id
stringlengths 11
11
| image
stringlengths 22
22
| conversations
listlengths 2
2
|
|---|---|---|
Shaft_00883
|
images/Shaft_00883.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø69.3 mm and length at least 90.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.3 mm over length 22.5 mm (from Z=0.0 to Z=22.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø63.2 mm over length 8.7 mm (from Z=0.0 to Z=63.4).\n9. Finish turn diameter Ø58.3 mm over length 28.8 mm (from Z=0.0 to Z=54.7).\n10. Finish turn diameter Ø40.1 mm over length 25.9 mm (from Z=0.0 to Z=25.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00173
|
images/Shaft_00173.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 96.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 75.1 mm (from Z=0.0 to Z=75.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø24.4 mm over length 16.3 mm (from Z=0.0 to Z=16.3).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00147
|
images/Shaft_00147.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø75.2 mm and length at least 156.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.2 mm over length 43.0 mm (from Z=0.0 to Z=43.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø61.6 mm over length 35.4 mm (from Z=0.0 to Z=108.4).\n9. Finish turn diameter Ø57.0 mm over length 73.0 mm (from Z=0.0 to Z=73.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00419
|
images/Shaft_00419.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø64.5 mm and length at least 230.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø62.5 mm over length 10.0 mm (from Z=0.0 to Z=10.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø62.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø51.2 mm over length 57.8 mm (from Z=0.0 to Z=215.0).\n10. Finish turn diameter Ø46.7 mm over length 30.8 mm (from Z=0.0 to Z=157.2).\n11. Finish turn diameter Ø30.4 mm over length 51.4 mm (from Z=0.0 to Z=126.4).\n12. Finish turn diameter Ø30.0 mm over length 75.0 mm (from Z=0.0 to Z=75.0).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00961
|
images/Shaft_00961.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø39.7 mm and length at least 189.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø37.7 mm over length 34.2 mm (from Z=0.0 to Z=34.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø37.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 150.1 mm (from Z=0.0 to Z=150.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00148
|
images/Shaft_00148.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø67.5 mm and length at least 189.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.5 mm over length 44.2 mm (from Z=0.0 to Z=44.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø57.4 mm over length 22.1 mm (from Z=0.0 to Z=140.6).\n9. Finish turn diameter Ø52.5 mm over length 68.3 mm (from Z=0.0 to Z=118.5).\n10. Finish turn diameter Ø40.8 mm over length 50.2 mm (from Z=0.0 to Z=50.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00975
|
images/Shaft_00975.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø76.4 mm and length at least 165.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø74.4 mm over length 45.2 mm (from Z=0.0 to Z=45.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø74.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø61.1 mm over length 42.9 mm (from Z=0.0 to Z=114.8).\n9. Finish turn diameter Ø54.7 mm over length 21.6 mm (from Z=0.0 to Z=71.9).\n10. Finish turn diameter Ø41.9 mm over length 25.6 mm (from Z=0.0 to Z=50.3).\n11. Finish turn diameter Ø36.2 mm over length 24.7 mm (from Z=0.0 to Z=24.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00079
|
images/Shaft_00079.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø34.0 mm and length at least 263.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.0 mm over length 36.0 mm (from Z=0.0 to Z=36.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 222.2 mm (from Z=0.0 to Z=222.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00775
|
images/Shaft_00775.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø80.4 mm and length at least 228.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.4 mm over length 61.4 mm (from Z=0.0 to Z=61.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø71.9 mm over length 6.0 mm (from Z=0.0 to Z=162.2).\n10. Finish turn diameter Ø62.5 mm over length 27.0 mm (from Z=0.0 to Z=156.2).\n11. Finish turn diameter Ø46.7 mm over length 44.5 mm (from Z=0.0 to Z=129.2).\n12. Finish turn diameter Ø40.8 mm over length 47.4 mm (from Z=0.0 to Z=84.7).\n13. Finish turn diameter Ø30.0 mm over length 37.3 mm (from Z=0.0 to Z=37.3).\n14. Break all edges (e.g., 2×45° where applicable).\n15. Remove the workpiece from the lathe."
