 mm (from Z=0.0 to Z=106.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00828
|
images/Shaft_00828.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø50.8 mm and length at least 227.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø48.8 mm over length 16.2 mm (from Z=0.0 to Z=16.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø48.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø37.7 mm over length 56.2 mm (from Z=0.0 to Z=206.7).\n10. Finish turn diameter Ø30.0 mm over length 150.5 mm (from Z=0.0 to Z=150.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00284
|
images/Shaft_00284.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø35.5 mm and length at least 108.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.5 mm over length 32.6 mm (from Z=0.0 to Z=32.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 70.6 mm (from Z=0.0 to Z=70.6).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00603
|
images/Shaft_00603.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø78.6 mm and length at least 153.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø76.6 mm over length 57.3 mm (from Z=0.0 to Z=57.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø76.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø59.9 mm over length 45.1 mm (from Z=0.0 to Z=91.4).\n9. Finish turn diameter Ø54.2 mm over length 46.3 mm (from Z=0.0 to Z=46.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00459
|
images/Shaft_00459.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø80.2 mm and length at least 94.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.2 mm over length 27.0 mm (from Z=0.0 to Z=27.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø72.6 mm over length 28.1 mm (from Z=0.0 to Z=62.1).\n9. Finish turn diameter Ø54.9 mm over length 14.2 mm (from Z=0.0 to Z=34.0).\n10. Finish turn diameter Ø49.8 mm over length 19.8 mm (from Z=0.0 to Z=19.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00225
|
images/Shaft_00225.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø55.9 mm and length at least 108.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.9 mm over length 8.0 mm (from Z=0.0 to Z=8.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø43.6 mm over length 35.7 mm (from Z=0.0 to Z=95.1).\n9. Finish turn diameter Ø30.0 mm over length 59.4 mm (from Z=0.0 to Z=59.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00429
|
images/Shaft_00429.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø71.5 mm and length at least 275.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø69.5 mm over length 66.7 mm (from Z=0.0 to Z=66.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø69.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø65.2 mm over length 54.2 mm (from Z=0.0 to Z=203.6).\n10. Finish turn diameter Ø49.4 mm over length 73.9 mm (from Z=0.0 to Z=149.4).\n11. Finish turn diameter Ø36.3 mm over length 38.9 mm (from Z=0.0 to Z=75.5).\n12. Finish turn diameter Ø30.0 mm over length 36.6 mm (from Z=0.0 to Z=36.6).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00986
|
images/Shaft_00986.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø74.4 mm and length at least 190.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.4 mm over length 80.7 mm (from Z=0.0 to Z=80.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø63.5 mm over length 53.9 mm (from Z=0.0 to Z=105.0).\n9. Finish turn diameter Ø54.4 mm over length 51.1 mm (from Z=0.0 to Z=51.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00718
|
images/Shaft_00718.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 324.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 230.0 mm (from Z=0.0 to Z=230.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø18.3 mm over length 89.2 mm (from Z=0.0 to Z=89.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00665
|
images/Shaft_00665.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø66.4 mm and length at least 107.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø64.4 mm over length 50.7 mm (from Z=0.0 to Z=50.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø64.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø60.9 mm over length 5.0 mm (from Z=0.0 to Z=52.2).\n9. Finish turn diameter Ø41.6 mm over length 47.2 mm (from Z=0.0 to Z=47.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00733
|
images/Shaft_00733.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø65.7 mm and length at least 115.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.7 mm over length 16.2 mm (from Z=0.0 to Z=16.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø55.5 mm over length 13.3 mm (from Z=0.0 to Z=94.7).\n9. Finish turn diameter Ø50.9 mm over length 15.1 mm (from Z=0.0 to Z=81.4).\n10. Finish turn diameter Ø43.7 mm over length 29.7 mm (from Z=0.0 to Z=66.3).\n11. Finish turn diameter Ø30.0 mm over length 36.6 mm (from Z=0.0 to Z=36.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00203
|
images/Shaft_00203.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø38.4 mm and length at least 215.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.4 mm over length 60.0 mm (from Z=0.0 to Z=60.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø31.8 mm over length 65.4 mm (from Z=0.0 to Z=150.1).\n10. Finish turn diameter Ø30.0 mm over length 84.7 mm (from Z=0.0 to Z=84.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00574
|
images/Shaft_00574.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø65.4 mm and length at least 323.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.4 mm over length 91.3 mm (from Z=0.0 to Z=91.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø57.5 mm over length 64.1 mm (from Z=0.0 to Z=227.1).\n10. Finish turn diameter Ø52.5 mm over length 51.4 mm (from Z=0.0 to Z=163.0).\n11. Finish turn diameter Ø43.9 mm over length 45.9 mm (from Z=0.0 to Z=111.6).\n12. Finish turn diameter Ø35.7 mm over length 65.7 mm (from Z=0.0 to Z=65.7).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00027
|
