input
stringclasses 1
value | instruction
stringlengths 223
3.4k
| output
stringlengths 206
380
| category
stringclasses 1
value | index
stringclasses 1
value | fileName
null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "各NPθ動力線接続",
"WorkItems": [
"★1. 各NP θ動力線を接続"
],
"WorkPoints": [
"CN21 = CN21K301 (NP1 θ動力線)",
"CN23 = CN23K301 (NP2 θ動力線)",
"CN25 = CN25K301 (NP3 θ動力線)"
],
"Tolks": [],
"InspectionNo": "GWETP-F013-002",
"InspectionItems": [
"検査表①:ﾒｲﾝ基板接続確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"CN21K301",
"CN25K301",
"CN23K301",
"GWETP-F013-002"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに接続出来ている事",
"Method": "目視",
"RecordMethod": "GWETP-F013-002",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "各NPZ動力線接続",
"WorkItems": [
"2. ﾌﾞﾗｹｯﾄに結束する",
"★1. 各NPZﾓｰﾀｰ電源ｺﾈｸﾀｰを接続"
],
"WorkPoints": [
"CN22 = CN22K301 NP1 Z動力線",
"CN24 = CN24K301 NP2 Z動力線",
"CN26 = CN26K301 NP3 Z動力線"
],
"Tolks": [],
"InspectionNo": "GWETP-F013-002",
"InspectionItems": [
"検査表①:ﾒｲﾝ基板接続確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"CN22K301",
"CN26K301",
"CN24K301",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"GWETP-F013-002"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに接続出来ている事",
"Method": "目視",
"RecordMethod": "GWETP-F013-002",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "50cN･m",
"WorkName": "補強2取付",
"WorkItems": [
"1. ①に②をBOLT WASHER にて取付"
],
"WorkPoints": [
"電空ﾚｷﾞｭﾚｰﾀのｴｱﾁｭｰﾌﾞをくぐる様に②を取付",
"②のｲﾝｼｭﾛｯｸは省いて描いています"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "Z軸ﾓｰﾀｰ配線ﾏｰｷﾝｸﾞ",
"WorkItems": [
"1. ①のZ軸ﾓｰﾀｰ配線にﾏｰｷﾝｸﾞ実施"
],
"WorkPoints": [
"一部を除いて描いています",
"【注意】 配線は引っ張り過ぎ無い事",
"NP1=ﾓｰﾀｰﾎﾞﾃﾞｨより50mm",
"NP2=ﾓｰﾀｰﾎﾞﾃﾞｨより45mm",
"NP3=ﾓｰﾀｰﾎﾞﾃﾞｨより45mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"NP1",
"NP2",
"NP3",
"45mm",
"50mm",
"CN4K302",
"CN6K302",
"CN2K302"
]
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "NP1信号線/ﾗﾌ原点ｾﾝｻｰ接続・結束",
"WorkItems": [
"4. 配線3本を結束",
"★1. CN2を接続",
"★2. CN11を接続",
"★3. CN1を接続"
],
"WorkPoints": [
"CN2K302 ※NP1 Z信号線",
"CN11K302を接続 ※NP1 ﾗﾌ原点ｾﾝｻｰ",
"CN1K302を接続 ※NP1 θ信号線",
"【注意】 ｲﾝｼｭﾛｯｸ頭は低く設置する",
"配線ﾏｰｷﾝｸﾞと結束ﾎﾟｲﾝﾄを合わす"
],
"Tolks": [],
"InspectionNo": "GWETP-F013-002",
"InspectionItems": [
"検査表①:I/O基板接続確認",
"検査表①:I/O基板接続確認",
"検査表①:I/O基板接続確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"CN1K302",
"CN2K302",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"CN11K302",
"3本を結束",
"ﾏｰｷﾝｸﾞと結束ﾎﾟｲﾝﾄを合わす",
"CN2K302とCN11K302のﾏｰｷﾝｸﾞと結束ﾎﾟｲﾝﾄを合わす",
"ﾏｰｷﾝｸﾞと結束ﾎﾟｲﾝﾄを合わす",
"GWETP-F013-002"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに接続出来ている事",
"Method": "目視",
"RecordMethod": "GWETP-F013-002",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "NP2信号線/ﾗﾌ原点ｾﾝｻｰ接続・結束",
"WorkItems": [
"4. 配線3本を結束",
"5. 空中配線5本を結束",
"★1. CN4を接続",
"★2. CN10を接続",
"★3. CN3を接続"
],
"WorkPoints": [
"CN4K302 ※NP2 Z信号線",
"【注意】 ｲﾝｼｭﾛｯｸ頭は低く設置する",
"CN3K302を接続 ※NP2 θ信号線",
"CN10K302を接続 ※NP2 ﾗﾌ原点ｾﾝｻｰ",
"配線ﾏｰｷﾝｸﾞと結束ﾎﾟｲﾝﾄを合わす"
],
"Tolks": [],
"InspectionNo": "GWETP-F013-002",
"InspectionItems": [
"検査表①:I/O基板接続確認",
"検査表①:I/O基板接続確認",
"検査表①:I/O基板接続確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"空中線5本を結束",
"CN3K302",
"CN4K302",
"CN10K302",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"3本を結束",
"ﾏｰｷﾝｸﾞと結束ﾎﾟｲﾝﾄを合わす",
"CN4K302とCN10K302のﾏｰｷﾝｸﾞと結束ﾎﾟｲﾝﾄを合わす",
"ﾏｰｷﾝｸﾞと結束ﾎﾟｲﾝﾄを合わす",
"GWETP-F013-002"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに接続出来ている事",
"Method": "目視",
"RecordMethod": "GWETP-F013-002",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "NP3信号線/ﾗﾌ原点ｾﾝｻｰ接続・結束",
"WorkItems": [
"4. 配線3本を結束",
"5. 空中配線4本を結束",
"★1. CN6を接続",
"★2. CN5を接続",
"★3. CN7を接続"
],
"WorkPoints": [
"CN5K302を接続 ※NP3 θ信号線",
"CN6K302 ※NP3 Z信号線",
"CN7K302を接続 ※NP3 ﾗﾌ原点ｾﾝｻｰ",
"【注意】 ｲﾝｼｭﾛｯｸ頭は低く設置する",
"【注意】 配線を送り過ぎ無い事",
"配線ﾏｰｷﾝｸﾞと結束ﾎﾟｲﾝﾄを合わす"
],
"Tolks": [],
"InspectionNo": "GWETP-F013-002",
"InspectionItems": [
"検査表①:I/O基板接続確認",
"検査表①:I/O基板接続確認",
"検査表①:I/O基板接続確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"CN5K302",
"CN7K302",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"3本を結束",
"空中線4本を結束",
"CN6K302",
"CN6K302とCN7K302のﾏｰｷﾝｸﾞと結束ﾎﾟｲﾝﾄを合わす",
"ﾏｰｷﾝｸﾞと結束ﾎﾟｲﾝﾄを合わす",
"GWETP-F013-002"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに接続出来ている事",
"Method": "目視",
"RecordMethod": "GWETP-F013-002",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "60cN･m",
"WorkName": "FAN取付",
"WorkItems": [
"1. ①に②をSCREW にて取付"
],
"WorkPoints": [
"【注意】 FAN配線とﾌﾞﾗｹｯﾄ抜き穴周辺の干渉"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"【干渉確認】 FAN配線とﾌﾞﾗｹｯﾄ抜き穴周辺の干渉がないか",
"【干渉確認】 FANのﾎﾞﾙﾄと配線の干渉がないか確認",
"引き回やすいように､ｺﾈｸﾀｰの位置を確認してから設置する"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN接続",
"WorkItems": [
"★1. CN27を接続"
],
"WorkPoints": [
"CN27 = FAN配線",
"FAN配線はｲﾝｼｭﾛｯｸの外側を通す"
],
"Tolks": [],
"InspectionNo": "GWETP-F013-002",
"InspectionItems": [
"検査表①:I/O基板接続確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"CN27",
"ｲﾝｼｭﾛｯｸとﾌﾞﾗｹｯﾄの間を通す",
"GWETP-F013-002"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに接続出来ている事",
"Method": "目視",
