id
stringlengths 11
11
| image
stringlengths 22
22
| conversations
listlengths 2
2
|
|---|---|---|
Shaft_00930
|
images/Shaft_00930.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø53.1 mm and length at least 180.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø51.1 mm over length 55.2 mm (from Z=0.0 to Z=55.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø51.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø46.2 mm over length 19.7 mm (from Z=0.0 to Z=120.2).\n9. Finish turn diameter Ø31.5 mm over length 76.8 mm (from Z=0.0 to Z=100.5).\n10. Finish turn diameter Ø30.0 mm over length 23.7 mm (from Z=0.0 to Z=23.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00736
|
images/Shaft_00736.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø75.6 mm and length at least 70.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.6 mm over length 10.7 mm (from Z=0.0 to Z=10.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø70.0 mm over length 7.5 mm (from Z=0.0 to Z=54.4).\n9. Finish turn diameter Ø66.3 mm over length 10.2 mm (from Z=0.0 to Z=46.9).\n10. Finish turn diameter Ø57.6 mm over length 7.3 mm (from Z=0.0 to Z=36.7).\n11. Finish turn diameter Ø42.1 mm over length 15.0 mm (from Z=0.0 to Z=29.4).\n12. Finish turn diameter Ø32.6 mm over length 14.4 mm (from Z=0.0 to Z=14.4).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00739
|
images/Shaft_00739.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø36.3 mm and length at least 252.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø34.3 mm over length 158.3 mm (from Z=0.0 to Z=158.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø34.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 89.5 mm (from Z=0.0 to Z=89.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00003
|
images/Shaft_00003.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø39.3 mm and length at least 249.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø37.3 mm over length 59.8 mm (from Z=0.0 to Z=59.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø37.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 185.1 mm (from Z=0.0 to Z=185.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00908
|
images/Shaft_00908.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø47.9 mm and length at least 112.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø45.9 mm over length 22.8 mm (from Z=0.0 to Z=22.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø45.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø42.6 mm over length 8.9 mm (from Z=0.0 to Z=84.5).\n9. Finish turn diameter Ø30.0 mm over length 75.6 mm (from Z=0.0 to Z=75.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00161
|
images/Shaft_00161.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø35.0 mm and length at least 123.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.0 mm over length 57.5 mm (from Z=0.0 to Z=57.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 61.0 mm (from Z=0.0 to Z=61.0).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00445
|
images/Shaft_00445.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø59.8 mm and length at least 139.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.8 mm over length 66.6 mm (from Z=0.0 to Z=66.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø46.1 mm over length 50.6 mm (from Z=0.0 to Z=67.8).\n9. Finish turn diameter Ø38.3 mm over length 17.2 mm (from Z=0.0 to Z=17.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00931
|
images/Shaft_00931.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø42.1 mm and length at least 284.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø40.1 mm over length 77.4 mm (from Z=0.0 to Z=77.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø40.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 202.0 mm (from Z=0.0 to Z=202.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00998
|
images/Shaft_00998.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø40.4 mm and length at least 312.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø38.4 mm over length 37.0 mm (from Z=0.0 to Z=37.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø38.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 270.4 mm (from Z=0.0 to Z=270.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00955
|
images/Shaft_00955.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø74.4 mm and length at least 80.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.4 mm over length 11.8 mm (from Z=0.0 to Z=11.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø59.3 mm over length 33.8 mm (from Z=0.0 to Z=63.5).\n9. Finish turn diameter Ø44.2 mm over length 29.7 mm (from Z=0.0 to Z=29.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00656
|
images/Shaft_00656.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø34.8 mm and length at least 249.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.8 mm over length 56.7 mm (from Z=0.0 to Z=56.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 187.7 mm (from Z=0.0 to Z=187.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00787
|
images/Shaft_00787.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø40.3 mm and length at least 120.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø38.3 mm over length 42.1 mm (from Z=0.0 to Z=42.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø38.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø34.3 mm over length 5.6 mm (from Z=0.0 to Z=73.3).\n9. Finish turn diameter Ø30.0 mm over length 67.7 mm (from Z=0.0 to Z=67.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00899
|
