input stringclasses 1 value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP】文字認識ﾍｯﾄﾞｶﾒﾗ取付②",
"WorkItems": [
"■1. ﾍｯﾄﾞｶﾒﾗｹｰﾌﾞﾙ及びLED照明ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [
"LED照明の下面よりも下方向に垂れ下がら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [
"検査表②:18.ﾍｯﾄﾞｶﾒﾗLED照明のｹｰﾌﾞﾙ取付け確認"
],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"検査表①:4.ｺﾈｸﾀ接続確認 1-3.ﾍｯﾄﾞｶﾒﾗLED照明",
"LED照明より配線が下に出無い事",
"B311",
"1K335/6",
"ｵｲﾙﾊﾟﾝと配線が干渉してい無い事",
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "LED照明の下面よりも下方向に垂れ下がら無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "110cN･m",
"WorkName": "【OP】文字認識ﾍｯﾄﾞｶﾒﾗ取付③",
"WorkItems": [
"1. CLIP をBOLT で取付ける"
],
"WorkPoints": [
"OP;高さｾﾝｻ仕様がある場合はCLIP BOLT 取付不要"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"CLIP の取付け方向に注意"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "【OP】文字認識ﾍｯﾄﾞｶﾒﾗ取付④",
"WorkItems": [
"1. CABLE に黄色ﾏｰｷﾝｸﾞをする",
"2. 文字認識ﾍｯﾄﾞｶﾒﾗに1の完成品を接続する",
"3. 配線を引き回し、㉗で固定する",
"1. CABLE に黄色ﾏｰｷﾝｸﾞをする",
"2. 文字認識ﾍｯﾄﾞｶﾒﾗに1の完成品を接続する",
"3. 配線を引き回し、㉗で固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"100mm",
"CN2",
"CN2",
"検査表CABLE :CRC1.ｺﾈｸﾀ接続確認",
"枠から配線を中に入れる",
"黄色ﾏｰｷﾝｸﾞの位置で固定する事",
"ｲﾝｼｭﾛｯｸ頭向き注意",
"100mm",
"CN2",
"CN2",
"検査表CABLE :CRC1.ｺﾈｸﾀ接続確認",
"枠から配線を中に入れる",
"黄色ﾏｰｷﾝｸﾞの位置で固定する事",
"ｲﾝｼｭﾛｯｸ頭向き注意"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP】文字認識ﾍｯﾄﾞｶﾒﾗ取付④",
"WorkItems": [
"1. CABLE に黄色ﾏｰｷﾝｸﾞをする",
"2. 文字認識ﾍｯﾄﾞｶﾒﾗに1の完成品を接続する",
"3. 配線を引き回し、㉗で固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表CABLE :CRC1.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"100mm",
"CN2",
"CN2",
"枠から配線を中に入れる",
"黄色ﾏｰｷﾝｸﾞの位置で固定する事",
"20mm以内で結束する",
"ｲﾝｼｭﾛｯｸ頭向き注意",
"ｽﾄｯﾊﾟｰより配線が出無い事",
"WETE-G002-A03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "【OP】高さｾﾝｻｰ取付①",
"WorkItems": [
"1. CLIP をBOLT で取付ける",
"2. CABLE-SUPPORT SPACER をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 110cN･m",
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"CLIP の取付け方向に注意",
"ﾌﾛﾝﾄ",
"CABLE-SUPPORT の取付け方向に注意",
"ﾘｱ",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "【OP】高さｾﾝｻｰ取付②",
"WorkItems": [
"1. ①をBOLT WASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表①:HS1.高さｾﾝｻﾕﾆｯﾄの取付(取付確認)"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ﾌﾟﾚｰﾄの正面から固定する",
"ﾌﾟﾚｰﾄの裏面から固定する"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP】高さｾﾝｻｰ取付③",
"WorkItems": [
"1. 配線を引き回し、㉖㉗で固定する（フェライトコアから固定）",
"2. 配線を引き回し、㉗で固定する"
],
"WorkPoints": [
"ﾌｪﾗｲﾄｺｱの中央をﾏｳﾝﾄに合わせて固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"枠から配線を中に入れる",
"20mm以内で結束する",
"ｲﾝｼｭﾛｯｸ頭向き注意",
"ｽﾄｯﾊﾟｰより配線が出無い事",
"ﾌｪﾗｲﾄｺｱ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ配線用ﾏｳﾝﾄ取付",
"WorkItems": [
"1. YﾌﾚｰﾑへCABLE-SUPPORT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"8箇所",
"取付方向",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ受けﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける",
"2. ㉘（位置決め用ダミーネジ）を取り外す"
],
"WorkPoints": [
"㉘のダミーネジを入れてから押し付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"㉘（位置決め用ダミーネジ）を入れる",
"押し付け",
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付①",
"WorkItems": [
"1. ①へNUT-BLOCK NUT-BLOCK BRACKET をBOLT WASHER BOLT WASHER で仮取付けする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"Y軸ﾍﾞｱ",
"X軸ﾍﾞｱ",
"取付け箇所注意"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜ﾎﾞｰﾙﾎﾟｲﾝﾄ",
"ToolOther": "1.9N･m",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付②",
"WorkItems": [
"1. ①のY軸ﾍﾞｱをBOLT WASHER BOLT で取付ける"
],
"WorkPoints": [
"仮締めﾈｼﾞを本締めする"
],
"Tolks": [
"締付ﾄﾙｸ 1.9N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"仮締め⇒本締め",
"BOLT 及び仮締めﾈｼﾞは均等に締め付ける事",
"検査表①:7.組立時調整",
"BOLT の下（固定子上）に㉘を敷く事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.9N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付②",
"WorkItems": [
"1. ①のY軸ﾍﾞｱをBOLT WASHER BOLT で取付ける"
],
"WorkPoints": [
"仮締めﾈｼﾞを本締めする"
],
"Tolks": [
"締付ﾄﾙｸ 1.9N･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:7.組立時調整"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"仮締め⇒本締め",
"BOLT 及び仮締めﾈｼﾞは均等に締め付ける事",
"BOLT の下（固定子上）に㉘を敷く事",
"WETE-G002-D08"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸固定子簡易保護ｶﾊﾞｰ",
"Size": "",
"ToolOther": "FM-3050",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付②",
"WorkItems": [
"1. ①のY軸ﾍﾞｱをBOLT WASHER BOLT で取付ける"
],
"WorkPoints": [
"仮締めﾈｼﾞを本締めする"
],
"Tolks": [
"締付ﾄﾙｸ 1.9N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"仮締め⇒本締め",
"BOLT 及び仮締めﾈｼﾞは均等に締め付ける事",
"検査表①:7.組立時調整",
"BOLT の下（固定子上）に㉘を敷く事"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3050",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.9N･m",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付③",
"WorkItems": [
"1. X軸ﾍﾞｱを反時計回りに反転し､X軸ﾍﾞｱ受けに乗せる",