"RecordMethod": "GWETP-F013-002",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾞﾙﾌﾞ1側及び電空線接続",
"WorkItems": [
"2. 配線を結束",
"★1. CN33を接続",
"★3. CN12を接続"
],
"WorkPoints": [
"CN33 = CN33K301(ﾊﾞﾙﾌﾞ1側)",
"【注意】 ｲﾝｼｭﾛｯｸ頭は低く設置する",
"CN12 = CN12(電空線)"
],
"Tolks": [],
"InspectionNo": "GWETP-F013-002",
"InspectionItems": [
"検査表①:I/O基板接続確認",
"検査表①:I/O基板接続確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"CN33K301",
"継手に結束",
"CN12",
"2本を結束",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"GWETP-F013-002"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに接続出来ている事",
"Method": "目視",
"RecordMethod": "GWETP-F013-002",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾞﾙﾌﾞ3側接続",
"WorkItems": [
"★1. CN30を接続"
],
"WorkPoints": [
"CN30 = CN30K301(ﾊﾞﾙﾌﾞ3側)"
],
"Tolks": [],
"InspectionNo": "GWETP-F013-002",
"InspectionItems": [
"検査表①:I/O基板接続確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"CN30K301",
"GWETP-F013-002"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに接続出来ている事",
"Method": "目視",
"RecordMethod": "GWETP-F013-002",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ接続1",
"WorkItems": [
"1. ﾄﾞﾛｱｺﾈｸﾀｰ配線は下図の状態で使用する",
"★2. CN32を接続",
"★3. CN31を接続"
],
"WorkPoints": [
"CN31 = CN31(ﾄﾞﾛｱｺﾈｸﾀｰ)",
"配線をﾈｼﾞってｸｾを付ける",
"CN32 = CN32(ﾄﾞﾛｱｺﾈｸﾀｰ)"
],
"Tolks": [],
"InspectionNo": "GWETP-F013-002",
"InspectionItems": [
"検査表①:ﾒｲﾝ基板接続確認",
"検査表①:ﾒｲﾝ基板接続確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"図の様な状態で使用する",
"心線の向きを把握して",
"CN31",
"CN32",
"ねじる",
"GWETP-F013-002"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに接続出来ている事",
"Method": "目視",
"RecordMethod": "GWETP-F013-002",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "80cN･m",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ接続2",
"WorkItems": [
"■1. FG線を固定"
],
"WorkPoints": [
"一部を除いて描いています"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "GWETP-F013-002",
"InspectionItems": [
"検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"FG線",
"FG線",
"■安全作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "50cN･m",
"WorkName": "補強3取付",
"WorkItems": [
"1. ①に②をBOLT にて取付"
],
"WorkPoints": [
"赤丸部分のﾈｼﾞ穴がｾﾝﾀｰになる様にBOLT で取付【作業目安】 ①の歪は修正しながら取付ける",
"一部を省いて描いています"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "補強3結束1",
"WorkItems": [
"1. ﾄﾞﾛｱｺﾈｸﾀｰ配線を結束",
"2. 配線の干渉確認"
],
"WorkPoints": [
"一部を省いて描いています",
"手順1 黒ｺﾈｸﾀｰ線とFG線を結束",
"手順2 黄色矢印方向に配線を引き､配線と板金ｴｯｼﾞ部分に余裕をつくる ※緑線部分が板金ｴｯｼﾞ",
"手順3 手順2の状態で結束",
"板金ｴｯｼﾞ部分と配線の干渉を確認",
"【重要】 結束はﾄﾞﾛｱｺﾈｸﾀｰ線が上側､FG線が下側になること ※略図参照(板金ｴｯｼﾞから遠ざける為)",
"基板ｴｯｼﾞ部分と配線の干渉を確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"手順3手順2の状態で結束",
"手順2黄色矢印の方向に配線を引く配線と板金ｴｯｼﾞ部分に余裕をつくる為 ※緑線部分",
"手順1上:ﾄﾞﾛｱｺﾈｸﾀｰ線下:FG線",
"ここの曲げは､下向きに折ってｸｾをつける",
"【注意】心線がｽﾍﾟｰｻｰに干渉しないこと"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "補強3結束2",
"WorkItems": [
"2. 結束",
"★1. ①にCABLE 中継線を接続"
],
"WorkPoints": [
"CN29K301 = CN9K302",
"ﾄﾞﾛｱｺﾈｸﾀｰ配線､ﾊﾞﾙﾌﾞ3側線､中継線を結束"
],
"Tolks": [],
"InspectionNo": "GWETP-F013-002",
"InspectionItems": [
"検査表①:I/O基板接続確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"CN9K302",
"CN29K301",
"ﾄﾞﾛｱｺﾈｸﾀｰ配線",
"ﾊﾞﾙﾌﾞ3側線",
"中継配線",
"GWETP-F013-002"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに接続出来ている事",
"Method": "目視",
"RecordMethod": "GWETP-F013-002",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ配線結束1",
"WorkItems": [
"1. 配線を結束"
],
"WorkPoints": [
"ﾄﾞﾛｱｺﾈｸﾀｰ配とﾊﾞﾙﾌﾞ3側線を同時結束",
"【注意】 FAN線はここでは結束しない",
"【注意】 ｲﾝｼｭﾛｯｸ頭は低く設置する",
"一部を除いて描いています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"手順1 黄色矢印方向にﾊﾞﾙﾌﾞ線を送って結束2本を結束･ﾄﾞﾛｱｺﾈｸﾀｰ線･ﾊﾞﾙﾌﾞ3側線",
"ﾊﾞﾙﾌﾞ3側線は矢印方向に送ってから結束",
"手順2 黄色矢印方向にﾄﾞﾛｱｺﾈｸﾀｰ線を送ってから結束2本を結束･ﾄﾞﾛｱｺﾈｸﾀｰ線･ﾊﾞﾙﾌﾞ3側線※2本のみ(FAN線は結束しない)"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN配線結束",
"WorkItems": [
"1. FAN線を結束"
],
"WorkPoints": [
"一部を除いて描いています",
"【注意】 ｲﾝｼｭﾛｯｸ頭は低く設置する",
"【注意】 板金ｴｯｼﾞ部分との干渉が無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"【注意】FAN線が板金ｴｯｼﾞ部分との干渉が無い事"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ配線結束2",
"WorkItems": [
"1. ﾄﾞﾛｱｺﾈｸﾀｰ配線とﾊﾞﾙﾌﾞ3側線を結束"
],
"WorkPoints": [
"手順1 ﾄﾞﾛｱｺﾈｸﾀｰ配線を黄色線方向に送り､緑線部分で余らせる",
"手順2 結束する",
"一部を除いて描いています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"結束",
"結束"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "電空ﾚｷﾞｭﾚｰﾀ配線結束",
"WorkItems": [
"1. 電空ﾚｷﾞｭﾚｰﾀ配線を結束",
"2. 配線とｴｱﾁｭｰﾌﾞを結束"
],
"WorkPoints": [
"一部を除いて描いています",
"一部を除いて描いています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ﾀｲﾏｳﾝﾄに結束",
"結束",
"結束"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ｸﾘｱﾗﾝｽ確認",
"WorkItems": [
"1. ｸﾘｱﾗﾝｽ確認"
],
"WorkPoints": [
"制御ﾌﾞﾗｹｯﾄ上面にｽｹｰﾙを設置して､配線上面とのｸﾘｱﾗﾝｽが1mm以上ある事を確認する"
],
"Tolks": [],
"InspectionNo": "GWETP-F013-001",
"InspectionItems": [
"検査表①:配線､ｲﾝｼｭﾛｯｸ飛び出し無し確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｽｹｰﾙ"
]
}
|
{
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｸﾘｱﾗﾝｽ1㎜以上",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け",
"WorkItems": [
"1. COVER の貼付け面を清掃する",
"■2. 略図寸法にLABEL LABEL LABEL を貼付け"
],
"WorkPoints": [
"【注意】 貼付けるCOVER の向きを確認すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"■安全作業"
