Datasets:

ramixpe

/

sp_dataset_llama

like 0

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: CPAK-3-LANE_5_LOW_TX_POWER_WARNING ### Response: (Severity: 3), (Category: PLATFORM), (Description: Environmental monitoring has detected a CPAK Tx power less than or equal to the low Tx power warning threshold. The CPAK is the pluggable optics on the line cards. The Tx power threshold values are read from the CPAK.), (Recommended Action: Verify that the device is properly inserted. Replace the CPAK with a working one (if any) to isolate bad optics. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands 'show tech-support ethernet interface location <loc>', 'show hw-module fpd location all' and 'admin show inventory'.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_10_0 ### Response: (Severity: 1), (Category: FABRIC), (Description: SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_10 interrupt on FIA), (Recommended Action: Wait a few minutes. If it doesn't recover, please reload the board using command 'reload location <>'. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: MKA-3-TX_INSTALL_FAILURE ### Response: (Severity: 3), (Category: L2), (Description: TxSA/TxSC programming has failed. As recovery, session would be bought down on this interface, followed by session bringup. Traffic hit expected.), (Recommended Action: contact cisco-support by sharing the tech-support macsec.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: INSTHELPER-6-ISSU_GO_ACTIVE ### Response: (Severity: 6), (Category: INSTALL), (Description: During ISSU operation node received node role change notification .Node will change to active.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: How can you monitor EEM reliability metrics in Cisco IOS XR? ### Response: EEM reliability metrics in Cisco IOS XR can be monitored using the 'show event manager metric' command. This command displays information about the EEM system, including policy execution counts, success rates, and failure reasons.

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: HA_WD-6-MEMORY_RECOVERY_KILL_NON_PROCESSMGR ### Response: (Severity: 6), (Category: HA), (Description: The process with the indicated name and pid has been killed in an attempt to recover system memory. Since this process is not managed by processmgr, it may not be restarted. The process can be manually restarted if desired, but may continue to consume large amounts of memory.), (Recommended Action: The system is critically short of memory. Automatic recovery will attempt to stabilize the system, but there is either a memory leak or a misconfiguration. Both require operator intervention.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: OPTICS-3-BAD_FPGA_IMAGE ### Response: (Severity: 3), (Category: L2), (Description: The indicated FPGA image in SPI flash does not appear to have a valid meta-data. This means that a previous FPD upgrade operation did not finish the programming operation of the image.), (Recommended Action: Run again the 'upgrade hw-module location <loc> fpd <fpd_name>' command to re-program the image.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: FEA_DLL-3-TCAM_ERR ### Response: (Severity: 3), (Category: PKT_INFRA), (Description: Feature EA DLL encountered error in completing TCAM operation. This can lead to mismatch between hardware and software configuration.), (Recommended Action: The most common cause of this error is that there no more free TCAM entries available for ACL. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: MRIB-3-NSFSTATE ### Response: (Severity: 3), (Category: ROUTING), (Description: An internal error occurred when MRIB attempted to transition to/from Non-stop Forwarding mode.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: CE_TFTP-3-ERR ### Response: (Severity: 3), (Category: IP), (Description: The CE-TFTP server process exitted due to some reason.), (Recommended Action: The system will try again. No action is required.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: QSFP_PLUS-3-LANE_0_HIGH_TEMP_WARNING ### Response: (Severity: 3), (Category: PLATFORM), (Description: Environmental monitoring has detected a QSFP+ laser temperature greater than or equal to the high temperature warning threshold. The QSFP+ is the pluggable optics on the line cards. The temperature threshold values are read from the QSFP+.), (Recommended Action: Verify that the device is properly inserted, the fan is operational and empty slots have filler cards installed. Check the 'show environment temperatures'. If the system temperature is normal then replace the optics with working one (if any). If the system temperature is not normal, verify the fan speed and make sure installation is compliance with 'Cisco ASR 9000 Series Aggregation Service Router Hardware Installation Guide'. Check specifically the 'Chassis Air Flow Guidelines' and 'Rack-Mounting and Air Flow clearance guidelines'. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands 'show tech-support ethernet interface location <loc>', 'show hw-module fpd location all', 'admin show inventory', 'show environment temperatures' and 'admin show environment fans'.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: CHKPT_PROXY-7-PUTENV ### Response: (Severity: 7), (Category: HA), (Description: The proxy process uses putenv() to communicate with the checkpoint library. A call to putenv() failed with the specified error.), (Recommended Action: No action is required.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: What is a composite bootable file in IOS XR? ### Response: A composite bootable file (e.g., comp-hfr-mini.vm-3.6.0) is a single file that contains all the packages needed to boot a router and provide full routing functionality. It includes the base OS, routing protocols, forwarding, and management packages. Composite bootable files simplify the process of installing and booting IOS XR.