images/Shaft_00899.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø81.9 mm and length at least 77.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø79.9 mm over length 12.6 mm (from Z=0.0 to Z=12.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø79.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø63.1 mm over length 22.8 mm (from Z=0.0 to Z=60.0).\n9. Finish turn diameter Ø55.7 mm over length 11.4 mm (from Z=0.0 to Z=37.2).\n10. Finish turn diameter Ø51.8 mm over length 20.1 mm (from Z=0.0 to Z=25.8).\n11. Finish turn diameter Ø40.1 mm over length 5.7 mm (from Z=0.0 to Z=5.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00768
|
images/Shaft_00768.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø63.7 mm and length at least 93.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø61.7 mm over length 26.3 mm (from Z=0.0 to Z=26.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø61.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø51.6 mm over length 18.6 mm (from Z=0.0 to Z=62.0).\n9. Finish turn diameter Ø46.8 mm over length 31.3 mm (from Z=0.0 to Z=43.4).\n10. Finish turn diameter Ø34.2 mm over length 12.1 mm (from Z=0.0 to Z=12.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00936
|
images/Shaft_00936.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø58.0 mm and length at least 209.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø56.0 mm over length 46.4 mm (from Z=0.0 to Z=46.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø56.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø41.5 mm over length 45.1 mm (from Z=0.0 to Z=157.7).\n10. Finish turn diameter Ø35.6 mm over length 24.8 mm (from Z=0.0 to Z=112.6).\n11. Finish turn diameter Ø30.0 mm over length 87.8 mm (from Z=0.0 to Z=87.8).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00698
|
images/Shaft_00698.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø79.9 mm and length at least 231.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.9 mm over length 37.6 mm (from Z=0.0 to Z=37.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø59.6 mm over length 40.1 mm (from Z=0.0 to Z=188.5).\n10. Finish turn diameter Ø40.3 mm over length 24.7 mm (from Z=0.0 to Z=148.4).\n11. Finish turn diameter Ø30.0 mm over length 123.7 mm (from Z=0.0 to Z=123.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00117
|
images/Shaft_00117.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø80.7 mm and length at least 153.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.7 mm over length 16.5 mm (from Z=0.0 to Z=16.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø69.9 mm over length 37.7 mm (from Z=0.0 to Z=131.5).\n9. Finish turn diameter Ø58.9 mm over length 40.3 mm (from Z=0.0 to Z=93.8).\n10. Finish turn diameter Ø50.3 mm over length 33.4 mm (from Z=0.0 to Z=53.5).\n11. Finish turn diameter Ø32.1 mm over length 5.1 mm (from Z=0.0 to Z=20.1).\n12. Finish turn diameter Ø30.0 mm over length 15.0 mm (from Z=0.0 to Z=15.0).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00738
|
images/Shaft_00738.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø41.1 mm and length at least 264.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø39.1 mm over length 139.5 mm (from Z=0.0 to Z=139.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø39.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 119.9 mm (from Z=0.0 to Z=119.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00830
|
images/Shaft_00830.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø54.8 mm and length at least 171.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø52.8 mm over length 51.7 mm (from Z=0.0 to Z=51.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø52.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø38.4 mm over length 51.7 mm (from Z=0.0 to Z=115.2).\n9. Finish turn diameter Ø30.0 mm over length 63.5 mm (from Z=0.0 to Z=63.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00011
|
images/Shaft_00011.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø37.0 mm and length at least 262.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø35.0 mm over length 67.9 mm (from Z=0.0 to Z=67.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø35.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 189.2 mm (from Z=0.0 to Z=189.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00566
|
images/Shaft_00566.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø78.7 mm and length at least 78.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø76.7 mm over length 20.1 mm (from Z=0.0 to Z=20.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø76.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø64.1 mm over length 17.8 mm (from Z=0.0 to Z=53.0).\n9. Finish turn diameter Ø45.4 mm over length 15.8 mm (from Z=0.0 to Z=35.2).\n10. Finish turn diameter Ø34.4 mm over length 14.4 mm (from Z=0.0 to Z=19.4).\n11. Finish turn diameter Ø30.0 mm over length 5.0 mm (from Z=0.0 to Z=5.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00257
|
images/Shaft_00257.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø61.0 mm and length at least 215.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø59.0 mm over length 55.7 mm (from Z=0.0 to Z=55.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø59.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø41.3 mm over length 21.1 mm (from Z=0.0 to Z=154.7).\n10. Finish turn diameter Ø35.7 mm over length 85.2 mm (from Z=0.0 to Z=133.6).\n11. Finish turn diameter Ø30.0 mm over length 48.4 mm (from Z=0.0 to Z=48.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00541
|
images/Shaft_00541.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø42.0 mm and length at least 132.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø40.0 mm over length 15.1 mm (from Z=0.0 to Z=15.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø40.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø34.6 mm over length 25.9 mm (from Z=0.0 to Z=112.8).\n9. Finish turn diameter Ø30.0 mm over length 86.9 mm (from Z=0.0 to Z=86.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00479
|