]
}
|
{
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "60cN･m",
"WorkName": "ｶﾊﾞｰ取付",
"WorkItems": [
"■1. ①に②をSCREW にて取付",
"2. ｶﾊﾞｰとの干渉確認"
],
"WorkPoints": [
"【完成ﾍｯﾄﾞ保管時の注意】下略図の向きで保管の際は､部品吸着用ﾁｭｰﾌﾞの破損を避ける為ﾍｯﾄﾞ下側に十分な大きさの養生材等を実施する事",
"ｶﾊﾞｰ取付後､ｶﾊﾞｰと配線の干渉が無いか確認"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "GWETP-F013-002",
"InspectionItems": [
"検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認"
],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"部品吸着用ﾁｭｰﾌﾞ",
"養生材",
"■安全作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "付属品ﾊﾟｯｷﾝｸﾞ",
"WorkItems": [
"1. SPRING FILTER TUBE (130MM CUT) CLAMP をﾊﾟｯｷﾝｸﾞして､付属品とする"
],
"WorkPoints": [
"【完成ﾍｯﾄﾞ保管時の注意】下略図の向きで保管の際は､部品吸着用ﾁｭｰﾌﾞの破損を避ける為ﾍｯﾄﾞ下側に十分な大きさの養生材等を実施する事",
"付属品はﾊﾟｯｷﾝｸﾞして､ﾍｯﾄﾞ完成品と合わせて払い出す"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"部品吸着用ﾁｭｰﾌﾞ",
"養生材",
"付属品",
"合わせて払い出す",
"130mm"
]
}
|
{
"QualityItem": "付属品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "ｽｰﾊﾟｰｼｬｲﾅ",
"WorkName": "ﾍﾞｰｽ組立①",
"WorkItems": [
"1. BASE に油砥石をかける"
],
"WorkPoints": [
"表裏､指示箇所に砥石をかけ､ﾊﾞﾘ･ｶｴﾘ等を取除く"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"表面",
"裏面"
]
}
|
{
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ・ｶｴﾘ等が無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "認識穴黒色化対策",
"WorkItems": [
"1. ①に②③を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"拡大"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立②",
"WorkItems": [
"▲1. ②に①を接着剤で取付ける"
],
"WorkPoints": [
"ｱﾙｺｰﾙで清掃後､②の取付穴にｽｰﾊﾟｰXを塗布し､①を取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"接着剤塗布 ｺﾞﾏ粒:2"
]
}
|
{
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "接着剤ｽｰﾊﾟｰX",
"ProcessNames": [
"特殊工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立③",
"WorkItems": [
"◆1. ②にPIN を取付ける"
],
"WorkPoints": [
"PIN PIN外周にｸﾞﾘｰｽを塗布し､治具で圧入する",
"ﾋﾟﾝ出代2㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2"
]
}
|
{
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立③",
"WorkItems": [
"◆1. ②にPIN を取付ける"
],
"WorkPoints": [
"PIN PIN外周にｸﾞﾘｰｽを塗布し､治具で圧入する",
"ﾋﾟﾝ出代2㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2",
"◆作業者安全作業"
]
}
|
{
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "Dﾋﾟﾝ圧入治具(表側)",
"Size": "",
"ToolOther": "FM-3031",
"WorkName": "ﾍﾞｰｽ組立④",
"WorkItems": [
"1. ②にPIN を圧入する"
],
"WorkPoints": [
"②の裏面にPIN を4個､圧入する",
"ﾋﾟﾝ出代 :3mm",
"FM-3031の上にのせてﾋﾟﾝを圧入する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
}
|
{
"QualityItem": "出代確認",
"ToolManageNo": "FM-3031",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "Dﾋﾟﾝ圧入治具",
"Size": "",
"ToolOther": "FM-2072",
"WorkName": "ﾍﾞｰｽ組立④",
"WorkItems": [
"1. ②にPIN を圧入する"
],
"WorkPoints": [
"②の裏面にPIN を4個､圧入する",
"ﾋﾟﾝ出代 :3mm",
"FM-3031の上にのせてﾋﾟﾝを圧入する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
}
|
{
"QualityItem": "出代確認",
"ToolManageNo": "FM-2072",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立④",
"WorkItems": [
"1. ②にPIN を圧入する"
],
"WorkPoints": [
"②の裏面にPIN を4個､圧入する",
"ﾋﾟﾝ出代 :3mm",
"FM-3031の上にのせてﾋﾟﾝを圧入する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
}
|
{
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "Dﾋﾟﾝ圧入治具(表側)",
"Size": "",
"ToolOther": "FM-3031",
"WorkName": "ﾍﾞｰｽ組立⑤",
"WorkItems": [
"1. ②にPIN を圧入する"
],
"WorkPoints": [
"FM-3031の上にのせてﾋﾟﾝを圧入する",
"圧入時はFM-3202を使用",
"出代はすべて2㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
}
|
{
"QualityItem": "出代確認",
"ToolManageNo": "FM-3031",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "PIN圧入治具",
"Size": "",
"ToolOther": "FM-3202",
"WorkName": "ﾍﾞｰｽ組立⑤",
"WorkItems": [
"1. ②にPIN を圧入する"
],
"WorkPoints": [
"FM-3031の上にのせてﾋﾟﾝを圧入する",
"圧入時はFM-3202を使用",
"出代はすべて2㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
}
|
{
"QualityItem": "出代確認",
"ToolManageNo": "FM-3202",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立⑤",
"WorkItems": [
"1. ②にPIN を圧入する"
],
"WorkPoints": [
"FM-3031の上にのせてﾋﾟﾝを圧入する",
"圧入時はFM-3202を使用",
"出代はすべて2㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
}
|
{
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立⑥",
"WorkItems": [
"1. SHEET を指定の寸法にｶｯﾄする",
"2. ②に1でｶｯﾄしたｼｰﾄを貼付ける",
"1. SHEET を指定の寸法にｶｯﾄする",
"2. ②に1でｶｯﾄしたｼｰﾄを貼付ける"
],
"WorkPoints": [
"黄色丸:長さ16㎜×16枚",
"貼付面の清掃､脱脂を行う",
"貼付寸法無きところは壁面当て､端面合わせで貼付け",
"黄色丸:長さ16㎜×16枚",
"貼付面の清掃､脱脂を行う",
"貼付寸法無きところは壁面当て､端面合わせで貼付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"4㎜",
"2㎜",
"4㎜",
"2㎜"
]
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾍﾞｱﾘﾝｸﾞDﾋﾟﾝ圧入治具",
"Size": "",
"ToolOther": "FM-2250",
"WorkName": "ﾍﾞｰｽ組立⑦",
"WorkItems": [
"1. 治具(FM-2250)にBEARING を挿入し 上治具をｾｯﾄする",
"2. 1.上治具の穴に､PIN を挿入･圧入する",
"3. 2.の上治具を外し､ SPACER を挿入する"
],
"WorkPoints": [
"治具･下側の列にﾍﾞｱﾘﾝｸﾞを4個挿入する",
"PIN ﾋﾟﾝの取付方向に注意の事",
"･治具にBEARING を挿入",
"ﾃｰﾊﾟ",
"※ ﾋﾟﾝ方向 ﾃｰﾊﾟが上側",
"･ﾊﾝﾄﾞﾌﾟﾚｽで圧入する (ﾋﾟﾝ浮きが無い事)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"※D-pin(2ヶ所)と穴(2ヶ所)を はめ込む(赤矢印参照)"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-2250",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ組立⑧",
"WorkItems": [
