id
stringlengths 11
11
| image
stringlengths 22
22
| conversations
listlengths 2
2
|
|---|---|---|
Shaft_00031
|
images/Shaft_00031.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø34.3 mm and length at least 212.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.3 mm over length 45.7 mm (from Z=0.0 to Z=45.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 162.1 mm (from Z=0.0 to Z=162.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00579
|
images/Shaft_00579.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.9 mm and length at least 299.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.9 mm over length 125.2 mm (from Z=0.0 to Z=125.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 169.7 mm (from Z=0.0 to Z=169.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00404
|
images/Shaft_00404.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 76.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 65.0 mm (from Z=0.0 to Z=65.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø18.4 mm over length 6.9 mm (from Z=0.0 to Z=6.9).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00277
|
images/Shaft_00277.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø72.5 mm and length at least 79.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø70.5 mm over length 27.3 mm (from Z=0.0 to Z=27.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø70.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø65.1 mm over length 19.2 mm (from Z=0.0 to Z=46.9).\n9. Finish turn diameter Ø61.5 mm over length 6.3 mm (from Z=0.0 to Z=27.7).\n10. Finish turn diameter Ø54.6 mm over length 5.0 mm (from Z=0.0 to Z=21.4).\n11. Finish turn diameter Ø40.5 mm over length 16.4 mm (from Z=0.0 to Z=16.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00444
|
images/Shaft_00444.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 274.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 172.4 mm (from Z=0.0 to Z=172.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø23.6 mm over length 97.0 mm (from Z=0.0 to Z=97.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00771
|
images/Shaft_00771.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø48.5 mm and length at least 190.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø46.5 mm over length 45.3 mm (from Z=0.0 to Z=45.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø46.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø32.1 mm over length 30.1 mm (from Z=0.0 to Z=140.1).\n10. Finish turn diameter Ø30.0 mm over length 110.0 mm (from Z=0.0 to Z=110.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00372
|
images/Shaft_00372.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.7 mm and length at least 305.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.7 mm over length 152.9 mm (from Z=0.0 to Z=152.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 147.3 mm (from Z=0.0 to Z=147.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00722
|
images/Shaft_00722.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø67.3 mm and length at least 91.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.3 mm over length 27.2 mm (from Z=0.0 to Z=27.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø51.9 mm over length 5.0 mm (from Z=0.0 to Z=59.5).\n9. Finish turn diameter Ø41.6 mm over length 17.7 mm (from Z=0.0 to Z=54.5).\n10. Finish turn diameter Ø30.0 mm over length 36.8 mm (from Z=0.0 to Z=36.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00400
|
images/Shaft_00400.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø34.6 mm and length at least 180.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.6 mm over length 15.9 mm (from Z=0.0 to Z=15.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 159.7 mm (from Z=0.0 to Z=159.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00078
|
images/Shaft_00078.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø48.5 mm and length at least 169.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø46.5 mm over length 44.7 mm (from Z=0.0 to Z=44.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø46.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø39.8 mm over length 69.4 mm (from Z=0.0 to Z=119.9).\n9. Finish turn diameter Ø30.0 mm over length 50.5 mm (from Z=0.0 to Z=50.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00537
|
images/Shaft_00537.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø35.2 mm and length at least 96.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.2 mm over length 13.8 mm (from Z=0.0 to Z=13.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 77.8 mm (from Z=0.0 to Z=77.8).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00575
|
images/Shaft_00575.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø77.4 mm and length at least 285.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø75.4 mm over length 27.7 mm (from Z=0.0 to Z=27.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø75.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø67.6 mm over length 8.4 mm (from Z=0.0 to Z=252.9).\n10. Finish turn diameter Ø58.6 mm over length 73.5 mm (from Z=0.0 to Z=244.5).\n11. Finish turn diameter Ø45.1 mm over length 44.7 mm (from Z=0.0 to Z=171.0).\n12. Finish turn diameter Ø30.0 mm over length 126.3 mm (from Z=0.0 to Z=126.3).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00548
|
images/Shaft_00548.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø70.7 mm and length at least 261.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø68.7 mm over length 41.9 mm (from Z=0.0 to Z=41.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø68.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø58.6 mm over length 58.7 mm (from Z=0.0 to Z=214.2).\n10. Finish turn diameter Ø46.1 mm over length 45.5 mm (from Z=0.0 to Z=155.5).\n11. Finish turn diameter Ø36.8 mm over length 110.0 mm (from Z=0.0 to Z=110.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00710
