input stringclasses 1 value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "上側前面扉取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"矢印方向に当付け固定"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "平面調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5040",
"WorkName": "内臓水準器ﾚﾍﾞﾙ出し調整",
"WorkItems": [
"1. 引き出部の水準を確認"
],
"WorkPoints": [
"X･Y方向: 0.05mm/m以内",
"X･Y方向: 0.05mm/m以内",
"0.02mm/目盛",
"最終工程で確認の為､調整のみ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5040",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "水準器",
"Size": "0.02㎜/目盛",
"ToolOther": "",
"WorkName": "内臓水準器ﾚﾍﾞﾙ出し調整",
"WorkItems": [
"1. 引き出部の水準を確認"
],
"WorkPoints": [
"X･Y方向: 0.05mm/m以内",
"X･Y方向: 0.05mm/m以内",
"0.02mm/目盛",
"最終工程で確認の為､調整のみ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "ﾚﾍﾞﾙ調整",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "X/Y方向0.05㎜/m以内",
"Method": "水準器",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "内臓水準器ﾚﾍﾞﾙ出し調整",
"WorkItems": [
"2. 内蔵水準器の気泡調整を行う"
],
"WorkPoints": [
"内蔵水準器 '0' に調整",
"長い線の間に気泡"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｶﾊﾞｰ用SWﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①に②SPACER をBOLT WASHER で取付",
"2. 1完成品のｺﾈｸﾀを接続する"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄとの隙間:1.8㎜ (下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｺﾈｸﾀ接続確認",
"1.8㎜",
"S02P/R"
]
} | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "1.8㎜",
"ToolOther": "",
"WorkName": "ｶﾊﾞｰ用SWﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①に②SPACER をBOLT WASHER で取付",
"2. 1完成品のｺﾈｸﾀを接続する"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄとの隙間:1.8㎜ (下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｺﾈｸﾀ接続確認",
"1.8㎜",
"S02P/R"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "1.8㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾊﾞｰ用SWﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①に②SPACER をBOLT WASHER で取付",
"2. 1完成品のｺﾈｸﾀを接続する"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄとの隙間:1.8㎜ (下図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "WETE-G002-D33",
"InspectionItems": [
"検査表①:ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"1.8㎜",
"S02P/R",
"WETE-G002-D33"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D33",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "補給完了SWﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"傾きがないように取付"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(左側面前側)",
"WorkItems": [
"1. CAP にNUT NUT を取付",
"2. FRAME に1完成品を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"A 面",
"B 面",
"C 面",
"D 面",
"A面",
"B面",
"C面",
"D面",
"寸法は丸穴ｾﾝﾀｰまでの距離(mm)",
"A面",
"B面",
"C面",
"D面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"下面",
"上面",
"下面",
"上面",
"M6",
"M8"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(左側面後側)",
"WorkItems": [
"1. CAP にNUT NUT を取付",
"2. FRAME に1完成品を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"A面",
"B面",
"C面",
"D面",
"A面",
"B面",
"C面",
"D面",
"寸法は丸穴ｾﾝﾀｰまでの距離(mm)",
"A面",
"B面",
"C面",
"D面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"下面",
"上面",
"下面",
"上面",
"M6",
"M8"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(左側面上_1)",
"WorkItems": [
"1. CAP にNUT NUT NUT を取付",
"2. FRAME に1完成品を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"A面",
"B面",
"C面",
"D面",
"A面",
"寸法は丸穴ｾﾝﾀｰまでの距離(mm)",
"A面",
"B面",
"C面",
"D面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"前側",
"後側",
"後側",
"M5",
"前側",
"M6",
"M8"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(左側面上_2)",
"WorkItems": [
"1. CAP にNUT NUT を取付",