"1. ①に②を圧入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. ③にBLOCK BLOCK をBOLT で取付ける"
],
"WorkPoints": [
"ﾏｰｷﾝｸﾞはﾎﾞﾙﾄ頭のみにする事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾍﾞｱﾘﾝｸﾞN003取付",
"WorkItems": [
"1. ③にBEARING SPACER をBOLT で取付ける",
"◆2. 1.完成品のﾍﾞｱﾘﾝｸﾞ部にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"ﾏｰｷﾝｸﾞはﾎﾞﾙﾄ頭のみにする事",
"ﾍﾞｱﾘﾝｸﾞ(大･小 各4個)外周にｸﾞﾘｰｽを塗布する"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各1",
"◆作業者安全作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｱﾘﾝｸﾞN003取付",
"WorkItems": [
"1. ③にBEARING SPACER をBOLT で取付ける",
"◆2. 1.完成品のﾍﾞｱﾘﾝｸﾞ部にｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"ﾏｰｷﾝｸﾞはﾎﾞﾙﾄ頭のみにする事",
"ﾍﾞｱﾘﾝｸﾞ(大･小 各4個)外周にｸﾞﾘｰｽを塗布する"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各1"
]
}
|
{
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "",
"WorkName": "周辺部品面処理",
"WorkItems": [
"1. GUIDE BLOCK BLOCK COLLAR に砥石を掛ける"
],
"WorkPoints": [
"全体に油砥石を掛け､ﾊﾞﾘ等の無き事の確認を行う",
"油砥石は表面処理がはげない程度に掛ける事",
"GUIDE は全面に油砥石をかける",
"BLOCK BLOCK COLLAR は上下面に油砥石をかける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
}
|
{
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ等無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ面処理",
"WorkItems": [
"1. SHUTTER に砥石を掛ける"
],
"WorkPoints": [
"表裏面のｴｯｼﾞ部分､穴加工部に油砥石を軽く掛け､ﾊﾞﾘ等の無き事の確認を行う表面に傷が入らない用に注意",
"表面:刻印有り穴加工部付近に砥石を掛ける",
"裏面:刻印無し全体的に軽く砥石を掛ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
}
|
{
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ等無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｼｬｯﾀｰ組立",
"WorkItems": [
"1. ①に②をBOLT で取付ける"
],
"WorkPoints": [
"②を①ｼｬｯﾀｰに平行に取付",
"上面 刻印番号有り",
"青線部 ｼｬｯﾀｰとの隙間無い事",
"黄色面 定盤上でｶﾞｲﾄﾞをｼｬｯﾀｰに平行取付"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ組立",
"WorkItems": [
"1. ①に②をBOLT で取付ける",
"◆2. 1.完成品にWASHER を貼付ける"
],
"WorkPoints": [
"②を①ｼｬｯﾀｰに平行に取付",
"上面 刻印番号有り",
"青線部 ｼｬｯﾀｰとの隙間無い事",
"黄色面 定盤上でｶﾞｲﾄﾞをｼｬｯﾀｰに平行取付",
"WASHER ﾜｯｼｬｰ表裏にｸﾞﾘｰｽを塗布し貼付",
"片側にM4小径を貼付"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1"
]
}
|
{
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ取付①",
"WorkItems": [
"◆1. SPRING にｸﾞﾘｰｽを塗布する",
"2. ①の上に②をおく",
"3. 2.完成品にSPRING を挿入 ､③④をBOLT BOLT で仮取付け"
],
"WorkPoints": [
"表面全体にｸﾞﾘｰｽを塗布",
"①ｶﾞｲﾄﾞを押えた状態で ③･④を取付 (ｽﾌﾟﾘﾝｸﾞ飛出しの為)",
"②にｸﾞﾘｰｽ塗布したSPRING を挿入",
"①ｶﾞｲﾄﾞ穴にﾋﾟﾝを挿入",
"③をBOLT で仮取付け",
"④をBOLT で仮取付け",
"本締め: SD-0147931-016",
"* 1.完成品のﾋﾟﾝ部にｽﾌﾟﾘﾝｸﾞを挿入し､①のｶﾞｲﾄﾞ部に挿入 ③をBOLT BOLT で仮固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2"
]
}
|
{
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ取付②",
"WorkItems": [
"1. ①に②をBOLT ･③BOLT で仮取付",
"2. 1.完成品に③をBOLT で仮取付"
],
"WorkPoints": [
"本締め: SD-0147931-016",
"本締め: SD-0147931-016"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｼｬｯﾀｰ取付③",
"WorkItems": [
"2. 仮締めﾎﾞﾙﾄを締結する(緑丸6ヵ所)"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"裏面",
"表面"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ装着確認治具",
"Size": "",
"ToolOther": "FM-2902",
"WorkName": "ｼｬｯﾀｰ動作確認",
"WorkItems": [
"1. ①ｼｬｯﾀｰの動作確認を行う"
],
"WorkPoints": [
"①を㉖冶具(FM-2902)にｾｯﾄする",
"ｼｬｯﾀｰをﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞで押して､開く時のｽﾄﾛｰｸ全域での最大荷重を測定する※この確認はあくまでの最終検査前の事前確認です",
"目安値: 4.2N 以下",
"最終検査はSD-A0147931-022にて実施"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"FM-2902"
]
}
|
{
"QualityItem": "動作確認",
"ToolManageNo": "FM-2902",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "目安値4.2N以下",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ動作確認",
"WorkItems": [
"1. ①ｼｬｯﾀｰの動作確認を行う"
],
"WorkPoints": [
"①を㉖冶具(FM-2902)にｾｯﾄする",
"ｼｬｯﾀｰをﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞで押して､開く時のｽﾄﾛｰｸ全域での最大荷重を測定する※この確認はあくまでの最終検査前の事前確認です",
"目安値: 4.2N 以下",
"最終検査はSD-A0147931-022にて実施"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"FM-2902"
]
}
|
{
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "1回/1年",
"ToolRecord": "校正成績書",
"StdVal": "目安値4.2N以下",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "周辺部品取付",
"WorkItems": [
"◆1. ①にGUIDE をSPACER BOLT で取付ける"
],
"WorkPoints": [
"GUIDE の内側にｸﾞﾘｰｽを塗布後､取付",
"GUIDE は右側に当付けて取付"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:3"
]
}
|
{
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:3",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "周辺部品取付",
"WorkItems": [
"◆1. ①にGUIDE をSPACER BOLT で取付ける"
],
"WorkPoints": [
"GUIDE の内側にｸﾞﾘｰｽを塗布後､取付",
"GUIDE は右側に当付けて取付"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:3",
"◆作業者安全作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｽﾍﾟｰｻｰ取付・動作確認",
"WorkItems": [
"3. COLLAR をBOLT で取付ける",
"2. WASHER をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:各1",
"◆作業者安全作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾍﾟｰｻｰ取付・動作確認",
"WorkItems": [
"◆1. ①WASHER にｸﾞﾘｰｽを塗布する",
"2. WASHER をBOLT WASHER で取付ける",
"3. COLLAR をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"◆作業者安全作業"
],
"Words": [
"･内面(側面)に ｸﾞﾘｰｽを塗布する",
"ｸﾞﾘｰｽ塗布 米粒:各1",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:各1"
]
}
|
{
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:各1ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾎﾟｽﾄ取付",