|
images/Shaft_00710.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø50.5 mm and length at least 215.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø48.5 mm over length 34.9 mm (from Z=0.0 to Z=34.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø48.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø40.0 mm over length 33.6 mm (from Z=0.0 to Z=175.3).\n10. Finish turn diameter Ø35.4 mm over length 40.8 mm (from Z=0.0 to Z=141.7).\n11. Finish turn diameter Ø30.7 mm over length 100.9 mm (from Z=0.0 to Z=100.9).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00041
|
images/Shaft_00041.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø42.5 mm and length at least 122.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø40.5 mm over length 25.0 mm (from Z=0.0 to Z=25.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø40.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø32.9 mm over length 18.4 mm (from Z=0.0 to Z=92.0).\n9. Finish turn diameter Ø30.0 mm over length 73.6 mm (from Z=0.0 to Z=73.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00885
|
images/Shaft_00885.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø33.7 mm and length at least 215.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø31.7 mm over length 22.0 mm (from Z=0.0 to Z=22.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø31.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 188.5 mm (from Z=0.0 to Z=188.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00632
|
images/Shaft_00632.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø35.9 mm and length at least 315.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.9 mm over length 144.1 mm (from Z=0.0 to Z=144.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 166.8 mm (from Z=0.0 to Z=166.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00858
|
images/Shaft_00858.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø46.5 mm and length at least 247.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø44.5 mm over length 60.0 mm (from Z=0.0 to Z=60.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø44.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø37.0 mm over length 18.7 mm (from Z=0.0 to Z=182.9).\n10. Finish turn diameter Ø30.0 mm over length 164.2 mm (from Z=0.0 to Z=164.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00139
|
images/Shaft_00139.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø47.3 mm and length at least 95.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø45.3 mm over length 32.6 mm (from Z=0.0 to Z=32.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø45.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø33.7 mm over length 21.5 mm (from Z=0.0 to Z=57.5).\n9. Finish turn diameter Ø30.0 mm over length 36.0 mm (from Z=0.0 to Z=36.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00385
|
images/Shaft_00385.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø73.7 mm and length at least 209.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø71.7 mm over length 31.6 mm (from Z=0.0 to Z=31.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø71.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø66.7 mm over length 42.3 mm (from Z=0.0 to Z=173.0).\n10. Finish turn diameter Ø52.8 mm over length 28.2 mm (from Z=0.0 to Z=130.7).\n11. Finish turn diameter Ø37.6 mm over length 49.3 mm (from Z=0.0 to Z=102.5).\n12. Finish turn diameter Ø30.0 mm over length 53.2 mm (from Z=0.0 to Z=53.2).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00456
|
images/Shaft_00456.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 258.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 172.4 mm (from Z=0.0 to Z=172.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø26.3 mm over length 80.9 mm (from Z=0.0 to Z=80.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00932
|
images/Shaft_00932.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø55.4 mm and length at least 181.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.4 mm over length 24.7 mm (from Z=0.0 to Z=24.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø34.7 mm over length 42.8 mm (from Z=0.0 to Z=151.9).\n10. Finish turn diameter Ø30.0 mm over length 109.1 mm (from Z=0.0 to Z=109.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00813
|
images/Shaft_00813.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø33.1 mm and length at least 217.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø31.1 mm over length 41.6 mm (from Z=0.0 to Z=41.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø31.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 170.9 mm (from Z=0.0 to Z=170.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00140
|
images/Shaft_00140.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø80.7 mm and length at least 283.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.7 mm over length 12.2 mm (from Z=0.0 to Z=12.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø73.8 mm over length 25.8 mm (from Z=0.0 to Z=266.1).\n10. Finish turn diameter Ø67.6 mm over length 69.2 mm (from Z=0.0 to Z=240.3).\n11. Finish turn diameter Ø56.3 mm over length 72.4 mm (from Z=0.0 to Z=171.1).\n12. Finish turn diameter Ø41.6 mm over length 48.2 mm (from Z=0.0 to Z=98.7).\n13. Finish turn diameter Ø32.8 mm over length 50.5 mm (from Z=0.0 to Z=50.5).\n14. Break all edges (e.g., 2×45° where applicable).\n15. Remove the workpiece from the lathe."