"2. X軸ﾍﾞｱをBOLT BOLT WASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"仮締めﾈｼﾞを本締めする"
],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m",
"締付ﾄﾙｸ 1.9N･m",
"締付ﾄﾙｸ 1.9N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"仮締め⇒本締め",
"BOLT BOLT 及び仮締めﾈｼﾞは均等に締め付ける事",
"反時計回りに反転する",
"Y軸ﾍﾞｱ",
"X軸ﾍﾞｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.9N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.94N･m",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付③",
"WorkItems": [
"1. X軸ﾍﾞｱを反時計回りに反転し､X軸ﾍﾞｱ受けに乗せる",
"2. X軸ﾍﾞｱをBOLT BOLT WASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"仮締めﾈｼﾞを本締めする"
],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m",
"締付ﾄﾙｸ 1.9N･m",
"締付ﾄﾙｸ 1.9N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"仮締め⇒本締め",
"BOLT BOLT 及び仮締めﾈｼﾞは均等に締め付ける事",
"反時計回りに反転する",
"Y軸ﾍﾞｱ",
"X軸ﾍﾞｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "BOX7㎜",
"ToolOther": "194cN･m",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付③",
"WorkItems": [
"1. X軸ﾍﾞｱを反時計回りに反転し､X軸ﾍﾞｱ受けに乗せる",
"2. X軸ﾍﾞｱをBOLT BOLT WASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"仮締めﾈｼﾞを本締めする"
],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m",
"締付ﾄﾙｸ 1.9N･m",
"締付ﾄﾙｸ 1.9N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"仮締め⇒本締め",
"BOLT BOLT 及び仮締めﾈｼﾞは均等に締め付ける事",
"反時計回りに反転する",
"Y軸ﾍﾞｱ",
"X軸ﾍﾞｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.9N･m",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付④",
"WorkItems": [
"1. X軸ﾌﾞﾗｹｯﾄに配線､配管を通す",
"2. X軸ﾍﾞｱをBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"X軸及びY軸ﾍﾞｱを確認する事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 1.9N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表BOLT :7.組立時調整",
"左側面",
"XMM501",
"CMFP",
"φ8白",
"φ6黄",
"φ6黒",
"CN6K331",
"1A21",
"XEM501P",
"CN1K331",
"φ8白"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.9N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "BOX7㎜",
"ToolOther": "194cN･m",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付④",
"WorkItems": [
"1. X軸ﾌﾞﾗｹｯﾄに配線､配管を通す",
"2. X軸ﾍﾞｱをBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"X軸及びY軸ﾍﾞｱを確認する事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 1.9N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表BOLT :7.組立時調整",
"左側面",
"XMM501",
"CMFP",
"φ8白",
"φ6黄",
"φ6黒",
"CN6K331",
"1A21",
"XEM501P",
"CN1K331",
"φ8白"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY軸ｹｰﾌﾞﾙﾍﾞｱ取付④",
"WorkItems": [
"1. X軸ﾌﾞﾗｹｯﾄに配線､配管を通す",
"2. X軸ﾍﾞｱをBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"X軸及びY軸ﾍﾞｱを確認する事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 1.9N･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表BOLT :7.組立時調整"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"左側面",
"XMM501",
"CMFP",
"φ8白",
"φ6黄",
"φ6黒",
"CN6K331",
"1A21",
"XEM501P",
"CN1K331",
"φ8白",
"WETE-G002-D08"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜ﾛﾝｸﾞﾋﾞｯﾄ",
"ToolOther": "55cN･m",
"WorkName": "ﾍｯﾄﾞ部配線処理1",
"WorkItems": [
"1. ﾓｰﾀｰｺﾈｸﾀ【XMM501】をBOLT WASHER で取付け､配線を固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 55cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ﾗﾍﾞﾙを上に向ける事",
"黒ﾁｭｰﾌﾞ箇所で固定する事",
"ﾌﾛﾝﾄ",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ﾏｳﾝﾄ固定用ﾎﾞﾀﾝﾎﾞﾙﾄの上でﾓｰﾀｰ線と束ねる事",
"･LED照明配線･ｶﾒﾗ配線･ﾘﾆｱｽｹｰﾙ配線"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "55cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理1",
"WorkItems": [
"2. ﾓｰﾀｺﾈｸﾀ【XMM501】を接続し､配線を固定する",
"1. ﾓｰﾀｰｺﾈｸﾀ【XMM501】をBOLT WASHER で取付け､配線を固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 55cN･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:4.ｺﾈｸﾀ接続確認 1-5.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ﾗﾍﾞﾙを上に向ける事",
"黒ﾁｭｰﾌﾞ箇所で固定する事",
"XMM501",
"ﾌﾛﾝﾄ",
"ﾌﾞﾗｹｯﾄに接触し無い事",
"高さｾﾝｻｰ､文字認識仕様時のみ",
"CN13",
"CN5",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ﾏｳﾝﾄ固定用ﾎﾞﾀﾝﾎﾞﾙﾄの上でﾓｰﾀｰ線と束ねる事",
"･LED照明配線･ｶﾒﾗ配線･ﾘﾆｱｽｹｰﾙ配線",
"WETE-G002-D08"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾍｯﾄﾞ部配線処理2",
"WorkItems": [
"1. ①をBOLT BOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ﾄﾘﾑをM/Cの内側に向ける事",
"《右側面》",
"《左側面》",
"ﾎﾞﾙﾄの長さ注意",
"ﾎﾞﾙﾄの長さ注意"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理3",
"WorkItems": [
"1. ｸﾞﾘｰｽﾁｭｰﾌﾞを接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"《右側面》",
"《左側面》",
"右側面へ",
"左側面へ",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"浮き上がら無い事"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ﾍｯﾄﾞ部配線処理4",
"WorkItems": [
"■1. ｱｰｽ線をSCREW で固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:2.ﾈｼﾞ締めﾄﾙｸ確認/ｱｰｽﾗﾍﾞﾙ貼付け確認(1)F"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"右側面",
"EM501(ｵｽ)",
"EM501(ﾒｽ)",
"PEﾗﾍﾞﾙ",
"PEﾗﾍﾞﾙ",
"左側面",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理5",