"WorkItems": [
"1. ①にSPACER をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付",
"WorkItems": [
"1. ①にLABEL LABEL ④を貼付ける"
],
"WorkPoints": [
"指示箇所にﾗﾍﾞﾙを貼付け､剥がれ無い事を確認する"
],
"Tolks": [],
"InspectionNo": "WDQB-F013-020",
"InspectionItems": [
"検査表①:.ﾗﾍﾞﾙ貼付確認"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1㎜",
"30㎜",
"32㎜",
"26㎜",
"2㎜",
"0.5㎜",
"5㎜"
]
}
|
{
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ装着確認治具",
"Size": "",
"ToolOther": "FM-2902",
"WorkName": "機能検査",
"WorkItems": [
"1. ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ着脱確認",
"3. ﾁｪﾝｼﾞｬｰの自重落下確認",
"2. ｼｬｯﾀｰの動作確認",
"4. ﾉｽﾞﾙ挿抜確認"
],
"WorkPoints": [
"･着脱の際､引っかかりが無い事",
"･ｽﾄﾛｰｸﾞ全域で最大荷重を測定する (4.2N 以下)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ着脱確認",
"検査表①:ｼｬｯﾀｰ動作確認",
"検査表①:ﾉｽﾞﾙ挿抜確認",
"WDQB-F013-020"
]
}
|
{
"QualityItem": "脱着確認",
"ToolManageNo": "FM-2902",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "引っ掛かりが無い事",
"Method": "目視",
"RecordMethod": "WDQB-F013-020",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "機能検査",
"WorkItems": [
"2. ｼｬｯﾀｰの動作確認",
"4. ﾉｽﾞﾙ挿抜確認"
],
"WorkPoints": [
"･ｽﾄﾛｰｸﾞ全域で最大荷重を測定する (4.2N 以下)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:ｼｬｯﾀｰ動作確認",
"検査表①:ﾉｽﾞﾙ挿抜確認",
"WDQB-F013-020"
]
}
|
{
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "1回/1年",
"ToolRecord": "校正成績書",
"StdVal": "4.2N以下",
"Method": "目視",
"RecordMethod": "WDQB-F013-020",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "HANDY-CHECKER",
"Size": "",
"ToolOther": "OMRONE39-VA",
"WorkName": "機能検査",
"WorkItems": [
"1. ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ着脱確認",
"3. ﾁｪﾝｼﾞｬｰの自重落下確認"
],
"WorkPoints": [
"･着脱の際､引っかかりが無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ着脱確認"
]
}
|
{
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに点灯する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"Size": "",
"ToolOther": "FM-2169",
"WorkName": "機能検査",
"WorkItems": [
"1. ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ着脱確認",
"3. ﾁｪﾝｼﾞｬｰの自重落下確認",
"2. ｼｬｯﾀｰの動作確認",
"4. ﾉｽﾞﾙ挿抜確認"
],
"WorkPoints": [
"･着脱の際､引っかかりが無い事",
"･ｽﾄﾛｰｸﾞ全域で最大荷重を測定する (4.2N 以下)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ着脱確認",
"検査表①:ｼｬｯﾀｰ動作確認",
"検査表①:ﾉｽﾞﾙ挿抜確認",
"WDQB-F013-020"
]
}
|
{
"QualityItem": "挿抜確認",
"ToolManageNo": "FM-2169",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｽﾑｰｽﾞである事",
"Method": "手感",
"RecordMethod": "WDQB-F013-020",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "3ﾉｽﾞﾙ治具",
"Size": "",
"ToolOther": "",
"WorkName": "機能検査",
"WorkItems": [
"1. ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ着脱確認",
"2. ｼｬｯﾀｰの動作確認",
"4. ﾉｽﾞﾙ挿抜確認",
"3. ﾁｪﾝｼﾞｬｰの自重落下確認"
],
"WorkPoints": [
"･着脱の際､引っかかりが無い事",
"･ｽﾄﾛｰｸﾞ全域で最大荷重を測定する (4.2N 以下)",
"･引っかかりが無くｽﾑｰｽﾞな事･ﾉｽﾞﾙに遊びがある事･ｼｬｯﾀｰが閉じた状態でﾉｽﾞﾙが 抜け無い事",
"･ｽｲｯﾁ開側(上)で開ﾗﾝﾌﾟ (点灯)する事･ｽｲｯﾁ閉側(下)で閉ﾗﾝﾌﾟ (点灯)する事",
"※9ｽﾃｰｼｮﾝにﾉｽﾞﾙ冶具をｾｯﾄして確認する事",
"･隙間無い事",
"･ﾁｪｯｶｰが点灯 する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"･自重落下する事",
"･ﾚﾊﾞｰを押す",
"･ｼｬｯﾀｰ｢開｣でﾉｽﾞﾙｾｯﾄ",
"･ｼｬｯﾀｰ｢閉｣",
"･ｼｬｯﾀｰ｢開閉｣ｽｲｯﾁ",
"FM-2169",
"FM-2902",
"検査表①:ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ着脱確認",
"検査表①:ｼｬｯﾀｰ動作確認",
"検査表①:ﾉｽﾞﾙ挿抜確認",
"WDQB-F013-020"
]
}
|
{
"QualityItem": "挿抜確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "引っ掛かりが無い事",
"Method": "手感",
"RecordMethod": "WDQB-F013-020",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｰﾄ確認",
"WorkItems": [
"1. ｼｰﾄ(傷防止)が剥がれてい無い事を確認する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｼｰﾄ",
"検査表①:ｼｰﾄ貼付確認",
"WDQB-F013-020"
]
}
|
{
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "WDQB-F013-020",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPU_BOX組立",
"WorkItems": [
"■1. BOX の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. BOX にLABEL LABEL LABEL を貼付ける"
],
"WorkPoints": [
"筐体上面にﾗﾍﾞﾙを貼付 (貼付方向に注意)",
"EXTENDED UNITがある場合のみLABEL を貼付ける"
],
"Tolks": [],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表BOX :筐体の型式確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表BOX :ﾚﾀｰｺｰﾄﾞ貼付け",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPU_BOX組立",
"WorkItems": [
"■1. BOX の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. BOX にLABEL LABEL LABEL を貼付ける"
],
"WorkPoints": [
"筐体上面にﾗﾍﾞﾙを貼付 (貼付方向に注意)",
"EXTENDED UNITがある場合のみLABEL を貼付ける"
],
"Tolks": [],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表BOX :ﾚﾀｰｺｰﾄﾞ貼付け"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表BOX :筐体の型式確認",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "CPU_BOX組立",
"WorkItems": [
"■1. BOX の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"2. BOX にLABEL LABEL LABEL を貼付ける"
],
"WorkPoints": [
"筐体上面にﾗﾍﾞﾙを貼付 (貼付方向に注意)",
"EXTENDED UNITがある場合のみLABEL を貼付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表BOX :筐体の型式確認",
"検査表BOX :ﾚﾀｰｺｰﾄﾞ貼付け",
"■安全作業"
]
}
|
{
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPUﾎﾞｰﾄﾞ確認(K306)",
"WorkItems": [
"2. 付属のWindowsﾗｲｾﾝｽｼｰﾙのﾗｲｾﾝｽ番号を検査表に記入する",
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"ｼﾘｱﾙNo",