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: MPLS_LCAC-7-ERR_INTERNAL ### Response: (Severity: 7), (Category: ROUTING), (Description: An internal system error occured.), (Recommended Action: Copy the message exactly as it appears and report it to your technical service representative.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: CFP-3-LANE_2_HIGH_TEMP_WARNING ### Response: (Severity: 3), (Category: PLATFORM), (Description: Environmental monitoring has detected a CFP laser temperature greater than or equal to the high temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.), (Recommended Action: Verify that the device is properly inserted, the fan is operational and empty slots have filler cards installed. Check the 'show environment temperatures'. If the system temperature is normal then replace the optics with working one (if any). If the system temperature is not normal, verify the fan speed and make sure installation is compliance with 'Cisco ASR 9000 Series Aggregation Service Router Hardware Installation Guide'. Check specifically the 'Chassis Air Flow Guidelines' and 'Rack-Mounting and Air Flow clearance guidelines'. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands 'show tech-support ethernet interface location <loc>', 'show hw-module fpd location all', 'admin show inventory', 'show environment temperatures' and 'admin show environment fans'.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: ISIS-4-DUPLICATE_MT_CAPABILITY ### Response: (Severity: 4), (Category: ROUTING), (Description: The specified LSP contains multiple items advertising the same MT capability. This is an indication that the router which owns the LSP has generated its LSP incorrectly. If the MT capability items contain conflicting overload state then the message indicates this and IOS-XR determines that the router which issued the LSP is overloaded. If the MT capability items contain conflicting attached state then the message indicates this and IOS-XR determines that the router which issued the LSP is not attached.), (Recommended Action: Identify the source of the offending packet and correct it.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: LDP-5-NBR_CHANGE ### Response: (Severity: 5), (Category: ROUTING), (Description: A LDP neighbor has changed state (up/down). If neighbor has gone down, then a reason for session going down is also displayed. This message appears only if the <Bold>mpls ldp log neighbor<NoBold> command is configured.), (Recommended Action: No action is required.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: MPLS_VPN_MIB-3-ERR_TRACE_INIT ### Response: (Severity: 3), (Category: OS), (Description: mpls vpn mib could not initialize the tracing module), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: SHELFMGRV2-3-FORCED_POWEROFF_FAILED ### Response: (Severity: 3), (Category: PLATFORM), (Description: Multiple attempts to force the powering off of the node have failed. No further attempts will be made, all boot request sent from this affected node will not be processed.), (Recommended Action: Some hardware issue on the card might be preventing a successful power off opeartion by the system. Please contact Cisco TAC with information about this error message for support.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: FLOWTRAP-4-BAD_ACTOR_MAC_DETECTED ### Response: (Severity: 4), (Category: OS), (Description: The punt flow trap sampler detected an excessive flow from a source MAC address. This could result in a denial of service to other interfaces. All traffic from this source MAC address will be dropped for a specified time period.), (Recommended Action: No action necessary. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. *RECUR*)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: TACACSD-3-PARAMETER ### Response: (Severity: 3), (Category: SECURITY), (Description: An invalid argument was passed to either the tacacsd or one of its funtions.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: RIP_POLICY-3-ORA_RUN ### Response: (Severity: 3), (Category: ROUTING), (Description: Internal error in the routing policy library.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: PCIMGR-7-DEBUG_INFO ### Response: None

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: PLX_FPD-3-UPGRADE_MD5SUM_ERROR ### Response: (Severity: 3), (Category: DRIVER), (Description: PLX FPD EEPROM is corrupted or due to I2C issues, incorrect values are being read leading to mismatch in md5sum between the EEPROM and the stored md5sum. The output of 'show hw-module fpd' will show the affected FPD.), (Recommended Action: Try another FPD upgrade operation.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: INFRA_MSG-5-RUN_LOGIN ### Response: (Severity: 5), (Category: INFRA), (Description: User logged into shell by executing run command), (Recommended Action: This is informational that user accessed the linux shell of the router.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: LPTS_PREIFIB-4-EVM_TM_LEAF_NEW ### Response: (Severity: 4), (Category: OS), (Description: An internal error was detected when trying to create a managed timer tree leaf for the event manager.), (Recommended Action: Restarting the process may fix the issue.