}
] |
Shaft_00302
|
images/Shaft_00302.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø42.7 mm and length at least 102.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø40.7 mm over length 22.4 mm (from Z=0.0 to Z=22.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø40.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 75.3 mm (from Z=0.0 to Z=75.3).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00995
|
images/Shaft_00995.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø60.3 mm and length at least 292.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø58.3 mm over length 30.5 mm (from Z=0.0 to Z=30.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø58.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø40.3 mm over length 56.5 mm (from Z=0.0 to Z=256.6).\n10. Finish turn diameter Ø30.0 mm over length 200.1 mm (from Z=0.0 to Z=200.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00525
|
images/Shaft_00525.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø35.9 mm and length at least 90.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.9 mm over length 14.0 mm (from Z=0.0 to Z=14.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 71.9 mm (from Z=0.0 to Z=71.9).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00774
|
images/Shaft_00774.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø61.2 mm and length at least 272.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø59.2 mm over length 57.7 mm (from Z=0.0 to Z=57.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø59.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø42.2 mm over length 59.7 mm (from Z=0.0 to Z=209.9).\n10. Finish turn diameter Ø30.0 mm over length 150.2 mm (from Z=0.0 to Z=150.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00231
|
images/Shaft_00231.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø72.3 mm and length at least 136.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø70.3 mm over length 19.3 mm (from Z=0.0 to Z=19.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø70.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø60.8 mm over length 27.2 mm (from Z=0.0 to Z=112.1).\n9. Finish turn diameter Ø43.0 mm over length 6.4 mm (from Z=0.0 to Z=84.9).\n10. Finish turn diameter Ø30.0 mm over length 78.5 mm (from Z=0.0 to Z=78.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00625
|
images/Shaft_00625.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 252.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 206.7 mm (from Z=0.0 to Z=206.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø28.5 mm over length 40.3 mm (from Z=0.0 to Z=40.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00800
|
images/Shaft_00800.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 133.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 121.4 mm (from Z=0.0 to Z=121.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø22.0 mm over length 7.3 mm (from Z=0.0 to Z=7.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00561
|
images/Shaft_00561.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 247.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 193.2 mm (from Z=0.0 to Z=193.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø26.1 mm over length 49.5 mm (from Z=0.0 to Z=49.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00509
|
images/Shaft_00509.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 263.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 221.4 mm (from Z=0.0 to Z=221.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø26.3 mm over length 37.1 mm (from Z=0.0 to Z=37.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00840
|
images/Shaft_00840.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø68.5 mm and length at least 258.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø66.5 mm over length 29.6 mm (from Z=0.0 to Z=29.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø66.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø54.5 mm over length 29.0 mm (from Z=0.0 to Z=223.6).\n10. Finish turn diameter Ø45.9 mm over length 70.4 mm (from Z=0.0 to Z=194.6).\n11. Finish turn diameter Ø37.9 mm over length 32.3 mm (from Z=0.0 to Z=124.2).\n12. Finish turn diameter Ø30.0 mm over length 91.9 mm (from Z=0.0 to Z=91.9).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00494
|
images/Shaft_00494.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø79.2 mm and length at least 283.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.2 mm over length 64.6 mm (from Z=0.0 to Z=64.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø59.0 mm over length 44.5 mm (from Z=0.0 to Z=214.3).\n10. Finish turn diameter Ø52.2 mm over length 15.6 mm (from Z=0.0 to Z=169.8).\n11. Finish turn diameter Ø35.7 mm over length 49.8 mm (from Z=0.0 to Z=154.2).\n12. Finish turn diameter Ø30.0 mm over length 104.4 mm (from Z=0.0 to Z=104.4).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00119
|
images/Shaft_00119.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø58.0 mm and length at least 271.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø56.0 mm over length 35.0 mm (from Z=0.0 to Z=35.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø56.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø40.2 mm over length 21.7 mm (from Z=0.0 to Z=231.1).\n10. Finish turn diameter Ø30.0 mm over length 209.4 mm (from Z=0.0 to Z=209.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00477
|
images/Shaft_00477.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø56.9 mm and length at least 193.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.9 mm over length 29.8 mm (from Z=0.0 to Z=29.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø41.9 mm over length 49.0 mm (from Z=0.0 to Z=159.1).\n9. Finish turn diameter Ø37.9 mm over length 36.6 mm (from Z=0.0 to Z=110.1).\n10. Finish turn diameter Ø30.0 mm over length 73.5 mm (from Z=0.0 to Z=73.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00144
|
images/Shaft_00144.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø34.6 mm and length at least 123.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.6 mm over length 16.4 mm (from Z=0.0 to Z=16.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 101.9 mm (from Z=0.0 to Z=101.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00029
|