}
] |
Shaft_00624
|
images/Shaft_00624.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø72.3 mm and length at least 112.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø70.3 mm over length 11.1 mm (from Z=0.0 to Z=11.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø70.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø64.7 mm over length 36.9 mm (from Z=0.0 to Z=96.5).\n9. Finish turn diameter Ø55.1 mm over length 5.5 mm (from Z=0.0 to Z=59.6).\n10. Finish turn diameter Ø48.8 mm over length 18.8 mm (from Z=0.0 to Z=54.1).\n11. Finish turn diameter Ø40.2 mm over length 6.0 mm (from Z=0.0 to Z=35.3).\n12. Finish turn diameter Ø30.0 mm over length 29.3 mm (from Z=0.0 to Z=29.3).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00320
|
images/Shaft_00320.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø79.7 mm and length at least 130.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.7 mm over length 20.3 mm (from Z=0.0 to Z=20.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø63.3 mm over length 49.0 mm (from Z=0.0 to Z=105.3).\n9. Finish turn diameter Ø56.9 mm over length 7.9 mm (from Z=0.0 to Z=56.3).\n10. Finish turn diameter Ø51.9 mm over length 28.7 mm (from Z=0.0 to Z=48.4).\n11. Finish turn diameter Ø33.4 mm over length 19.7 mm (from Z=0.0 to Z=19.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00708
|
images/Shaft_00708.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø57.3 mm and length at least 231.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø55.3 mm over length 74.9 mm (from Z=0.0 to Z=74.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø55.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø37.8 mm over length 25.1 mm (from Z=0.0 to Z=151.2).\n10. Finish turn diameter Ø30.0 mm over length 126.1 mm (from Z=0.0 to Z=126.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00457
|
images/Shaft_00457.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø74.5 mm and length at least 270.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.5 mm over length 127.7 mm (from Z=0.0 to Z=127.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø60.7 mm over length 42.7 mm (from Z=0.0 to Z=137.6).\n10. Finish turn diameter Ø42.5 mm over length 94.9 mm (from Z=0.0 to Z=94.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00873
|
images/Shaft_00873.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 106.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 76.0 mm (from Z=0.0 to Z=76.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø25.1 mm over length 25.2 mm (from Z=0.0 to Z=25.2).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00326
|
images/Shaft_00326.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø77.2 mm and length at least 228.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø75.2 mm over length 94.9 mm (from Z=0.0 to Z=94.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø75.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø70.5 mm over length 93.8 mm (from Z=0.0 to Z=129.0).\n10. Finish turn diameter Ø56.8 mm over length 22.3 mm (from Z=0.0 to Z=35.2).\n11. Finish turn diameter Ø51.1 mm over length 12.9 mm (from Z=0.0 to Z=12.9).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00126
|
images/Shaft_00126.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø73.5 mm and length at least 292.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø71.5 mm over length 123.1 mm (from Z=0.0 to Z=123.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø71.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø56.7 mm over length 82.9 mm (from Z=0.0 to Z=164.8).\n10. Finish turn diameter Ø52.0 mm over length 81.9 mm (from Z=0.0 to Z=81.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00132
|
images/Shaft_00132.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø76.8 mm and length at least 305.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø74.8 mm over length 91.6 mm (from Z=0.0 to Z=91.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø74.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø62.7 mm over length 8.5 mm (from Z=0.0 to Z=208.6).\n10. Finish turn diameter Ø51.4 mm over length 10.5 mm (from Z=0.0 to Z=200.1).\n11. Finish turn diameter Ø33.3 mm over length 37.6 mm (from Z=0.0 to Z=189.6).\n12. Finish turn diameter Ø30.0 mm over length 152.0 mm (from Z=0.0 to Z=152.0).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00817
|
images/Shaft_00817.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø47.4 mm and length at least 269.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø45.4 mm over length 94.0 mm (from Z=0.0 to Z=94.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø45.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø36.4 mm over length 39.2 mm (from Z=0.0 to Z=170.9).\n10. Finish turn diameter Ø30.0 mm over length 131.7 mm (from Z=0.0 to Z=131.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00397
|
images/Shaft_00397.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø64.9 mm and length at least 143.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø62.9 mm over length 50.2 mm (from Z=0.0 to Z=50.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø62.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø46.4 mm over length 25.9 mm (from Z=0.0 to Z=88.0).\n9. Finish turn diameter Ø30.0 mm over length 62.1 mm (from Z=0.0 to Z=62.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00915
|
images/Shaft_00915.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø60.5 mm and length at least 241.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø58.5 mm over length 49.1 mm (from Z=0.0 to Z=49.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø58.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø42.0 mm over length 22.9 mm (from Z=0.0 to Z=187.2).\n10. Finish turn diameter Ø38.7 mm over length 22.1 mm (from Z=0.0 to Z=164.3).\n11. Finish turn diameter Ø30.0 mm over length 142.2 mm (from Z=0.0 to Z=142.2).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00993
|
images/Shaft_00993.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø76.3 mm and length at least 264.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø74.3 mm over length 15.9 mm (from Z=0.0 to Z=15.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø74.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø69.5 mm over length 57.8 mm (from Z=0.0 to Z=243.3).\n10. Finish turn diameter Ø66.2 mm over length 32.0 mm (from Z=0.0 to Z=185.5).\n11. Finish turn diameter Ø56.9 mm over length 72.3 mm (from Z=0.0 to Z=153.5).\n12. Finish turn diameter Ø46.9 mm over length 81.2 mm (from Z=0.0 to Z=81.2).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00415
