Datasets:

TigerResearch

/

tigerbot-youtube-howto-en-50k

like 1

Follow

Tiger Research 69

Please explain how to make pan roasted halibut at home

I'm bill King executive chef from McCormick and Schmidt's seafood restaurants and it's held at season one of my favorite times a year actually Halbert seasons pretty long it runs from roughly March til the end of October most years and when the catch is good there's just plenty of halibut for everyone it's absolutely one of everyone's most favorite fish and it's very very popular in all of our restaurants so I'm going to prepare for you today a quintessentially Pacific Northwest item which is where the hell that comes from the only place in the world where great halibut is is taken out of the water so I've got this beautiful piece of halibut you can see it's nice thick fleshed bright color soft pink tone to the to the flesh absolutely gorgeous we're just going to put a little salt and pepper on it I don't like to season this fish too much with anything else because we've got a lot of flavor coming out in the sauce so a little kosher salt a little cracked black pepper I've got a nice hot pan ready to sear the fish just a little bit of oil and I love using the nonstick pan I Eve I put a little oil in it mostly to get carmelization on the fish it's not going to stick but between the nonstick and a little oil it's easy money in the pan halibut top side down because when you flip it then that's going to be a presentation side on your plate this is going to probably take six or eight minutes on each side maybe a little bit less depending on how hot you keep your pan and one thing you can do is that you can put your oven on about 400 degrees and get it just nice and brown and then you can pop it in the oven for five or six minutes and be about doing some other things your choice it goes either way today I'm going to do it all in the pan all right we've been about six minutes in the pan now and I think it's time to flip it we should see a beautiful golden brown which we do there it is you know how there's just this absolutely spectacular fish they're enormous they're the largest member of the flatfish family which includes all manner of soul and flounder but these fish a bit it's pretty typical for a fish to be 40 to 60 pounds in its market form for restaurants and markets these days but these fish can be over a hundred pounds and I've had I've had a whole halibut on on my table in the prep kitchen that was close to 150 pounds these are just remarkable fish they come from really deep cold water in the Pacific Northwest most of the best howl that comes from up around Alaska and it's just the most versatile sweet meat it's good for first-time seafood eaters it's relatively mild but it's got a pretty nice firm texture a beautiful flake to it it's just fabulous fish so we're going to be about another four or five minutes on this side and then it's going to be ready for the fish but we're going to do a real quick sauce well I think this fish is done it's looking beautiful golden I think it's the same on the other side let's take a quick peek absolutely perfect fit about 10 11 minutes in the pan and again like I said you could do this in the other we're going to take this fish out and we're going to put it right here I'm going to serve it in this in this pretty little boat shaped dish and we're going to make a very very quick pan sauce I'm going to turn the heat down just a touch and I'm going to take cassis which is black currant liqueur but if you don't want to put an alcohol-based liquid in here you could use a puree or a you know a juice even blackberry juice cranberry juice you can use anything like that this is particularly good and matches up with these beautiful big thick juicy blackberries that we're going to put in a sauce too so we're going to put this in the pan and we're just going to let it simmer away for about probably less than a minute it's going to get a little bit thicker then I'm going to put a splash of lemon juice a splash of rice wine vinegar and they'll give you a little tartness a little sharpness against sweet liqueur and then I'm going to add these blackberries these are actually marionberries from the heart of the Willamette Valley in Oregon and they are absolutely the most beautiful blackberries you can find anywhere so let's put them all in there we may not use them all but let's just that's good we're just going to let those berries heat and let that sauce simmer a little bit and in about a minute and a half we're going to have a perfect sauce for the fish so this sauce is ready now and it can be poured over the fish just the way it is but if you want to gild the lily a little bit at an extra bit of richness and silkiness to this sauce I'm going to put a pad of butter in here we're just going to work it around here just real quick I like that butter very very cold because as its added to the sauce and it melts it brings a little viscosity into the sauce and that's it as soon as that butter is done melting we're going to put it right over the fish blackberries we'll see if we can't keep some there we go and as if this wasn't quintessentially Pacific Northwest enough I'm going to scatter a few chopped toasted hazelnuts on here these are absolutely delicious with the blackberry and there you have it blackberry and hazelnut halibut from the Pacific Northwest I'm bill King executive chef from McCormick and Schmidt's seafood restaurants see you next time

Please explain how to make bracelets (cobra)

welcome to natural craft a YouTube channel where I'll be teaching you techniques to make your very own homemade jewelry not only are these techniques simple and fun they're also beautiful and fun to wear today's lesson Cobra to begin this project you'll need two colors of each piece will have to be about as long as from your hand to the middle of your chest you'll need a piece this length in both colors once you have your pieces measured equally you'll need to cut them once you've cut your measure how much fits around your wrist be sure to hold on to the spot that measures the length and then create a loop not in the top where the piece is fold like so now you're ready to begin your bracelet first you'll want to have the two shorter strings on the inside with the two longer strings on the outside we'll begin with pink make a loop with the pink string behind the two Center strings next you'll take the blue string behind the pink string on the right side keeping the blue string behind the pink string you'll take it across the front of the to Center strings and put it through the loop that you made with the pink it will look something like this you'll want to hold the center strings and the top loop and pull the string study to continue with traditional cobra you'll want to keep on making your first loop with the pink string continuing to loop behind the center strings followed by the blue behind the pink looping the blue across the center into the loop of the pink holding the bottom and the top loop and pulling the strings tight you'll continue to make your first loop with the pink every time for the remainder of the bracelet pink behind the center blue behind pink blue across the center into the pink lip you'll continue in this fashion for the remainder of your bracelet until you have something that looks like this once your bracelet is completed it will be reversible to secure your bracelet he'll take the remainder of the short strings and place them through the loop of the top of the bracelet you can use the remainder of the long strings to tie together with the short strings to secure your bracelet it will look slightly messy until you take a pair of scissors and cut off the excess string and there's your traditional Cobra bracelet another variation on Cobra is Cobra twist it begins the exact same way as traditional Cobra bringing the first string behind the center strings the second string behind the first across the front and through the first loop the difference in Cobra twist comes in in the second stitch when you don't continue with the first string instead you continue to make loops on the left side regardless of the color looping on the left side consistently creates a spiral effect and the result is Cobra twist similar to Chinese staircase Cobra twists has a spiral pattern you'll secure this bracelet in the same way that you secured your first bracelet bringing the remainder of the short pieces through the loop at the top taking the long pieces and tying them together with the shorter ones you and that's how you make Cobra twist thanks for joining me tune in next week when I'll teach you how to make all of the classics using hemp

Please explain how to grow starfruit trees from seed (grocery store growing ep. 8)

how did everyone and welcome back to another episode of grocery store growing right here on the more you grow it's finally a nice day outside it's not just freezing cold for a change it's even nice enough back and wear a short sleeve shirt today so I thought I'd rock my Texas boy shirt today if you haven't seen the Texas boys before go check out their channel they've always got awesome projects going on and a lot of cool things coming up but we've got some cool things coming up today in this episode as well I've got a fruit that the first word I think of that comes to mind to describe it is it's a star and that's a little bit pun intended because today we've got star fruit star fruit is a delicious fruit I'm going to talk a little bit about it I'm going to taste test it for y'all to let y'all know what it tastes like and how to eat it and then I'm gonna show you how you can start your very own star fruit trees from the seeds so let's go check it out so star fruit also known as carambola is a wonderful tropical fruit from Southeast Asia and it gets its name because if you look at the cross-section here it has this perfect star shape which I find really cool star fruit is probably what a favorite tropical fruits to eat because it has this wonderful crisp juicy texture and it has a sweet slightly tangy flavor that it almost tastes like it's mixed with flowers it has a very floral scent or a floral taste to it that's really hard to describe until you've tried one but once you do it'll probably be one of your favorites as well so what I'm gonna do is I'm going to try these out for y'all I'll give you a lot of taste test to see if I can give you a better description and once we get inside I'll show you how to get the seeds from these how to plant them and how to grow your very own star fruit tree at home so let's get to it so I did a little cross-section here just to show you this star shape a little bit better and I usually don't cut into these because as you can see you can easily cut the seeds in half but I just want to show you that and kind of show you what it looks like on the inside the way I usually eat this here is I just eat it like you would maybe a nap a pair just glided into it oh yeah it has so much juice and it's so messy probably the juiciest fruits I've ever had it's kind of got maybe a slight apple or a pear note to it mixed with some kind of like flowers or something tropical to it it's really hard to describe but it's again one of my absolute favorites oh you're so good so refreshing if I could eat this every day here in the summer I would be so happy so I'm gonna eat into this and when I get down to the seeds I'll show you what it looks like all right so I've eaten all the flesh away and on the inside you have kind of this cord that has all these little seeds inside and there's probably I think five lobes for each point in the start and in each of those lobes that's where you're gonna find your seeds and I think these are a little bit immature maybe but I've got another fruit to check here in a minute that's what your seeds look like they're these kind of little round brown seeds but we're gonna get these out and I'll show you how to get them all planted up now one of the other main reasons why star fir is one of my favorite fruits is because of how easy it is to grow all it takes is to get your seeds from your fruit that you get and just get a good quality potting soil and it doesn't even take a large pot to get them start in something like this will work all you have to do is take your seed and plant it probably Oh two three inches or so not very deep doesn't take a lot and we're just gonna give this a good water after about a week or so you're gonna start to see your seedlings come up and they'll have kind of two little cotyledon sprouts that's the technical name for the first two leaves that come out and then it'll start to grow it's normal average leaves and after about a month you're gonna end up with something that looks like this and I love the way this looks it has a wonderful tropical feel it has these compound leaves and one of the fun tricks about this is it probably won't do it right now but it actually responds to touch so when you touch the these leaves they'll fold down in response and let me show you what your tree will look like here in about a few months or so when it's a little bit more mature so check this out you guys this is a more mature star fruit tree that I grew from seed probably about six or seven months ago and these are one of the fastest growing fruit trees I've ever seen I mean look at that I want to I want you to try to think of some other fruit tree that will grow that fast in just a few months but I'm actually going to take this tree and get it crafted so where we can get fruit a one or two year period instead of waiting for it to fully mature and produce fruit on its own I'm actually gonna do a video on how to graph fruit trees where we're gonna graph this star fruit tree and a mango tree and an avocado tree I'm gonna have a guest come along and show you how to do that in the proper way but I think that's going to be all for this video if you like this video be sure to hit that like button if you have any more questions for me on how to start your own star fruit tree from seed leave it down in the comments and if you haven't done so yet be sure to subscribe to the channel that way you can be there for all the new videos come out until next time I hope you'll join me right here on the more you grow see ya

Please explain how to update or paint kitchen cabinets; half idiots guide

we want to show you a quick cheap and easy way to upgrade a bad kitchen cabinet into a nice elegant open-faced kitchen cabinet we started with a dreary poorly painted section of cabinets with three doors and one vertical slide we remove the ugly doors and vertical slat one problem you may run into when removing the doors and slats is it will leave holes and gouges in the remaining parts of the cupboard that you want to keep and in our case when we took out the vertical slat it was held in with dowel pins which ripped a large chunk of the bottom edge of our cupboard completely out but all you have to do is keep the chunk and use wood glue to piece the chunk back in as far as the rest of the gouges holes and marks left behind you can quickly and easily fill them with spackle we picked up a little jar from our local hardware store shop local and when applying the spackle you don't to be shy you don't have to worry about making a nice smooth masterpiece just get it filled in above the depth of the Gaucher hole that's all you need to do then take some 220 grit sandpaper and sand all the surfaces a little bit to just rough them up and then sand the spackle surfaces until they are completely smooth and give the whole thing a nice wipe down with a damp cloth or a tack rag to get all the loose dust off of it can't paint dust masks Oklahoma next mask off the inside back of every shelf we are painting the backs of each show we wanted the insides of our cover to be dark so we use what we had lying around because it's free flat gray exterior it doesn't matter that it's exterior nobody's gonna call you out on it no one's gonna walk in your house and say hey we're interior and that's exterior paint if you have a super steady hand and want to save time by not masking you can try to use a small brush to edge all the services that you want dark but go slow and load the crap out of the ends of the bristles or you can get one of those awesome dumb sponge brushes like this with a perfectly straight end and load that end up and simply push it up into or just masks the whole damn thing that's among people dude the point is you only want the inside backs of each shelf painted with a nice edge we applied two coats of the dark then repainted the rest of the shelf with flat white and added back two slaps on the face to balance the whole thing out this project took us one full day about eight hours but most of it was waiting for the glue and spackle to dry it's pretty simple thanks and as always subscribe

Please explain how to rebuild a motorcycle shock

in this video i'm going to show you how to rebuild the shock on your motorcycle rocky mountain has the parts you need to do the job right including a variety of shock oils and seal kits general tools are required as well as a few specialty tools we're going to need a tusk seal bullet race tech seal head setting tool tusk shock preload adjusting tool and in some cases the tusk shock reservoir cap removal tool to start i'm going to spray a little bit of oil on the threads of the top of the shock and then loosen the top lock nut it's a lot easier to do on the bike and i'm going to pull my exhaust take the seat off and then the tank now we can go ahead and loosen the air boot on the back of the carburetor loosen the lower subframe bolts and then we're going to remove the upper subframe bolt all together this is going to allow the subframe to drop back a little bit giving us better access to the shock now we can remove the lower bolt and nut from the shock once that's out the swing arm will drop and then we can remove the nut washer and bolt from the upper shock hold on to the shock while you remove the bolt so the shock doesn't drop once that's out we should be able to remove the shock from the motorcycle if you haven't done it already now is a good time to put on safety glasses if you want to save yourself some work later measure the length of the shock spring this will make setting your sag a lot easier when you're done i like to begin disassembly by releasing the nitrogen out of the shock reservoir then i'm going to loosen the lock nut on the shock and then the lower nut i'm going to do this by putting it in a vise and twisting the spring once it's loose i can push it the rest of the way back with my finger move the rubber bumper down the collar will drop and you'll be able to remove the retaining ring that holds the spring on now in this video i'm rebuilding a cayava shock the procedure for a showa shock is pretty much the same but removing the spring is a little bit different you've got to kind of knock the two retaining collars loose from each other to reveal a small circlip on a showa shock once you use a little screwdriver or pick to remove that little circlip you can separate the two collars and then remove the spring from the shock that's pretty much the main difference between a showa and kayaba shock back to our kayaba shot at the bottom of the shock we have a little seal cover we're just going to use a little punch there's two holes in this cover and we can just kind of tap on those holes to remove the cover and this will reveal our dust seal and the seal head right below that we want to make sure to clean this really good i'm going to use some contact cleaner and a rag and using my race tech seal setting tool i'm going to push down i may have to release more of the pressure out of the reservoir as i push that down it's going to build pressure so i'm pushing the seal head down to reveal the small circlip that holds the seal head in place using a small screwdriver or pick i'm going to remove the circlip and once again i want to clean this area really well it's going to make the removal of the seal head a lot easier if it's clean at this point i'm going to remove the valve stem i could have done this earlier but i'm going to remove it now and i'm going to mark the location of the stem in relation to my shock body makes it easier to set up when i'm done now i can push the bladder into the body of the shock and this is going to reveal the circlip that holds the bladder in place so once again using a small screwdriver and pick i'm going to work that circlip out sometimes these are a little tricky they take a little bit of patience once that's out again i'm going to clean this it's going to make the removal of the bladder a lot easier if it's clean i'm even going to use a little bit of air on both of them to make sure i don't have any dust with a rag over the sill area of the shock i'm going to carefully move the shaft of the shock up and down and work the seal head out of the shock dump the oil in a pan and following the seal head is the piston and valve stack now i'm going to work on removing the bladder wiggle this back and forth and then with the bladder out i'm going to make sure all the oil is out of the shock on many shocks it may be difficult to get a hold of the bladder cap to pull it out the showa shock shown here has a bladder cap that sits into the reservoir of the shock if you have a shock with a centered valve stem like this the tusk reservoir cap removal tool threads onto the valve stem and allows you to pull the cap and bladder out easily with the bladder out go ahead and clean the body of the shock i'm going to spray it out and wipe it out with a clean rag and then i'm going to wipe off the bladder as well to remove the seal head we have to remove the piston and valve stack and to do this i'm going to wrap a rag around the piston and the valve stack i'm going to wrap a little bit of tape on it to hold it tight the shock shaft has been pinned on the outer edges and on the center hole the goal is to grind the peened edge off the nut so it can be removed on many shocks especially showa it's important not to grind the peening around the center hole this painting keeps the rebound seat in place once you have ground the edge on the shaft around the nut remove the rag and then remove the nut once the nut has been removed i like to get a screwdriver set it in the end of the shaft and pull the piston valve stack all the washers off together that way i can't get them mixed up there are a lot of washers here these are used to control your valving and you don't want to get those out of place then we can go ahead and remove the seal body and the little cap on the end and since we ground the end of the shaft it's a good idea to take a small file and just make sure those threads are clean using compressed air i'm going to clean the shock shaft and i'm going to do the same to the piston and valve stacks in preparation for assembly on my right i have an all balls brand shock seal kit it's the complete seal head assembly so it makes changing the seal on your bike convenient we also sell seals and dust seals separately and these can be installed on your existing seal head to do that we're going to pop the rubber o-ring out of the back side and then there's going to be a washer and then the actual oil seal carefully pry that out with a screwdriver pay attention to how it was sitting in the seal body there's another washer underneath we're going to clean that real well and then using a screwdriver we're going to pry the dust seal off the top now we can install the new dust seal we're going to put some grease on it and then press it on to the seal body since this has a steel frame it's pretty tight so we're going to use a socket to tap it on once that's on we're going to reassemble the oil seal put the washer in oil up the seal put it in flat side down and then the other washer and then the rubber o-ring that sits right on top and holds everything together so now we're ready to start assembling the shock you'll notice on the shaft this edge is very sharp that's where the seal bullet comes in handy slides over the end and kind of removes that sharp edge this will prevent you from cutting the new seal go ahead and slide the seal cap on and then the seal head assembly carefully slide it over the bullet and onto the shaft with the seal head in place we can remove the seal bullet and install the piston and valve stack so putting the screwdriver back on the end of the shaft i'm just going to carefully work all the little washers into place since i've kind of moved them around it's tricky lining up the center hole on the shaft but keeping the screwdriver on everything keeps everything in order so you can't mess anything up once it's in place we're going to install a new nut with high strength thread locker go ahead and thread that onto the shaft and then we're going to torque the nut down to about 35 foot-pounds once that's on wipe off any excess thread locker and just to be safe i'm going to put a couple punch marks between the nut and the shaft to work as another locker to make sure that nut doesn't come off at this point i want to loosen the compression adjuster all the way out this makes oil flowing between the reservoir and shock body a little bit easier so i'm going to pour a little bit of oil in and i'm making sure it's running through to the reservoir if not i'm going to tap it a little bit this will push the oil through and make sure we don't get air caught in between then i'm going to fill the reservoir about halfway and install the bladder you want to make sure you have enough oil in that it's pouring out like this that way you know you have enough you're not getting air stuck inside i have a pan underneath to catch all the excess oil and i'm just going to push the bladder and bladder cap down into the reservoir just far enough to reveal the little groove for my c-clip and i'm going to put the c-clip in place and notice i lined up the valve stem with the little mark on the reservoir there i'm going to install the valve stem using the tusk suspension pump fill the bladder to 40 to 50 psi this will allow me to safely see the bladder cap seat as well as allowing the bladder to keep the correct volume in the reservoir while installing the shaft and seal head a bicycle pump can be used as well but this tusk pump has a convenient pressure gauge built in do not use high pressure compressed air now we're ready to install the shock shaft and seal head we're going to fill the rest of the shock body with oil close to the top and then we're slowly going to work the piston and valving into the shock once it's in we're going to pump the shock up and down you're going to see a lot of bubbles come up might start foaming let that settle a little bit until all the bubbles are gone once the bubbles are gone we're ready to push the seal head into the body of the shock so we're going to top off the shock with oil and then we're going to push the seal head down into the body you're going to notice you can only push so far and then the pressure won't allow you to go in anymore so we're going to have to remove the valve stem again using the race tech tool we're going to push the seal head into the body we want to make sure we push this in far enough to expose the circlip groove again once that's exposed we can install the clip install the valve stem and then pump a little bit of air into the shock just enough to see that sill head seat once the seal head is seated go ahead and put the cover back on might have to carefully tap that on with the mallet once that's in place we'll make sure the shock is clean get all the oil off of it and then we can put the spring back on slide the spring over and then the different collars you'll have to move the rubber bumper out of the way again hold the spring up in place and then tighten the lower nut to the spring continue to tighten the spring until you reach the spring length you started with before disassembly the final step is to release any air pressure in the shock and then fill it with nitrogen only qualified and certified technicians should charge the nitrogen most shops can do this for a small fee install the shock on the bike and you're ready to ride rocky mountain carries a huge inventory of oe and aftermarket parts and accessories for your machine call us or visit us online at rockymountainatvmc.com

Please explain how to fix excess lipase (part 3)

hi welcome back to what like this is in case you had any more questions on it or if you haven't watched the video that I made before this I'll put it in the link down below that way you can go and check it out but I do all of this process because I have excess life as in my milk like this is an enzymes that you have in your mouth that breaks down the fats that way your baby can digest it when you have excess like this this starts happening a lot quicker so that's why your milk starts breaking down before your baby can even have it and that includes when it's frozen the process doesn't stop when it's frozen however you can inactivate it at a high temperature so that's why you scald your milk you don't want to boil it which is why I do it like this because I feel like I have more control over the temperature then on my stove but by scalding the milk you do lose a little bit of nutrients but it's still not losing all of the nutrients in it I would still prefer to do that so if you're not sure if you have excess like this in your milk the best way to do it is a taste test it smells kind of funny or your baby's not wanting to take a bottle when they're away from you that could be it it could just be the nipple itself at the bottom of the bottle that the baby doesn't want but I didn't figure this out until it was too late with Jackson and I didn't do this before pumping my milk so all of the milk that I had it was already tasting like this and he would not take it Liam on the other hand he never had a problem with it I had discovered that that's when it like smelled funny afterwards and I just thought that maybe I wasn't storing it correctly even though I had put it directly into the freezer I thought maybe I just had done something wrong I still threw out all that milk anyways because I thought that it was bad I'm getting greedy to scold some milk for my daughter right now to freeze like I talked about in my last video and so if you want to see how I do it so that way I can remove all the excess like that's in her milk please keep watching I have here so now kind of just finished pumping today it was kind of sad because this five ounces that I pumped out here it took me two tries from both sides and I've been struggling so hard to try to keep producing enough milk to keep feeding Gracie um at this point I'm only feeding her what I'll do is I'll feed her first breastfeed her first and then I'll give her formula and it's usually because she's crying because she's hungry I've just i'm not producing enough milk right now I've changed my diet I'm taking supplements I've been trying everything I think I'm just I've been stressed out had a lot of stuff going on in my life right now and I think I'm just so much more busy this time so it's been really hard trying to cope with having to switch over to formula not but it's a bad thing but it's just not what I wanted to do for so I'm just gonna show you guys what I do so these are the things that I use to scald my milk so that way I don't have to do it on the stovetop the bottle warmer this one is the Munchkin brand I'll see if I can find a link for it and put it down below um some kind of a metal container I don't work on my glass just because you're going to be getting it up to 180 degrees so it could break and that would just be bad then you have glass and breast milk and would be a total waste so some kind of stainless steel cannister you can use like if you have a thermos or something as well I have this from back when I used to bartend and also you need a thermometer I had a digital one but it actually just busted so I'm gonna use this good old like like a meat thermometer and of course your milk and then you're gonna want to have like some kind of container because you're gonna do like an ice bath and dunk it in afterwards to cool it off so it doesn't keep processing okay so I just set it now I'm gonna let it start doing the thing I get like a big container like this and I'm gonna fill it up with some ice water because when you're done you want to dunk it and otherwise it's gonna still keep heating up with in boxing with still on it so your kids may just start pushing buttons when you stick it into the water remember that the water is gonna rise all around it so you don't want to fill it up all the way because I'm what's gonna happen especially about open container like mine the water is going to start pouring into it I know this because I've done it before and I wasted it was like ten ounces of milk I was so upset so make sure that you don't fill it up all the way because then you're gonna have a problem that I did I wanted to show you guys make sure you're reading your meat thermometer right I've done this before in the past you see how right here you can see the tip it looks like if it's getting to 190 but you have to remember that tip is not that you need to use this side I'm not sure that the site is called but this part should be at the bottom so really it's only getting to about 120 degrees right now I've made that mistake before and I froze a bunch of my milk thank him that I had heated it up to 180 degrees when really I had only heated up to a hundred so make sure that you are using your thermometer crackling it around just to make sure I'm getting an accurate temperature I'm just going to take it off for a minute because it was leaning up against the sides so I don't want to get encouraged to do this method you need a bottle warmer that won't shut off automatically a lot of bottle warmers have like a safety feature somewhere you don't leave it going but that won't work with this because it will cool down on you then you have to turn it back on and it's just gonna have to keep going and going so the one that I use I looked up online did some research not one doesn't have an automatic shutoff it does up to ten minutes so you don't even need ten minutes to be able to scald your milk I've been able to do it with cold milk from the fridge and maybe about five minutes sorry she's here background noises my kids once it's done then put it in here you can start to see the temperature dropping usually I let it sit in there for a little while I'll probably put like a cover over it that way nothing gets into it um but yeah once it's cooled off then you can put it into like a storage bag and you just put it into the freezer and you're good to go and so that's how you can keep the milk from starting to like taste bad also I wanted to mention and if you discover that you do have excess like this and you already have a bunch of milk in your freezer and your baby's not taking it before throwing it out you can consider donating it I wish I would have known this at the time because I totally would have donated it but donated milk can go to babies who are eating through a feeding tube that won't even notice the difference so that way they can still get the nutrients of breast milk but they won't be tasting how bad it tastes anyways so they'll still be able to benefit from it this is cold off now we're going to pour it into the bottle you can pour this directly into the storage box as well if you like this one I'm probably gonna be feeding her soon so that's why I don't put it into a bag thank you guys for watching if you haven't already please subscribe and if you like this video give me a thumbs up that way I know that you liked it so I can make more videos like this and also if you have any suggestions please leave it down below or also you can find me on Instagram I'm pretty active on there you can get ahold with me DM me if you guys have any questions or you have any requests I'd love to make a video just like this one that was requested that way it's something that you guys actually want to see I'm looking through YouTube right now because I'm trying to see any other videos on this there was one video that I remember that I had watched when I figured out that I could like scold my milk like this um there's still not a lot of video so it's only like a few of them and it's from like three years ago which obviously the process would still be the same I mean I haven't found any updated information but I can't be the only one who's going through this and maybe there's just moms out there who don't know that they can do this maybe they all think too that their milk was bad and they're throwing it out I hope not it I asked the cheaters share this video that way we can reach as many mamas as possible because maybe there's a lot of other ladies that are going through this that they just don't know what they can do about it um I don't know about you guys but I don't ask my mommy friends what is your breast milk smell like what does it taste like after you've pumped it it's just not something that I talked about that their mamas I mean it'd be great to see that but I actually don't have that many friends to breast feed at least friends that I know well enough to ask how their breast milk smells so I think would be a great idea for everybody to share this or at least talk about it with your mom friends maybe they're going through it and there's a solution that they just don't know about yet if you have any suggestions or any comments to add to it please leave it down below in the comments and we'll see you in the next one why do so Jackson you said my house is a crazy house the tttttt baby shark tttttt baby Shakti TTD baby

Please explain how to clean vintage gold plated tie clips

hi welcome to the Thai chest today I'm going to teach you how to clean a men's gold-plated tie clip so here's an example of a vintage gold-plated tie clip and the thing with these two clips that have the gold plate is that you can't use a standard jewelry polishing cloths like this one because it's actually gonna take the plate right off and here I have an example to show you here here's a tie clip that's supposed to be all goals if you turn it over it's all gold but somebody's taken a polishing cloth to it and you can see it's all silver all of the the gold plating is wearing off here so somebody probably went to town with the polishing cloth there so don't use a polishing cloth on the gold plated stuff another thing this method is not going to work with any kind of tie clip that has a stone I'm gonna show you a different method to to clean those ones so this method is good for just any kind of plain tie clips with no stones on them gold plated so here's an example before we get started here's what you're gonna need some soapy water I just use plain dish soap some clear water to rinse some toothpicks and some cotton swabs as well as a soft toothbrush and towel to dry okay so first thing is I as you can see this one's a little rowdy it's just kind of got some some some oil on it take a toothpick I love using toothpicks and I just run it through the grooves here sometimes you'll notice the metal is worn sometimes it's just dirt so just get all that loosened up here be careful where it's black here I usually don't pick too hard there because sometimes the black stuff comes right off and I think it's meant to be there for decoration alright just get it loosened up a little bit you want to give this piece a little bit more shine on it to get its luster back okay so once you've loosened the dirt just go ahead and immerse it in the soapy water and this method was actually shared with me by a well-respected jeweler in this town so comes from a good source I didn't just make it up I'm just gonna give it take soft toothbrush maybe a good a good clean and then you want to rinse it in the clear water and most importantly you have to dry it so the drawing part is really really important because you don't want that spring to rust out and a trick I use two things I usually open it up and clip it like a tie to the towel that way I get all the inside nice and dry there's also one more nook and cranny here right in the back underneath I usually use a cotton swab for that just make sure the spring is nice nice and dry there you go so you can see it looks a lot better now it's a little more shiny and it'll the best of all it's not going to leave any dirt marks on your tie when you go and put it on so I hope this video has been informative if you are looking for great pieces of men's vintage jewelry or some awesome ties check us out as at HS calm

Please explain how to defrost frozen bread in 5 minutes without a microwave

okay we can do this yesterday Noida spread I'm so hot here in Brisbane Australia dad it was frozen say play a little bit there's four pieces and it's frozen a girl now let's say with the camera and give the to five minutes for the first and again it's cool to to hear we're gonna wow that is really disgusting well hmm okay I'm convinced and the temperature is 30 degrees in the kitchen here and it's fully defrost them Wow so who needs a microwave that's astounding okay now you know what to do come to Australia and defrosted bread

Please explain how to

how to roast coffee beans with a popcorn popper we're using today the West Bend popery one available on eBay for about 30 bucks it's the first version heavier duty with more wattage it's a little bit cold today so we have it inside of a box to help maintain the temperature so let's go ahead and plug it in good to let it run for a few minutes to preheat the popper for more even in quicker popping what we've got is some green Sumatra beans you can see a person they start stuff that's coming on outsider to be it's going to reduce in weight and the beams are going to bounced around a little bit more we're starting to even out the top and bottom distribution of the beans so the bottom ones don't get harder than the top one but as it progresses they Framus do that about a minute into the roast the beans are starting to take on some color that lone black bean you see in there is is closed now we are entering what's called the first crack and you can barely hear it in this video but it does make a very light popping noise once the beans get going before the fluency 3 inch aluminum ducting reducer in there to keep them from popping out now we're at the second crack at this point you'll begin to notice [Applause] a little bit of smoke coming from the roasting once the beans are at the desired roasting levels what you want to do is kill the power and pull them off as quickly as possible so we're going to pull the plug and pour them into a colander and take that colander and put it over a fan if you've got it right we've got a squirrel cage blower from a wood stove but any old fan will do getting the beans up to temperature as quick as possible and cooling them down as quick as possible we have found is key to the best flavor you want to continue this process until the beans of cool down to room temperature okay once the beams of pulled we will turn off the blower and sift through them to see if you can find any unevenly roasted beans occasionally there will be a few and discard them this roast isn't perfectly even but with practice and you can get a little bit better and now that they've cooled down to room temperature we want to transfer them to a storage container these little units can be found at any kitchen supply store they look really great for keeping your beans in an airtight enclosure and then label the top with the variety and you're roasting date will have to delete these and put on what's proper

