Datasets:
ayuzawa
/
ManageProcess21

Dataset card Data Studio Files
xet
 Community
1
input
stringclasses
1 value
instruction
stringlengths
223
3.4k
output
stringlengths
206
380
category
stringclasses
1 value
index
stringclasses
1 value
fileName
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "11.5N･m", "WorkName": "逆流れﾌﾚｰﾑ組立、ｵﾌﾟｼｮﾝ(HEPAﾌｨﾙﾀｰﾌﾚｰﾑ)", "WorkItems": [ "2. 1.完成品に⑥をWASHER BOLT で取付ける", "1. ①にNUT SUPPORT を取付ける" ], "WorkPoints": [ "各面の段差が無いように調整し締結する", "ﾌﾚｰﾑ連結の全てのﾎﾞﾙﾄを本締めする", "上面", "この作業は､HEPAﾌｨﾙﾀｰを取付時に実施" ], "Tolks": [ "締付ﾄﾙｸ 11.5N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "11.5N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れ扉開閉上部取付①", "WorkItems": [ "1. ①に⑥を⑦⑳で取付" ], "WorkPoints": [ "拡大図", "正面を内側から見た図" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "600㎜", "ToolOther": "", "WorkName": "逆流れ扉開閉上部取付②", "WorkItems": [ "2. ①に1.完成品と⑥を接続する", "1. TUBE を指定の長さでｶｯﾄする" ], "WorkPoints": [ "内面からの図", "正面", "2軸仕様の場合は下記ｷｯﾄから" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1.完成品", "TUBE \t250mm\t1本\t350mm\t1本", "1.完成品", "350mm", "250mm" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｺﾝﾍﾞｯｸｽ", "Size": "3m", "ToolOther": "", "WorkName": "逆流れ扉開閉上部取付③", "WorkItems": [ "2. ①に1.完成品を接続する", "1. TUBE を指定の長さでｶｯﾄする" ], "WorkPoints": [ "SD-A047677-008のN031 JOINTに接続", "2軸仕様の場合は下記ｷｯﾄから", "正面側", "後面側", "ｶﾊﾞｰ等に干渉しないよう配線･配管を引き回す" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "TUBE \t3000mm\t1本" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｺﾝﾍﾞｯｸｽ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れ非常停止ｽｲｯﾁ取付①", "WorkItems": [ "1. ①に⑥を⑳㉑で取付" ], "WorkPoints": [ "端面合わせ", "正面" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "A矢視図" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れ非常停止ｽｲｯﾁ取付②", "WorkItems": [ "1. ①にCABLE を接続する" ], "WorkPoints": [ "ｶﾊﾞｰ等に干渉しないよう配線を引き回す" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "P1COV5R", "S204R" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "600㎜", "ToolOther": "", "WorkName": "逆流れ扉開閉下部取付", "WorkItems": [ "2. ①に⑥⑦を⑳㉑㉒で取付する", "3. 2.完成品に1.完成品と⑧を接続する", "1. TUBE を指定の長さでｶｯﾄする" ], "WorkPoints": [ "2軸仕様の場合は下記ｷｯﾄから", "内面からの図" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "TUBE \t150mm\t1本\t350mm\t1本", "1.完成品", "1.完成品", "350mm", "150mm" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｺﾝﾍﾞｯｸｽ", "Size": "3㎜", "ToolOther": "", "WorkName": "逆流れ扉開閉下部取付②", "WorkItems": [ "1. TUBE を指定の長さでｶｯﾄする", "2. ①に1.完成品を接続する" ], "WorkPoints": [ "SD-A047677-012のN031 JOINTに接続", "2軸仕様の場合は下記ｷｯﾄから", "正面側", "後面側", "ｶﾊﾞｰ等に干渉しないよう配線･配管を引き回す" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "TUBE \t2000mm\t1本" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｺﾝﾍﾞｯｸｽ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れﾀｰﾐﾅﾙ、D1500取付", "WorkItems": [ "1. ①に②を⑯⑰⑱で取付", "2. 1.完成品にCABLE のD1500を⑲⑳㉑で取付" ], "WorkPoints": [ "正面" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れﾀｰﾐﾅﾙ取付②", "WorkItems": [ "1. ①のﾀｰﾐﾅﾙ配線を引き回す" ], "WorkPoints": [ "ｶﾊﾞｰ等に干渉しないよう配線を引き回す", "正面側", "後面側" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れ扉ｽﾄｯﾊﾟｰ取付", "WorkItems": [ "1. ①に⑥⑦を⑳で取付" ], "WorkPoints": [ "正面" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "1000㎜", "ToolOther": "", "WorkName": "逆流れｼｰﾙ取付", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "逆流れﾋﾝｼﾞ取付", "WorkItems": [ "1. ①に⑥⑦を⑧で取付" ], "WorkPoints": [ "ﾋﾝｼﾞのﾋﾟﾝ無しを取付ける" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "50㎜", "205㎜", "148㎜", "35㎜" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れ後面ｾﾝｻｰ取付", "WorkItems": [ "1. ①に⑥⑦を⑧⑳で取付" ], "WorkPoints": [ "後面", "矢視図" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "600㎜", "ToolOther": "", "WorkName": "逆流れﾒﾝﾃﾅﾝｽﾗｲﾄ取付①", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れﾒﾝﾃﾅﾝｽﾗｲﾄ取付②", "WorkItems": [ "1. ①に⑥を引き回す" ], "WorkPoints": [ "ｶﾊﾞｰ取付等に干渉しないよう配線を引き回す" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "E0131P", "P1TB7R" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "逆流れ電空ﾚｷﾞｭﾚｰﾀ取付①", "WorkItems": [ "1. ①に⑥を⑳㉑で取付" ], "WorkPoints": [ "A矢視図" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｺﾝﾍﾞｯｸｽ", "Size": "5.5m", "ToolOther": "", "WorkName": "逆流れ電空ﾚｷﾞｭﾚｰﾀ取付②", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｺﾝﾍﾞｯｸｽ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "1000㎜", "ToolOther": "", "WorkName": "逆流れ上下流仮置ｲｵﾅｲｻﾞｰ取付(ｵﾌﾟｼｮﾝ)①", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "9-1", "8-1", "8-3", "9-1", "8-1", "8-3" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｺﾝﾍﾞｯｸｽ", "Size": "3.5m", "ToolOther": "", "WorkName": "逆流れ上下流仮置ｲｵﾅｲｻﾞｰ取付(ｵﾌﾟｼｮﾝ)②", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｺﾝﾍﾞｯｸｽ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "逆流れHEPAﾕﾆｯﾄ配線引き回し", "WorkItems": [ "1. ①に⑥・⑦・⑨を引き回し、⑧を㉖で仮固定" ], "WorkPoints": [ "ｶﾊﾞｰ取付等に干渉しないよう配線を引き回す", "配線はﾌﾚｰﾑから先端を20cm出す事", "この作業は､HEPAﾌｨﾙﾀｰを取付時に実施" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "BKbG10347-E1aG10347", "ADPW-01/ADPW-12", "1G10340-8R", "5X012", "BKG10347/RDG10347", "OGG10347/GYG10347", "E1bG10347" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "1000㎜", "ToolOther": "", "WorkName": "逆流れ天井ｶﾊﾞｰ取付準備", "WorkItems": [ "1. ①のｱﾙﾐﾌﾚｰﾑに⑥⑦⑧を挿入" ], "WorkPoints": [ "HEPAﾌｨﾙﾀｰ取付仕様時" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れHEPAﾌｨﾙﾀｰ取付", "WorkItems": [ "1. ①に⑥をBOLT WASHER WASHER で組付け" ], "WorkPoints": [ "この作業は､HEPAﾌｨﾙﾀｰを取付時に実施" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れ天井ｶﾊﾞｰ取付", "WorkItems": [ "1. ①にCOVER ⑦⑧をSCREW WASHER で取付" ], "WorkPoints": [ "上からの図", "ﾌﾚｰﾑからのHEPAﾌｨﾙﾀｰ用ｹｰﾌﾞﾙをｸﾞﾛﾒｯﾄからｶﾊﾞｰ上面へ出しておく事", "HEPAﾌｨﾙﾀｰ取付仕様時" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾌｪﾗｲﾄｺｱ準備", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-184", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [ "WWYJ-5300-184" ] }
{ "QualityItem": "型式確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式が一致する事", "Method": "目視", "RecordMethod": "WWYJ-5300-184", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾌｪﾗｲﾄｺｱ準備", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法の位置に貼付けている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "HEPAﾌｧﾝ配線接続", "WorkItems": [ "■1. ①のHEPAﾌｧﾝに配線を接続" ], "WorkPoints": [ "この作業は､HEPAﾌｨﾙﾀｰを取付時に実施" ], "Tolks": [ "ｹｰﾌﾞﾙ端子締付ﾄﾙｸ 0.6N･m", "ｱｰｽ締付ﾄﾙｸ 1.4N･m" ], "InspectionNo": "WWYJ-5300-123", "InspectionItems": [ "検査表①:接続確認 (5) HEPAﾌｧﾝ" ], "WorkTypes": [ "■安全作業", "■安全作業" ], "Words": [ "上から見た図", "正面側", "後面側", "GYG10347", "上:E1aG10347下:E1bG10347", "OGG10347", "RDG10347", "上:BKG10347下:BKbG10347", "端子ﾈｼﾞ締めﾄﾙｸ M3-0.6N･m", "ｱｰｽﾈｼﾞ締めﾄﾙｸ M4-1.4N･m", "WWYJ-5300-123" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "WWYJ-5300-123", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "0.6N･m", "WorkName": "HEPAﾌｧﾝ配線接続", "WorkItems": [ "■1. ①のHEPAﾌｧﾝに配線を接続" ], "WorkPoints": [ "この作業は､HEPAﾌｨﾙﾀｰを取付時に実施" ], "Tolks": [ "ｹｰﾌﾞﾙ端子締付ﾄﾙｸ 0.6N･m", "ｱｰｽ締付ﾄﾙｸ 1.4N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業", "■安全作業" ], "Words": [ "上から見た図", "正面側", "後面側", "検査表①:接続確認 (5) HEPAﾌｧﾝ", "GYG10347", "上:E1aG10347下:E1bG10347", "OGG10347", "RDG10347", "上:BKG10347下:BKbG10347", "端子ﾈｼﾞ締めﾄﾙｸ M3-0.6N･m", "ｱｰｽﾈｼﾞ締めﾄﾙｸ M4-1.4N･m", "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "0.6N･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "1.4N･m", "WorkName": "HEPAﾌｧﾝ配線接続", "WorkItems": [ "■1. ①のHEPAﾌｧﾝに配線を接続" ], "WorkPoints": [ "この作業は､HEPAﾌｨﾙﾀｰを取付時に実施" ], "Tolks": [ "ｹｰﾌﾞﾙ端子締付ﾄﾙｸ 0.6N･m", "ｱｰｽ締付ﾄﾙｸ 1.4N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業", "■安全作業" ], "Words": [ "上から見た図", "正面側", "後面側", "検査表①:接続確認 (5) HEPAﾌｧﾝ", "GYG10347", "上:E1aG10347下:E1bG10347", "OGG10347", "RDG10347", "上:BKG10347下:BKbG10347", "端子ﾈｼﾞ締めﾄﾙｸ M3-0.6N･m", "ｱｰｽﾈｼﾞ締めﾄﾙｸ M4-1.4N･m", "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "1.4N･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "HEPAﾌｧﾝ配線ﾌｪﾗｲﾄｺｱ取付", "WorkItems": [ "■1. ①のHEPAﾌｧﾝ配線に②ﾌｪﾗｲﾄｺｱを1ﾀｰﾝで取付" ], "WorkPoints": [ "※ｲﾝｼｭﾛｯｸによってHEPAﾕﾆｯﾄ本体に固定されていること｡", "※ｲﾝｼｭﾛｯｸによってｱﾙﾐﾌﾚｰﾑに固定されていること｡", "この作業は､HEPAﾌｨﾙﾀｰを取付時に実施" ], "Tolks": [], "InspectionNo": "WWYJ-5300-184", "InspectionItems": [ "検査表①:ﾌｪﾗｲﾄｺｱ取付け HEPA" ], "WorkTypes": [ "■安全作業", "■安全作業" ], "Words": [ "R230R231", "R234R235R236R237", "正面側", "背面側", "HEPAﾕﾆｯﾄの電源､信号線に1ﾀｰﾝ(R230~R231)", "HEPAﾕﾆｯﾄの電源､ｱｰｽ､信号線に1ﾀｰﾝ(R234~R237)", "WWYJ-5300-184" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "WWYJ-5300-184", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "a,b,c部配管接続", "WorkItems": [ "1. 