"検査表PCB-COM :ﾗｲｾﾝｽの確認",
"削除",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPUﾎﾞｰﾄﾞ確認(K306)",
"WorkItems": [
"2. 付属のWindowsﾗｲｾﾝｽｼｰﾙのﾗｲｾﾝｽ番号を検査表に記入する",
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :ﾗｲｾﾝｽの確認"
],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"ｼﾘｱﾙNo",
"検査表PCB-COM :型式･検査書ﾁｪｯｸ",
"削除",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPUﾎﾞｰﾄﾞ確認(K306)",
"WorkItems": [
"2. 付属のWindowsﾗｲｾﾝｽｼｰﾙのﾗｲｾﾝｽ番号を検査表に記入する",
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"ｼﾘｱﾙNo",
"検査表PCB-COM :型式･検査書ﾁｪｯｸ",
"検査表PCB-COM :ﾗｲｾﾝｽの確認",
"削除",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "ﾗｲｾﾝｽ記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾗｲｾﾝｽ番号転記",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "34cN･m",
"WorkName": "CPUﾎﾞｰﾄﾞ設定、取付(K306)",
"WorkItems": [
"★1. ①に②を取付ける",
"★2. ②CPUﾎﾞｰﾄﾞのｶｰﾄﾞｽﾛｯﾄにREMOVABLE-MEMORY を挿入する"
],
"WorkPoints": [
"ｶﾊﾞｰを取外し､ｶｰﾄﾞを挿入後､ｶﾊﾞｰを戻す"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表①:付属品取付",
"検査表①:付属品取付"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"ﾈｼﾞ",
"検査表①:接続確認",
"★静電対策作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "34cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "CPUﾎﾞｰﾄﾞ設定、取付(K306)",
"WorkItems": [
"★1. ①に②を取付ける",
"★2. ②CPUﾎﾞｰﾄﾞのｶｰﾄﾞｽﾛｯﾄにREMOVABLE-MEMORY を挿入する",
"3. 2完成品にCONNECTOR-COVER を取付ける"
],
"WorkPoints": [
"K306",
"挿入方向に注意",
"青ﾏｰｷﾝｸﾞし検査書に記入する事",
"ｶﾊﾞｰを取外し､ｶｰﾄﾞを挿入後､ｶﾊﾞｰを戻す"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表①:接続確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"ｶﾊﾞｰ",
"ﾈｼﾞ",
"検査表①:付属品取付",
"検査表①:付属品取付",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "付属品取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K303、K305)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"締付ﾄﾙｸ 34cN･m",
"K303",
"K305",
"型式",
"ｼﾘｱﾙNo.",
"検査表POWER-SUPPLY :型式･検査書ﾁｪｯｸ",
"★2. ⑤にPOWER-SUPPLY を取付ける",
"検査表POWER-SUPPLY :接続確認",
"■★1. POWER-SUPPLY の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"取付け時CPUﾎﾞｰﾄﾞに擦らないよう注意",
"青ﾏｰｷﾝｸﾞし検査書に記入する事",
"削除",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K303、K305)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"締付ﾄﾙｸ 34cN･m",
"K303",
"K305",
"型式",
"ｼﾘｱﾙNo.",
"検査表POWER-SUPPLY :型式･検査書ﾁｪｯｸ",
"★2. ⑤にPOWER-SUPPLY を取付ける",
"検査表POWER-SUPPLY :接続確認",
"■★1. POWER-SUPPLY の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"取付け時CPUﾎﾞｰﾄﾞに擦らないよう注意",
"青ﾏｰｷﾝｸﾞし検査書に記入する事",
"削除",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "34cN･m",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K303、K305)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"締付ﾄﾙｸ 34cN･m",
"K303",
"K305",
"型式",
"ｼﾘｱﾙNo.",
"検査表POWER-SUPPLY :型式･検査書ﾁｪｯｸ",
"★2. ⑤にPOWER-SUPPLY を取付ける",
"検査表POWER-SUPPLY :接続確認",
"■★1. POWER-SUPPLY の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"取付け時CPUﾎﾞｰﾄﾞに擦らないよう注意",
"青ﾏｰｷﾝｸﾞし検査書に記入する事",
"削除",
"★静電対策作業",
"■安全作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "34cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K302、K304)",
"WorkItems": [
"■★1. POWER-SUPPLY の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. ⑤にPOWER-SUPPLY を取付ける"
],
"WorkPoints": [
"K302",
"K304",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表POWER-SUPPLY :型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"検査表POWER-SUPPLY :接続確認",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K302、K304)",
"WorkItems": [
"■★1. POWER-SUPPLY の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. ⑤にPOWER-SUPPLY を取付ける"
],
"WorkPoints": [
"K302",
"K304",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表POWER-SUPPLY :接続確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"検査表POWER-SUPPLY :型式･検査書ﾁｪｯｸ",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "34cN･m",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K302、K304)",
"WorkItems": [
"■★1. POWER-SUPPLY の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. ⑤にPOWER-SUPPLY を取付ける"
],
"WorkPoints": [
"K302",
"K304",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"検査表POWER-SUPPLY :型式･検査書ﾁｪｯｸ",
"検査表POWER-SUPPLY :接続確認",
"★静電対策作業",
"■安全作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "34cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K307)",
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. PCB-COM のｽｲｯﾁ設定確認",
"5. 4完成品にCONNECTOR-COVER を取付ける",
"★4. ⑤に3.完成品を取付ける",
"★3. 2完成品にPCB-COM 付属品ｺﾈｸﾀを挿し込む"
],
"WorkPoints": [
"K307付属品",
"K307",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :接続確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"PCB-COM 付属品",
"検査表PCB-COM :型式･検査書ﾁｪｯｸ",
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認",
"分岐ｹｰﾌﾞﾙ",
"検査表PCB-COM :分岐ｹｰﾌﾞﾙ接続確認",
"設定:0",
"検査表PCB-COM :付属品取付",
"削除",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K307)",
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. PCB-COM のｽｲｯﾁ設定確認",
"5. 4完成品にCONNECTOR-COVER を取付ける",
"★4. ⑤に3.完成品を取付ける",
"★3. 2完成品にPCB-COM 付属品ｺﾈｸﾀを挿し込む"
],
"WorkPoints": [
"K307付属品",
"K307",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"PCB-COM 付属品",