images/Shaft_00479.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 231.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 123.6 mm (from Z=0.0 to Z=123.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø27.9 mm over length 102.9 mm (from Z=0.0 to Z=102.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00963
|
images/Shaft_00963.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø75.9 mm and length at least 271.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.9 mm over length 74.5 mm (from Z=0.0 to Z=74.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø58.0 mm over length 25.1 mm (from Z=0.0 to Z=192.2).\n10. Finish turn diameter Ø48.4 mm over length 72.2 mm (from Z=0.0 to Z=167.1).\n11. Finish turn diameter Ø38.5 mm over length 34.2 mm (from Z=0.0 to Z=94.9).\n12. Finish turn diameter Ø30.0 mm over length 60.7 mm (from Z=0.0 to Z=60.7).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00390
|
images/Shaft_00390.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø64.6 mm and length at least 273.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø62.6 mm over length 132.2 mm (from Z=0.0 to Z=132.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø62.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø45.1 mm over length 23.4 mm (from Z=0.0 to Z=136.3).\n10. Finish turn diameter Ø34.1 mm over length 46.6 mm (from Z=0.0 to Z=112.9).\n11. Finish turn diameter Ø30.0 mm over length 66.3 mm (from Z=0.0 to Z=66.3).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00394
|
images/Shaft_00394.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø48.4 mm and length at least 227.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø46.4 mm over length 114.1 mm (from Z=0.0 to Z=114.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø46.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø35.4 mm over length 46.8 mm (from Z=0.0 to Z=108.3).\n10. Finish turn diameter Ø30.0 mm over length 61.5 mm (from Z=0.0 to Z=61.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00065
|
images/Shaft_00065.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 176.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 157.7 mm (from Z=0.0 to Z=157.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø23.0 mm over length 13.5 mm (from Z=0.0 to Z=13.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00610
|
images/Shaft_00610.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 216.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 168.4 mm (from Z=0.0 to Z=168.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø20.5 mm over length 43.4 mm (from Z=0.0 to Z=43.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00956
|
images/Shaft_00956.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø79.9 mm and length at least 127.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.9 mm over length 31.6 mm (from Z=0.0 to Z=31.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø72.5 mm over length 33.7 mm (from Z=0.0 to Z=91.3).\n9. Finish turn diameter Ø68.2 mm over length 5.7 mm (from Z=0.0 to Z=57.6).\n10. Finish turn diameter Ø58.3 mm over length 31.2 mm (from Z=0.0 to Z=51.9).\n11. Finish turn diameter Ø47.0 mm over length 5.5 mm (from Z=0.0 to Z=20.7).\n12. Finish turn diameter Ø37.3 mm over length 15.2 mm (from Z=0.0 to Z=15.2).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00696
|
images/Shaft_00696.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø56.3 mm and length at least 173.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.3 mm over length 20.7 mm (from Z=0.0 to Z=20.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.5 mm over length 28.4 mm (from Z=0.0 to Z=148.2).\n10. Finish turn diameter Ø30.0 mm over length 119.8 mm (from Z=0.0 to Z=119.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00811
|
images/Shaft_00811.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 262.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 193.4 mm (from Z=0.0 to Z=193.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø21.7 mm over length 64.5 mm (from Z=0.0 to Z=64.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00958
|
images/Shaft_00958.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø65.2 mm and length at least 303.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.2 mm over length 45.4 mm (from Z=0.0 to Z=45.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø54.6 mm over length 142.7 mm (from Z=0.0 to Z=253.3).\n10. Finish turn diameter Ø40.7 mm over length 50.5 mm (from Z=0.0 to Z=110.6).\n11. Finish turn diameter Ø32.0 mm over length 22.8 mm (from Z=0.0 to Z=60.1).\n12. Finish turn diameter Ø30.0 mm over length 37.3 mm (from Z=0.0 to Z=37.3).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00642
|
images/Shaft_00642.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.5 mm and length at least 70.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.5 mm over length 12.5 mm (from Z=0.0 to Z=12.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 52.6 mm (from Z=0.0 to Z=52.6).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00156
|
images/Shaft_00156.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø55.9 mm and length at least 281.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.9 mm over length 55.8 mm (from Z=0.0 to Z=55.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø41.9 mm over length 24.3 mm (from Z=0.0 to Z=220.2).\n10. Finish turn diameter Ø30.0 mm over length 195.9 mm (from Z=0.0 to Z=195.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00112
|
images/Shaft_00112.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø58.8 mm and length at least 156.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø56.8 mm over length 19.5 mm (from Z=0.0 to Z=19.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø56.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø47.3 mm over length 55.9 mm (from Z=0.0 to Z=131.8).\n9. Finish turn diameter Ø30.0 mm over length 75.9 mm (from Z=0.0 to Z=75.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00048
|