"2. ①に1完成品とCABLE-SUPPORT を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"A面",
"B面",
"C面",
"D面",
"前側",
"後側",
"B面",
"1完成品寸法は丸穴ｾﾝﾀｰまでの距離(mm)CABLE-SUPPORT は四角のｾﾝﾀｰまでの距離(mm)",
"後側",
"前側",
"A面",
"B面",
"C面",
"D面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"M6",
"M8"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(左側面上_3,4)",
"WorkItems": [
"1. CAP にNUT NUT を取付",
"2. ①に1完成品を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"A面",
"B面",
"C面",
"D面",
"C面",
"D面",
"1完成品寸法は丸穴ｾﾝﾀｰまでの距離(mm)",
"A面",
"B面",
"C面",
"D面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"前側",
"後側",
"後側",
"前側",
"M6",
"M8"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(左側面下_1,2,3,4)",
"WorkItems": [
"2. FRAME に1完成品を指定寸法に挿入",
"1. CAP にNUT NUT を取付"
],
"WorkPoints": [
"完成",
"A面",
"B面",
"C面",
"D面",
"A面",
"A面",
"B面",
"C面",
"D面",
"B面",
"寸法は丸穴ｾﾝﾀｰまでの距離(mm)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"前側",
"後側",
"後側",
"前側",
"M6",
"M8"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(左側面下_3,4)",
"WorkItems": [
"1. CAP にNUT NUT を取付",
"2. ①に1完成品を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"･1完成品寸法は丸穴ｾﾝﾀｰまでの距離(mm)･前側､後側に注意して1完成品を挿入",
"A面",
"B面",
"C面",
"D面",
"A面",
"B面",
"C面",
"D面",
"C面",
"D面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"M6",
"M8",
"前側",
"後側",
"後側",
"前側"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(右側面前側)",
"WorkItems": [
"1. CAP にNUT NUT を取付",
"2. FRAME に1完成品とCABLE-SUPPORT を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"A 面",
"B 面",
"C 面",
"D 面",
"A面",
"B面",
"C面",
"D面",
"寸法は丸穴ｾﾝﾀｰまでの距離(mm)",
"A面",
"B面",
"C面",
"D面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"下面",
"上面",
"下面",
"上面",
"M6",
"M8"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(右側面後側)",
"WorkItems": [
"1. ④に②③を取付",
"2. ①に1完成品を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"A面",
"B面",
"C面",
"D面",
"A面",
"B面",
"C面",
"D面",
"寸法は丸穴ｾﾝﾀｰまでの距離(mm)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"下側",
"上側",
"下側",
"上側",
"M6",
"M8",
"上側",
"A面",
"A面",
"下側",
"後側"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(右側面上_1,2,3,4)",
"WorkItems": [
"1. CAP にNUT NUT NUT を取付",
"2. FRAME に1完成品を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"A面",
"B面",
"寸法は丸穴ｾﾝﾀｰまでの距離(mm)",
"A面",
"B面",
"C面",
"D面",
"A面",
"B面",
"C面",
"D面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"後側",
"後側",
"M5",
"前側",
"M6",
"M8",
"前側",
"上面"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(右側面上_3,4)",
"WorkItems": [
"1. CAP にNUT NUT を取付",
"2. ①に1完成品を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"A面",
"B面",
"C面",
"D面",
"前側",
"後側",
"D面",
"1完成品寸法は丸穴ｾﾝﾀｰまでの距離(mm)",
"A面",
"B面",
"C面",
"D面",
"C面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"後側",
"前側",
"上面",
"M6",
"M8"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(右側面上_1,2,3,4)",
"WorkItems": [
"1. CAP にNUT NUT を取付",
"2. FRAME に1完成品を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"A面",
"B面",
"C面",
"D面",
"A面",
"B面",
"1完成品寸法は丸穴ｾﾝﾀｰまでの距離(mm)",
"A面",
"B面",
"C面",
"D面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"前側",
"後側",
"後側",
"前側",
"M6",
"M8",
"上面"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(右側面下_3,4)",
"WorkItems": [
"1. CAP にNUT を取付",
"2. ①に1完成品を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"A面",
"B面",
"C面",
"D面",
"1完成品寸法は丸穴ｾﾝﾀｰまでの距離(mm)",
"A面",
"B面",
"C面",
"D面",
"D面",
"C面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"前側",
"後側",
"後側",
"前側",
"M8",
"上面"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(背面上_1,2,3,4)",
"WorkItems": [
"1. ④に②③を取付",
"2. ①に1完成品を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"1完成品寸法は丸穴ｾﾝﾀｰまでの距離(mm)",