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: PMIPV6-3-OUT_OF_MEMORY ### Response: (Severity: 3), (Category: IP), (Description: pmipv6d process is running out of memory. This could be due to a memory leak. It is also possible that the process has not entirely run out of memory, but there is no single block of memory of requested size available.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log. Issue the <CmdBold>show processes pmipv6d detail<noCmdBold> command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the <CmdBold>show processes pmipv6d detail<noCmdBold> output, call your Cisco technical support representative and provide the representative with the gathered information. Using the Job ID from the above command, run the following command: Copy the error message exactly as it appears on the console or in the system log. Issue the <CmdBold>show processes memory <Job ID><noCmdBold> command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the <CmdBold>show processes memory <Job ID><noCmdBold> output, call your Cisco technical support representative and provide the representative with the gathered information. Copy the error message exactly as it appears on the console or in the system log. Issue the <CmdBold>show memory summary<noCmdBold> command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the <CmdBold>show memory summary<noCmdBold> output, call your Cisco technical support representative and provide the representative with the gathered information. Copy the error message exactly as it appears on the console or in the system log. Issue the <CmdBold>show ipv6 mobile pmipv6 trace<noCmdBold> command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the <CmdBold>show ipv6 mobile pmipv6 trace<noCmdBold> output, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: T1E1-4-WARNING ### Response: (Severity: 4), (Category: L2), (Description: A warning is generated while executing the function in question. The message contains info about the location and cause of the failure and possibly anticipated actions/effects.), (Recommended Action: Verify continued correct operation of T1E1.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: CTRLIO-3-WAIT_EOD_FAIL ### Response: (Severity: 3), (Category: PKT_INFRA), (Description: 'while waiting for EOD signal API failed.' 'process will exit with failure.'), (Recommended Action: 'Retry the issu operation.If error persists.' 'contact tac with 'show tech-support issu'.')

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: IOFPGA-3-MAIN_THREAD_BLOCKED ### Response: (Severity: 3), (Category: DRIVER), (Description: When IOFPGA driver main thread is blocked for more than the indicated time, key functionality of the driver will be affected. To allow the driver to recover from this condition, it will restart itself as part of error handling operation.), (Recommended Action: Collect the iofpga_driver core file generated because of this restart and report the problem to Cisco TAC for support.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: FGID_SVR-3-UNHANDLED_FGID_DNLD ### Response: (Severity: 3), (Category: FABRIC), (Description: --), (Recommended Action: No action is required.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: DUMPER-4-SYSDB_SET_FAIL ### Response: (Severity: 4), (Category: OS), (Description: Dumper stored various config related data in sysdb and it failed to get sysdb item. This might impact the dumper.), (Recommended Action: Please contact support with the following data. 1. show exception 2. admin show exception trace dumper severity info 3. admin show exception trace dumper-config severity info 4. show logging 5. show-tech sysdb)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: FPD_BURNER-3-NO_MEM ### Response: (Severity: 3), (Category: PLATFORM), (Description: No enough memory.), (Recommended Action: No action is required..)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: ASR9K_LICENSE-2-ENFORCE_OOC ### Response: (Severity: 2), (Category: LICENSE), (Description: The licensed feature is enabled without appropriate licenses.), (Recommended Action: The customer should either purchase more licenses or disable the feature.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: ISSU_INFRA-3-STATE_LIB_ERROR ### Response: (Severity: 3), (Category: INSTALL), (Description: An unexpected failure occurred attempting to read or update key ISSU state.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: CBC-3-SLOT_ID_CHANGE ### Response: (Severity: 3), (Category: PLATFORM), (Description: CBC detected unexpected slot id change. The system can no longer manage/monitor the card's environment conditions. Normally this means some HW issue on slot id pins, there are 6 pins per board to indicate a valid slot, if any of the pin has noise which get changed during card operation, we will see this alert), (Recommended Action: Reboot the LC. If the problem persists Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: d1qnetio-3-SUBBLOCK_REG_FAILED ### Response: (Severity: 3), (Category: L2), (Description: The software forwarding support for IEEE802.1Q VLANs was unable to initialise on the specified node. Software forwarding VLAN functionality on the affected is likely not to work.