後部ﾕﾆｯﾄ配管を接続する" ], "WorkPoints": [ "供給部の選択により接続がある場合はｼﾞｮｲﾝﾄにあるﾌﾟﾗｸﾞを取り外し接続します(廃棄)" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "b部", "a部", "φ6白 V001", "仮圧着", "移載", "c部", "b部", "a部", "ACF", "P001", "P003", "c部", "ﾄﾚｲｽﾄｯｶｰ(IC供給有り)", "P022", "φ6黒 P022", "P004", "φ6黒 P004", "V002", "V001", "φ6白 V002", "φ6橙 E021", "E021", "E002", "E001", "φ6橙 E001", "φ6橙 E002", "φ8黒 P002", "φ8黒 P001", "P002", "φ6白 V021", "φ6黒 P021", "P021", "V021", "ﾄﾚｲｽﾃｰｼﾞ(IC供給有り)", "φ6白 V011", "φ6白 V012", "V011", "V012", "φ6黒 P011", "φ6黒 P013", "P015", "P016", "P014", "E012", "E011", "φ6橙 E011", "φ6橙 E012", "P013", "P012", "P011", "φ6黒 P014", "φ6黒 P015", "φ4黒 P016", "φ6白 V022", "V022", "ﾌﾚｰﾑ前側", "ﾌﾚｰﾑ後側", "φ8黒 P003", "φ6黒 P012", "ﾌﾚｰﾑ後側", "ﾌﾚｰﾑ後側" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "f部配管接続", "WorkItems": [ "1. 上流仮置き配管を接続する" ], "WorkPoints": [ "ｵﾌﾟｼｮﾝ追加により接続がある場合はｼﾞｮｲﾝﾄにあるﾌﾟﾗｸﾞを取り外し接続します(廃棄)" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "f部", "φ6白 V061", "φ6黒 P061", "P061", "φ6橙 E063(OP)", "V061", "P066", "φ6黒 P062", "φ6黒 P064", "E061", "φ6黒 P066", "上流仮置ﾕﾆｯﾄ", "φ6黒 P063", "φ4黒 P065", "ｲｵﾅｲｻﾞｰ", "P062", "P063", "P065", "上流仮置ﾕﾆｯﾄ", "ｲｵﾅｲｻﾞｰ", "IC供給ｶﾊﾞｰﾛｯｸ(OP)", "本体ｶﾊﾞｰﾛｯｸ", "φ6黒 P066(OP)", "φ6橙 E061", "φ6橙 E062", "E063", "E062", "P064", "P066", "ﾌﾚｰﾑ前側", "ﾌﾚｰﾑ前側", "ﾌﾚｰﾑ後側" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "e,d部配管接続", "WorkItems": [ "1. 前部ﾕﾆｯﾄ配管を接続する" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾌﾚｰﾑ前側", "e部", "ﾃｰﾌﾞﾙ(A1)", "ﾃｰﾌﾞﾙ(A2)", "d部", "e部", "d部", "φ4黒 P045", "φ6白 V051", "φ6黒 P051", "φ4黒 P052", "P046", "E051", "P052", "搬送ｱｰﾑ1", "φ6白 V041", "V051", "φ6橙 E051", "P051", "φ4黒 P041", "φ4黒 P042", "V043", "φ6白 V043", "P045", "φ4黒 P046", "V041", "P042", "P041", "ﾌﾚｰﾑ前側", "ﾌﾚｰﾑ前側" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "i,h部配管接続", "WorkItems": [ "1. 前部ﾕﾆｯﾄ配管を接続する" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾌﾚｰﾑ前側", "i部", "ﾃｰﾌﾞﾙ(M1)", "h部", "i部", "h部", "φ4黒 P081", "E091", "搬送ｱｰﾑ2", "φ6白 V091", "φ6橙 E091", "P092", "φ4黒 P091", "φ6黒 P092", "φ6白 V082", "φ4黒 P082", "P091", "ﾃｰﾌﾞﾙ(M2)", "V081", "V082", "P082", "P081", "φ6白 V081", "φ4黒 P085", "V091", "φ4黒 P086", "φ4橙 E081", "φ4橙 E082", "E082", "E081", "P086", "P085", "ﾌﾚｰﾑ前側", "ﾌﾚｰﾑ前側" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "水準器", "Size": "0.02㎜/目盛", "ToolOther": "", "WorkName": "架台ﾚﾍﾞﾙ出し", "WorkItems": [ "1. FRAME のﾚﾍﾞﾙを出す" ], "WorkPoints": [ "0.06mm以下", "※ｱｼﾞｬｽﾄﾎﾞﾙﾄ3,6,10の3本を主としてﾚﾍﾞﾙ出しを行う" ], "Tolks": [], "InspectionNo": "WWYJ-5300-003", "InspectionItems": [ "検査表FRAME :本体部ﾍﾞｰｽのﾚﾍﾞﾙ確認" ], "WorkTypes": [], "Words": [ "FRAME ", "WWYJ-5300-003" ] }
{ "QualityItem": "ﾚﾍﾞﾙ確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.06㎜以下", "Method": "校正対象外", "RecordMethod": "WWYJ-5300-003", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "Dﾋﾟﾝ圧入治具", "Size": "", "ToolOther": "FM-2386", "WorkName": "PIN圧入", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "PIN出代", "ToolManageNo": "FM-2386", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "Dﾋﾟﾝ圧入治具", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "", "ToolOther": "", "WorkName": "PIN圧入", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "PIN出代", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "出代:5.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "", "ToolOther": "", "WorkName": "PIN圧入", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "PIN出代", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "出代:10.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "1/100", "ToolOther": "", "WorkName": "ACFｽﾀﾝﾄﾞ取付け", "WorkItems": [ "1. ①にSTAND を取付ける", "2. ｽﾀﾝﾄﾞ上面を測定し調整する" ], "WorkPoints": [ "ﾊﾞﾗﾂｷ:±0.01㎜以内" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "ﾊﾞﾗﾂｷ:±0.01㎜以内", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "測定台", "Size": "", "ToolOther": "FM-2249", "WorkName": "ACFｽﾀﾝﾄﾞ取付け", "WorkItems": [ "1. ①にSTAND を取付ける", "2. ｽﾀﾝﾄﾞ上面を測定し調整する" ], "WorkPoints": [ "ﾊﾞﾗﾂｷ:±0.01㎜以内" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "FM-2249", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ﾊﾞﾗﾂｷ:±0.01㎜以内", "Method": "測定台", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "本認識ｶﾒﾗ取付け", "WorkItems": [ "1. 本認識ﾕﾆｯﾄを付属ﾎﾞﾙﾄで取付ける" ], "WorkPoints": [ "ﾕﾆｯﾄのPIN穴に挿入する", "ﾕﾆｯﾄの平行調整を行う為仮止め" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾎﾞﾙﾄ M8×45 圧肉座金 M8" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "仮圧着ﾊﾞｯｸｱｯﾌﾟﾕﾆｯﾄ取付け", "WorkItems": [ "1. 