images/Shaft_00029.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø62.0 mm and length at least 256.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø60.0 mm over length 36.6 mm (from Z=0.0 to Z=36.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø60.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø55.1 mm over length 115.6 mm (from Z=0.0 to Z=214.8).\n10. Finish turn diameter Ø36.6 mm over length 99.2 mm (from Z=0.0 to Z=99.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00910
|
images/Shaft_00910.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø33.3 mm and length at least 247.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø31.3 mm over length 13.4 mm (from Z=0.0 to Z=13.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø31.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 229.2 mm (from Z=0.0 to Z=229.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00121
|
images/Shaft_00121.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø54.8 mm and length at least 235.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø52.8 mm over length 36.9 mm (from Z=0.0 to Z=36.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø52.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø49.2 mm over length 49.0 mm (from Z=0.0 to Z=193.6).\n10. Finish turn diameter Ø33.0 mm over length 38.9 mm (from Z=0.0 to Z=144.6).\n11. Finish turn diameter Ø30.0 mm over length 105.7 mm (from Z=0.0 to Z=105.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00605
|
images/Shaft_00605.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø46.4 mm and length at least 105.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø44.4 mm over length 20.0 mm (from Z=0.0 to Z=20.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø44.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø40.1 mm over length 7.2 mm (from Z=0.0 to Z=80.8).\n9. Finish turn diameter Ø30.0 mm over length 73.6 mm (from Z=0.0 to Z=73.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00061
|
images/Shaft_00061.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø33.4 mm and length at least 287.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø31.4 mm over length 73.7 mm (from Z=0.0 to Z=73.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø31.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 209.0 mm (from Z=0.0 to Z=209.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00871
|
images/Shaft_00871.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø79.3 mm and length at least 209.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.3 mm over length 107.4 mm (from Z=0.0 to Z=107.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø62.5 mm over length 67.2 mm (from Z=0.0 to Z=97.4).\n10. Finish turn diameter Ø43.2 mm over length 30.2 mm (from Z=0.0 to Z=30.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00572
|
images/Shaft_00572.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø52.7 mm and length at least 157.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø50.7 mm over length 16.0 mm (from Z=0.0 to Z=16.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø50.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø39.2 mm over length 88.9 mm (from Z=0.0 to Z=136.6).\n9. Finish turn diameter Ø30.0 mm over length 47.7 mm (from Z=0.0 to Z=47.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00005
|
images/Shaft_00005.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø33.8 mm and length at least 228.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø31.8 mm over length 22.4 mm (from Z=0.0 to Z=22.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø31.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 200.9 mm (from Z=0.0 to Z=200.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00926
|
images/Shaft_00926.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø62.5 mm and length at least 236.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø60.5 mm over length 72.3 mm (from Z=0.0 to Z=72.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø60.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø46.2 mm over length 101.0 mm (from Z=0.0 to Z=159.6).\n10. Finish turn diameter Ø39.2 mm over length 58.6 mm (from Z=0.0 to Z=58.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00639
|
images/Shaft_00639.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 156.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 121.5 mm (from Z=0.0 to Z=121.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø27.8 mm over length 29.5 mm (from Z=0.0 to Z=29.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00439
|
images/Shaft_00439.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø81.9 mm and length at least 319.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø79.9 mm over length 73.6 mm (from Z=0.0 to Z=73.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø79.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø68.7 mm over length 121.1 mm (from Z=0.0 to Z=241.2).\n10. Finish turn diameter Ø63.1 mm over length 63.0 mm (from Z=0.0 to Z=120.1).\n11. Finish turn diameter Ø51.9 mm over length 28.7 mm (from Z=0.0 to Z=57.1).\n12. Finish turn diameter Ø46.7 mm over length 28.4 mm (from Z=0.0 to Z=28.4).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00729
|
images/Shaft_00729.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø38.1 mm and length at least 79.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.1 mm over length 18.5 mm (from Z=0.0 to Z=18.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 55.6 mm (from Z=0.0 to Z=55.6).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00193
|
images/Shaft_00193.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø33.6 mm and length at least 98.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø31.6 mm over length 10.2 mm (from Z=0.0 to Z=10.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø31.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 82.9 mm (from Z=0.0 to Z=82.9).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00752
|
images/Shaft_00752.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø71.7 mm and length at least 112.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø69.7 mm over length 45.2 mm (from Z=0.0 to Z=45.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø69.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø65.2 mm over length 40.6 mm (from Z=0.0 to Z=61.9).\n9. Finish turn diameter Ø54.2 mm over length 21.3 mm (from Z=0.0 to Z=21.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00626