"上側",
"後側",
"A面",
"D面",
"B面",
"C面",
"内側",
"下側",
"A面",
"B面",
"C面",
"D面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"右側",
"左側",
"M6",
"M8",
"A面",
"後側",
"左側",
"右側",
"A面",
"右側",
"左側"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(背面上_3,4)",
"WorkItems": [
"1. CAP にNUT を取付",
"2. ①に1完成品を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"1完成品寸法は丸穴ｾﾝﾀｰまでの距離(mm)",
"D面",
"C面",
"A面",
"B面",
"C面",
"D面",
"A面",
"B面",
"C面",
"D面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"左側",
"右側",
"M8",
"背面",
"左側",
"右側",
"上面"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(背面下_1,2,3,4)",
"WorkItems": [
"1. CAP にNUT NUT を取付",
"2. FRAME に1完成品を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"A面",
"B面",
"C面",
"D面",
"A面",
"B面",
"A面",
"B面",
"C面",
"D面",
"1完成品寸法は丸穴ｾﾝﾀｰまでの距離(mm)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"右側",
"左側",
"M6",
"M8",
"背面",
"左側",
"右側",
"上面"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(背面下_1,2,3,4)",
"WorkItems": [
"1. CAP にNUT を取付",
"2. ①に1完成品を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"1完成品寸法は丸穴ｾﾝﾀｰまでの距離(mm)",
"D面",
"C面",
"A面",
"B面",
"C面",
"D面",
"A面",
"B面",
"C面",
"D面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"左側",
"右側",
"M8",
"背面",
"上面"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(正面上_1,2,3,4)",
"WorkItems": [
"1. CAP にNUT NUT を取付",
"2. FRAME に1完成品を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"A面",
"B面",
"C面",
"D面",
"A面",
"B面",
"1完成品寸法は丸穴ｾﾝﾀｰまでの距離(mm)",
"A面",
"B面",
"C面",
"D面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"右側",
"左側",
"M6",
"M8",
"左側",
"右側",
"上面"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(正面上_1,2,3,4)",
"WorkItems": [
"1. CAP にNUT を取付",
"2. ①に1完成品を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"1完成品寸法は丸穴ｾﾝﾀｰまでの距離(mm)",
"D面",
"C面",
"A面",
"B面",
"C面",
"D面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"左側",
"M8",
"左側",
"右側",
"A面",
"右側",
"後側",
"右側",
"左側",
"B面",
"削除"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(正面上側左)",
"WorkItems": [
"2. FRAME に1完成品を指定寸法に挿入",
"1. CAP にNUT NUT NUT を取付"
],
"WorkPoints": [
"完成",
"A 面",
"B 面",
"C 面",
"D 面",
"A面",
"B面",
"C面",
"A面",
"B面",
"C面",
"D面",
"寸法は丸穴ｾﾝﾀｰまでの距離(mm)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"前側",
"後側",
"前側",
"後側",
"M5",
"M6",
"M8"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(正面上側右)",
"WorkItems": [
"1. CAP にNUT NUT NUT を取付",
"2. FRAME に1完成品とCAP を指定寸法に挿入"
],
"WorkPoints": [
"C面",
"A面",
"A面",
"B面",
"C面",
"D面",
"完成",
"A 面",
"B 面",
"C 面",
"D 面",
"1完成品寸法は丸穴ｾﾝﾀｰまでの距離(mm)",
"D面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"後側",
"前側",
"凸部",
"前側",
"後側",
"M5",
"M6",
"M8"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(正面右側)",
"WorkItems": [
"1. CAP にNUT を取付",
"2. FRAME に1完成品を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"A 面",
"B 面",
"C 面",
"D 面",
"A面",
"B面",
"C面",
"D面",
"寸法は丸穴ｾﾝﾀｰまでの距離(mm)",
"D面",
"C面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"下面",
"上面",
"M8",
"下面",
"上面"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(正面左側)",
"WorkItems": [
"1. CAP にNUT を取付",
"2. FRAME に1完成品とCABLE-SUPPORT を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"A 面",
"B 面",
"C 面",
"D 面",
"A面",
"B面",
"C面",
"D面",
"寸法は丸穴ｾﾝﾀｰまでの距離(mm)",
"D面",
"B面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"下面",
"上面",
"M8",
"下面",
"上面"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "本体部ﾌﾚｰﾑﾅｯﾄ(正面中央)",
"WorkItems": [
"1. CAP にNUT NUT を取付",
"2. FRAME に1完成品を指定寸法に挿入"
],
"WorkPoints": [
"完成",
"A 面",
"B 面",
"C 面",
"D 面",
"A面",
"B面",
"C面",
"D面",
"寸法は丸穴ｾﾝﾀｰまでの距離(mm)",