仮圧着ﾊﾞｯｸｱｯﾌﾟﾕﾆｯﾄを付属ﾎﾞﾙﾄで取付ける" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾎﾞﾙﾄ M10×45" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ACFｽﾃｰｼﾞ、Mｽﾃｰｼﾞ取付け", "WorkItems": [ "1. ACFｽﾃｰｼﾞ､Mｽﾃｰｼﾞを付属ﾎﾞﾙﾄで取付ける" ], "WorkPoints": [ "PIN当てで取付ける", "PIN当てで取付ける", "ﾕﾆｯﾄの平行調整を行う為仮止め", "ｸﾘｰﾝﾍﾞｱを汚さないよう取り扱いに注意すること" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾎﾞﾙﾄ M8×30 12本", "ACF", "Mｽﾃｰｼﾞ", "Aｽﾃｰｼﾞ", "ﾎﾞﾙﾄ M8×30 10本" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ACFﾕﾆｯﾄ取付け", "WorkItems": [ "1. ACFﾕﾆｯﾄを付属ﾎﾞﾙﾄで取付ける" ], "WorkPoints": [ "ﾕﾆｯﾄの平行調整を行う為仮止め" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾎﾞﾙﾄ M12×40 6本", "ACFﾕﾆｯﾄ" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "仮圧着ﾕﾆｯﾄ取付け", "WorkItems": [ "1. 仮圧着ﾕﾆｯﾄを付属ﾎﾞﾙﾄで取付ける" ], "WorkPoints": [ "PIN当てで取付ける", "PIN当てで取付ける", "ｸﾘｰﾝﾍﾞｱを汚さないよう取り扱いに注意すること" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾎﾞﾙﾄ M10×50 4ヶ所", "仮圧着ﾕﾆｯﾄ" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "移載ﾕﾆｯﾄ取付け", "WorkItems": [ "1. 移載ﾕﾆｯﾄを付属ﾎﾞﾙﾄで取付ける" ], "WorkPoints": [ "PIN当てで取付ける", "PIN当てで取付ける", "ｸﾘｰﾝﾍﾞｱを汚さないよう取り扱いに注意すること", "PIN当てで取付ける", "PIN当てで取付ける" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾎﾞﾙﾄ M10×35 4ヶ所", "移載ﾕﾆｯﾄ" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "供給ｶﾒﾗﾕﾆｯﾄ取付け", "WorkItems": [ "1. ①に供給ｶﾒﾗﾕﾆｯﾄを付属ﾎﾞﾙﾄで取付ける" ], "WorkPoints": [ "部品認識ｶﾒﾗ部", "仕様により取付けｶﾒﾗが選択されます" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾎﾞﾙﾄ M6×20 4ヶ所" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ICﾄﾚｲｽﾃｰｼﾞ取付け_IC供給有り", "WorkItems": [ "1. ICﾄﾚｲｽﾃｰｼﾞを付属ﾎﾞﾙﾄで取付ける" ], "WorkPoints": [ "PIN当てで取付ける", "PIN当てで取付ける", "ｸﾘｰﾝﾍﾞｱを汚さないよう取り扱いに注意すること", "IC供給有りの場合実施する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾎﾞﾙﾄ M8×16 14ヶ所", "ICﾄﾚｲｽﾃｰｼﾞ" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ICﾄﾚｲｽﾄｯｶｰ取付け_IC供給有り", "WorkItems": [ "2. ICﾄﾚｲｽﾄｯｶｰを付属ﾎﾞﾙﾄで取付ける", "1. 付属のｽﾀﾝﾄﾞを取付ける" ], "WorkPoints": [ "IC供給有りの場合実施する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾎﾞﾀﾝﾎﾞﾙﾄ M8×16 4ヶ所", "ICﾄﾚｲｽﾄｯｶｰ", "ICﾄﾚｲｽﾄｯｶｰ", "ｽﾀﾝﾄﾞ" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "TCP専用照明取付け_IC供給無し", "WorkItems": [ "1. 付属の支柱を取付ける", "2. 照明部を付属ﾎﾞﾙﾄで取付ける" ], "WorkPoints": [ "IC供給無しの場合実施する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "TCP専用照明", "支柱", "六角穴付きﾎﾞﾙﾄ M6×12 2個みがき丸 6 2個", "照明部" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "上流仮置きﾕﾆｯﾄ取付け", "WorkItems": [ "1. 上流仮置きﾕﾆｯﾄを付属ﾎﾞﾙﾄで取付ける" ], "WorkPoints": [ "ﾕﾆｯﾄのPIN穴に挿入する", "M8×25", "ｸﾘｰﾝﾍﾞｱを汚さないよう取り扱いに注意すること" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾎﾞﾙﾄ M8×25", "上流仮置き" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "穴ｶﾊﾞｰ用ﾎﾟｽﾄ取付とｶﾊﾞｰ取付", "WorkItems": [ "2. 1.の完成品を①に取付け", "1. SPACER へSCREW を挿入" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "PIN出代", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "出代:6.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "2/1000", "ToolOther": "", "WorkName": "ｽﾃｰｼﾞ平行度測定", "WorkItems": [ "1. ｽﾃｰｼﾞ平行度を調整する" ], "WorkPoints": [ "平行度:±10μm以下", "各工程±10μm以下になるようｽﾃｰｼﾞ取付けを調整する" ], "Tolks": [], "InspectionNo": "WWYJ-5500-005", "InspectionItems": [ "検査表①:ｽﾃｰｼﾞ平行度測定" ], "WorkTypes": [], "Words": [ "ｽﾄﾚｰﾄｴｯｼﾞ", "ACF_R", "ACF_L", "M_R", "M_L", "仮圧着", "WWYJ-5500-005" ] }
{ "QualityItem": "平行度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "±10μm以下", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5500-005", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "搬送ｽﾀﾝﾄﾞ取付け", "WorkItems": [ "1. 搬送ｽﾀﾝﾄﾞを付属ﾎﾞﾙﾄで取付ける" ], "WorkPoints": [ "PIN当てで取付ける", "PIN当てで取付ける", "PIN当てで取付ける", "PIN当てで取付ける", "PIN当てで取付ける", "ｸﾘｰﾝﾍﾞｱを汚さないよう取り扱いに注意すること" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾎﾞﾙﾄ M6×30厚肉座金 M6" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "2/1000", "ToolOther": "", "WorkName": "搬送ｽﾀﾝﾄﾞ平行調整", "WorkItems": [ "1. ｽﾀﾝﾄﾞ平行度を調整する" ], "WorkPoints": [ "平行度:30μm以下", "AM側(ｼｮｰﾄ)､MP側(ﾛﾝｸﾞ)が各30μm以下になるようｽﾀﾝﾄﾞ取付けを調整する", "ｽﾀﾝﾄﾞのD-PINから10mmの所を測定すること" ], "Tolks": [], "InspectionNo": "WWYJ-5500-005", "InspectionItems": [ "検査表①:搬送部ｽﾀﾝﾄﾞ平行度測定" ], "WorkTypes": [], "Words": [ "ｽﾄﾚｰﾄｴｯｼﾞ", "M側:ｽﾀﾝﾄﾞ2個", "A側:ｽﾀﾝﾄﾞ2個", "WWYJ-5500-005" ] }
{ "QualityItem": "平行度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "平行度:30μm以下", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5500-005", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "搬送平行だし治具", "Size": "", "ToolOther": "FM-3267", "WorkName": "搬送ｽﾀﾝﾄﾞ平行調整", "WorkItems": [ "1. ｽﾀﾝﾄﾞ平行度を調整する" ], "WorkPoints": [ "平行度:30μm以下", "AM側(ｼｮｰﾄ)､MP側(ﾛﾝｸﾞ)が各30μm以下になるようｽﾀﾝﾄﾞ取付けを調整する", "ｽﾀﾝﾄﾞのD-PINから10mmの所を測定すること" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｽﾄﾚｰﾄｴｯｼﾞ", "検査表①:搬送部ｽﾀﾝﾄﾞ平行度測定", "M側:ｽﾀﾝﾄﾞ2個", "A側:ｽﾀﾝﾄﾞ2個" ] }
