input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ左側組立1",
"WorkItems": [
"2. SENSOR(600MM) をBRACKET にSENSOR(600MM) SCREW WASHER WASHER で取付ける",
"3. SENSOR(600MM) をBRACKET にSENSOR(600MM) SCREW WASHER WASHER で取付ける",
"■1. 型式を確認し､ﾛｯﾄNo.･ｼﾘｱﾙNo.を記入する"
],
"WorkPoints": [
"ｾﾝｻ:B･C",
"ﾌﾟﾚｰﾄの向きに注意する事",
"ﾌﾟﾚｰﾄの向きに注意する事",
"ｾﾝｻ:A･D",
"受光側ｾﾝｻ:4個作製",
"受光側ｾﾝｻ:4個作製",
"EX-L212D",
"EX-L212D",
"投光側(ｹｰﾌﾞﾙ灰色)",
"受光側(ｹｰﾌﾞﾙ黒色)",
"受光側型式",
"ﾛｯﾄNo.",
"ｼﾘｱﾙNo."
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "WEPJ-G002-C16",
"InspectionItems": [
"検査表SENSOR(600MM) :ﾃｰﾌﾟ浮き検出ｾﾝｻの型式確認とﾛｯﾄNo.記録"
],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"WEPJ-G002-C16"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認･ﾛｯﾄ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C16",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "80cN･m",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ左側組立2",
"WorkItems": [
"1. ①をPLATE にSCREW で取付ける",
"2. 1完成品ｺﾈｸﾀｰに⑥を取付ける",
"■3. ﾛｯﾄNo.･ｼﾘｱﾙNo.を記入する"
],
"WorkPoints": [
"防錆油を塗布すること(全体)",
"F/R それぞれ1台 計2台作成",
"ｾﾝｻｰ部に防錆油が付着した場合は拭取ること",
"ｾﾝｻ:C",
"ｾﾝｻ:D",
"ｾﾝｻ:A",
"ｾﾝｻ:B",
"被覆端面に合わせてﾗﾍﾞﾙを取付ける",
"取付け例",
"F/R それぞれ1台 計2台作成",
"ﾛｯﾄNo.",
"ｼﾘｱﾙNo."
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"F用",
"R用",
"B1231R",
"B1237R",
"B1232R",
"B1240R",
"B1233R",
"B1241R",
"B1234R",
"B1242R",
"ｾﾝｻ:D",
"ｾﾝｻ:C",
"ｾﾝｻ:B",
"ｾﾝｻ:A",
"B1231R",
"検査表①:ﾃｰﾌﾟ浮き検出ｾﾝｻの型式確認とﾛｯﾄNo.記録",
"■安全作業"
]
} | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ左側組立2",
"WorkItems": [
"1. ①をPLATE にSCREW で取付ける",
"2. 1完成品ｺﾈｸﾀｰに⑥を取付ける",
"■3. ﾛｯﾄNo.･ｼﾘｱﾙNo.を記入する"
],
"WorkPoints": [
"防錆油を塗布すること(全体)",
"F/R それぞれ1台 計2台作成",
"ｾﾝｻｰ部に防錆油が付着した場合は拭取ること",
"ｾﾝｻ:C",
"ｾﾝｻ:D",
"ｾﾝｻ:A",
"ｾﾝｻ:B",
"被覆端面に合わせてﾗﾍﾞﾙを取付ける",
"取付け例",
"F/R それぞれ1台 計2台作成",
"ﾛｯﾄNo.",
"ｼﾘｱﾙNo."
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "WEPJ-G002-C16",
"InspectionItems": [
"検査表①:ﾃｰﾌﾟ浮き検出ｾﾝｻの型式確認とﾛｯﾄNo.記録"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"F用",
"R用",
"B1231R",
"B1237R",
"B1232R",
"B1240R",
"B1233R",
"B1241R",
"B1234R",
"B1242R",
"ｾﾝｻ:D",
"ｾﾝｻ:C",
"ｾﾝｻ:B",
"ｾﾝｻ:A",
"B1231R",
"WEPJ-G002-C16"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾛｯﾄ、ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C16",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "50cN･m",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ右側組立1",
"WorkItems": [],
"WorkPoints": [
"ｾﾝｻ:A･B･C",
"ｾﾝｻ:D",
"EX-L212",
"EX-L212",
"投光側型式",
"ﾛｯﾄNo.",
"ｼﾘｱﾙNo.",
"ｾﾝｻ:A･B･C",
"ｾﾝｻ:D",
"EX-L212",
"EX-L212",
"投光側型式",
"ﾛｯﾄNo.",
"ｼﾘｱﾙNo."
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ右側組立1",
"WorkItems": [
"3. SENSOR(600MM) をPLATE にSENSOR(600MM) SCREW WASHER WASHER で取付ける",
"2. SENSOR(600MM) をPLATE にSENSOR(600MM) SCREW WASHER WASHER で取付ける",
"■1. 型式を確認し､ﾛｯﾄNo.･ｼﾘｱﾙNo.を記入する"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄの向きに注意する",
"ｾﾝｻ:A･B･C",
"ﾌﾟﾚｰﾄの向きに注意する",
"ｾﾝｻ:D",
"投光側ｾﾝｻ:6個作製",
"投光側ｾﾝｻ:2個作製",
"EX-L212",
"EX-L212",
"投光側(ｹｰﾌﾞﾙ灰色)",
"受光側(ｹｰﾌﾞﾙ黒色)",
"投光側型式",
"ﾛｯﾄNo.",
"ｼﾘｱﾙNo."
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "WEPJ-G002-C16",
"InspectionItems": [
"検査表SENSOR(600MM) :ﾃｰﾌﾟ浮き検出ｾﾝｻの型式確認とﾛｯﾄNo.記録"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"WEPJ-G002-C16"
]
} | {
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認･ﾛｯﾄ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C16",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ右側組立2",
"WorkItems": [
"2. ①へBRACKET をBOLT WASHER で仮取付けする"
],
"WorkPoints": [
"取付け方向に注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ右側組立3",
"WorkItems": [
"1. ①に⑥を取付ける"
],
"WorkPoints": [
"被覆端面に合わせてﾗﾍﾞﾙを取付ける",
"取付け例",
"2台作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"F用",
"R用",
"B1234TR",
"B1242TR",
"B1233TR",
"B1241TR",
"B1232TR",
"B1240TR",
"B1231TR",
"B1237TR",
"ｾﾝｻ:A",
"ｾﾝｻ:B",
"ｾﾝｻ:C",
"ｾﾝｻ:D",
"B1231TR",
"WEPJ-G002-C16"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾛｯﾄ、ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C16",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌｨｰﾀﾞｰｾﾝｻ位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6153",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ調整1",
"WorkItems": [
"1. ①②を治具に取付ける"
],
"WorkPoints": [
"ｺﾈｸﾀｰﾗﾍﾞﾙを確認し各ｽﾃｰｼﾞの組合せを間違わない様取付けの事",
"この作業については､ｾﾝｻｰA･B･C･Dの順で順次調整を行い締結を行う事※ｾﾝｻｰ間のｽｷﾏが小さくﾄﾙｸﾄﾞﾗｲﾊﾞｰか入らない為",
"･実際のﾏｼﾝ取付穴｡･治具に使用しての取付穴 は異なるにで注意｡",
"ｺﾈｸﾀを接続",
"【厳守】 接続時の治具の電源は(OFF)",
"ｾﾝｻ:A",
"ｾﾝｻ:B",
"ｾﾝｻ:C",
"ｾﾝｻ:D",
"調整側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｾﾝｻ:A",
"ｾﾝｻ:B",
"ｾﾝｻ:C",
"ｾﾝｻ:D"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6153",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2375",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ調整1",
"WorkItems": [
"1. ①②を治具に取付ける"
],
"WorkPoints": [
"ｺﾈｸﾀｰﾗﾍﾞﾙを確認し各ｽﾃｰｼﾞの組合せを間違わない様取付けの事",