|
images/Shaft_00626.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø37.7 mm and length at least 257.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø35.7 mm over length 58.2 mm (from Z=0.0 to Z=58.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø35.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 194.1 mm (from Z=0.0 to Z=194.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00571
|
images/Shaft_00571.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø72.3 mm and length at least 216.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø70.3 mm over length 18.9 mm (from Z=0.0 to Z=18.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø70.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø57.8 mm over length 47.5 mm (from Z=0.0 to Z=192.7).\n10. Finish turn diameter Ø50.6 mm over length 56.8 mm (from Z=0.0 to Z=145.2).\n11. Finish turn diameter Ø34.7 mm over length 14.0 mm (from Z=0.0 to Z=88.4).\n12. Finish turn diameter Ø30.0 mm over length 74.4 mm (from Z=0.0 to Z=74.4).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00017
|
images/Shaft_00017.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø33.5 mm and length at least 162.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø31.5 mm over length 31.3 mm (from Z=0.0 to Z=31.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø31.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 126.5 mm (from Z=0.0 to Z=126.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00742
|
images/Shaft_00742.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø67.1 mm and length at least 67.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.1 mm over length 7.3 mm (from Z=0.0 to Z=7.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø56.1 mm over length 5.0 mm (from Z=0.0 to Z=55.0).\n9. Finish turn diameter Ø43.6 mm over length 11.9 mm (from Z=0.0 to Z=50.0).\n10. Finish turn diameter Ø30.0 mm over length 38.1 mm (from Z=0.0 to Z=38.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00914
|
images/Shaft_00914.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 69.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 58.8 mm (from Z=0.0 to Z=58.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø21.9 mm over length 6.0 mm (from Z=0.0 to Z=6.0).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00510
|
images/Shaft_00510.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø80.0 mm and length at least 227.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.0 mm over length 55.5 mm (from Z=0.0 to Z=55.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø65.1 mm over length 29.0 mm (from Z=0.0 to Z=166.5).\n10. Finish turn diameter Ø56.2 mm over length 34.8 mm (from Z=0.0 to Z=137.5).\n11. Finish turn diameter Ø42.9 mm over length 40.2 mm (from Z=0.0 to Z=102.7).\n12. Finish turn diameter Ø31.0 mm over length 62.5 mm (from Z=0.0 to Z=62.5).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00573
|
images/Shaft_00573.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø48.1 mm and length at least 226.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø46.1 mm over length 14.9 mm (from Z=0.0 to Z=14.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø46.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø31.2 mm over length 77.2 mm (from Z=0.0 to Z=206.5).\n10. Finish turn diameter Ø30.0 mm over length 129.3 mm (from Z=0.0 to Z=129.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00138
|
images/Shaft_00138.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø53.5 mm and length at least 214.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø51.5 mm over length 38.7 mm (from Z=0.0 to Z=38.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø51.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø41.2 mm over length 43.0 mm (from Z=0.0 to Z=170.6).\n10. Finish turn diameter Ø30.0 mm over length 127.6 mm (from Z=0.0 to Z=127.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00191
|
images/Shaft_00191.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø46.4 mm and length at least 211.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø44.4 mm over length 50.2 mm (from Z=0.0 to Z=50.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø44.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø31.4 mm over length 53.6 mm (from Z=0.0 to Z=156.7).\n10. Finish turn diameter Ø30.0 mm over length 103.1 mm (from Z=0.0 to Z=103.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00004
|
images/Shaft_00004.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 93.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 71.8 mm (from Z=0.0 to Z=71.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø28.4 mm over length 16.8 mm (from Z=0.0 to Z=16.8).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00443
|
images/Shaft_00443.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø76.0 mm and length at least 270.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø74.0 mm over length 58.1 mm (from Z=0.0 to Z=58.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø74.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø59.5 mm over length 28.9 mm (from Z=0.0 to Z=207.2).\n10. Finish turn diameter Ø56.3 mm over length 48.6 mm (from Z=0.0 to Z=178.3).\n11. Finish turn diameter Ø38.3 mm over length 40.6 mm (from Z=0.0 to Z=129.7).\n12. Finish turn diameter Ø30.0 mm over length 89.1 mm (from Z=0.0 to Z=89.1).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00020
|
images/Shaft_00020.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø76.6 mm and length at least 296.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø74.6 mm over length 76.9 mm (from Z=0.0 to Z=76.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø74.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø57.8 mm over length 96.6 mm (from Z=0.0 to Z=214.8).\n10. Finish turn diameter Ø48.9 mm over length 39.2 mm (from Z=0.0 to Z=118.2).\n11. Finish turn diameter Ø39.4 mm over length 79.0 mm (from Z=0.0 to Z=79.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00213
|
images/Shaft_00213.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø58.0 mm and length at least 308.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø56.0 mm over length 11.6 mm (from Z=0.0 to Z=11.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø56.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø43.8 mm over length 69.1 mm (from Z=0.0 to Z=292.3).\n10. Finish turn diameter Ø38.3 mm over length 64.1 mm (from Z=0.0 to Z=223.2).\n11. Finish turn diameter Ø30.2 mm over length 93.3 mm (from Z=0.0 to Z=159.1).\n12. Finish turn diameter Ø30.0 mm over length 65.8 mm (from Z=0.0 to Z=65.8).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00064