Please explain how to make choux pastry for eclairs - hansells

hi i'm robin martin today we're going to make choux pastry choux pastry is used to make things like chocolate eclairs cream puffs and of course that mazing french wedding cake croquembouche so I've got a hundred grams of butter here and I'm adding one cup of water and I'm going to take this to the stove and it's going to come to a rolling boil so fix that up and away we go a full rolling boil is when the mixture boils all over not just at the sides when the mixture has come to a full rolling boil remove from the heat and add the flour all at once mix that in and beat it with a wooden spoon until the mixture comes away from the side of the pan you'll see it forms like a ball look at that so that is ready to be set aside now to cool down slightly because if you don't call it an add your eggs straight away you will scramble the eggs and the choux paste will be a disaster when the mixture is cool enough add your eggs one at a time and beat well after each addition beat it until the egg is combined into the dough so you can see one here combined add another egg so our last Eggers mixed in at this point you can actually transfer your mixture to a food processor but needs to be a strong one with a big motor or a heavy-duty cake mixer this sort of cake mixer is no good what happens as the mixture goes up and gets stuck on all the beaters the engine on this is not grunty enough to deal with the thickness of milk mixture if you're going to use manpower jumper to beat this that's great but take it off the board now that the pot has cooled down and put it onto something like a dish cloth or something and that holds the pot firmly to the bench now comes the bit that you wished you'd been to the gym for three weeks beforehand because you've just got to keep beating this until the mixture is smooth and glossy now we're ready for shaping you can actually use teaspoons and make little cream puffs out of this mixture or you can use a piping bag and make chocolate air clear shapes with long ovals or you can use your teaspoons to make long shapes actually easier though in a piping bag so fold your piping bag over and get your mixture and I'll probably find it easier to use a rubber scraper to do this look at that beautiful shiny mixture then just work it down on the bag now if you want to be really really precise on the back of your baking paper you can draw lines and that gives you a guide so as each thing is the same length but I find that once you get into the rhythm of this you you find that it's actually just easy to go down like this and click it off alternatively if you don't want to use baking paper it's very gooey to finish off but you can actually just put these onto a greased baking tray so you can see you get into the rhythm of it I've tried using a knife to cut it off I've tried using scissors a good clean finger is about saying or you can just do little cream puffs or you can do little circles but if you're going to do the circles I would really recommend that you actually draw a circle on to follow so once you've got your choux paste made you can make just about any shape you want depending on what occasion you're serving your eclairs or your choux puffs or your choux pastry you can make them any size I've made some small ones here and I've made some larger ones also choux paste Rises by steam so when you take it out of the oven it still got some steam trapped in there it's really important just to cut a little slit on the side of your shoe paste and that lets the steam escape so they don't get soggy on the inside leave them on a tray to cool once you've put the slit in them and when they're cold you can actually store them in an airtight container or you can put them into a plastic bag and suck out the air and keep them for a number of weeks before you are ready to use them for these and more great baking ideas go to Hansel CO NZ

Please explain how to give an awesome best man speech with ideas for a funny & emotional wedding toast

Welcome back to the Gentleman's Gazette and our wedding series.Today, we discuss how to write and give a best man's speech. Congrats! You've been asked to be someone's best man and that entails a lot of things including giving a best man's speech. No pressure, but it's a big deal! Once, I was in a wedding and the best man's speech was given by the brother of the groom and it started out with "Growing up, I never thought my brother loved me" and at that moment, everybody paused, was embarrassed and it was just a huge let down and it ruined the entire evening. Now that was terrible, your goal is to give a heartfelt, funny, appropriate, and unique best man's speech that most importantly is not too long and to the point. Most impoprtantly, Prepare your speech in advance because I've never seen one that was given off the cuff that was actually good, to the point, or funny. Usually, what ends up happening is just people ramble on and it's way too long. Write it down. If you're not comfortable speaking in front of people, it's a good idea to start with word by word but you don't want to have more than one piece of paper or one card so I suggest to bullet point your speech because nothing makes people less interested in the speech if you have to flip through pages. Most importantly, Be yourself. If you usually don't joke and you try to crack jokes, it's just unfunny and superficial and people won't buy it so be true to yourself and it will be a good speech. Be sober enough to deliver your wedding speech. There may have been toasts before, you may have had a drink and that's okay but I remember a wedding once where the best man was absolutely drunk and he just made inappropriate jokes, slurred, rambled, and it was just a general embarrassment. Don't be that man. Make sure to mention the bride in there and it's not just an ode to your friendship, maybe you can have a little story about how they got to know each other or how you learned about her from your friend, something that incorporates her and makes her shine in a positive light. Very important, be tactful. Don't talk about the groom farting, don't make any dirty jokes, don't talk about sex, or exes, or anything else that could embarrass his grandma, not him, his grandma! Keep your speech short and to the point, because otherwise, people won't pay attention and honestly, no one really cares. People want to be entertained and five minutes is the maximum attention span. I know, it may look like five minutes on paper but actually, the best way to make sure you hit that goal is to give your speech, you can either talk to the mirror and time yourself with a stopwatch or even better, give your speech to actual people so they can give you instant feedback. That way, you know how long it took you whether it's funny or not, inappropriate or too crass, and that way you ensure you'll deliver a perfect speech when it matters. So what should your speech look like? I'm a big opponent of giving you a cooking recipe because that's too static and it's important that your speech has a personal touch. That being said, there is a basic framework that works for most best man speeches. So what should your speech look like? I'm a big opponent of giving you a cooking recipe because that's too static and it's important that your speech has a personal touch. That being said, there is a basic framework that works for most best man speeches. Introduce yourself. Tell the audience who you are and how you know the groom. Thank everybody for coming, thank the people who made it possible if that's not just the bride and groom and just make sure everyone feels welcome. Explain how you know the groom and what your relationship is to him. Come up with the story of how you got to know the groom and/or how you learned about his bride and how it all goes together. Ideally, it should be a little funny or at least entertaining maybe with a little twist. Maybe you also have an interesting incident where you maybe asked him how did you know she was the right one, and you remember that answer. Just something that's heartfelt and touches people. Now if you want, you can thank people for coming again but more importantly, thank the couple and send them your best wishes for the future. It's very important to have a common toast to the couple and their future. With this framework, you'll be able to stay within the 5-minute mark, have a really good best man speech that is well-remembered and respected and thought of fondly in the future. To learn more about things related to weddings, such as what to wear, dress codes, how to get a wedding band or engagement ring, stay tuned!

Please explain how to ride corner jumps on a cross country course

hello I'm Olivia welcome to equestrian coach comm today we're going to talk about corners on the cross-country course and we're going to spend some time talking about how you'd introduce a young horse to jumping a corner and then get into some of the more technical questions and technical ways to jump a corner later on you'll notice that I've set up this corner in a way that it could be broken down to be very small we can turn those blocks over and it could become a very small jump the reason that I do this is because then if the horse doesn't understand it's really easy to simplify the question for them so you see I jumped the vertical let him go forward so then I'm really holding him into the base of the jump he's got a jump to jump straight holding him on that line and again thinking about where I land and where I go away from the jump

Please explain how to make vegan ice cream floats (kombucha float)

guess what we're making today first you will need to get a jar or a cup i'm using a mason jar to put your delicious ice cream in today we are using the coconut bliss ice cream it's dairy free then to that you will add your favorite toppings we're using gone nuts and some hibiscus dry flowers and I love the coconut bliss because it's really creamy and it happens to be non dairy which is really delicious so you add us a scoop of that then you add your favorite topping i'm using hibiscus flowers or dried it's are like really crunchy and sweet these nuts gone nuts with chocolate cashews almonds and cacao nibs we're going to pour this kombucha it's supposed to like whoa whoa and there you have a kombucha looked really really really it's actually one of my favorite desserts I really don't like people watching me while I eat but oh all that crunch not since 80 mark my words I hate coffee ice cream first of all of it this is like a natural video where everything happens like like real life look at this spill look at the epic spill their lies how this is like how it really happened giving the Buena Vista sleep they taste like they all taste like chocolate chips we know you want it this brand is sugar like doesn't have processed sugar in it so it's like we're fine sugar yeah some of their products some of their flavors do so we walk here

Please explain how to make a candy cane striped friendship bracelet

hi everybody today I'm going to show you how to make a candy stripe bracelet what you're going to need is at least three colors looks better with like six or eight strands I have nine when you have your color order set up what you're going to do is start on the left hand side with your first and second strings so pink goes over purple like a number for underneath pull it through 12 knots on each string put the purple to the side and then you're going to take your next string and you're going to put your pink and number four over the blue twice this is called the floor would not this is basically the simplest friendship bracelet you can make all you do is like make number fours with your strings all the way across when you get to the very end you just repeat it with your next color which is going to be my dark purple the first let's get to the very end friendship bracelets take a long time but they're worth it because your friends are really happy to get them so now I'm at the end and what you do is just leave the dark purple at the end I mean dark pink at the end take your purple and start over again with the forward knots I hope this helped you guys out if you have any questions feel free to ask um if not have a good day and thank you for watching so now you're at the end and your last pink from your last bro you just take and kind of pull it down and wrap your purple around it oops and now your Purple's at the end and you can go straight down it's pretty simple thanks for watching

Please explain how to remove stuck key from ignition 2017

hey YouTube how you doing ah actually I just drove came and parked and I've been struggling to take this key out struggling to take this key out for the past 30 minutes and nothing is walking I've been struggling and struggling but if your key get stopped in the car this is the way you solve this problem what you need is a screwdriver get a screwdriver like this you move to the bottom of the car of this steering and you take this out you see this you take it out and what do you do is you seen your finger right inside there's a little toggle button you're gonna press that down and if you press this down a little bit and then you just wow you see you got so you just hit this button and once you take this out you just hit this little toggle button and it turn it out and you see you solve that problem so you can even kick the stuff out you don't really need it you can keep it out there you don't need it anytime you go and it stopped you just send your handwriting and you solve that problem so I hope this helped you out this very important message I just fed it and taught to shared out everybody if you're facing this kind of problem this is a solution all you need is a screwdriver so mechanics are gonna charge you for approximately a hundred two hundred bucks to solve this key stop problem but you know just a screwdriver think you grab this for about three bucks and you solve this problem so that is it please like comment subscribe to our YouTube channel or we just any useful information we have we'll be putting it out there and just to make sure everybody is safe knowledge is power and the application of knowledge is wisdom

Please explain how to screw through carpet

have you ever had any experience of putting a screw down through carpet and this is what takes place the screen thread will pick up the actual to come to the thread of the cutting pulling it and damaging the perfect for good well here's a tip for you that may be a black puttin on the floor on arm in order to hold down a cab and you're using wood screws in the pilot subfloor now the wood screw is quite forcing the thread and this is what you do pick a piece of scotch tape and wrap it around the thread that way when it goes down through the carpet that's not going to pick up the threads how long you go through without any damage but they screw in exactly the same way and down it going nice and tight holds that bracket nice and firm and you know daddy you

Please explain how to make a delicious chocolate milkshake : divine desserts

hi I'm Joseph you seen oh yaara chef and today I'm going to show you how to make a delicious chocolate milkshake three things you need you need milk about 125 Mills it's a half cup three scoops of chocolate about 170 grams six ounces two tablespoons of chocolate syrup that's 30 mils into your mixing container you have your milk pour in your chocolate syrup mmm how good does this look now i'm using a hand-held mixer you can use whatever type you like now if you want a thicker thicker milkshake put more ice cream but I think you'll find this is the tastiest chocolate milkshake here you go a delicious chocolate milkshake I'm in the kitchen of the party penthouse 4040 galt ocean drive I'm Joseph you seen you

Please explain how to install an injector rebuild service kit

welcome to my garage today I want to talk about injectors as you probably know injectors are a very important component of your car because they make sure you get the right amount of fuel at the right time however after 5 10 15 or maybe 20 or 30 years of service you can be absolutely sure that the spray pattern and amount of fuel deliver as well as a consistency of fuel delivery from injector to injector has been compromised this of course affects your engine and engine performance and multitude of negative ways however you can you can improve that when fix any of these problems yourself by buying and installing and injector service or injector rebuild kit they are widely available and you can find it for almost all types of conjectures and they're also expensive and it pretty easy to install as well so here you can see my injector rebuild kit it consists of 4 pintle caps for lower grommets for upper rail spacers for all rings and for micro filters this particular kit is for my injectors that came of 1987 toyota mr2 with a 1.6 16-valve engine these are you can say these are old-school injectors because they have pintle caps newer types usually don't have pintle caps however these injectors are very durable as most conventional type injectors are so if somebody tells you that you need to replace them be sure that you need replace them because often these things can any problems away to them can be fixed by doing doing a installing rebuild kit such as this one or maybe having them professionally cleaned they very rarely fail unlike some very types of injectors that you can find for example indirect objection gasoline or common rail injection diesel engines okay the first thing I'll be replacing are these o-rings and the upper rail spacers now these are very easy to remove all you have to do is pinch the o-ring on one side and then just roll it over there you go the rail spacer is even easier to remove you just gotta basically take it off and that's it you will now take a new wall ring and the new rail spacer first install the rail spacer because otherwise it won't fit over the o-ring as you can see the rail spacer is the same on both sides so it doesn't matter which way you put it up or down we'll push the rail spacer on new ones are much more flexible they also aren't brittle so they take a bit more of an effort to to push on okay here's the new o-ring installation is again simple just roll it over okay that's the easy part the next part is removing that Pinto gap okay depending on the injector and the and the condition of your Pinto cap you can sometimes remove your Pinto camps with hand just by pulling them off since my injectors are almost 30 year old 30 years old you can see the Pinto cap is completely discovered and it's also so old that you can actually remove it with just a bit of strength there you go now when replacing Pinto caps the part that you really have to be careful about is this little needle now you do not want to damage this part because if you damage the needle you will need to replace the injector okay we'll now take a new pintle cap and as you will soon find out it will not go all the way down because it's a new Pinto cap and hasn't been basically worn out of shape like the over what you will need to do with this one is heat it up just a bit and then push it over okay okay I'm going to go ahead and use my use my heat gun to just heat up the Pinto cap a bit so I can push it on to injector onto the injector you can probably do this with a with a hairdryer or something we could run a heat gun but this is a bit faster and it's going to get the job done so just going to get a bit noisy so okay here we go because this thing this thing gets a bit hot I use the old Pinto cap to push on the hump inter-campus out of my fingers but there you go as you can see the needle protrude just aside a bits side oh it's slight bit so be careful when you do this okay the the our grommet is also very easy to install as you noticed my injectors didn't didn't have these they were actually so brittle and all the day basically disintegrated these are the new ones the narrower end goes on the bottom and the wider end goes towards the the wider end of the injector so just pop it on and there you go looks better already that's part it needs to be replaced and the injector is is this little bit which is inside it's the micro filter as you can see getting at it with your fingers is almost impossible but I'm going to show you how to do that in just a second to replace the micro filter you will need to find a screw that fits just right and screws right into the micro filter and put it in a vise now when replacing the micro filter be sure not to get any foreign matter inside the injector so get a new set of gloves or make sure your hands are 100% clean so I'm going to go ahead and screw the filter onto the screw that's it you don't need to go too deep and then I'm just going to I got and there you go it's off and you can see it's empty you'll now get a new micro filter put it in and give it give it just a very light tap with a hammer there you go one brand new micro filter is it and there you go that's pretty much it the o-rings the spacers two grommets the pintle caps and the micro filters thanks for watching make sure you get it right amount of fuel with the right time but after but after a while 510 or in my case in the 30 years of service the injectors have simply holes there

Please explain how to make deluxe jordan almond flower wedding favors

hi this is Beth it Jordan almond flowers calm show you how to make a deluxe Jordan almond flower wedding favor this is a white on white version I'm going to show you how to make this one the supplies you're going to need are some almond holders five of them Jordan almonds five M relieves pearl sprays some white rose leaves these are also available in green we're going to use white for this example and a floral accent for the center these are white pearl roses but you can use almost anything for the center and we're going to need floral tape and some ribbon to tie off onto the stem now first going to take your almond holders place a Jordan aa minute each one is place it in the center and fold the omelet holder in half and you're going to make five now I'm going to hold one on and holder like this I'm going to just bend it backwards take a pearl spray and just line it up right next to stem to stem then our floral accent for the center we just twist the stems together and you can adjust as you go along I'm going to take our other almond holders and place them all together in a small flower bouquet just twist all of the wires together I'm going to tape it off with floral tape just wrap it around the base then we can adjust it a little bit I'm going to take the rose leaves I'm going to place them underneath the base of the almonds in between each almond each wire stem around the base and for the deluxe flowers I use five Rose leaves and then to finish it off we're going to take the floral tape and wrap the entire stem just spinning the flower and wrapping the stem all the way down and then all the way back up I'm going to take some satin edge organza and wrap the stem and tie a bow again you can find all the supplies that you need until including different colored comment holders and Jordan almonds and flowers on Jordan almond flowers calm

Please explain how to clean a clogged drain - slow bath drain

I tried this new tool the other day it's called the drain claw removes hair and they say you can also use it like a mini rod and I I unplugged this sink here and I was amazed at how well it worked I wish I would have filmed it but let me just show you what we did you're able to take this tool and push it right past the pop-up and as you rotate it you're able to pull out here now I clean this out there that deal is amazing how much hair was in here but not only you can put a little bend on it and not only does it pull out here from the pop-up but it goes all the way down to the p-trap and it actually goes up and into it and it breaks loose any debris or any build-up inside the trip and I was just amazed at how well it worked and so I grabbed an old tape and laying around and you can see how easy it pushes its way through so it does an excellent job now we're gonna take a look at a tub that's been running really slow and we'll see how it works on that all right we've got a slow-moving drain here and we're going to use the drain cloth on it and see how it works so we're just going to insert it down the drain and turn it and that is amazing this was running really slow and look at the amount of hair that this catches just immediately and it really does a great job of hanging on to it you can see that will insert it some more I mean that is absolutely amazing how it grabs and allows you to pull out pull out the hair without a tool like that any any little Nick's inside the pipe any little debris in there will start catching here and really have an amazing build up so you can see how effectively that works we're going to take off the overflow and we're going to ride right down to the trap also and show how easy it is to unstop any clogs any buildup of hair in your bathtub the drain cloth does an unbelievable job alright I remove the overflow and it's just screws to get the cap off and now we're going to use this as a mini rod and we're going to push it down the overflow I'm going to bend it slightly toward the back which is where the p-trap should be pointing and we're going to ride right down in here now we're gonna manipulate it a little bit yeah you can see we're bringing up a lot of debris soap buildup shampoos conditioners and so what our just going to ride back and forth quite a few times and this this amazing little tool not only does it pull out all the hair which slows your drain and it's gonna prevent us from having to use harsh chemicals it's going to clean all this build-up into the trap also so the drain cloth does an excellent job

Please explain how to caulk fast

hey guys are gonna make a quick video this is gonna be a 10 or 15 minute video just gonna get right to the point I'm gonna show you how you can clog faster and that way you're not stopping every every second to clean the clock so so first you want to start at the end find one end if you work left to right right to left it doesn't matter but usually this right here is a two piece baseboard it's actually you got five in the quarter base we're here all the way down and then you have this piece right here which is uh it's like a three and a quarter piece and the reason we did is because the floor here before they went to the baseboard so they left a big gap so for us to go over the floor we you know we did that two piece right there so came out real nice and you actually covered a big gap so back to the caulking these are two piece baseboard so you have one piece here that you have to caulk and one piece here I've seen some people that they do they do you know like a three feet area you know and then they go ahead and clean it the easiest fastest ways to start one end and take you all the way I'm actually gonna run out of cockier so first thing I should have done let's get on YouTube okok go alright so let me pause this alright so we got our fresh tube and I finished cooking down money but I haven't run my finger through it and that's what you want to do you don't want to run your finger to the until you'd done okay so you do you are the line here you finish it right there and I got some more over here and I'm gonna do the same thing and I'm gonna run my finger through it yet coal doesn't drive that fast though so you got a lot of time to work like fast I don't me hours either you know buddy you get my what I mean you got you know at least five minutes before you know you start getting the skin little hardened so I come back into the bottom part yeah it's kind of hard doing it with one hand but uh so once you get to that you know you come back and run your finger through it always have a rag with you know clean up any mess you made before you continue the last thing you want is the homeowners showing up and there's a mess on the floor all right so I should like to start from left to right I find it easier come back into the same thing again but on the other joint and now since you done all that now you can now you can slow down if you like and you can do your you know your your cuts you know your joints in cocktails end but you can really have this whole room done real quick if you don't stuff like that you know though your top know your joints first you know the longer pieces and then then come back in is do your you know you do your joints or you have somebody coming behind you to do the joint of course you know the 45s that you know you know in the middle or something you know cause you gotta pack those up so I hope that helped and leave your comment thank you

Please explain how to make low-carb zucchini noodle dinner!

if you want to learn how to make this delicious zucchini noodle recipe chicken and avocado sauce keep watching ok let's get started you will need two zucchini asparagus a ripe avocado some cherry tomatoes a half a wedge of lemon some garlic some chicken salt pepper and olive oil you'll also need a veggie to help you cut up your zucchini the veg rainy gives you an option to cut your zucchini either thick or thin so to get started you're going to cut off both ends of your zucchini put it in the veggetti and start twisting once you get towards the end of the zucchini all you have to do is grab the top to the veg ad stick it on the end and twist it helps you to twist the last pieces of the zucchini without chopping up your own fingers this is what one zucchini will yield you just want to pick out the core with the scenes and throw those pieces away now I must warn you that you should not make more zucchini than you need for one sitting okay because the peeny is made up of so much water it will get soggy so only cut up enough Sookie need for one meal for one sitting now it's time for the avocado sauce are you going to do is take your avocado and spoon all of the meat out of it then you're gonna take your half limit and squeeze as much juice as you can out of it I was having a little trouble getting it as good as I wanted to so I got my husband to come in and help and he likes to use a little trick where he sticks a fork in between it and then squeezes did you say now you want to add about a teaspoon of salt a teaspoon of pepper and about two tablespoons of extra virgin olive oil now I don't have a food processor but I have a Vitamix so I used that to mix all of my ingredients together on the lowest setting now that the sauce is done I move on to my fresh veggies so I warm up my pan and I put in my extra virgin olive oil and it's garlic I then add my chopped up asparagus and I mix it around I want it to be pretty evenly mixed up after that's all warmed up and it's cooking all good I've been at my tomatoes I don't want them to be overcooked I just want them to be slightly after I'm done with it I set it off to the side to pool and start working on my chicken what I have here is chicken tenderloins and I just put them up into small pieces and season it with seasoned salt and garlic powder I cook it on medium to high heat and it takes about five or six minutes for the chicken to be completely cooked through now it's time to add all of the ingredients together so I just take my zucchini noodles and on top of it I put my garlic tomatoes and asparagus word to the wise when you are using your veg ad stop every so often and break those or teenie noodles apart or you will be left with these really long zucchini noodle strains now on top of that you're just gonna add the avocado sauce and mix it all together after this I'll mix up really good seniors is gonna age your chicken in and mix it up as well and there you have it a delicious of cainy noodle recipes with chicken and avocado sauce I hope you guys have enjoyed this recipe if you decide to try it out don't forget to tag me on Instagram Facebook and YouTube so if you haven't already wrap your free quick tips fitness and food guide subscribe and don't forget to check out my last foodie Friday video talk to you soon guys bye

Please explain how to install a roman blind

this video explains how to install Roman blinds with the cord lock system followed by how to install Roman blinds with the side winder chain operation first the cord lock system to install your blind within the window recess mark the fixing bracket positions approximately 10 centimeters from each end of the recess and intermediate brackets evenly spaced between ensuring they don't interfere with the cord guides on the back of the blind the brackets can be faced or top fixed if top fixing mark the correct position checking there are no obstructions such as window handles which would require the bracket position to be further from the window frame if you are unsure what you are fixing to use a small steel drill bit to determine the material for timber use the wood screws supplied for plaster or masonry use plastic plugs and screws or plaster board fixings for steel use self tapping screws with a steel drill bit all supplied from your hardware store clip the blind into the brackets and ensure the blind is secured now for the side winder chain operation to install your blind within the window recess mark the fixing bracket positions approximately 10 centimetres from each end of the recess any intermediate brackets spaced evenly between if top fixing mark the correct position checking there are no obstructions such as window handles which would require the bracket position to be further from the window frame if you are unsure what you are fixing to use a small steel drill bit to determine the material for timber use the wood screws four plaster or masonry use plastic plugs and screws or plasterboard fixings for steel use self-tapping screws with a steel drill bit all available from your hardware store now locate the track onto the bracket plugs and swing the swivel arms across from right to left to locate under the lips of the track and ensure the blind is secure finally fix the child safety cleat if your blind is to be installed onto the outside of the reset you it's easy when you do it the direct blinds co uk way

Please explain how to make chocolate shake sprinkle shots

hey guys welcome to Ali Shah how to i'm jesse jane and this is heather will make the milkshakes here yes so we're making hardy Hardy chocolate milkshake Shaw as shot alright so this is just milk chocolate chips or semi-sweet chocolate chips you're going to melt them in the microwave at 30-second intervals and every 30 seconds stop take it out and stir it otherwise you will burn your chocolate so it's been alright so here's our melted chocolate perfect it was like one minute 30 seconds and now what we're going to do is take our glasses so did it and like swirl it a little bit Roland put in your own dip in sprinkles okay you think that sounds a bit how key to that right difficulties and then you're gonna let them chill out so we're gonna make chocolate milkshake three scoops of ice cream what 33 it's nice for your milk right into this you want me to do some whipped cream so obviously you want to serve these right away or you can save the glass is actually in freezer or fridge and then while you're drinking it so that is it those are our party milkshake shot glasses with sprinkle rims and they're perfect for kids parties or adult party oh you're watching this video please leave a comment below if you like this video yeah subscribe like well like my venture lay back yeah another will come back yeah and I'll see you guys next time goodbye

Please explain how to make chicken fajitas | hilah cooking

- Hey dudes, I'm Hilah and today on Hilah Cooking, I'm making chicken fajita tacos. This is a great, quick weeknight meal and you can also easily do this on a grill. I'm gonna do it indoors cause I'm kinda lazy. (upbeat music) To make chicken fajitas, you need to get some chicken. I'm gonna use some chicken breasts here and I've sliced it really thinly. If you wanted to do the same marinade and grill your chicken, leave your chicken whole and marinate it for a little bit longer but I like to do it like this, to do it inside cause you don't have to marinate it as long and it's really fast. I'm gonna use a little bit of worcestershire sauce, a little lime juice, and salt, and pepper, and a little bit of oregano and this is just my, this is one of my favorite marinades for chicken. And I know that technically I guess there's no such thing as chicken fajita because fajita is a cut of beef but... Whatever. A little bit of garlic, (playful music) and just set that aside and let it marinate for at least 15 minutes, but up to an hour. Set that aside and then I've got my vegetables already prepped here. I'm using some red bell pepper, some fresh jalapeno, some onion and I always like to add some squash or zucchini to my fajitas just because then I'm getting some vegetables in there and then I don't have to like, worry about making another vegetable. It's really just because again, lazy weeknight dinner. So I'm gonna go over here to the stove, we're gonna heat up my cast iron skillet with a little bit of oil and cook these vegetables in batches. I'm gonna cook the peppers first, and I like to leave them a little bit crisp so just a couple of minutes on high heat just to get a little bit of color on 'em. We'll pull those out, set aside in a bowl, add a little bit of oil if you need to and do your onions the same way. Just cook 'em however long you want to. I again, like to keep them a little bit crispy. Then, we'll do the squash and I like the squash to be a little bit more cooked so we'll let it go longer. But make sure you get some color on it, nice and soft and pull that out and put it in a bowl with our other vegetables. Then add a little bit more oil, get the heat up really hot again. We'll add the chicken and sear it, just put it in in a single layer, drain most of the marinade off and don't touch it for a minute or so. You wanna get some color on there. Flip it over, let it go another minute that should cook it. So it'll cook really quick. You can add the rest of the marinade and just kind of let that boil for a second, we'll add the vegetables back in, get everything coated and then we're ready to make some tacos. It's beautiful taco time! I like to put some cheese on mine and you can put sour cream or guacamole or pico de gallo or whatever and some homemade of my special hot sauce. So I've got a tex-mex playlist if you wanna check that out, I'll put a link below. There's a really, really, really good grilled achiote chicken recipe that I do with my friend Carlos, it's excellent. Much more authentic than this but no less delicious. Taste, taste, taste the taco, taste the taco now. (playful music) I have lipstick all over the tortilla. But that is a darn fine taco! I hope that you try this recipe. Don't forget to subscribe, I'll put a link below. Thanks so much for watching and I'll see you next Thursday with a new recipe video, bye bye! (upbeat music)

Please explain how to make the smurf in the skyy drink (using skyy vodka)

Today we're going to show you how to make a BartendingSchool4Free.com original drink, this one's called the Smurf in the Skyy. We're going to start by putting about two scoops of ice into our blender here and to that we're going to add about half an ounce of obviously Skyy vodka. We'll do a full ounce of Blue Curacao. Another full ounce of Island Punch Pucker. An ounce of freshly squeezed lemon juice we already have prepared here. Then we're going to top that off with a little bit of Sprite. Mix that up. Take our lid off here. Pour that right into our glass. We'll go ahead and garnish that with an orange wedge and a little flag there. There you go!

Please explain how to light a traditional log fire (in a fireplace)

tutorial you're gonna need some newspapers and kindling and some logs and I'm starting off by folding the newspaper into long thin strips and then tie them into sort of like butted balls and putting them into the great you're probably need about six or seven of these and by putting them into nuts it makes them more compact which then means they burn slower meaning that the fires are burning better it works trust me so as I said about six or seven of these until you're all done just keep folding next we're gonna add some kindling so about six or seven strips into this shape and because it lets the air through it and which makes it draw better up the chimney so I'm trying to light it very unsuccessfully some aliens and cut them all into the bottom of the grade and then lighting the cotton wool highly flammable guys be careful and but it makes it burn quicker it's very effortless when you do it like that so they've it a couple of minutes and you shouldn't need to leave it too long just until it starts burning the kindling as well as the newspaper and you sort of get a feel for it when it's just burning nicely and then you can think about adding some locks so any second now use tongs guys another safety precaution there add two or three logs round in a similar shape to where the kingpin is basically trying to transfer the heat over to the logs and so once you've done that make sure it's well seasoned logs not just something that you pick up at the woods you know it has to be dried out otherwise it won't burn well I'm leaving it for about ten minutes or so now you can sort of leave it to get itself burning nicely something a guard over the fire and again just to avoid any accidents you know just be careful it's an open flame you never know how long how long it's gonna be for there is an accident time back and and it's burning really nicely now I'm just gonna give it a quick poker poker and then add some more logs on just to keep it burning nicely it was all Bank itself down and then you can sort of build it back up again it works really nicely and so once you've done that you have a very successful fire burning and just add more logs as you need them guys just remember but to be careful okay that's basically it you know safety precautions treat it with respect is you know one of the basic elements fire and you need to use it sensibly really but that was the video I hope you enjoyed it hope it was very informative and I hope that you like comment subscribe all the rest of it below thanks guys see ya

Please explain how to propagate

hi everybody it's Gina and I'm back with just a quick video and today I'm going to be talking about my wondering gym commands now most people use these as potted plants or transfer hanging baskets but a few years ago I took a few cuttings and I simply just threw them on the ground and you're looking at what I now have and this is just one area of the yard where I have The Wandering Jew now this location has undergone quite a few transformations in the last couple of months Ilona I planted different vegetables in this area I've completely ripped out the wandering jew leaving just a few pieces for for them to come back and you'll see the the few transformation that that it's undergone right here I had some kohlrabi those have since been harvested and over the next couple of weeks Spanish needle began to grow in that area and once I was happy with all of the the harvesting that I had to do then that Spanish needle was removed but you can see just how far the wonder Jew has spread in just a short period of time now this wandering jew for some people it's a pest that you just can't seem to get rid of but I absolutely love this plant it is a lowest maintenance or I should say absolutely no maintenance whatsoever if you want you can just let it let it run now right now it's about I think 50 degrees outside and it is supposed to drop down to 39 degrees tonight so tomorrow morning some of this might not might be really really beaten up by the cold weather so I may end up having to pull a lot of it out and throwing it away but it just comes back it doesn't it doesn't kill it completely so you can see right here after I've harvested all up the Spanish needle and cleared that area out The Wandering Jew is it's just taken off with a vengeance I just love this plant it keeps going and keeps going and a lot of people you know really consider it a pass but I think it's just absolutely gorgeous plant this is my backyard where I took a couple pieces and just threw onto the ground and it's not wandering in between the ferns and if you have the bromeliads now this is one area that I do try to keep kind of neat but I kind of looked lovely unfinished look that it has back here so I just let it go it also has some purple heart that you're looking at right there and I'm going to be talking about those in another video but you know how you can't go wrong with a wonder in June and to me you just can't have enough so what happens when it creeps through the fence onto my neighbor's side of the fence I simply go back there and I clip off all of the pieces that are peeking through the fence and I either throw them away or I take them and I put them into a pot or I find another spot in the garden that I think might need a little bit of help and I throw them down there and within a couple of months I have a whole other batch so what I decided to do with these ones that I cut was just simply to pop them up some of them will put into some water for a later time but I went ahead and just bought a few pieces the most people would just use some tiny pieces and put in there but I kind of wanted to have a full pot from the get-go a nice nice full a nice nice full pot of the wandering two pieces so I tended to put in larger pieces and I put them a lot closer together and most people would probably just put one tiny piece and just a lovely to grow and fill in but I wanted a lush look from the get-go it is very easy to propagate this plant all you need are a few cuttings and you either put them into some soil in a pot or you put them into the ground all I did was simply throw a few pieces onto the ground I did not even dig a hole and put them in I just simply threw them down and within a few weeks I had a full area of wandering jew you can see just how lush this pot looks after just a few days of having these planted what you're looking at here in this area is just a couple cuttings that I threw on the ground again and they managed to just take off and within a few months I'm going to have a full area completely covered with Wandering Jew

Please explain how to make new crayons from old crayons

Hello, today on Wondermint Kids, I'm here with my friend, Flora, who is a great artist. Hi! And we are making a cute and fun project made out of recycled crayons. We learned it from Martha Stewart! All right, to get started you'll need a few old crayons, a muffin pan, and a parent or guardian to help you. Okay, if you really want to get started, take a lot of crayons and start peeling the wrappers off. Now you can break up your crayons into tiny pieces. If it's too hard using your fingers... ...ask an adult and they will cut it up with a knife. Now you're going to take a few crayons and put them in your muffin pan. And you can make any design you want and use any colors you want. Now, ask an adult to heat the oven to 150 degrees and then put your muffin pan into the oven. And voila! This is what they'll look like! To get this craft idea and more, visit our blog, wondermintkids.com. Bye! Wow! Wow, that's so cool! Looks like an eraser.