|
images/Shaft_00415.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø40.0 mm and length at least 206.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø38.0 mm over length 54.8 mm (from Z=0.0 to Z=54.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø38.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø31.1 mm over length 36.3 mm (from Z=0.0 to Z=146.5).\n10. Finish turn diameter Ø30.0 mm over length 110.2 mm (from Z=0.0 to Z=110.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00595
|
images/Shaft_00595.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø49.5 mm and length at least 222.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø47.5 mm over length 56.4 mm (from Z=0.0 to Z=56.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø47.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø33.7 mm over length 22.1 mm (from Z=0.0 to Z=161.2).\n10. Finish turn diameter Ø30.0 mm over length 139.1 mm (from Z=0.0 to Z=139.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00258
|
images/Shaft_00258.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø64.0 mm and length at least 91.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø62.0 mm over length 17.7 mm (from Z=0.0 to Z=17.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø62.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø49.0 mm over length 10.2 mm (from Z=0.0 to Z=68.7).\n9. Finish turn diameter Ø42.9 mm over length 6.3 mm (from Z=0.0 to Z=58.5).\n10. Finish turn diameter Ø33.8 mm over length 14.7 mm (from Z=0.0 to Z=52.2).\n11. Finish turn diameter Ø30.0 mm over length 37.5 mm (from Z=0.0 to Z=37.5).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00313
|
images/Shaft_00313.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø59.8 mm and length at least 84.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.8 mm over length 35.8 mm (from Z=0.0 to Z=35.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø49.2 mm over length 8.4 mm (from Z=0.0 to Z=43.8).\n9. Finish turn diameter Ø34.8 mm over length 35.4 mm (from Z=0.0 to Z=35.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00409
|
images/Shaft_00409.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø43.7 mm and length at least 185.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.7 mm over length 25.2 mm (from Z=0.0 to Z=25.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø37.2 mm over length 27.1 mm (from Z=0.0 to Z=155.2).\n10. Finish turn diameter Ø30.0 mm over length 128.1 mm (from Z=0.0 to Z=128.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00162
|
images/Shaft_00162.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø55.4 mm and length at least 291.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.4 mm over length 28.0 mm (from Z=0.0 to Z=28.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø47.3 mm over length 70.0 mm (from Z=0.0 to Z=258.5).\n10. Finish turn diameter Ø35.0 mm over length 67.0 mm (from Z=0.0 to Z=188.5).\n11. Finish turn diameter Ø30.0 mm over length 121.5 mm (from Z=0.0 to Z=121.5).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00304
|
images/Shaft_00304.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø77.5 mm and length at least 232.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø75.5 mm over length 10.0 mm (from Z=0.0 to Z=10.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø75.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø60.0 mm over length 76.4 mm (from Z=0.0 to Z=217.0).\n10. Finish turn diameter Ø47.0 mm over length 10.0 mm (from Z=0.0 to Z=140.6).\n11. Finish turn diameter Ø41.4 mm over length 30.7 mm (from Z=0.0 to Z=130.6).\n12. Finish turn diameter Ø30.0 mm over length 99.9 mm (from Z=0.0 to Z=99.9).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00286
|
images/Shaft_00286.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø43.3 mm and length at least 280.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.3 mm over length 62.5 mm (from Z=0.0 to Z=62.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 213.1 mm (from Z=0.0 to Z=213.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00644
|
images/Shaft_00644.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø66.9 mm and length at least 291.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø64.9 mm over length 74.2 mm (from Z=0.0 to Z=74.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø64.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø53.1 mm over length 34.3 mm (from Z=0.0 to Z=212.0).\n10. Finish turn diameter Ø48.3 mm over length 61.4 mm (from Z=0.0 to Z=177.7).\n11. Finish turn diameter Ø30.0 mm over length 116.3 mm (from Z=0.0 to Z=116.3).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00635
|
images/Shaft_00635.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø64.8 mm and length at least 172.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø62.8 mm over length 44.6 mm (from Z=0.0 to Z=44.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø62.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø48.6 mm over length 43.0 mm (from Z=0.0 to Z=122.7).\n9. Finish turn diameter Ø42.4 mm over length 58.0 mm (from Z=0.0 to Z=79.7).\n10. Finish turn diameter Ø30.8 mm over length 21.7 mm (from Z=0.0 to Z=21.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00353
|
images/Shaft_00353.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø43.4 mm and length at least 164.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.4 mm over length 54.9 mm (from Z=0.0 to Z=54.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø32.1 mm over length 82.4 mm (from Z=0.0 to Z=104.9).\n9. Finish turn diameter Ø30.0 mm over length 22.5 mm (from Z=0.0 to Z=22.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00068
|
images/Shaft_00068.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 284.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 235.4 mm (from Z=0.0 to Z=235.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø27.1 mm over length 43.8 mm (from Z=0.0 to Z=43.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00678
|