{ "QualityItem": "平行度確認", "ToolManageNo": "FM-3267", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "平行度:30μm以下", "Method": "搬送平行だし治具", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽﾃｰｼﾞ治具", "Size": "", "ToolOther": "FM-3403", "WorkName": "ｽﾃｰｼﾞ平面調整", "WorkItems": [ "1. ｽﾃｰｼﾞ平面度を調整する" ], "WorkPoints": [ "①②20μm以下", "FM-3403", "①~④30μm以下" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:[AR]ACF貼付部θｽﾃｰｼﾞ上面平面度", "検査表①:[AL]ACF貼付部θｽﾃｰｼﾞ上面平面度", "検査表①:[MR]仮圧着部ｽﾃｰｼﾞ上面平面度", "検査表①:[ML]仮圧着部ｽﾃｰｼﾞ上面平面度" ] }
{ "QualityItem": "平行度確認", "ToolManageNo": "FM-3403", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "ｽﾃｰｼﾞ治具", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "2/1000", "ToolOther": "", "WorkName": "ｽﾃｰｼﾞ平面調整", "WorkItems": [ "1. ｽﾃｰｼﾞ平面度を調整する" ], "WorkPoints": [ "①②20μm以下", "FM-3403", "①~④30μm以下" ], "Tolks": [], "InspectionNo": "WWYJ-5500-005", "InspectionItems": [ "検査表①:[AR]ACF貼付部θｽﾃｰｼﾞ上面平面度" ], "WorkTypes": [], "Words": [ "検査表①:[AL]ACF貼付部θｽﾃｰｼﾞ上面平面度", "検査表①:[MR]仮圧着部ｽﾃｰｼﾞ上面平面度", "検査表①:[ML]仮圧着部ｽﾃｰｼﾞ上面平面度", "WWYJ-5500-005" ] }
{ "QualityItem": "平行度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "①②20μm以下", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5500-005", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "2/1000", "ToolOther": "", "WorkName": "ｽﾃｰｼﾞ平面調整", "WorkItems": [ "1. ｽﾃｰｼﾞ平面度を調整する" ], "WorkPoints": [ "①②20μm以下", "FM-3403", "①~④30μm以下" ], "Tolks": [], "InspectionNo": "WWYJ-5500-005", "InspectionItems": [ "検査表①:[AL]ACF貼付部θｽﾃｰｼﾞ上面平面度" ], "WorkTypes": [], "Words": [ "検査表①:[AR]ACF貼付部θｽﾃｰｼﾞ上面平面度", "検査表①:[MR]仮圧着部ｽﾃｰｼﾞ上面平面度", "検査表①:[ML]仮圧着部ｽﾃｰｼﾞ上面平面度", "WWYJ-5500-005" ] }
{ "QualityItem": "平行度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "①~④30μm以下", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5500-005", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "1/100", "ToolOther": "", "WorkName": "ACFﾕﾆｯﾄﾌﾚｰﾑ調整", "WorkItems": [ "1. ACFﾕﾆｯﾄを平面調整する", "2. ACFﾕﾆｯﾄを平行調整する", "1. ACFﾕﾆｯﾄを平面調整する", "2. ACFﾕﾆｯﾄを平行調整する" ], "WorkPoints": [ "測定箇所:中央基準に､左右を測定 X差:30μm以内", "測定箇所:ｽﾃｰｼﾞ手前を基準値に､左右各々で測定 Y:30μm以内", "測定箇所:中央基準に､左右を測定 X差:30μm以内", "測定箇所:ｽﾃｰｼﾞ手前を基準値に､左右各々で測定 Y:30μm以内" ], "Tolks": [], "InspectionNo": "WWYJ-5500-005", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5500-005" ] }
{ "QualityItem": "平面度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "中央基準に、左右を測定X差:30μm以内", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5500-005", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "1/100", "ToolOther": "", "WorkName": "ACFﾕﾆｯﾄﾌﾚｰﾑ調整", "WorkItems": [ "1. ACFﾕﾆｯﾄを平面調整する", "2. ACFﾕﾆｯﾄを平行調整する", "1. ACFﾕﾆｯﾄを平面調整する", "2. ACFﾕﾆｯﾄを平行調整する" ], "WorkPoints": [ "測定箇所:中央基準に､左右を測定 X差:30μm以内", "測定箇所:ｽﾃｰｼﾞ手前を基準値に､左右各々で測定 Y:30μm以内", "測定箇所:中央基準に､左右を測定 X差:30μm以内", "測定箇所:ｽﾃｰｼﾞ手前を基準値に､左右各々で測定 Y:30μm以内" ], "Tolks": [], "InspectionNo": "WWYJ-5500-005", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5500-005" ] }
{ "QualityItem": "平面度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "ｽﾃｰｼﾞ手前を基準値に、左右各々で測定Y:30μm以内", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5500-005", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "1/100", "ToolOther": "", "WorkName": "ACFﾕﾆｯﾄﾌﾚｰﾑ調整", "WorkItems": [ "1. ACFﾕﾆｯﾄを平面調整する", "2. ACFﾕﾆｯﾄを平行調整する", "1. ACFﾕﾆｯﾄを平面調整する", "2. ACFﾕﾆｯﾄを平行調整する" ], "WorkPoints": [ "測定箇所:中央基準に､左右を測定 X差:30μm以内", "測定箇所:ｽﾃｰｼﾞ手前を基準値に､左右各々で測定 Y:30μm以内", "測定箇所:中央基準に､左右を測定 X差:30μm以内", "測定箇所:ｽﾃｰｼﾞ手前を基準値に､左右各々で測定 Y:30μm以内" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5500-005" ] }
{ "QualityItem": "平行度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "30μm以内", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5500-005", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "2/1000", "ToolOther": "", "WorkName": "ACFﾊﾞｯｸｱｯﾌﾟ上面測定", "WorkItems": [ "1. 定盤上を基準に､ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞ上面の平行度を測定する" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5500-005", "InspectionItems": [ "検査表①:ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞ平面度測定" ], "WorkTypes": [], "Words": [ "ｽﾃｰｼﾞ", "ﾊﾞｯｸｱｯﾌﾟﾍﾞｰｽ", "各ｽﾃｰｼﾞ X方向:20μm以内 Y方向:10μm以内 L･R段差:50μm以内", "WWYJ-5500-005" ] }