"WorkItems": [
"1. ﾓｰﾀｰ線を固定する",
"2. ｴｱｰﾎｰｽ(白､黄)を接続し､ﾓｰﾀｰ線に固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸの頭は下へ向ける事",
"《左側面》",
"《左側面》",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ﾌﾞﾗｹｯﾄ上面から上に配線､配管が出無い事",
"断面A-A",
"配管を縦に並べ固定する事"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.6N･m",
"WorkName": "ﾍｯﾄﾞ部配線処理6",
"WorkItems": [
"1. ｶﾒﾗｹｰﾌﾞﾙをSPACER SHIELD BOLT WASHER で固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"《左側面》",
"ｶﾒﾗｹｰﾌﾞﾙを配線(XMM501)､ｴｱｰﾎｰｽ(白黄)より内側を通す事",
"検査表SPACER :4.ｺﾈｸﾀ接続確認 (1)F側 1-4.ｼｰﾙﾄﾞｱｰｽ処理ﾁｪｯｸ/ｱｰｽﾗﾍﾞﾙ貼付け確認",
"FGﾗﾍﾞﾙ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理6",
"WorkItems": [
"1. ｶﾒﾗｹｰﾌﾞﾙをSPACER SHIELD BOLT WASHER で固定する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表SPACER :4.ｺﾈｸﾀ接続確認 (1)F側 1-4.ｼｰﾙﾄﾞｱｰｽ処理ﾁｪｯｸ/ｱｰｽﾗﾍﾞﾙ貼付け確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"《左側面》",
"ｶﾒﾗｹｰﾌﾞﾙを配線(XMM501)､ｴｱｰﾎｰｽ(白黄)より内側を通す事",
"FGﾗﾍﾞﾙ",
"WETE-G002-D08"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理7",
"WorkItems": [
"1. ｴﾝｺｰﾀﾞｰｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:4.ｺﾈｸﾀ接続確認 1-5.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"XEM501",
"CN14",
"CN3/CN4",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WETE-G002-D08"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP】ﾍｯﾄﾞ部配線処理(高さｾﾝｻ、文字認識仕様)",
"WorkItems": [
"1. 配線【CN 5､CN13】をXEM501に固定する"
],
"WorkPoints": [
"仕様を確認し､配線を引き回しする事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"CN5(高さｾﾝｻｰ)",
"CN13(文字認識)",
"XEM501"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "43cN･m",
"WorkName": "ﾍｯﾄﾞ部配線処理8",
"WorkItems": [
"1. 『1A21』をSCREW WASHER で取付ける",
"2. ﾄﾞﾛﾜ配線を固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"CN16",
"CN2",
"CN17"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "43cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ﾍｯﾄﾞ部配線処理9",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ﾍｯﾄﾞ部配線処理10",
"WorkItems": [
"■1. 配線を仮締めし､『FGFX1』『FGFX2』をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:2.ﾈｼﾞ締めﾄﾙｸ確認/ｱｰｽﾗﾍﾞﾙ貼付け確認(1)F側"
],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"CN1",
"CN17",
"CN6",
"CN14",
"CN2",
"FGﾗﾍﾞﾙ",
"仮締め",
"仮締め",
"FGFX2",
"FGFX1",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理11",
"WorkItems": [
"■★1. ①のｼﾘｱﾙNo./型式･DipSWの設定を確認する",
"■★2. ①へｺﾈｸﾀを接続する"
],
"WorkPoints": [
"高さｾﾝｻ仕様時のみ",
"文字認識仕様のみ"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:1.型式･検査書確認 (1)F側"
],
"WorkTypes": [
"■安全作業",
"★静電対策作業",
"■安全作業",
"★静電対策作業"
],
"Words": [
"Dip-SW 8ON",
"型式",
"製造番号",
"CN14",
"CN15ｼｮｰﾄｺﾈｸﾀ",
"CN17",
"CN2",
"CN6",
"CN1",
"CN16",
"CN3",
"CN4",
"CN5",
"CN13",
"CN19ｼｮｰﾄｺﾈｸﾀ",
"CN13はOP:文字認識仕様",
"CN5はOP:高さｾﾝｻ仕様",
"検査表①:3.基板設定確認 (1)F側",
"基板裏面が上側",
"検査表①:4.ｺﾈｸﾀ接続確認 1-1.LED照明制御ﾎﾞｰﾄﾞ",
"検査表②:HS2.ｺﾈｸﾀ接続確認",
"検査表②:CRC1.ｺﾈｸﾀ接続確認",
"WETE-G002-D08"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認､ｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理11",
"WorkItems": [
"■★1. ①のｼﾘｱﾙNo./型式･DipSWの設定を確認する",
"■★2. ①へｺﾈｸﾀを接続する"
],
"WorkPoints": [
"高さｾﾝｻ仕様時のみ",
"文字認識仕様のみ"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:3.基板設定確認 (1)F側"
],
"WorkTypes": [
"■安全作業",
"★静電対策作業",
"■安全作業",
"★静電対策作業"
],
"Words": [
"検査表①:1.型式･検査書確認 (1)F側",
"Dip-SW 8ON",
"型式",
"製造番号",
"CN14",
"CN15ｼｮｰﾄｺﾈｸﾀ",
"CN17",
"CN2",
"CN6",
"CN1",
"CN16",
"CN3",
"CN4",
"CN5",
"CN13",
"CN19ｼｮｰﾄｺﾈｸﾀ",
"CN13はOP:文字認識仕様",
"CN5はOP:高さｾﾝｻ仕様",
"基板裏面が上側",
"検査表①:4.ｺﾈｸﾀ接続確認 1-1.LED照明制御ﾎﾞｰﾄﾞ",
"検査表②:HS2.ｺﾈｸﾀ接続確認",
"検査表②:CRC1.ｺﾈｸﾀ接続確認",
"WETE-G002-D08"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理11",
"WorkItems": [
"■★1. ①のｼﾘｱﾙNo./型式･DipSWの設定を確認する",
"■★2. ①へｺﾈｸﾀを接続する"
],
"WorkPoints": [
"高さｾﾝｻ仕様時のみ",
"文字認識仕様のみ"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表②:HS2.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [
"■安全作業",
"★静電対策作業",
"■安全作業",
"★静電対策作業"
],
"Words": [
"検査表①:1.型式･検査書確認 (1)F側",
"Dip-SW 8ON",
"型式",
"製造番号",
"CN14",
"CN15ｼｮｰﾄｺﾈｸﾀ",
"CN17",
"CN2",
"CN6",
"CN1",
"CN16",
"CN3",
"CN4",
"CN5",
"CN13",
"CN19ｼｮｰﾄｺﾈｸﾀ",
"CN13はOP:文字認識仕様",
"CN5はOP:高さｾﾝｻ仕様",
"検査表①:3.基板設定確認 (1)F側",
"基板裏面が上側",
"検査表①:4.ｺﾈｸﾀ接続確認 1-1.LED照明制御ﾎﾞｰﾄﾞ",
"検査表②:CRC1.ｺﾈｸﾀ接続確認",
"WETE-G002-A03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "7㎜BOX",
"ToolOther": "120cN･m",
"WorkName": "ﾍｯﾄﾞ部配線処理12",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"★静電対策作業"
],
"Words": [
"本締め",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"★静電対策作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理13",
"WorkItems": [
"1. 配管(黒､白)を接続し､固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ﾌﾞﾗｹｯﾄ上面から上に配線､配管が出無い事",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｺﾈｸﾀと干渉無い事",
"ｸﾞﾘｰｽﾆｯﾌﾟﾙ取付ﾌﾞﾛｯｸから外側に配線､配管が出無い事"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "精密ﾏｲﾅｽ",