images/Shaft_00678.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø60.3 mm and length at least 235.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø58.3 mm over length 23.1 mm (from Z=0.0 to Z=23.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø58.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø44.7 mm over length 56.0 mm (from Z=0.0 to Z=207.0).\n10. Finish turn diameter Ø34.9 mm over length 39.8 mm (from Z=0.0 to Z=151.0).\n11. Finish turn diameter Ø30.0 mm over length 111.2 mm (from Z=0.0 to Z=111.2).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00833
|
images/Shaft_00833.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 130.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 107.5 mm (from Z=0.0 to Z=107.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø29.2 mm over length 17.9 mm (from Z=0.0 to Z=17.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00935
|
images/Shaft_00935.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø45.1 mm and length at least 318.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø43.1 mm over length 107.0 mm (from Z=0.0 to Z=107.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø43.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø37.6 mm over length 15.1 mm (from Z=0.0 to Z=206.1).\n10. Finish turn diameter Ø30.0 mm over length 191.0 mm (from Z=0.0 to Z=191.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00679
|
images/Shaft_00679.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø48.0 mm and length at least 196.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø46.0 mm over length 58.6 mm (from Z=0.0 to Z=58.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø46.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 132.4 mm (from Z=0.0 to Z=132.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00719
|
images/Shaft_00719.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø77.6 mm and length at least 129.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø75.6 mm over length 49.0 mm (from Z=0.0 to Z=49.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø75.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø57.2 mm over length 38.3 mm (from Z=0.0 to Z=75.8).\n9. Finish turn diameter Ø44.0 mm over length 37.5 mm (from Z=0.0 to Z=37.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00237
|
images/Shaft_00237.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø77.2 mm and length at least 306.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø75.2 mm over length 37.3 mm (from Z=0.0 to Z=37.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø75.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø59.7 mm over length 18.8 mm (from Z=0.0 to Z=263.8).\n10. Finish turn diameter Ø46.9 mm over length 57.8 mm (from Z=0.0 to Z=245.0).\n11. Finish turn diameter Ø37.8 mm over length 60.2 mm (from Z=0.0 to Z=187.2).\n12. Finish turn diameter Ø30.0 mm over length 127.0 mm (from Z=0.0 to Z=127.0).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00265
|
images/Shaft_00265.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø39.7 mm and length at least 184.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø37.7 mm over length 39.5 mm (from Z=0.0 to Z=39.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø37.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 139.6 mm (from Z=0.0 to Z=139.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00090
|
images/Shaft_00090.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø53.4 mm and length at least 235.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø51.4 mm over length 44.2 mm (from Z=0.0 to Z=44.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø51.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø37.2 mm over length 34.0 mm (from Z=0.0 to Z=185.9).\n10. Finish turn diameter Ø30.0 mm over length 151.9 mm (from Z=0.0 to Z=151.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00835
|
images/Shaft_00835.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø59.9 mm and length at least 310.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.9 mm over length 74.4 mm (from Z=0.0 to Z=74.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø40.1 mm over length 76.1 mm (from Z=0.0 to Z=231.5).\n10. Finish turn diameter Ø34.9 mm over length 85.2 mm (from Z=0.0 to Z=155.4).\n11. Finish turn diameter Ø30.0 mm over length 70.2 mm (from Z=0.0 to Z=70.2).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00862
|
images/Shaft_00862.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø46.1 mm and length at least 85.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø44.1 mm over length 18.4 mm (from Z=0.0 to Z=18.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø44.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø32.0 mm over length 19.7 mm (from Z=0.0 to Z=61.6).\n9. Finish turn diameter Ø30.0 mm over length 41.9 mm (from Z=0.0 to Z=41.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00054
|
images/Shaft_00054.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø57.0 mm and length at least 134.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø55.0 mm over length 21.2 mm (from Z=0.0 to Z=21.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø55.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø43.3 mm over length 51.1 mm (from Z=0.0 to Z=108.2).\n9. Finish turn diameter Ø30.0 mm over length 57.1 mm (from Z=0.0 to Z=57.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00657
|
images/Shaft_00657.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 177.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 127.5 mm (from Z=0.0 to Z=127.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø26.7 mm over length 44.9 mm (from Z=0.0 to Z=44.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00943
|
images/Shaft_00943.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø42.3 mm and length at least 137.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø40.3 mm over length 7.5 mm (from Z=0.0 to Z=7.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø40.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.6 mm over length 25.9 mm (from Z=0.0 to Z=125.1).\n10. Finish turn diameter Ø30.0 mm over length 99.2 mm (from Z=0.0 to Z=99.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00406
|