"A面",
"B面",
"C面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"凸部",
"左側",
"右側",
"M6",
"M8",
"右側",
"左側"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ①",
"WorkItems": [
"1. ①②③④をBRACKET BOLT で取付"
],
"WorkPoints": [
"A矢視",
"線部はすべて隙間無い事",
"定盤上でつら合わせする事",
"E矢視",
"F矢視",
"B･C･D矢視は同様の手順で行う事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"背面",
"正面"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ①",
"WorkItems": [
"1. ①②③④をBRACKET BOLT で取付"
],
"WorkPoints": [
"A矢視",
"線部はすべて隙間無い事",
"定盤上でつら合わせする事",
"E矢視",
"F矢視",
"B･C･D矢視は同様の手順で行う事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"背面",
"正面"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ②",
"WorkItems": [
"1. ①に②③④⑤をBRACKET BOLT で取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上でつら合わせする事",
"A矢視",
"B矢視",
"③④⑤も同様の手順で行う事",
"C矢視"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ②",
"WorkItems": [
"1. ①に②③④⑤をBRACKET BOLT で取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上でつら合わせする事",
"A矢視",
"B矢視",
"③④⑤も同様の手順で行う事",
"C矢視"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ②",
"WorkItems": [
"1. ①に②③④⑤をBRACKET BOLT で取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上でつら合わせする事",
"A矢視",
"B矢視",
"③④⑤も同様の手順で行う事",
"C矢視"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ③",
"WorkItems": [
"1. ①②③をBRACKET BOLT で取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"C矢視",
"D矢視",
"B矢視は同様の手順で行う事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ③",
"WorkItems": [
"1. ①②③をBRACKET BOLT で取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"C矢視",
"D矢視",
"B矢視は同様の手順で行う事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ④",
"WorkItems": [
"1. ①に②をBRACKET BOLT で取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"A矢視",
"B矢視",
"C矢視",
"E,F,Gは同様の手順で行う事",
"定盤上で面合わせする事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ④",
"WorkItems": [
"1. ①に②をBRACKET BOLT で取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"A矢視",
"B矢視",
"C矢視",
"E,F,Gは同様の手順で行う事",
"定盤上で面合わせする事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑤",
"WorkItems": [
"1. ①にPLATE PLATE をBRACKET BRACKET BOLT BOLT NUT BOLT で仮取付"
],
"WorkPoints": [
"A矢視",
"B矢視",
"C矢視",
"仮止め:SD-A042453-030にて本締め"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑤",
"WorkItems": [
"1. ①にPLATE PLATE をBRACKET BRACKET BOLT BOLT NUT BOLT で仮取付"
],
"WorkPoints": [
"A矢視",
"B矢視",
"C矢視",
"仮止め:SD-A042453-030にて本締め"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑥",
"WorkItems": [
"1. ①を本締め"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"A矢視は寸法の位置に従って取付の事",
"上面が定盤に当たっている状態で取付の事",
"B矢視",
"C矢視",
"D矢視"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑥",
"WorkItems": [
"1. ①を本締め"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"A矢視は寸法の位置に従って取付の事",
"上面が定盤に当たっている状態で取付の事",
"B矢視",
"C矢視",
"D矢視"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑥",
"WorkItems": [
"1. ①を本締め"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"A矢視は寸法の位置に従って取付の事",
"上面が定盤に当たっている状態で取付の事",
"B矢視",
"C矢視",
"D矢視"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑥",
"WorkItems": [
"1. ①を本締め"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"A矢視は寸法の位置に従って取付の事",
"上面が定盤に当たっている状態で取付の事",
"B矢視",
"C矢視",
"D矢視"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑦",
"WorkItems": [
"1. ①②にBRACKET BOLT を取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"B矢視",
"C矢視"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑦",
"WorkItems": [
"1. ①②にBRACKET BOLT を取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"B矢視",
"C矢視"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑧",