images/Shaft_00048.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.5 mm and length at least 157.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.5 mm over length 14.0 mm (from Z=0.0 to Z=14.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 138.9 mm (from Z=0.0 to Z=138.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00773
|
images/Shaft_00773.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø44.0 mm and length at least 311.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø42.0 mm over length 19.1 mm (from Z=0.0 to Z=19.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø42.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø33.6 mm over length 50.4 mm (from Z=0.0 to Z=287.3).\n10. Finish turn diameter Ø30.0 mm over length 236.9 mm (from Z=0.0 to Z=236.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00093
|
images/Shaft_00093.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø80.5 mm and length at least 116.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.5 mm over length 5.0 mm (from Z=0.0 to Z=5.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø64.7 mm over length 28.1 mm (from Z=0.0 to Z=106.7).\n9. Finish turn diameter Ø52.3 mm over length 24.8 mm (from Z=0.0 to Z=78.6).\n10. Finish turn diameter Ø43.4 mm over length 5.0 mm (from Z=0.0 to Z=53.8).\n11. Finish turn diameter Ø35.2 mm over length 24.4 mm (from Z=0.0 to Z=48.8).\n12. Finish turn diameter Ø30.0 mm over length 24.4 mm (from Z=0.0 to Z=24.4).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00505
|
images/Shaft_00505.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø70.7 mm and length at least 253.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø68.7 mm over length 47.9 mm (from Z=0.0 to Z=47.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø68.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø62.5 mm over length 27.1 mm (from Z=0.0 to Z=200.6).\n10. Finish turn diameter Ø42.8 mm over length 27.2 mm (from Z=0.0 to Z=173.5).\n11. Finish turn diameter Ø30.4 mm over length 69.0 mm (from Z=0.0 to Z=146.3).\n12. Finish turn diameter Ø30.0 mm over length 77.3 mm (from Z=0.0 to Z=77.3).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00521
|
images/Shaft_00521.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø72.4 mm and length at least 82.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø70.4 mm over length 22.7 mm (from Z=0.0 to Z=22.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø70.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø67.2 mm over length 6.7 mm (from Z=0.0 to Z=54.3).\n9. Finish turn diameter Ø54.1 mm over length 14.1 mm (from Z=0.0 to Z=47.6).\n10. Finish turn diameter Ø36.5 mm over length 7.9 mm (from Z=0.0 to Z=33.5).\n11. Finish turn diameter Ø32.7 mm over length 20.6 mm (from Z=0.0 to Z=25.6).\n12. Finish turn diameter Ø30.0 mm over length 5.0 mm (from Z=0.0 to Z=5.0).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00141
|
images/Shaft_00141.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø75.2 mm and length at least 197.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.2 mm over length 65.7 mm (from Z=0.0 to Z=65.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø57.7 mm over length 63.4 mm (from Z=0.0 to Z=126.5).\n10. Finish turn diameter Ø44.4 mm over length 41.6 mm (from Z=0.0 to Z=63.1).\n11. Finish turn diameter Ø40.4 mm over length 21.5 mm (from Z=0.0 to Z=21.5).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00881
|
images/Shaft_00881.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 289.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 220.2 mm (from Z=0.0 to Z=220.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø28.7 mm over length 64.1 mm (from Z=0.0 to Z=64.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00925
|
images/Shaft_00925.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø68.0 mm and length at least 150.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø66.0 mm over length 20.4 mm (from Z=0.0 to Z=20.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø66.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø53.6 mm over length 34.2 mm (from Z=0.0 to Z=124.9).\n9. Finish turn diameter Ø35.7 mm over length 22.2 mm (from Z=0.0 to Z=90.7).\n10. Finish turn diameter Ø30.0 mm over length 68.5 mm (from Z=0.0 to Z=68.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00408
|
images/Shaft_00408.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø59.5 mm and length at least 181.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.5 mm over length 48.6 mm (from Z=0.0 to Z=48.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø43.9 mm over length 29.7 mm (from Z=0.0 to Z=128.1).\n10. Finish turn diameter Ø30.0 mm over length 98.4 mm (from Z=0.0 to Z=98.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00597
|
images/Shaft_00597.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 223.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 188.9 mm (from Z=0.0 to Z=188.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø29.8 mm over length 29.5 mm (from Z=0.0 to Z=29.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00438
|
images/Shaft_00438.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø77.8 mm and length at least 317.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø75.8 mm over length 125.0 mm (from Z=0.0 to Z=125.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø75.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø57.9 mm over length 104.0 mm (from Z=0.0 to Z=187.0).\n10. Finish turn diameter Ø43.7 mm over length 83.0 mm (from Z=0.0 to Z=83.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00598
|
images/Shaft_00598.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø56.9 mm and length at least 192.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.9 mm over length 46.8 mm (from Z=0.0 to Z=46.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø51.6 mm over length 67.9 mm (from Z=0.0 to Z=140.2).\n9. Finish turn diameter Ø34.4 mm over length 27.9 mm (from Z=0.0 to Z=72.3).\n10. Finish turn diameter Ø30.0 mm over length 44.4 mm (from Z=0.0 to Z=44.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00764