"この作業については､ｾﾝｻｰA･B･C･Dの順で順次調整を行い締結を行う事※ｾﾝｻｰ間のｽｷﾏが小さくﾄﾙｸﾄﾞﾗｲﾊﾞｰか入らない為",
"･実際のﾏｼﾝ取付穴｡･治具に使用しての取付穴 は異なるにで注意｡",
"ｺﾈｸﾀを接続",
"【厳守】 接続時の治具の電源は(OFF)",
"ｾﾝｻ:A",
"ｾﾝｻ:B",
"ｾﾝｻ:C",
"ｾﾝｻ:D",
"調整側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｾﾝｻ:A",
"ｾﾝｻ:B",
"ｾﾝｻ:C",
"ｾﾝｻ:D"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2375",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌｨｰﾀﾞｰｾﾝｻ位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6153",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ調整2",
"WorkItems": [
"■1. ①と②の投光光軸が受光ｾﾝｻの中央になる様調整する",
"2. ①の残りのｾﾝｻ･ｷｯﾄを同様の手順で調整固定する"
],
"WorkPoints": [
"ﾋﾞｰﾑ光量が治具穴で絞られ無い様に光軸を調整",
"全ての対のｾﾝｻｰを調整する",
"調整後は､治具から取り外し対のｾﾝｻｰを一つにまとめておく",
"【厳守】 ｺﾈｸﾀｰ接続時は治具の電源は(OFF)",
"この作業については､ｾﾝｻｰA･B･C･Dの順で順次調整を行い締結を行う事※ｾﾝｻｰ間のｽｷﾏが小さくﾄﾙｸﾄﾞﾗｲﾊﾞｰか入らない為",
"光軸を中央に合わせる事",
"4本のﾎﾞﾙﾄで光軸を調整する"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m",
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "WEPJ-G002-C16",
"InspectionItems": [
"検査表①:ﾃｰﾌﾟ浮き検出ｾﾝｻｰの光軸調整"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"■安全作業",
"WEPJ-G002-C16"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6153",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C16",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ調整2",
"WorkItems": [
"■1. ①と②の投光光軸が受光ｾﾝｻの中央になる様調整する",
"2. ①の残りのｾﾝｻ･ｷｯﾄを同様の手順で調整固定する"
],
"WorkPoints": [
"ﾋﾞｰﾑ光量が治具穴で絞られ無い様に光軸を調整",
"全ての対のｾﾝｻｰを調整する",
"調整後は､治具から取り外し対のｾﾝｻｰを一つにまとめておく",
"【厳守】 ｺﾈｸﾀｰ接続時は治具の電源は(OFF)",
"この作業については､ｾﾝｻｰA･B･C･Dの順で順次調整を行い締結を行う事※ｾﾝｻｰ間のｽｷﾏが小さくﾄﾙｸﾄﾞﾗｲﾊﾞｰか入らない為",
"光軸を中央に合わせる事",
"4本のﾎﾞﾙﾄで光軸を調整する"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m",
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:ﾃｰﾌﾟ浮き検出ｾﾝｻｰの光軸調整",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2375",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ調整2",
"WorkItems": [
"■1. ①と②の投光光軸が受光ｾﾝｻの中央になる様調整する",
"2. ①の残りのｾﾝｻ･ｷｯﾄを同様の手順で調整固定する"
],
"WorkPoints": [
"ﾋﾞｰﾑ光量が治具穴で絞られ無い様に光軸を調整",
"全ての対のｾﾝｻｰを調整する",
"調整後は､治具から取り外し対のｾﾝｻｰを一つにまとめておく",
"【厳守】 ｺﾈｸﾀｰ接続時は治具の電源は(OFF)",
"この作業については､ｾﾝｻｰA･B･C･Dの順で順次調整を行い締結を行う事※ｾﾝｻｰ間のｽｷﾏが小さくﾄﾙｸﾄﾞﾗｲﾊﾞｰか入らない為",
"光軸を中央に合わせる事",
"4本のﾎﾞﾙﾄで光軸を調整する"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m",
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:ﾃｰﾌﾟ浮き検出ｾﾝｻｰの光軸調整",
"■安全作業",
"WEPJ-G002-C16"
]
} | {
"QualityItem": "光軸確認",
"ToolManageNo": "FM-2375",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｻﾞｸﾞﾘφ5からﾋﾞｰﾑがはみ出さないこと",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C16",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃｰﾌﾟ浮きｾﾝｻ束線ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6127",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ配線固定",
"WorkItems": [
"1. ①②を㉗で固定する"
],
"WorkPoints": [
"ﾌﾛﾝﾄ､ﾘｱ､各2個ｾｯﾄ製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"㉘に巻き付けて整線する事",
"㉘に巻き付けて整線する事",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6127",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板・警告ﾗﾍﾞﾙ貼付①",
"WorkItems": [
"1. COVER へ⑥を貼付ける"
],
"WorkPoints": [
"⑥を貼付ける前に㉖で脱脂の事",
"指示寸法±1mmで貼付けの事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"20mm",
"20mm"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板・警告ﾗﾍﾞﾙ貼付②",
"WorkItems": [
"1. BRACKET BRACKET へLABEL を貼付ける"
],
"WorkPoints": [
"LABEL を貼付ける前に㉖で脱脂の事",
"指示寸法±1mmで貼付けの事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"5mm",
"5mm",
"5mm",
"5mm",
"5mm",
"5mm",
"5mm",
"5mm"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品準備1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りの部材が準備出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立①",
"WorkItems": [
"1. PLATE にBOLT を取付(4箇所)"
],
"WorkPoints": [
"A側から見て左側に面取りがくる事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立②",
"WorkItems": [
"1. ①にSPACER を取付",
"2. 1完成品にPLATE を取付"
],
"WorkPoints": [
"表裏があるので注意M3ﾀｯﾌﾟの位置で確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"この作業では同じものを2個製作",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立③",
"WorkItems": [
"2. 1完成品にｽﾌﾟﾘﾝｸﾞ挿入",
"◆1. ①とSPRING にｸﾞﾘｰｽ塗布",
"3. NUT で締結する"
],
"WorkPoints": [
"⑤の出代:20㎜",
"ｽﾌﾟﾘﾝｸﾞの両端面に塗布すること",
"①のｼｬﾌﾄ部分に塗布"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"Cﾘﾝｸﾞ",
"Cﾘﾝｸﾞ",
"ｸﾞﾘｰｽ塗布:小豆1",
"この作業では同じものを2個製作",
"◆作業者安全作業",
"この作業では同じものを2個製作",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "BOX12㎜",
"ToolOther": "20N･m",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立③",
"WorkItems": [
"2. 1完成品にｽﾌﾟﾘﾝｸﾞ挿入",
"3. NUT で締結する"
],
"WorkPoints": [
"⑤の出代:20㎜"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"Cﾘﾝｸﾞ",
"Cﾘﾝｸﾞ",
"この作業では同じものを2個製作",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞﾛｱｺﾈｸﾀ組立治具",
"Size": "",
"ToolOther": "FM-2324",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立③",
"WorkItems": [
"2. 1完成品にｽﾌﾟﾘﾝｸﾞ挿入",
"3. NUT で締結する"
],
"WorkPoints": [
"⑤の出代:20㎜"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"Cﾘﾝｸﾞ",