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: RIB-3-ECMP_ERR_ADD ### Response: (Severity: 3), (Category: ROUTING), (Description: Protocol has registered for no ecmp support but is adding more than one path for a route.), (Recommended Action: *SUPPORT*)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: I2C-3-BP_EN_ERROR ### Response: (Severity: 3), (Category: PLATFORM), (Description: Error while trying to grab or release the lock.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: XLNC-6-INSTALL_OBTAIN_VERSION_FAIL ### Response: (Severity: 6), (Category: INFRA), (Description: XLNC has tried to read the loaded kernel version and the on-disk kernel version and has been unable to obtain this information. XLNC will not restart as part of an initial resync.), (Recommended Action: Please check the kernel module is loaded and that exi_driver.ko is on the disk.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: TTY-6-SYSDB_INTERN ### Response: (Severity: 6), (Category: MGBL), (Description: TTY Server is trying to access Sysdb-mc and an error [no members in group] is returned from Sysdb-mc to all the Clients. This is a generic issue with all the admin band processes which comes up earlier than sysdb svrs will have to attempt the reconnect to sysdb with ECM retry.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: What is the purpose of the ignore-lsp-errors command in IS-IS? ### Response: The ignore-lsp-errors command allows a router to ignore LSP packets with checksum errors rather than purging them. This can be useful in networks with faulty implementations that may generate LSPs with checksum errors. However, it is generally not recommended as it can lead to routing inconsistencies.

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: CFP-2-LANE_7_HIGH_BIAS_ALARM ### Response: (Severity: 2), (Category: PLATFORM), (Description: Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias threshold values are read from the CFP.), (Recommended Action: Verify that the device is properly inserted. Check installation is compliance with 'Cisco ASR 9000 Series Aggregation Service Router Hardware Installation Guide'. Check all the FPDs are upto date using 'show hw-module fpd location all'. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands 'show tech-support ethernet interface location <loc>', 'show hw-module fpd location all' and 'admin show inventory'.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: PSU-3-INVALID_DATA_IN_IDPROM ### Response: (Severity: 3), (Category: LIBRARY), (Description: The power module IDRPOM is not properly programmed.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: FSDB_AGG-1-FABRIC_MODE_CHANGE ### Response: (Severity: 1), (Category: FABRIC), (Description: User has configured a fabric mode change. This configuration does not take effect without router reload. If standby RP present, wait for standby to be Opertional (check by 'show platform')), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: SIM_INFRA-6-INSTALL_ROLE ### Response: (Severity: 6), (Category: PLATFORM), (Description: Role installation completed.), (Recommended Action: Reload the module using 'hw-module location <ISM> reload')

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: FIA-1-SKT_SP0_INTR_SLICE6_WORD_OUTSYNC_0 ### Response: (Severity: 1), (Category: FABRIC), (Description: SKT_SP0_INTR_SLICE6_WORD_OUTSYNC interrupt on FIA), (Recommended Action: Wait a few minutes. If it doesn't recover, please reload the board using command 'reload location <>'. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: LDP-3-RX_BAD_PREFIX_LEN ### Response: (Severity: 3), (Category: ROUTING), (Description: An LDP message containing a destination IP Prefix with a bad prefix length has been received from a peer.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: FSYNC-6-SSM_EPRTC ### Response: (Severity: 6), (Category: L2), (Description: The quality level of the source has been changed to or from ePRTC.), (Recommended Action: None, this is an informational condition that does not require troubleshooting.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: ISIS-3-EVENT_CONN_CREATE_FAIL ### Response: (Severity: 3), (Category: ROUTING), (Description: IS-IS failed to create a connection to an essential service during initialization. This is an internal software error. It requires a restart of the isis process for recovery.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: BRIDGE-1-XAUI_1_CHAR_ALIGN_0 ### Response: (Severity: 1), (Category: PLATFORM), (Description: XAUI to NPU-1 char alignment error on bridge instance-0.), (Recommended Action: If the error persists, please reload the board using the command 'reload location <>'. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: CMPP-4-ERR_EVM_CREATE ### Response: (Severity: 4), (Category: INFRA), (Description: CMPP failed to create its Event Manager which is a critical resource for the operation of the process. This error may be caused by low memory resources. The process will abort and be restarted in an attempt to recover.), (Recommended Action: Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. *SUPPORT*)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: FABRIC_DRVR-1-ERR_HW_INIT ### Response: (Severity: 1), (Category: FABRIC), (Description: The board initialization failed the specified operation while configuring the device. The driver will exit and attempt to come up again. On multiple such failures, the board will be shutdown permanently by the shelf manager.), (Recommended Action: Collect console logs. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: XTC-5-SR_POLICY_CANDIDATE_PATH_CHANGE ### Response: (Severity: 5), (Category: OS), (Description: An SR policy changed to use a new candidate path preference. This message appears only if the <Bold>segment-routing logging policy status<NoBold> command is configured.), (Recommended Action: If changing from a higher to lower preference, Use the reason under the inactive candidate path to determine reason for path invalidation as a hint to triage it further.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: ENVMON-2-SAT_FAN_AF_MISMATCH ### Response: (Severity: 2), (Category: PLATFORM), (Description: This alarm is generated when fantrays's in the satellite are of opposite air flow type to each other. Satellite chassis shutsdown after two minutes from the time alarm is raised.), (Recommended Action: Please use fan trays of same air flow type.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: SCONBKUP-7-RELOAD_REPLY_ERR ### Response: (Severity: 7), (Category: MGBL), (Description: Error encountered while replying message during ASCII System Configuration.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: SYSDB-4-ENCODER_ERR ### Response: (Severity: 4), (Category: SYSDB), (Description: Error starting bag encoder.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: FIA-1-SKT_SP1_INTR_SLICE_ERR_2_0 ### Response: (Severity: 1), (Category: FABRIC), (Description: SKT_SP1_INTR_SLICE_ERR_2 interrupt on FIA), (Recommended Action: Wait a few minutes. If it doesn't recover, please reload the board using command 'reload location <>'. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: INVMGR-3-FAILURE ### Response: (Severity: 3), (Category: PLATFORM), (Description: an external API has failed in Inventory Manager. The details are supplied with the msg.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: XTC-5-PCE_PEER_STATE_CHANGE ### Response: (Severity: 5), (Category: OS), (Description: An PCE peer has changed state. This message appears only if the <Bold>segment-routing logging pce peer-status <NoBold> command is configured for the XTC.), (Recommended Action: No action is required.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: LIBIPPIMDLL-3-ENS_NRS_FAIL ### Response: (Severity: 3), (Category: IP), (Description: An error occurred during ENS or NRS communication between the PIM and BGP processes. This can occur when the pim bgp producer or the pim mdt safi consumer - -fails to register/unregister with the ENS -fails to create NRS class), (Recommended Action: This indicates a problem with ENS or NRS. Do the following action to check for errors. Copy the error message exactly as it appears on the console or in the system log. Issue the <CmdBold>show pim trace bgp error<noCmdBold> command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the <CmdBold>show pim trace bgp error<noCmdBold> output, call your Cisco technical support representative and provide the representative with the gathered information. Copy the error message exactly as it appears on the console or in the system log. Issue the <CmdBold>show mlib trace error<noCmdBold> command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the <CmdBold>show mlib trace error<noCmdBold> output, call your Cisco technical support representative and provide the representative with the gathered information. Copy the error message exactly as it appears on the console or in the system log. Issue the <CmdBold>show pim bgp-safi<noCmdBold> command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the <CmdBold>show pim bgp-safi<noCmdBold> output, call your Cisco technical support representative and provide the representative with the gathered information. Copy the error message exactly as it appears on the console or in the system log. Issue the <CmdBold>show pim trace mdt bgp<noCmdBold> command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the <CmdBold>show pim trace mdt bgp<noCmdBold> output, call your Cisco technical support representative and provide the representative with the gathered information. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: FABRICQ_MGR-4-ERR_IMDR_NOTIFY ### Response: (Severity: 4), (Category: FABRIC), (Description: The Fabricq Mgr received an event from the iMDR Mgr that it did not register for.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: LC_CPIDB-2-OPEN ### Response: (Severity: 2), (Category: PLATFORM), (Description: A run time error occurred while initializing the lc idb on the linecard. The reason for the error is dispalyed. Please call Cisco Support with the error information), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: FPD-6-INFO ### Response: (Severity: 6), (Category: PLATFORM), (Description: This is a info message from FPD operation.), (Recommended Action: *NONE*)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: What is the purpose of the MPLS TE auto-bandwidth underflow feature? ### Response: The MPLS TE auto-bandwidth underflow feature allows auto-bandwidth to react more quickly to drops in traffic flow by triggering an immediate bandwidth adjustment when the measured rate drops below a configured underflow threshold. It aims to free up bandwidth on the tunnel path more promptly when traffic decreases significantly.