Please explain how to frost a cake with ganache - upside down method

welcome to Gayathri's Cook Spot I'm Gayathri Kumar and today I’ll show you how to frost a cake with ganache using upside-down method. This can be used for cake which needs to be covered with fondant. For more interesting recipes visit my blog gayathriscookspot.com Take a larger cake board and cover it with a parchment paper and attach it with cello tapes and four sides. On a corrugated board add ganache and place the cake the board has to be one fourth inch larger than the cake on all sides this is a layered cake so use any filling you want I’m using the same ganache which I’m going to use for frosting place the other on top and crumb coat the side. the crumb coating doesn't need to be very uniform now I add some ganache to the parchment paper and spread it out to a circle which is larger than the cake. there should be no space between paper and the ganache. now invert onto the cake top and using a leveller check whether the cake is properly level. Otherwise just press it until the air bubble is exactly in the center now carefully flip the whole cake and remove the larger base. again using the leveller check with a big cake is properly levelled. Check it out on all the sides. Once sure that the cake is level add more ganache to the sides filling up the whole area between cake and the board. The aim of this upside-down frosting is to get perpendicular edges and neat finished top. with the bench scraper remove the excess ganache now fill any pores on the sides of the cake and again remove the excessganache you need to repeat this until the sides are neatly frosted. once the sides are done it's time to flip the cake back remove the tape and the cake board leaving the paper on top. refrigerate for at least 30 minutes and its firm gently remove the paper You can see that the top is not very smooth so add some ganache and the fill in the pores keep some hot water ready Dip the spatula in hot water and wipe it clean towel and use the warm spatula to make this top smooth that's actually a very long process it takes nearly 15 to 30 minutes so be patient and smooth the top and the sides of the cake. once you have done with this set the cake aside for 4 to 5 hours until the ganache sets properly then you can cover it with fondant or modeling chocolate that is it. ganached the cake with upside-down method i hope you found this video helpful if you liked it give a thumbs up. my ebook is available on Amazon please check the link in the description box below and please subscribe to my channel to receive updates thank you

Please explain how to make cranberry granola bars | make your own energy bars

so today in a first for GMB and I myself actually we're in the kitchen where with Tim Morris of podium catering who looks after Afton racing at the World Cups does their breakfast lunch and dinner so knows how to fuel the top World Cup riders what we making Tim making cranberry granola bars today cool so something you can chuck in your pack for big long rides and all that excellent yeah just like that and super easy to make as well cool so you know what they say about too many cooks and that so just give us a call when they're ready Tim we just got started porridge oats all organic we've got the cranberries so it's the name we got unrefined brown sugar walnuts sunflower seeds flax seeds chia and sesame seeds first step then let's turn the oven on and switch it to 160 on this is a fan oven 140 if it wasn't fun oven so the second step is to we've got some coconut oil which we've melted down is about hundred grams in there and melt that in with set honey it's about three tablespoons we've got the dry ingredients over there that I showed you before and these are the wet ingredients that are gonna stick it all together so you've got here coconut oil which sets and also this is why you set honey a paste or any honey so this is just on a low gassy this will take a few minutes just to to melt down okay this is what this has been on for about a couple of minutes or so now and it's all melted down and and it's ready to chuck into the dry ingredients so now you've eaten a fair sized mixing bowl doesn't matter which order you put them in hundred gram of oats 100 gram of cranberries unrefined cane sugar chopped walnuts sunflower seeds sesame seeds cheer and flaxseed say chia seed that seems to be able to a buzz around those and they're in the food industry loads and loads of protein and that's a the guys I cook for they want a high protein diet say you chuck as much alive in as you can just for a bit of flavor chef gain a bit of cinnamon give them a bit of a stir and yes you've got all your dry ingredients in there you've got your sugar in there people obviously you know sugar gets a bad rap but mix it in with the Lapera Jade's helps bring the GI dang so it'll give you energy for a long time basically like Neal said chuck them in your pack or you're going right so we've got our oil it's still really hard to be careful not to splash this but basically I'm just going to pour this into the dry ingredients as you can see it's bubbling away and just give that a good old mix so that's all nicely mixed in all the no dry spots left I've pre lined a brownie pan just so they don't stick to the bottom and just tip it in I'm gonna press that in my hands spread it out nice and even so these are ready to go in the oven night like I said 160 degrees and they're going in for about 25 minutes or until they're golden brown right these have been in the oven for just over actually just over 30 minutes now and they're ready to come out Oh smells good in here Tim these are ready to eat yeah not quite Neal just got cool these down for about 20 minutes to say oh I'm just just indexing the gears right so that these cooling for probably the best part of an hour and now you want to make sure they're nice and down to room temperature so I'd chance for the honey in there to set and crystallize and hold everything together otherwise you just have a big crumbly mess these bars ready yet to get in there Neal patience so just chop these up into whatever size you want I find a nice generous piece like that it's good for the back pocket if you're out on the road II let me add it these you want to keep stored in I'd normally keep them in a some kind of Tupperware box and just keep them in a dry cupboard not the fridge the fridge you probably just get a bit soggy awesome cheers that Tim in for see more videos from GM been in the kitchen click up there I'll click down there for training playlist well click and me and my a Spinola bar to subscribe to channel

Please explain how to use a router

I'm Dominic commencement diy.com in this video I'm going to show you how to use a router for those that are scared of a router it's actually in my opinion one of the safest tools in the shop to use but doesn't mean you can't get your fingers ripped off by it anyway first of course on a router you want to pick the bit that you want to use in this case I have a nice colonial type one going to put a nice edge on a three-quarter inch piece of plywood once you have your bit installed into the router on it on an every router it's going to have adjustable base this particular one I just turn it you see it changes the depth of the cut now once you have what you think you like just look at it like right on the top top of it like like this and once you have what you think you would want I'll try it with a piece of scrap wood oh by the way tighten it down mm-hmm try it with a piece of scrap wood a couple times a couple different settings and see which one you like on most routers you have a indicator tell you what the setting is on so you can remember it for the one that you do like so let's get going cutting them or routing your say a piece of wood and show you how it's done and now of course working on any project specially smaller pieces of wood where they can start sliding across the bench or whatever work surface you have for the router I like using this pad and you can pick up a home depot or lowes or any tool supply it's a nice little rubber pad that you put under your wood and it really helps it from prevent it from slipping works pretty good I like to use it all the time I mean especially with the router because with the router if you make a little mistake chances are it's a big mistake another thing on the router you have the base alright now one very very extremely important thing of course with any tool go slow not in a rush right on the base once it makes contact with the wood huh you don't want it to slip on the router you can go back and forth I don't recommend it but sometimes you have to but what you don't want to do you don't want that base to lift off that would even the littlest bit because once you do that this blade the bit here it's going to pivot like that it's going to change it either make it cut less or usually will cut more make a nice gouge into the wood so you don't want to do that you want to make sure that base is down what I like to do you got the little handles here and people come use them like this yeah you can but I really don't I like recently I'll use one handle I like to put my hand on top of it and I put my hand my fingers down on the base holding it down that's the way I do it honestly I don't think I could do it this way I just feel too moving like this it's a little bit more sturdier then of course let's get going uhh I'm gonna go around and cut the corner and I'm explaining to as you just see me do it when you're going around the corner you're going along fine nice and straight nice and straight no problem we're gonna go around say a 90-degree turn now keep in mind the grain of the wood no matter what kind of wood you're cutting has it changed drastically you want from a rip to a crosscut and the blade depending on how sharp it is or out Dola does it say it's going to act really different they've owned this way nice nice nice you go around the bend and Wow and all sudden you feel big difference and the router codes you know do these things on you do some really weird things where on one side you're just about pushing the router now over here you're going to be pulling it it's gonna feel quite different but always remember again don't let that base come off you don't want to do any of that that's pretty bad but when you're coming around that you're nobody says that you have to do it on one shot you can do a little piece out of time that's the whole good thing about having a bit with it um one of these bits with a bearing on it because you're not gonna you're not gonna go any further than what you have this set at and there's bearing which rides on the edge of the wood is going to allow you to do it so go ahead and do this and uh pay attention and you'll see what happens all right well we're all done got my little piece of wood you can see got a nice clean edge on it of course you know you're cleaning up a little bit sand it down some fine sandpaper how much without you can really see yeah yeah you can see that anyway I'm Dominic from XP DIY calm thanks for watching

Please explain how to make cricket bats: old traditions & modern methods (1962) | british pathé

from these tiny seedlings will grow graceful willows not planted simply to please the eye but for a specific purpose for this is Suffolk a sensor of the cricket bat industry here in lovely green meadows alongside running streams willows grow in their thousands and in this nursery young saplings are carefully brought to maturity when the tree is about ten to twelve years old it's in the ideal state for making bats having been checked that it's the right size trunk must be ten feet long the experts arrive to bring it down this tree should provide two dozen blades which is about the average one giant in Essex standing over a hundred feet made more than 1,100 you the manufacturer of the cricket bat is a curious blend of old traditions and modern methods to be expected perhaps in a trade 200 years old for instance the splitting of the wood here is always done by hand never by machine then the blades will be graded as just another stage in a long process before the wood block becomes the familiar bat the willow blade is naturally tough but it must be made harder this machine does the job with a 600-pound pressure when the blade has been shaped it is ready for the splicing of the handle this is made of sarawak cane into which layers of rubber a place to give extra power the splice will be so neatly fitted that even left unglued a match could be played without the handle coming up there are strict rules about the size of the bat due to the easygoing regulations in the games early days when betting was common side stakes of a thousand pounds were common with those sort of sums in the balance some unsporting gents would open the innings with a bat so wide it would completely hide the stops the final touches cannot be given by machine a craftsman strained eye and instinctive feel for the right shape and balance does the job of shaping the bat swiftly and well you the cricket bat is almost finished twine binds the handle to give it the traditional grip 12 years of passed since the tree was planted from which this bat was fashioned a dozen years of care and skill giving the ideal product a cricket bat shape for surroundings like this

Please explain how to make your own raffle tickets (part 2)

In this video series I will show you how you can make professional tickets in just a few minutes right from your home computer. You can download a free demo version from our website and see how easy it is for yourself. This video will demonstrate how to use raffle ticket software to make professional-quality custom tickets in just a few minutes. First we'll go over how to create the body the ticket then the stub, and finally how to set up the ticket numbers. Keep in mind that this is only one style ticket. There are many design choices you can make that do not have to exactly be like the one I will demonstrate. That is the beauty of this program. You can download a free demo version of the raffle ticket software and try it out risk-free right now. If you like it you can purchase the program from our website raffleticketsoftware.com or call us at 1-800-944-9526. After purchase we'll send you registration information so you can start making tickets right away or you can order the program on CD and we'll send that out to you within just a couple of days. We've broken the videos down into the three main part to the program. The ticket body, the ticket stub, and the numbering specification.

Please explain how to rub under chicken skin

I like to start by going at the bottom of the chicken because it seems a little bit loose there it's a little invasive don't worry get your fingers up through the skin and the meat and just start working them around we're not putting any seasonings in here you're just trying to work your way in and loosen up some pocket pockets for flavor later sometimes the sides can be stubborn but just reach around you'll finally get your way in that sounds dirty once you get in make sure you also get down to the legs a little bit because return push and flavor down into there once again it's kind of easy just to move your fingers around and kind of work it loose and it in just comes apart and start from the top the breast and work the way down from there try loosen up the skin just imagine you're a year old and at the beach that loose skin now that's pretty gross I'm sorry sorry for the visual now let's give some of our mixture you can use anything it could be a compound butter but today I'm using a sun-dried tomato pesto and just push it as far as you can don't worry we'll work it down in a minute you'll feel like you're making a mess here and not being very productive but it is go in and just massage it down like that kind of get it up under the skin then you can push it down from the outside work it down as far as you can again on the other side and just kind of squish it on down there don't worry you're not going to do plastic surgery you kind of look like that woman is at 37 plastic surgeries it doesn't have to look pretty at this point trust me it'll look pretty when it's done let's get down to the sides and try to work some in there get it down to the legs like that just try to get to the top of the leg from the inside then you can come from the outside and just work it on down Natasha's a little bit yes none of the exact science just kind of get in there and work it around squishes thumb yeah your chickens start look kind of happy and now the double glove technique works really good you've gotten your chicken all good but you need to put some rub on it and your hands are all achy and full of e.coli bacteria well pull off the first layer being very careful not to touch this second layer that sounds like stripper music does not that's the what's a tunnel I didn't plan it that way so the other gloves away if you apply through both of them away not just one but sometimes you don't realize you dropped one of them whoops now come with your rub today I'm just using a bill and Cheryl Jamison perfect poultry rub great rub is from their book - smoking spice always mix up a lot of it and keep it in an extra spice drawer like this and just literally sprinkle it on it's great color and flavor chicken a little bit of a fresh cracked pepper now we can get back to the business of getting the outside done just kind of imagine you're giving some co-ed and I the suntan lotion massage the excuse me sir could you please rub this in for me yeah well that's what you're doing to this chicken working end up under the arms there up under the creases under the legs yeah you don't want to miss any spot let's get it all in there yeah it's chicken cooking good now tuck the skin down if it come up a little bit since you've been pulling on it and this birds pretty much ready for the grill now

Please explain how to make twinkies video how to make twinkie recipes

you've probably heard the urban legends that Twinkies aren't made from actual food so you know they've got a shelf life of like forever it's not true this is real sponge cake this is real cream filling or I wouldn't want to do this oh yeah because it's real food we can make an amazing home clone so I'm gonna go over here to the store get some ingredients meet you back in the lab oh and if you want to see what a Twinkie does look like it's been sitting on a shelf for over 10 years hang in there tom top secret recipe top secret recipes top secret recipes Todd Wilber for $26 you could go to William Sonoma and get this here Twinkie pan which is crazy because for that same amount of money you could get this many Twinkies a hundred Twinkies you don't need to buy this pan I'm going to show you how to make the Twinkie pans from scratch it's super easy we'll love put this on eBay because I'm heavy-duty foil rip off the square piece fold it in half lengthwise fold it in half again good self Spice bottle Spice Islands is great cut a round bottom on it makes it look more like a Twinkie hold it up like this fold in the ends take out the bottle I get tight here on the ends put this in a pan we're going to use this pancake mix this is our cake mix but we're not going to pay attention to the instructions on the back instead we're going to do this four egg whites beaten until kind of stiff like this okay then take this pound cake mix up it into a bowl a little bit of water mix that up so we have our cake mix looking like this we're gonna get our egg whites fold them in spray these suckers so we can get our creamy keys out later a little nonstick spray in there golden and then load in some Twinkie betta felt about that much in each one okay get this marshmallow cream 2 cups a little bit of shortening some powdered sugar and just a touch of vanilla look at that perfect right its Twinkie filling here's our real Twinkie and if you look on the bottom there's three holes that's where the filling goes so we're going to do that in our clone same thing grab your clone out of the foil get a chopstick and start making the cavity inside your Twinkie this is where the filling is going to go now what your filling in a pastry bag I've got this gun right here okay that's how we're gonna load it start loading fill it up fill it up fill it up ready Twinkie cream filling and into mouth mmm who's actually still warm that makes it way better oh that's so good clone Twinkie now let's find out what the old ones look like I've been waiting for this see that see that right there that's when I bought these Twinkies let's see what they look like thirteen year old Twinkies no mold no no weirdness they still look like a Twinkie isn't it crazy except for one thing they're hard okay like petrified look it like it they're hard like a rock can smell funny too smell that yeah hahaha man sit look at this okay now let's let's open it oh my God look the filling the filling is completely hard inside Twinkies do not last forever I have an idea let's take these outside maybe outside and petrified I think I just got petrified Twinkie in my eye

Please explain how to cut back perennials in the fall

hey folks there seems to be some confusion about whether perennials should be pruned back in the fall or left until the following spring both answers can be found online but here's my take on it if you want to feed a few Birds then the naturalist garden advice is correct leave the flower such as these echinacea comb flowers alone and the birds will eat almost every seed I mean we expect a horde of barbarians Avenues chickadees to violently attack these cone flowers in a little while if you want the garden to be cleaned up the looking neat and tidy and perhaps you don't want any more seedlings then you cut off the spent flowers and cut the ground to the plant to the ground in the late fall and I'm going to be doing that with these black-eyed Susans for sure because they'll take over an unsuspecting gardener is there a right answer it doesn't matter to the plants nobody's printing them out they're in their natural state so they'll do quite well either way the answer is up to you and how you want to approach your garden one at meat room before snowfall one at wild leave it alone there's no one-size-fits-all here contrary to those who take positions on either side of this design maintenance fence whatever works for you is what's right for your garden I'm Doug Green and if you fog that garden thought useful I hope you'll subscribe to my channel to have them delivered right to your inbox

Please explain how to make a diaper cake centerpiece

hi today I'm going to show you a really adorable quick easy centerpiece for a baby shower and you can always give it to the guest of honor at the end so it is a gift also it's a small little diaper cake it's really cute so what you need is I'm using a 20 pack of newborn diapers but you can use size 1 I just think newborns they're just a little and cute ahh some string to tie the diapers together something to decorate it I'm gonna use yellow ribbon and a yellow flower for the top I think it's just really pretty against the white I'm also use a glass cake pan to put it in so it's in the center of the table really pretty you probably should use a rubber band just makes your life easier and I also have white crinkle paper that I'm gonna put on the bottom gonna be really pretty so you can use get better jar or soup can whatever it is and you stick your rubber band around it you take your diapers some people roll their diapers like this and then they tie them and then they stick them in that's not what I'm going to show I'll show that in another video but for now we're going to do it I really like the look of this one this just kind of has a classy look to it so we're kind of putting the diaper on top of each other kind of like a scalloped way so we're going to stick those in here and we're going to work our way around it so you just start your rubber band and you just take your diapers and you just go all the way around you just keep going look at nice and pretty sure your diapers are facing the same way as you go around just keep going around all I'm doing is I'm grabbing the diaper and I'm putting it in there scalloping it like this so it's kind of like step and you just keep keep going around and round around when you've gone all the way around you can take your soup can or peanut better jar or whatever it is it's in the middle hole no mutt just take a couple of diapers together and just kind of roll them in a ball and step in the middle so now you have a beautiful outer layer and I just take the rest and I go on the inside so now I have that circle of diapers on the inside and I'm just going to keep going around it's kind of making it a little bit bigger it's getting them in the middle because we already did the outside are you looking really good so just keep going with get up in the middle what's very very pretty I love how a yellow and white look together okay so I'm gonna kind of try to make all these little folds around outside even because it just looks cleaner neater prettier all right mess with it after I have this string on then I'm gonna take your string you can actually just leave the rubber band on if you want I don't like to because I reuse my ray-bans so I'm going to take the string tied around it double knot it and then you can take that rubber band right off like that then don't really want string left on my diaper cake go put it on you're going to take your pretty ribbon and go right along that line sometimes I do get my hot glue gun and because I want it to look flat and I will just cut here and glue this on here just so it's flat and then you can put something over it like a flower but this one I really want to do a foe so I'm going to make it longer for bow okay mm-hmm tie a bow just do not that don't not it yep you're not very good at those like I am not very good at those what you can do little trick I learned is you take the two pieces like this and you Tommy on like that it usually comes out very very pretty and look a little trick I like to do is i hot glue gun this here and this here so that it looks like the perfect bow it actually works quite well otherwise you can just tie it with a regular bow just like you would tie it bow which doesn't always come out as pretty so either way you have that take cake pan now that your diaper cake is in shape and I like put a bunch prinkle River just around the edges I just like to kind of put it on there and move it all around make it look great keep messing with it until it's kind of spread out and you can always add more or less whatever you like I like a little more on the edges just because I think it looks better that in the middle stick your flower on it and what I like I like the bow in the back I like it to look very flat in the front so I'm going to leave it like that and it's just the cutest little centerpiece because you can just put it on like this or you can even put the top on it which is really really cute too so the end of party hands on the diaper cake and it's a gift too

Please explain how to make a puppet nose! - puppet building 101

welcome back and today we're gonna learn how to make a puppet nose make sure you download the free pattern I added to the website step one is to cut out the pattern pieces now let's get to work now to make a nose like this you're gonna need a half inch wide piece of foam take that foam and lay it out and make sure you have your foam nose pattern don't get it confused with the fabric one and then just gently trace it out carefully cut it and use a razor blade for this but on short cuts like this I like to use scissors alright so we have that all cut out now I'm going to glue it together so that while it's drying I'll cut out the fabric nose to glue this together I'm going to use a contact cement you can use hot glue but the context cement is much easier when using the context event you have to be in a well-ventilated area you should really use a respirator too I have the door open two windows open and a fan going so I have a lot of cross-breeze a lot of people use barge but this is something that I can get locally it's called masters it's pretty much the same thing some people have a technique where they use a little piece of foam or a little sponge to tack it on I personally never found success with it and use whatever technique that you wish be careful not to get on your hands too really it's good for your skin and hot glue would work with this also this is the actual glue that I use to put all my puppets together I only use hot glue for this video series because I think it's a more accessible material to most people so there we are I'll put that to the side to dry now for the fabric nose again this is an Antron fleece but if you look at the Antron kind of like how fur has a direction so does any other fabric you can tell by pulling on it you can tell this way it stretches a lot and this way it doesn't stretch near as much the side that has the stretch you want to put the pattern that way so I'll carefully trace it and then I'll cut it out there it is now just to make sure I don't forget which side is the bottom put a little mark there now this glue is getting pretty tacky I think we should stick it together the key is to really make sure you get it pressed in evenly so if you can see it definitely doesn't look perfect it's a little bit lopsided and a little angular but I have the perfect way to fix that I use a little stuffing so you just cut a little hole with the razor blade make sure you're careful they take some filler and stuff it may actually stuff it kind of tightly it helps push it out now you might be thinking why didn't I just put this in before I closed up the seams and I've done it that way before too and I don't know why I just don't seem to find the same success you could try it though if it works for you let me know those close up that seam and then boom much better let's get a closer look at the sewing for our puppet nose here's a piece flat now when I'm sewing this I like to start a little bit higher up about right I'll put a little notch there maybe an inch up from this corner okay right there so what I'm gonna do so what I'm gonna do is attach it here right on that knotch line these up evenly I recommend you use pins I had a couple people commenting asking what kind of stitch that I do and the puppets and I actually just do a whip stitch if you want more detail on the whip stitch just look it up on YouTube I'm sure there's a ton of videos on it but basically this is it you're just going in one side and out the other some people do a ladder stitch I don't recommend that for this a ladder stitch is meant for closing up the final seam on an entire piece it's really not made for construction so here's where we are we have those two edges sewn together and we have this bottom flap now what I'm gonna do is match up this bottom flap here with the corner of that and okay so now we have two of those edges sewn so there's one more seamless so I'm gonna start it so it about halfway and then I'll put the nose in all right so I still have about two inches left here too so you can see the coroners right there and I still have to go around that edge but I still have the thread needle hanging on there so it's all one continuous piece to make sure that you matched up the right way having the back toward the back for both of them and I'm just gonna turn this inside out force it in try to line up those seams and now the rest of the seam I'm just going to whip stitch from the outside now you're having a perfect little puppet nose for now I'm just gonna hit it on but you would want to stitch it on so let's see here look at that nose looks great on them doesn't it so everyone commenting I do have plans to make an eyebrow mech video I have a couple other videos planned first so don't worry just hold tight that mech will come later in the summer see you soon

Please explain how to make a origami frog mouth

ok so what my sister is making origami and i'ma hold the camera for and I'm making videos too but ok ok well we're gonna use um ok for whatever paper she's too shy to show her face you're gonna do this it's called folding in half yeah like a hamper video that's a hot dog like that make sure to put it right she's not really perfect but gotta make it at least as a neat as possible ok then you're going to make it like airplane at that half but it's gonna be a boat pretty much like a boat yes doesn't always got to be precise hey like that hopefully I can see this see yeah your make you pretty much making a boat yeah you make a boat but from there you open it then y'all can see his big lever on the side oh whoa place you gotta put the corners inside yes yeah just stuffed in the corners you're printing background music in my tablets she wants background or selling to go with music is as a favorite say yes I think it's your favorite and then ya do ya do this yeah open it okay this is the front open it from the side put her in here like a diamond to looks like a diamond then as you can see you got corners I cut open wait you will do this so come put this just climb up luck also the also this one block them up to the top 100 be kind of confusing then you open it again close it like a diamond hold it in half and then this year um no head splits and there's your mouth wait deca prob um look at the look at the flex where you can put your fingers in so the flaps there yeah show me your pity person yeah you just open and close them and it makes like a puppet hold the frogs and you want to end it and that's how you do and bye

Please explain how to make rutabaga fries | healthy low calorie alternative to french fries and sweet potato fries

hey guys a couple of weeks ago my buddy introduced me to rutabaga fries if you don't know what a rutabaga is it might be called a turnip a Swedish turnip or an EEP in your country at least that's what commedia tells me it's basically a starchy and of vegetable sort of like a potato but it has half the calories of a sweet potato so you can eat twice as many rutabaga fries as you can sweet potato fries for the same amount of macros a dieters dream come true that's what we're gonna be making today now let's get cooking all right so why do I love you so much the macros every medium-sized rutabaga which is about 386 grams is only 145 calories half a gram of fat 33 grams of carbs 9 of which is fiber and four and a half grams of protein if you compare that to the same size sweet potato sweet potatoes about 350 calories and almost 80 grams of carbs so I highly recommend adding these in your dieting arsenal you will not be disappointed question of the day I'm doing a 10,000 subscriber Q&A video any day now and I'd love to answer any of your last-minute questions in the comments below so be sure to get those in if you want to put the recipe out you can do so by clicking the link in the video description below and as always thanks for watching guys

Please explain how to perform a compression test with a scope (picoscope)

okay i'm gonna i'm gonna shoot a relative compression test on a different type of scope i'm gonna do it on my picoscope this time uh this is the new 4000 series uh very nice scope i'll show you a couple connections and then we'll go to my smart board and i'll show you the rest of it all right for starter compression or for uh relative compression starter current i'm going to connect an amp probe in this case i'm using my uh my pico's high amp probe and uh this is a 600 amp clamp it is polarity sensitive there's a little arrow indicates direction of conventional theory current flow and i'm clipping that on my battery cable that goes to my starter so that's going to measure starter current and then the second thing i have connected is i have a sync probe connected to my number six plug wire see if i can show you that here my number six plug wire um i have a just a little rpm pickup type probe that um connected to my number six plug wire this is a conventional system so this guy is going to give me an impulse every time the number six cylinder fires i'm going to get an impulse from that and that's going to coordinate my amperage waveforms from the starter it's going to coordinate my cylinder firings coordinate my compression from each cylinder i'll be able to tell which cylinders which okay i'm doing a relative compression test with a picoscope i'm gonna click on my pico6 icon on my desktop this is a laptop based scope and i'll walk you through the settings with this channel a that's where my amp clamp is set i'm going to set this to my 600 amp current clamp and this is a nice feature because uh the scales will be set up for me i don't have to do any math or conversions so um 0 to 600 amp is the is the screen actually goes minus 100 to 600 amp so any negative amperage i'll see it and then the second channel i have my sync probe connected uh one of the things i do generally before i set this one is i'll adjust the scales with the car running so i'm gonna start the car real quick and and we'll set that one up so my second channel is set to a plug wire so i want to turn this on it's going to be voltage let's see what it looks like and uh there's a line going across the screen that looks pretty good let's up the time base here see a little bit more of it and that looks great the only thing is that red line going off the screen again this is a sync probe so each of these high red lines would be a would be the plug firing on that particular cylinder which we're connected to number six that's important to remember but i like to set it up with the car running because then i can get my my sync probe coordinated properly and be happy with the settings on that now we're ready to do the compression test all right for this one this is another nice feature of the pico what i'm going to do um is i'm going to set up a trigger and i'm going to do a single shot and i'm going to set this trigger on channel a and i'm going to put it about 200 amps and uh what that's going to do is um it's not going to draw the picture and we'll take this up to a 500 millisecond per division screen we can zoom on this later but what this trigger is going to do right here is notice the scope's kind of waiting for it to cross that line so this blue trace i'm triggered off the blue channel it's not going to start drawing the picture until it hits 250 amps it being on a single shot what that's going to do is that is going to freeze the picture for me i'm over there at the car cranking i'm not over here to stop it it'll stop it automatically very nice feature of the pico and uh i'm going to crank the car i'm going to give it a a clear flood crank because i need the ignition system to be active i'm not going to disable the ignition pedal to the floor notice the picture's frozen single shot you see the this little icon down here at the bottom turned red so it stopped it and a nice feature with this tool is with a frozen picture i can zoom i can actually filter it frozen too which is cool uh if we take this amp pattern which has some hash to it we can actually throw a filter in on that you can see a lot more clear those uh relative compression humps if you want to call it so very nice looking picture another thing that's really nice is we can zoom on any part of this we want to and i'm just going to grab just a section of it and what we're looking at is our synchronized relative compression waveform and if you remember we connected this second channel right here uh we connected this to our number six cylinder so what we need to do now is we need to figure out firing order for this car this is my number six this red line and this is the number six again and we got to figure out the cylinders in between so let's uh let's look that up real quick all right so we look this up on mitchell vin 3 3.0 firing order on a v6 as you can see is one two three four five six so very easy one so then we go back to our go back to our scope plug in our numbers if this is number six our firing order is one two three four five six that's pretty easy isn't it so the next one here this is six this is one two three four five and then six again relative compression synchronized using a low amp probe and a sink probe on a plug wire so next thing i want to do is i want to take a spark plug out and uh we'll take a look at what that looks like with the plug removed all right what i've done i have um removed one spark plug and uh we're gonna retake this capture i'm gonna hit the space bar and uh it's ready to go again see a little green light down here is lit and my trigger single shot once again i'm gonna go clear flood mode crank i have one spark plug removed simulating a dead cylinder i really like that filter that makes it really nice and clear doesn't it uh ignore the other little red spikes they're nothing uh one of the things about doing this kind of testing is know what to look at know what not to look at we're worried about the big red spikes because that's the one connected to the number six cylinder and uh you know we can zoom back in we can stay out doesn't really matter i guess i'll zoom in on it again and we'll just zoom in on a little bit of this and what we're looking at is again this is number six i know that's the number six so i know this blue trace and that hump right there is the number six right because that's the one i'm synchronized to and the spark's gonna occur at top dead center and from there firing order so this is number six and we said that our firing order is one two three four five six so there's gonna be one two is missing three four five and six again so where's my dead hole number two cylinder has no compression and that is the spark plug that i removed is the number two spark plug first one on the front back two four six on the front cylinder head number two solder no compression synchronizing it using secondary ignition in this case what's different about the last one the last one was a waste spark and we had to worry about the high low high low compression exhaust where this one's conventional ignition and on the number six it's just gonna fire it's gonna be a high spike every time six on compression six on compression so all the way across the screen this is the number six cylinder on compression zoomed out starter current synchronized with an ignition firing and uh check out how high the amperage is on the on the starter on initial crack right this one's over 600 amps guys that is normal and this all has to do with counter electromotive force dc electric motors but uh that's uh a much nicer relative compression waveform clearer than uh than i got on the varus for sure so that's it relative compression with the picot

Please explain how to make ice cream in a bag

hi I'm Vivian with four complete calm and today we're gonna show you this really great trick it's how to make ice cream in a bag at home and what we're gonna need for this recipe is two cups of heavy cream 2 cups of half-and-half a half a cup of white sugar two teaspoons of vanilla extract and some kosher salt about I'd say about three tablespoons and then we're gonna have a gallon sized bag of crushed ice and also a smaller bag now the first thing you want to do is take your crushed ice and you're gonna add some salt to your ice zip your bag now this lowers the freezing point after you do that you're gonna take all of your ingredients which is our heavy cream white sugar we're gonna whisk all the ingredients together until your sugar is all dissolved so once you have all your ingredients incorporated you're gonna take your smaller bag and we're just gonna ladle or spoon some of this into the bag gonna close the bag we're gonna take our bag and put it into our ice bag we're gonna close this now this is really fun for you to do with your kids because you have to shake this for 10 minutes so you can just let them do it you might want to get some winter gloves so you don't freeze your hands off or you can use a towel and we're just gonna shake it so once you're done shaking your ice cream you're just gonna pour it out and serve it now just to let you know this recipe it is not a super firm ice cream it's more like a soft-serve but it's absolutely delicious and your kids will have a lot of fun doing it get on it ten minutes who's gonna take this double-bag you're putting the shake weight where you can make ice cream in trouble

Please explain how to make stromboli!!

let's make a stromboli today what you'll need is some mozzarella cheese a ball of pizza dough you can make your own and I actually have a recipe that i will link but i bought this obviously at the store and you know this is like the best time saver there is so pizza dough toppings of your choice but what I'm putting in mine is a lot of fresh chopped garlic because we love that some onions some canned mushrooms because I don't have any fresh some black olives green olives some turkey pepperoni and some turkey sausage crumbles now pre-heat your oven to 350 and while you are preheating your oven roll your dough out to rectangular shape and I'm going to do that and we come back we will go to the next step okay because pizza dough is so elastic this is not a rectangle shape but we're going to work with it so at this point you just fill it with whatever toppings that you want and like I said I'm going to put all the toppings that I showed you earlier but what I forgot to tell you is I'm going to put a little crushed red pepper flakes and some Italian seasoning on it on the very top of it so when I get finished filling it i will show you how we roll it okay you see how many or how much my toppings or how many toppings i have on it i can't speak it's sunday so now i'm just going to put some Italian seasoning over the top and a little bit of crushed red pepper flakes just remember do whatever you want in the middle you can look like put buffalo chicken filling in here with some sharp cheddar cheese you can do whatever you can even do a breakfast Stromboli so now that everything's nice and piled on top I did spray my pan that you can also use the nonstick aluminum foil and you just start rolling rolling as your hand moves put a towel under it and it won't move by the way now when you get a little bit of it rolled fold the sides in like this and like that like I said the dough is so elastic it's ridiculous i'm going to push this pan up so that it won't move that much on me and you just grow it if you have long nails watch that you don't puncture your dough now when you get to this point right here take this side of your dough and just stretch it over to the top stretch it and stretch it stretch it some more until you kind of tuck everything in see how what I did we're going to fix the stromboli role here now at this point you can do an egg wash on it I did it the last time I made this drum boli I actually tried this recipe before I made the video I don't know about a week or so ago and I did put an egg wash on the top but then what you want to do now let's make little tiny slits on the top you don't want to go too far in just little like that like that that was a little bit too far but that's okay now what you can do now like I said you can do the egg wash on top or not you can put some Parmesan cheese on the top or not I'm just going to sprinkle a little bit more Italian seasoning now at this point just stick it in your oven 350 degrees for about 30 minutes or until it's golden brown and you'll see that it's risen when we come back okay it is done now you notice that I did not put any pizza sauce in there the reason I left it out is because look do you see if Owen who anyway sorry food porn is because if you put pizza sauce in there you know it could the crust inside the dough would become kind of soggy so I mean it's just personal preference if you want to put pizza sauce in there you can but look at that loveliness oh yeah mm-hmm so there you have it um I hope you try this let me know if you do and until next time love you guys you

Please explain how to make an angle inclinometer.