|
images/Shaft_00064.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø60.2 mm and length at least 210.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø58.2 mm over length 35.1 mm (from Z=0.0 to Z=35.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø58.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø40.7 mm over length 27.9 mm (from Z=0.0 to Z=169.9).\n10. Finish turn diameter Ø31.4 mm over length 76.9 mm (from Z=0.0 to Z=142.0).\n11. Finish turn diameter Ø30.0 mm over length 65.1 mm (from Z=0.0 to Z=65.1).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00411
|
images/Shaft_00411.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø74.0 mm and length at least 106.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.0 mm over length 26.1 mm (from Z=0.0 to Z=26.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø64.7 mm over length 23.6 mm (from Z=0.0 to Z=75.4).\n9. Finish turn diameter Ø55.9 mm over length 5.0 mm (from Z=0.0 to Z=51.8).\n10. Finish turn diameter Ø39.3 mm over length 22.8 mm (from Z=0.0 to Z=46.8).\n11. Finish turn diameter Ø30.0 mm over length 24.0 mm (from Z=0.0 to Z=24.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00301
|
images/Shaft_00301.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø47.0 mm and length at least 169.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø45.0 mm over length 46.9 mm (from Z=0.0 to Z=46.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø45.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø40.1 mm over length 22.8 mm (from Z=0.0 to Z=117.4).\n10. Finish turn diameter Ø30.0 mm over length 94.6 mm (from Z=0.0 to Z=94.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00333
|
images/Shaft_00333.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø79.1 mm and length at least 202.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.1 mm over length 48.5 mm (from Z=0.0 to Z=48.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø64.8 mm over length 71.6 mm (from Z=0.0 to Z=149.4).\n10. Finish turn diameter Ø47.4 mm over length 14.4 mm (from Z=0.0 to Z=77.8).\n11. Finish turn diameter Ø30.0 mm over length 63.4 mm (from Z=0.0 to Z=63.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00192
|
images/Shaft_00192.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø38.6 mm and length at least 261.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.6 mm over length 35.6 mm (from Z=0.0 to Z=35.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 220.5 mm (from Z=0.0 to Z=220.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00664
|
images/Shaft_00664.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø49.3 mm and length at least 184.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø47.3 mm over length 64.0 mm (from Z=0.0 to Z=64.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø47.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø40.3 mm over length 66.6 mm (from Z=0.0 to Z=115.4).\n9. Finish turn diameter Ø33.2 mm over length 48.8 mm (from Z=0.0 to Z=48.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00262
|
images/Shaft_00262.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø40.6 mm and length at least 111.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø38.6 mm over length 46.7 mm (from Z=0.0 to Z=46.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø38.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 59.9 mm (from Z=0.0 to Z=59.9).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00647
|
images/Shaft_00647.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 287.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 171.9 mm (from Z=0.0 to Z=171.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø27.8 mm over length 110.3 mm (from Z=0.0 to Z=110.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00810
|
images/Shaft_00810.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø37.0 mm and length at least 273.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø35.0 mm over length 53.8 mm (from Z=0.0 to Z=53.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø35.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø31.5 mm over length 25.8 mm (from Z=0.0 to Z=214.7).\n10. Finish turn diameter Ø30.0 mm over length 188.9 mm (from Z=0.0 to Z=188.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00232
|
images/Shaft_00232.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø50.3 mm and length at least 221.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø48.3 mm over length 45.7 mm (from Z=0.0 to Z=45.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø48.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 170.6 mm (from Z=0.0 to Z=170.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00795
|
images/Shaft_00795.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø47.7 mm and length at least 293.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø45.7 mm over length 55.2 mm (from Z=0.0 to Z=55.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø45.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.9 mm over length 38.1 mm (from Z=0.0 to Z=233.2).\n10. Finish turn diameter Ø33.0 mm over length 22.4 mm (from Z=0.0 to Z=195.1).\n11. Finish turn diameter Ø30.0 mm over length 172.7 mm (from Z=0.0 to Z=172.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00681
|
images/Shaft_00681.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø66.7 mm and length at least 314.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø64.7 mm over length 69.9 mm (from Z=0.0 to Z=69.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø64.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø58.5 mm over length 63.6 mm (from Z=0.0 to Z=239.7).\n10. Finish turn diameter Ø50.9 mm over length 14.2 mm (from Z=0.0 to Z=176.1).\n11. Finish turn diameter Ø38.8 mm over length 67.5 mm (from Z=0.0 to Z=161.9).\n12. Finish turn diameter Ø33.9 mm over length 28.1 mm (from Z=0.0 to Z=94.4).\n13. Finish turn diameter Ø30.0 mm over length 66.3 mm (from Z=0.0 to Z=66.3).\n14. Break all edges (e.g., 2×45° where applicable).\n15. Remove the workpiece from the lathe."