"WorkItems": [
"1. ①②にBRACKET BOLT を取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"B矢視",
"C矢視",
"A矢視"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑧",
"WorkItems": [
"1. ①②にBRACKET BOLT を取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"B矢視",
"C矢視",
"A矢視"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑨",
"WorkItems": [
"1. ①②に③をBRACKET BOLT で取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"C矢視",
"D矢視",
"B矢視は同様の手順で行う事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑨",
"WorkItems": [
"1. ①②に③をBRACKET BOLT で取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"C矢視",
"D矢視",
"B矢視は同様の手順で行う事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑨",
"WorkItems": [
"1. ①②に③をBRACKET BOLT で取付"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"C矢視",
"D矢視",
"B矢視は同様の手順で行う事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑩",
"WorkItems": [
"1. ①②をBRACKET BRACKET BOLT で仮取付"
],
"WorkPoints": [
"A矢視",
"B矢視",
"A･B矢視の反対側も同様に仮取付する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"仮止め:SD-A042453-035にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑪",
"WorkItems": [
"1. ①を本締め"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"B矢視",
"C矢視",
"A矢視は寸法の位置に従って取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"後側",
"左側",
"右側"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.10㎜",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑪",
"WorkItems": [
"1. ①を本締め"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"B矢視",
"C矢視",
"A矢視は寸法の位置に従って取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"後側",
"左側",
"右側"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "本体ﾌﾚｰﾑﾄﾞｯｷﾝｸﾞ⑪",
"WorkItems": [
"1. ①を本締め"
],
"WorkPoints": [
"線部はすべて隙間無い事",
"定盤上で面合わせする事",
"A矢視",
"B矢視",
"C矢視",
"A矢視は寸法の位置に従って取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"後側",
"左側",
"右側"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｷｬｽﾀｰ部組立",
"WorkItems": [
"2. PLATE PLATE (4個)に1完成品(4個)を仮付けする",
"◆1. ADJUST-BOLT (4個)ﾎﾞﾙﾄﾈｼﾞ部にｸﾞﾘｰｽを塗布する",
"3. 2完成品にCASTER をNUT WASHER で取付ける"
],
"WorkPoints": [
"図の通り対称のものを2個作製する",
"対称のものを2個ずつ作製する",
"仮固定",
"本体ﾄﾞｯｷﾝｸﾞ工程 SD-A042453-231にて本締め",
"他にｸﾞﾘｰｽが付かないように塗布する事",
"145±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ容器",
"10㎜程度",
"ｸﾞﾘｰｽを塗布する(LCG100)",
"㉙薄型ｽﾊﾟﾅで固定"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｸﾞﾘｰｽ容器10㎜程度",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｷｬｽﾀｰ部組立",
"WorkItems": [],
"WorkPoints": [
"仮固定",
"本体ﾄﾞｯｷﾝｸﾞ工程 SD-A042453-231にて本締め",
"145±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽを塗布する(LCG100)",
"㉙薄型ｽﾊﾟﾅで固定",
"◆作業者安全作業"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "ｷｬｽﾀｰ部組立",
"WorkItems": [
"2. PLATE PLATE (4個)に1完成品(4個)を仮付けする",
"◆1. ADJUST-BOLT (4個)ﾎﾞﾙﾄﾈｼﾞ部にｸﾞﾘｰｽを塗布する",
"3. 2完成品にCASTER をNUT WASHER で取付ける"
],
"WorkPoints": [
"図の通り対称のものを2個作製する",
"対称のものを2個ずつ作製する",
"仮固定",
"本体ﾄﾞｯｷﾝｸﾞ工程 SD-A042453-231にて本締め",
"他にｸﾞﾘｰｽが付かないように塗布する事",
"145±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ容器",
"10㎜程度",
"ｸﾞﾘｰｽを塗布する(LCG100)",
"㉙薄型ｽﾊﾟﾅで固定"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "ｷｬｽﾀｰ部取付",
"WorkItems": [
"1. ①に②③(4個)をBOLT で取付ける"
],
"WorkPoints": [
"ｷｬｽﾀｰﾌﾟﾚｰﾄがﾌﾚｰﾑからはみ出さず面一で取付",
"②③の違い",
"K036-1",
"K036-2",
"②③の取付位置に注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"A底面から",
"A矢視",
"前側",
"左側",
"右側",
"前側",
"後側",
"上面",
"右側"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀｰﾌﾞﾗｹｯﾄ組立(銘板貼付け)",
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"下記指示寸法位置に㉖㉗で脱脂後貼付",
"ﾌﾞﾗｹｯﾄ右面から119±1㎜",
"ﾌﾞﾗｹｯﾄ上面から40±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀｰﾌﾞﾗｹｯﾄ組立(銘板貼付け)",