"ToolOther": "15cN･m",
"WorkName": "ﾍｯﾄﾞ部配線処理14",
"WorkItems": [
"■1. ①へｶﾒﾗｹｰﾌﾞﾙ(CMFR)を固定する",
"■2. 1の完成品をｶﾒﾗｹｰﾌﾞﾙ(CMFP)に接続し､BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:4.ｺﾈｸﾀ接続確認 1-5.ｺﾈｸﾀ接続確認",
"検査表①:4.ｺﾈｸﾀ接続確認 1-5.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"ﾈｼﾞを完全に緩め､片方ずつ枠に通す事",
"■安全作業",
"ｶﾒﾗｹｰﾌﾞﾙ(CMFR)",
"ｶﾒﾗｹｰﾌﾞﾙ(CMFP)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"基板と干渉無い事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "120cN･m",
"WorkName": "ﾍｯﾄﾞ部配線処理14",
"WorkItems": [
"■2. 1の完成品をｶﾒﾗｹｰﾌﾞﾙ(CMFP)に接続し､BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｶﾒﾗｹｰﾌﾞﾙ(CMFR)",
"検査表①:4.ｺﾈｸﾀ接続確認 1-5.ｺﾈｸﾀ接続確認",
"ｶﾒﾗｹｰﾌﾞﾙ(CMFP)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"基板と干渉無い事",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍｯﾄﾞ部配線処理14",
"WorkItems": [
"■1. ①へｶﾒﾗｹｰﾌﾞﾙ(CMFR)を固定する",
"■2. 1の完成品をｶﾒﾗｹｰﾌﾞﾙ(CMFP)に接続し､BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 15cN･m",
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:4.ｺﾈｸﾀ接続確認 1-5.ｺﾈｸﾀ接続確認",
"検査表①:4.ｺﾈｸﾀ接続確認 1-5.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"ｶﾒﾗｹｰﾌﾞﾙ(CMFR)",
"ｶﾒﾗｹｰﾌﾞﾙ(CMFP)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ﾈｼﾞを完全に緩め､片方ずつ枠に通す事",
"基板と干渉無い事",
"WETE-G002-D08"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "55cN･m",
"WorkName": "Xﾋﾞｰﾑ右側_配線処理1",
"WorkItems": [
"1. X軸の左側から右側に可動子配線【YMM506】ｴﾝｺｰﾀﾞ配線【YEM506】を引き回す",
"2. 可動子配線【YMM506】をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 55cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"銘板が見える様に取付ける事",
"YMM506",
"YEM506",
"YMM506",
"YMM506",
"ﾘｱ",
"左側",
"右側",
"Xﾋﾞｰﾑの下面を引き回す事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "55cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Xﾋﾞｰﾑ右側_配線処理2",
"WorkItems": [
"2. SPACER をBOLT WASHER で取付ける",
"1. 可動子配線【YMM506】を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表SPACER :4.ｺﾈｸﾀ接続確認 1-5.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"YMM506",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"被覆部で固定する事",
"ｽﾄｯﾊﾟｰ､固定子ｶﾊﾞｰと干渉無い事",
"ｽﾄｯﾊﾟｰ",
"固定子ｶﾊﾞｰ",
"WETE-G002-D08"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "Xﾋﾞｰﾑ右側_配線処理2",
"WorkItems": [
"2. SPACER をBOLT WASHER で取付ける",
"1. 可動子配線【YMM506】を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"YMM506",
"検査表SPACER :4.ｺﾈｸﾀ接続確認 1-5.ｺﾈｸﾀ接続確認",
"被覆部で固定する事",
"ｽﾄｯﾊﾟｰ",
"固定子ｶﾊﾞｰ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Xﾋﾞｰﾑ右側_配線処理3",
"WorkItems": [
"1. ｴﾝｺｰﾀﾞ配線【YEM506】をﾌﾞﾗｹｯﾄに接続する",
"2. 可動子配線【YMM506】ｴﾝｺｰﾀﾞ配線【YEM506】をXﾋﾞｰﾑ下面に固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"YEM506",
"面取り側を左に向け取付ける事",
"YMM506",
"YEM506",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"上へ向く様に引き回しする事",
"LINEAR-WAY",
"X-ﾋﾞｰﾑ",
"ﾘﾆｱｽｹｰﾙ",
"断面A-A",
"横並びに整線する事",
"配線のたるみ無い事",
"Xﾋﾞｰﾑ下面"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "55cN･m",
"WorkName": "Xﾋﾞｰﾑ左側_配線処理1",
"WorkItems": [
"1. 可動子配線【YMM502】ｴﾝｺｰﾀﾞ配線【YEM502】を引き回す",
"2. 可動子配線【YMM502】をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 55cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"YMM502",
"YEM502",
"ﾌﾛﾝﾄ",
"YMM502",
"YMM502",
"銘板が見える様に取付ける事",
"左側"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "55cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Xﾋﾞｰﾑ左側_配線処理2",
"WorkItems": [
"2. SPACER をBOLT WASHER で取付ける",
"1. 可動子配線【YMM502】を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表SPACER :4.ｺﾈｸﾀ接続確認 1-5.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"YMM502",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｽﾄｯﾊﾟｰ､固定子ｶﾊﾞｰと干渉無い事",
"ｽﾄｯﾊﾟｰ",
"固定子ｶﾊﾞｰ",
"WETE-G002-D08"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "Xﾋﾞｰﾑ左側_配線処理2",
"WorkItems": [
"2. SPACER をBOLT WASHER で取付ける",
"1. 可動子配線【YMM502】を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表SPACER :4.ｺﾈｸﾀ接続確認 1-5.ｺﾈｸﾀ接続確認",
"YMM502",
"ｽﾄｯﾊﾟｰ､固定子ｶﾊﾞｰと干渉無い事",
"ｽﾄｯﾊﾟｰ",
"固定子ｶﾊﾞｰ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Xﾋﾞｰﾑ左側_配線処理3",
"WorkItems": [
"1. ｴﾝｺｰﾀﾞ配線【YEM502】をﾌﾞﾗｹｯﾄに接続する",
"2. 【YMM506】【YEM506】【YMM502】【YEM502】を固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"YEM502",
"面取り側を左に向け取付ける事",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"上へ向く様に引き回しする事"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "X-Y軸連結ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①をSCREW BOLT WASHER BOLT で取付ける",
"2. 1の完成品へSCREW NUT SPACER BOLT WASHER を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 180cN･m",
"締付ﾄﾙｸ 100cN･m",
"締付ﾄﾙｸ 1.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "X-Y軸連結ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①をSCREW BOLT WASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.8N･m",