}
] |
Shaft_00804
|
images/Shaft_00804.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø38.6 mm and length at least 216.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.6 mm over length 68.3 mm (from Z=0.0 to Z=68.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 143.3 mm (from Z=0.0 to Z=143.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00482
|
images/Shaft_00482.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø58.3 mm and length at least 231.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø56.3 mm over length 28.0 mm (from Z=0.0 to Z=28.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø56.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø42.4 mm over length 62.8 mm (from Z=0.0 to Z=198.2).\n10. Finish turn diameter Ø35.4 mm over length 105.9 mm (from Z=0.0 to Z=135.4).\n11. Finish turn diameter Ø30.0 mm over length 29.5 mm (from Z=0.0 to Z=29.5).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00360
|
images/Shaft_00360.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø35.0 mm and length at least 251.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.0 mm over length 27.9 mm (from Z=0.0 to Z=27.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 218.4 mm (from Z=0.0 to Z=218.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00838
|
images/Shaft_00838.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 108.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 82.2 mm (from Z=0.0 to Z=82.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø29.8 mm over length 21.5 mm (from Z=0.0 to Z=21.5).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00236
|
images/Shaft_00236.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø69.4 mm and length at least 228.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.4 mm over length 36.7 mm (from Z=0.0 to Z=36.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø56.6 mm over length 37.9 mm (from Z=0.0 to Z=187.1).\n10. Finish turn diameter Ø36.8 mm over length 58.8 mm (from Z=0.0 to Z=149.2).\n11. Finish turn diameter Ø30.0 mm over length 90.4 mm (from Z=0.0 to Z=90.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00627
|
images/Shaft_00627.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø61.1 mm and length at least 113.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø59.1 mm over length 55.5 mm (from Z=0.0 to Z=55.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø59.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø56.0 mm over length 19.8 mm (from Z=0.0 to Z=53.4).\n9. Finish turn diameter Ø40.7 mm over length 33.6 mm (from Z=0.0 to Z=33.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00957
|
images/Shaft_00957.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 293.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 228.0 mm (from Z=0.0 to Z=228.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø25.8 mm over length 60.9 mm (from Z=0.0 to Z=60.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00582
|
images/Shaft_00582.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø44.4 mm and length at least 247.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø42.4 mm over length 33.1 mm (from Z=0.0 to Z=33.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø42.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø36.0 mm over length 45.5 mm (from Z=0.0 to Z=209.7).\n10. Finish turn diameter Ø30.0 mm over length 164.2 mm (from Z=0.0 to Z=164.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00272
|
images/Shaft_00272.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø52.8 mm and length at least 78.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø50.8 mm over length 12.8 mm (from Z=0.0 to Z=12.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø50.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø33.2 mm over length 18.1 mm (from Z=0.0 to Z=60.2).\n9. Finish turn diameter Ø30.0 mm over length 42.1 mm (from Z=0.0 to Z=42.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00201
|
images/Shaft_00201.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø68.7 mm and length at least 130.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø66.7 mm over length 17.6 mm (from Z=0.0 to Z=17.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø66.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø50.8 mm over length 25.5 mm (from Z=0.0 to Z=107.8).\n9. Finish turn diameter Ø32.3 mm over length 30.1 mm (from Z=0.0 to Z=82.3).\n10. Finish turn diameter Ø30.0 mm over length 52.2 mm (from Z=0.0 to Z=52.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00013
|
images/Shaft_00013.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø51.2 mm and length at least 312.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø49.2 mm over length 108.4 mm (from Z=0.0 to Z=108.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø49.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø41.6 mm over length 75.6 mm (from Z=0.0 to Z=198.9).\n10. Finish turn diameter Ø32.2 mm over length 91.7 mm (from Z=0.0 to Z=123.3).\n11. Finish turn diameter Ø30.0 mm over length 31.6 mm (from Z=0.0 to Z=31.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00427
|
images/Shaft_00427.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.4 mm and length at least 125.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.4 mm over length 36.7 mm (from Z=0.0 to Z=36.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 84.1 mm (from Z=0.0 to Z=84.1).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00239
|
images/Shaft_00239.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø37.4 mm and length at least 115.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø35.4 mm over length 69.4 mm (from Z=0.0 to Z=69.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø35.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 41.1 mm (from Z=0.0 to Z=41.1).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00084
|