I'll show you how to make an inclinometer Cut out the scale from the template. Poke a hole at the cross and slip a string through it. I glued the scale to card stock to make it stiffer. Tie a washer to the string so it can hang below the scale. Tape the scale to the bottom of a cardboard tube. Decide which end of the tube will be the far end. Cut four slits at the far end of the tube: at the top, bottom, left and right. Slip thread through the slits and tape it. Look through the tube at the object you want to measure. Pinch the string against the scale... ...and read the angle.

Please explain how to - crazy full metal flake rangerover - mirror glass finish - epic paint

okay good evening yes I know I'm sweating and I'm hot it's been one of those days but uh we're gonna do some more flake I hope you enjoyed the coffee machine one that we did this was get rid of it more out there a little more crazy regarding the flake I suppose have you ever seen a chrome plate Range Rover me neither with a black plate roof okay so got my there paint two on I think I need a slightly bigger one to deal with this one's a bit small and that's like wearing curbs oh right it's let's get to it I've spared you all the boring stuff the Ranger was already in there I've already primed it had to do loads of repair work to the body kick this on there Liam did all the repair work sanded it down got to the 240 grit we then smashed er two coats last night actually two coats the courts I build primer but we've reduced it by 30% and then we 400 it grip followed by 600 today so it's all cleaned off it's all private art it's all ready to rock and roll we've masked up just the roof and that's time to get going okay so because we are playing we've passed everything else is super time go ahead two coats of base let it dry and then we'll be on the fake I don't know if you guys got a lot of that I apologize if you didn't I thought you'd have an ideal place to rest but it was not meant to be right we're going to let that bass drive fully now I keep forgetting because I'm going to mouth making a lot of candy sister I'm using my mt-10 bullet quite a lot and it's nice to go back to the standard with a team sorry the TE 10 on the base coat and this has got the TE 20 and stuff like that let it out get it done this is brilliant I really forget how good these because I've got so many I forget how good my guns are and I go back on all [ __ ] nails blue you have that right it's on the roof we left the black base down like I said we're going to learn fully fully dry now so what I mean we'll give about half an hour 40 minutes in the meantime we've got to get our flake ready now like I said it's going black flake we want maximum coverage maximum pot so what do you do well you 50/50 you point eight you're 15 which is exactly what we're going to do so there's our eight and as our 15 I know roughly what the guns take what the binder will hold so I'm going to mix enough for two liters and then if I need any more I can just mix it so right let's see if we can get you somewhere better oh that's better okay oh man I wish can't see oh no doesn't Betty shove it this is the most amazing stuff ever I'll show you home see sir linear there we go there's a flashback that's point 8 and 15 mixed together and you can see you're going to get massive amounts of pop and you're going to get crazy coverage which is exactly what we want okay you beautiful beautiful people it's time to get all this mixed up I can't find my turn up huh boom fast basecoat thinness so that's now mixed 2 2 1 I'm ready to proceed flake and we go okay dancers so you could go another or if you could go ten or twenty grounds in that definitely but you can just see you use the point a and you get tone you use the 15 you get pop I think that's the best way to describe it okay it's time to flake now remember no filters and only go 3/4 so you have enough room to shake but not like your [ __ ] I know God let's shut up your ass so really mix it thoroughly mix it that's the last Co hope you can see I know lights quite bad ah my stuff done now one day oh god I get this puppy I think you do a roof but still have like will quite close how the overlaps bar now let this go trifle it for an hour and then we smother a thing clear okay we are done with the flake and you saw pretty much it went down perfect we've got excellent coverage it was just where it needed to be any reduction on this whatsoever going to get in there look at this five meters yeah okay perfectly even there we got Range Rover Burke not play glass okay there we go four coats of our micro flake on this range of we gotta clear yeah obviously you're gonna let it dry so we're going to go to it with our liquid class Claire come there we are one bullet my kids burners come on let's get out of here now the last cut three beautiful coats of liquid glass ready to become muffins we're not gonna get a mirror finish is right that's it's not gonna happen ikura not to go now it's just us one life god she's got color sanding button mouse go through this Ranger of a roof looks pretty [ __ ] special the buff finished up muscle the up blank on there think they are as well there's covers for these call it in getting ready to lay down liquid glass stock back together there you go what we do don't bring out all my [ __ ] words that's insane darling [ __ ] diamonds so thought that one in front I need decent camera slammed if you guys see this you good oh my okay yeah you can pick this up on her oh my lord [ __ ] back without boy type it aside Oh Oh oh my word actually looks [ __ ] incredible I'm not even girly but no it's not that's nice I did give you that oh my Oh you

Please explain how to make pom-pom animals/insects

hey everybody um I am going to do as you can see youtube video and I'm going to teach you how to make a plea where is it oh yeah a ring let's see I'm going to try and let my camera focus all right you can probably see that um see I did this design I'll tell you how and so it's a ring i guess and i will also teach you how to make like things like this the glitter glue is optional right now I don't have an inkling blue with me so I can't teach you how to put the glitter go on I think you can do that by yourself just scored it on the bottle feeding um I'm going to today I'm going to teach you how to make bumblebees jellyfish also this is the jellyfish but I used yarn today I'm going to use yarn you can use pipe cleaners to if you have pipe cleaners right now I don't have that clear some new Jean um a butterfly and a caterpillar um can stick them on I'll explain later so here is what you need it this is what you need I'm a glue gun you might need parental assistance with this it just depends on who your parents are um unless you're an adult and you won't need parental assistance I usually I trust it with it um glue gun sticks glow sticks to go into the glue gun as you can see um and I have my it comes with cord so you can plug it into the wall and so yeah you need you can get these at Michael's um hobby lobby um alle tot sorry um but what I'm saying right now who does tickle me you want to get the this for you it's mini glue sticks mini bitoni is big hole ye I don't know if I'm pronouncing that right that's in Spanish but it's mini glue sticks but if you have a big glue gun then you need large blue sticks I haven't anyone so mini Glo sticks it's just have to brand on here no um I thought this idolatry yeah you can get them at Michael's dollar tree or hobby lobby but there's 28 each packet at dollar tree um you're going to need me zoom in closer and then you're going to need puffballs pom-poms most of them fell on my bad um scissors i'm using my regular ones throne of your choice you probably don't need this let's yarn but i just was incest amay ting sorry I'm a little bit tongue tie today you're going to need googly eyes um any size you really want i think i'm going to use the small ones let me just flip these over yeah i think i'm going to use this these two small ones you know i might need to get more while I'm doing the crafts oh by the way this is a craft yeah um let's see I'm gonna dump this out watch one you want you know the milk caps that you have to tear off when you drink it's a new bottle of milk just flip it off and you can use it as a ring that's how I got my ring see I just I like to put it on this way see now I can use it as a little ring I actually made a video um with my little guy if you want me to upload it to YouTube um then I I will I will because i have a video with him so and his adventures so yeah you just pop it off the milk um or you can make these little things to sit down you can play with them and stuff like that I'm just too just for show you know um then you can use bottle caps doesn't matter what kinda bottle cap I would recommend to san e if you add pronouncing that right I don't really know huh um anyway um to sandia i would recommend that because it has the green stuff and it works perfectly with this Oh wrong one verbos with this and so I'm going to put that down and as you can see my my little character has ears on a tad um that's why I have little strappings of acorns I'm not really going to use anyone because I don't have a cap and Plato right now but I could just cut off my pins tops now I won't know I just have put there because i just wanted to show you that you can use a corn scrapping to put a little hat on them or just if you have acorns on your area you know um yeah I'm just gonna put this back in game alright and so those are the stuff that you need and yeah I was what you need um you're wondering what these things are I just thought I might be a little bit festive cuz I'm making each video in here so um let's start off with my bein here um craft that's what's called sorry where's my mind today um just then this is going to be kind of hard um it gave me a second to prop this up all right um well give me up you can only see my legs and stuff right here so what I'm going to say right now is let's begin now i am going to teach you right now i guess in this video I'm going to teach you how to make a butterfly see and a jellyfish um and the jellyfish can go on ring or a where are you or a cap alright um oops so what we're going to do right now for let's see d okay let me fix this okay alright so what we're going to do for the butterfly I'm gonna here till it is to pom-poms and they're both good this is going to be the body and I'm gonna stick them together the body um and then for the wings i guess i'm going to use drumroll purple and blue so it's gonna be like gonna be like hold on it's gonna be like this and then the body in the middle so it's gonna be kind of unique if it goes and so there we go so in all you're going to need one two three four five six six pom-poms whoo um see small googly eyes so right now I only have one solo see I only have one all right now let me go get the other small one back and my comer is right wait we just measure my eyeballs yes they are perfect now ooh and I guess what I can I also found a clip whoo that is cool um but I might add that later after this video to one of my things so now to the glue gun glue gunning part I'm sorry my mouth is just not working with me today now I'm going to take the body glue the top of it or which ever top you think is the top then I'm going to take the other one try not to get a glue gun by the glue gun because it hurts then you just stick them both together and yeah there we go just do de it do it ok and then that's there and now i got the sniffles and I'm going to take my wings that means

Please explain how to kill green algae

oh that unwelcome Macedo going to the mount white palms go green how to cure that problem so this time of year when the Sun comes out and the fish start feeding most people's cones go a horrible green color can't see the fish and disappointing for everybody involved what makes your pond go great well when the Sun starts running down its providing a source of light for the algae algae is a photosynthetic organism and obviously more light would equal more growth but to grow it will also need food at this time of year the fish will start waking up and start feeding are you obviously going to start giving them the food and when fish feed they will also prove I'm who's going to come out of them and it's going to create a source of nitrates and phosphates and nitrates and phosphates is the first laser that the algae needs in addition to the sunlight to grow there we have the main reasons why your ponds will go green sunlight and food and there's not a whole lot you can do about this other than covering your pond up or starving your fish neither of which you really want to do so what's the solution to green pond water well let's go through the three ways that you can make your pond water to go clear and you don't have to use all three of these you can use any one of them or any combination that you like and they can all be effective on their own so the first way of making your pond clear is to add a filter with a UV or today UV as a standalone addition to a filter that's already present in your pond so UV light is basically exactly what it sounds like it's a tube that emits UV radiation now UV radiation or UV light is particularly bad for living organisms so the way UV light works is the water in the pond will flow through it get hit by a dose of UV light and that will kill the floating algae within your pond it will then be taken out normally by sand filter media within your filter out will come clean water doing this for long enough your pond will become a clear paradise for your fish then you draw back to using a UV light is you will need to change the bulb every year to start the season preferably and that is an added cost however they are very effective at doing their job the second way to make your pond go crystal clear I do use chemicals now I'm not a huge fan of chemicals being put into ponds however they can be useful in their own way one of the more natural ways of clearing a pond is to use a thing called barley straw now is exactly that it's just barley straw in a bale that you're throwing your point to start the year and it rocks it releases hydrogen peroxide and that will kill the algae in the pond it will also kill blanket weeds so it's a bit of a double-edged sword there's no real drawbacks to using barley straw and many large government agencies use it as well other chemicals available are potent algae sides which target floating out in particular and also ones that are flocculants basically mean the algae will stick together full spot on the pond or be taken in to filter and removed by the sponges the drawback to both of these chemicals is that they only work for a short period of time and they don't stop the elbe coming back so you have to keep using them if you want to keep your pond clear also some are more effective than others and the are generally quite expensive third way of creating crystal-clear pond water is to remove the food available for the algae even if it's plentiful sunlight here on days like today is make food for algae there won't be any outlet how would you do that well this is the most natural method and also I feel best looking nice to add lots of plants to your pond now as you can see this pond is actually pretty small so that 500 liters probably slightly overstocked however the water is crystal clear and that's because there are many plants in this pond now all of these plants will be sucking out nutrients from in this water that means Paul appeared on the food goes into the pond won't get conversions algae they get converted into red flowers that's just the way I like it the best plant flier in your pond are read like these and irises because these are the most effective at removing nitrates and phosphates from the front water however any plants will do the job as long as there are a lot of them now I personally prefer the planted roots to clear water however any of the three I've mentioned will work just fine I would recommend if you're going to use any of the two to use the plants and the UV roof because that will give you crystal-clear water pretty quickly so if you like this video please remember to subscribe and like the video below leave a comment and give any questions or suggestions thanks for watching and happy fish keeping

Please explain how to make takoyaki | japanese octopus balls | たこ焼きの作り方

two of a sucker's favorite snacks okonomiyaki and takoyaki economy a key being the things that you like fried sometimes called a Japanese pancake but this is the other one takoyaki octopus ball of course he can't have takoyaki without octopus so this is where we get started I don't dwell on the octopus too much it's really just one piece of octopus that goes inside the octopus ball in Japan people would normally buy the octopus pretty cooked but here my eye all I've got to do is really just boil it this octopus has already been cleaned that means has had the beak and the insides removed already so all I've got to do is put it into this hot water and you can see it curl up immediately as it goes in there that'll take about 30 minutes 45 minutes to become tender enough for our takoyaki now for the takoyaki batter all we need these ingredients here some plain flour a couple of eggs some dashi soy sauce and a bit of salt start with the flour first and crack my eggs into the center there's a bit of a whisk start adding in mabashi I want to add the dashi a little at a time and incorporate the flour gradually so no lumps in my batter and when all the dashi is in I'll add my soy sauce and salt you can see how thin and watery this batter is that's exactly how a takoyaki batter is supposed to be this thin batter is going to give us a nice crispy outside and a fluffy inside Marc de bus is ready and now let's talk about this this is my takoyaki machine you do need one of these for Takayuki but not specifically a takoyaki maker this is just a heating element with this kind of indented hot plate on top then you can even use one of these this is a aebleskiver pan a Danish pancake ball maker and you can buy electric versions of these that are actually often refurbished Japanese takoyaki makers in quite a lot of electronic stores you know look for a Dutch pancake maker or a pancake or maker and sometimes you can actually find a little octopus symbol on them which lets you know that that was once in Japan made as a takoyaki maker I'll get rid of this and they prepare my octopus now I don't need all of this octopus but it's nicely tender now so I just cut some small pieces of octopus and for this red pickled ginger I just need to finely chop bad and now on with the takoyaki maker make sure you do stir your takoyaki batter because it's so watery sometimes the flour can sink to the bottom nice and hot now so a bit of oil to each hole and when you fill this up with better you want to fill it right up over the holes and actually fill up to this lip that's around the outside there you can just see the outline of the holes there so one piece of octopus into each hole and then over the top of everything is ten cuss tempura batter bits bit of spring onion and our pickled ginger as the butter starts to foam you just want to draw your skewer in like a crosshatch pattern that goes between the holes and push any overlap into the holes now to turn them you stick the skewer right to the bottom kind of do a half turn now as the batter starting to crisp on the outside just keep rolling the balls over and start to see it becoming lovely and golden brown the secret to a good takoyaki is for it to be lovely and crisp on the outside and fluffy in the middle they look fantastic so I'll pull those out top these with some takoyaki sauce and you could really just use a regular barbecue sauce if you want it but the two most popular brands of tacky Aki saucer or two fugu or bulldog and can get them from any Asian grocers some mayonnaise as well this finishing process is very very similar to making okonomiyaki so it's a sauce the mayonnaise and a few little sprinkles on top power Lorre the green nori and last but not least some bonito flakes now I don't usually tell you the recipe I'll be uploading next week because I don't usually know but for this takoyaki I'm gonna show you a variation in next week's recipe it's gonna be one of my absolute favorites cheeseburger takoyaki but for now we are done you're suckin street food classic takoyaki you

Please explain how to make seed pen

with a pen I didn't elaborate on a Samba on the video tape or a program refill Lickety record sheet all adapt name is pawel corresponding la manera I'm Iranian via stock on tape or Lebanon immunised Obispo Nicola a video later innovate CT spawn trap reef aloha mai kakou a rifle an umbrella specialist a moral order said Allende now make an apology now on no Vulcano plastic reflation dakara nonde panama dream el condor white cedar to give the soup a little arrow NOLA a Gurkha did yoga Maggio determined in our room by linear data governance Fe College Pune mantra Nilayam Ida corresponding la nuit dalla genealogy when you open botanist and Iroh so are they responding to anima banner ad I'd say let me on a cup devotee day last part undercut Pony to fill up a bit today a little too clever that now in the activity on the entire canal and is ponder and buddy-buddy opposed to do on the money pocket even the molecule Madeira the governor miss ponder last moment acute Aleppo Sangha the quantum computing and okay they are poor turning on the gum you spawn trap Iraqis polyglot I'm the refill now concept overlay today I will add my cap or iron grip Nazca have gum wad city look on your chin a bit the paper roll oj john pineda three people inaudible TV knock on the Stanga Oh am ia the Musab agree you are gonna go guess what an all around it has got how do you H stamp eight Pony of that I died on it so now nobody Connie dead from weapon on the whole Grady I'd see the corner Mahmud II see no the pepper rosin already send your children record pani I per se llaman dreaming of a fall open is a young explain phenomena is liable to see another partner let me on a dynamo casting quantity number on the panel on the Palazzo check for level math logic for Oh Luca Hippolyta ocean Mikado people plastic image into to tear away Bella and run ammonia bleep temporal anomalies Ponte Polo route opened a new cast accordion la donna ni yoku hydro Gabbana - hi dog of America honey Nevada what a piranha submarine de la Cucaracha go classic la da la otra Bamba Remo Moody ready element potenuse Amarillo Nguyen do mundo show Angela Novello person dirimu do : Angola Sheila moody or a top positively owned in the mail topic line I love running Weather Watch ecological on another killer the Montebello children granary videos in Jakarta on collect the mail put him at ease your telegram mucho determinate was tango you go to creativity done with Milano will go basically tonight here the couple no creativity not but banner adhe now and already in my perilous injury French little crooked rude and ever say every angle contributed to that maria-paz you can almost carter de jambe edo edo modem el condor comfotable de areco one month linked in the bell jeolban and apparently to you purine led a poor monoplane voted on domo legend arrow al de volcán de Marchand Irma Alejandro con artists panna cotta tahun upon banana now oriented in the path that Monica de la have been saluted oh yeah Holly the male child Richie I'm going jello good under same thing labor clock on I'm ready number one they're gonna get a new movie name a moon Angelo good plastic or chipped a seed panel on the Hispano partner thank you so much

Please explain how to identify and control problems with pecan trees

(mellow music) - I'm John White. Today we're gonna be talking about some pecan questions that we've gotten. And, one of the things I wanna give you is some basics on pecans. This is considered a leaf on a pecan, and each one of these individual things a lot of people call a leaf is actually a leaflet. So when we talk about leaves on a pecan tree, we're talking about this whole thing. And we need 15 of these for each pecan. So, we wanna produce and keep as many leaves on the tree as possible. So, it's very, very important for a pecan to produce as many leaves as you can, so you do not wanna stress the tree in any way. So again, 15 of these for one nut. So, we need to have a lot of leaves on the tree to have a good crop of pecans. So, this is the bare basics. Now, some of the insect problems that we're starting to see this time of year is we have a yellow pecan aphid or what we call a black margin aphid. And, it's a little tiny aphid that's on the inner side of the leaf. I don't know if you can see this one very well. There's a little kinda yellow speck right near the mid rib on this leaf, and that is a aphid. It's sucking the juice out of the leaf. As it sucks the juice out, it excretes the juice out so you start to see a sticky honeydew. And, this time of year with the starting to cool off, the aphids are back on the trees, and we're getting a lot of drip from the honeydew. If you have a car underneath a pecan tree, you'll see the drip all over the leaves of the I mean all of the windshield of the car, and then as it falls down through the tree, you'll find a lot of the leaves have a lot of drip on them. So, this is an aphid. With this being September and going into the fall of the year, we can probably withstand some aphid damage on the tree, but if it's a heavy amount where the leaves are very real sticky, we may wanna look at using insecticide in order to help keep the quality on the crop. The other thing we're looking at is these leaves right here have kind of yellow spot with a dead area in between it, that's called a black pecan aphid. And, on this particular leaf, you can see a little spot right here, little black spot, little black dot. And that is the black pecan aphid on there. When it feeds, it puts a toxin into the leaf that causes a dead spot in the leaf. If you have enough black pecan aphids on the leaf and enough spots created, the leaf will fall prematurely. So, you may have leaves falling on the ground before actual cold weathers come in. So, that will reduce the leaves that help the tend that crop on the tree. So, we don't want that to happen. So, we wanna be sure and get that under control. So, if there's a lot of black pecan aphid damage, you do need to spray. They're fairly easy to kill. So, insecticide is easier to find. Now the other thing that we're finding on some of our pecans, this is a third-generation pecan nut casebearer that is hit. We are seeing that on some of the pecans. It may cause the shuck to stick to the shell and make the shuck very hard to pull off the shell. So, depending on when it hit, it won't get into the actual nut because it's already formed the shell on it. But, this is a sign of pecan nut casebearer. There's nothing you can do right now. You just wanna maybe start working on getting a program together for next year so that you can control it early next year. So, pecan nut casebearer is something that we see on some of the pecans. And the other thing we've seen is just a lot of pecans beginning to fall off the tree. Some of these can be pecans that maybe didn't get pollinated well or possibly the tree has a heavy load. This is an on year in the pecan industry, and you do lose a lot of pecans off of a heavy crop just due to the load of pecans that are on the tree. So, maybe a little bit short on water. There might've been some other kind of stress problem on it. So, this is a problem that we see. But again, about 10% drop. So, on a heavy year it's gonna be a very noticeable drop. So, again this is something we expect, but as far as the pecan tree, we do wanna get our last waterings, last irrigations on. So, we wanna continue the watering of the crop all the way through shuck split. So, when this shuck begins to actually split on the pecan, you can carry the irrigations on through there. So, we may be talking about on end October and possibly even the early part of September, I mean November. So, we wanna keep that in mind. So, hold off on the fertilization, but do continue with watering and then be sure and identify your insect pest, and you'll have a much healthier crop of pecans. (mellow bass music)

Please explain how to fill brandy snaps with mary berry pt 3 | the great british bake off

Please explain how to get to watch free tv, installed in your car legally!!!

I'm going to show you how to get free TV in your car stay tuned I'm going to show you how to install free TV in your car and also hook up a PlayStation 2 full entertainment system in your car and I'm going to show you everything you're going to need i'll list everything all the products in the video description below but here's just a few items of course I got the ps2 I got the splitter so I can switch from AV 1 and AV 2 I got my car stereo that accepts on audio/video inputs and I also have gone this cable and off air TV box this is a digital converter box even even though my car stereo has a built-in TV tuner it's it has an analog TV tuner and my area Tampa it's actually all digital TV now so I need a digital converter box and also all fair antenna and also got an AC splitter so I could connect the ps2 n the TV box and I got a power inverter which plugs into my cigarette lighter and it converts 12 volts from my cigarette lighter to 120 volts AC and this is up to 150 watts and it has USB outlets so you can charge your phone alright so right here I'm going to plug in my power inverter which is zip-tied under underneath my dashboard and this goes to the extension cord the extension cord goes under and I just gonna lift this up you just pretty much tuck it under you see my fingers and just push it in there and I ran it right here in my center console box and plugs into my cigarette lighter port right in here in my 2006 Mustang for some reason when my car's turned off my cigarette lighter ports are still active I don't want to kill my car battery so I I connected a kill switch and just basically cuts the power from my cigarette lighter port that's on and that's all if you want me to do a separate video how to connect the kill switch to your cigarette lighter port just leave a comment below and I'll make a separate video for that now I got an inch and a half pull so I'm going to drill a hole in my glove box all right so I drilled about almost a two inch hole in my glove box this is for the exhaust so the ps2 doesn't overheat and don't worry there's a air up here this is all open above here so it can still get fresh air and then exhaust a hot air out through this hole so this is the exhaust right here and this hole is big enough to run all the cables in - now I'm going to go ahead and connect this off antenna in here for antenna now I'm going to run the power cable for the ps2 I got this AV wires connected to the output and this is going to connect to my car stereo AV input and back in my car stereo okay so what you want to do is you want to plug in to your video input on your radio yellow goes yellow white goes the white red goes to red so the audio is plugged in and the video is plugged in okay so I got the AV cables coming from the car stereo AV input right here and I got these AV cables on the output and that's going to connect to my car stereo video the yellow and white is the audio and the red is the right audio and AV one I'll have the converter box plugged into right here the a/v one input and then I have the ps2 connected to the AV 2 just like that now when I switch right here that's ps2 mode and that's the digital covert TV box right here and so whatever I select it's going to toggle to the output and I got my guerrilla tape on it I'm using Rumble rubbing alcohol to clean the surface let's go ahead and just mount this on the side right here and I'm going to send these cables down here and that's going to go to the governor box and I have my anti skid mat just place that right there power cable from a PS to my AV cable got some zip ties clean this up let's go ahead and set this in now push this all the way in that's why I made the hole so Vegas because I needed to push those uh those plugs in the hole opening and closing it works now this power inverter down here mounted I'm going to hook up the splitter to it now I have the wires coming out from the glove box this is for the digital converter box and this is the off an antenna plug and this is for the power for the ps2 now I'm going to zip tie this under here okay zip tied the power brick to the wire harness underneath my dashboard now my TV box I got a mount I'm just going to use an L bracket right here and look inside that vent there's nothing in there so I put a screw in there and hold it in place the video outputs antenna plugs in right here all right I'm going to select my AV input maybe in turn on the kill switch cigar lighter port is active turn on cable box or TV burner box he's changing them mm I like almost 50% signal and then antennas in the glovebox you want to hit menu now now you can do a channel search and you want to do an auto search it takes up to 45 minutes to auto search all the channels and then I'll basically program all your channels to the but I have selected antenna power all single type is not cable but to off the antenna and that's all you got to do really and then want to search through channels and then when I switch PS to a b2 press the power button and I got the wireless transmitters or receivers wires receivers for the controller and now when I want to turn off my car turn off my car just like this and hit that kill switch and everything turns off my PlayStation the cable box won't the TV box and inverter everything turns off so I won't drain my battery if this video was informative give me a big thumbs up if you want more how-to videos like this coming your way click on that subscribe button right there now if you know anyone that this video may interest go ahead and click on that share button and share it to them thanks guys for watching and check out my car electronics playlist

Please explain how to fold your socks usf rotc

I will now demonstrate how to properly fold as your word roll a sock first trying to make sure they are generally straight you can do so I'll put your hand inside the sock and strengthen it out like so you want to straighten it out as if you're wearing it not the side view that most people have it at but like you're wearing it as you can see like you're wearing it do the same thing with the other sock at that point you put one sock on top of the other with the heels facing downward I say again with the heels facing downward at that point you wanna make sure everything is generally straight and aligned with each other right on top of each other make sure you take out all the kinks at the top make sure that it's generally straight at that point you will fold the sock up to the heel like so making sure everything is jabbing you straight make sure you maintain attention to detail at that point you start rolling from the heel and pulling on the sock pulling on the sock to make it nice straight and hard a nice tight roll every roll do a little tug make sure you're pushing in the sides as well the end result should be like this at this point you grab the top suck the top sock and the top flat you would then fold it over the whole sock you need to make this guy disappear I'm putting the sock over that partion of the sock forming an oval trying to get these kinks out my stretching it out and that's the only thing you should see inside there when you flip it around the top should form a general smiley face at that point compact it keeping it nice and tight that is how you properly roll sock

Please explain how to plant a meaningful flower pot for your porch

hi everybody this is my first video she'll bear with me I'm just learning how to use my camera it's the most spring time so I get the itch to plant and I like to pot plants and place them around my yard my front porch and I did my first planting today or yesterday actually some specially picked flowers that I picked out for special meaning and what they are is the daffodil for fertility the Primrose for protection and pansies for love and I also added a little gazing ball I placed in here to ward off evil intent negativity so it's just a nice little fresh look to my porch for spring coming up I cleaned really well hung up my protection wreath on my door and so I'm going to go ahead and show you how I made the first pot of the year okay so you're going to need a few supplies and you'll need a container and you'll want one that has holes in the bottom or drill them yourself or use a hammer and nail and punch some holes in the bottom just so the excess water can drain out the also good idea is to have some rock at the bottom this helps with drainage as well you'll need some a watering can or water you'll need some soil you can use any soil that you want but I really like the Miracle Grow because it has fertilizer in it already and it helps take the guesswork out of odor over watering and you'll need your plants and I just have the daffodil and the pansies and the Primrose so what we're going to do is fill the containers about halfway full and I just use fill it up halfway you're going to take your plant your first plant and it's good to squeeze it to release the dirt and you always want to kind of massage the bottom of the risk and loosen them up so they happier when you plant them press them in there get your daffodils same thing little pepper yeah they get a little root down so you want to loosen all that up and no matter what kind of plant you're planting listen here get your pansies and these are nice because they kind of it kind of trail over the slide they get bigger then you can add small dirt soil and it's kind of nice to have a place to plant outside you could do it in your grass or a table because it looks pretty messy and circuits everywhere but okay can sweep it up can your outside a little easier you just want to make sure the roots are pretty much not showing if you can see press the dirt down tight look at that and then next you want to water you're going to water it really really well I'm just pretending I'm watering right now but you just want to get the soil really really soaked the first time just to make sure those roots have good moisture and that's pretty much it that's pretty easy pretty easy little plant there and it's really cute on your table or your back patio or on a little stand and what you can do is add any kind of little meaningful statue like a troll or a no more I really like fairies and so I may just get a little fairy and set her in there and have a little fairy garden so I hope you enjoyed my video and thanks for watching and I'll do more now that I know how to use my camera yay bye