"WorkName": "X-Y軸連結ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"2. 1の完成品へSCREW NUT SPACER BOLT WASHER を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 180cN･m",
"締付ﾄﾙｸ 100cN･m",
"締付ﾄﾙｸ 1.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "6",
"ToolOther": "100cN･m",
"WorkName": "X-Y軸連結ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"2. 1の完成品へSCREW NUT SPACER BOLT WASHER を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 180cN･m",
"締付ﾄﾙｸ 100cN･m",
"締付ﾄﾙｸ 1.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "X軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理",
"WorkItems": [
"1. X軸ｹｰﾌﾞﾙﾍﾞｱ配線を固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ(300mm)",
"配線の余長吸収箇所",
"ﾍｯﾄﾞをX軸左側ﾒｶｽﾄに当てた時に干渉無い事",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"B2工程前準備にてｾｯﾄ済み"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理1",
"WorkItems": [
"1. Y軸ｹｰﾌﾞﾙﾍﾞｱ配線を固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"外側",
"外側",
"HFPWA",
"φ6",
"φ6",
"CN2K501",
"CNHF",
"HFPWA",
"CN2AK",
"CN2BK",
"CN2K303",
"φ8",
"φ8",
"K501",
"AK502",
"BK502",
"配線を分ける(断面A-A)",
"ｲﾝｼｭﾛｯｸの頭はM/C外側に向ける事",
"7本",
"7本",
"8箇所",
"6箇所",
"ﾌﾞﾗｹｯﾄと干渉無い事"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理2",
"WorkItems": [
"1. ﾍﾞｱ配管を接続し､ﾍﾞｱ配線を固定する",
"2. 架台に配線を引き回し固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"配線を架台の開口部に入れる",
"ﾌﾛﾝﾄ",
"CNP3K501CNP3AK502CNP3BK502",
"CN2K501CN2AK502CN2BK502CN2K303CNHFHFPWA11",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｼﾞｮｲﾝﾄの位置に合わせて配管をｶｯﾄする",
"白配管【701L】",
"白配管【702L】",
"黄配管【301】",
"黒配管【201L】"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理3",
"WorkItems": [
"1. 架台に配線を引き回し固定する",
"2. 架台に配線を引き回し固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"CN2K501CN2AK502CN2BK502CN2K303CNHFHFPWA11",
"ﾘｱへCNHFHFPWA11",
"ﾄﾞﾗｲﾊﾞへCN2K501CN2AK502CN2BK502",
"CPUへCN2K303CN4K303",
"ﾘｱよりCNP4K303",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(200mm)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(300mm)",
"M/C内部へ",
"配管に共締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "120cN･m",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理4",
"WorkItems": [
"1. 架台に配線を引き回し固定する",
"■2. XY軸ﾄﾞﾗｲﾊﾞｰに配線を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:4.ｺﾈｸﾀ接続確認 1-2.ﾓｰﾀﾄﾞﾗｲﾊﾞｰ"
],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"E2K501",
"CNP3K501CNP3AK502CNP3BK502",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "精密ﾏｲﾅｽ",
"ToolOther": "15cN･m",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理5",
"WorkItems": [
"■1. CPU BOXに配線を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:5.CPU BOX-ｺﾈｸﾀ接続確認(1)ｺﾈｸﾀ接続確認"
],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"CN2K303",
"CN4K303",
"検査表①:5.CPC BOX-ｺﾈｸﾀ接続確認(2)ﾈｼﾞ締めﾄﾙｸ",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"CN2K303とCN4K303のｹｰﾌﾞﾙを左右に遠ざけて整線する事",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Y軸ｹｰﾌﾞﾙﾍﾞｱ_配線処理5",
"WorkItems": [
"■1. CPU BOXに配線を接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:5.CPC BOX-ｺﾈｸﾀ接続確認(2)ﾈｼﾞ締めﾄﾙｸ"
],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"CN2K303",
"CN4K303",
"検査表①:5.CPU BOX-ｺﾈｸﾀ接続確認(1)ｺﾈｸﾀ接続確認",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"CN2K303とCN4K303のｹｰﾌﾞﾙを左右に遠ざけて整線する事",
"WETE-G002-D08"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾞﾘｰｽﾁｭｰﾌﾞ取付",
"WorkItems": [
"1. ｸﾞﾘｰｽﾁｭｰﾌﾞを接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"正面図(ﾌﾛﾝﾄ)",
"A部",
"B部",
"左→手前",
"B部",
"右→奥",
"左→奥",
"右→手前",
"A部"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "圧入台",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾘﾆｱｽｹｰﾙ取付(左側)",
"WorkItems": [
"1. 架台へ①をBOLT で取付ける"
],
"WorkPoints": [
"①を取付ける際は､2名作業を徹底する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"下に押し当て隙間無い事",
"左右位置:固定穴ｾﾝﾀｰ",
"ﾌﾛﾝﾄ",
"A矢視",
"A矢視図"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ取付1",
"WorkItems": [
"1. ①②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾘﾆｱｽｹｰﾙと読み取りﾍｯﾄﾞのｼﾘｱﾙNo.を合わせる事",
"通り:0.3㎜/止まり:0.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:8.Y軸ﾘﾆｱｽｹｰﾙの取付･調整",
"正面図(ﾌﾛﾝﾄ)",
"A部",
"A部",
"B部",
"B部",
"配線向き",
"取付け穴のｾﾝﾀｰ合わせ",
"配線向き",
"ｼﾘｱﾙNo.********-02",
"ｼﾘｱﾙNo.$$$$$$$$-01",
"㉙（0.4mm）を挟み隙間を調整し、㉘㉚（0.3mm/0.5mm）で隙間を確認する"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞｷﾞｬｯﾌﾟ調整治具0.3",
"Size": "",
"ToolOther": "FM-2968",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ取付1",
"WorkItems": [
"1. ①②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾘﾆｱｽｹｰﾙと読み取りﾍｯﾄﾞのｼﾘｱﾙNo.を合わせる事",
"通り:0.3㎜/止まり:0.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [
"検査表①:8.Y軸ﾘﾆｱｽｹｰﾙの取付･調整"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"正面図(ﾌﾛﾝﾄ)",
"A部",
"A部",
"B部",
"B部",
"配線向き",
"取付け穴のｾﾝﾀｰ合わせ",
"配線向き",
"ｼﾘｱﾙNo.********-02",