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: IGMP_MTRACE-3-MSG_ERROR ### Response: (Severity: 3), (Category: ROUTING), (Description: Messaging error), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information as given in the required info.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: GDOI-4-SVC_WARNING ### Response: (Severity: 4), (Category: OS), (Description: A service API warning is displayed.), (Recommended Action: *SUPPORT*)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: FAB_SVR_TOPAZ-7-ERR_INIT ### Response: (Severity: 7), (Category: FABRIC), (Description: Fabric server encountered the specified error during the initialization sequence. This facility is deemed crucial and hence the process is automatically restarted on this failure. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: spp-6-SPAN_FILE_WRITE_SUCCESSFUL ### Response: (Severity: 6), (Category: PKT_INFRA), (Description: SPAN write to file was successful.), (Recommended Action: No action is required.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: RADIUSD-3-RIB_LOCAL_ADDRESS_ERR ### Response: (Severity: 3), (Category: SECURITY), (Description: An internal software error has occurred.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: CROSSBAR-1-SERDES_ERROR_LNK4 ### Response: (Severity: 1), (Category: PLATFORM), (Description: Crossbar driver detected a serdes error on link 4.), (Recommended Action: If this alarm persists for a period of 60 seconds after all the cards are in IOS-XR RUN state, then please reload the card using command: 'hw-module loc <> reload'. Please make sure all the cards in the chassis are properly seated and their ejector handle screws completely tightened. Also, check for any damage to the card and its backplane connectors. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: XBAR-7-ERR_LWM_EVENT_BLOCK ### Response: (Severity: 7), (Category: PLATFORM), (Description: Crossbar driver Event Manager event block error), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: PBR-3-EA_INIT ### Response: (Severity: 3), (Category: FORWARDING), (Description: This message indicates that an error has occurred during the 'pbr_ea' process initialization and it may prevent PBR from functioning. Particular reason is included in the message), (Recommended Action: Allow the 'pbr_ea' process to restart with the command <CmdBold>process restart pbr_ea location <node id><NoCmdBold>. If the problem persists, contact Cisco TAC.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: TACACSD-3-ERR_CONFIG_SERVER ### Response: (Severity: 3), (Category: SECURITY), (Description: A configuration error has occured.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: CFP-3-LANE_0_LOW_TEMP_WARNING ### Response: (Severity: 3), (Category: PLATFORM), (Description: Environmental monitoring has detected a CFP laser temperature less than or equal to the low temperature warning threshold. The CFP is the pluggable optics on the line cards. The temperature threshold values are read from the CFP.), (Recommended Action: The system detected a low temperature threshold crossing which normally won't affect any service. Monitor the system to see if the condition clears. Generally no action needs to be taken for this condition and is more informational. If any service is affected, check the device is properly inserted. Replace the CFP with working one (if any). Check all the FPDs are upto date using 'show hw-module fpd location all'. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands 'show tech-support ethernet interface location <loc>', 'show hw-module fpd location all', 'admin show inventory', 'show environment temperatures' and 'admin show environment fans'.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: PLIM-4-XFP_HOTSWAP ### Response: (Severity: 4), (Category: L2), (Description: The inserted XFP failed to power on correctly during initialization.), (Recommended Action: None. Software corrected the issue by power cycling the XFP.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: STATSD-3-SHMEM_CORRUPTED ### Response: (Severity: 3), (Category: MGBL), (Description: In certain unlikely scenarios it is possible that during a process restart the shared memory region used by the stats infrastructure can become corrupted. In most cases this will automatically be recovered from, however there is a possibility that the system will not be able to recover from this - The specific instance of the message will indicate which of these cases has arisen. If the system is unable to restart all necessary processes then multiple process crashes/blockages may be observed. In either case, reported statistics may be reset or inaccurate.), (Recommended Action: In the recovery case, processes should restart automatically and the system should recover so no user intervention should be required. If we are unable to automatically recover, then either the node should be reloaded, or support contacted.