images/Shaft_00406.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø69.2 mm and length at least 69.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.2 mm over length 9.0 mm (from Z=0.0 to Z=9.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø62.8 mm over length 15.2 mm (from Z=0.0 to Z=55.0).\n9. Finish turn diameter Ø51.6 mm over length 32.8 mm (from Z=0.0 to Z=39.8).\n10. Finish turn diameter Ø32.8 mm over length 7.0 mm (from Z=0.0 to Z=7.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00380
|
images/Shaft_00380.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø39.6 mm and length at least 78.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø37.6 mm over length 8.3 mm (from Z=0.0 to Z=8.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø37.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø33.9 mm over length 20.4 mm (from Z=0.0 to Z=65.4).\n9. Finish turn diameter Ø30.0 mm over length 45.0 mm (from Z=0.0 to Z=45.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00124
|
images/Shaft_00124.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 192.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 134.6 mm (from Z=0.0 to Z=134.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø18.6 mm over length 52.4 mm (from Z=0.0 to Z=52.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00491
|
images/Shaft_00491.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø55.6 mm and length at least 162.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.6 mm over length 51.0 mm (from Z=0.0 to Z=51.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø47.0 mm over length 25.5 mm (from Z=0.0 to Z=106.4).\n9. Finish turn diameter Ø36.8 mm over length 5.8 mm (from Z=0.0 to Z=80.9).\n10. Finish turn diameter Ø30.6 mm over length 51.9 mm (from Z=0.0 to Z=75.1).\n11. Finish turn diameter Ø30.0 mm over length 23.2 mm (from Z=0.0 to Z=23.2).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00802
|
images/Shaft_00802.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø55.1 mm and length at least 96.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.1 mm over length 22.9 mm (from Z=0.0 to Z=22.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø44.0 mm over length 42.7 mm (from Z=0.0 to Z=68.9).\n9. Finish turn diameter Ø37.5 mm over length 26.2 mm (from Z=0.0 to Z=26.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00900
|
images/Shaft_00900.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø40.4 mm and length at least 218.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø38.4 mm over length 11.0 mm (from Z=0.0 to Z=11.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø38.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø34.4 mm over length 97.6 mm (from Z=0.0 to Z=202.4).\n10. Finish turn diameter Ø30.0 mm over length 104.8 mm (from Z=0.0 to Z=104.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00430
|
images/Shaft_00430.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 137.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 123.1 mm (from Z=0.0 to Z=123.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø21.8 mm over length 9.4 mm (from Z=0.0 to Z=9.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00945
|
images/Shaft_00945.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø59.9 mm and length at least 320.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.9 mm over length 90.4 mm (from Z=0.0 to Z=90.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø47.8 mm over length 62.4 mm (from Z=0.0 to Z=225.0).\n10. Finish turn diameter Ø37.0 mm over length 92.7 mm (from Z=0.0 to Z=162.6).\n11. Finish turn diameter Ø30.0 mm over length 69.9 mm (from Z=0.0 to Z=69.9).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00703
|
images/Shaft_00703.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.3 mm and length at least 240.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.3 mm over length 70.2 mm (from Z=0.0 to Z=70.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 164.8 mm (from Z=0.0 to Z=164.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00294
|
images/Shaft_00294.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø76.7 mm and length at least 308.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø74.7 mm over length 87.7 mm (from Z=0.0 to Z=87.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø74.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø64.6 mm over length 39.7 mm (from Z=0.0 to Z=215.4).\n10. Finish turn diameter Ø46.3 mm over length 58.6 mm (from Z=0.0 to Z=175.7).\n11. Finish turn diameter Ø37.7 mm over length 38.0 mm (from Z=0.0 to Z=117.1).\n12. Finish turn diameter Ø30.0 mm over length 79.1 mm (from Z=0.0 to Z=79.1).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00878
|
images/Shaft_00878.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø39.0 mm and length at least 188.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø37.0 mm over length 23.0 mm (from Z=0.0 to Z=23.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø37.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 160.9 mm (from Z=0.0 to Z=160.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00212
|
images/Shaft_00212.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø77.8 mm and length at least 160.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø75.8 mm over length 21.1 mm (from Z=0.0 to Z=21.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø75.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø72.1 mm over length 61.5 mm (from Z=0.0 to Z=134.3).\n9. Finish turn diameter Ø68.7 mm over length 55.0 mm (from Z=0.0 to Z=72.8).\n10. Finish turn diameter Ø59.2 mm over length 17.8 mm (from Z=0.0 to Z=17.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00918
|
images/Shaft_00918.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø57.7 mm and length at least 109.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø55.7 mm over length 12.3 mm (from Z=0.0 to Z=12.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø55.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø39.9 mm over length 16.7 mm (from Z=0.0 to Z=92.4).\n9. Finish turn diameter Ø30.0 mm over length 75.7 mm (from Z=0.0 to Z=75.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00037
|
images/Shaft_00037.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø40.9 mm and length at least 205.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø38.9 mm over length 42.6 mm (from Z=0.0 to Z=42.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø38.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 157.4 mm (from Z=0.0 to Z=157.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00860