"ｼﾘｱﾙNo.$$$$$$$$-01",
"㉙（0.4mm）を挟み隙間を調整し、㉘㉚（0.3mm/0.5mm）で隙間を確認する"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "通り:0.3㎜止まり:0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞｷﾞｬｯﾌﾟ調整治具0.4",
"Size": "",
"ToolOther": "FM-2707",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ取付1",
"WorkItems": [
"1. ①②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾘﾆｱｽｹｰﾙと読み取りﾍｯﾄﾞのｼﾘｱﾙNo.を合わせる事",
"通り:0.3㎜/止まり:0.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:8.Y軸ﾘﾆｱｽｹｰﾙの取付･調整",
"正面図(ﾌﾛﾝﾄ)",
"A部",
"A部",
"B部",
"B部",
"配線向き",
"取付け穴のｾﾝﾀｰ合わせ",
"配線向き",
"ｼﾘｱﾙNo.********-02",
"ｼﾘｱﾙNo.$$$$$$$$-01",
"㉙（0.4mm）を挟み隙間を調整し、㉘㉚（0.3mm/0.5mm）で隙間を確認する"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "通り:0.3㎜止まり:0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞｷﾞｬｯﾌﾟ調整治具0.5",
"Size": "",
"ToolOther": "FM-2969",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ取付1",
"WorkItems": [
"1. ①②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾘﾆｱｽｹｰﾙと読み取りﾍｯﾄﾞのｼﾘｱﾙNo.を合わせる事",
"通り:0.3㎜/止まり:0.5㎜"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:8.Y軸ﾘﾆｱｽｹｰﾙの取付･調整",
"正面図(ﾌﾛﾝﾄ)",
"A部",
"A部",
"B部",
"B部",
"配線向き",
"取付け穴のｾﾝﾀｰ合わせ",
"配線向き",
"ｼﾘｱﾙNo.********-02",
"ｼﾘｱﾙNo.$$$$$$$$-01",
"㉙（0.4mm）を挟み隙間を調整し、㉘㉚（0.3mm/0.5mm）で隙間を確認する"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "通り:0.3㎜止まり:0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱｽｹｰﾙﾍｯﾄﾞ取付2",
"WorkItems": [
"1. リニアスケールヘッドのコネクタを接続し、㉖㉗で固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WETE-G002-D08",
"InspectionItems": [
"検査表①:4.ｺﾈｸﾀ接続確認 1-5.ｺﾈｸﾀ接続確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"正面図(ﾌﾛﾝﾄ)",
"A部",
"A部",
"B部",
"B部",
"YEM502",
"YEM506",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｼﾘｱﾙNo.********-02",
"ｼﾘｱﾙNo.$$$$$$$$-01",
"配線を上に向ける事",
"配線を上に向ける事",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WETE-G002-D08"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D08",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｵｲﾙ受けｶﾊﾞｰ取付",
"WorkItems": [
"1. COVER をWASHER BOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"正面図(ﾌﾛﾝﾄ)",
"A部",
"A部",
"B部",
"B部"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "部品落下防止ｶﾊﾞｰ取付",
"WorkItems": [
"1. COVER をBOLT WASHER で取付ける",
"2. ﾏﾙﾁｶﾒﾗ配線のﾏｳﾝﾄ(FT11)を差込む"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"差込む",
"ﾏﾙﾁｶﾒﾗ配線1A122A12",
"ﾌﾛﾝﾄ",
"正面図",
"ﾌﾞﾗｹｯﾄと厚肉の間にCOVER を差込む"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "300cN･m",
"WorkName": "ｶﾊﾞｰ取付",
"WorkItems": [
"1. 本体へCOVER をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 300cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ﾌﾛﾝﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "300cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｾｯﾄﾋﾞｽ出代調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6634",
"WorkName": "ｽﾍﾟｰｻｰ取付",
"WorkItems": [
"1. SPACER へSCREW を挿入する",
"2. SPACER へ㉖をセットし、SCREW を挿入する"
],
"WorkPoints": [
"本体取付時に都度作成する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"SCREW が突き当たるまで挿入する事",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6634",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "10.0N･m",
"WorkName": "ｽﾍﾟｰｻｰ取付",
"WorkItems": [
"3. 1の完成品と2の完成品を本体へ取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"左側面",
"2の完成品",
"1の完成品",
"㉖がSPACER へ当たるまで挿入する事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10.0N・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY軸ｸﾞﾘｰｽ封入",
"WorkItems": [
"2. Y軸ストッパー治具（FM-6365）を取り外し、㉗を取付ける",
"◆1. XY軸のグリースニップルから㉖を封入する"
],
"WorkPoints": [
"ﾌﾛﾝﾄ(8箇所)/ﾘｱ(8箇所)行う事",
"配管が満たされるまで給脂する事(目視確認)",
"F/RのX軸を近づけ、㉗が動作する（ブザーが鳴る）事を確認する事",
"はみ出したｸﾞﾘｰｽは拭き取る事"
],
"Tolks": [],
"InspectionNo": "WETE-G002-C02",
"InspectionItems": [
"検査表①:17.XY軸ｸﾞﾘｰｽ封入確認"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"封入箇所③④",
"封入箇所①②",
"封入箇所⑤⑥",
"封入箇所⑦⑧",
"FM-6365",
"Xﾋﾞｰﾑﾌﾞﾗｹｯﾄ下面にSﾋﾟﾝを押し当てる事",
"ﾌﾛﾝﾄX軸",
"WETE-G002-C02"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配管が満たされるまで給脂はみ出し無い事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Y軸二人作業用ｾﾝｻｰｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6693",
"WorkName": "XY軸ｸﾞﾘｰｽ封入",
"WorkItems": [
"2. Y軸ストッパー治具（FM-6365）を取り外し、㉗を取付ける"
],
"WorkPoints": [
"F/RのX軸を近づけ、㉗が動作する（ブザーが鳴る）事を確認する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"封入箇所⑤⑥",
"封入箇所⑦⑧",
"FM-6365",
"Xﾋﾞｰﾑﾌﾞﾗｹｯﾄ下面にSﾋﾟﾝを押し当てる事",
"ﾌﾛﾝﾄX軸",
"◆作業者安全作業",
"WETE-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6693",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C02",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ搭載①",
"WorkItems": [
"◆1. 本体へ①or②を搭載する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ2",
"ﾚｰﾝ1",
"or",
"or",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱ移載用ｼﾞｸﾞ(NPM-WX)",