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"下記指示寸法位置に㉖㉗で脱脂後貼付",
"ﾌﾞﾗｹｯﾄ右面から119±1㎜",
"ﾌﾞﾗｹｯﾄ上面から40±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀｰ部組立",
"WorkItems": [
"1. REGULATOR の付属のｹﾞｰｼﾞの目盛を0.4~0.5に設定する",
"2. 1完成品をREGULATOR 本体に取付ける",
"3. 2完成品にCOUPLER とJOINT を取付ける"
],
"WorkPoints": [
"OUT側",
"出代41.5±1㎜",
"目視で平行にする",
"ｹﾞｰｼﾞの取付に注意する事",
"IN側",
"出代:32±1.0㎜",
"出代38±1.0㎜",
"継手の取付に注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法通り取付け出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀｰﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. ②の穴(1ヵ所)に③を指定寸法にｶｯﾄし貼付ける",
"2. 1完成品に①を⑯⑰で取付ける"
],
"WorkPoints": [
"①の取付位置に注意する事",
"③120±1.0㎜",
"GEE144F-A-C (両面ﾃｰﾌﾟ付き)"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾒｲﾝﾚｷﾞｭﾚｰﾀｰﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. ②の穴(1ヵ所)に③を指定寸法にｶｯﾄし貼付ける",
"2. 1完成品に①を⑯⑰で取付ける"
],
"WorkPoints": [
"①の取付位置に注意する事",
"③120±1.0㎜",
"GEE144F-A-C (両面ﾃｰﾌﾟ付き)"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ、Ⅹ軸ﾚｷﾞｭﾚｰﾀｰ組立",
"WorkItems": [],
"WorkPoints": [
"目視で平行になる様取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法通り取付け出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "1.5N･m",
"WorkName": "ﾌｨｰﾀﾞ、Ⅹ軸ﾚｷﾞｭﾚｰﾀｰ組立",
"WorkItems": [],
"WorkPoints": [
"目視で平行になる様取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ、Ⅹ軸ﾚｷﾞｭﾚｰﾀｰﾌﾞﾗｹｯﾄ組立(銘板貼付け)",
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"下記指示寸法位置に㉖㉗で脱脂後指定銘板を貼付ける",
"ﾌﾞﾗｹｯﾄ上面から80±1㎜",
"ﾌﾞﾗｹｯﾄ下面から10±1㎜",
"ﾌﾞﾗｹｯﾄ右面から15±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ、Ⅹ軸ﾚｷﾞｭﾚｰﾀｰﾌﾞﾗｹｯﾄ組立(銘板貼付け)",
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"下記指示寸法位置に㉖㉗で脱脂後指定銘板を貼付ける",
"ﾌﾞﾗｹｯﾄ上面から80±1㎜",
"ﾌﾞﾗｹｯﾄ下面から10±1㎜",
"ﾌﾞﾗｹｯﾄ右面から15±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "2m",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ、Ⅹ軸ﾚｷﾞｭﾚｰﾀｰﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"1. BRACKET に①を②で取付ける(2ヵ所)"
],
"WorkPoints": [
"目視で平行になる様取付ける",
"･①の傾きに注意する事･②の表裏に注意する事",
"L=1100㎜ ×2",
"内側",
"IN側",
"IN側",
"外側",
"ﾒｲﾝｴｱｰﾚｷﾞｭﾚｰﾀ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾛｰｽｲｯﾁﾌﾞﾗｹｯﾄ組立(銘板貼付け)",
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"下記指示位置にLABEL を貼付ける",
"ﾌﾞﾗｹｯﾄ下面から47±1㎜",
"ﾌﾞﾗｹｯﾄ左面から15±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾛｰｽｲｯﾁﾌﾞﾗｹｯﾄ組立(銘板貼付け)",
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"下記指示位置にLABEL を貼付ける",
"ﾌﾞﾗｹｯﾄ下面から47±1㎜",
"ﾌﾞﾗｹｯﾄ左面から15±1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "42cN･m",
"WorkName": "ﾌﾛｰｽｲｯﾁﾌﾞﾗｹｯﾄ組立",
"WorkItems": [],
"WorkPoints": [
"SWITCH 付属品を使用し組立",
"SWITCH のﾌﾞﾗｹｯﾄの向きに注意する事",
"1完成品の向きに注意する事",
"SW側を右向きで取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "42cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾌﾛｰｽｲｯﾁﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"2. 1完成品を②BOLT WASHER で取付ける",
"3. 2完成品にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"BRACKET の向きに注意する事",
"SWは上方向に当付け"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾌﾛｰｽｲｯﾁﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"2. 1完成品を②BOLT WASHER で取付ける",
"3. 2完成品にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"BRACKET の向きに注意する事",
"SWは上方向に当付け"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ﾌﾛｰｽｲｯﾁﾌﾞﾗｹｯﾄ組立(配線、配管接続)",
"WorkItems": [
"2. 1完成品を①に接続する",
"1. ②を指示寸法にｶｯﾄする",
"3. 2完成品に⑥ﾀｸﾞ取付を行う"
],
"WorkPoints": [
"L=300㎜ ×1L=1000㎜ ×1",
"300㎜",
"・⑥の位置に注意する事・ラベルは㉘で脱脂後貼付る",
"⑥は被覆端面合わせで取付ける",
"配管先端に名称を記入する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾌｨｰﾀﾞｰ供給圧(F OUT側)"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "8㎜",