|
images/Shaft_00764.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 204.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 166.3 mm (from Z=0.0 to Z=166.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø23.4 mm over length 33.4 mm (from Z=0.0 to Z=33.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00269
|
images/Shaft_00269.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø80.4 mm and length at least 242.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.4 mm over length 94.6 mm (from Z=0.0 to Z=94.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø60.9 mm over length 52.4 mm (from Z=0.0 to Z=142.9).\n10. Finish turn diameter Ø41.9 mm over length 90.5 mm (from Z=0.0 to Z=90.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00551
|
images/Shaft_00551.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 110.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 92.4 mm (from Z=0.0 to Z=92.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø29.0 mm over length 13.4 mm (from Z=0.0 to Z=13.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00974
|
images/Shaft_00974.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø61.3 mm and length at least 84.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø59.3 mm over length 6.9 mm (from Z=0.0 to Z=6.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø59.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø51.2 mm over length 20.9 mm (from Z=0.0 to Z=72.5).\n9. Finish turn diameter Ø34.9 mm over length 51.6 mm (from Z=0.0 to Z=51.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00762
|
images/Shaft_00762.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø63.9 mm and length at least 245.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø61.9 mm over length 56.3 mm (from Z=0.0 to Z=56.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø61.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø57.1 mm over length 55.9 mm (from Z=0.0 to Z=184.3).\n10. Finish turn diameter Ø47.3 mm over length 42.0 mm (from Z=0.0 to Z=128.4).\n11. Finish turn diameter Ø35.9 mm over length 51.4 mm (from Z=0.0 to Z=86.4).\n12. Finish turn diameter Ø30.0 mm over length 35.0 mm (from Z=0.0 to Z=35.0).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00252
|
images/Shaft_00252.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø64.2 mm and length at least 137.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø62.2 mm over length 19.5 mm (from Z=0.0 to Z=19.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø62.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø55.3 mm over length 13.9 mm (from Z=0.0 to Z=113.4).\n9. Finish turn diameter Ø36.0 mm over length 21.0 mm (from Z=0.0 to Z=99.5).\n10. Finish turn diameter Ø31.8 mm over length 13.9 mm (from Z=0.0 to Z=78.5).\n11. Finish turn diameter Ø30.0 mm over length 64.6 mm (from Z=0.0 to Z=64.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00992
|
images/Shaft_00992.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø38.5 mm and length at least 207.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.5 mm over length 44.4 mm (from Z=0.0 to Z=44.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 158.5 mm (from Z=0.0 to Z=158.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00271
|
images/Shaft_00271.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø51.2 mm and length at least 142.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø49.2 mm over length 53.8 mm (from Z=0.0 to Z=53.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø49.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø31.6 mm over length 27.1 mm (from Z=0.0 to Z=83.8).\n9. Finish turn diameter Ø30.0 mm over length 56.7 mm (from Z=0.0 to Z=56.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00146
|
images/Shaft_00146.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø76.7 mm and length at least 191.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø74.7 mm over length 17.3 mm (from Z=0.0 to Z=17.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø74.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø59.3 mm over length 35.7 mm (from Z=0.0 to Z=169.6).\n9. Finish turn diameter Ø45.9 mm over length 40.2 mm (from Z=0.0 to Z=133.9).\n10. Finish turn diameter Ø34.0 mm over length 19.1 mm (from Z=0.0 to Z=93.7).\n11. Finish turn diameter Ø30.0 mm over length 74.6 mm (from Z=0.0 to Z=74.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00469
|
images/Shaft_00469.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø71.1 mm and length at least 269.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø69.1 mm over length 75.3 mm (from Z=0.0 to Z=75.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø69.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø52.0 mm over length 56.8 mm (from Z=0.0 to Z=188.8).\n10. Finish turn diameter Ø41.9 mm over length 51.9 mm (from Z=0.0 to Z=132.0).\n11. Finish turn diameter Ø30.0 mm over length 80.1 mm (from Z=0.0 to Z=80.1).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00658
|
images/Shaft_00658.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 72.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 40.9 mm (from Z=0.0 to Z=40.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø22.0 mm over length 26.6 mm (from Z=0.0 to Z=26.6).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00405
|
images/Shaft_00405.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø35.0 mm and length at least 318.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.0 mm over length 64.2 mm (from Z=0.0 to Z=64.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 249.2 mm (from Z=0.0 to Z=249.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00511