|
images/Shaft_00860.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø45.1 mm and length at least 284.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø43.1 mm over length 66.7 mm (from Z=0.0 to Z=66.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø43.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø39.7 mm over length 71.6 mm (from Z=0.0 to Z=212.8).\n10. Finish turn diameter Ø33.7 mm over length 78.3 mm (from Z=0.0 to Z=141.2).\n11. Finish turn diameter Ø30.0 mm over length 62.9 mm (from Z=0.0 to Z=62.9).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00898
|
images/Shaft_00898.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø55.2 mm and length at least 246.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.2 mm over length 25.1 mm (from Z=0.0 to Z=25.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø35.4 mm over length 42.0 mm (from Z=0.0 to Z=216.4).\n10. Finish turn diameter Ø30.0 mm over length 174.4 mm (from Z=0.0 to Z=174.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00125
|
images/Shaft_00125.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø33.9 mm and length at least 135.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø31.9 mm over length 24.5 mm (from Z=0.0 to Z=24.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø31.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 105.7 mm (from Z=0.0 to Z=105.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00023
|
images/Shaft_00023.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø54.1 mm and length at least 87.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø52.1 mm over length 5.0 mm (from Z=0.0 to Z=5.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø52.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø35.1 mm over length 5.0 mm (from Z=0.0 to Z=77.1).\n9. Finish turn diameter Ø30.0 mm over length 72.1 mm (from Z=0.0 to Z=72.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00839
|
images/Shaft_00839.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø34.9 mm and length at least 222.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.9 mm over length 72.7 mm (from Z=0.0 to Z=72.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 144.4 mm (from Z=0.0 to Z=144.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00976
|
images/Shaft_00976.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø61.3 mm and length at least 175.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø59.3 mm over length 72.4 mm (from Z=0.0 to Z=72.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø59.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø51.5 mm over length 32.4 mm (from Z=0.0 to Z=97.8).\n9. Finish turn diameter Ø46.3 mm over length 65.4 mm (from Z=0.0 to Z=65.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00101
|
images/Shaft_00101.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø53.6 mm and length at least 77.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø51.6 mm over length 16.6 mm (from Z=0.0 to Z=16.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø51.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø40.6 mm over length 10.8 mm (from Z=0.0 to Z=55.8).\n9. Finish turn diameter Ø30.0 mm over length 45.0 mm (from Z=0.0 to Z=45.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00115
|
images/Shaft_00115.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø54.8 mm and length at least 147.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø52.8 mm over length 27.3 mm (from Z=0.0 to Z=27.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø52.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø43.5 mm over length 25.0 mm (from Z=0.0 to Z=115.6).\n9. Finish turn diameter Ø33.3 mm over length 31.5 mm (from Z=0.0 to Z=90.6).\n10. Finish turn diameter Ø30.0 mm over length 59.1 mm (from Z=0.0 to Z=59.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00435
|
images/Shaft_00435.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø64.3 mm and length at least 176.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø62.3 mm over length 18.4 mm (from Z=0.0 to Z=18.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø62.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø56.4 mm over length 56.2 mm (from Z=0.0 to Z=152.8).\n9. Finish turn diameter Ø39.7 mm over length 13.4 mm (from Z=0.0 to Z=96.6).\n10. Finish turn diameter Ø35.5 mm over length 48.5 mm (from Z=0.0 to Z=83.2).\n11. Finish turn diameter Ø30.0 mm over length 34.7 mm (from Z=0.0 to Z=34.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00950
|
images/Shaft_00950.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø67.4 mm and length at least 212.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.4 mm over length 18.4 mm (from Z=0.0 to Z=18.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø61.3 mm over length 58.9 mm (from Z=0.0 to Z=189.1).\n10. Finish turn diameter Ø55.0 mm over length 50.2 mm (from Z=0.0 to Z=130.2).\n11. Finish turn diameter Ø39.8 mm over length 26.9 mm (from Z=0.0 to Z=80.0).\n12. Finish turn diameter Ø33.0 mm over length 53.1 mm (from Z=0.0 to Z=53.1).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00120
|
images/Shaft_00120.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø75.3 mm and length at least 257.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.3 mm over length 26.9 mm (from Z=0.0 to Z=26.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø53.8 mm over length 25.0 mm (from Z=0.0 to Z=226.0).\n10. Finish turn diameter Ø35.2 mm over length 42.7 mm (from Z=0.0 to Z=201.0).\n11. Finish turn diameter Ø30.0 mm over length 158.3 mm (from Z=0.0 to Z=158.3).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00384
|
images/Shaft_00384.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø56.3 mm and length at least 245.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.3 mm over length 28.0 mm (from Z=0.0 to Z=28.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø36.7 mm over length 85.2 mm (from Z=0.0 to Z=212.7).\n10. Finish turn diameter Ø30.0 mm over length 127.5 mm (from Z=0.0 to Z=127.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00047
|
images/Shaft_00047.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 318.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 266.5 mm (from Z=0.0 to Z=266.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø26.3 mm over length 47.1 mm (from Z=0.0 to Z=47.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00171