"Cﾘﾝｸﾞ",
"この作業では同じものを2個製作",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2324",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞﾛｱｺﾈｸﾀ位置調整治具(本体側):NPM",
"Size": "",
"ToolOther": "FM-2130",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立④",
"WorkItems": [
"1. ㉖にCOUPLER を差込む",
"2. ③を治具に取付､BOLT で締結"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立④",
"WorkItems": [
"1. ㉖にCOUPLER を差込む",
"3. 2完成品にJOINT を取付",
"2. ③を治具に取付､BOLT で締結"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 4N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"Cﾘﾝｸﾞ",
"Cﾘﾝｸﾞ",
"この作業では同じものを2個製作",
"この作業では同じものを2個製作",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "4N･m",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立④",
"WorkItems": [
"3. 2完成品にJOINT を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "4N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞﾛｱｺﾈｸﾀ位置調整治具(本体側):NPM",
"Size": "",
"ToolOther": "FM-2130",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑤",
"WorkItems": [
"1. ③を㉖ごと反転させる",
"2. SPACER を左右2箇所に差込む",
"3. BOLT で左右2箇所を締結"
],
"WorkPoints": [
"ﾏｰｷﾝｸﾞは治具を外して実施する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"反転",
"この作業では同じものを2個製作",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑤",
"WorkItems": [
"1. ③を㉖ごと反転させる",
"2. SPACER を左右2箇所に差込む",
"3. BOLT で左右2箇所を締結"
],
"WorkPoints": [
"⑤の出代:20㎜",
"左右2箇所",
"左右2箇所",
"ﾏｰｷﾝｸﾞは治具を外して実施する事"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"Cﾘﾝｸﾞ",
"Cﾘﾝｸﾞ",
"反転",
"この作業では同じものを2個製作",
"この作業では同じものを2個製作",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾞﾛｱｺﾈｸﾀ位置調整治具(本体側):NPM",
"Size": "",
"ToolOther": "FM-2130",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑥",
"WorkItems": [
"1. ①を反転させて､治具を取り外す",
"2. PLATE を挿入し裏からBOLT で締結"
],
"WorkPoints": [
"ﾌﾟﾚｰﾄの傾きは目視で真っすぐ合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑥",
"WorkItems": [],
"WorkPoints": [
"⑤の出代:20㎜",
"治具取り外し",
"裏側よりBOLT で各2箇所締結"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"Cﾘﾝｸﾞ",
"Cﾘﾝｸﾞ",
"反転",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀ組立⑦",
"WorkItems": [
"1. TUBE に㉘で30ｍｍ切り目を入れる",
"2. ②に1完成品を被せる(4箇所)",
"3. ｲﾝｼｭﾛｯｸで固定(4箇所)",
"1. TUBE に㉘で30ｍｍ切り目を入れる",
"2. ②に1完成品を被せる(4箇所)",
"3. ｲﾝｼｭﾛｯｸで固定(4箇所)"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"30mm",
"65mm",
"この作業では同じものを2個製作",
"この作業では同じものを2個製作",
"30mm",
"65mm",
"この作業では同じものを2個製作",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品準備2",
"WorkItems": [
"1. SPACER を次工程に払い出し"
],
"WorkPoints": [
"⑤の出代:20㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"Cﾘﾝｸﾞ",
"Cﾘﾝｸﾞ"
]
} | {
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りの部材が準備出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷③",
"WorkItems": [
"1. ①から部品ﾄﾚｲを取外し､CUSHION に梱包する",
"2. BLOCK SHEET をBAG 袋に入れ､1の完成品のｴｱｰﾏｯﾄにﾃｰﾌﾟで貼付け､PACKING-MATERIAL に収納"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "付属品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り収納出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷③",
"WorkItems": [
"1. ①から部品ﾄﾚｲを取外し､CUSHION に梱包する",
"2. BLOCK SHEET をBAG 袋に入れ､1の完成品のｴｱｰﾏｯﾄにﾃｰﾌﾟで貼付け､PACKING-MATERIAL に収納"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "付属品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り収納出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷①",
"WorkItems": [
"◆1. 指定箇所に防錆処理を行う"
],
"WorkPoints": [
"X,Y,Z軸のLM､ﾎﾞｰﾙﾈｼﾞにｸﾞﾘｰｽ塗布",
"X軸:左右に移動させて塗布",
"Y軸:前後に移動させて塗布",
"Z軸:上下に移動させて塗布",
"上下ﾘﾆｱ",
"ﾎﾞｰﾙﾈｼﾞ",
"ｸﾞﾘｰｽ塗布は海外出荷時のみ対応の事(国内不要)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:各1"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "",
"WorkName": "出荷②",
"WorkItems": [
"1. ①にBRACKET をBOLT BOLT で取付",
"2. 1.完成品にLABEL とLABEL or LABEL を貼付ける"
],
"WorkPoints": [
"X,Y,Z軸はBRACKET を取付出来る位置に移動させ取付を行う事",
"BRACKET の取付位置に注意(図参照)",
"貼付箇所㉚で拭き取り貼付ける事",
"寸法や方向に注意して貼付ける事",
"LABEL 本標識は中国への出荷機のみに貼付ける事",
"LABEL 本標識は英国への出荷機のみに貼付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"or"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "出荷②",
"WorkItems": [
"1. ①にBRACKET をBOLT BOLT で取付"
],
"WorkPoints": [
"X,Y,Z軸はBRACKET を取付出来る位置に移動させ取付を行う事",
"BRACKET の取付位置に注意(図参照)"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "出荷②",
"WorkItems": [
"2. 1.完成品にLABEL とLABEL or LABEL を貼付ける"
],
"WorkPoints": [
"貼付箇所㉚で拭き取り貼付ける事",
"寸法や方向に注意して貼付ける事",
"LABEL 本標識は中国への出荷機のみに貼付ける事",
"LABEL 本標識は英国への出荷機のみに貼付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"or"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷④",
"WorkItems": [
"1. 電源部保護",
"2. ①に②CUSHION を同梱し､BAG で包み込む"
],
"WorkPoints": [
"BAG の余剰部分は折り畳み､ﾃｰﾌﾟで見栄えよく貼付ける事",
"ACｲﾝﾚｯﾄｸﾗﾝﾌﾟに無理な力がかからない様に注意",
"②を①に入れる際､隙間をCUSHION で調整し､動かないように側壁に当付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾎﾟﾘ袋"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷⑤",
"WorkItems": [