|
images/Shaft_00511.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø36.8 mm and length at least 251.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø34.8 mm over length 105.0 mm (from Z=0.0 to Z=105.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø34.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 141.2 mm (from Z=0.0 to Z=141.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00671
|
images/Shaft_00671.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø62.8 mm and length at least 273.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø60.8 mm over length 43.8 mm (from Z=0.0 to Z=43.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø60.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø44.1 mm over length 30.8 mm (from Z=0.0 to Z=225.1).\n10. Finish turn diameter Ø30.0 mm over length 194.3 mm (from Z=0.0 to Z=194.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00217
|
images/Shaft_00217.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø68.2 mm and length at least 236.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø66.2 mm over length 30.0 mm (from Z=0.0 to Z=30.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø66.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø54.5 mm over length 78.8 mm (from Z=0.0 to Z=201.4).\n10. Finish turn diameter Ø49.9 mm over length 74.6 mm (from Z=0.0 to Z=122.6).\n11. Finish turn diameter Ø44.8 mm over length 48.0 mm (from Z=0.0 to Z=48.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00322
|
images/Shaft_00322.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø61.9 mm and length at least 288.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø59.9 mm over length 20.4 mm (from Z=0.0 to Z=20.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø59.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø54.8 mm over length 119.7 mm (from Z=0.0 to Z=262.6).\n10. Finish turn diameter Ø37.6 mm over length 110.3 mm (from Z=0.0 to Z=142.9).\n11. Finish turn diameter Ø32.2 mm over length 32.6 mm (from Z=0.0 to Z=32.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00735
|
images/Shaft_00735.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø47.4 mm and length at least 76.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø45.4 mm over length 12.0 mm (from Z=0.0 to Z=12.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø45.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø36.9 mm over length 18.4 mm (from Z=0.0 to Z=59.8).\n9. Finish turn diameter Ø30.4 mm over length 41.4 mm (from Z=0.0 to Z=41.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00580
|
images/Shaft_00580.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø47.6 mm and length at least 246.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø45.6 mm over length 33.2 mm (from Z=0.0 to Z=33.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø45.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø36.9 mm over length 54.3 mm (from Z=0.0 to Z=208.6).\n10. Finish turn diameter Ø30.0 mm over length 154.3 mm (from Z=0.0 to Z=154.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00216
|
images/Shaft_00216.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø59.2 mm and length at least 283.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.2 mm over length 32.1 mm (from Z=0.0 to Z=32.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø52.9 mm over length 63.2 mm (from Z=0.0 to Z=246.0).\n10. Finish turn diameter Ø41.3 mm over length 89.9 mm (from Z=0.0 to Z=182.8).\n11. Finish turn diameter Ø30.0 mm over length 92.9 mm (from Z=0.0 to Z=92.9).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00067
|
images/Shaft_00067.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 169.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 141.0 mm (from Z=0.0 to Z=141.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø25.4 mm over length 23.5 mm (from Z=0.0 to Z=23.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00274
|
images/Shaft_00274.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø51.9 mm and length at least 225.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø49.9 mm over length 102.4 mm (from Z=0.0 to Z=102.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø49.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.3 mm over length 53.1 mm (from Z=0.0 to Z=118.3).\n10. Finish turn diameter Ø30.0 mm over length 65.2 mm (from Z=0.0 to Z=65.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00410
|
images/Shaft_00410.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø38.2 mm and length at least 198.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.2 mm over length 14.9 mm (from Z=0.0 to Z=14.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 178.9 mm (from Z=0.0 to Z=178.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00323
|
images/Shaft_00323.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø71.3 mm and length at least 205.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø69.3 mm over length 97.8 mm (from Z=0.0 to Z=97.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø69.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø61.9 mm over length 70.6 mm (from Z=0.0 to Z=102.9).\n10. Finish turn diameter Ø45.0 mm over length 32.3 mm (from Z=0.0 to Z=32.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00824
|
images/Shaft_00824.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø61.0 mm and length at least 170.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø59.0 mm over length 29.2 mm (from Z=0.0 to Z=29.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø59.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø55.4 mm over length 49.0 mm (from Z=0.0 to Z=136.4).\n9. Finish turn diameter Ø49.2 mm over length 18.8 mm (from Z=0.0 to Z=87.4).\n10. Finish turn diameter Ø30.0 mm over length 68.6 mm (from Z=0.0 to Z=68.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00982