{ "QualityItem": "平行度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "X方向:20μm以内", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5500-005", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "2/1000", "ToolOther": "", "WorkName": "ACFﾊﾞｯｸｱｯﾌﾟ上面測定", "WorkItems": [ "1. 定盤上を基準に､ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞ上面の平行度を測定する" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｽﾃｰｼﾞ", "ﾊﾞｯｸｱｯﾌﾟﾍﾞｰｽ", "各ｽﾃｰｼﾞ X方向:20μm以内 Y方向:10μm以内 L･R段差:50μm以内", "検査表①:ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞ平面度測定", "WWYJ-5500-005" ] }
{ "QualityItem": "平行度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "Y方向:10μm以内", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5500-005", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "2/1000", "ToolOther": "", "WorkName": "ACFﾊﾞｯｸｱｯﾌﾟ上面測定", "WorkItems": [ "1. 定盤上を基準に､ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞ上面の平行度を測定する" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｽﾃｰｼﾞ", "ﾊﾞｯｸｱｯﾌﾟﾍﾞｰｽ", "各ｽﾃｰｼﾞ X方向:20μm以内 Y方向:10μm以内 L･R段差:50μm以内", "検査表①:ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞ平面度測定", "WWYJ-5500-005" ] }
{ "QualityItem": "平行度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "L・R段差:50μm以内", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5500-005", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "2/1000", "ToolOther": "", "WorkName": "仮圧着ﾊﾞｯｸｱｯﾌﾟ平面平行確認", "WorkItems": [ "1. 仮圧着ﾊﾞｯｸｱｯﾌﾟﾍﾞｰｽの平面平行を確認する" ], "WorkPoints": [ "平面度:20μm以下", "平行度:0.2mm以内" ], "Tolks": [], "InspectionNo": "WWYJ-5500-005", "InspectionItems": [ "検査表①:ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞ平面度測定" ], "WorkTypes": [], "Words": [ "検査表①:ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞ平行度測定", "WWYJ-5500-005" ] }
{ "QualityItem": "平面度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "平面度:20μm以下", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5500-005", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "2/1000", "ToolOther": "", "WorkName": "仮圧着ﾊﾞｯｸｱｯﾌﾟ平面平行確認", "WorkItems": [ "1. 仮圧着ﾊﾞｯｸｱｯﾌﾟﾍﾞｰｽの平面平行を確認する" ], "WorkPoints": [ "平面度:20μm以下", "平行度:0.2mm以内" ], "Tolks": [], "InspectionNo": "WWYJ-5500-005", "InspectionItems": [ "検査表①:ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞ平行度測定" ], "WorkTypes": [], "Words": [ "検査表①:ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞ平面度測定", "WWYJ-5500-005" ] }
{ "QualityItem": "平行度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "平行度:0.2㎜以内", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5500-005", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "Size": "1/100", "ToolOther": "", "WorkName": "仮圧着ﾊﾞｯｸｱｯﾌﾟ出しろ測定", "WorkItems": [ "1. 仮圧着ﾂｰﾙとﾊﾞｯｸｱｯﾌﾟﾍﾞｰｽの出代を確認する" ], "WorkPoints": [ "①XY軸にｽﾀﾝﾄﾞを固定し､Z軸を動かし測定②測定箇所は､各ﾂｰﾙ･ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞ前面の中央※ﾂｰﾙ前面に対し､ﾊﾞｯｸｱｯﾌﾟ前面が出ている状態", "出代量:-0.10~-0.30mm" ], "Tolks": [], "InspectionNo": "WWYJ-5500-005", "InspectionItems": [ "検査表①:ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞ出しろ測定" ], "WorkTypes": [], "Words": [ "WWYJ-5500-005" ] }
{ "QualityItem": "出代確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "出代量:-0.10~-0.30㎜", "Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ", "RecordMethod": "WWYJ-5500-005", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "搬送ﾕﾆｯﾄ取付け", "WorkItems": [ "1. 搬送ﾕﾆｯﾄを付属ﾎﾞﾙﾄで取付ける" ], "WorkPoints": [ "ﾃｰﾌﾞﾙの配管配線が完了している事", "ｸﾘｰﾝﾍﾞｱを汚さないよう取り扱いに注意すること", "ﾏｸﾞﾈｯﾄ注意" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾎﾞﾙﾄ M6×16 20ヶ所", "搬送ﾕﾆｯﾄ", "A側", "M側", "A側", "M側" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｶﾊﾞｰﾌﾚｰﾑ取付け", "WorkItems": [ "1. ①にﾌﾚｰﾑをWASHER BOLT で取付ける" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "後面ｶﾊﾞｰﾌﾞﾗｹｯﾄ取付け", "WorkItems": [ "1. ①にBRACKET をBOLT WASHER で取付ける" ], "WorkPoints": [ "架台前面に合わせる", "2ヶ所" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "設備後側" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "上流仮置きｶﾊﾞｰﾌﾚｰﾑ取付け", "WorkItems": [ "1. ①に仮置きｶﾊﾞｰ(R)を付属ﾎﾞﾙﾄで取付ける" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾎﾞﾙﾄ M6×16歯付座金 M6" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "HEPA取付け", "WorkItems": [ "1. ①にHEPAを付属ﾎﾞﾙﾄで取付ける" ], "WorkPoints": [ "ｽｲｯﾁを前側で取付ける", "ｽｲｯﾁを後側で取付ける", "ACF､仮圧着はﾏｳﾝﾄの取付け位置が違います", "ｶﾊﾞｰ取付け後､隙間を調整して締め付けをする" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ﾎﾞﾙﾄ M6×12厚肉座金 M6", "ACF", "仮圧着", "510㎜", "523㎜" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "本体天板取付け", "WorkItems": [ "1. ①に天板を付属ﾎﾞﾙﾄで取付ける", "2. HEPAの取付けﾎﾞﾙﾄを締め付ける" ], "WorkPoints": [ "HEPAの取付けと隙間を調整して締め付けをする" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "+字穴付きﾄﾗｽ小ねじ M4×10ﾅｲﾛﾝﾜｯｼｬ M4" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "上流仮置きｲｵﾅｲｻﾞｰ共通部取付け", "WorkItems": [ "1. ①に上流仮置きｲｵﾅｲｻﾞｰを付属ﾎﾞﾙﾄで取付ける" ], "WorkPoints": [ "前側" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "六角穴付きﾎﾞﾙﾄ M4×10みがき丸 M4", "206㎜" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法:206.