Please explain how to: clean a bong on cheap budget!

what's going on guys listen to random here I want to show you guys how to clean your dirty blonde yes you see the black stuff right there mm-hmm that's disgusting that means you smoke too much and the easy way out how to clean it with just alcohol you see right there where it says 149 if you can't see it that's what it says and good old and the kosher salt that's all you need regular alcohol and kosher salt let's get to it now this is what your bong is supposed to look like the dark stuff and what that means you smoke way too much so what you wanna do versus pouring Penny's water take off any accessories that's what you want that's real and alcohol than 14-hundred any nonsense doll I have cultures I'm getting all should do and I would need to do is roll ups and tissue a lot to show you in a few stick it right in there so you gonna be holy and on top hold it in the bottom I'll shake it up and down now that your bullet your tissue you want to stick it into this hole you see how clean I got in less than what ten seconds now you see how cleaning out was just 10 seconds of shaking now is top of this what I do is not always clean my ball twice and then for the last time I'll hook this in to make sure is entertaining there's all just to be sure rolled up another tissue I stick it in there put your finger do whatever you do best do the same process you do your song just let it go to work and as a matter of seconds you couldn't tell the difference where do you see the heavy spots even away which the easy stuff already broke now and this is your final product a nice sexy clean bong call her I buried the second [ __ ] mother now the best thing for you to do is to let her dry say for about a day or you know a few hours because the alcohol fumes are still in there so just to be sure that her dry out you might have little tiny spots that look a lot he has in a few days she's gonna be black as hell again so listen around you

Please explain how to fix a stuck or frozen lawnmower pull cord (easy)

hi everybody thanks for watching you're looking at the MTD 20 inch cutting width mower with side discharge this is about a year old and I wanted to show you something that recently happened this is over at an apartment building we own and one of the tenants is responsible for doing the lawn and he is but the most unhandy person ever so he called a protect and crying it can't he can't get it ready so I went to pick it up brought it home and here it is try to pull this and I'm not going to concern casual inspection would say what's going on we're turning over on the side started with one hand goes over here a little tripod Freddie go okay do you see anything out of the ordinary under here very help yeah there's the blade in the middle and there's the black curtain in the back that is supposed to protect you from debris flying out that he helps we pulled it backwards to start it in the debris shield with him and block the blade so he did to himself see how that debris shield hangs in the back that's how you do it that one I bet this turns so we'll prime it start it right up

Please explain how to install a box newel and handrail (knee wall)

hi this is Patrick with advanced staircase today we're going to show you a basic installation of a box Newell and a knee wall normally the knee wall will come past the first step out here in it would be notching the box they took a lot of times about half way to push the knee wall that I put to push the box a little back on the knee wall in this particular situation they had it knocked for the old post so where you we opened it up so we can put our box a little flush to the front of the knee wall this is the knee wall if you're not sure what I mean by that term the slanted board it goes along top of the trends here so we already cleaned up our notch here when you're putting in a box the hole the first thing you need to do is get it in the position where it's going to sit front to back because we have to get our proper height for our boxing so again if the neat wall came out further you would kind of set it behind here approximately let's say that it was going halfway on your knee wall and that's where it would be placed front to back and you would do your measurements with it sitting here then after you got the right height you'd go back and notch it so we're going to put piece of the handrail on top of our nail wall and measure to the top of the handrail from the nose of the stair tread in this particular situation it's right at five and a half inches and when it's installed we need it to sit from the nose of the stair tread between 34 to 36 inches of course check your local codes but most places the height of the handrail from the nose of the tread is 34 and 36 inches we're going to put it at 35 inches just to give us some room for error and something if we're if we wanted 35 and we're at five and a half we're going to have to go up twenty nine and a half more inches so what's gonna do now just put a mark right where the top of our handrail it's the the Box alone right now you may not be able to see that but you can see what I did we again knew all the rails at the top of them you all put a mark right there we're going to measure up from my mark twenty nine and a half inches okay when we cut our handrail to go on the box though we're going to be cutting it up on this angle and when we cut our angle it's going to be approximately three inches from top to bottom we're going to want that to sit in the middle of our that where it's going to hit the box Knoll and that's six inches so we're going to want in this particular case in inch and a half from the top that will give us an inch and a half to the bottom so that will place it evenly in the middle bar box and so we have our mark where our rail would be hitting right now twenty nine and a half inches and we needed it to bring up there so we're going to be cutting off 8 and 1/2 inches to bring this down this mark down to this lovely okay we cut the box level and come back okay we've cut our box tool and going to make another mark where our rail is coming right now the top of the rail again there's our mark measure up to our from our top of a rail now the birds going to go twenty nine and a half inches so twenty nine and a half plus the five and a half here will be 35 inches for a 35 inch rail height okay next I'm going to show you a little bit about the mounting if we were notching the box bull again when I talked about here if we were going to notch it for to sit halfway on here we make our mark where we're going to notch it cut this piece out of the box no and then put it appropriate amount of this block up against here for it to sit on also just not this particular case how we're going to mount it in this situation we're going to put the whole box no here again most of them with the new all you're going to be notching it you're going to be cutting your mouth you block probably in half mounting it up against your knee wall and then bringing it in that direction in this situation what we're going to do since we're going to full box though the monkey block is going to slide in then what it stops leave about an eighth inch from the top market words can become never line and cut the block and then the extra if we cut off the bottom of our box no we cut up approximately a one-inch piece of it so what we're going to do is mark where that's going okay and we have a market where we're going to mark our block for the boxing okay we're going to cut this comeback mount it and then show you down install ok we're going to start by putting some adhesive or the mounting block is going to go and you don't need too much down here because it's going to push most of it out when you screw your block down a little bit it adhesive there definitely prefer this is called peel premium it's much stronger than liquid nails or pretty much anything out there don't Dorse a lot of brands but PL premium will hold better than anything on the world ok I'm going to take this kind of spacing block here so we get our post nice and tight up against the new wall and then we're going to shoot a couple of nails before we put our screws in there so the nails will hold it in place where we need to be until we screw the block in okay and it is a little bit stuck but we want to cut up against the meatball okay now we're going to we know they're blocking place its hold it from moving around we're going to take some heavy-duty screws he's use an impact and drop a minute make sure they go in pass the flush part so the box level is a hang-up on it while you're trying to put it on now we're going to put peel premium on the inside of the box little make sure you get all four sides the nice thing about this also is it expands as it sets up so it will fill in gaps and it will be rock solid okay we have all four sides with PL premium in here we're going to put a little bit on the knee wall and just on the inside lip here just to get a really strong bond so this whole piece is rocks out okay now we're going to slide our box little down it's a nice tight fit piece of trim here just okay nice tie fit we're going to get a level square it all up shoot a couple nails to hold it in place until it sets takes about 24 to 48 hours to fully set up okay we're going to make sure our post is level both directions good that way all right now we're going to put a couple nails okay we're going to get an initial angle on our handrail to cut it so we're sitting on top of the new wall just get put a little mark they'll be an approximate angle they're usually near a forty degrees so that's a good starting point again it's just an initial cut all right we already have this end cut we already did that and see when we bring it in it's it's there pretty close fit to our to our angle good starting point okay we clamped in its spacer block here to hold our rail up at the proper height and we worked on our angle to the guide perfect here okay we're at a actually a 39 degree angle it's going to be different with every staircase so but in general all if it's 39 here we'll also be up at the top so we have that part set okay we have a four-foot level and on our level we marked our 34 our 36 inch mix you have three months 34 35 and 36 we're shooting for right in the middle we're ready check their bottom or right at 35 inches we put the level at the front of the nose of the stair tread and we're going to put this level right there we're right at our 35 inches there so our rail is edits right at the right height and it's consistent okay we want to take a rosette this happens to be a square rosette goes well with a with the box no I'm going to put on our wall so it's nice and flush we actually have it up your backwards put a little mark top and bottom that's where we need to cut it so the real Zeppelin fit in there and okay we have our rail or cut we did have to cut an angle on the top piece here because the wall is on quite a bit of an angle so we'll take a little time to get all your angles right but go a little bit at a time we mark to our rosettes going to sit height wise now we're going install everything we're going to put up again use a little bit of peel premium you don't need a large amount Center it in the mall put a nail where the rails going to cover up this holes you have to fill make sure you're nice and straight so put one in straighten it up okay a couple more okay now we'll do the red okay we're just going to put a small amount white glue spread it out on both ends in the rail good nail it first and I will come back and and put a screw in there just to give it some extra strength measure make sure even on both sides make sure the centered up here okay get a good wood good quality wood filler usually if you go to a hardwood flooring Supply Company they'll have a better wood filler and you'll get it at Lowe's or Home Depot kind of place and go back although where we shot nail holes just go back and this is a red oak so we have a red oak wood filler push it in there and you don't have to get crazy just make sure it's flush and fill it all your holes then we'll come back and give it a lights and that's it

Please explain how to repair a guitar hero whammy bar !

hey YouTube this is Google dude one two threes first video and Google means like to tutorial stuff and the first video will be how to repair a broken whammy bar like mine has no spring in it so it doesn't work in yet and I'll show you how to repair it first of all you elastic bands and this or hair bands like this depends which kind of elastic you have so I take two because they're not really thick elastics so first of all you need to put this on your wine bar and attach the other end to the strap thing I don't know what it's called the black button thing for the strap and now I'm gonna put my second one this and should work perfectly I hope you liked it all questions will be answered in the description box hope you enjoyed this video hope it was helpful I have fun your wine bar

Please explain how to replace laptop dvd/cd toshiba satellite c70. fix, install, repair c55 c850 l55 s855

laptop inventory calm your source for laptop parts notice the repair process is different for every laptop model at laptop inventory comm we have created a database with thousands of free laptop repair videos simply go to laptop inventory calm select your laptop brand series and model and find the exact repair video for your laptop turn the laptop over remove the laptop battery remove the screw remove the plastic bezel remove the optical drive we will now install your new optical drive snap the plastic cover back in place that's all you just installed your new optical drive laptop inventory calm your source for laptop parts

Please explain how to make a volcano

my name is Margaret Morgan I'm a science educator I work for a company called mad science so today we're gonna talk about volcanoes and how to make them first we're going to talk about real volcanoes and what makes them erupted and then we're going to talk about different ways to build a volcano and then we're going to talk about different ways to make your volcano erupt so the materials that we're going to be using today to make our volcano first of all we have air dry clay which we're going to use to actually construct the volcano itself we're also going to use this bottle we're gonna have this inside the volcano it's gonna this is where the actual reaction is going to take place and here we have some wood this is just gonna be for decoration around the volcano and some trees also just for decoration and here is our vinegar and our baking soda your basic ingredients for El volcanoes are baking soda and vinegar but to make a more exciting volcano you might want to add you know food coloring to make the lava you know red or orange we're going to use kool-aid today it's red so we're gonna use that to color our lava and we have gelatin here gelatin makes your lava chunky and then we also have diet coke and mentos that's gonna be all our alternative magma today so we're not working with anything too dangerous today it's basically gonna be baking soda and vinegar it is an acid-base reaction but it's a mild acid in a mild base but you know just make sure you have an adult around when you're doing this and it does get very messy so make sure you're prepared to do some cleanup as far as my credentials go I have a bachelor's degree in biology and since I graduated from college I've been working as a science educator I worked at a local Nature Park in their nature science summer camp and since then I have worked for Mad Science so I go to schools all over Pinellas County and teach kids about science and inspire imaginative learning by making volcanoes and making slime and doing all sorts of fun stuff like that alright in our next clip we're going to talk about real volcanoes and what makes them erupt you

Please explain how to get rid of mole in your yard

hi this is John Oaks I am the author of ultimate mole control it is the number one selling mole control book and course on the internet today I wanted to film this quick video just to give you a little bit more information about the course a little background about how I came up with this so what I'm going to have you do is take a walk with me real quick let's go this way we're going to take a quick walk through the yard here so that you can kind of get an idea in a feel for the expansive nature of the landscaping that I was dealing with when i had my mole disaster my mole problem what I have here is actually a four acre piece of property and two acres of that are fully landscaped so I had you know essentially an acre and a half of lon space and a whole segment of beds all the way around that that I had to deal with mole issues with so as you can see there's a lot of lawn to deal with alright so welcome to the front yard what you can see in our walk around the house is that there's a lot of space to deal with and I had quite a mole disaster in fact when we first landscape this two acres on this part of the property we were literally coming out almost every other day and finding as many as 15 to 18 mole holes every single morning so what we had to do is literally come out here with a wheelbarrow and shovel that dirt and there were times where my wife and I would fill the wheelbarrow a couple of times with new fresh dirt that was uprooted by those moles it became quite a disaster and some of you already know what I went through and know the anguish and the frustration that I dealt with but I literally for the course of about two and a half to three years tried every possible solution under the Sun I spent close to a thousand dollars on gimmicky products sound devices bait traps everything I could possibly try I tried it so I can tell you from experience that most if not all of those gimmicky products simply do not work some of them work a little bit but just enough to cause a lot more frustration so I developed my own sort of formula for setting traps I also discovered which trap out of the nearly a hundred traps that are on the market was the most successful that worked the most often in any climate and soil conditions so after doing that and perfecting that over the course of about six months I completely eliminated my mole problem now when I say completely eliminated because I am right next to another two acres of basically forest land I will always have the occasional mole that comes into my yard however because of the trapping system that I now use I can very quickly trap that mole and eliminate it from my yard before it causes an immense amount of damage so some of you who may not be seeing the value in this course at this point you probably need to get a little bit more frustrated try a few more of those gimmicky products so that you can get to where I was when I would have been willing to pay as much as a couple hundred dollars for this course however that's not what I'm going to charge you for it in fact I'm not even going to charge you a hundred dollars for this course I'm not even going to charge you fifty dollars for this course as you can see when you scroll down the page to see what the price is that it's far lower than that and it's really a no-brainer if you have a mole problem simply by the course go through the course watch the training videos in fact there's one thing that I wanted to share with you to sort of illustrate the frustration level that I reached when I was dealing with my mole problem and that is there was a time where I was literally up at the crack of dawn with the 12 gauge shotgun walking around waiting for any type of movement in the soil so that i could start blasting at that hole I did this for several times in fact and of course never got one that way the funny thing is I now hear one of my neighbors off in the distance in the morning shooting it at his molehills so I probably need to go over there and talk with them anyway I hope that you see the value in this course and I hope that you find this useful and I look forward to helping you get rid of your mold problem

Please explain how to make apple haystacks : healthy ways to prepare apples

hi I'm Jill Shepherd and I'm going to show you how to make these fun apple haystacks haystacks can be made using a variety of ingredients today we're going to shred fresh apples and pair them with raisins gluten free pretzels and peanut butter pre-heat your oven to 350 degrees Fahrenheit and prepare a baking sheet by lining it with parchment paper I've just washed one large apple and cut it into thin strips with the peel still attached place these Apple strips into a bowl filled with cold water and 1 tbsp lemon juice to keep them from browning before we use we're going to drain the Apple as well in a small pot on the stove top I've just gently warmed one cup of crunchy peanut butter when it begins to thin stir in 2 tablespoons pure maple syrup and 2 tablespoons cornstarch or gluten-free all-purpose flour I'm using a special gluten-free all-purpose flour if you're baking gluten-free be sure to select one without any bean flowers in it to throw off the taste continue by stirring in one half cup gluten-free or regular pretzel sticks add one quarter cup raisins and those drained Apple strips compact and spoon scoops of the mixture onto the parchment lined baking sheet if you're serving the desert with a fork the scoops can be larger if you're making these for bite-sized treats spoon small scoops onto the train instead this recipe makes about 20 small haystacks or 10 larger ones bake for 20 minutes and remove to cool once they're cooled they are no longer so fragile and it's easy to eat them with a fork or as bite-sized treats

Please explain how to replace a light switch

this video will show you how to replace a light switch remember before working on any electrical circuit be sure to disconnect the power at the main circuit breaker panel first we remove the wallplate by unscrewing the two screws then unscrew the two screws holding the switch onto the junction box using your phillips screwdriver unscrew all three wires connected to the outlet switch then making sure you match up the wires with the appropriate terminals on the new switch screw the wires back into your new switch reattach the switch to the wall then put the faceplate back on with both screws test the new switch to make sure it works and you're done

Please explain how to prevent candle tunneling

hello everyone we're day with food from candles of Maine and this is the main event the number one show for everything you need to know about luxury home fragrance and today we're going to talk about candle tunnelling what it is and how to prevent it the first part of preventing candle tolling is on the part of the candle manufacturer themselves they've got to select the proper wick for the wax the fragrance and the size container they have selected if they've done all that correctly the candle should tunnel if burned properly and nowadays going to talk about how you can help prevent candle tumbling the best way to help prevent kim candle tunneling is to make sure the first time you burn a candle that it gets liquid the whole top gets completely liquefied this one as you can see has done that throughout the whole candle there's no wax on the edges or sides and that's a really good burn that's burned very well since we started burning it this on the other hand was burned wrong or improper basically when we started burning it if we burn it for maybe an hour obviously the pool did not go to this it did not get completely liquefied and this is what happens and then once this happens there's really no turning back what the candle will continue to burn like this unless you either get rid of the excess wax or burn it down but basically you need to do something or you're not going to get a full burn from your candle that's right and a good rule of thumb is about one hour for every inch in diameter so this candle the very first time you want to burn it about two to three hours let it go to try and get the entire top look at wax so that it runs evenly all the way that's it for us today as always we love to hear from you so please feel free to leave a comment beneath this video and you can find more information about candle tunneling and other candle burning issues on our blog since navcom if you like this video please like it on Facebook and YouTube and subscribe to our YouTube channel and as always we hope it comes to light at candles off me calm thank you thank you you

Please explain how to make lemongrass tea

hi today we're going to make some lemongrass tea this the Lim press we just got is the fresh and you can see from the root to the tip over here we're going to wash it and then cut the roots up this is very woody and then we don't use this one and cut this basically to credit to about two and a half inches and smack them by smashing the lemongrass talk to you when you cook it at the Roma in Scala released easily and we're going to put all in the water hot with two lemongrass rock we're gonna have one gallons of waters and then turn on the heat we're gonna cook this one until this boiling and then after that you reduce the heat to simmer and cook going ten minutes okay after ten minutes you can see the water like this is ready to go at this point you can pick up all the lemongrass you can use a strainer to strain all the lemongrass and with this lemongrass we can use as hub my hot tea I'll call over ice because the lemongrass basically just at the the flavor yeah but then it doesn't taste like sweeten up so if you want you can add a little bit sugars honey it up to your taste and enjoy thank you

Please explain how to load e-books on the amazon kindle paperwhite 3

hey everyone it's Michael here with a goodie reader calm and today I'm going to teach you how to load ebooks onto the Amazon Kindle paperwhite 3 e-reader so here's the picture of the e-reader what we have done is we've taken the USB cable that's come with the purchase and plugged our Kindle into our PC once you do that on Kindles say USB drive mode and what we're going to do show you many different ways that you can copy ebooks cheery reader Amazon makes it ridiculously simple to copy ebooks the normal way but we're going to show you a bunch of different ways that you may not be aware of to allow maximum freedom the first program we're going to look at is calibre this is a free download and on this YouTube video and on our website we'll include a link where to download it it's 100% free one of the advantages of calibre is being able to convert ebooks from one format to another so that is on Kindle definitely does not read the ePub format epubs compatible with say the Barnes Noble Nook or the Kobo e-reader or plenty of others but it's not compatible with the e-reader chances are you may have downloaded some ebooks from the internet and they have not been available in mobi or PRC or azw three of the most popular Amazon Kindle formats so what do we do well calibre loves you to down once you download it to convert it to another format so what we're going to do is right click on the book convert ebooks convert ebooks individually and there's a lot of options here it really gives you a ton of freedom to be able to do stuff but I don't want to confuse you with all of these different options all we're looking at now is the output format and we're just going to do mobi and we're going to click OK so you can see here that it is converting it sometimes it takes a few minutes based on the size of the book but it does give you a neat little progress bar here what it's doing is it's taking the ePub book and converting it to mobi so this book will still be available in ePub format but I also have it available in the mobi format as well so here it is here so you can get the viewer that kind of gives you a look on how it's going to look like on your Kindle e-reader all right now one of the things that you can do with calibre is edit the metadata so you can right click Edit metadata edit metadata individually and here you can do a lot of cool things a lot of books I've noticed from the internet when you download them sometimes it's missing the book cover or maybe the book you know the author's name is the book uploaders name and you may want to change all that so this really allows you maximum freedom so you could download you could click that how do you want the author sort so if you are searching in your Kindle library do you want to search under the guy's first name or the last name so we can click on here and it's going to search by the author's last name if say your ebook didn't have a cover you can click download cover it'll search Google Amazon the open library a ton of others you can see that it's the same book here but let's just click on the Amazon one and I'm going to download the metadata also from Amazon it's possible there we go so you can see here that the rating change from zero stars to four stars you have the books ISBN number as well as the Amazon a si n number we also now have the description of the book so this is a lot of kind of cool stuff that you can do once you're done just click OK now we can send it to our Kindle you can see that we have our Kindle plugged into our computer here and here's all the books that are we have either side loaded on it or have come with the e-reader additionally not only can you add books with calibre but you can also remove them as well so I have say the Kindle paperwhite user manual I can actually remove that book from my Kindle and now it's gone so I want to send this eBook now in mobi format to my Kindle so I'm just going to right click send a device send a device's main memory and now you can see a little check mark here that has added this book to my Kindle so calibre deadly tool not many people are aware of this but the Kindle personal document service is really great for emailing books to yourself so simply all you have to do is click on manage your content and devices page and this is what you see here so this shows me all of the different devices I have from my Android apps to iOS apps but what I'm interested in is Michaels Kindle and you can see here that I do have a Kindle email address here what I can do is I can open up my email client click new email copy/paste that email so it's a Mike special Kindle address here is a great book yeah and I'll just you know do that as long as I attach a book I'll do heaven is for real and send that and next time i sync my kindle that book will be automatically delivered to my kindle so that's really great one of the most common things that people do to transfer ebooks from one device from their computer to say their ereader is use good old Windows Explorer so this is the main route you simply want to click on the documents folder now keep in mind that Kindle is my F Drive but it may be different because I have like a lot of different hard drives on my computer backup drives media drives and so on so it may be different so if it's not f don't worry about it and what I'm going to do is I'm going to just simply drag and drop and this book is now on my Kindle so it will now appear under my library finally Dropbox is fairly popular as many of you know that them is on Kindle paperwhite 3 does have an experimental browser so what you can do is you can visit the Dropbox page and log in under your account and from any computer Mac anything in the world you can just simply click upload I'll click on Nora Roberts the witness click done now you can see I have many books on my Dropbox account that I can just simply access on my kindle experimental browser and download them at any time so that's fairly handy so you've just learned four different ways that you could transfer ebooks to your Kindle using radically different programs and software some of its from Amazon some of it is from third parties and some of it is just simply dragging and dropping but I definitely recommend calibre because it allows you maximum freedom to be able to configure your library on your Kindle to your liking as well as remove any books that you really want don't want on your device any more and if you have any questions or concerns drop a comment below on this video or on the website that you're watching this on and we'll endeavor to help troubleshoot if you're arriving at any kind of difficulties so for getting reader comm my name is Michael and everybody take care

Please explain how to remove weed smells from your car - masterson's car care

welcome back to the shop I'm Greg from Masterson's car care and today I'm going to show you how to remove foul odors and smoke smells from any type of vehicle right here one of our customers came to the shop and he has a 2013 Ford Taurus SH oh there's a twin-turbo Ford Taurus and it really does get driven extremely hard now the customer came in because he wanted some stuff to clean the interior but I noticed that his interior smells really bad and it smells like real bad marijuana now I asked the owner he said he smokes a lot of weed and this thing really does reek of weed so if your car has a strong marijuana scent in the car or a cigarette odors I'm gonna show you how to remove that scent today with our brand new masterson strawberry blast air freshener and odor eliminator now you can pick this up right now on our website Masterson's wax calm and this is the best product that you can get to remove smoke or marijuana sense now I wanted to use this on this customer's car because we designed this from the ground up specifically to remove stinky odors like marijuana now a lot of people and a lot of customers come to our store saying hey my car smells like dank weed how do I get rid of that and so we tell them to use this product because this product is designed with a special advanced odor eliminator built into the product you spray it down and then the strawberry smell it's an organic strawberry smell is designed to counter marijuana smell so if you have that dank Kush smell inside your car you can easily get rid of that using the mastersons strawberry blast air freshener now the best thing about this is everything great comes from California Masterson's car care dank weed also organic fresh strawberries so um one of the most amazing smells with your when you're driving down the highway in California when there's fresh strawberry season the smell is amazing so we use an organic strawberry scent and we infused it into this product and we're gonna show you how to use this product today on this Ford Taurus now this thing smells real bad so if your car smells like cigarettes or weed there's gonna be a great thing to do so first thing I recommend before you use this product is vacuum the car I have the owner actually vacuum the car and then come back to the shop the car is vacuumed and ready to go and what I like to do is I've to roll all the windows down so I'm gonna start the car real quick and I'm just gonna roll all the windows down there we go I'll turn them maybe I'll turn it off and the reason I want to roll the windows down they have any foul odor inside the car you want to roll all the windows down to make sure that you can get a lot of fresh air in here you want to get air flowing in here get that stinky sent out so now that we have a lot of air flowing in here we got the air moving around now I'm gonna go ahead and show you how to remove the smell from this car now the problem with cigarette and marijuana smells is people smoke marijuana they drive with it in the car where they're smoking cigarettes and it embeds itself in all of the cloth interior now this vehicle has like a cloth interior show them the interior go this is amazing right this is like a fabric interior this car is actually a super luxury and has like heat seat heat and seat cooling systems built in through all these little vents so this is really a high-end luxury car and the smell of marijuana smoke or cigarette smoke will get embedded inside of this fabric so how are we gonna remove that we need to find the source of that smell and get it out of here so I told the customer pull out everything I like to check out all the insides of the car there's some stuff here like like some tools and stuff there's something in here I like to remove it this smells like that California could go back I've given the open bag of weed to the owner of the car now it's completely gone from the car so if you want to get something a smell out of the car if it smells like bad food or or if your car smells like weed or cigarettes get the cigarettes out of the car get the weed out of the car get the smelling nasty food containers out of the car take it all out I told the owner I was gonna get this car smelling great before he left the shop so I told him get everything out of the car I give him a box he put everything inside the box so there's no problems with anything in the car messing up the smell so now let's get rid of the smell in the fabrics now like I said this car has a very nice fabric interior and we are smoking any type of weed or cigarettes it gets embedded in the fabric the headliner it gets embedded in the carpets a lot in the carpets the carpet absorb the smell so now we're gonna get rid of that so let's use the strawberry blast air freshener what I like to do is I like to first start the car there we go and now I come over to the a/c system I'm gonna go ahead and turn on the a/c up here on climate okay it's off right now I'm gonna turn it on and what I want to make sure is that this little max a/c light it's off right now make sure it's on and then this other button right here that says we're circulate I make sure that's on - so we turn of both on this things like on also turn the fan all the way up and I turn the temp all the way down as far as it can go okay it's on low as far as it can go right now so now I'm gonna take my strawberry blast air freshener I'm gonna turn this on my spray and what I'm gonna do is let's go down to the bottom right here this is the trick I'm gonna spray it on the carpet itself so it's prime the sprayer there we go Wow this is already smelling amazing now if you see this baton right here coming close guys this vent right here is actually the intake vent it actually sucks in all of the air to recirculate the system what I'm gonna do is I'm gonna spray this right around there just like I want to spray like three four sprays there we go that just sucking up in there and then come back up here this is the most amazing thing the air coming out of this vent it smells amazing like fresh strawberries I'm gonna do it on this side to give me a second there we go that's smelling amazing yeah it's working through this is amazing this car smell like stupid nasty weed I love this car is a hundred and twenty-one thousand miles on it and it's it's probably had a lot of nasty stuff in here I know the person that owns this car likes to do weird stuff like go to Burning Man so it smells like nasty junk it smells like weed it smells like cigarettes and nasty dirty hippies so this stuff is really getting it done plus is if you're a hippie this is safe for you this is organic strawberry scent so it really does smell amazing now I like to let the a/c work for a few minutes I'm actually going to come back here check this out guys I'm gonna spray some in the back a little bit there we go and if you like you can spray this on the seat - I'm gonna go and spray this in the seat you guys can watch this real quick okay there's a beautiful products it doesn't affect the fabric it just sprays on the seat and now it's ready to go if you have this on leather don't spray it on leather but this is a nice cloth seat and it really does stink I mean but passenger was probably like smoking blunts and joints or bong rips or dads whatever but they were smoking right here you can smell it now this car is already smelling good now here's what I'm gonna do all the windows are down right that the air is they been able to flow in here now here for a little while I'm gonna roll them all up okay the dirtiest windows this is disgusting right we'll fix that later for the customer but I'm gonna roll up all the windows and I'm gonna go ahead and spray a few more sprays down here right I'll spray a few more sprays I'm gonna go ahead and spray it under the seat spray it on this side as well okay and I'm gonna go ahead and close up the car and I'm gonna let it run for about 10 minutes and let that AC run and flush out any of the nasty smells because this product has an odor eliminator inside the spray the odor eliminator attracts the odors like the marijuana scent and it really eliminates it from the system because a lot of people will run their car on the max AC and then they smoke in the car or they vape in the car and all that vapor gets stuck behind this system and it builds up bacteria this is gonna kill the bacteria instantly it's gonna smell amazing so we're gonna take a break we're gonna come back in ten minutes right after this is flushed out and we'll see the results we'll see you guys in ten minutes okay so we're back we let the car run for 10 minutes we let the AC cycle we're going to shut it off right now and there we go the car already smells so much better like I'm just gonna taking a big smell of this yeah that's a that's a beautiful strawberry scent this stuff is amazing it works so good this car literally sits outside all the time in the desert and the Sun beats on it and when you have a car that smells like weed or cigarettes the Sun just intensifies all of that smell if you have a car that smells like that when it's cool it might smell okay but when that beats on it in the summer like right we're out here in California it it's hot it's very out it's like almost an 85 degree day out here when the Sun beats on the car it starts to smell even worse but this product is gonna eliminate that smell instantly so if you have a stinky car that smells like marijuana if you're a college kid and your parents are coming home and you don't want it to smell your stinky car go ahead and get this product you can pick this up right now on our website Masterson's wax comm if you buy a used car or a new car it just smells like marijuana a lot of people might have cars like you buy a car from Colorado or California or Oregon it if it's a Volvo or a Subaru it probably is gonna smell like weed so I'm guarantee you really should buy this product pick it up on our website Masterson's whacks calm it's an amazing odor eliminator and this is the one thing that I like about this is the strawberry scent I developed this specifically to have that amazing strawberry scent strawberry scent in the car when it's an organic one just like this it smells amazing and you're gonna love it in your ride I guarantee it took over to our website Masterson's wax comm pick it up today right now for the best prices then get everything else you need to clean your interior and get your car looking right now once again if you like this video give it a thumbs up and don't forget to click that subscribe button and check out all the other videos we have right here on our channel and remember follow us on Facebook Instagram and Twitter for all the best detailing news and the best detailing products now thanks a lot for viewing I'm Greg from Masterson's car care and always remember have fun stay clean and keep on detailing now let's go do some like all wheel drive burnouts I'll see you guys next time thanks a lot guys you

Please explain how to make mini dalo style markers

all right so today um i'm going to be showing you how to make like a mini de la style marker it's not really in 3d the ink's not 3d unless you can get really thick ink and put it in um so you're going to want a big shake and squeeze their white out markers um and i got some ghetto crank it's like sort of off pink magenta-y color um yeah you're gonna want to use pliers to get it open because it's unless you're hella buff or something but i already emptied mine out and opened it up already so you're going to want to take the pliers just stick it in and twist it might be the opposite way let's try that way yeah yeah it's the opposites um once you've got it open you're gonna wanna just empty out all the um whatever it's called white out and dump your ink in hold on that's not spill probably okay that's about not enough [ __ ] oh damn it but um yeah that's why you always wear gloves um and then pop your your cap thing back on that twist the other way down yeah let's test it out i gotta have a napkin i spilled all over myself um you gotta squeeze it squeeze it squeeze it squeeze the shake and squeeze um yeah it's pretty cool it's like hella fine and thin and stuff but yeah um you got yourself a pretty nice delo ghetto ass delo um don't whatever you do don't spill all over yourself like i did um yeah get a big shake and squeeze and open it up and dump out all the crap um yeah that's pretty much it uh here let me just give you something closer to see that got some grit dye box of rit dye didn't use it for graffiti so don't worry don't worry no bret dying see i wonder if it drips no this is for clean tags only um maybe if you can get it to drip maybe put some thinner ink in it well that one's dripping but yeah that's it give it a big shake and squeeze empty it out you can rack them from walmart uh staples staples has got four packs and they're hella easy to open um yeah big shaking squeeze okay peace out