images/Shaft_00084.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 78.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 62.5 mm (from Z=0.0 to Z=62.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø22.3 mm over length 10.8 mm (from Z=0.0 to Z=10.8).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00532
|
images/Shaft_00532.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø52.5 mm and length at least 79.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø50.5 mm over length 17.3 mm (from Z=0.0 to Z=17.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø50.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø37.0 mm over length 19.5 mm (from Z=0.0 to Z=56.9).\n9. Finish turn diameter Ø30.0 mm over length 37.4 mm (from Z=0.0 to Z=37.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00172
|
images/Shaft_00172.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø44.9 mm and length at least 188.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø42.9 mm over length 33.9 mm (from Z=0.0 to Z=33.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø42.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 149.9 mm (from Z=0.0 to Z=149.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00289
|
images/Shaft_00289.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø80.4 mm and length at least 153.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.4 mm over length 28.7 mm (from Z=0.0 to Z=28.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø60.3 mm over length 14.2 mm (from Z=0.0 to Z=119.6).\n9. Finish turn diameter Ø51.5 mm over length 6.5 mm (from Z=0.0 to Z=105.4).\n10. Finish turn diameter Ø32.0 mm over length 24.8 mm (from Z=0.0 to Z=98.9).\n11. Finish turn diameter Ø30.0 mm over length 74.1 mm (from Z=0.0 to Z=74.1).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00485
|
images/Shaft_00485.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø79.5 mm and length at least 219.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.5 mm over length 32.5 mm (from Z=0.0 to Z=32.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø69.1 mm over length 57.4 mm (from Z=0.0 to Z=182.3).\n10. Finish turn diameter Ø59.9 mm over length 21.8 mm (from Z=0.0 to Z=124.9).\n11. Finish turn diameter Ø53.6 mm over length 59.6 mm (from Z=0.0 to Z=103.1).\n12. Finish turn diameter Ø48.9 mm over length 6.8 mm (from Z=0.0 to Z=43.5).\n13. Finish turn diameter Ø36.6 mm over length 36.7 mm (from Z=0.0 to Z=36.7).\n14. Break all edges (e.g., 2×45° where applicable).\n15. Remove the workpiece from the lathe."
}
] |
Shaft_00329
|
images/Shaft_00329.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 308.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 158.0 mm (from Z=0.0 to Z=158.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø23.7 mm over length 145.0 mm (from Z=0.0 to Z=145.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00683
|
images/Shaft_00683.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.7 mm and length at least 141.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.7 mm over length 40.6 mm (from Z=0.0 to Z=40.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 96.0 mm (from Z=0.0 to Z=96.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00318
|
images/Shaft_00318.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø78.3 mm and length at least 226.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø76.3 mm over length 71.3 mm (from Z=0.0 to Z=71.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø76.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø62.1 mm over length 25.1 mm (from Z=0.0 to Z=150.5).\n10. Finish turn diameter Ø54.4 mm over length 69.0 mm (from Z=0.0 to Z=125.4).\n11. Finish turn diameter Ø51.2 mm over length 14.4 mm (from Z=0.0 to Z=56.4).\n12. Finish turn diameter Ø38.3 mm over length 42.0 mm (from Z=0.0 to Z=42.0).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00454
|
images/Shaft_00454.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø49.1 mm and length at least 277.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø47.1 mm over length 64.8 mm (from Z=0.0 to Z=64.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø47.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 207.9 mm (from Z=0.0 to Z=207.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00249
|
images/Shaft_00249.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø65.1 mm and length at least 269.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.1 mm over length 61.5 mm (from Z=0.0 to Z=61.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø53.1 mm over length 36.3 mm (from Z=0.0 to Z=203.2).\n10. Finish turn diameter Ø37.0 mm over length 31.5 mm (from Z=0.0 to Z=166.9).\n11. Finish turn diameter Ø30.0 mm over length 135.4 mm (from Z=0.0 to Z=135.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00846
|
images/Shaft_00846.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø50.0 mm and length at least 99.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø48.0 mm over length 8.0 mm (from Z=0.0 to Z=8.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø48.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 86.4 mm (from Z=0.0 to Z=86.4).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00279
|
images/Shaft_00279.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø57.2 mm and length at least 303.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø55.2 mm over length 110.6 mm (from Z=0.0 to Z=110.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø55.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø40.7 mm over length 31.1 mm (from Z=0.0 to Z=187.5).\n10. Finish turn diameter Ø35.2 mm over length 119.9 mm (from Z=0.0 to Z=156.4).\n11. Finish turn diameter Ø31.0 mm over length 36.5 mm (from Z=0.0 to Z=36.5).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00455
|