"Size": "",
"ToolOther": "FM-4831",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ搭載①",
"WorkItems": [
"◆1. 本体へ①or②を搭載する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ2",
"ﾚｰﾝ1",
"or",
"or"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4831",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱ移載用ｼﾞｸﾞ(NPM-WX)",
"Size": "",
"ToolOther": "FM-4831",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ搭載②",
"WorkItems": [
"2. ㉖を取り外す",
"1. ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰをBOLT BOLT BOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCの3か所)",
"締結が完了するまで㉖は外さ無い事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"検査表①:ｺﾝﾍﾞｱﾕﾆｯﾄの取付け確認",
"押し付け",
"押し付け",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(A,B,Cの3箇所)",
"BOLT M6×20WASHER 厚肉座金",
"BOLT M6×25WASHER 厚肉座金",
"BOLT M6×25WASHER 平座金",
"BOLT M6×16WASHER 平座金",
"配線､ﾌｧｲﾊﾞｰ線挟み込み注意",
"配線､ﾌｧｲﾊﾞｰ線挟み込み注意"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4831",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ搭載②",
"WorkItems": [
"1. ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰをBOLT BOLT BOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCの3か所)",
"締結が完了するまで㉖は外さ無い事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾘｱ",
"検査表①:ｺﾝﾍﾞｱﾕﾆｯﾄの取付け確認",
"BOLT M6×20WASHER 厚肉座金",
"BOLT M6×25WASHER 厚肉座金",
"BOLT M6×25WASHER 平座金",
"BOLT M6×16WASHER 平座金"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ搭載②",
"WorkItems": [
"1. ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰをBOLT BOLT BOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCの3か所)",
"締結が完了するまで㉖は外さ無い事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [
"検査表①:ｺﾝﾍﾞｱﾕﾆｯﾄの取付け確認"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾘｱ",
"BOLT M6×20WASHER 厚肉座金",
"BOLT M6×25WASHER 厚肉座金",
"BOLT M6×25WASHER 平座金",
"BOLT M6×16WASHER 平座金",
"WETE-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰ搭載③",
"WorkItems": [
"1. ﾃﾞｭｱﾙｺﾝﾍﾞﾔｰをBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞﾃﾞｭｱﾙ搭載①",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①or②を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事( A C E G I K )",
"二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"ﾊﾞﾙﾌﾞ名称R4212",
"ﾊﾞﾙﾌﾞ名称R4215",
"搭載順序",
"or",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ移載治具",
"Size": "",
"ToolOther": "FM-4489",
"WorkName": "基板ﾎﾙﾀﾞﾃﾞｭｱﾙ搭載①",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①or②を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事( A C E G I K )",
"二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"ﾊﾞﾙﾌﾞ名称R4212",
"ﾊﾞﾙﾌﾞ名称R4215",
"搭載順序",
"or",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4489",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "基板ﾎﾙﾀﾞﾃﾞｭｱﾙ搭載①",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①or②を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事( A C E G I K )",
"二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"ﾊﾞﾙﾌﾞ名称R4212",
"ﾊﾞﾙﾌﾞ名称R4215",
"搭載順序",
"or",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞﾃﾞｭｱﾙ搭載①",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①or②を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事( A C E G I K )",
"二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"ﾊﾞﾙﾌﾞ名称R4212",
"ﾊﾞﾙﾌﾞ名称R4215",
"搭載順序",
"or",
"◆作業者安全作業",
"WETE-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞﾃﾞｭｱﾙ搭載②",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①or②を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事( B D F H J L )",
"二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"ﾊﾞﾙﾌﾞ名称R4712",
"ﾊﾞﾙﾌﾞ名称R4715",
"搭載順序",
"or",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ移載治具",
"Size": "",
"ToolOther": "FM-4489",
"WorkName": "基板ﾎﾙﾀﾞﾃﾞｭｱﾙ搭載②",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①or②を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事( B D F H J L )",
"二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"ﾊﾞﾙﾌﾞ名称R4712",
"ﾊﾞﾙﾌﾞ名称R4715",
"搭載順序",
"or",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4489",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "基板ﾎﾙﾀﾞﾃﾞｭｱﾙ搭載②",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①or②を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事( B D F H J L )",
"二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"ﾊﾞﾙﾌﾞ名称R4712",
"ﾊﾞﾙﾌﾞ名称R4715",
"搭載順序",
"or",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞﾃﾞｭｱﾙ搭載②",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①or②を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事( B D F H J L )",
"二人作業"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"ﾊﾞﾙﾌﾞ名称R4712",
"ﾊﾞﾙﾌﾞ名称R4715",
"搭載順序",
"or",
"◆作業者安全作業",
"WETE-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ搭載①",