Please explain how to hook up a tractor and trailer

hey today I'm going to show you how to hook up a tractor and trailer and by definition unhooking is the same way that you hook up but being that it's already unhooked I'll show you how to hook it all up me do a few descriptions this is the fifth wheel plate cover basically we don't use grease we use these little plates we put tape on them so they don't fall down then you got the fifth wheel itself and when the trailer and tractor hooked up you have to pull this which latches it open and unlocks the mouth here and allows you to pull away from the trailer then another thing that you have to do is well wakes especially with these trailers is you have to dump the airbags in order to lower the trailer onto the blocks these blocks right here are usually kept right here there's a little slot for them format for car haulers and so what you do is you unhook you pull that you unhook all your lines which you can see there and you dump the air and once you dump the air then you go and release your break and you start pulling away forward and you undo it so i'm going to show you real quick how to do that these by the way or jumper cables that way you can work the hydraulics while the truck is stationary if you don't have those that won't work so here we go like I said you have to first thing as well when you're backing up make sure the truck has air so here we go alright so there you see we have no air what we usually do you bring it up about right at about a thousand and you can extra set the cruise which happens to be here that way you can take your foot off the gas and i'll have to sit here and just wait for the here to go up once we get this then there is a switch right here before dumping the air bags in the back once we build up here we know we're good the brakes work we're all ready I'll go ahead and hit this and start backing up and it will go right into some right into the spot all right here we go I'm going to go ahead and hook up alright so there you go then you got your obviously this is red and you guys this one which is your blue you got your electrical connections and then your hydraulic connections obviously there's your hydraulic connections electrical you're blue in your red airline hook them up and then I just completed the airbag so as you can see now I can pull this out but one of the things when you back up that you want to once you feel it click you want to pull forward and make sure it's locked and that this doesn't come out that's it that's how you hook up a trailer

Please explain how to decorate with fondant with zoë françois of zoëbakes

this is the last part of decorating with rolled fondant we have our cake perfectly smooth with the fondant and now we want to add a little bit of a winter holiday cake motif so let's do that I'm using some of the scrap that I had cut out from the bottom of my cake kit and I'm going to make little balls that will go along the bottom edge of my cake just take a little piece they don't all have to be the same size you can make them a little bit different and that'll make a nice edge as well to attach the balls to the cake I'm just going to take a clean paintbrush and dip it in some water and then just paint a tiny little dash of water right there then press my ball and then go around and the sugar in the fondant should melt to the cake so I'm just gonna paint that a little bit and then if my ball is a little dry I can paint that as well and then just go around and cover the base I've rolled my white fondant to 1/8 of an inch thick and now I'm going to cut out my snowflake shapes using a snowflake cookie cutter I'm off to decorate my this makes a really simple way to decorate with fondant is to just use a cookie cutter just like this once you've cut out your snowflakes just paint the back of it with a little more of the water to act as a glue and be sure that you know where you want this to go on your cake because once you've glued that down it's pretty difficult to get them back off without seeing it so we're all done we've put on our rolled fondant and we've colored it in a beautiful sort of wintery blue and then put on our snowflakes and on some of the snowflakes I even put edible glitter which just gives a little bit of a snow sparkle to it so enjoy your holiday cake

Please explain how to make a juicy well done steak

hey everyone today I'm gonna show you all how to make the best one of the best steaks here's what you're gonna need first thing that you will need is one rib eye this is a bone-in rib eye accent garlic powder parsley flakes salt pepper butter one crushed garlic clove and a packet of Sasol and as you can see I've already seasoned this steak very well with these seasonings okay and the red tint that you see here is the sazon packet I've just sprinkled some on both sides now the first thing that we're gonna do I want to show you how to make a butter compote in this butter I have I have three tablespoons of butter inside of this butter I have dill weed I have parsley flakes we're gonna put a little bit of salt we're gonna put a little bit of pepper all right we're gonna put some garlic powder all right what we're gonna do we're going to just mash this up and this here you can use any you can use any spices that you want to season this with okay any spices you can put chives in here alright this is what we're gonna do when this steak is done we're gonna smear this we're gonna put a dollop on the top of this steak and when it melts those flavors oh my goodness those flavors will melt down into the steak all right this butter compote done alright next thing we're gonna do I have a pan I have a saute pan we're gonna turn this pan up on medium-high alright wanna get it nice nice and hot and what we'll need we're gonna use butter alright so we're gonna put some butter in our pan here not too much let's get this butter to Sizzlin and we'll be right okay this was about one tablespoon of butter and what you want to do is you want to wait till that butter gets nice and sizzling just like this all right you always want to make sure your butters let me wipe my stove down always want to make sure your butter is nice and bubbly this way now go ahead and lay that ribeye in and watch it work don't touch it and make sure when you season your ribeye you put a nice amount of salt in there a nice amount of pepper nice another sound so my accent and garlic powder in just a little bit of parsley all right this is very simple some people make it complicate it when they make steaks but I'm going to show you the fastest easiest way to make the perfect rib eye now what we're gonna do with that crushed garlic clove we're gonna go ahead and throw that in there and what's when it happened is this garlic clove is gonna let off a lot when I tell you a lot it's gonna let off a lot of garlic flavor into the butter so we'll just let that sit in there for a few minutes and then we'll take it out after it's done its job you don't want it to get too dark okay but just long enough to perfume our butter okay you will be able to smell the garlic and you'll be able to see the color that the garlic has to indicate that it's time to take the garlic out you can smell the perfume of this garlic all through the house so we're done with the garlic that garlic has done its job all right let's take a peep in at this beautiful ribeye you want it to be nice and brown now a good way that you can tell if your steak is well done medium rare rare this is a good technique give this technique a try you will love it if you hold your hand this way and squeeze it tight that is a well done if you loosen it up a little bit that's medium well loosen it up a little bit more that's medium okay loosen it up a lot more and that's medium rare okay so if you try that tighten your hand and keep loosening it and you'll see exactly how you want your steak because what you do is you'll touch your steak and it'll feel just like your hand just like the technique I just showed you it's a really great technique go ahead and turn this over tightened up and it made the steak curl but if you just cut a little bit of that fat right there it'll lay back down this way and as you can see you'll see the smoke but it's okay that's part of making the steak and cooking it up on high heat make sure you have your ring but you always always always cook your steak up on medium high because if you don't and you cook it at a lower temperature your steak will be gray and it just it won't turn out right oh this is beautiful this takes that a few more minutes and hey we'll be ready to go I'm gonna fill it also we're almost there and we're there this here beautiful my camera okay everyone I have the steak plate it up let's go ahead and put this beautiful compote butter with all this seasoning right smacked it on top right there guys oh and you can only imagine hmm once this starts to melt the flavor that you get oh my goodness let me get a knife and we'll cut down into this Oh beautiful all right I have a little bit of a1 sauce you have to have steak sauce on the side right you have to have steak sauce watch this guy's let's cut down into this bad boy I'm gonna show you one beautiful steak look at those guys Oh perfect mmm Oh beautiful beautiful beautiful mmm if you all enjoyed this recipe give me a thumbs up if you haven't subscribed subscribe to my channel if you know someone that would like these recipes mmm give them my information and as always god bless have a great night and thank you so much for watching this rib eye is so good right now guys I seriously wish you could taste it right now

Please explain how to tie: palomar knot

i'm going to show you how to tie the polymer knot now the polymer knot is the most versatile knot out there i use it for braided line monofilament and fluorocarbon it's an easy knot to use it's quick and it will not slip so we're going to pretend that this rope is the fishing line and this carabiner is the lure actually the eye of the lure take the fishing line and thread it through the eye pull it out quite a ways turn it around and go right back in where you came out now the lure is on a loop i pinch the one into the loop with my fingers and i hold the other end like this and with the entire loop i do the half hitch knot which is basically your shoelace knot how you start tying your shoes pull it down so it's not quite tight and then take the remaining side of the loop and put it around the lure once then it's simply just pulling it tight and that is the polymer knot

Please explain how to make specialty cocktails

hello I'm Lauren Delaney general manager of Morton's Steakhouse here at Morton's we feature many specialty cocktails but today I'm going to teach you some of those today I'm going to teach you how to use cucumber to make a refreshing cocktail hi to make our Heavenly full which is a freak foam and a fun and exciting way to top any martini hi to make a pomegranate martini and hide to make our Morton's coffee we'll go over the tools and ingredients specific for each drink with each clip however it will be necessary if you have a basic home bar kit for each of the drinks and as always if your servant are drinking alcoholic beverages remember to be responsible and use a designated driver so before we get started let me tell you a little bit about myself I've been with Morton's a snake eyes for seven years I've been in the restaurant industry for 14 years so let's get started when hi to muddle ingredients for cocktails to watch the other segments in this video series or for how-to videos on almost any other topic visit monkey-see calm

Please explain how to install a garbage disposal - step by step

in this video i'm going to show you how to change a garbage disposal it's actually pretty easy but there are a few things that can trip you up this disposal here is leaking from the bottom so it can't be fixed now normally i'd spend at least 200 on a disposal but this homeowner doesn't want to spend any more than they absolutely have to so we're getting the cheapest brand it's only one third horsepower and it's 85 dollars and with garbage disposals you really do get what you pay for a weak motor means it's not going to be able to grind up the food very well and it's going to break earlier guaranteed so here's what they give you in the box they're going to give you a drain disposal mount and i installed one of these just a few videos ago so if you want to see how to install that check out the other videos also they give you a drain elbow and a wrench which you should keep because it helps unclog jams and here's the unit itself taking a look at the inside you can see what a new one looks like probably yours looks a lot different than that okay so let's get started the first thing you're going to want to do is unplug it now if yours is hardwired to the house and you can't find a plug you're going to want to shut it off at the breaker box on this model i need to take off two screws to detach this pipe yours might just have a rubber coupling that you need to disconnect [Applause] and these fittings come off by hand you shouldn't use a wrench on these you might need one to loosen a few of them but you shouldn't use one to tighten it now some of you may have this hose some of you may not this is the hose that comes from your dishwasher and it pumps the drain water into the disposal to detach it from the sink insert a couple screwdrivers or even the wrench they give you into these slots and give it a quarter turn hold on to it because it will fall and it comes off just like that while you're here you might as well make sure these three screws are tight you don't want anything coming loose later also if you did want to replace this mount now is the time to do it again i'm going to leave this one on so i have the old one on the left and the new one on the right now i need to take the plug and attach it to the new one pop out a retaining ring then with a screwdriver or needle nose pliers pinch the tabs together and i can slip this out i cut out a lot this was actually a lot more difficult than what it looks like now this is the part where you might need a cable connector if you're going to hardwire your romex cable to the garbage disposal and they were not included with this unit the old unit doesn't have wire nuts so i need to cut the white and the black wire but i can unscrew the ground now i just attach the old plug to the new disposal and the green ground wire screws into the screw here strip the wires just over a quarter inch twist them white to white black to black and secure it with wire nuts and again the wire nuts were not included so when you buy your disposal take a look inside the box and see if it's missing any hardware that you should pick up while you're there at the store and push in the retaining ring and it's done now anytime along this project if you're going to hook this disposal up to a dishwasher you need to take out the knockout plug and that's in this hole here i'm not going to do it because i'm going to make two videos out of this one because so many people ask about knockout plugs that i decided to make it his own separate video so we're going to do that at the very end but it's more convenient to do it right now now with this pipe i'm going to remove the old rubber gasket and put on the new one then attach the flange with two screws some people like doing this later on in the installation but i like doing it now so that when i hook it up under the sink i know exactly where the pipe is pointing okay next you just lift it up and make sure these three clips are attached to the ring want to tighten it all the way so get a lot of leverage and make sure it's fully tightened you don't want it falling off in the middle of running now we can attach all these pipes back together again they all loosen by hand these plastic ones the metal ones you'll use a wrench but if they're plastic and have these wings on the nuts you just use your hands it sometimes helps to give it a little shake while you're turning it to make sure everything's tight now here's the part that's so easy to overlook it's the knockout plug down in that hole it shouldn't be plugged up there's a piece of plastic covering it now if you're going to hook up your dishwasher to the disposal this is where you do it and there's a little plastic plug inside here that needs to come out so just insert a screwdriver and give it a tap and down inside there's the plug now you can hook up your dishwasher drain hose then plug it in or turn the power back on and you should be good so again my name is adam and i hope this has been helpful to you if you have any comments or suggestions go ahead and leave them in the comment section i'll do my best to answer if you want to support me in this channel and making more videos like this i could sure use the help click the support button and again have an awesome day

Please explain how to use a toaster to light your blunt

what's up everybody should boycott go4 Gamescom go big 707 on YouTube right now I'm just hanging out here at the extended stay and I want you to use right now all that excuse me extended stay deluxe [ __ ] off the 101 and Marin and you're trying to figure out like why are we here per se well if you go back to how we was a cotton off with the CHP we got that ticket so we don't go down there tomorrow and cut off with them but [ __ ] all that man I [ __ ] around and don't have a lighter so we have the blunts we had a weed in the smoking room do we keep we taught them always gonna do it so don't get the hating Matt let me show you which you can use around there you go late night I'm going to show you what you can use around your little hotel here to use to light your blunt all right now you could say that I would use this but you know that's just what I think this is going to take too long we're definitely not going to use that so let me show you what we are going to use here we're going to use the toaster for all my little cat out there I've been with the business and Elvis up with the swirl you know saying I'm pretty sure you don't let a few okay anyway we're gonna talk about it later so we going to come over check it out figure out which is a plug right okay come over here plug it in a preacher switch it up flip it around chorus this angle goes what I want to BAM now before you get to sticking your blunt in the toaster you need to press a disclaimer you need to push down on it first and check out where the [ __ ] is going to get hot and if you get hot at all if you look in there you will see the hotter lines now here is the game at task your job no excuse me your mission if you choose to accept it is to take your swish your sweet blunt OG Kush and stick it in there and not get burned all right let's go okay so I'm gonna try to go like little hide in the face cut this [ __ ] off cut it off we set place on 5 and on anyway I'm sorry so that's how you can go ahead and use your toaster they get Dan as you see that you wait you're gonna need a bit way back that was that that's not extended say deluxe man I got everywhere issue boy NatGeo for grammar calm go big 707 on YouTube shelling you eco-friendly ways to light your blunt in locations when you do that have your lighter so and if you're a hater this is exactly where we are working off you know see that little sign by san quintin we're just lightened up so you know if you got homies you know this is a great night for a jailbreak we're right here oh yeah let's keep it real my cats on base I your side what's up keep it real Alex got later on though a [ __ ] man muhfucka raise up I like that watching some Dexter

Please explain how to use a sharpening steel - herbivoracious

alright so people often ask me how to use a sharpening steel you've probably got one of these in your kitchen e that came with a knife saturday bought one when I keep your knife sharp but you probably don't know exactly how to use it well before I show you how to use it let me show you what you're trying to do so imagine that the edge of this piece of paper is the edge of your knife well you bang it go already bang it on food and eventually the edge of it gets pinto like this so it creates almost like a burr it's not that metal has been removed but it's just all folded over and you sort by bringing it along the edge of the steel you're straightening that back out so it's not that you're kind of remove material like you would when you're actually sharpening with a stone we try to do this Jess get that edge nice and smooth again so once you understand that it's pretty easy to do I'll show you a couple ways this is a partly the safer way take your steel hold it down the board on the towel the first of the critical thing is to find the right angle so it's usually about 20 degrees and the easiest way to see that ok here's 90 here's 45 by half is 25 and a little bit more 20 so that's your feeling you can also just sort of feel the original edge of the knife put it on their source it and you don't have to be a celebrity chef you don't have to do this a million lausanne just gonna do few strokes on each time and that's it you've straighten the edge of the knife back out let's see if it actually work when I should be nice and sharp now yes that's sharp let's razor sharp edges and I what you're looking for now if you don't want to do it that way you can also add steel in your hand and bring it right towards these same idea feel that angle pitch just want to be careful not to pull it in your hand or abdomen because then it's a trip to the emergency everybody sounds but this guard here's there to help that's it you can also if you want there's another kind of steel that is actually a little bit different this one is made of ceramic stone you're our sharpening and I've not just lining up the edge but used the exact same way so it sort of grind off that fold over instead of flying it up but the results of the same nice shortener do that regularly in the kitchen you won't have to take it in to be professional shopper Mueller that often so my name is Michael Mackin my website is a reverberation scom come by and visit and you can also get my cookbook from Harvard common press you

Please explain how to bleed brakes using snap on tools vacuum/pressure brake bleeder/bleeding

okay I'm going to do a quick demonstration on the snap-on Blue Point power bleeder it's a one-man brake bleeder in my opinion it's the best method to bleed brakes it's quick it's clean does a really good job of either bleeding breaks bleeding clutches or totally flushing your entire brake system if you wanted to do a fluid change this one is Blue Point snap-on other manufacturers do make them I believe mityvac is one of them I wouldn't get a cheap one this is a little expensive this one was but it's made in Sweden really heavy-duty it has an opera operating pressure up 275 psi for bigger jobs it's got a drain valve here to drain your old fluid it comes with various adapters comes with a straw that you can evacuate the master cylinder for me B so basically what you want to do is make sure the top is screwed on tight I have four cars they do about a hundred psi of shop air this is the boot we're gonna use here and we're just going to this has a quick disconnect on one end so you can clean it real good when you're done with it and we're just going to put that right in the tool there that locks down now I loosen this bleeder screw already you want to make sure that this is I just changed these so they're pretty simple but what I do is I keep my bleeder wrench on there and we're gonna do is just pop pop that right over and while you're doing this you want to keep an eye on the master cylinder to make sure you don't run that dry you could usually at 100 psi you could bleed for 20 30 seconds before you have to refill the master cylinder and a lot of times what I'll do is I'll just leave this running because it has a lock on the handle and as it's bleeding I can go and I can check the fluid whenever I want and add if needed so what I'm going to do is I'm going to put that over the bleeder with a wrench on the bottom okay the bleeders already loose and the first thing I'm going to do I'm going to lock this hand I'll start the air pressure then I'll open up the bleeder that way no air is gets trapped in the line and then I'm going to do the same thing when I shut it off I'm gonna close the bleeder first and then stop the shop here so I'll just give you a quick demo of that while fluid this night forward is reaching the change going fairly clean normally pretty brown and keep doing that until no more air bubbles appear that's pretty much all there is to it

Please explain how to make a secret bookcase door!

hey what is up guys my name is Zack or potato and hopefully you liked that intro if you did could you please do me a favor by leaving a like and subscribing it really helped me out but the first thing you're gonna need for this is you're gonna need a bookcase you're gonna need about well it just depends on how big you want to make your your bookcase for your hidden door and you just want to make it yourself a little entrance like this you're also going to need six sticky pistons a place one right here and you're gonna get place two right here now the next thing you're going to need to do is need to go make a wooden base for your redstone repeaters and start right here from the back the doorway has to be too high and just build like I am place your two repeaters on the back of these sticky pistons and put them down to the last notch I think that's what they call I don't know and you're gonna want to put your key redstone and stack it all the way to where I do now how this works I don't know but it's pretty awesome now let's test it out and see if it works and you can see there it works it works so we're going to need to do is place two bookcases right here and see if it keeps them and you can see that is successful now there's a little plug in doing this you have to build it away from these three little pixels right here it's some kind of bug and it won't allow the first piston right there to work if you build it facing this way so make sure that these three pixels you build away from anyways guys that's been this tutorial like I asked could you please do me a favor by subscribing and leaving a thumbs up anyways guys hope you all have a great day peace

Please explain how to use vernier calipers - watch and learn #59

hi this is mark from Long Island watch calm and welcome to another episode of watch and learn it's been a while since I released the last watch and learn generally this time of year I just don't have a lot of time in general to film and when I do film it's for promotional stuff things coming into the store new items thing's gonna be on sale obviously this is the busiest time of year but I didn't want to neglect watching 100% so today I'm going to do a quick video it's not so much on watches per se but it's on an item that I do sell in the store going to discuss briefly how to use vernier calipers and I'll show you what vernier calipers are if you don't know I think nowadays with a lot of people verniers have been supplanted by digital's and dial calipers but it's important in my opinion to know how verniers work with it you know you know they they're they date back you know many many years ago before digital's came out so I like to tell people you know you shouldn't should know how to use some of the old technology I think it's really cool alright so um what's not over and check out some of our new calipers so I want to go over discuss vernier calipers I sell two kinds and two kinds two brands of vernier calipers I sell marathon branded calipers these are them they're plastic I love plastic oh they're just marathon I only back up I'm sorry I saw I was saying I sell two and I sell another white a white pair that again inexpensive I dare I say cheap plastic calipers I sell both just because sometimes people want something this is a little bit of a nicer caliper than the white one but the white one is the one personally that I use but for my demonstration purposes I'm going to use the gray one because it provides the great color price a little more contrast for the camera so vernier calipers are very useful not just for watches you can use them dare I say or I hate to sound like a commercial but around the house you really can you have to measure anything under about six inches see there's six that goes up to her you know close to seven but your maximum is going to be six and change inches that you're going to measure but they are very accurate even though they're plastic now that's what I was saying before I prefer plastic for watches because no matter what you do you're never gonna scratch the case you know real good you know Japanese callipers German calipers they're hardened steel jaws if you even just Barrow their and they're sharp until razor blades if they're new if you barely touch the case of the watch you're going to Nick it so people do put you know cloth tape and stuff around the jaws and then obviously that provides protection so that's fine but you know why don't just use a pair of plastic calipers of course the downfall here is that while they can be used for a decent precision down to 0.05 millimeters you can see they are plastic so if you want to measure something and you know the harder you push you can kind of change the dimension with likes where as with steel calipers you cannot anyway so I said vernier and in case you don't know so this is now the watch one's going to start so as it slides there is a scale down here it goes from 0 to 0 here 0 to 9 then it goes back down to 0 and as well this is for the millimeter scale this is for the standard or inches scale these are the vernier scales they're a little bit different than the scales that are on the caliper themselves and you use these markings to measure increments finer than what is on the main scale sounds like a lot it really isn't but this is the way calipers were originally then I guess dials came out and then eventually obviously digital's came out which kind of like the courts revolution wristwatches you don't need to do much to be able to read a digital watch same thing with a digital caliper but that's why I discuss how to use these and how to measure things so the first thing that people I guess maybe don't fully understand is that this caliper can measure things let's see one two three four different methods so let's go over that and then we'll discuss how to read them so obviously most people go and stick stuff in between the jaws and they get a reading so that's one way to measure you put it between the if it's small you put it to the thin part of the jaws and if it's large like this you put it we're not looking for you know extreme accuracy you put it between the thick part of the jaws will read them in a minute lines my show you right now how to use them so that's one way this is called an exterior measurement I'm not an inspector I know there might be better terms for it but this is what I call them another thing you can do is interior measurements but this set of Jaws here you put it between the lugs and you pull and you can read off I think I'm doing I'm looking at the camera sorry you could read all off the distance between the lugs using an interior measure so interior measurement exterior measurement now there's two more and they're one of them's kind of hidden and I know a lot of people you know I think kind of gloss over them if you flip the caliper over the sliding jaw is stepped up a little bit so you can use the caliper to measure the distance between this surface that my finger is touching and this surface that the pencil is touching so between here and here as this slides now in wristwatches probably not the most useful measurement you probably don't need it all that much but where would this come in handy I'll show you exactly you have a something you need to measure and you cannot pick it up you can slide Oh see if I can do this on the camera you can slide this jaw here against the bottom of the table and then this jaw slides and then this part bottoms on here and then you can pick up the caliper we don't use a lock it because it's plastic and then and we can read you know five centimeters that is the thickness of the block or the depth and there's one more which is really used I would say four four screw holes or four depths of things that you can't get the caliper into there is a metal rod that slides out the bottom and again if I had something with a screw hole in it never mind I found something so let's say I wanted to measure obviously the different ways to measure things will say needed to measure the depth of the this interior portion you can put the caliper on top I'm going to turn around so you can see the rod right and then you push it down the rod goes down hits the table and then I can read again the measurement off the caliper it's I don't know three and a quarter centimeter or something I'm really not reading it so now let's go over how you actually read the caliper or the really important part the vernier scale so you saw me before I measured the diameter of the watch so let's do that so I measure the diameter and I read let me get a pointy stick so I'm gonna be using the millimeter scale so I read this line here is my initial measurement so it's 10 millimeters 11 12 this happens to be 13 millimeters on the nose because there's zero or just about on the nose because the zero lines up almost perfectly I for most measurements you can just interpolate like let's say I measured the case and it came out to be like that you could say okay it's like 13 and a half millimeters and again for what we're doing here measuring lugs and thicknesses and diameters that's fine I don't need any more accuracy than that but I can and that's where the vernier scale comes into play so let's let's set aside by the way that doesn't work or it might I don't know so I take that out unless you say I made I made up this fake measurement it looks like it's around 13 and a half so how do I figure out what this measurement actually is and that's what the vernier scale comes in handy I it's so cool and it's so easy what you do is you start looking at the hash marks down the line and you wait to see when a hash mark lines up exactly with the mark above it these three this one's a little bit to the left this one appears to be dead-on this one's a little bit to the right so it's this one that's a five so it's thirteen point five zero millimeters and I know it's millimeters and I know the resolution because it's it's written over here this will give me zero five millimeter accuracy it's not one point five five and you know this one a little bit different this one a little bit different this one appears to line up on the nose so let's do you know I was tooling around before and I think I was it the lugs I don't think was this at my Seiko I had sitting here every one second yeah it was my Seiko guys remember this one this was the one of the ones I did the water test on when the bubbles came out it's been sitting here it was pretty cool doesn't it it doesn't work it's got all sorts of obviously it deposits on it now but we can use it for lug measurements right so I'm going to stick it in there and I'm gonna take away the calipers and read and it looks like it's 20 actually if you look it's actually under 22 isn't it if I read where the zero is it looks like it's just shy of 22 so I'm gonna I'm just gonna assume it's going like 21.9 or something to come way down the line here and look at that there's 21.9 lines up perfectly 21.85 actually I think lines up even better so the lug width on this Seiko is twenty-one point eight five millimeters it's point one five millimeters it's it's nothing it's such a small amount that you know obviously for intents and purposes we call it twenty two but it really is 0.15 millimeters shy of 22 millimeters and all the cycles are you know just are different you know and that's tolerances of manufacturing tolerances of of everything and with the same process you know we can use this scale so we got one scale to scale three scale and four scale you read them all the same exact way and if I wanted to take the inch measurement I would do the same thing but guys the I like the metric system and engineering school we pretty much used solely the metric system I to start doing it with the quarters and 128th and stuff is it's just not intuitive but anyway so this has been marked from the long island watch comm showing you how to use old-school vernier calipers please like the video if you enjoyed it please subscribe to channel if you have not done so if you have any questions or comments please put them down below and I will be sure to address them as soon as I can thank you for watching bye bye

Please explain how to safer bitless horse riding with holistic horse trainer missy wryn

my right handsome I need you to step forward so I can get soon as I ask I release he takes that step perfect you are so perfect you are just the perfect horse in all the world alright let's step away step away from the mounting block and a1 rain stop oh nice to lose that's a nice spectrum can I love you on this side oh very good very good so I like my girth just a little bit a little bit loose I don't like a super tight girth you're a good rider your saddle will stay in place and you want to learn that balance I don't want a real tight girth how would you like to have a tight girth on here around your stomach around your chest that's no fun and oh isn't that nice see I just tucked in my body pulled in my belly button to my back and I pushed down on his brake button which is actually right back here is his brake button so when I push into that seat that automatically gets him to stop and so I squeeze with my legs forward we go hands forward to be have a loose rein I do a little neck and a little direct rain and we're going to do a little side pass to the gate don't get your bum over there there we go so I turn that neck a little bit so I can get the bum over there there we go side side sorry the missus all bitless forward we go so you can have your dressage moves you can have your dressage riding bitless just take the time and work with your horse do a half pass so I'm just using my leg using the rain a little bit to tilt Tim good boy and turn sit back and turn nice turn on the forehand very good and go so you see this all-in-one works just like a bit wood but without a piece of metal in the mouth here nice got your foot in there that's alright where'd we go good boy how call him he was about that forward so you just asked me to go forward and then pick up that energy and move it sideways okay so see how we've cut that route right there get over good job good job good boy Stefan huh watch the right knee on that tree see on the arrow that trail is so I pick up my right rein my right leg keep him off that tree good boy now allow him to have his head he needs his head to be able to run and to pull up now left ring left leg thank you don't want your knees in the trees good job brain left leg okay now we got a big hill to run here wait attaboy attaboy good job man good job nice and loose rain make sure I had enough rain to just guide him because there was that log off to the side and I needed him to shoot through that log that was cut didn't want him running into that one on the left so I made sure that it picked up that left rein left leg a little bit moved him over to the right remember horses move away from the pressure so if I pick up my left rein left leg he's gonna move away from that pressure going to the right it seems counterintuitive but once you've done it a few times in your horse response it becomes second nature so now we got this nice slippery hill so I'm gonna be leaning forward I'm gonna suck my belly button towards my back and I'm gonna lean forward on Paco and squeeze with my knees to balance myself and allow him to work his way down so I'm out of my seat just tiny my bottom is just barely touching it that way I can wiggle with it he's slippin and slidin I don't want to go through the tree so when I ask him over here atta boy atta boy crouch down a little bit more for him there you go there you go good job Paco good job so I'm out of my seat just standing in my stirrups bent knees crouched body oh look at the dance of the Dragons whoa and the butterflies yes into we go let's get deeper so that you can get water but my foot yeah use my office darlin this is where the world is right I love you too bumpin my foot you're so funny I miss kits in that on the camera ah feel good on your feet wash that muck up yeah wash the muck out of the booth nice and is sufficiently fueled you need a bite or two of some grass anybody watching us something I love that mr. small the world are you ready now shall we shall we head up ready you just at the beginning you well we're just about the end of our trail training really easy as you can see you need to just work with your horse in the arena spend time on the trail lotty dine doing your side past your half pass on the trail that's gonna help you maneuver the trees your horse understands side pass and half baths you can see it doesn't take a bit to do it you don't need a bit to control your horse control is through the relationship and knowing your one rain stop and a one rain stop oh good just like that no big deal you're on a runaway horse you just pull slowly and slow them down as they're going sideways with their head I never want to pull hard cuz you flip them over you drop them so you just go slow and I've had that happen little saws are one time he got spooked and we were on a logging road and he got spooked by people that were in the in the forest with their dogs and they're yelling at their dogs it was just mayhem for them not for me little Suzy got spooked oh listen motorcycle or ATV behind us I think we got out of here just in time I think they're behind us we need to get up here and turn around turn around back up nope you're good you're good here let's just go up in here there they are okay they don't even see us yeah a TVs and a little kid all right good they're not even on our trail good job okay I wanted to capture one more thing going down over the route that I came up you gotta see this so you give your horse their head when they go down this thing I'm gonna try to tilt my helmet so that you can see standing up a little bit come on but we're gonna go down and down that route so I loosened I allow my horse's head and I'm standing in my stirrups with my knees bent good shot good job good job all right just wanted to show you that one last thing all right love y'all bye bye you

Please explain how to plasti dip your cars wheels (gold/copper)

All right so this is probably the cheapest and the easiest mod for any car I can think of plastic tip is by far the easiest way to take your old boring rims to a whole new level and the best part is you can go back to the original wheels whenever you like so without any further delays here's how the plastic tip your rims for the best result possible! (INTRO MUSIC) starting off the most important part is cleaning your rims before you start spraying most people pass it without taking the rims off and if you go that route make sure to cover all your brake discs and everything like that with a garbage bag or something like that but in this case I decided to take my wheels off so I can properly clean them and get a good even spray and if you do decide to take the wheels off this is probably gonna be the hardest part especially if you don't have any power tools but anyways once you have your wheels off if your doing that or either ways clean your rims as good as you can and use some brake dust cleaner or some multi-purpose cleaner both work fine and once you've done that rinse them with soap and water and make sure the wheels are 100% dry before we do anything else next up I'll be masking off and covering any places I don't want to get deep on so for the most part if you're doing this with the wheels on the car you can just pull the plastic from the tires when it's still wet and it does come off pretty easy or if you want to be extra safe use some wd-40 or some kind of oil on a towel and just rub that on the tires so the plastic it won't stick directly on the tires but make sure you don't get any oil on your rims so once you're all set we're ready for a first base coat now I'm going for a copper finish but I can't just start spraying copper on silver rims so first of all I'll paint it all black and then add the copper layer on top so let's start with the first base coat of black now this cooling needs to be very very light it's supposed to be semi-transparent and this is where you might mess out especially if you're using positive for the first time so again this is my first black base coat and later on once I have it all black I'll be adding my copper metalizer to give it a finishing color now this is also my very first time and soon enough I realize taking the wheels off was a better choice for me but I'll put this out there if you have some experience with plastidip and how the spray can work so you can pretty much get an even coat without actually wheels off but if it's your very first time I recommend taking at least two wheels off get a hang of it and then you can try to spray the rest of them with the wheel still on the most important part here is not having any overspray and having the rims flat on the ground definitely helps with any run overs has the pro tip start spraying outside the rims and then move in and out because you might get a little bit of overspray every time you press the spray bottle so spray in and out so press let go press let go now you can kind of see at some overspray on my first base coat but since I had the wheels pad on the ground I didn't really have plastic dripping and the end result were pretty good so by the time I came to my total wheel I got pretty comfortable with the spray cast - it really just takes you to base coats to get a feel of the spray can and how it works now once you're done your base coat let it dry for at least 10 minutes naturally and if you had any overspray like I did it'll get better with the second coat and in fact by the time you're done you won't be able to see any imperfections as long as you don't have the paint dripping all right so about ten minutes later I started with my second coat and this is where everything falls into place a lot nicely and by this time you should have a solid hang on the spray can and make sure you get all the hard-to-reach places and hit a bit every angle possible once you've done your second coat let that dry for another 10-15 minutes and then we can move on to our third coat all right so my second coat dried up and now I'm starting with my third one now if you're just bring black this might be our last coat till you start seeing finishing results and I do recommend adding a fourth course just to make the layers a little bit thicker so it can take some small scuffs and scratches and I'll also be a lot more easier to peel off when you need to now for the most part if you're doing this right doing your fourth chord is where you should start using your third camp so if you just want to do three coats two kinds of plastidip should be enough to get four wheels done but it's important adding a fourth coil otherwise they'll be a pain taking it off when it starts coming out in little small pieces so for me I did my four coats of black and by this time I've used two and a half cans of plastidip and now to get my finishing result I'll be using my copper metalizer and the number of course you use really depends on the type of color you want more the coats the brighter the color is gonna look so for me I dev to Coast and it kind of gave me a dark shade kind of in a brown look but later on I decided to add two more layers and I gave me a pretty bright color and it looks really good so in total and they're four coats of black four coats of copper now the only problem with plastidip is it gets pretty dirty really fast and it's really hard to clean so you'll have to use some type of brake dust cleaner or some type of multi-purpose cleaner that doesn't melt away the plastidip so whatever type of chemical you're using make sure you try it on a small sample area before you ruin your rims and after a week or two up notice plastic does lose a shine so you constantly need to clean your rims otherwise you'll start seeing the color getting darker and darker until you clean them now fresh positive I've noticed takes about two to three days to fully dry up but I will recommend using any type of pressure washer oh and anything to clean your rims at least till a week after you've done your plastidip by that time it should be rock solid and properly stick to your rims and it shouldn't go anywhere and for most part it does take up small scuffs and scratches pretty good and yeah if you did take off your rims make sure you don't put them back on or touch them for at least 24 hours let it dry let it settle up otherwise you can have the plastic peel off while you're installing the rims because it happened to me and yet guys that's how you plastidip your rims it's actually pretty easy and pretty simple and it's a very cheap way to change the color of your rims now if you liked this video let me know in a comment down below if you need any help you can ask a question I'll try to answer all questions I can and I'll have prod links to everything abused in this video in the description box down below and as always thanks for watching!