"◆1. ①をPACKING-MATERIAL PACKING-MATERIAL に載せる"
],
"WorkPoints": [
"①は重量物の為､4人作業で行う事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物4人作業",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷⑥",
"WorkItems": [
"1. ①をPACKING-MATERIAL PACKING-MATERIAL TAPE PACKING-MATERIAL で梱包"
],
"WorkPoints": [
"PACKING-MATERIAL PACKING-MATERIAL の向きに注意(下図参照)",
"PACKING-MATERIAL を被せた後､PACKING-MATERIAL を載せる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘｻｲｸﾙﾏｰｸ(CB)",
"積層材が1箇所大きい"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷⑦",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. ①をSTOPPER BAND で固定",
"STOPPER BAND 位置に注意(下図参照)",
"BAND にたわみ･よじれなど無く､しっかりと固定されている事",
"底面のﾊﾞﾝﾄﾞ穴にBAND を通す事",
"写真の様に輪っかを作り､BAND を固定後ﾃｰﾌﾟでとめる"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示された位置で結束が出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "出荷⑧",
"WorkItems": [
"1. ①に㉖のラベルを貼付"
],
"WorkPoints": [
"ﾗﾍﾞﾙの貼付位置に注意(下図参照)",
"30mm",
"150mm",
"荷扱い指示",
"ﾘｻｲｸﾙﾏｰｸ",
"ｷｯﾄ銘板",
"ｷｯﾄ銘板は外装箱の底から150mmにする事",
"ｼｯﾋﾟﾝｸﾞﾘｰｽﾄに名称と品番が記される場合ｷｯﾄ銘板の貼付けは不要"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"kg",
"対角(反対側)も同じ表示有り",
"対角(反対側)も同じ表示有り",
"対角(反対側)も同じ寸法で貼付"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "Dﾋﾟﾝ圧入治具",
"Size": "",
"ToolOther": "FM-2386",
"WorkName": "ﾏｶﾞｼﾞﾝﾘﾌﾀｰ部(ｼﾝｸﾞﾙﾏｶﾞｼﾞﾝ)組立①",
"WorkItems": [
"1. STAND にPIN を圧入する"
],
"WorkPoints": [
"出代:5㎜",
"出代:5㎜",
"出代に注意する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝﾘﾌﾀｰ部(ｼﾝｸﾞﾙﾏｶﾞｼﾞﾝ)組立①",
"WorkItems": [
"1. STAND にPIN を圧入する"
],
"WorkPoints": [
"出代:5㎜",
"出代:5㎜",
"出代に注意する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "5.0±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝﾘﾌﾀｰ部(ｼﾝｸﾞﾙﾏｶﾞｼﾞﾝ)組立②",
"WorkItems": [
"1. BRACKET にSPACER WASHER を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝﾘﾌﾀｰ部(ｼﾝｸﾞﾙﾏｶﾞｼﾞﾝ)組立③",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝﾘﾌﾀｰ部(ｼﾝｸﾞﾙﾏｶﾞｼﾞﾝ)引渡し",
"WorkItems": [
"1. ①とBOLT WASHER を次工程に引渡す"
],
"WorkPoints": [
"参考図(ﾏｶﾞｼﾞﾝﾘﾌﾀｰ､ﾎﾙﾀﾞｰとの合体)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "引渡確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引渡し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本加圧ｼｰﾄ廃棄部取付け①",
"WorkItems": [
"1. ①に⑥を付属ﾎﾞﾙﾄで取付ける"
],
"WorkPoints": [
"付属ﾎﾞﾙﾄで取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾎﾞﾙﾄ M6×12(2P) ﾎﾞﾙﾄ M6×25(1P) 厚肉座金 M6(3P)",
"M6×25,厚肉座金M6",
"M6×12,厚肉座金M6",
"設備後側"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本加圧ｼｰﾄ廃棄部取付け②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "前面ｶﾊﾞｰ取付①",
"WorkItems": [
"1. ①に⑥⑦⑧をSCREW WASHER 取付ける"
],
"WorkPoints": [
"塗装無し面:導通確保の為WASHER 無し"
],
"Tolks": [
"その他の箇所:締付ﾄﾙｸ160cN･m",
"U溝部:締付ﾄﾙｸ120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "前面ｶﾊﾞｰ取付①",
"WorkItems": [
"1. ①に⑥⑦⑧をSCREW WASHER 取付ける"
],
"WorkPoints": [
"塗装無し面:導通確保の為WASHER 無し"
],
"Tolks": [
"その他の箇所:締付ﾄﾙｸ160cN･m",
"U溝部:締付ﾄﾙｸ120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "後面ｶﾊﾞｰ取付①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. ①に⑥⑦⑧をSCREW WASHER で取付ける",
"塗装無し面:導通確保の為WASHER 無し",
"その他の箇所:締付ﾄﾙｸ160cN･m",
"U溝部:締付ﾄﾙｸ120cN･m"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "後面ｶﾊﾞｰ取付①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. ①に⑥⑦⑧をSCREW WASHER で取付ける",
"塗装無し面:導通確保の為WASHER 無し",
"その他の箇所:締付ﾄﾙｸ160cN･m",
"U溝部:締付ﾄﾙｸ120cN･m"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "右側面ｶﾊﾞｰ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. ①に⑥をSCREW WASHER 取付ける",
"締付ﾄﾙｸ 160cN･m",
"塗装無し面:導通確保の為WASHER 無し"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "前面ｶﾊﾞｰ取付②",
"WorkItems": [
"1. ①に⑥をSCREW WASHER 取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "後面ｶﾊﾞｰ取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. ①に⑥⑦をSCREW WASHER で取付ける",
"締付ﾄﾙｸ 160cN･m"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "後面ﾒﾝﾃﾅﾝｽｶﾊﾞｰ取付",
"WorkItems": [
"1. ①に⑥を取付ける"
],
"WorkPoints": [
"取付け済のﾎﾞﾙﾄで取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "仮置きｶﾊﾞｰ(R)取付①",
"WorkItems": [
"1. ①に⑥⑦をSCREW WASHER で取付ける"
],
"WorkPoints": [
"塗装無し面:導通確保の為⑬無し",
"仮置きﾕﾆｯﾄを取付時に実施する"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"S211"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "仮置きｶﾊﾞｰ(R)取付②",
"WorkItems": [
"1. ①に⑥⑦をSCREW WASHER で取付ける"
],
"WorkPoints": [
"仮置きﾕﾆｯﾄを取付時に実施する"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "仮置きｶﾊﾞｰ(R)取付③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. ①に⑥COVER をSCREW WASHER で取付ける",
"締付ﾄﾙｸ 160cN･m",
"塗装無し面:導通確保の為WASHER 無し",
"仮置きﾕﾆｯﾄを取付時に実施する"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "本体ﾚﾍﾞﾙ高さ出しAM(連結)",
"WorkItems": [
"2. 架台のﾚﾍﾞﾙを調整する"
],
"WorkPoints": [
"規格:605mm±5mm以内",
"規格:0.06mm以内"
],
"Tolks": [],
"InspectionNo": "WWYJ-5500-002",
"InspectionItems": [
"検査表①:本体ﾚﾍﾞﾙ高さ出し"
],
"WorkTypes": [],
"Words": [