"WorkItems": [
"◆1. 本体へ①を搭載する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"◆作業者安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ2",
"ﾚｰﾝ1",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱ移載用ｼﾞｸﾞ(NPM-WX)",
"Size": "",
"ToolOther": "FM-4831",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ搭載①",
"WorkItems": [
"◆1. 本体へ①を搭載する"
],
"WorkPoints": [
"本体との干渉に注意し挿入する事",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"◆作業者安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ2",
"ﾚｰﾝ1",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4831",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｱ移載用ｼﾞｸﾞ(NPM-WX)",
"Size": "",
"ToolOther": "FM-4831",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ搭載②",
"WorkItems": [
"1. ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰをBOLT BOLT で取付ける",
"2. ㉖を取り外す"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCの3か所)",
"締結が完了するまで㉖は外さ無い事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"検査表①:ｺﾝﾍﾞｱﾕﾆｯﾄの取付け確認",
"ﾘｱ",
"押し付け",
"押し付け",
"BOLT M6×20WASHER 厚肉座金",
"BOLT M6×25WASHER 厚肉座金",
"BOLT M6×25WASHER 平座金",
"BOLT M6×16WASHER 平座金",
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(A,B,Cの3箇所)",
"配線､ﾌｧｲﾊﾞｰ線挟み込み注意",
"配線､ﾌｧｲﾊﾞｰ線挟み込み注意"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4831",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ搭載②",
"WorkItems": [],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCの3か所)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾘｱ",
"押し付け",
"BOLT M6×20WASHER 厚肉座金",
"BOLT M6×25WASHER 厚肉座金",
"BOLT M6×25WASHER 平座金",
"BOLT M6×16WASHER 平座金",
"配線､ﾌｧｲﾊﾞｰ線挟み込み注意"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ搭載②",
"WorkItems": [],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCの3か所)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾘｱ",
"押し付け",
"BOLT M6×20WASHER 厚肉座金",
"BOLT M6×25WASHER 厚肉座金",
"BOLT M6×25WASHER 平座金",
"BOLT M6×16WASHER 平座金",
"配線､ﾌｧｲﾊﾞｰ線挟み込み注意",
"WETE-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰ搭載③",
"WorkItems": [
"1. ｼﾝｸﾞﾙｺﾝﾍﾞﾔｰをBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾌﾛﾝﾄ",
"ﾘｱ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞｼﾝｸﾞﾙ搭載①",
"WorkItems": [
"1. ①から延長ﾌﾟﾚｰﾄを取り外す"
],
"WorkPoints": [
"取り外した箇所に戻す為､元の取付け箇所が分かる様にしておく事(ﾈｼﾞも同様)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"延長ﾌﾟﾚｰﾄ",
"延長ﾌﾟﾚｰﾄ"
]
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞｼﾝｸﾞﾙ搭載②",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCDEF)",
"二人作業",
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾊﾞﾙﾌﾞ名称R4712",
"ﾊﾞﾙﾌﾞ名称R4212",
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認",
"ﾌﾛﾝﾄ",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"搭載順序",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ﾎﾙﾀﾞ移載治具",
"Size": "",
"ToolOther": "FM-4852",
"WorkName": "基板ﾎﾙﾀﾞｼﾝｸﾞﾙ搭載②",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCDEF)",
"二人作業",
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾊﾞﾙﾌﾞ名称R4712",
"ﾊﾞﾙﾌﾞ名称R4212",
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認",
"ﾌﾛﾝﾄ",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"搭載順序",
"◆作業者安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4852",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "二人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "基板ﾎﾙﾀﾞｼﾝｸﾞﾙ搭載②",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCDEF)",
"二人作業",
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾊﾞﾙﾌﾞ名称R4712",
"ﾊﾞﾙﾌﾞ名称R4212",
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認",
"ﾌﾛﾝﾄ",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"搭載順序",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞｼﾝｸﾞﾙ搭載②",
"WorkItems": [
"◆1. 可動ﾚｰﾙを広げ､本体へ①を搭載しBOLT WASHER で固定する"
],
"WorkPoints": [
"ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事(ABCDEF)",
"二人作業",
"ｺﾝﾍﾞﾔｰとの干渉に注意し挿入する事"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WETE-G002-A01",
"InspectionItems": [
"検査表①:基板ﾎﾙﾀﾞﾕﾆｯﾄの取付確認"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾊﾞﾙﾌﾞ名称R4712",
"ﾊﾞﾙﾌﾞ名称R4212",
"ﾌﾛﾝﾄ",
"ﾘｱ",
"押し付け",
"押し付け",
"押し付け",
"押し付け",
"搭載順序",
"◆作業者安全作業",
"WETE-G002-A01"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A01",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.5N･m",
"WorkName": "基板ﾎﾙﾀﾞｼﾝｸﾞﾙ搭載③",
"WorkItems": [
"1. 延長ﾌﾟﾚｰﾄを取付ける"
],
"WorkPoints": [
"元の取付け箇所に取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"延長ﾌﾟﾚｰﾄ",
"延長ﾌﾟﾚｰﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "190cN･m",
"WorkName": "ﾍｯﾄﾞｶﾊﾞｰ取付",
"WorkItems": [
"1. ①をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 190cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "190cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.