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: DAD-3-SETUP ### Response: (Severity: 3), (Category: ROUTING), (Description: There was something illegal about the setup operations that where performed. This should be a straight coding error that will fail everytime and should be cleaned up before releasing the code.), (Recommended Action: Copy the message exactly as it appears and report it to your technical service representative.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: PPP_MA-4-ERR_BACKEND ### Response: (Severity: 4), (Category: L2), (Description: PPP MA encountered an error using the Backend service related to use of either SysDB or SubDB. The error message describes what operation has failed and why it failed. The most likely reason for this is low memory resources or a programming error.), (Recommended Action: Consider restarting the PPP MA process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: INSTMGR-3-XR_ISO_MISSING_IN_INPUT ### Response: (Severity: 3), (Category: INFRA), (Description: XR iso should be provided in the input while carving new SDR. Invalid input.), (Recommended Action: Provide XR ISO in the input image list and try carving SDR again.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: BRIDGE-1-XAUI_1_TX_FIFO_OFLOW_1 ### Response: (Severity: 1), (Category: PLATFORM), (Description: XAUI interface to NPU-1 reported tx fifo overflow on bridge instance - 1.), (Recommended Action: If the error persists, please reload the board using the command 'reload location <>'. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: L2VPN-6-MAC_LIMIT_PW_SET ### Response: (Severity: 6), (Category: L2), (Description: Number of MAC addresses in the pseudowire has reached the configured maximum. If MAC limit action to disable MAC learning and unicast flooding has been configured on the port, then that particular action might have been taken automatically.), (Recommended Action: No particular action is required.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: RDM_LIB-6-RWLOCK_TIMEOUT ### Response: (Severity: 6), (Category: PLATFORM), (Description: The RDM server timed-out waiting to acquire a write lock on the global (context) read-write lock. This could happen if the client was holding the lock for too long or has exited. The RDM server will continue to operate.), (Recommended Action: The RDM server will continue to operate despite of this condition. Check if any of the rdm client processes are exit or crashed.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: VS_CLIENT-3-CACHE_LOOKUP ### Response: (Severity: 3), (Category: INSTALL), (Description: Test code only - will never be seen by customers.), (Recommended Action: --)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: NPU_DRVR-3-SLICE_FAILURE ### Response: (Severity: 3), (Category: FABRIC), (Description: 1. Slice failure: Slice failure affecting all slices and no slice is powered UP.), (Recommended Action: System is not usuable. Power failure happened during system boot. Need to reload the board for recovery. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: DUMPER-7-SYSDB_ITEM_TYPE_BAD ### Response: (Severity: 7), (Category: OS), (Description: Dumper keeps various config related data in sysdb. Unexpected item type under config for dumper. This might impact the funcitoning of the dumper.), (Recommended Action: Restart dumper config and see if the issue is resolved. If not please contact support with the following data. 1. show exception 2. admin show exception trace dumper severity info 3. admin show exception trace dumper-config severity info 4. show logging 5. follow process <dumper pid> 6. show-tech sysdb 7.If possible please collect debug messages of dumper.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: FSDB_AGG-3-PM_INIT_FAILURE ### Response: (Severity: 3), (Category: FABRIC), (Description: FSDB server failed PM initialization with above reson.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: NPU_DRVR-3-HW_MODULE_PROFILE_TTL_CHASSIS_CFG_CHANGED ### Response: (Severity: 3), (Category: FABRIC), (Description: 1. If the hw-module command is used to configure the user defined configs, there will be inconsistency between the user config and the hardware. Since the driver in LC has already started the asic initalization process before this config is received. Needs attention with reloading the chassis.), (Recommended Action: N/A If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: NPUXBAR_BRIDGE-2-PCIE_TXIF_FIFO_SBE ### Response: (Severity: 2), (Category: PLATFORM), (Description: CIB PCIe Tx interface FIFO single bit error.), (Recommended Action: None.