"架台高さ 605mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "架台上面高さ605㎜±5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3m",
"ToolOther": "",
"WorkName": "本体ﾚﾍﾞﾙ高さ出しAM(連結)",
"WorkItems": [
"2. 架台のﾚﾍﾞﾙを調整する"
],
"WorkPoints": [
"規格:605mm±5mm以内",
"規格:0.06mm以内"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"架台高さ 605mm",
"検査表①:本体ﾚﾍﾞﾙ高さ出し",
"WWYJ-5500-002"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "水準器",
"Size": "0.02㎜/目盛",
"ToolOther": "",
"WorkName": "本体ﾚﾍﾞﾙ高さ出しAM(連結)",
"WorkItems": [
"2. 架台のﾚﾍﾞﾙを調整する"
],
"WorkPoints": [
"規格:605mm±5mm以内",
"規格:0.06mm以内"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"架台高さ 605mm",
"検査表①:本体ﾚﾍﾞﾙ高さ出し",
"WWYJ-5500-002"
]
} | {
"QualityItem": "水準確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "XY=0.06㎜以下",
"Method": "水準器",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "本体ﾚﾍﾞﾙ高さ出しP1(連結)",
"WorkItems": [],
"WorkPoints": [
"連結ﾌﾞﾛｯｸ間に隙間が無い事",
"架台水準_規格:0.06mm以内",
"架台の高さ※AM架台と合わせる"
],
"Tolks": [],
"InspectionNo": "WWYJ-5500-002",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"P1架台水準器設置個所"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "架台高さAM架台と合わせる",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体ﾚﾍﾞﾙ高さ出しP1(連結)",
"WorkItems": [
"1. AM架台にP1架台を近づけ仮ﾚﾍﾞﾙ調整を行う｡(架台の高さはAMに合わせる)",
"2. ｱｼﾞｬｽﾄﾎﾞﾙﾄにｽﾗｲﾃﾞｨﾝｸﾞﾍﾟｰﾊﾟｰを敷きP1架台をAM架台に寄せる｡",
"3.P1架台のﾚﾍﾞﾙ調整を行いながら連結ﾌﾞｯﾛｸでAMPの連結を行う｡"
],
"WorkPoints": [
"連結ﾌﾞﾛｯｸ間に隙間が無い事",
"架台水準_規格:0.06mm以内",
"架台の高さ※AM架台と合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:本体ﾚﾍﾞﾙ高さ出し",
"P1架台水準器設置個所",
"AM",
"P1",
"ｽﾗｲﾃﾞｨﾝｸﾞﾍﾟｰﾊﾟｰ",
"AM",
"P1",
"AM",
"P1",
"P1",
"AM",
"WWYJ-5500-002"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "連結ﾌﾞﾛｯｸに隙間無い事",
"Method": "目視",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "水準器",
"Size": "0.02㎜/目盛",
"ToolOther": "",
"WorkName": "本体ﾚﾍﾞﾙ高さ出しP1(連結)",
"WorkItems": [],
"WorkPoints": [
"連結ﾌﾞﾛｯｸ間に隙間が無い事",
"架台水準_規格:0.06mm以内",
"架台の高さ※AM架台と合わせる",
"連結ﾌﾞﾛｯｸ間に隙間が無い事",
"架台水準_規格:0.06mm以内",
"架台の高さ※AM架台と合わせる",
"連結ﾌﾞﾛｯｸ間に隙間が無い事",
"架台水準_規格:0.06mm以内",
"架台の高さ※AM架台と合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"P1架台水準器設置個所",
"P1架台水準器設置個所",
"P1架台水準器設置個所",
"WWYJ-5500-002"
]
} | {
"QualityItem": "水準確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "XY=0.06㎜以下",
"Method": "水準器",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "本体ﾚﾍﾞﾙ高さ出しP2(連結)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5500-002",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"P2架台水準器設置個所"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "架台高さP1架台と合わせる",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体ﾚﾍﾞﾙ高さ出しP2(連結)",
"WorkItems": [
"1. AM架台にP1架台を近づけ仮ﾚﾍﾞﾙ調整を行う｡(架台の高さはAMに合わせる)",
"2. ｱｼﾞｬｽﾄﾎﾞﾙﾄにｽﾗｲﾃﾞｨﾝｸﾞﾍﾟｰﾊﾟｰを敷きP2架台をP1架台に寄せる｡",
"3.P2架台のﾚﾍﾞﾙ調整を行いながら連結ﾌﾞｯﾛｸでP1との連結を行う｡"
],
"WorkPoints": [
"連結ﾌﾞﾛｯｸ間に隙間が無い事",
"架台水準_規格:0.06mm以内",
"架台の高さ※P1架台と合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"AM",
"P1",
"P2",
"AM",
"P1",
"P2",
"検査表①:本体ﾚﾍﾞﾙ高さ出し",
"P2架台水準器設置個所",
"ｽﾗｲﾃﾞｨﾝｸﾞﾍﾟｰﾊﾟｰ",
"AM",
"P1",
"P1",
"AM",
"P2",
"WWYJ-5500-002"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "連結ﾌﾞﾛｯｸに隙間無い事",
"Method": "目視",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "水準器",
"Size": "0.02㎜/目盛",
"ToolOther": "",
"WorkName": "本体ﾚﾍﾞﾙ高さ出しP2(連結)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"P2架台水準器設置個所",
"P2架台水準器設置個所",
"WWYJ-5500-002"
]
} | {
"QualityItem": "水準確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "XY=0.06㎜以下",
"Method": "水準器",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体連結(配線、配管)①",
"WorkItems": [
"1. AM-P1間の配線､配管を接続する｡(架台側面の抜き穴を通す)"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"AM前面",
"P1前面",
"①CPUｰBOX",
"②AM connecter bracket",
"③P1 RING負荷(K3011)",
"P2",
"P1からの配管接続"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本体連結(配線、配管)②",
"WorkItems": [
"1. P1-P2間の配線､配管を接続する｡(架台側面の抜き穴を通す)"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"P2",
"P1背面",
"P1前面",
"①P1背面RING負荷K3003",
"② 連結ｺﾈｸﾀﾌﾞﾗｹｯﾄ",
"③ P1 RING負荷(K300A)",
"P2前面",
"P2からの配管接続",
"P1(背面)"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "電源接続確認",
"WorkItems": [
"1. 設備後面電源ｶﾊﾞｰを外す",
"■2. 電源ｶﾊﾞｰ上面の丸穴より電源ｹｰﾌﾞﾙを入れ込み端子台の所定位置へ接続",
"3. 設備側にｴｱｰﾎｰｽ/真空ﾎｰｽを接続する",
"4. 真空ﾎﾟﾝﾌﾟの電源ON",
"5. 工場側にｴｱｰﾎｰｽ/電源ｹｰﾌﾞﾙを接続する",
"6. 設備のｴｱｰｺｯｸON",
"7. 設備の電源ON"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 250cN･m",
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "WWYJ-5500-002",
"InspectionItems": [
"検査表①:電源接続確認"
],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"※締付ﾄﾙｸ:電源線(赤･白･黒) 250cN･m ｱｰｽ線 180cN･m",
"WWYJ-5500-002"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "250cN･m",
"WorkName": "電源接続確認",
"WorkItems": [
"1. 設備後面電源ｶﾊﾞｰを外す",
"■2. 電源ｶﾊﾞｰ上面の丸穴より電源ｹｰﾌﾞﾙを入れ込み端子台の所定位置へ接続"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 250cN･m",
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"※締付ﾄﾙｸ:電源線(赤･白･黒) 250cN･m ｱｰｽ線 180cN･m",