images/Shaft_00455.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø66.0 mm and length at least 164.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø64.0 mm over length 34.8 mm (from Z=0.0 to Z=34.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø64.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø51.9 mm over length 50.0 mm (from Z=0.0 to Z=124.6).\n9. Finish turn diameter Ø43.1 mm over length 20.5 mm (from Z=0.0 to Z=74.6).\n10. Finish turn diameter Ø34.4 mm over length 54.1 mm (from Z=0.0 to Z=54.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00901
|
images/Shaft_00901.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø78.4 mm and length at least 212.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø76.4 mm over length 56.5 mm (from Z=0.0 to Z=56.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø76.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø59.0 mm over length 126.4 mm (from Z=0.0 to Z=150.6).\n10. Finish turn diameter Ø52.9 mm over length 24.2 mm (from Z=0.0 to Z=24.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00761
|
images/Shaft_00761.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø41.2 mm and length at least 124.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø39.2 mm over length 5.0 mm (from Z=0.0 to Z=5.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø39.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 114.3 mm (from Z=0.0 to Z=114.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00547
|
images/Shaft_00547.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø43.8 mm and length at least 215.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.8 mm over length 62.1 mm (from Z=0.0 to Z=62.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 148.6 mm (from Z=0.0 to Z=148.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00180
|
images/Shaft_00180.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø78.0 mm and length at least 146.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø76.0 mm over length 30.8 mm (from Z=0.0 to Z=30.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø76.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø65.3 mm over length 26.9 mm (from Z=0.0 to Z=110.3).\n9. Finish turn diameter Ø62.2 mm over length 33.5 mm (from Z=0.0 to Z=83.4).\n10. Finish turn diameter Ø58.1 mm over length 20.5 mm (from Z=0.0 to Z=49.9).\n11. Finish turn diameter Ø41.6 mm over length 19.4 mm (from Z=0.0 to Z=29.4).\n12. Finish turn diameter Ø30.0 mm over length 10.0 mm (from Z=0.0 to Z=10.0).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00557
|
images/Shaft_00557.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø40.7 mm and length at least 275.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø38.7 mm over length 97.8 mm (from Z=0.0 to Z=97.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø38.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 172.9 mm (from Z=0.0 to Z=172.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00628
|
images/Shaft_00628.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø71.0 mm and length at least 168.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø69.0 mm over length 39.5 mm (from Z=0.0 to Z=39.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø69.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø55.4 mm over length 25.7 mm (from Z=0.0 to Z=124.1).\n9. Finish turn diameter Ø47.8 mm over length 19.8 mm (from Z=0.0 to Z=98.4).\n10. Finish turn diameter Ø44.2 mm over length 34.7 mm (from Z=0.0 to Z=78.6).\n11. Finish turn diameter Ø33.8 mm over length 17.7 mm (from Z=0.0 to Z=43.9).\n12. Finish turn diameter Ø30.0 mm over length 26.2 mm (from Z=0.0 to Z=26.2).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00423
|
images/Shaft_00423.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø34.8 mm and length at least 249.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.8 mm over length 53.1 mm (from Z=0.0 to Z=53.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 191.0 mm (from Z=0.0 to Z=191.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00843
|
images/Shaft_00843.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø39.4 mm and length at least 219.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø37.4 mm over length 67.8 mm (from Z=0.0 to Z=67.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø37.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 147.1 mm (from Z=0.0 to Z=147.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00010
|
images/Shaft_00010.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø36.8 mm and length at least 98.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø34.8 mm over length 31.0 mm (from Z=0.0 to Z=31.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø34.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 62.8 mm (from Z=0.0 to Z=62.8).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00199
|
images/Shaft_00199.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø38.8 mm and length at least 141.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.8 mm over length 30.4 mm (from Z=0.0 to Z=30.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 105.9 mm (from Z=0.0 to Z=105.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00425
|
images/Shaft_00425.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø48.8 mm and length at least 205.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø46.8 mm over length 53.7 mm (from Z=0.0 to Z=53.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø46.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.8 mm over length 49.4 mm (from Z=0.0 to Z=146.4).\n10. Finish turn diameter Ø30.0 mm over length 97.0 mm (from Z=0.0 to Z=97.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00534
|
images/Shaft_00534.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø42.5 mm and length at least 117.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø40.5 mm over length 13.4 mm (from Z=0.0 to Z=13.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø40.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 99.4 mm (from Z=0.0 to Z=99.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.