"ToolOther": "1.2N･m",
"WorkName": "ｴｱｰﾌﾞﾛｯｸ組立",
"WorkItems": [
"1. AIR-BLOCK にCOUPLER PLUG JOINT 取付ける"
],
"WorkPoints": [
"COUPLER PLUG JOINT の取付に注意する",
"12±0.5㎜",
"1.0±0.5㎜",
"PLUG の締め込み量",
"JOINT の締め込み量",
"COUPLER 20ｹ取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｴｱｰﾌﾞﾛｯｸ組立",
"WorkItems": [
"1. AIR-BLOCK にCOUPLER PLUG JOINT 取付ける"
],
"WorkPoints": [
"COUPLER PLUG JOINT の取付に注意する",
"12±0.5㎜",
"1.0±0.5㎜",
"PLUG の締め込み量",
"JOINT の締め込み量",
"COUPLER 20ｹ取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｴｱｰﾌﾞﾛｯｸ組立(ｶﾞｲﾄﾞ取付)",
"WorkItems": [
"1. ①をBRACKET にBOLT WASHER で取付ける",
"2. 1完成品にGUIDE をBOLT で取付ける"
],
"WorkPoints": [
"①の向きに注意する事",
"切り欠き",
"折り曲げ",
"押し当てで取付ける",
"GUIDE の取付けに注意する事",
"押し当てで取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｴｱｰﾌﾞﾛｯｸ組立(ｶﾞｲﾄﾞ取付)",
"WorkItems": [
"1. ①をBRACKET にBOLT WASHER で取付ける",
"2. 1完成品にGUIDE をBOLT で取付ける"
],
"WorkPoints": [
"①の向きに注意する事",
"切り欠き",
"折り曲げ",
"押し当てで取付ける",
"GUIDE の取付けに注意する事",
"押し当てで取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｴｱｰﾌﾞﾛｯｸ組立(ｻｲﾄﾞﾌﾟﾚｰﾄ取付)",
"WorkItems": [
"1. PLATE へ①SPACER をBOLT WASHER で取付ける"
],
"WorkPoints": [
"①の取付けに注意する事",
"ｶﾌﾟﾗ",
"折り曲げ",
"①とPLATE を面一固定する事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(銘板貼付け)",
"WorkItems": [
"1. ①にLABEL LABEL を貼付ける"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄ下面から10±1㎜",
"ﾌﾞﾗｹｯﾄ右面から10±1㎜",
"ﾌﾞﾗｹｯﾄ右面から75±1㎜",
"ﾌﾞﾗｹｯﾄ下面から30±1㎜",
"下記指示寸法位置に㉖㉗で脱脂後貼付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(銘板貼付け)",
"WorkItems": [
"1. ①にLABEL LABEL を貼付ける"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄ下面から10±1㎜",
"ﾌﾞﾗｹｯﾄ右面から10±1㎜",
"ﾌﾞﾗｹｯﾄ右面から75±1㎜",
"ﾌﾞﾗｹｯﾄ下面から30±1㎜",
"下記指示寸法位置に㉖㉗で脱脂後貼付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "60cN･m",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(ｺﾈｸﾀ取付)",
"WorkItems": [
"1. BRACKET へCONNECTOR をSCREW で取付ける(20ｶ所)"
],
"WorkPoints": [
"CONNECTOR の取付けに注意する事",
"左に押し当てで固定する事",
"折り曲げ",
"写真の向きで取付ける",
"CONNECTOR の向きに注意しBRACKET の穴に入れ取付ける",
"裏から見た写真",
"凸側"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"正面",
"正面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(ﾋﾟﾝ取付)",
"WorkItems": [
"▲2. 1完成品に①を乗せてﾋﾟﾝを⑯で固定する",
"1. ㉙へ②を挿入する（20カ所）"
],
"WorkPoints": [
"全てﾋﾟﾝの溝が治具に入った事を確認し､①と治具との隙間無いことを確認後固定する",
"②の溝に注意する事",
"横から写真",
"全てﾋﾟﾝの溝が治具に入った事を確認",
"⑯固定時はピンに㉘を塗布して固定する"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"接着剤塗布 ｺﾞﾏ粒:1"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(ﾋﾟﾝ取付)",
"WorkItems": [
"▲2. 1完成品に①を乗せてﾋﾟﾝを⑯で固定する",
"1. ㉙へ②を挿入する（20カ所）"
],
"WorkPoints": [
"②の溝に注意する事",
"⑯固定時はピンに㉘を塗布して固定する"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"▲特殊作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝ位置合わせ治具",
"Size": "",
"ToolOther": "FM-6555",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(ﾋﾟﾝ取付)",
"WorkItems": [
"▲2. 1完成品に①を乗せてﾋﾟﾝを⑯で固定する",
"1. ㉙へ②を挿入する（20カ所）",
"▲2. 1完成品に①を乗せてﾋﾟﾝを⑯で固定する",
"1. ㉙へ②を挿入する（20カ所）"
],
"WorkPoints": [
"②の溝に注意する事",
"⑯固定時はピンに㉘を塗布して固定する",
"②の溝に注意する事",
"⑯固定時はピンに㉘を塗布して固定する"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"▲特殊作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6555",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "1.5N･m",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(ｽﾍﾟｰｻｰ取付)",
"WorkItems": [
"1. ①へSPACER をBOLT WASHER で取付(6ｶ所)",
"2. 1完成品へSPACER をBOLT WASHER で取付(5ｶ所)"
],
"WorkPoints": [
"SPACER 取付位置に注意する事",
"SPACER 取付位置に注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(ｽﾍﾟｰｻｰ取付)",
"WorkItems": [
"1. ①へSPACER をBOLT WASHER で取付(6ｶ所)",
"2. 1完成品へSPACER をBOLT WASHER で取付(5ｶ所)"
],
"WorkPoints": [
"SPACER 取付位置に注意する事",