|
images/Shaft_00982.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø81.9 mm and length at least 145.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø79.9 mm over length 35.7 mm (from Z=0.0 to Z=35.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø79.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø68.8 mm over length 33.4 mm (from Z=0.0 to Z=104.6).\n9. Finish turn diameter Ø54.4 mm over length 29.8 mm (from Z=0.0 to Z=71.2).\n10. Finish turn diameter Ø39.2 mm over length 41.4 mm (from Z=0.0 to Z=41.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00841
|
images/Shaft_00841.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø81.0 mm and length at least 223.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø79.0 mm over length 29.5 mm (from Z=0.0 to Z=29.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø79.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø74.6 mm over length 61.0 mm (from Z=0.0 to Z=189.4).\n10. Finish turn diameter Ø70.7 mm over length 44.9 mm (from Z=0.0 to Z=128.4).\n11. Finish turn diameter Ø55.3 mm over length 39.4 mm (from Z=0.0 to Z=83.5).\n12. Finish turn diameter Ø51.6 mm over length 44.1 mm (from Z=0.0 to Z=44.1).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00234
|
images/Shaft_00234.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø38.0 mm and length at least 174.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.0 mm over length 25.2 mm (from Z=0.0 to Z=25.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 144.6 mm (from Z=0.0 to Z=144.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00057
|
images/Shaft_00057.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 323.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 213.2 mm (from Z=0.0 to Z=213.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø27.6 mm over length 105.5 mm (from Z=0.0 to Z=105.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00794
|
images/Shaft_00794.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 244.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 174.1 mm (from Z=0.0 to Z=174.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø26.5 mm over length 65.1 mm (from Z=0.0 to Z=65.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00786
|
images/Shaft_00786.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 72.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 32.3 mm (from Z=0.0 to Z=32.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø21.9 mm over length 35.1 mm (from Z=0.0 to Z=35.1).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00863
|
images/Shaft_00863.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 88.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 38.0 mm (from Z=0.0 to Z=38.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø19.9 mm over length 45.5 mm (from Z=0.0 to Z=45.5).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00332
|
images/Shaft_00332.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø41.8 mm and length at least 105.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø39.8 mm over length 5.0 mm (from Z=0.0 to Z=5.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø39.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø31.2 mm over length 37.4 mm (from Z=0.0 to Z=95.6).\n9. Finish turn diameter Ø30.0 mm over length 58.2 mm (from Z=0.0 to Z=58.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00701
|
images/Shaft_00701.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø75.1 mm and length at least 272.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.1 mm over length 44.4 mm (from Z=0.0 to Z=44.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø70.0 mm over length 113.6 mm (from Z=0.0 to Z=222.8).\n10. Finish turn diameter Ø59.4 mm over length 109.2 mm (from Z=0.0 to Z=109.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00224
|
images/Shaft_00224.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø51.4 mm and length at least 307.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø49.4 mm over length 71.9 mm (from Z=0.0 to Z=71.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø49.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.6 mm over length 76.6 mm (from Z=0.0 to Z=230.5).\n10. Finish turn diameter Ø30.0 mm over length 153.9 mm (from Z=0.0 to Z=153.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00570
|
images/Shaft_00570.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø67.8 mm and length at least 141.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.8 mm over length 38.4 mm (from Z=0.0 to Z=38.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø56.6 mm over length 23.6 mm (from Z=0.0 to Z=97.9).\n9. Finish turn diameter Ø49.2 mm over length 74.3 mm (from Z=0.0 to Z=74.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00704
|
images/Shaft_00704.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 317.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 243.5 mm (from Z=0.0 to Z=243.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø24.7 mm over length 69.1 mm (from Z=0.0 to Z=69.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00655
|
images/Shaft_00655.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø68.6 mm and length at least 250.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø66.6 mm over length 35.2 mm (from Z=0.0 to Z=35.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø66.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø61.3 mm over length 86.3 mm (from Z=0.0 to Z=210.3).\n10. Finish turn diameter Ø53.4 mm over length 20.9 mm (from Z=0.0 to Z=124.0).\n11. Finish turn diameter Ø49.7 mm over length 46.3 mm (from Z=0.0 to Z=103.1).\n12. Finish turn diameter Ø45.6 mm over length 19.4 mm (from Z=0.0 to Z=56.8).\n13. Finish turn diameter Ø32.6 mm over length 37.4 mm (from Z=0.0 to Z=37.4).\n14. Break all edges (e.g., 2×45° where applicable).\n15. Remove the workpiece from the lathe."