"検査表①:電源接続確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "電源接続確認",
"WorkItems": [
"1. 設備後面電源ｶﾊﾞｰを外す",
"■2. 電源ｶﾊﾞｰ上面の丸穴より電源ｹｰﾌﾞﾙを入れ込み端子台の所定位置へ接続"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 250cN･m",
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"※締付ﾄﾙｸ:電源線(赤･白･黒) 250cN･m ｱｰｽ線 180cN･m",
"検査表①:電源接続確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒｲﾝｴｱｰ/ﾒｲﾝ真空圧設定",
"WorkItems": [
"1. ｶﾊﾞｰを外し､ﾒｲﾝｴｱｰ圧の設定を行う(正圧)",
"2. ﾒｲﾝ真空圧設定を行う(負圧)"
],
"WorkPoints": [
"設備ﾒｲﾝｴｱｰを投入し,ﾚｷﾞｭﾚｰﾀで設定になるよう調整する",
"規格:0.45MPa±0.03MPa",
"設備ﾒｲﾝ真空を投入し､ﾚｷﾞｭﾚｰﾀで設定になるよう調整する(真空1/真空2)",
"規格:-80KPa以下"
],
"Tolks": [],
"InspectionNo": "WWYJ-5500-002",
"InspectionItems": [
"検査表①:ﾒｲﾝｴｱｰ/ﾒｲﾝ真空圧設定",
"検査表①:ﾒｲﾝｴｱｰ/ﾒｲﾝ真空圧設定"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｾﾝｻｰ表示を参照しながら調整",
"ﾒｲﾝ真空ﾚｷﾞｭﾚｰﾀ真空1真空2",
"ｾﾝｻｰ表示を参照しながら調整",
"ﾒｲﾝｴｱｰﾚｷﾞｭﾚｰﾀ",
"WWYJ-5500-002"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾒｲﾝｴｱ(正圧)0.45MPa±0.03",
"Method": "目視",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒｲﾝｴｱｰ/ﾒｲﾝ真空圧設定",
"WorkItems": [
"1. ｶﾊﾞｰを外し､ﾒｲﾝｴｱｰ圧の設定を行う(正圧)",
"2. ﾒｲﾝ真空圧設定を行う(負圧)"
],
"WorkPoints": [
"設備ﾒｲﾝｴｱｰを投入し,ﾚｷﾞｭﾚｰﾀで設定になるよう調整する",
"規格:0.45MPa±0.03MPa",
"設備ﾒｲﾝ真空を投入し､ﾚｷﾞｭﾚｰﾀで設定になるよう調整する(真空1/真空2)",
"規格:-80KPa以下"
],
"Tolks": [],
"InspectionNo": "WWYJ-5500-002",
"InspectionItems": [
"検査表①:ﾒｲﾝｴｱｰ/ﾒｲﾝ真空圧設定",
"検査表①:ﾒｲﾝｴｱｰ/ﾒｲﾝ真空圧設定"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｾﾝｻｰ表示を参照しながら調整",
"ﾒｲﾝ真空ﾚｷﾞｭﾚｰﾀ真空1真空2",
"ｾﾝｻｰ表示を参照しながら調整",
"ﾒｲﾝｴｱｰﾚｷﾞｭﾚｰﾀ",
"WWYJ-5500-002"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾒｲﾝ真空(負圧)-80kPa以下",
"Method": "目視",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "付属品確認",
"WorkItems": [
"1. 付属品ﾘｽﾄを基に付属品の有無確認を実施する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"付属品ﾘｽﾄ一覧(表紙) (本体)",
"●付属品明細(A)FPX005CG 標準部",
"●付属品明細(B)FPX005CG ｵﾌﾟｼｮﾝ部",
"●付属品明細(C)機種切替部品",
"●(D)FPX005CG 標準工具ｾｯﾄ",
"●(F)制御ｵﾌﾟｼｮﾝ部",
"検査表①:付属品確認",
"WWYJ-5500-002"
]
} | {
"QualityItem": "物品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾘｽﾄの物がある事",
"Method": "目視",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "個別仕様/選択仕様確認",
"WorkItems": [
"1. 仕様ﾁｪｯｸﾘｽﾄを基に仕様確認を行う(集約仕様書を参照の上､仕様確認)"
],
"WorkPoints": [
"お客様個別に設備仕様が異なるので工事機番を間違えないよう集約仕様書を基に確認を行う事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:個別仕様選択仕様確認",
"WWYJ-5500-002"
]
} | {
"QualityItem": "仕様確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾘｽﾄ通りの仕様である事",
"Method": "目視",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PE結合試験機",
"Size": "",
"ToolOther": "",
"WorkName": "絶縁・耐圧・PE結合試験",
"WorkItems": [
"■1. 絶縁･耐圧･PE結合試験を行う"
],
"WorkPoints": [
"安全工程試験検査表に基き検査を行う"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:絶縁･耐圧･PE結合試験",
"WWYJ-5500-002"
]
} | {
"QualityItem": "電気試験確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "PE結合試験機台帳",
"StdVal": "試験機判定",
"Method": "PE結合試験機",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "絶縁耐圧試験機",
"Size": "",
"ToolOther": "",
"WorkName": "絶縁・耐圧・PE結合試験",
"WorkItems": [
"■1. 絶縁･耐圧･PE結合試験を行う"
],
"WorkPoints": [
"安全工程試験検査表に基き検査を行う"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:絶縁･耐圧･PE結合試験",
"WWYJ-5500-002"
]
} | {
"QualityItem": "電気試験確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "絶縁耐圧試験台帳",
"StdVal": "試験機判定",
"Method": "絶縁耐圧試験機",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ACF圧力測定治具",
"Size": "",
"ToolOther": "FM-3269",
"WorkName": "ACF貼付部圧力測定1",
"WorkItems": [
"2. 【ﾃﾞｰﾀ管理ﾒﾆｭｰ】-【ﾏｼﾝﾃﾞｰﾀ編集】-【ﾌﾟﾛｾｽﾃﾞｰﾀ荷重】-【ﾌﾟﾛｾｽ確認荷重】-【A】-【ﾕｰｻﾞｰ設定ﾌﾟﾛｾｽ条件】-軸関係の退避を行う",
"1. ﾛｰﾄﾞｾﾙとｱﾝﾌﾟを接続しｱﾝﾌﾟの設定を行う(治具取付け)",
"3. ACFﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞの取外し治具をｾｯﾄする",
"4. 【荷重確認時間】:2s､【繰り返し回数】:3回､【ﾍｯﾄﾞL荷重】:20､90､160Nの3条件を設定し､ﾚｷﾞｭﾚｰﾀを左下数値に設定"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5500-002",
"InspectionItems": [
"検査表①:ACF貼付部圧力測定"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"①ﾛｰﾄﾞｾﾙとｱﾝﾌﾟ接続②ﾒｼﾞｬｰSWに設定③ｾｯﾄﾎﾞﾀﾝを長押し､F-1を表示④再度､ｾｯﾄﾎﾞﾀﾝを長押し､ｾﾞﾛﾎﾞﾀﾝを押し､ 小数点が下3桁目にくるようにｾﾞﾛﾎﾞﾀﾝで設定 設定後､ｾｯﾄﾎﾞﾀﾝ長押し⑤ﾋﾟｰｸﾎｰﾙﾄﾞﾎﾞﾀﾝを押して F-3を表示させる⑥ｾｯﾄﾎﾞﾀﾝ長押し､ﾛｰﾄﾞｾﾙのひずみ値( mV/V) の数字をｾﾞﾛﾎﾞﾀﾝ･ﾋﾟｰｸﾎｰﾙﾄﾞﾎﾞﾀﾝで入力後､ｾｯﾄﾎﾞﾀﾝ長押し⑦ﾛｰﾄﾞｾﾙの定格荷重(N)を入力後､ｾｯﾄﾎﾞﾀﾝ長押し⑧荷重の小数点の位置をｾﾞﾛﾎﾞﾀﾝで設定後､ｾｯﾄﾎﾞﾀﾝ長押し⑨ｾﾞﾛﾎﾞﾀﾝを長押し､LEDを点灯させたら完了",
"圧力治具",
"ﾛｰﾄﾞｾﾙｱﾝﾌﾟ",
"200Nﾛｰﾄﾞｾﾙ",
"ﾋｰﾀ温度は制御停止で測定する事",
"ｱﾝﾌﾟ設定方法",
"WWYJ-5500-002"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-3269",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "正常な事",
"Method": "ACF圧力測定治具",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾛｰﾄﾞｾﾙ",
"Size": "",
"ToolOther": "200N",
"WorkName": "ACF貼付部圧力測定1",
"WorkItems": [
"2. 【ﾃﾞｰﾀ管理ﾒﾆｭｰ】-【ﾏｼﾝﾃﾞｰﾀ編集】-【ﾌﾟﾛｾｽﾃﾞｰﾀ荷重】-【ﾌﾟﾛｾｽ確認荷重】-【A】-【ﾕｰｻﾞｰ設定ﾌﾟﾛｾｽ条件】-軸関係の退避を行う",
"1. ﾛｰﾄﾞｾﾙとｱﾝﾌﾟを接続しｱﾝﾌﾟの設定を行う(治具取付け)",
"3. ACFﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞの取外し治具をｾｯﾄする",