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: LIBNOTIFY-7-MEMORY ### Response: (Severity: 7), (Category: INSTALL), (Description: The system is running out of memory and was not able to allocate sufficient memory to carry out the requested operation), (Recommended Action: Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: EDRM_SERVER-3-PROCESS_INIT ### Response: (Severity: 3), (Category: L2), (Description: The initialization of the EDRM server process failed due to the indicated reason.), (Recommended Action: None. The process initialization will be retried automatically.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: FGID_AGG-3-ERR_INTERNAL_SW ### Response: (Severity: 3), (Category: FABRIC), (Description: The FGID Aggregator encountered the annunciated SW error. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to recover. If the problem continues, sysmgr will trigger node reload. After a certain number of node reloads, the shelf manager will permanently shutdown the node.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: CPAK-3-LANE_5_HIGH_TEMP_WARNING ### Response: (Severity: 3), (Category: PLATFORM), (Description: Environmental monitoring has detected a CPAK laser temperature greater than or equal to the high temperature warning threshold. The CPAK is the pluggable optics on the line cards. The temperature threshold values are read from the CPAK.), (Recommended Action: Verify that the device is properly inserted, the fan is operational and empty slots have filler cards installed. Check the 'show environment temperatures'. If the system temperature is normal then replace the optics with working one (if any). If the system temperature is not normal, verify the fan speed and make sure installation is compliance with 'Cisco ASR 9000 Series Aggregation Service Router Hardware Installation Guide'. Check specifically the 'Chassis Air Flow Guidelines' and 'Rack-Mounting and Air Flow clearance guidelines'. If the issue persists then copy the error message exactly as it appears, and report it to your technical support representative. If possible, also provide the output of the commands 'show tech-support ethernet interface location <loc>', 'show hw-module fpd location all', 'admin show inventory', 'show environment temperatures' and 'admin show environment fans'.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: CONFIGEDM-3-FAILEDREGCOMP ### Response: (Severity: 3), (Category: MGBL), (Description: 'Compiling a regular expression failed with the reason mentioned in the message. This may lead to wrong 'show config failed' listing.'), (Recommended Action: Please contact TAC with the output of the following commands: - console logs - show version - show process nvgen_server - show nvgen trace ascii-backup reverse - show configuration history If the error recurs frequently, it may be possible to rectify it by restarting 'nvgen_server' process. But please collect the logs mentioned above, before restarting the process.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: IMFPGA-3-IDT_RECOV_CLK_ERR ### Response: (Severity: 3), (Category: PLATFORM), (Description: IDT Recovery clock I2C Failure/Success while accessing device), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: CIH-1-ASIC_ERROR_PERSIST_THRESHOLD ### Response: (Severity: 1), (Category: PLATFORM), (Description: An ASIC error threshold was crossed.), (Recommended Action: *None*)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: PRP_UPGRADE-3-SPAWN_RM ### Response: (Severity: 3), (Category: MGBL), (Description: Failed to spawn the 'rm' process. Unable to remove existing configuration from PRP.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_11_0 ### Response: (Severity: 1), (Category: FABRIC), (Description: SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_11 interrupt on FIA), (Recommended Action: Wait a few minutes. If it doesn't recover, please reload the board using command 'reload location <>'. Make sure board is seated properly. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: TUNNEL_GRE_EA-3-UPDATE_ERR ### Response: (Severity: 3), (Category: PLATFORM), (Description: This is an error message in the platform specific code software to indicate anomolies while initializing GRE Feature. This error is most likely caused by a temporary situation within the feature code. %s - indicates the reason for the failure.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.)

Below is an instruction that describes a task, paired with an input that provides further context. Write a response that appropriately completes the request. ### Instruction: You are expert in Cisco Service provider technology, and Cisco IOS XR issues ang syslog ### Input: MXPDRVR-6-NCS1K_PORT_RESET_SUCCESS ### Response: None