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "上流仮置きｲｵﾅｲｻﾞｰ取付け部取付け", "WorkItems": [ "1. ①に上流仮置きｲｵﾅｲｻﾞｰを付属ﾎﾞﾙﾄで取付ける" ], "WorkPoints": [ "前側" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "六角穴付きﾎﾞﾙﾄ M4×10みがき丸 M4" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法:300.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "供給部連結ﾌﾞﾛｯｸ取付け_TCP供給有り", "WorkItems": [ "1. BRACKET にSHAFT をBOLT で取付ける", "2. ①に1の完成品と、BRACKET をBOLT ㉒で取付ける" ], "WorkPoints": [ "TCP供給有りの場合実施する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "後部" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｶﾞｽｹｯﾄ貼付け①前面", "WorkItems": [ "1. ①へGASKET GASKET 貼付ける" ], "WorkPoints": [ "貼付け部分のｺﾞﾐ･油脂を取り除く" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1㎜", "合わせる", "490mm", "12.5㎜", "合わせる", "494mm", "12.5㎜", "合わせる", "494mm", "1㎜", "合わせる", "490mm", "12.5㎜", "合わせる", "494mm" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｶﾞｽｹｯﾄ貼付け②前面", "WorkItems": [ "1. ①へGASKET GASKET GASKET GASKET GASKET GASKET GASKET GASKET を貼付ける" ], "WorkPoints": [ "貼付け部分のｺﾞﾐ･油脂を取り除く", "ｶﾊﾞｰ取付け穴間に貼付ける" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "863mm", "871mm", "935mm", "415mm", "418mm", "451mm", "873mm", "419mm" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｶﾞｽｹｯﾄ貼付け③後面", "WorkItems": [ "1. ①へGASKET GASKET 貼付ける" ], "WorkPoints": [ "貼付け部分のｺﾞﾐ･油脂を取り除く" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "合わせる", "409mm", "13㎜", "合わせる", "494mm", "1㎜", "合わせる", "490mm", "13㎜" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "1000㎜", "ToolOther": "", "WorkName": "ｶﾞｽｹｯﾄ貼付け④後面", "WorkItems": [ "1. ①へGASKET GASKET GASKET GASKET GASKET ⑧を貼付ける" ], "WorkPoints": [ "貼付け部分のｺﾞﾐ･油脂を取り除く", "ｶﾊﾞｰ取付け穴間に貼付ける", "縦方向のｶﾞｽｹｯﾄに合わす" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "516mm", "476mm", "412mm", "808mm", "453mm", "419mm" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "IC専用ｶﾊﾞｰﾌﾞﾗｹｯﾄ取付け①_TCP供給無し", "WorkItems": [ "1. ①へ⑥を⑳㉑で取付ける" ], "WorkPoints": [ "TCP供給無しの場合実施する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "IC専用ｶﾊﾞｰﾌﾞﾗｹｯﾄ取付け②_TCP供給無し", "WorkItems": [ "1. ①へ⑥を⑳㉑で取付ける" ], "WorkPoints": [ "ﾌﾞﾗｹｯﾄの面が架台の面と平行で段差が無きよう取付けﾎﾞﾙﾄで調整する", "TCP供給無しの場合実施する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "1000㎜", "ToolOther": "", "WorkName": "IC専用ｶﾞｽｹｯﾄ貼付け_TCP供給無し", "WorkItems": [ "1. ①へ⑥⑦⑧を貼付ける" ], "WorkPoints": [ "ｶﾊﾞｰ取付け穴間に貼付ける", "縦方向のｶﾞｽｹｯﾄに合わす", "貼付け部分のｺﾞﾐ･油脂を取り除く", "TCP供給無しの場合実施する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "381mm", "798mm", "494mm", "8㎜", "7㎜", "494mm", "8㎜", "合わせる", "合わせる" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "作業指示の寸法である事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "水準器", "Size": "0.02㎜/目盛", "ToolOther": "", "WorkName": "逆流れ本体組立①", "WorkItems": [ "1. FRAME にADJUST BOLT ASSY を取付" ], "WorkPoints": [ "正面", "片側で0.06mm以下/1000 mm" ], "Tolks": [], "InspectionNo": "WWYJ-5300-011", "InspectionItems": [ "検査表FRAME :本体部ﾍﾞｰｽのﾚﾍﾞﾙ確認" ], "WorkTypes": [], "Words": [ "※上記範囲に入ること1DIV=0.02使用", "WWYJ-5300-011" ] }
{ "QualityItem": "平行度確認", "ToolManageNo": "-", "ToolCycle": "1回/半年", "ToolRecord": "校正成績書", "StdVal": "0.02㎜以下", "Method": "水準器", "RecordMethod": "WWYJ-5300-011", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "逆流れ本体組立②(上面)", "WorkItems": [ "1. ①にPIN PIN 又はPIN PIN を圧入" ], "WorkPoints": [ "ﾋﾟﾝ圧入詳細青丸枠は共通部 PIN を6本黒丸枠は1軸仕様､2軸仕様共用 PIN orPIN を3本茶丸枠は1軸仕様 PIN を7本黄丸枠は2軸仕様 PIN を6本", "出代 5mm", "仕様(1軸仕様/2軸仕様)に準じて圧入する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "PIN出代", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法:5.0㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.01㎜", "ToolOther": "", "WorkName": "逆流れ本体組立③(本圧着ﾄﾞｯｷﾝｸﾞ)", "WorkItems": [ "1. ①に⑥を載せてBOLT で固定" ], "WorkPoints": [ "PINに当付け（㉗で確認する）", "隙間:0.01㎜以下" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "隙間:0.01㎜以下", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.01㎜", "ToolOther": "", "WorkName": "逆流れ本体組立④(XYﾃｰﾌﾞﾙﾄﾞｯｷﾝｸﾞ)", "WorkItems": [ "1. ①に⑥を載せて⑳で固定" ], "WorkPoints": [ "PINに当付け（㉗で確認する）", "隙間:0.01㎜以下", "⑥ﾃｰﾌﾞﾙﾕﾆｯﾄはﾍﾞｰｽﾌﾟﾚｰﾄのみ描いています" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "隙間:0.01㎜以下", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.01㎜", "ToolOther": "", "WorkName": "逆流れ本体組立⑤(1軸仕様搬送部ﾄﾞｯｷﾝｸﾞ)", "WorkItems": [ "1. ①に⑥搬送部をWASHER BOLT で取付ける" ], "WorkPoints": [ "上面", "隙間:0.01㎜以下", "基準ﾋﾟﾝに⑥を押し当て隙間のないように取付" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1軸仕様の場合" ] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "隙間:0.01㎜以下", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れ本体組立⑥(1軸仕様搬送部ﾄﾞｯｷﾝｸﾞ)", "WorkItems": [ "1. ①にSCREW を取付", "2. 1.完成品に⑥をSPACER WASHER ㉒で取付" ], "WorkPoints": [ "上面" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1軸仕様の場合" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れ本体組立⑦(1軸仕様搬送部ﾄﾞｯｷﾝｸﾞ)", "WorkItems": [ "1. ①に⑥をBOLT で取付", "2. 1.完成品のケーブルベアをBOLT ㉒WASHER で取付" ], "WorkPoints": [ "上面", "矢視" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1軸仕様の場合" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れ本体組立⑧(1軸仕様SP1X軸ﾌｪﾗｲﾄｺｱ取付)", "WorkItems": [ "1. 配線3本配管3本をFT4に㉖で固定", "■2. 付属のフェライトコアを所定の配線（モーター線、エンコーダー線、信号線）に㉖で固定", "3. 1.完成品をブラケット上のFT4に⑥を俵積みして㉗で固定" ], "WorkPoints": [ "配線1本に⑥を2個固定", "⑥を配線に㉖で固定", "矢視" ], "Tolks": [], "InspectionNo": "WWYJ-5300-184", "InspectionItems": [ "検査表①:ﾌｪﾗｲﾄｺｱ取付 ﾊﾟﾈﾙ搬送部(SP1X)" ], "WorkTypes": [ "■安全作業", "■安全作業" ], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "ﾌｪﾗｲﾄｺｱ", "1軸仕様の場合", "WWYJ-5300-184" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "WWYJ-5300-184", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.01㎜", "ToolOther": "", "WorkName": "逆流れ本体組立⑨(2軸仕様搬送部ﾄﾞｯｷﾝｸﾞ)", "WorkItems": [ "1. ①に⑥搬送部を⑳㉑で取付ける" ], "WorkPoints": [ "上面", "隙間:0.01㎜以下", "基準ﾋﾟﾝに⑥を押し当て隙間のないように取付" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [ "2軸仕様の場合" ] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "隙間:0.01㎜以下", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れ本体組立⑩(2軸仕様搬送部ﾄﾞｯｷﾝｸﾞ)", "WorkItems": [ "2. 1完成品に⑧を取付け", "3. 2.完成品に⑥⑦を㉑㉒で取付", "1. ①に⑳を取付" ], "WorkPoints": [ "上面", "略図､茶色丸枠の架台上面に取付", "略図､茶色､黄色丸枠部分に取付" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [ "2軸仕様の場合" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れ本体組立⑪(2軸仕様搬送部ﾄﾞｯｷﾝｸﾞ)", "WorkItems": [ "1. ①に⑥を⑳で取付", "2. 1.完成品のケーブルベアを㉑㉒㉓で取付" ], "WorkPoints": [ "上面", "矢視" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [ "2軸仕様の場合" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れ本体組立⑫(2軸仕様SP1X軸ﾌｪﾗｲﾄｺｱ取付)", "WorkItems": [ "1. ①のSP1X軸配線3本配管3本をFT4に㉗で固定", "■2. ⑥付属のフェライトコアを所定の配線（モーター線、エンコーダー線、信号線）に㉖で固定", "3. 1.完成品をブラケット上のFT4に⑥を俵積みして㉗で固定" ], "WorkPoints": [ "フェライトコアを配線に㉖で固定", "矢視" ], "Tolks": [], "InspectionNo": "WWYJ-5300-184", "InspectionItems": [ "検査表①:ﾌｪﾗｲﾄｺｱ取付 ﾊﾟﾈﾙ搬送部(SP1X)" ], "WorkTypes": [ "■安全作業", "■安全作業" ], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "ﾌｪﾗｲﾄｺｱ", "2軸仕様の場合", "WWYJ-5300-184" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "WWYJ-5300-184", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れ本体組立⑬(2軸仕様SDX軸ﾌｪﾗｲﾄｺｱ取付)", "WorkItems": [ "1. ①のSDX軸配線3本配管3本をFT4に㉗で固定", "3. 1.完成品をブラケット上のFT4に俵積みして㉗で固定", "■2. ⑥付属のフェライトコアを所定の配線（モーター線、エンコーダー線、信号線）に㉖で固定" ], "WorkPoints": [ "矢視", "配線1本にﾌｪﾗｲﾄｺｱを1個固定", "フェライトコアを配線に㉖で固定" ], "Tolks": [], "InspectionNo": "WWYJ-5300-184", "InspectionItems": [ "検査表①:ﾌｪﾗｲﾄｺｱ取付 ﾊﾟﾈﾙ搬送部(SDX)" ], "WorkTypes": [ "■安全作業", "■安全作業" ], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "ﾌｪﾗｲﾄｺｱ", "2軸仕様の場合", "WWYJ-5300-184" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "WWYJ-5300-184", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れ本体組立⑭(上面)", "WorkItems": [ "1. ①に②をBOLT WASHER で取付(5個)", "2. 1､完成品に③をBOLT WASHER で取付(2個)" ], "WorkPoints": [ "N004ｽﾍﾟｰｻｰ無し", "N004ｽﾍﾟｰｻｰ有り", "N004ｽﾍﾟｰｻｰ有" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "逆流れ本体組立⑮", "WorkItems": [ "1. ①に⑥をWASHER BOLT で取付" ], "WorkPoints": [ "各面の段差が無いように調整し締結する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "逆流れ本体組立⑯(前面ｶﾞｽｹｯﾄ取付)", "WorkItems": [ "1. ①にGASKET GASKET GASKET GASKET を貼付" ], "WorkPoints": [ "正面" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法の位置に貼付けている事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null