images/Shaft_00027.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø43.7 mm and length at least 263.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.7 mm over length 50.9 mm (from Z=0.0 to Z=50.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø34.3 mm over length 46.7 mm (from Z=0.0 to Z=207.3).\n10. Finish turn diameter Ø30.0 mm over length 160.6 mm (from Z=0.0 to Z=160.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00616
|
images/Shaft_00616.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 221.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 173.2 mm (from Z=0.0 to Z=173.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø18.4 mm over length 43.4 mm (from Z=0.0 to Z=43.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00517
|
images/Shaft_00517.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø47.8 mm and length at least 208.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø45.8 mm over length 11.5 mm (from Z=0.0 to Z=11.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø45.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 192.0 mm (from Z=0.0 to Z=192.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00238
|
images/Shaft_00238.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø53.2 mm and length at least 117.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø51.2 mm over length 23.7 mm (from Z=0.0 to Z=23.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø51.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø35.2 mm over length 26.0 mm (from Z=0.0 to Z=88.9).\n9. Finish turn diameter Ø30.9 mm over length 21.3 mm (from Z=0.0 to Z=62.9).\n10. Finish turn diameter Ø30.0 mm over length 41.6 mm (from Z=0.0 to Z=41.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00223
|
images/Shaft_00223.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø34.9 mm and length at least 143.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.9 mm over length 25.2 mm (from Z=0.0 to Z=25.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 113.4 mm (from Z=0.0 to Z=113.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00095
|
images/Shaft_00095.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø80.2 mm and length at least 163.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.2 mm over length 50.0 mm (from Z=0.0 to Z=50.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø63.3 mm over length 10.9 mm (from Z=0.0 to Z=108.4).\n9. Finish turn diameter Ø46.4 mm over length 46.7 mm (from Z=0.0 to Z=97.5).\n10. Finish turn diameter Ø38.5 mm over length 50.8 mm (from Z=0.0 to Z=50.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00030
|
images/Shaft_00030.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø63.3 mm and length at least 161.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø61.3 mm over length 25.8 mm (from Z=0.0 to Z=25.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø61.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø42.9 mm over length 58.4 mm (from Z=0.0 to Z=130.3).\n9. Finish turn diameter Ø33.1 mm over length 71.9 mm (from Z=0.0 to Z=71.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00032
|
images/Shaft_00032.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø71.2 mm and length at least 95.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø69.2 mm over length 23.6 mm (from Z=0.0 to Z=23.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø69.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø65.5 mm over length 16.2 mm (from Z=0.0 to Z=66.4).\n9. Finish turn diameter Ø60.0 mm over length 18.3 mm (from Z=0.0 to Z=50.2).\n10. Finish turn diameter Ø51.1 mm over length 5.2 mm (from Z=0.0 to Z=31.9).\n11. Finish turn diameter Ø46.4 mm over length 26.7 mm (from Z=0.0 to Z=26.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00432
|
images/Shaft_00432.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø73.4 mm and length at least 146.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø71.4 mm over length 11.5 mm (from Z=0.0 to Z=11.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø71.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø64.7 mm over length 16.3 mm (from Z=0.0 to Z=129.6).\n9. Finish turn diameter Ø59.6 mm over length 35.7 mm (from Z=0.0 to Z=113.3).\n10. Finish turn diameter Ø46.8 mm over length 33.0 mm (from Z=0.0 to Z=77.6).\n11. Finish turn diameter Ø31.1 mm over length 16.7 mm (from Z=0.0 to Z=44.6).\n12. Finish turn diameter Ø30.0 mm over length 27.9 mm (from Z=0.0 to Z=27.9).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00604
|
images/Shaft_00604.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø69.7 mm and length at least 115.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.7 mm over length 18.7 mm (from Z=0.0 to Z=18.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø63.7 mm over length 12.3 mm (from Z=0.0 to Z=92.0).\n9. Finish turn diameter Ø59.9 mm over length 31.2 mm (from Z=0.0 to Z=79.7).\n10. Finish turn diameter Ø55.4 mm over length 25.2 mm (from Z=0.0 to Z=48.5).\n11. Finish turn diameter Ø49.6 mm over length 5.0 mm (from Z=0.0 to Z=23.3).\n12. Finish turn diameter Ø40.1 mm over length 18.3 mm (from Z=0.0 to Z=18.3).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00089
|
images/Shaft_00089.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø40.3 mm and length at least 112.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø38.3 mm over length 31.5 mm (from Z=0.0 to Z=31.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø38.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 75.9 mm (from Z=0.0 to Z=75.9).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00558
|
images/Shaft_00558.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø57.2 mm and length at least 97.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø55.2 mm over length 20.5 mm (from Z=0.0 to Z=20.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø55.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø51.6 mm over length 12.1 mm (from Z=0.0 to Z=72.2).\n9. Finish turn diameter Ø40.6 mm over length 51.7 mm (from Z=0.0 to Z=60.1).\n10. Finish turn diameter Ø30.0 mm over length 8.4 mm (from Z=0.0 to Z=8.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00913