}
] |
Shaft_00276
|
images/Shaft_00276.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 166.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 113.7 mm (from Z=0.0 to Z=113.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø25.6 mm over length 47.7 mm (from Z=0.0 to Z=47.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00388
|
images/Shaft_00388.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø45.3 mm and length at least 148.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø43.3 mm over length 7.3 mm (from Z=0.0 to Z=7.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø43.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø39.2 mm over length 34.8 mm (from Z=0.0 to Z=135.7).\n10. Finish turn diameter Ø30.0 mm over length 100.9 mm (from Z=0.0 to Z=100.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00473
|
images/Shaft_00473.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø52.2 mm and length at least 195.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø50.2 mm over length 33.4 mm (from Z=0.0 to Z=33.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø50.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.3 mm over length 43.1 mm (from Z=0.0 to Z=156.6).\n10. Finish turn diameter Ø30.0 mm over length 113.5 mm (from Z=0.0 to Z=113.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00167
|
images/Shaft_00167.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø58.4 mm and length at least 181.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø56.4 mm over length 23.0 mm (from Z=0.0 to Z=23.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø56.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.7 mm over length 13.8 mm (from Z=0.0 to Z=153.9).\n10. Finish turn diameter Ø30.0 mm over length 140.1 mm (from Z=0.0 to Z=140.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00994
|
images/Shaft_00994.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø70.2 mm and length at least 257.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø68.2 mm over length 88.2 mm (from Z=0.0 to Z=88.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø68.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø52.0 mm over length 67.8 mm (from Z=0.0 to Z=164.6).\n10. Finish turn diameter Ø48.6 mm over length 96.8 mm (from Z=0.0 to Z=96.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00746
|
images/Shaft_00746.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.4 mm and length at least 268.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.4 mm over length 124.8 mm (from Z=0.0 to Z=124.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 138.8 mm (from Z=0.0 to Z=138.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00546
|
images/Shaft_00546.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø51.6 mm and length at least 153.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø49.6 mm over length 45.7 mm (from Z=0.0 to Z=45.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø49.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø32.1 mm over length 34.6 mm (from Z=0.0 to Z=102.8).\n9. Finish turn diameter Ø30.0 mm over length 68.2 mm (from Z=0.0 to Z=68.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00175
|
images/Shaft_00175.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø43.7 mm and length at least 133.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.7 mm over length 47.1 mm (from Z=0.0 to Z=47.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 81.4 mm (from Z=0.0 to Z=81.4).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00907
|
images/Shaft_00907.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø55.0 mm and length at least 128.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.0 mm over length 26.6 mm (from Z=0.0 to Z=26.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø34.5 mm over length 12.9 mm (from Z=0.0 to Z=97.0).\n9. Finish turn diameter Ø30.0 mm over length 84.1 mm (from Z=0.0 to Z=84.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00623
|
images/Shaft_00623.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø37.9 mm and length at least 164.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø35.9 mm over length 57.8 mm (from Z=0.0 to Z=57.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø35.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 101.4 mm (from Z=0.0 to Z=101.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00073
|
images/Shaft_00073.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø63.9 mm and length at least 264.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø61.9 mm over length 65.6 mm (from Z=0.0 to Z=65.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø61.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø54.5 mm over length 109.7 mm (from Z=0.0 to Z=194.2).\n10. Finish turn diameter Ø39.6 mm over length 84.5 mm (from Z=0.0 to Z=84.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00663
|
images/Shaft_00663.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø72.0 mm and length at least 210.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø70.0 mm over length 83.9 mm (from Z=0.0 to Z=83.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø70.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø62.2 mm over length 69.7 mm (from Z=0.0 to Z=121.3).\n10. Finish turn diameter Ø47.6 mm over length 51.6 mm (from Z=0.0 to Z=51.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00699
|
images/Shaft_00699.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø75.8 mm and length at least 180.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.8 mm over length 40.3 mm (from Z=0.0 to Z=40.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø63.2 mm over length 32.9 mm (from Z=0.0 to Z=134.8).\n9. Finish turn diameter Ø54.5 mm over length 43.9 mm (from Z=0.0 to Z=101.9).\n10. Finish turn diameter Ø49.4 mm over length 16.4 mm (from Z=0.0 to Z=58.0).\n11. Finish turn diameter Ø31.7 mm over length 41.6 mm (from Z=0.0 to Z=41.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00970
|
images/Shaft_00970.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø54.3 mm and length at least 93.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø52.3 mm over length 19.9 mm (from Z=0.0 to Z=19.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø52.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø33.4 mm over length 13.9 mm (from Z=0.0 to Z=68.6).\n9. Finish turn diameter Ø30.0 mm over length 54.7 mm (from Z=0.0 to Z=54.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00273
|
images/Shaft_00273.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø73.2 mm and length at least 238.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø71.2 mm over length 16.0 mm (from Z=0.0 to Z=16.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø71.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø65.4 mm over length 77.0 mm (from Z=0.0 to Z=217.7).\n10. Finish turn diameter Ø58.4 mm over length 16.7 mm (from Z=0.0 to Z=140.7).\n11. Finish turn diameter Ø44.0 mm over length 49.2 mm (from Z=0.0 to Z=124.0).\n12. Finish turn diameter Ø30.5 mm over length 51.6 mm (from Z=0.0 to Z=74.8).\n13. Finish turn diameter Ø30.0 mm over length 23.2 mm (from Z=0.0 to Z=23.2).\n14. Break all edges (e.g., 2×45° where applicable).\n15. Remove the workpiece from the lathe."
}
] |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.