"4. 【荷重確認時間】:2s､【繰り返し回数】:3回､【ﾍｯﾄﾞL荷重】:20､90､160Nの3条件を設定し､ﾚｷﾞｭﾚｰﾀを左下数値に設定"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"①ﾛｰﾄﾞｾﾙとｱﾝﾌﾟ接続②ﾒｼﾞｬｰSWに設定③ｾｯﾄﾎﾞﾀﾝを長押し､F-1を表示④再度､ｾｯﾄﾎﾞﾀﾝを長押し､ｾﾞﾛﾎﾞﾀﾝを押し､ 小数点が下3桁目にくるようにｾﾞﾛﾎﾞﾀﾝで設定 設定後､ｾｯﾄﾎﾞﾀﾝ長押し⑤ﾋﾟｰｸﾎｰﾙﾄﾞﾎﾞﾀﾝを押して F-3を表示させる⑥ｾｯﾄﾎﾞﾀﾝ長押し､ﾛｰﾄﾞｾﾙのひずみ値( mV/V) の数字をｾﾞﾛﾎﾞﾀﾝ･ﾋﾟｰｸﾎｰﾙﾄﾞﾎﾞﾀﾝで入力後､ｾｯﾄﾎﾞﾀﾝ長押し⑦ﾛｰﾄﾞｾﾙの定格荷重(N)を入力後､ｾｯﾄﾎﾞﾀﾝ長押し⑧荷重の小数点の位置をｾﾞﾛﾎﾞﾀﾝで設定後､ｾｯﾄﾎﾞﾀﾝ長押し⑨ｾﾞﾛﾎﾞﾀﾝを長押し､LEDを点灯させたら完了",
"圧力治具",
"ﾛｰﾄﾞｾﾙｱﾝﾌﾟ",
"200Nﾛｰﾄﾞｾﾙ",
"ﾋｰﾀ温度は制御停止で測定する事",
"ｱﾝﾌﾟ設定方法",
"検査表①:ACF貼付部圧力測定",
"WWYJ-5500-002"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "正常な事",
"Method": "ﾛｰﾄﾞｾﾙ",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾛｰﾄﾞｾﾙｱﾝﾌﾟ",
"Size": "",
"ToolOther": "",
"WorkName": "ACF貼付部圧力測定1",
"WorkItems": [
"2. 【ﾃﾞｰﾀ管理ﾒﾆｭｰ】-【ﾏｼﾝﾃﾞｰﾀ編集】-【ﾌﾟﾛｾｽﾃﾞｰﾀ荷重】-【ﾌﾟﾛｾｽ確認荷重】-【A】-【ﾕｰｻﾞｰ設定ﾌﾟﾛｾｽ条件】-軸関係の退避を行う",
"1. ﾛｰﾄﾞｾﾙとｱﾝﾌﾟを接続しｱﾝﾌﾟの設定を行う(治具取付け)",
"3. ACFﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞの取外し治具をｾｯﾄする",
"4. 【荷重確認時間】:2s､【繰り返し回数】:3回､【ﾍｯﾄﾞL荷重】:20､90､160Nの3条件を設定し､ﾚｷﾞｭﾚｰﾀを左下数値に設定"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"①ﾛｰﾄﾞｾﾙとｱﾝﾌﾟ接続②ﾒｼﾞｬｰSWに設定③ｾｯﾄﾎﾞﾀﾝを長押し､F-1を表示④再度､ｾｯﾄﾎﾞﾀﾝを長押し､ｾﾞﾛﾎﾞﾀﾝを押し､ 小数点が下3桁目にくるようにｾﾞﾛﾎﾞﾀﾝで設定 設定後､ｾｯﾄﾎﾞﾀﾝ長押し⑤ﾋﾟｰｸﾎｰﾙﾄﾞﾎﾞﾀﾝを押して F-3を表示させる⑥ｾｯﾄﾎﾞﾀﾝ長押し､ﾛｰﾄﾞｾﾙのひずみ値( mV/V) の数字をｾﾞﾛﾎﾞﾀﾝ･ﾋﾟｰｸﾎｰﾙﾄﾞﾎﾞﾀﾝで入力後､ｾｯﾄﾎﾞﾀﾝ長押し⑦ﾛｰﾄﾞｾﾙの定格荷重(N)を入力後､ｾｯﾄﾎﾞﾀﾝ長押し⑧荷重の小数点の位置をｾﾞﾛﾎﾞﾀﾝで設定後､ｾｯﾄﾎﾞﾀﾝ長押し⑨ｾﾞﾛﾎﾞﾀﾝを長押し､LEDを点灯させたら完了",
"圧力治具",
"ﾛｰﾄﾞｾﾙｱﾝﾌﾟ",
"200Nﾛｰﾄﾞｾﾙ",
"ﾋｰﾀ温度は制御停止で測定する事",
"ｱﾝﾌﾟ設定方法",
"検査表①:ACF貼付部圧力測定",
"WWYJ-5500-002"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "正常な事",
"Method": "ﾛｰﾄﾞｾﾙｱﾝﾌﾟ",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ACF貼付部圧力測定2",
"WorkItems": [
"5. 【計測開始】を押す",
"6. 前ﾍﾟｰｼﾞの測定ﾎﾟｲﾝﾄ計測後､【換算定数自動計算】を押し､表の値を入力し､【計算実行】を押す",
"8. R側ﾍｯﾄﾞも同様に測定を行い事前ﾃﾞｰﾀを完成させる",
"7. 結果登録後､再度20､90､160Nを測定し事前ﾃﾞｰﾀへ記入する"
],
"WorkPoints": [
"規格:入力値が50N未満は±5N､50N以上は±10%"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"※計算値を結果登録し､再度､③荷重計測をする",
"検査表①:ACF貼付部圧力測定",
"WWYJ-5500-002"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "入力値の±5Nもしくは±10%の大きい方",
"Method": "目視",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "仮圧圧力測定治具",
"Size": "",
"ToolOther": "FM-3567",
"WorkName": "仮圧着部圧力測定1",
"WorkItems": [
"1. ﾛｰﾄﾞｾﾙとｱﾝﾌﾟを接続しｱﾝﾌﾟの設定を行う(治具取付け)",
"4. ﾊﾟﾗﾒｰﾀ確認",
"3. 仮圧ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞに治具をｾｯﾄする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5500-002",
"InspectionItems": [
"検査表①:仮圧着部圧力測定"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"①ﾛｰﾄﾞｾﾙとｱﾝﾌﾟ接続②ﾒｼﾞｬｰSWに設定③ｾｯﾄﾎﾞﾀﾝを長押し､F-1を表示④再度､ｾｯﾄﾎﾞﾀﾝを長押し､ｾﾞﾛﾎﾞﾀﾝを押し､ 小数点が下3桁目にくるようにｾﾞﾛﾎﾞﾀﾝで設定 設定後､ｾｯﾄﾎﾞﾀﾝ長押し⑤ﾋﾟｰｸﾎｰﾙﾄﾞﾎﾞﾀﾝを押して F-3を表示させる⑥ｾｯﾄﾎﾞﾀﾝ長押し､ﾛｰﾄﾞｾﾙのひずみ値( mV/V) の数字をｾﾞﾛﾎﾞﾀﾝ･ﾋﾟｰｸﾎｰﾙﾄﾞﾎﾞﾀﾝで入力後､ｾｯﾄﾎﾞﾀﾝ長押し⑦ﾛｰﾄﾞｾﾙの定格荷重(N)を入力後､ｾｯﾄﾎﾞﾀﾝ長押し⑧荷重の小数点の位置をｾﾞﾛﾎﾞﾀﾝで設定後､ｾｯﾄﾎﾞﾀﾝ長押し⑨ｾﾞﾛﾎﾞﾀﾝを長押し､LEDを点灯させたら完了",
"5. 治具厚み計測を行う:【押込み量】:0.2mm､【荷重確認時間】:2s､【繰り返し回数】:3回､ 【ﾍｯﾄﾞ荷重】:50N､ﾚｷﾞｭﾚｰﾀを左下数値に設定後､【治具厚み計測】を押す",
"ﾛｰﾄﾞｾﾙｱﾝﾌﾟ",
"200Nﾛｰﾄﾞｾﾙ",
"ﾋｰﾀ温度は制御停止で測定する事",
"2. 【ﾃﾞｰﾀ管理ﾒﾆｭｰ】-【ﾏｼﾝﾃﾞｰﾀ編集】-【ﾌﾟﾛｾｽﾃﾞｰﾀ荷重】-【ﾌﾟﾛｾｽ確認荷重】-【M】-【ﾕｰｻﾞｰ設定ﾌﾟﾛｾｽ条件】-軸関係の退避を行う",
"圧力治具",
"①-1 ｢部品ﾃﾞｰﾀ｣⇒｢設備動作｣⇒｢仮圧ﾍｯﾄﾞﾞ動作｣ 仮圧着速度:20mm/s①-2 ｢ﾏｼﾝﾃﾞｰﾀ｣⇒｢〔M〕仮圧着｣⇒｢仮圧ﾍｯﾄﾞ｣ 仮圧着速度距離:0.5mm",
"ｱﾝﾌﾟ設定方法",
"WWYJ-5500-002"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-3567",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "正常な事",
"Method": "仮圧圧力測定治具",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾛｰﾄﾞｾﾙ",
"Size": "",
"ToolOther": "200N",
"WorkName": "仮圧着部圧力測定1",
"WorkItems": [
"1. ﾛｰﾄﾞｾﾙとｱﾝﾌﾟを接続しｱﾝﾌﾟの設定を行う(治具取付け)",
"4. ﾊﾟﾗﾒｰﾀ確認",
"3. 仮圧ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞに治具をｾｯﾄする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"①ﾛｰﾄﾞｾﾙとｱﾝﾌﾟ接続②ﾒｼﾞｬｰSWに設定③ｾｯﾄﾎﾞﾀﾝを長押し､F-1を表示④再度､ｾｯﾄﾎﾞﾀﾝを長押し､ｾﾞﾛﾎﾞﾀﾝを押し､ 小数点が下3桁目にくるようにｾﾞﾛﾎﾞﾀﾝで設定 設定後､ｾｯﾄﾎﾞﾀﾝ長押し⑤ﾋﾟｰｸﾎｰﾙﾄﾞﾎﾞﾀﾝを押して F-3を表示させる⑥ｾｯﾄﾎﾞﾀﾝ長押し､ﾛｰﾄﾞｾﾙのひずみ値( mV/V) の数字をｾﾞﾛﾎﾞﾀﾝ･ﾋﾟｰｸﾎｰﾙﾄﾞﾎﾞﾀﾝで入力後､ｾｯﾄﾎﾞﾀﾝ長押し⑦ﾛｰﾄﾞｾﾙの定格荷重(N)を入力後､ｾｯﾄﾎﾞﾀﾝ長押し⑧荷重の小数点の位置をｾﾞﾛﾎﾞﾀﾝで設定後､ｾｯﾄﾎﾞﾀﾝ長押し⑨ｾﾞﾛﾎﾞﾀﾝを長押し､LEDを点灯させたら完了",
"5. 治具厚み計測を行う:【押込み量】:0.2mm､【荷重確認時間】:2s､【繰り返し回数】:3回､ 【ﾍｯﾄﾞ荷重】:50N､ﾚｷﾞｭﾚｰﾀを左下数値に設定後､【治具厚み計測】を押す",
"ﾛｰﾄﾞｾﾙｱﾝﾌﾟ",
"200Nﾛｰﾄﾞｾﾙ",
"ﾋｰﾀ温度は制御停止で測定する事",
"2. 【ﾃﾞｰﾀ管理ﾒﾆｭｰ】-【ﾏｼﾝﾃﾞｰﾀ編集】-【ﾌﾟﾛｾｽﾃﾞｰﾀ荷重】-【ﾌﾟﾛｾｽ確認荷重】-【M】-【ﾕｰｻﾞｰ設定ﾌﾟﾛｾｽ条件】-軸関係の退避を行う",
"圧力治具",
"①-1 ｢部品ﾃﾞｰﾀ｣⇒｢設備動作｣⇒｢仮圧ﾍｯﾄﾞﾞ動作｣ 仮圧着速度:20mm/s①-2 ｢ﾏｼﾝﾃﾞｰﾀ｣⇒｢〔M〕仮圧着｣⇒｢仮圧ﾍｯﾄﾞ｣ 仮圧着速度距離:0.5mm",
"検査表①:仮圧着部圧力測定",
"ｱﾝﾌﾟ設定方法",
"WWYJ-5500-002"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "正常な事",
"Method": "ﾛｰﾄﾞｾﾙ",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾛｰﾄﾞｾﾙｱﾝﾌﾟ",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着部圧力測定1",
"WorkItems": [
"1. ﾛｰﾄﾞｾﾙとｱﾝﾌﾟを接続しｱﾝﾌﾟの設定を行う(治具取付け)",
"4. ﾊﾟﾗﾒｰﾀ確認",
"3. 仮圧ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞに治具をｾｯﾄする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"①ﾛｰﾄﾞｾﾙとｱﾝﾌﾟ接続②ﾒｼﾞｬｰSWに設定③ｾｯﾄﾎﾞﾀﾝを長押し､F-1を表示④再度､ｾｯﾄﾎﾞﾀﾝを長押し､ｾﾞﾛﾎﾞﾀﾝを押し､ 小数点が下3桁目にくるようにｾﾞﾛﾎﾞﾀﾝで設定 設定後､ｾｯﾄﾎﾞﾀﾝ長押し⑤ﾋﾟｰｸﾎｰﾙﾄﾞﾎﾞﾀﾝを押して F-3を表示させる⑥ｾｯﾄﾎﾞﾀﾝ長押し､ﾛｰﾄﾞｾﾙのひずみ値( mV/V) の数字をｾﾞﾛﾎﾞﾀﾝ･ﾋﾟｰｸﾎｰﾙﾄﾞﾎﾞﾀﾝで入力後､ｾｯﾄﾎﾞﾀﾝ長押し⑦ﾛｰﾄﾞｾﾙの定格荷重(N)を入力後､ｾｯﾄﾎﾞﾀﾝ長押し⑧荷重の小数点の位置をｾﾞﾛﾎﾞﾀﾝで設定後､ｾｯﾄﾎﾞﾀﾝ長押し⑨ｾﾞﾛﾎﾞﾀﾝを長押し､LEDを点灯させたら完了",