"SPACER 取付位置に注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(基板取付)",
"WorkItems": [
"■1. 20-ROW FEEDER CART BOARD の型式を検査表で確認し､ｼﾘｱ№を検査表に記載する事",
"★2. ①に20-ROW FEEDER CART BOARD をSCREW で取付(6ｶ所)"
],
"WorkPoints": [
"図の右手前に大きいｺﾈｸﾀがくる事",
"20-ROW FEEDER CART BOARD 取付方向に注意する事",
"検査表と型式が一致する事､ｼﾘｱﾙ№が記載されている事"
],
"Tolks": [
"締付ﾄﾙｸ 90cN･m"
],
"InspectionNo": "WEWD-F013-051",
"InspectionItems": [
"検査表①:型式ﾁｪｯｸ"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"WEWD-F013-051"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEWD-F013-051",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "90cN･m",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(基板取付)",
"WorkItems": [
"■1. 20-ROW FEEDER CART BOARD の型式を検査表で確認し､ｼﾘｱ№を検査表に記載する事",
"★2. ①に20-ROW FEEDER CART BOARD をSCREW で取付(6ｶ所)"
],
"WorkPoints": [
"図の右手前に大きいｺﾈｸﾀがくる事",
"20-ROW FEEDER CART BOARD 取付方向に注意する事",
"検査表と型式が一致する事､ｼﾘｱﾙ№が記載されている事"
],
"Tolks": [
"締付ﾄﾙｸ 90cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"検査表①:型式ﾁｪｯｸ",
"★静電対策作業",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(配線接続)",
"WorkItems": [
"1. CABLE にLABEL を取付",
"★2. ①に1完成品を接続する(20ｶ所)"
],
"WorkPoints": [
"黒いｺﾈｸﾀ側にﾗﾍﾞﾙﾀｲ側を接続する",
"LABEL は20種類あり(負荷ﾗﾍﾞﾙ:CN41/SLOT1~CN60/SLOT20)",
"CN60/SLOT20のｺﾈｸﾀ接続する事(接続番号に注意する事)",
"2完成品の接続に注意する事"
],
"Tolks": [],
"InspectionNo": "WEWD-F013-051",
"InspectionItems": [
"検査表①:ｺﾈｸﾀ接続"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"WEWD-F013-051"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEWD-F013-051",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(ｶﾊﾞｰ取付)",
"WorkItems": [
"2. 1完成品を①に⑯⑰で取付",
"1. ③を各指示寸法にｶｯﾄし､②に取付"
],
"WorkPoints": [
"210㎜を貼付ける",
"395㎜を貼付ける",
"1完成品取付時配線が噛み込み､ｴｯﾁﾞ干渉無き事",
"L=210±1㎜×1､L=395±1㎜×1"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(ｶﾊﾞｰ取付)",
"WorkItems": [],
"WorkPoints": [
"ﾄﾘﾑを奥まで押し込んで貼付ける",
"配線をｴｯﾁﾞ部に干渉させ無い事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ基板ﾌﾞﾗｹｯﾄ組立(配線処理)",
"WorkItems": [
"1. ①の配線を㉖で固定する"
],
"WorkPoints": [
"4ｶ所固定(5本/SET)",
"配線の干渉無き事",
"配線をｴｯﾁﾞ部に干渉させ無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞﾍﾞｰｽﾌﾟﾚｰﾄ組立(ﾋﾟﾝ圧入)",
"WorkItems": [
"2. 1完成品にPIN を(2個)圧入する",
"3. 2完成品にPIN を(6個)圧入する",
"1. PLATE にPIN を(3個)圧入する",
"2. 1完成品にPIN を(2個)圧入する",
"3. 2完成品にPIN を(6個)圧入する",
"1. PLATE にPIN を(3個)圧入する",
"2. 1完成品にPIN を(2個)圧入する",
"3. 2完成品にPIN を(6個)圧入する",
"1. PLATE にPIN を(3個)圧入する"
],
"WorkPoints": [
"PIN の出代に注意する事",
"PIN の出代に注意する事",
"出代:3㎜",
"出代:5㎜",
"出代:5㎜",
"出代:5㎜",
"出代:4㎜",
"割の向き",
"PIN の出代に注意する事",
"PIN の出代に注意する事",
"出代:3㎜",
"出代:5㎜",
"出代:5㎜",
"出代:5㎜",
"出代:4㎜",
"割の向き",
"PIN の出代に注意する事",
"PIN の出代に注意する事",
"出代:3㎜",
"出代:5㎜",
"出代:5㎜",
"出代:5㎜",
"出代:4㎜",
"割の向き"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"PLATE 裏面",
"PLATE 表面",
"PLATE 裏面",
"PLATE 表面",
"PLATE 裏面",
"PLATE 表面"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾌｨｰﾀﾞ偏芯ﾋﾟﾝ位置決めﾌﾟﾚｰﾄ組立(ﾋﾟﾝ圧入)",
"WorkItems": [
"2. 1完成品にPLATE をBOLT で取付ける",
"1. PLATE にSPRING-PLATE を(20個)挿入する"
],
"WorkPoints": [
"・PLATE の取付位置に注意する事・㉘ピンゲージがPLATE PLATE 通して固定する事",
"SPRING-PLATE の向きに注意する事",
"割の向きを矢印に向け挿入する事",
"面一に固定する",
"ﾋﾟﾝｹﾞｰｼﾞが通る事を確認する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝｹﾞｰｼﾞ",
"Size": "φ5",
"ToolOther": "",
"WorkName": "ﾌｨｰﾀﾞ偏芯ﾋﾟﾝ位置決めﾌﾟﾚｰﾄ組立(ﾋﾟﾝ圧入)",
"WorkItems": [
"2. 1完成品にPLATE をBOLT で取付ける",
"1. PLATE にSPRING-PLATE を(20個)挿入する"
],
"WorkPoints": [
"・PLATE の取付位置に注意する事・㉘ピンゲージがPLATE PLATE 通して固定する事",
"SPRING-PLATE の向きに注意する事",
"割の向きを矢印に向け挿入する事",
"面一に固定する",
"ﾋﾟﾝｹﾞｰｼﾞが通る事を確認する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "-",
"StdVal": "ﾋﾟﾝｹﾞｰｼﾞが通る事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.