Please explain how to pack a suitcase efficiently top travel & life hacks

today to celebrate my appointment as efficiency engineer at Holiday Inn Express i'm going to show you my favorite packing tips use portable hanging shelves to save on packing time for frequent travelers these can be pre-packed for that last-minute business trip fold your shirts as quickly and efficiently as possible place a belt in the shirt to keep the collar stiff avoid unnecessary spillages in your suitcase by sealing bottles with cling film underneath the lid and avoid wash bag accidents by putting a bulldog clip over exposed razor blades keep a bulldog clip handy for tangle free and simple wire storage and always pack chargers and cables into a sunglasses case so they are easy to find if you do forget your charger the TV usually has a USB plug in if you want to listen to some music one or prop your smartphone into a mug to amplify the speaker if you need to pack a suit jacket turn it inside out and fold it like this this helps to keep it clean and prevents creases and why not use a business card instead of a luggage label I hope you've enjoyed these travel hacks safe travels and thanks for watching

Please explain how to dress windows | window close to wall with curtains

hi I'm Jane Farnum TV presenter and interior designer I'm working with Terry's fabrics to help you get the best out of your home improvements in this series of short videos we aim to take the issues our customers tell us that they're having with decorating and DIY and provide easy-to-follow helpful solutions you windows positioned in this way are often the result of a room being partitioned leaving a window off-center you can keep things very simple with a single blind or a blind with a pelmet for a more tailored look or alternatively emphasize the asymmetry and go for a single curtain with a strongly decorative heading and chunky tie-back let's look at a few options emphasize the asymmetry of the window and go for a single curtain possibly with the decorative heading pulled back against the wall with a tie back and balanced with a chunky tie back or tassel looped over the open end of the pole a slim column of fabric to one side of the window can be achieved with eyelet heading the look is sleek and contemporary and has the added bonus that islet headings push back well needing much less stack back area than gathered headings the curtain can therefore be pushed well back off the window without the need for a tie back to hold it in position curtains in pairs are an option if you keep two light weight or sheer fabrics to reduce the bulk of fabric sitting at either side of the window when the curtains are open here unlined Voyles on a simple gathered heading have been used on a pole here the same sheer curtains are topped with a box pelmet this would need to be covered in an opaque fabric but would provide the opportunity to add color texture or pattern to match your decor and other furnishings the pelmet can be embellished with a shape if desired but when using shears and Voyles be mindful of the fact that whilst they will provide some light filtration and some protection they will not provide you with an adequate level of privacy to achieve this consider layering the window treatments and adding a suitable blind either inside or outside the recess but behind the curtains and pelmet a variation on this idea is to install a blind outside the recess to provide function and privacy and then to dress it with an informal scarf scarf says simple lengths of fabric pleated along their length concertina style and offered over drapery hooks bosses or pigs entails to create an informal looking swagga fabric that falls into soft folds at the side of the window offsetting the scarf on this style of window so that there is a long the length of fabric to one side of the window than the other would be particularly effective as it will only serve to exaggerate the asymmetry of the window which is an aesthetically desirable effect well I hope you found this video useful there are more guides and lots more information on the terry's fabrics website and if you're looking for inspiration try clicking on the on trend section where you'll find lots of useful tips and advice from seasonal fashions to useful products

Please explain how to install duraceramic tile

hi there today we're going to be installing door ceramic tile tourists random tile is a vinyl alternative to ceramic tile ok first thing we do is we took out all the appliances there's a washer/dryer here and took out the utility sink and we took all the quarter round up from around the edges now one thing that really separates a good job from a so-so job its undercutting the door jambs set your tile fits nicely underneath the door jamb giving it a nice finish so we're going to use our undercut saw which if you're just doing this spend a lot of my 400 cut so you just get a little hand undercut soft for about $10 your local box store make sure you always put your high guards on there you go all right okay next step very important step you need to get this floor clean said the glue will stick to it one game bumps in it but would use it on horsehair brush we'll start from the corner and sweep towards the door all right we'll be back in a minute okay now we're gonna figure out or layout for the tile we measured the length of the tile with the grout line it's about 15 and 3/4 so we're gonna come off the wall we measured across here and three tiles are gonna fit inside of this wall right here so that would make it look nice and neat over here there's going to be a piece in the back that's gonna be about a little bit more than half the tile which isn't going to matter cuz it's gonna be underneath the washer/dryer and in the back of the closet so when we look in the room we see a nice straight row of tile so we're gonna measure off this wall we're gonna leave about an eighth of an inch an hour 15 and 3/4 and make a mark and we're coming down here sock line measure from the front of this from the store way to the back wall and we got lucky exact tiles will fit across here but we're gonna have to start right here just barely past this line which if we put a piece of tack strip and a team in a track right here we'll be able to get our team Oldham to cover the edge of the carpet and the edge of the tile okay okay we talked to mine now we're getting ready to glue the floor we're gonna use this door ceramic D s $100 said adhesive which is made by Congo Liam and that way we don't have to worry about any manufacturer claims not working out if something happens music recommend a trowel this is 1/32 of an inch we'll start with the rim the entire rim we're gonna have to let it set for about an hour before so the glue is tacky and before we start laying our tiles okay we've let our glue set for about an hour's tacky he's not coming off our picker so we're ready fine our line start our first item and our mark here here right next up reason about eight inches of a space we could use spacers usually on your side okay do all our field tiles and then we'll do our cuts around the sides alright now we're going to do our cuts will use we'll take a top lay it on top of another tile take a no top put it on top of this tile let's pull away from the wall a little bit give a little space for a grout joint take your knife score it break it our time place around will cover all right we'll be back in a minute okay now we're gonna grab the floor one thing with this uh this is the graph that we use especially for the door ceramic the thing about this grout is you want to just you don't want to use it like a regular grout that you use on ceramic tile floors you want to get it just as much as you can right in the joints and not on the rest of the tile so I'm using this little paddle the reason you don't want to get it on the rest of the tile is because it is a bare clean up okay I'm gonna take a sponge go across it again take my sponge got a nice clean bucket of water just clean the tile around it try not take any out of the grooves okay we'll be back okay got the same hook back up washer and dryer in place our floors are all grounded cord around this up doors are home we've got to finish the job want to say thanks and have fun with your floors

Please explain how to clean your makeup sponge

hey guys so today I'm going to show you how to clean your makeup sponge so I don't use a Beauty Blender I never have this is the Real Techniques makeup sponge I've heard mixed reviews because some people like the Beauty Blender way better some people like this way better all I know is it's cheap and I think it's awesome but this goes for any makeup sponge this one is not clean you can probably tell that um I just used it I always clean my makeup sponge either right after using it or right before using it usually right before because you have to get it wet anyway and what I use for that is a bar so this is honestly the best thing I just like get it wet you know soak it make sure that it's soaked and just kind of like rub it against it and like work it into the sponge and squeeze it in and out and then you know just you watch the stuff come out it cuts the makeup so well the only problem with that is after doing after like a week straight of cleaning it cuz I clean it every single day I don't just like get it wet I always clean the makeup out I think that my makeup lays better when I do that you tend to get a little bit of soap build up in the sponge it starts to feel kind of waxy and and hard it's not like super soft so when that starts to happen I like to wash it with soap this is meant to cut grease so I will go in with this and kind of do the same process the reason that I don't use this all the time is because when I use this on like a daily basis I feel like these soap it's stuck the inside of the sponge and I can feel it you know like I have to feel it in the center and no matter how much I wash it I can't get it out so I found a solution to that as well so I'll go in with the dish soap like what I'll do this like once a week go in with the dish soap and clean it out with that as best I can and I'll be able to feel like okay there's still stuff in then I will soak it for like a couple hours in apple cider vinegar regular vinegar works well I was using that until I used this a couple days ago like a regular white vinegar Swayze Burks it's like you get like a huge jug like four bucks or something and this is significantly more expensive than that much smaller but the vinegar cuts literally cuts everything it's such an app it's such an amazing natural cleaner so I like to soak it the great thing about apple cider vinegar is that it's a natural conditioner so it's not going to dry out your Beautyblender or your makeup sponge it's not gonna like it cuts all of that like anything that is left over from the soap it gets rid of it so after cleaning it with the dish soap we'll go in with this and I'll kinda like squeeze it squeeze it out and soak it for like a couple hours I mean you don't have to do it that long you can just rinse it with this stuff I find that you can just like rinse it with it with the white vinegar I tend to soak it for at least a couple hours and then after I'm done soaking it I will go back in with this now it seems like such a process I'll go back in with a bar of soap and do the same thing just clean out like the vinegar because you don't really want to have been a gardener like left over in your sponge and it literally feels so soft and fluffy like it feels like a brand new sponge so this is just something that I've kind of like through trial and error I've found works and I just wanted to share it with you guys cuz I know you know they sell all these like really expensive like Beautyblender cleaners or makeup sponge cleaners or brush cleaners or all this stuff and it's like you really don't need to do that like I said you don't even spend the money on the apple cider vinegar you can get like a big jug of white vinegar that works just as well not quite I mean I like this butter I think it works like really well but the white vinegar you know you don't have to get the stuff so barb soap dish soap and vinegar like who doesn't have that in their house already yeah so I just wanted to give you guys that quick tip because I thought that it would be helpful I definitely was really happy when I figured it out for myself if you guys know of any other ways or like if you have a bar of soap that you just think is like badass and like cleans your Beauty Blender like crazy if you want to see you like more of these quick tip kind of videos um let me know because I can do them I have some ideas so I really just put them up anyway they're gonna be alright guys thanks for watching and I'll see you soon that's disgusting don't put that in there stop it stop it stop it stop right outside please

Please explain how to replace hot tub filters

hey this is Rob your spa man and on today's segment we're going to be talking about hot tub filters up two filters are going to need to be replaced on a regular basis now how long that is is going to depend a little bit on how much you use your spa we're going to go by regular use two or three times a week should be able to get twelve months out of your filter when talking about filter replacement it's very helpful to know the brand and possibly the model of your hot tub to get the proper size as you can see I've got a few laid out here from different manufacturers you can see is they can arrange anywhere from very small to very large filters let's just go talk about this one for a minute this is a full wind spa we're going to remove the floating we're first give it a few twists remove the filter and that's all there is to it now you want to pull this out about every thirty to sixty days and actually clean this filter with a filter cartridge cleaner putting it into the dishwasher rinsing it with your hose that's truly not cleaning your filter you've got to use a filter cartridge cleaner to truly just like washing your clothes you wouldn't wash your clothes without detergent other filters like the ones I have right here this is a master spa you'll have a stem that sticks up out of the filter area and a couple different filters that go over the stem and a lid this is another type of filter very similar to one we replaced here but this goes in an artesian just a different size that's all there is to this one that I've got here in my hand this is actually a pre-filter what you do with this is when you fill your spa or drain and refill you actually screw this onto a garden hose and it pre filters the water as you're filling the tub so instead of taking all that sediment out with your main focus you've already done it when you fill this is Rob your spa man and you can fix it yourself you

Please explain how to apply danish oil

hello so in my last video I showed you how easy it is to apply both linseed oil and this time I like to show you how to apply danish oil so what is danish oil well danish oil is an oil based wipe-on finish and it contains oil and other special ingredients like for example resin but ingredients remain a little bit a mystery because they won't tell what an ashishot is very easy to apply you just need the wreck or in this case some paper towels but before we get started let me read to you some safety notes Rex used for oiling must be laid out flat to dry or destroyed otherwise to make a Trier due to spontaneous combustion okay let's get started now like with every other finish the surface has to be prepared in this case I sanded the wood up to 240 grit before applying the damaged oil you have to shake the cam and now I just take it paper towel put in some Danish oil and apply it very easy just wipe it on now the first application I want the surface to be wet so that the oil really nuts the chance to soak in a penetrate into the wood okay so now that there is a good amount of oil on surface I leave it for a few minutes and then I come back with a clean rag and wipe off the excess okay so now I take a fresh paper towel and wipe off the excess and I do want to wipe off all the excess because at this stage I don't want any oil to dry on the surface so after the first application I hope you can see this in the reflection the wood is almost dry mean it looks almost dry there's no oil on the surface as only oil in the wood and that's exactly what we want allow four to eight hours between application and if you like to reuse the paper towel just put it in an airtight container for the second application we only need a little bit of the oil because this time it will not soak in so much and again I just wipe it over the surface so that everything is covered and then I'll leave it for a while and again after a few minutes we want to wipe off the excess oil and I apply another coat so for forth application I like to use 600 grit sandpaper a little bit of damage oil and then I sent with the oil and when it does it creates a slurry of wood dust and damaged oil and this actually makes the wood surface lot smoother I'm going to take a fresh paper towel and I wipe off the excess and as usually I let it dry for about four to eight hours now if you like a satin finish you can actually stop right there because it really looks nice but I like to put on a few more thin coats and again working off the excess you well and there you have it and as you can see damage I'll finish is very easy to apply just coat the surface with enough oil wipe it off after a few minutes and repeat this process several times until you are satisfied with result so thank you for watching see you next time

Please explain how to use - how to use fire hd 10 tablet guide, tutorial, basics

welcome back today's gonna be a basic user guide on how to use an Amazon fire tablet if you're a more advanced user you might not get a whole lot out of this particular tutorial gonna touch on the main functions of this device and some of the most common applications that you have access to so starting off here how do you use this device in terms of scrolling around and finding what you're looking for it's gonna be very similar to what you have on a smartphone device at this day and age most people have probably used a touchscreen particularly with their smartphone so you can just drag your finger up and down to move through the pages and also left and right to scroll between the different tabs in terms of those different tabs you can see up here at the top of the screen you have home books video games shop apps music all this other stuff really you are only gonna need the home page for all intents and purposes I've been using this device for quite a while and I rarely ever go into those other tabs because on your home page you have all of your applications listed out very nice and easy to see you just click on the application you want to use and then you just go ahead and use it so again you don't really need to use those other tabs perhaps once you get a little bit more comfortable with the device then you want to explore those different tabs you can go ahead and do that but again the home page is gonna be your main hub and where you're at most of the time when you're using this device to find the different content that you want to access so the next thing I want to talk about are the functionality of these three buttons at the bottom of the screen you have a triangle pointing to the left a circle in the middle as well as a square over there on the right the triangle pointing to the left is going to be the back button it's going to get you to the previous page that you were on and you can click on multiple times to move back multiple pages the circle in the middle is going to get you to the page that I'm currently on the home page so if you ever find yourself lost or you're just wanting to get back to the home page go ahead and click that circle in the middle and it's gonna take you right back here to the home page and then the square over on the right-hand side if we click on that it's going to open up all of the apps that I've been using on the device find whatever app you want to go to and just click on it I'll click on my silk browser here and then it's going to open it up and again to get back to the home screen just click little circle there in the middle all right the next thing I want to talk about is being connected to the Internet that's very important in terms of using these different applications so if you look up in the right-hand corner you can see there's a clock over on the right hand side and then how much battery power you have left and then next to that is going to be your wireless internet connection I'm currently at full bars so I have a really solid inter internet connection to my router to make sure that you're connected to your specific router you just put your finger up at the top of the screen and drag down that's gonna bring down this quick settings option you can see Frontier 22 is the name of my router and I'm connected to that if you just want to click on that if you're not connected obviously and see all the different wireless routers in your area if you don't see your router come up on this screen you can also just click more settings and that will bring up all of the wireless routers in your area find your specific wireless router click on it type in your password click connect and that should connect you up to the Internet and once you're connected to the internet now you have access to all the main functions of your fire tablet so I have a list here of different applications that I just want to touch on as being the most important to use and to start off here if you want a web browser going to youtube.com facebook.com reddit.com google.com wherever you want to go on the internet you're going to just click that silk browser here and once you click the silk browser it's going to take you to your browser options and up in the top bar you just go ahead and type in either a web address like youtube.com or you can use it as a search engine just type in YouTube and then over on the right-hand side of the screen you can see a little orange arrow with a circle around it just tap on that and that's gonna take you through Bing search for YouTube and then obviously youtube.com is the first option there so you just click on that to utilize that particular website and again you can use this with any different website that you want to go to very simple stuff so now we're going to go back to the home page so we're going to click on that circle button the next thing I want to talk about is utilizing the Amazon Appstore it's kind of like the Google Play Store but specifically made for Amazon it's going to be this little icon right here and once we click on the App Store it's going to take us to the app shop most apps that you're going to use are free to download and use there's a bunch of different categories up in the upper right hand corner there's a little magnifying glass that's gonna be your search if you want to search for a specific application so let's say we want to look for reddit so we just start typing reddit and it shows up right there we click on it and it'll take us to the reddit installation page I've already installed reddit so it says open there instead of get if you haven't installed the app it'll say get where it currently says open on my screen over on the right-hand side now I'm gonna go back to the homepage of the app store and then in the upper left hand corner you see those three horizontal bars you click on that and it'll show you your different settings for the app store we don't really need to worry about that at this point going over to categories which is on the left hand side there just click on categories and then it's going to show you all the different application categories that you can search through so let's say we want to look through music and audio and then it's gonna pop up the most common downloaded music application so Pandora Spotify iHeartRadio all these different things let's say you want to install Spotify music you just click on that and then you could get over there on the right hand side of the screen and that will download Spotify music and then you might be wondering well where does it go on my device after I install it so we'll go back to the home screen and then you're gonna want to scroll down to the bottom of your home screen and whatever application you downloaded more most recently is going to show up at the end of this list here on your home page alright so that's how you use the app store again very important to learn your way around the App Store because that's where you're going to be able to download all the different content that you might want to access things like Netflix different games magazines books songs music all that other stuff you're gonna find in the App Store the next thing I want to touch on is email you can set up email on your fire tablet and I use the outlook application which I'll drag around the screen here you don't have to use outlook you're gonna have to download that in the App Store Amazon also gives you their dedicated email application right here that I'm moving around on the screen if you just want to launch that you can and then just enter in the email address that you want to sync up with your fire tablet and just go through that particular process of setting up your email account I'm gonna go back to the home page another thing that you can do depending on which fire tablet that you get you can take pictures as well as record video I have that function on the fire HD 10 which is the particular tablet that I'm using you can see this camera option right here it's not a very good camera at least it gives you the option this is a pretty budget-friendly tablet so I don't expect it to be great quality but if you want to take pictures then you just go ahead and click camera and then if you want to shop on Amazon you can do that by going down here to where you have your little shop Amazon icon and when you click on that it's just gonna be like shopping at amazon.com for the most part you can just go ahead and search for whatever you're looking for and purchase items through that Amazon shop application and then the last thing I want to talk about with this device in terms of its main functionality is being able to use Alexa voice now depending on what tablet you get you might not have access to Alexa but again if you do have one that's enabled with Alexa we're gonna drag down the quick settings here from the top of the screen and you can see that Alexa hands-free option there I currently have it turned off if you have it turned off it's just gonna save you a little bit of battery but you can have it on it's not going to drain too much of your battery and it's kind of nice to have then you can just say the Alexa command and then it'll listen to whatever you want to ask maybe you want to know what the weather is what the time is maybe you want to set a timer you know any random thing that you want to ask you like who was the for president in the United States which country has the largest population I mean you can really ask it whatever you want in it for the most part we'll be able to respond to whatever questions that you have so if you want to turn on Alexa hands-free you just tap on that icon and then it'll show you that it's on if we go back to the home page with Alexa on when you say Alexa name you can see it'll show up with that blue screen line across the bottom and then it's listening to whatever you want to ask it and if you want it to stop listening you just say stop and then it'll turn off and again you can ask it a bunch of different questions I went over a handful of things that you can ask about it's really convenient and nice in terms of just getting simple answers to things that you might have questions about so that's pretty much gonna wrap up this video guys i touched on web browsing how to use the app store the email option you have you have a camera you can shop on the amazon shop you can set up alexa and it's just an endless number of different things that you can do on these fire tablets as you can see on my screen i have a whole bunch of different things that i've downloaded here that i use and have access to and i have a bunch of different videos on how you can go about using some of the different functions on this device that perhaps I didn't touch in this video so thanks for stopping on in subscribe for more and I hope to see you guys back here for future videos

Please explain how to make a fall trellis/topiary

hello in this episode we're going to learn how to make a topiary such as this which is perfect for an entryway on the outside of your door or for your or any other corner where you might want some height and just some fall decor this is very easy to do and you I'm going to show you how you can switch it out so that it's not permanent for that season you can use from season to season so now one of the first things we're going to start with we have our container and we have our topiary now I already have this foamed in for doing on your own at the house just choose the container that you want that fits your topiary frame you can use either the floral foam blocks and fill your container with it or you can use the triple expanding spray foam that you get in the can at any of the big package stores or any craft store if you're using the triple expanding foam it can take one to two cans to fill a container of this size just depending on the weather conditions as to me how much it's going to expand if you do that have some Moss ready so once you spray your container and that foam starts expanding that you can immediately lay the phone or the moss on top of your phone and press down and keep it somewhat corralled into your container and not get them all over your hands now once you've got your frame stuck down into your phone then you're ready to start decorating one of the least expensive for the money things that you have this great fun so get you an inexpensive grapevine wreath and unwind it now this gives you great textures I said it's one of the least expensive things that you can get to give you bang for your buck and locate the end and start at the top and you're going to tie this off just in random places as you spiral it around now today I'm going to use what's called a barked wire there's bark literally wrapped around this wire and I'm going to use it just because it ties in you can use regular florist wire you can use a must wire such as this just an anything that's going to blend in in this case you don't want to use chenille stems because those will show up so we're just going to cut a length off just a few inches long and we're going to start with this end as I said we're going to start up top and we're just going to tie around the finial now if one breaks like the just did here don't worry about that at all because that's just going to tie right in now I'm going to loop this around and I'm going to tie that tightly and I'll leave those in sticking out there okay and then just start working with your grapevine at that point and just start wrapping now this in general is easier to you to do on the floor of course unless you're a giant and can easily reach up let's get this going around here well this whole thing is spiraling okay now let's take our first tie right here where this one's broken and that's going to hold that end down I'm going to cut off another few inches all this is doing is starting you're spiraling wine and again giving you texture there isn't another end we're going to tie that right in with this one and we're going to keep working our spiral around and as new ends come up also add those in okay let's pull that on around bring this down and now that i'm down at the bottom i'm just going to snap this and then i can lay the rest of that aside now if you want your grapevine thicker you can go and do another row it's just literally up to you the technique is all the same I'm going to tie off the bottom and I'll cut this short end here I'm going to tie that and this one other edge that's sticking out I'm going to pull that in and tie it okay next is mesh I have a role of the 10 inch or inch mesh going you can use any color you like of course depending on the season also depending on your decor and with that i'm going to start spiraling it around in a different location from my great bond because i want layers i don't want one over the other and one thing to be hiding my previous work so i'm just going to tie that in and I've left longer tails on this lower tie so that we can attach a bow in a moment okay now then i'm going to start wrapping and let's see we'll keep this first time every low just pinch in gather in so that you get some nice body going with your ribbon and secure that and keep moving up the piece let that puff out around your grapevine and just spiral on up anywhere that you think looks right we'll do one more about right here and then I'll move up to the top now once you reach the top and we're going to cut pretty good length here because pull this through and bring it on up and we're going to form one loop at the top just to give you a little more going on and finish off the piece and then we're going to tie that as well and that has your mesh layer going now you could also use the 21 inch ribbon as opposed to the 10 inch that I've used it will just give you more fullness if you want more coverage over your frame maybe if you've got a plane frame so there's no design work going on you might want more coverage otherwise I would stick with the 10 inch now then next I'm using a burlap ribbon which has got varying fall colors woven in with it and I'm going to do the same thing first I'm going to trim that flat edge off so that my ribbon comes to a point and I'm going to use my previous ties and tie that with the mesh now of course i'm using a narrower ribbon here and that way as i bring the burlap along I've got the orange mess showing out on each side of it and so that just gives me that layered look it doesn't hide anything really but it does work to give me just that one more layer of interest just kind of let it loosely wind along and work with the mesh on living along ok and then once again I'm going to bring that through up make a loop n in and tie it off beside the other piece so now you can see as I turn the piece how you've got interest going on all sides now next would be the bow we have a video showing how to tie a bow but we'll just kind of review that process first off you're going to roll out and you're going to leave a tail the link that you might want hanging down remember the mash curls some so you can go a little more if you need to because it is going to curl up and you're just going to pinch all of this up in your hands do one half twist so that you keep that bow loop going and we're going to gather that in and grip it and turn our ribbon one half twist the reason I'm doing the one half twist with this is not because I've just got one good side of my mash because it's the same on both sides but because of the role of the ribbon itself the body helps keep my loops fully strong now you can stop off at two loops particularly if you're having trouble with this but only i would go ahead and do three and that's what i'm going to do here and I'm going to gather in and I'm going to cut now remember with mesh always just cut straight across don't do it on an angle because the mesh ends will Ravel out you want the least amount of edge showing for that now then at this point I can take one of the ties tie this off and go ahead and attach or as you get more and more used to it and building your bows you can stack in with the next color and continue on so that's what I'm going to show you here i'm still gripping this between my index finger and my thumb and i just work that into that bend of my hand do that half twist because of course in this case there is a backside of the burlap because of the seemed edges i'm going to do that half twist again gather into the my hand where I can hold it and do my final third loop gather in and then I'm ready to cut where's the burlap i am doing on an angle because i don't care if the ends of that fray now I've got my ties here already from the previous bit so all I'm going to do is hold this place it in to the center of those ties and pull those tight and twist them in then I'm ready to just fluff out my bow a bit till I get the result that I'm right now there is my bow fully attached now at this point I'm going to move around to the front of the table and we'll discuss putting the decor on now we're going to work off this and show you how to work your decor I haven't glued anything in here because of course fall is a short season and I want to reuse my topiary from season to season and switch it out so what I've done first off is I have a fall pick this one with a pumpkin so it gives me nice visual weight and I don't have to add anything else to it or glue anything in at this point so I've just shaped that out I've used two of them I took one in here and I took one into my thumb on this side and just insert it like so that way you know my pumpkin everything is showing up now I want a bit more volume going at the base so i have used these grass bushes and I just shaped those out of course everything is wired on the blooms of the grass itself so i fanned those out because i think about where i'm going to place and how they're going to be I go ahead and fan all over that out and use again the entire Bush no cutting and then insert into place wherever I want it to go into the phone now if you're using well it doesn't really matter what kind of phone you're using sometimes there are hard spots so one of the easy tricks to use before inserting in is merely to take your heavy scissors and jam the point in just give it a quarter twist and that opens up a space for you to insert your bush into without you having to push and shove and and all of that so I've got one bush here we've got two bushes of grass on this side and so that's got my bass cover now I need a little more interest going up through here because wherever you've got this time that's kind of narrow and uninteresting so I've mixed pine cones I've mixed pods and you can get the boxes of the vase filler you use the different orbs depending on what colors you want going on what interest you want to go and then take the rest of it and put it a bowl or using some of your other seasonal arrangements but I've glued those in place either using your hot glue gun or the glue pan now one trick here is to make sure when you're gluing only glue to your ribbon and your mesh not to your frame that way you can untwist the wire at the end of the season roll this up loosely place it in a box or bag and store it away until next year when you're ready to put it back on you already have these then marking where you tie it back onto your frame at so it makes it very simple to do you can leave the grapevine on from season to season no problem there and mix the rest of it in then after that whether you want it lit or not you can add the battery pack lights which are the small wire lights that we have also very easy to store and in the battery pack those of course you can just wrap an unwrap their very thin wires was just that glue bead on the wire itself forming the bulb and just spiral that down through the pace tuck your battery pack in among the bow and that gives you easy access to the on and off and these of course last you two or three weeks of constant burning before you have to switch the bulbs out again so even if you left it on all the time you know a couple of bulb changes is all it would take for your fall season and there you have it your completed topiary all ready to make your entryway or any other area in your home very holiday filled and classy you can get it all at 36

Please explain how to make leaf print holiday wrapping paper

bono klein and her sister zeba klein my friend parveen's daughters are busy making holiday wrapping papers this is a very nice technique all you need are some pressed leaves and some craft paper and peeled crayons we have an assortment here of dried and pressed leaves these are leaves that have fallen from the trees and are pressed in the pages either of a phone book or in a real leaf press this is a fig do you know what this leaf is magnolia you do know what this leaf is maple maple this is the dog and this is a beautiful beech tree it's an unusual beach but all of these with the veining on the back and you use it wrong side up and you place your leaf wherever you want and you just rub with your crayon the veining picks up the brightness and the outline of the actual leaf you can do repeats of the same leaf or you can alternate with other leaves now what kind of names are your names girls b-a-n-o-o and z-i-b-a kind of unusual names yeah what kind of names are they they're from persia oh that's beautiful i love your names what grade are you in i'm in fourth grade and your sister fifth grade if you choose a really nice paper girls one that won't tear when you fold it will make very beautiful gift wrapping you can see all these boxes were very nicely done don't you think yeah your ferns are looking great how are your maple leaves very nice well i think you should now create a present for your dad wrap it up with your beautiful leaf wrapping paper and take it home don't you think yeah making your own wrapping paper out of dried leaves like this is a good thing it's simple and easy thanks girls you're welcome