|
images/Shaft_00171.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø73.6 mm and length at least 306.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø71.6 mm over length 10.8 mm (from Z=0.0 to Z=10.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø71.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø64.0 mm over length 86.1 mm (from Z=0.0 to Z=290.3).\n10. Finish turn diameter Ø53.0 mm over length 111.8 mm (from Z=0.0 to Z=204.2).\n11. Finish turn diameter Ø36.5 mm over length 45.5 mm (from Z=0.0 to Z=92.4).\n12. Finish turn diameter Ø30.0 mm over length 46.9 mm (from Z=0.0 to Z=46.9).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00317
|
images/Shaft_00317.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø40.9 mm and length at least 225.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø38.9 mm over length 139.1 mm (from Z=0.0 to Z=139.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø38.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø33.9 mm over length 66.8 mm (from Z=0.0 to Z=81.3).\n10. Finish turn diameter Ø30.0 mm over length 14.5 mm (from Z=0.0 to Z=14.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00324
|
images/Shaft_00324.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø71.8 mm and length at least 158.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø69.8 mm over length 34.4 mm (from Z=0.0 to Z=34.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø69.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø50.3 mm over length 35.6 mm (from Z=0.0 to Z=119.2).\n9. Finish turn diameter Ø41.1 mm over length 48.4 mm (from Z=0.0 to Z=83.6).\n10. Finish turn diameter Ø30.0 mm over length 35.2 mm (from Z=0.0 to Z=35.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00880
|
images/Shaft_00880.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø75.6 mm and length at least 86.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.6 mm over length 7.9 mm (from Z=0.0 to Z=7.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø61.2 mm over length 19.6 mm (from Z=0.0 to Z=73.6).\n9. Finish turn diameter Ø44.5 mm over length 14.4 mm (from Z=0.0 to Z=54.0).\n10. Finish turn diameter Ø30.5 mm over length 19.4 mm (from Z=0.0 to Z=39.6).\n11. Finish turn diameter Ø30.0 mm over length 20.2 mm (from Z=0.0 to Z=20.2).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00263
|
images/Shaft_00263.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø47.3 mm and length at least 68.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø45.3 mm over length 5.0 mm (from Z=0.0 to Z=5.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø45.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø39.8 mm over length 19.0 mm (from Z=0.0 to Z=58.0).\n9. Finish turn diameter Ø30.0 mm over length 39.0 mm (from Z=0.0 to Z=39.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00145
|
images/Shaft_00145.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø60.3 mm and length at least 150.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø58.3 mm over length 57.7 mm (from Z=0.0 to Z=57.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø58.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø49.2 mm over length 10.9 mm (from Z=0.0 to Z=88.1).\n9. Finish turn diameter Ø30.3 mm over length 28.7 mm (from Z=0.0 to Z=77.2).\n10. Finish turn diameter Ø30.0 mm over length 48.5 mm (from Z=0.0 to Z=48.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00043
|
images/Shaft_00043.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø46.1 mm and length at least 322.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø44.1 mm over length 87.9 mm (from Z=0.0 to Z=87.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø44.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 229.2 mm (from Z=0.0 to Z=229.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00504
|
images/Shaft_00504.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø45.2 mm and length at least 283.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø43.2 mm over length 79.1 mm (from Z=0.0 to Z=79.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø43.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 199.4 mm (from Z=0.0 to Z=199.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00086
|
images/Shaft_00086.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø66.1 mm and length at least 202.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø64.1 mm over length 34.5 mm (from Z=0.0 to Z=34.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø64.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø45.7 mm over length 50.5 mm (from Z=0.0 to Z=163.4).\n10. Finish turn diameter Ø36.3 mm over length 23.5 mm (from Z=0.0 to Z=112.9).\n11. Finish turn diameter Ø30.0 mm over length 89.4 mm (from Z=0.0 to Z=89.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00376
|
images/Shaft_00376.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø36.9 mm and length at least 99.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø34.9 mm over length 21.4 mm (from Z=0.0 to Z=21.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø34.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 73.2 mm (from Z=0.0 to Z=73.2).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00530
|
images/Shaft_00530.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 304.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 279.2 mm (from Z=0.0 to Z=279.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø26.0 mm over length 20.6 mm (from Z=0.0 to Z=20.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00984
|
images/Shaft_00984.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø80.3 mm and length at least 318.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.3 mm over length 38.2 mm (from Z=0.0 to Z=38.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø74.4 mm over length 26.3 mm (from Z=0.0 to Z=275.7).\n10. Finish turn diameter Ø63.4 mm over length 76.7 mm (from Z=0.0 to Z=249.4).\n11. Finish turn diameter Ø50.6 mm over length 69.4 mm (from Z=0.0 to Z=172.7).\n12. Finish turn diameter Ø38.4 mm over length 31.7 mm (from Z=0.0 to Z=103.3).\n13. Finish turn diameter Ø30.0 mm over length 71.6 mm (from Z=0.0 to Z=71.6).\n14. Break all edges (e.g., 2×45° where applicable).\n15. Remove the workpiece from the lathe."
}
] |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.