|
images/Shaft_00913.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø60.9 mm and length at least 311.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø58.9 mm over length 61.7 mm (from Z=0.0 to Z=61.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø58.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø44.2 mm over length 58.6 mm (from Z=0.0 to Z=244.4).\n10. Finish turn diameter Ø30.0 mm over length 185.8 mm (from Z=0.0 to Z=185.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00758
|
images/Shaft_00758.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø78.5 mm and length at least 235.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø76.5 mm over length 27.7 mm (from Z=0.0 to Z=27.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø76.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø68.4 mm over length 62.9 mm (from Z=0.0 to Z=203.2).\n10. Finish turn diameter Ø49.0 mm over length 18.7 mm (from Z=0.0 to Z=140.3).\n11. Finish turn diameter Ø40.5 mm over length 44.5 mm (from Z=0.0 to Z=121.6).\n12. Finish turn diameter Ø30.0 mm over length 77.1 mm (from Z=0.0 to Z=77.1).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00692
|
images/Shaft_00692.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø70.0 mm and length at least 251.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø68.0 mm over length 9.8 mm (from Z=0.0 to Z=9.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø68.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø62.3 mm over length 39.7 mm (from Z=0.0 to Z=237.1).\n10. Finish turn diameter Ø49.2 mm over length 52.1 mm (from Z=0.0 to Z=197.4).\n11. Finish turn diameter Ø31.0 mm over length 39.0 mm (from Z=0.0 to Z=145.3).\n12. Finish turn diameter Ø30.0 mm over length 106.3 mm (from Z=0.0 to Z=106.3).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00104
|
images/Shaft_00104.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø65.2 mm and length at least 247.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.2 mm over length 30.6 mm (from Z=0.0 to Z=30.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø59.4 mm over length 33.8 mm (from Z=0.0 to Z=211.8).\n10. Finish turn diameter Ø45.0 mm over length 105.0 mm (from Z=0.0 to Z=178.0).\n11. Finish turn diameter Ø32.7 mm over length 73.0 mm (from Z=0.0 to Z=73.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00754
|
images/Shaft_00754.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 141.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 119.1 mm (from Z=0.0 to Z=119.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø27.4 mm over length 17.4 mm (from Z=0.0 to Z=17.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00142
|
images/Shaft_00142.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø41.4 mm and length at least 215.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø39.4 mm over length 56.9 mm (from Z=0.0 to Z=56.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø39.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 153.7 mm (from Z=0.0 to Z=153.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00228
|
images/Shaft_00228.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø60.3 mm and length at least 126.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø58.3 mm over length 26.5 mm (from Z=0.0 to Z=26.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø58.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø47.5 mm over length 47.2 mm (from Z=0.0 to Z=94.9).\n9. Finish turn diameter Ø30.3 mm over length 47.7 mm (from Z=0.0 to Z=47.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00250
|
images/Shaft_00250.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 292.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 254.2 mm (from Z=0.0 to Z=254.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø27.3 mm over length 33.5 mm (from Z=0.0 to Z=33.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00281
|
images/Shaft_00281.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø56.5 mm and length at least 250.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.5 mm over length 13.1 mm (from Z=0.0 to Z=13.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø41.4 mm over length 107.2 mm (from Z=0.0 to Z=232.5).\n10. Finish turn diameter Ø34.5 mm over length 106.2 mm (from Z=0.0 to Z=125.3).\n11. Finish turn diameter Ø30.0 mm over length 19.1 mm (from Z=0.0 to Z=19.1).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00759
|
images/Shaft_00759.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 77.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 43.8 mm (from Z=0.0 to Z=43.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø27.1 mm over length 28.9 mm (from Z=0.0 to Z=28.9).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00025
|
images/Shaft_00025.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø47.3 mm and length at least 109.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø45.3 mm over length 15.7 mm (from Z=0.0 to Z=15.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø45.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 88.8 mm (from Z=0.0 to Z=88.8).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00114
|
images/Shaft_00114.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø36.6 mm and length at least 71.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø34.6 mm over length 25.6 mm (from Z=0.0 to Z=25.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø34.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 40.5 mm (from Z=0.0 to Z=40.5).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00654
|
images/Shaft_00654.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 159.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 100.1 mm (from Z=0.0 to Z=100.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø23.6 mm over length 54.5 mm (from Z=0.0 to Z=54.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.