Please explain how to measure the flue and crown of your chimney for a chimney cap

choosing a chimney cap can be an overwhelming task but fortunately determining what size the chimney cap you need it's in as difficult as it seems grab a tape measure a pencil and paper and a ladder you will need to get up on your roof to physically inspect and measure your chimney I'm Melissa from Northland Express and in this video I'll be showing you how to determine which type flute you have and which measurements you need to take before you can choose a chimney cap let's start with talking about a single flute chimney with an extended flute this is going to be the most common chimney style it also is going to be the easiest cap to measure for you're simply going to measure the width and the length of your extended flute and make sure that you're measuring the outer diameter of your extended loop a single fluke apps often mount with pressure screws and a flue size range that it will mount to for example an 8 inch by 8 inch cap will make tip flus from six and a half inches to eight and a half inches in both widths and lengths now if you've got a single flue chimney but your extended flue on the top is going to be an oval or round flue you will need to use a tap mount style cap so if your flue is oval around make sure that you're measuring the total crown width and length and the width of the area surrounding the flute as well as the height of the flue if it's extended now if you've got a chimney that's a single flue chimney but the top of your flue doesn't extend out enough for a top mount cap or it's flush with the crown you'll want to use a flue mounted cap you'll just use it should be cap like it that's going to allow it to be held in place from the inside of the flue now if you do live in a very windy condition I recommend using a top mount bracket that's going to allow it to directly attach to the crown of your chimney rather than fitting inside it will be a much sturdier connection now we are measuring for this again outer width and length of your flue and you'll have the measurements that you need and finally the last style chimney you have may have would be a multi floor chimney and if you've got a multi flue chimney this is always going to require a top mounted chimney regardless of whether they're flus are extended or not the measurements that you'll need for this kind of chimney are the total prong width and length the length of the area surrounding the flue as well as the width and the height of the tallest Blues sticking out that is to make sure that it's at least five inches taller than Tallis flew as not to interrupt a draft of your chimney multi blue caps can be sized to fit just around the flues or to cover your entire chimney crown you can save on the caps cost by sizing it to the minimum amount needed to cover just the flute especially if you're going to be choosing an expensive material like copper but for the best looking cap and the added protection of covering your entire chimney crown most people do choose a full sized cap I hope you found this information helpful if you've got questions about measuring for a chimney cap or you need assistance choosing a chimney cap please give our experts a call at eight six six six six seven eight four five four they're always happy to help

Please explain how to make tuna patties

what's going on YouTube Fox everyone doing home is doing well for 2017 so here we are at it again my kitchen on the show you guys how to make some tuna patties so this is what you're going to need you need plain yogurt Greek yogurt 2 eggs bread crumbs I'm going to go with five cans of albacore tuna in water pepper paprika pink salt black pepper olive oil or cooking spray when I grill my purple onions you don't have to drill them it's up to you or you can just cut them a small pieces almond flour purple onions and baby spinach now if you're watching sugar intake because of you know barbecues a little high in sugar then I would eliminate the barbecue sauce and just use the lemon real lemons two lemons and every wondering what that is those are actually coffee grinds I put all my plants after I'm done brewing coffee it makes plants grow a little faster it kind of fertilizers should I say so first things first I'm going to grill my onions and get that alright now check onions are cut in small little pieces next step add a little bit of olive oil or cooking spray it's up to you get the burner going and start mixing them up very well if you don't want to grill your audience you can go ahead and bypass this step just cut them small little pieces put them in a dish well the onions are being grilled next step you want to go ahead and cut your baby spinach cut them in small little pieces and if you got time as well start draining out the cans of tuna and put them in a dish right onions done nice and grill turn off the burner all right if you haven't done so yet look at that mmm put the tuna drain them out put them in a dish we're going to cut that in small little pieces I used to bought a whole full dish here of spinach so let that cool down cut the tuna small pieces Joonas drained onions are nice and cold kind of mix everything up so go ahead and put your spinach oh yeah as far as the Greek yogurt I'm going to use about half of a container instead I don't really measure my food if there's something does but I don't so I'm going to throw it left half I used to be for once upon a time and roll my food but not no more well crazy man cool two eggs crack those suckers bread crumbs Mitya said how many of you want to get tactical 1/4 cup gives you 23 grams of carbohydrates doesn't keep the corner like that is cool for now work sweet a little bit of paprika pepper wait now a little bit of pepper just a business okay something like that is good a little bit can offer too much and little bit of almond flour I'll say about half a cup to a cop we'll be fine like I said I've been doing this for such a long time I pretty much have the measurements right in my head now look sit if you're watching your sugar intake put the barbecue sauce if you're not really concerned like I said go ahead put barbecue sauce on if you're watching your sugar intake just use lemon instead so what are we going to do you know what let's go with lemon only so throw your lemon in there drain it all out and once that's done mix everything up and then we're going to make small patties with their hands now you got everything nice and mixed go ahead and get the burner going on add a little bit of olive oil or cooking spray it's up to you I added olive oil once the burners nice and warm just grab a little bit of your patties mix a little ball throw it in there now if you find it too mushy too soft go ahead and add a little bit more of the almond flour to keep it together so let me show you how it looks now me personally I don't really care if it comes out nice and pretty all I care about you know once I get to nice and grilled and toasted look at to the other side and then I put them all together in one big container I don't really care if it comes on nice and pretty but if you want it to come out nice and pretty nice little round balls amongst its add a little bit of the almond flour to keep it nice together so just get one side going on once nice and toasty look at the other one says they're a pain if I flip them sometimes it comes out great sometimes it doesn't Wow I remember using one hand come on slick there we go together perfect doesn't lose it ah at the other side they're done I just showed you what a small little patty looks like nice acidic fell apart a little bit but me personally I don't really care talking on my stomach so mink I just grabbed a freaking good roll just throw it in there it's all going to go to my stomach so I don't need to make it nice and pretty long is it nice and Grill that's all I care about and then do it in sections to about half of it I'm trying to personal body lay it all out stop burning yourself first that's it that's the other half sit here oh yeah mix it up get it nice and drilled planet out one big huge tuna patty trying to make it nice and perfect for you guys by the way I'm going to put that sign up my garage next to my Chevelle so thank you very much for watching hope you like you add subscribe add some comments if you having a good recipe you say a passing moment I try to learn too as well so my reasons why not talk of any type of supplements or training during my videos because I believe the first things first get your foundation down if you're not eating you're not growing period bottom line I mean it doesn't matter if you're genetically gifted you're training your butt off and you're taking supplements you're taking all kinds of other crap but if you're not eating the proper foods you're not going to achieve the goals you want it ain't going to happen so get your foundation on first cook right eat clean foods train your butt off minimal supplements and everything comes into play all right you guys take care until then

Please explain how to make- recipe by chef shaheen

hello friends this is shining welcome to my kitchen this is mango season but in a few days when there will be no mangoes you will have cravings for it so here is a Bank of wrapper for you prepare it and store it you this is raw mango I have grated it we get totapuri it is a quality of mango it is not very sad and murabba taste great when prepared with tota pari this is half a kg of it and this is 200 or 225 grams of sugar it depends on your liking if you want to increase add more sugar or if you want to decrease reduce the sugar we are adding right now this is very simple to make and always store it in an airtight container when it is cooled down in your fridge you can enjoy it for 2-3 months and this is white pepper powder this is red chili powder half a teaspoon of each again add according to your liking where once the sugar will melt now we are adding salt to it this is sweet answer what about you can have it with paratha stories or even with darlin rice this is sighted castle about 1/8 of it or two three pinches now the sugar has started melting cover the lid for 2-3 minutes if you are preparing it in an non-stick pan then well otherwise keep an eye over your murabba the sugar may get burn don't add water cover it for 3 minutes after 3-4 minutes I am removing the lid and I am cooking on induction cooktop if you are preparing this more about gas Lancey to it the time may differ let the syrup reduce completely and this is orange red food color it's optional if you want to add otherwise you can after cooling down it becomes a critical so I am putting off wait here's your Baba is ready cool it and store it in your fridge enjoy

Please explain how to convert 2d photos to 3d in after effects

hi guys what is up so I thought it was about time now that I should release this 2d to 3d photo tutorial and I'm going to use the same photo that I used for the actual demonstration video the little test I did and the only reason having any reason I've taken so long is I wanted to try and find another photo but actually it's quite hard to find a photo that's actually suitable for this effect as obviously you need something that can be easily content awared from its background and you'll see why when I start in this video so what we're going to do first is we're gonna separate anything that's in the foreground from the background so obviously in this photo the spider-man is in the front and the New York City skyline is in the background so I'm just going to use the quick selection tool to select spider-man now Alban advising is using the Year quick selection tool as it's not very accurate and I do prefer using the pen tool for example that and actually it's quite frustrating to use but the only reason I'm using it is because obviously I don't really have much time just sitting pen tool it and I'm sure you guys don't want to sit and watch me paint all around a character for 10 minutes so and again this tool isn't exactly time efficient um yeah so you want to just get your rough selection well um let me just sort that at the bottom there so you want to just get a selection which is roughly correct and right there we go so you want to select around this cutout spider-man here with your control and just click on the thumbnail then let's go back onto your background and go to select modify and expand and then put expand by about 5 pixels press okay then you want to right-click fill and make sure use content aware is selected then just press okay might take a little while but it will try and fill it in as correct as it can obviously it's never perfect but for the purpose of this tutorial obviously I'm not going to sit here and content-aware every little building if you want to do that yourself you can you obviously use the Spot Healing Brush or the clone stamp then what I'm gonna do just get rid of this text at the bottom here by doing exactly the same thing fill content-aware and if you're happy with how that looks I mean you that's not exactly fab but um if that's how you want it to look and by all means just do it like that um I'll just content aware that finger no in actually I'll select it put it onto this line actually put it on him and then content somewhere on this layer so it's quite a fiddly little thing I mean sooner agent second is long to come out the video really good sir I really want to need a photo which could be done quite easily and quite quickly in this tutorial so tonight once this is done you want to go to file save as and usually save as a PSD and I'll just save us spider-man make some others compatibility to make sure it's chipped click OK and we'll now head over to after-effects and I'll see you in a minute right here we are now in After Effects I don't know why I said see you in a minute it took about a second right so we need to cuz file import file and you want to select the layer and when you've selected the PSD and ask you what you want any of these selected make sure your edit book editable layer Styles edible and live a Photoshop 3d is all selected so once that's in there like that you want to open up this folder and you've got your two layers here then let's go down to your composition now I'll ask if you want a single composition I'll ask you if you want to sequence your layers make sure the sequence layers is untape and make sure everything else is how I've got it here then just press ok and you've got your image like that now of course we don't want it that size so you want to right click on your composition composition settings and change it to 1920 by 800 now 800 just gives you the black bars like a blu-ray file is 1920 by 800 and I think spider-man is on the left right yup so obviously we need to drag him back to where he was which is about there and what you can do is just drag these in a little bit because it's a bit too pip small has a bit too zoomed in and so there's a spider-man on that and I think actually he's a little bit out of place there yeah I think he was about there so maybe we'll just move that again okay and you don't want to move it around and make this area outside too small because obviously when you're adjusting the camera you don't get the black bars at the side of the screen where the pictures been cut off so it's good to use a picture which is higher than the resolution of the video you're trying to make so yeah what you want to do now is you want to make sure these 3d bits are selected so whether little cube is here if you don't have that then make sure you click on toggle switches and modes and that will come up there so now that's done you want to go to our camera view and click on top now the spider-man layer you want to bring right forward on the z-axis so now when we go back to active camera he'll actually be in front of the background by quite a lot so you want to do now is you want to go to layer new camera just click OK don't have to worry about any of these settings so just click on OK and then you can just click on the orbit camera tool here and once you just already change you're starting to be able to already see that 3d effect now see what I mean there by the black sides yeah you can avoid that by just not panning that much so just make sure nothing rides into that view section so if you want actually start messing around the camera you wanna just go into transform and make sure that all of these the timers are highlighted here so you can start adding keyframes and you can just start off by having your first shot like that and then you can have your last shot however long you want it to be stun it in about five seconds brilliant and maybe to change out the composition settings just drag these out here sorry about this guys right so and then what you can do is obviously drag it right to the end about one about five seconds and just drag it to the opposite side so you can really see that change of angle and what's going on there which looks really nice and obviously you still play around with all the different angles and stuff so I mean you could have it like that if you wanted to and really have it angling that shot and it's really up to you how you messed around the camera angles it's you know it's your project it's up to you how you do it and I mean once that's done what you can do then is close your camera down and with all of these selected just go to layer pre-compose make sure move all attributes into new composition is checked and open new composition is also checked and there you've got your pre comp there with everything done and then what you can do obviously is add any effects like looks or whatever to make this photo look a bit more well so make a bit more punchy top so you've got all these different settings here they're actually my own presets and your popular film whatever anything like that just to make the image look a bit more interested in and that's basically it and that's how the 3d image works it's just all to do with putting things on a different angle and bring them forward messing around the camera it's all personal preference it's how you want it to be done so if you don't like the way I did it in the video that's fine do it however you want to do it obviously have things down to personal preference so I hope you found this tutorial interesting and helped you to understand the effect a little bit more feel free to leave video responses with your own test if you've gone out and done it and tried to pull around with the effects yourself feel free to leave as a video response it'd be great to see what you guys come up with thanks for watching and I'll see you guys in another tutorial

Please explain how to install a sump pump

hi I'm Shannon from host improvements comm and in our video today I want to show you how to install this submersible sump pump in our in our new sump pit that we just installed in a previous video so if you haven't seen the installation of the pit you might want to check that video I'm just taking the lid off to get it out of the way basically what we've got is a is a dual pump system so the main pump that you see here is a 120 volt submersible pump I forget what it is 10 gallons an hour a minute I'm not even sure they're very a little bit so it doesn't really matter on the size so that's the the 120 volt and then right here we've got a 12-volt backup so if the power goes down this one automatically just takes over and kicks in and runs off a 12 volt battery so there's different combinations this happens to be all one unit purchased exactly like you see it everything you see right here is what was in the box so it's it's fairly user-friendly and pretty quick to set up so and actually it was fairly inexpensive as well so the main main components of this we've already talked about the pumps but over on this side we've got all the electrical requirements for the 120 volts so it just simply plugs right into the wall this here is basically a switch attached to the to the float right here for the main pump so once the float indicates it needs to turn the pump on the switch activates power and it turns them with the 120 volt pump on on this side all this wiring here is to do with the 12 volt so we've got a couple leads here that are going to hook to the battery really simple this is just kind of the information center and the charging system because this particular one does trickle charge your battery as well this wire is just the electrical hook-up from the pump to this system so really simple both pumps each have their own built in check valve so here's a check valve here check valve over here what that does is when the pump turns on pumps water out that check valve is a one-way so when the pump turns off and the water wants that's in this vertical piece of pipe wants to come back down at can't it stopped at the check valve so okay so I think I showed the floats they're both here this is the for the 120 volt and this little guy over here is for the 12 volt system so everything's right here it's all in one package nice and neat a lot of wires but we can deal with all that once we have it out of the way we're doing a bit of a temporary setup here because there's going to be some changes down the road but we're going to set it completely up so you can see you know how it's going to work basically in the hole our pits about two feet deep there's already water in it we've got some blocks sitting in the bottom just to set the pump on so that it's up off the bottom a little bit and it isn't sucking in any sand or gravel that might be down in there so I can simply lower this pump in there get it sitting on my blocks get it sitting about where I think I want it I'm just going to get my electrical stuff out of the way so we've got it sitting down there in the hole our lid has a has a slotted hole in it for all the plumbing and wiring to come up out of so that it has easy access and then once the lids on you know it's it's fairly safe kids aren't going to fall in it or whatever pets okay so again pretty simple setup I've already prepped up the plumbing so basically just is going to fit into there and over into there and then we'll adjust the pump so everything reaches nicely this is just a rubber connection so it kind of helps to make a quick disconnect if you need to but it also probably works a little bit good as an isolation setup so any vibration from the pump isn't transferring through all the plumbing as well so so I can see that this needs to slide over there just a little bit more and then we should be fine I'll maybe glue that fitting first and then I'll tighten these rubber clamps over here or these steel clamps on the rubber fitting there so actually before I do that should just talk a little bit about the couple different ways that you could drain it our system we're allowed here to pump this this pit right into the city sewer system some municipalities won't allow that so your pipe may have to come up and out and actually out the wall of the house and drain to the exterior of the home if you got that type of setup ideally you want a fair bit of pipe on the outside so the water is running away from the house quite a ways and not just going right back down to the outside of your basement into the weeping tile and back to the pit you're just recirculating so you want to get it out in a way like I said here we're we're going right into the into the public sewer system no that's a bit wet I should dry that out actually I don't have a ragging on me I've got some paper towel over here I'll just grab quick we had an old pump set up here temporarily overnight and just got a bit of residual water in that line just dry that out put some glue all the way around here stick the two together okay now there there is some strapping and stuff here on the wall to help support this pipe so that the wheat isn't just sitting solely on the pump or you don't put a block of wood under there or something to hold it up so I can tighten up these clamps for our connections okay just like that just blew out of the way so we don't have our our permanent electrical supply great clothes in handy here it said there's a bit of another renovation going on here as well so I'm just going to temporarily run this off of a extension cord so so this end I'm just going to simply plug into the cord which actually I've got here there is a little transformer here this needs to be plugged into 110 as well and then plugs into that yellow box that runs the 12 volt and this is the charging sorry the the charging apparatus for that right now today I don't have that quite ready to go yet but we will run another power bar over here just to plug that in so once you get the pump in the hole your plumbing hook together they send you a fair bit of cable here and some zip ties as well some plastic ties so we can kind of get all the electrical around the pipe here and fasten to the pipe pulled it up out of the hole just going to do that here now I get older cables make sure nothing's twisted up or kinked or anything like that just kind of bring everything up here neatly we'll put one cable tie down here just to hold things up I won't get too carried away with this I'm going to strap a couple pieces up out of the way okay so we've got that hooked up there we can actually I won't hook up to 120 just right away but what I will do is look of the battery system this this here comes also with some pieces on the back so you could zip tie it you know attach to this pipe or whatever but there's not a lot of cable on this between the yellow box and the battery connection so you need to make sure you're at least close enough to to get the connection of the battery so we've got in this case we've got a deep cycle battery it's fully charged make sure it's fully charged before you set this all up so that your trickle charger has a decent decent chance to get started with it now that audible you've probably heard that that's the sound you'll hear if the battery goes low enough this gives off a warning to let you know that it's it's actually depleted it's charged or it's no good or whatever the case may be there's a few indicators here with lights kind of gives you a visual you know everyday as you walk by or whatever just make sure that everything is working properly you can actually turn the alarm off so actually that's on there's a test button there okay so we've got that now this particular system they do have a battery backup system that you can buy or sorry the battery setup that you can buy specifically made for them and they've got a probe that would normally go you know in one of the battery cells and it sets off an alarm if the battery fluid gets too low so that you know you need to maintain your battery now when you're using anything but their recommended battery you're told to cut this lead off and actually connect it to the positive cable as well otherwise the alarm will be going off all the time so we've got that this cable has the mean connection down to the pump from that system so now before we have the 110 volt plugged in by rights I should be able to manually hit the float right now and activate the 12 volt pump now it's not going to pump water because it's actually not in the water but I'll just check it here manually I think you can probably hear that running and I can't get it off because it's not getting a crime okay so when that you know I'm just testing to make sure that pump and everything is working I just left that unplugged here for right now right back here is the charging port for that other cable but yours your system could be a little different but okay so we've checked that that float that seems to be okay it's kicking the pump in now I can plug in the 120 and again like I said I'm just using this cord for right now now this one that floats in a bit of a cage so I'm going to see if I can actually get a hold of it to manually check I kicked it on you can hear that there was barely enough water in there to run it but and there it shut off already but if we had more water in there it would actually run for however long I needed to let the float down and it'd be shutting off on its own the one thing I noticed on this one there's no real way to set your like your level of the winner when the float activates the pumps because they're kind of fixed rate to the rate to the pump setup itself so really the only way you can adjust that is by putting less or more blocks or thickness underneath the pump it doesn't really matter really how much water's below your pump it's you're more concerned about the fact that it can't fill up high enough to overflow your actual pit and in our case here our float the water level would wouldn't even come up probably 15 inches from the top here before the float comes on so so that's going to keep it well down there buys a little bit of time you know if the if the pump is having a little trouble keeping up it buys a little bit of time there too so so in our setup here all this basically goes together there's a lid that fits over here that goes on all this like I said Fitz down in the hole keeps kids and pets and that sort of thing from falling down there and you know kind of keeps it all nicely contained so again typically you want to have your electrical requirements right here for this type of setup you'd need at least two two places to plug stuff into this being such a large box and I guess they've got a setup that it would work the other plug would still fit if this is in the bottom so both the only other thing to speak a little bit about is anytime you have a battery you don't want to set it directly on concrete you want it on a block of wood or in this case we've got it in this plastic case here which actually has a lid and everything so if there's any spillage battery overheats bubbles oil over anything it's all contained in there to safely so this is probably the best setup for you is right there I think that's that's about all I can really tell you about this so pretty basic setup especially when it all comes as one unit like that really everything was there except for buying the battery outside of outside of that everything was in the box that this pump was in so so I don't think there's anything else I can tell you like I said before we we installed this sump pit so if you need to do that you might want to check that video out as well this pump is small enough it'll fit in I think up to even like a five-gallon pail if that's all the type of size you've got for diameter for your existing pump sump it this one actually will fit inside of that song which was really common for years and years a lot of people just sunk up metal or a plastic pail in the ground that's what they used so okay so I think that's it so I hope hope this helps your process and installing or doing a similar type thing and good luck with that and we've hopefully given you enough tips to you maybe help you decide what kind of pipe pump that you want we've got all kinds of other information you can check us out on youtube obviously you're there watching this you can check out our website we've got a forum there which is the best place to post any questions you have this or any other project you're doing we've got Twitter we've got Facebook there's all kinds of ways to keep connected with us we've also got a patreon account set up so if you'd like to pledge us on patreon that'd be awesome we just appreciate everybody's support so anyway it's good luck with your project and thanks a lot for watching

Please explain how to plant bare root strawberry plants

we're going to demonstrate how easy it is to plant two bare-root strawberries once your shipment arrives go ahead and take them out soak them in a container of water for approximately 15 minutes after they're finished soaking we recommend trimming off the bottom quarter of the root system this helps them to establish the plan faster once it's in your soil you want to lay out your soil marking your holes approximately 12 to 18 inches apart and then when you're putting the plant in you'll just want to keep the crown of the plant level with the top of the soil just go ahead and spread the soil back around it pack it in a little bit to help the plant stay upright and you're going to find this is so easy to do the grandkids or even want to help you out then after they're planted in the ground for about a month this is what they're going to look like right here and then this what they look like about three months enjoy your strawberry plants you

Please explain how to do a slip knot 123... ( for micro braids)

okay so I'm going to show you how you can do a slip nap first you want to take a small portion of here very small just like that and the way I do it I do like this take my two fingers in between go over pass it through and go up like that and just secure it even more I'm going to take this small piece of here split it or divide it into two and just make a knot and a second knot and that's how you do a slipknot okay so let's do a second one remember hold this portion up here hold the braid take a small portion just like this then you want to go around these two fingers like that and pass it up just like that and to secure you want to make a split you want to divide it like that make a knot and a second one and that's how you do a slipknot

Please explain how to clean and sanitize your keg before kegging your homebrew

hi yes sir yes guys we are in my bathroom now I am cleaning today cakes okay tanks now I've done a video years ago where I used to there's the cake you see the big bad boy I need a video years ago in here where I used to do my bottles in the bathroom cleaning them I don't do that anymore people get all sketched out because of the tub and you know it's filling up the tub with water and sanitizer clean the [ __ ] out of the damn things it was sanitized like a mother but then they'd rather have you cleaned in your laundry Basin itself more you know dirty clothes wash that's [ __ ] but in it so I don't do in the bath of anyone although it's a fine place to do their own problems long sanitized kegs are a different story dang cakes this bad boy won't fit my sink you need a great big washtub which I think I'm looking at turning a room into a great big home brewing facility which is pretty cool and then I'm gonna have a couple basins in it the whole deal set me back with rickenrock okay so cleaning your cakes I'm going to take some beers today this video you're not going to see that you've tuned in to the other ones I'm just cleaning the cakes very important like anything else you got a sanitized [ __ ] and anything to do with your home brewski so what do you do first of all you take your big back cake you dump it all the old beer looms in there I just dumped the remnants of a stout they made the other one was the lager and the other one was an IPA so I got three on the go I'm just gonna talk you through this because it's very hard for me to hold the camera and you know pop up with the water in it and [ __ ] so you want it dump it in I then put her under the big tap full or full of water I put the lid back on the old cake ski there's the lid container a little tricky if you've never done one before this is the old Pepsi kegs slider in like that not good I'm handy but I need that damn handy put the cover on that thing with some water and shake it up get all the debris out of it then what you do guys is you take yourself again the good old handy-dandy non scent Hansel put her in there put the lid back on put some water in there shake her up and and what I'll do is I'll take my little brush key little brush key into homebrew store you get at amazon.com whatever I scrub the [ __ ] out of it Mexico shipping down there and make sure you get all the loose debris over there because you don't want those floaties sitting around your beer I didn't dump the cake down the old drain I then fill er up with water again not all the way but you know put some water in there put the cover back on Swisher up real good like and then dump batter then I get the old star sound stars and kills everything so you don't like my bathroom too damn bad this crap killed everything so I put the star Sanon put some water and cover on shaker all up dump her out and then depending if I'm going to store them or not sometimes I'll even leave the star sand in there filled out and then store the cake star same in it why not or you could just dump it out and then seal the cake and you'll be good to go if you do that I'm in either way cuz I'm pretty you know when it comes to the sanitizing you guys like my shower and all that cool back of my video yeah not gonna shower for you simply relax and then what I would do would be to again before I group some beer with them but actually I'm going to sorry the free cakes and very many cakes um today I'm gonna do a forest carbonation as well as prime the other one with sugar so two different ways but you have to tune into a different video to hear all about how that works but then before I kick any beer I would definitely sanitize again so that's what I got guys I'm not gonna walk you through it that's it okay if you're not used to Kagan you can get the old these are the old ones that you'll pop and so Duran if this one's an old Pepsi when you can get the coke one most of your homebrew stores have them you get them online I've seen one hand a lot of stuff too I brew 24 liters in a batch America you guys brewing 819 he's holding 19 that's cool me with 24 I also get the bottle some so that's that's cool as well Kings are also cool because I do like the bottom like they'll take a bottle bigger in there as well kegs are cool though because you could also get a growler if you want to take your beer somewhere and fill up the growler from the cake once it's fully carbonated and you can take a pair with you too so that's cool to it that's what I got for you guys anyone who doesn't know me I'm big robbed from meek beer easy.com I typically am not hanging in my shower so chill over the first video that you've seen make beer easy calm head over there you can get all my updates you can get all my I give it some recipes tips I'm giving away right now a free boot camp beer making boot camp you can sign up for that then subscribe to my channel give me a like if you liked it give me a comment even if you didn't like it let me know you're out there and checking this [ __ ] out and yeah just say hey guess always cool to hear from other : Brewers that's what I got dogs I'm out of here time to clean some pigs in me shower later guys forgot one thing I'm cleaning your cake I did forget I just forget to do the video you gotta take these little contraptions off here these little bad boys okay the end me out the little one is the in co2 in take it out and the out it has a great big long thing under it you get it they get it and clean and sanitize it okay now I know let me see some of the wrench what is this this is 11 16 I think yeah the eleventh 16th take today perfectly you don't strip the matter name like that it's basically on there like that they just screw on you can see screw on take them off give them a cleaning I don't spend a lot of time I mean I guess this thing's full of sanitizer someone I tip it up and down you know squish it all around they're getting sanitized too but you should do that as well take a little cloth rub under them you know sometimes I find that they build up some gunk and stuff that's it guys yeah I saw Mike closing the last last before the commercial break that is so I head on over that make beer easy.com sign up for mathletes comment like

Please explain how to keep your natural hair and scalp healthy

hello again welcome to in the kitchen with Levesque we have got the beautiful model nella my new muse and I think one of the biggest questions ever is that when people will think that you are waves or you add extensions in general the leaves they tend to think you just forget about your hair underneath everything and just leave it be not it's not true no the thing is you have to take care of your hair yeah but okay I don't really take care of my hair as a shoe I just like okay I'm moisturize I put some oil sometimes yeah I just most of the time I just like blow dry or no yeah I don't know it's bad but the thing is actually every time you wear a wig or extension in my case I'm just gonna keep it two weeks because most of my clients are interested in that once every month or every couple of weeks you're going to have to give your hair a hot oil treatment that means you're gonna mix your favorite oils together you're going to dump in a moisture right moisture your hair with some water and then you're gonna put the products on it that is the only time I would recommend blow drying your hair just to get the heat to open up the follicles of your hair okay so you can the wear weight and look absolutely fabulous whenever you want to but you have to take care of your afro because you you know you can't just hide it under there I think that's the most important thing I want to get out to you guys now and don't forget about your hair okay in this video today I'm going to show you how to do a hot oil treatment we're gonna use Nullah as the base because it's a lot easier for me to do it on somebody else than to do it on myself and show it on camera because I live alone so I don't have a camera mine i feature everything myself but Nana's wearing one of my fabulous ways that I've made this is a verging Peruvian hair 26 inches 24 inches 22 inches and 20 inches with a matching closure now it's very very full it's very thick it's very gorgeous but yes and I was over hair it's equally gorgeous if not even more vortex 7s unit today so we're going to take a moment and she's gonna take off her wig and she's gonna come back and we're gonna show you her natural hair okay we're back and this is what was hiding underneath the unit now our units supposed to be used as a protective styling not not a highly style because it's just not good we have like this Mane under there that needs to be taken care of these show some TLC what we're gonna do is we're gonna divide up the hair in four pieces now if you're gonna detangle your hair we recommend you use a tangle tweezer simply because it doesn't hurt it doesn't rip out your hair and is very good to use on afro hair as well or baby hair young people's hair it's okay you can get these act another would you say you can buy it you can get anywhere I think of them as your name hmm later and check out kicks as well I'm excited yeah yeah yeah they sometimes have this this so there you go what we're going to do is we're going to separate my hair using our house no combs or anything and divide it into four sections so that we can actually access the hair there you go divide it into four we've got two pieces here and then we're going to go in and divide those two into another two I hope I'm not how to you know nothing there you go so we're gonna divide that into two as well and then we're gonna keep it up here this time yes do you know what I'm doing from her angry right about now I'm something really like MMB so just make sure it's separated into four and because that's what you will be working with later so what I'm going to do now is I'm going to show you how I what I mix and how I mix it and then we're going to come back to how they put it in the Hat all right so what you're gonna need for this is a little bowl to mix all of your oil then the oils I'll be mixing today is argan oil the organic argan oil I'm going to use the golden fork over oil I'm going to be using the virgin or coconut oil right here I'll be using the share button I'll be using castor oil and I'll be using a little bit of avocado oil just a tiny bit of that now these are the favorite ones that I like to mix because it's so thick and it gives you your hair exactly what it needs now how I measure it is I use a spoon so I was showing you exactly how much of everything I put in well the first thing I use is the sheer butter I will take a spoonful of sheer butter because it's quite thick so utiful spoon of that let me just do that I will take more of the coconut oil just simply because it gets really oily and it goes well on the scout and being used I would put one full tablespoon of castor oil notice how thick it is pour it in make sure you close it and put it back in its place yes I will also put the argan oil now I'll use more of this because it's quite healthy for the hair so I'll put two tablespoons of the Argent world in the mixture one tablespoon of the jojoba oil and with the avocado oil I don't actually measure it I just go by ear play by ear so I just pour a tiny bit here and here's what what she looks like now this makes sure I'm going to heat up and once this all melted we're gonna flip that on now this hair when you heat up the oil you get a mixture that is full liquid so when you have the bottle filled with water and conditioner you're going to moisturize the hair taking each section and just make sure it's saturated so as she holds up I'm gonna take a tablespoon and pop it into the hair as like this then I'm going to massage it in whilst putting in even one don't forget the roots don't forget the edges old neglect please to massage the scalp with the hair as well just go in and just be gently massage your scalp now we're back I've got the hair dryer I like to use that over the hair just do lucky in the heat not too much just a tiny bit and then if you have a shower cap you can pop that over your head if you don't have a shower cap you know what you can do you can pop over to 7-eleven go get yourself a bag girl and then walk it over your hair like that I like the color so the colors are sweet and then you're gonna tie it at the back and tuck it in knit things up and then you can you grab a African hair light or a heavy do running whatever you have a horn and you're going to wrap it around your head like this done this is just an extra method of keeping locking in the heat onto your hair and letting those oils soak in like I said if it's a Friday night and you're not going out do this treatment and sleep with it on because overnight the longer you have it in your hand the better it just means that your hair gets that extra time to lock in the moisture all right Wow we'll be right back okay so the hair has now being rinsed out we've Co watched it we haven't used any shampoo we've only used conditioner so I can assure you no shampoos were harmed in the making of this video look at the natural coils of the hair right here look I'm working with the castor oil on the edges and the back of the hair so do is now I'm going to go in with the coconut oil into the scalp of the hair