"検査表PCB-COM :接続確認",
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認",
"分岐ｹｰﾌﾞﾙ",
"検査表PCB-COM :分岐ｹｰﾌﾞﾙ接続確認",
"設定:0",
"検査表PCB-COM :付属品取付",
"削除",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K307)",
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. PCB-COM のｽｲｯﾁ設定確認",
"5. 4完成品にCONNECTOR-COVER を取付ける",
"★4. ⑤に3.完成品を取付ける",
"★3. 2完成品にPCB-COM 付属品ｺﾈｸﾀを挿し込む"
],
"WorkPoints": [
"K307付属品",
"K307",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"PCB-COM 付属品",
"検査表PCB-COM :接続確認",
"検査表PCB-COM :型式･検査書ﾁｪｯｸ",
"分岐ｹｰﾌﾞﾙ",
"検査表PCB-COM :分岐ｹｰﾌﾞﾙ接続確認",
"設定:0",
"検査表PCB-COM :付属品取付",
"削除",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定されている事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K307)",
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. PCB-COM のｽｲｯﾁ設定確認",
"5. 4完成品にCONNECTOR-COVER を取付ける",
"★4. ⑤に3.完成品を取付ける",
"★3. 2完成品にPCB-COM 付属品ｺﾈｸﾀを挿し込む"
],
"WorkPoints": [
"K307付属品",
"K307",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :分岐ｹｰﾌﾞﾙ接続確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"PCB-COM 付属品",
"検査表PCB-COM :接続確認",
"検査表PCB-COM :型式･検査書ﾁｪｯｸ",
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認",
"分岐ｹｰﾌﾞﾙ",
"設定:0",
"検査表PCB-COM :付属品取付",
"削除",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "34cN･m",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K307)",
"WorkItems": [
"5. 4完成品にCONNECTOR-COVER を取付ける",
"★4. ⑤に3.完成品を取付ける"
],
"WorkPoints": [
"K307付属品",
"K307",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :付属品取付"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"PCB-COM 付属品",
"検査表PCB-COM :接続確認",
"分岐ｹｰﾌﾞﾙ",
"★静電対策作業",
"■安全作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "34cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K307)",
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. PCB-COM のｽｲｯﾁ設定確認",
"5. 4完成品にCONNECTOR-COVER を取付ける",
"★4. ⑤に3.完成品を取付ける",
"★3. 2完成品にPCB-COM 付属品ｺﾈｸﾀを挿し込む"
],
"WorkPoints": [
"K307付属品",
"K307",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"PCB-COM 付属品",
"検査表PCB-COM :接続確認",
"検査表PCB-COM :型式･検査書ﾁｪｯｸ",
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認",
"分岐ｹｰﾌﾞﾙ",
"検査表PCB-COM :分岐ｹｰﾌﾞﾙ接続確認",
"設定:0",
"検査表PCB-COM :付属品取付",
"削除",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "付属品取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K308)",
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★3. ⑤にPCB-COM を取付ける",
"★2. PCB-COM のｽｲｯﾁ設定確認"
],
"WorkPoints": [
"青ﾏｰｷﾝｸﾞし検査書に記入する事",
"K308"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"設定:0",
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認",
"検査表PCB-COM :接続確認",
"削除",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K308)",
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★3. ⑤にPCB-COM を取付ける",
"★2. PCB-COM のｽｲｯﾁ設定確認"
],
"WorkPoints": [
"青ﾏｰｷﾝｸﾞし検査書に記入する事",
"K308"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認"
],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"検査表PCB-COM :型式･検査書ﾁｪｯｸ",
"設定:0",
"検査表PCB-COM :接続確認",
"削除",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K308)",
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★3. ⑤にPCB-COM を取付ける",
"★2. PCB-COM のｽｲｯﾁ設定確認"
],
"WorkPoints": [
"青ﾏｰｷﾝｸﾞし検査書に記入する事",
"K308"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :接続確認"
],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"検査表PCB-COM :型式･検査書ﾁｪｯｸ",
"設定:0",
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認",
"削除",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定されている事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "34cN･m",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K308)",
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★3. ⑤にPCB-COM を取付ける",
"★2. PCB-COM のｽｲｯﾁ設定確認"
],
"WorkPoints": [
"青ﾏｰｷﾝｸﾞし検査書に記入する事",
"K308"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認",
"検査表PCB-COM :接続確認",
"削除",
"■安全作業",
"★静電対策作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "34cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K309)",
"WorkItems": [
"★2. PCB-COM のｽｲｯﾁ設定確認",
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★3. ⑤にPCB-COM を取付ける"
],
"WorkPoints": [
"K309",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"設定:0",
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認",
"検査表PCB-COM :接続確認",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K309)",
"WorkItems": [
"★2. PCB-COM のｽｲｯﾁ設定確認",
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★3. ⑤にPCB-COM を取付ける"
],
"WorkPoints": [
"K309",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"設定:0",
"検査表PCB-COM :型式･検査書ﾁｪｯｸ",
"検査表PCB-COM :接続確認",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K309)",
"WorkItems": [
"★2. PCB-COM のｽｲｯﾁ設定確認",
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★3. ⑤にPCB-COM を取付ける"
],
"WorkPoints": [
"K309",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :接続確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"設定:0",
"検査表PCB-COM :型式･検査書ﾁｪｯｸ",
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定されている事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "34cN･m",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K309)",
"WorkItems": [
"★2. PCB-COM のｽｲｯﾁ設定確認",
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★3. ⑤にPCB-COM を取付ける"
],
"WorkPoints": [
"K309",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認",
"検査表PCB-COM :接続確認",
"★静電対策作業",
"■安全作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "34cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K310-K314)",
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する(K310-K314)",
"★2. PCB-COM のｽｲｯﾁ､ｼﾞｬﾝﾊﾟｰ設定確認(K310-K314)",
"★3. ⑤にPCB-COM を取付ける(K310-K314)"
],
"WorkPoints": [
"K310",
"K311",
"K313",
"K314",
"K312",
"ｼﾞｬﾝﾊﾟｰが無いことを確認(K310-K314)",
"青ﾏｰｷﾝｸﾞし検査書に記入する事",
"取付け時､ｵﾚﾝｼﾞ色のｺﾞﾑは外す"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"-K310用",
"-K311用",
"-K312用",
"-K313用",
"-K314用",
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認",
"検査表PCB-COM :接続確認",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K310-K314)",
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する(K310-K314)",
"★2. PCB-COM のｽｲｯﾁ､ｼﾞｬﾝﾊﾟｰ設定確認(K310-K314)",
"★3. ⑤にPCB-COM を取付ける(K310-K314)"
],
"WorkPoints": [
"K310",
"K311",
"K313",
"K314",
"K312",
"ｼﾞｬﾝﾊﾟｰが無いことを確認(K310-K314)",
"青ﾏｰｷﾝｸﾞし検査書に記入する事",
"取付け時､ｵﾚﾝｼﾞ色のｺﾞﾑは外す"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"-K310用",
"-K311用",
"-K312用",
"-K313用",
"-K314用",
"検査表PCB-COM :型式･検査書ﾁｪｯｸ",
"検査表PCB-COM :接続確認",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K310-K314)",
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する(K310-K314)",
"★2. PCB-COM のｽｲｯﾁ､ｼﾞｬﾝﾊﾟｰ設定確認(K310-K314)",
"★3. ⑤にPCB-COM を取付ける(K310-K314)"
],
"WorkPoints": [
"K310",
"K311",
"K313",
"K314",
"K312",
"ｼﾞｬﾝﾊﾟｰが無いことを確認(K310-K314)",
"青ﾏｰｷﾝｸﾞし検査書に記入する事",
"取付け時､ｵﾚﾝｼﾞ色のｺﾞﾑは外す"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :接続確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"-K310用",
"-K311用",
"-K312用",
"-K313用",
"-K314用",
"検査表PCB-COM :型式･検査書ﾁｪｯｸ",
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定されている事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "34cN･m",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K310-K314)",
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する(K310-K314)",
"★2. PCB-COM のｽｲｯﾁ､ｼﾞｬﾝﾊﾟｰ設定確認(K310-K314)",
"★3. ⑤にPCB-COM を取付ける(K310-K314)"
],
"WorkPoints": [
"K310",
"K311",
"K313",
"K314",
"K312",
"ｼﾞｬﾝﾊﾟｰが無いことを確認(K310-K314)",
"青ﾏｰｷﾝｸﾞし検査書に記入する事",
"取付け時､ｵﾚﾝｼﾞ色のｺﾞﾑは外す"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認",
"検査表PCB-COM :接続確認",
"★静電対策作業",
"■安全作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "34cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K315)",
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. PCB-COM のｽｲｯﾁ設定確認",
"★3. ⑤にPCB-COM を取付ける"
],
"WorkPoints": [
"K315",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"設定:0",
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認",
"検査表PCB-COM :接続確認",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K315)",
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. PCB-COM のｽｲｯﾁ設定確認",
"★3. ⑤にPCB-COM を取付ける"
],
"WorkPoints": [
"K315",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"設定:0",
"検査表PCB-COM :型式･検査書ﾁｪｯｸ",
"検査表PCB-COM :接続確認",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K315)",
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. PCB-COM のｽｲｯﾁ設定確認",
"★3. ⑤にPCB-COM を取付ける"
],
"WorkPoints": [
"K315",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :接続確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"設定:0",
"検査表PCB-COM :型式･検査書ﾁｪｯｸ",
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定されている事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "34cN･m",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K315)",
"WorkItems": [
"★3. ⑤にPCB-COM を取付ける"
],
"WorkPoints": [
"K315",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"検査表PCB-COM :接続確認",
"★静電対策作業",
"■安全作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "34cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K316)",
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. PCB-COM のｽｲｯﾁ設定確認",
"★3. ⑤にPCB-COM を取付ける"
],
"WorkPoints": [
"K316",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"設定:0",
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認",
"検査表PCB-COM :接続確認",
"削除",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾎﾞｰﾄﾞ設定、取付(K316)",
"WorkItems": [
"■★1. PCB-COM の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"★2. PCB-COM のｽｲｯﾁ設定確認",
"★3. ⑤にPCB-COM を取付ける"
],
"WorkPoints": [
"K316",
"青ﾏｰｷﾝｸﾞし検査書に記入する事"
],
"Tolks": [
"締付ﾄﾙｸ 34cN･m"
],
"InspectionNo": "GWCZ-E013-168",
"InspectionItems": [
"検査表PCB-COM :基板ｼﾞｬﾝﾊﾟｰ設定確認"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"設定:0",
"検査表PCB-COM :型式･検査書ﾁｪｯｸ",
"検査表PCB-COM :接続確認",
"削除",
"GWCZ-E013-168"
]
}
|
{
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "GWCZ-E013-168",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
}
|
information_extraction
|
0
| null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.