"5. 治具厚み計測を行う:【押込み量】:0.2mm､【荷重確認時間】:2s､【繰り返し回数】:3回､ 【ﾍｯﾄﾞ荷重】:50N､ﾚｷﾞｭﾚｰﾀを左下数値に設定後､【治具厚み計測】を押す",
"ﾛｰﾄﾞｾﾙｱﾝﾌﾟ",
"200Nﾛｰﾄﾞｾﾙ",
"ﾋｰﾀ温度は制御停止で測定する事",
"2. 【ﾃﾞｰﾀ管理ﾒﾆｭｰ】-【ﾏｼﾝﾃﾞｰﾀ編集】-【ﾌﾟﾛｾｽﾃﾞｰﾀ荷重】-【ﾌﾟﾛｾｽ確認荷重】-【M】-【ﾕｰｻﾞｰ設定ﾌﾟﾛｾｽ条件】-軸関係の退避を行う",
"圧力治具",
"①-1 ｢部品ﾃﾞｰﾀ｣⇒｢設備動作｣⇒｢仮圧ﾍｯﾄﾞﾞ動作｣ 仮圧着速度:20mm/s①-2 ｢ﾏｼﾝﾃﾞｰﾀ｣⇒｢〔M〕仮圧着｣⇒｢仮圧ﾍｯﾄﾞ｣ 仮圧着速度距離:0.5mm",
"検査表①:仮圧着部圧力測定",
"ｱﾝﾌﾟ設定方法",
"WWYJ-5500-002"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "正常な事",
"Method": "ﾛｰﾄﾞｾﾙｱﾝﾌﾟ",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着部圧力測定2",
"WorkItems": [
"9. 結果登録後､再度10､30､50､75､100Nを測定し事前ﾃﾞｰﾀへ記入する"
],
"WorkPoints": [
"規格:入力値±10%"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"6. ①【ﾍｯﾄﾞ原点位置移動】-②【隙間量移動】-③【はい】-④ﾛｰﾄﾞｾﾙをｾｯﾄ､⑤【微調整ﾎﾞﾀﾝで】⑥【ﾍｯﾄﾞ下降上昇】で5N出力する高さをﾃｨｰﾁ ⑦【結果登録】で治具厚み計測完了",
"7. 【ﾍｯﾄﾞ荷重】:10､30､50, 75 ,100Nの3条件を 設定し 【計測開始】",
"8. 前ﾍﾟｰｼﾞの測定ﾎﾟｲﾝﾄ計測後､【換算定数自動計算】を押し､ 表の値を入力し､【計算実行】を押す",
"検査表①:仮圧着部圧力測定",
"WWYJ-5500-002"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "入力値の±10%以下",
"Method": "目視",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "本圧圧力測定治具",
"Size": "",
"ToolOther": "FM-3796",
"WorkName": "本圧着部[P1][P2]圧力測定1",
"WorkItems": [
"1. ﾛｰﾄﾞｾﾙとｱﾝﾌﾟを接続しｱﾝﾌﾟの設定を行う(治具取付け)",
"3. 本圧ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞに治具をｾｯﾄする",
"4. ﾊﾟﾗﾒｰﾀ確認",
"2. 【ﾃﾞｰﾀ管理ﾒﾆｭｰ】-【ﾏｼﾝﾃﾞｰﾀ編集】-【ﾌﾟﾛｾｽﾃﾞｰﾀ荷重】-【ﾌﾟﾛｾｽ確認荷重】-【P1】/【P2】-【ﾕｰｻﾞｰ設定ﾌﾟﾛｾｽ条件】-軸関係の退避を行う"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5500-002",
"InspectionItems": [
"検査表①:本圧着部[P1]圧力測定"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"①ﾛｰﾄﾞｾﾙとｱﾝﾌﾟ接続②ﾒｼﾞｬｰSWに設定③ｾｯﾄﾎﾞﾀﾝを長押し､F-1を表示④再度､ｾｯﾄﾎﾞﾀﾝを長押し､ｾﾞﾛﾎﾞﾀﾝを押し､ 小数点が下3桁目にくるようにｾﾞﾛﾎﾞﾀﾝで設定 設定後､ｾｯﾄﾎﾞﾀﾝ長押し⑤ﾋﾟｰｸﾎｰﾙﾄﾞﾎﾞﾀﾝを押して F-3を表示させる⑥ｾｯﾄﾎﾞﾀﾝ長押し､ﾛｰﾄﾞｾﾙのひずみ値( mV/V) の数字をｾﾞﾛﾎﾞﾀﾝ･ﾋﾟｰｸﾎｰﾙﾄﾞﾎﾞﾀﾝで入力後､ｾｯﾄﾎﾞﾀﾝ長押し⑦ﾛｰﾄﾞｾﾙの定格荷重(N)を入力後､ｾｯﾄﾎﾞﾀﾝ長押し⑧荷重の小数点の位置をｾﾞﾛﾎﾞﾀﾝで設定後､ｾｯﾄﾎﾞﾀﾝ長押し⑨ｾﾞﾛﾎﾞﾀﾝを長押し､LEDを点灯させたら完了",
"圧力治具",
"ﾛｰﾄﾞｾﾙｱﾝﾌﾟ",
"500Nﾛｰﾄﾞｾﾙ",
"ﾋｰﾀ温度は制御停止で測定する事",
"ｱﾝﾌﾟ設定方法",
"5. 治具厚み計測を行う:【押込み量】:0.2mm､【荷重確認時間】:2s､【繰り返し回数】:3回､ 【待機荷重】:50N設定､【ﾍｯﾄﾞ荷重】:50N【治具厚み計測】を押す",
"①-1 ｢品種ﾃﾞｰﾀ｣⇒｢本圧着情報｣⇒｢本圧着条件｣ 本圧着速度:20mm/s①-2 ｢ﾏｼﾝﾃﾞｰﾀ｣⇒｢本圧着部[P1]/[P2]｣⇒｢本圧ﾍｯﾄﾞ｣ 本圧着速度距離:1.0mm",
"WWYJ-5500-002"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-3796",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "正常な事",
"Method": "本圧圧力測定治具",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾛｰﾄﾞｾﾙ",
"Size": "",
"ToolOther": "2kN",
"WorkName": "本圧着部[P1][P2]圧力測定1",
"WorkItems": [
"1. ﾛｰﾄﾞｾﾙとｱﾝﾌﾟを接続しｱﾝﾌﾟの設定を行う(治具取付け)",
"3. 本圧ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞに治具をｾｯﾄする",
"4. ﾊﾟﾗﾒｰﾀ確認",
"2. 【ﾃﾞｰﾀ管理ﾒﾆｭｰ】-【ﾏｼﾝﾃﾞｰﾀ編集】-【ﾌﾟﾛｾｽﾃﾞｰﾀ荷重】-【ﾌﾟﾛｾｽ確認荷重】-【P1】/【P2】-【ﾕｰｻﾞｰ設定ﾌﾟﾛｾｽ条件】-軸関係の退避を行う"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"①ﾛｰﾄﾞｾﾙとｱﾝﾌﾟ接続②ﾒｼﾞｬｰSWに設定③ｾｯﾄﾎﾞﾀﾝを長押し､F-1を表示④再度､ｾｯﾄﾎﾞﾀﾝを長押し､ｾﾞﾛﾎﾞﾀﾝを押し､ 小数点が下3桁目にくるようにｾﾞﾛﾎﾞﾀﾝで設定 設定後､ｾｯﾄﾎﾞﾀﾝ長押し⑤ﾋﾟｰｸﾎｰﾙﾄﾞﾎﾞﾀﾝを押して F-3を表示させる⑥ｾｯﾄﾎﾞﾀﾝ長押し､ﾛｰﾄﾞｾﾙのひずみ値( mV/V) の数字をｾﾞﾛﾎﾞﾀﾝ･ﾋﾟｰｸﾎｰﾙﾄﾞﾎﾞﾀﾝで入力後､ｾｯﾄﾎﾞﾀﾝ長押し⑦ﾛｰﾄﾞｾﾙの定格荷重(N)を入力後､ｾｯﾄﾎﾞﾀﾝ長押し⑧荷重の小数点の位置をｾﾞﾛﾎﾞﾀﾝで設定後､ｾｯﾄﾎﾞﾀﾝ長押し⑨ｾﾞﾛﾎﾞﾀﾝを長押し､LEDを点灯させたら完了",
"圧力治具",
"ﾛｰﾄﾞｾﾙｱﾝﾌﾟ",
"500Nﾛｰﾄﾞｾﾙ",
"ﾋｰﾀ温度は制御停止で測定する事",
"ｱﾝﾌﾟ設定方法",
"5. 治具厚み計測を行う:【押込み量】:0.2mm､【荷重確認時間】:2s､【繰り返し回数】:3回､ 【待機荷重】:50N設定､【ﾍｯﾄﾞ荷重】:50N【治具厚み計測】を押す",
"①-1 ｢品種ﾃﾞｰﾀ｣⇒｢本圧着情報｣⇒｢本圧着条件｣ 本圧着速度:20mm/s①-2 ｢ﾏｼﾝﾃﾞｰﾀ｣⇒｢本圧着部[P1]/[P2]｣⇒｢本圧ﾍｯﾄﾞ｣ 本圧着速度距離:1.0mm",
"検査表①:本圧着部[P1]圧力測定",
"WWYJ-5500-002"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "正常な事",
"Method": "ﾛｰﾄﾞｾﾙ",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾛｰﾄﾞｾﾙｱﾝﾌﾟ",
"Size": "",
"ToolOther": "",
"WorkName": "本圧着部[P1][P2]圧力測定1",
"WorkItems": [
"1. ﾛｰﾄﾞｾﾙとｱﾝﾌﾟを接続しｱﾝﾌﾟの設定を行う(治具取付け)",
"3. 本圧ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞに治具をｾｯﾄする",
"4. ﾊﾟﾗﾒｰﾀ確認",
"2. 【ﾃﾞｰﾀ管理ﾒﾆｭｰ】-【ﾏｼﾝﾃﾞｰﾀ編集】-【ﾌﾟﾛｾｽﾃﾞｰﾀ荷重】-【ﾌﾟﾛｾｽ確認荷重】-【P1】/【P2】-【ﾕｰｻﾞｰ設定ﾌﾟﾛｾｽ条件】-軸関係の退避を行う"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"①ﾛｰﾄﾞｾﾙとｱﾝﾌﾟ接続②ﾒｼﾞｬｰSWに設定③ｾｯﾄﾎﾞﾀﾝを長押し､F-1を表示④再度､ｾｯﾄﾎﾞﾀﾝを長押し､ｾﾞﾛﾎﾞﾀﾝを押し､ 小数点が下3桁目にくるようにｾﾞﾛﾎﾞﾀﾝで設定 設定後､ｾｯﾄﾎﾞﾀﾝ長押し⑤ﾋﾟｰｸﾎｰﾙﾄﾞﾎﾞﾀﾝを押して F-3を表示させる⑥ｾｯﾄﾎﾞﾀﾝ長押し､ﾛｰﾄﾞｾﾙのひずみ値( mV/V) の数字をｾﾞﾛﾎﾞﾀﾝ･ﾋﾟｰｸﾎｰﾙﾄﾞﾎﾞﾀﾝで入力後､ｾｯﾄﾎﾞﾀﾝ長押し⑦ﾛｰﾄﾞｾﾙの定格荷重(N)を入力後､ｾｯﾄﾎﾞﾀﾝ長押し⑧荷重の小数点の位置をｾﾞﾛﾎﾞﾀﾝで設定後､ｾｯﾄﾎﾞﾀﾝ長押し⑨ｾﾞﾛﾎﾞﾀﾝを長押し､LEDを点灯させたら完了",
"圧力治具",
"ﾛｰﾄﾞｾﾙｱﾝﾌﾟ",
"500Nﾛｰﾄﾞｾﾙ",
"ﾋｰﾀ温度は制御停止で測定する事",
"ｱﾝﾌﾟ設定方法",
"5. 治具厚み計測を行う:【押込み量】:0.2mm､【荷重確認時間】:2s､【繰り返し回数】:3回､ 【待機荷重】:50N設定､【ﾍｯﾄﾞ荷重】:50N【治具厚み計測】を押す",
"①-1 ｢品種ﾃﾞｰﾀ｣⇒｢本圧着情報｣⇒｢本圧着条件｣ 本圧着速度:20mm/s①-2 ｢ﾏｼﾝﾃﾞｰﾀ｣⇒｢本圧着部[P1]/[P2]｣⇒｢本圧ﾍｯﾄﾞ｣ 本圧着速度距離:1.0mm",
"検査表①:本圧着部[P1]圧力測定",
"WWYJ-5500-002"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "正常な事",
"Method": "ﾛｰﾄﾞｾﾙｱﾝﾌﾟ",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "本圧着部[P1][P2]圧力測定2",
"WorkItems": [],
"WorkPoints": [
"規格:入力値が100N未満は±10N､100N以上は±10%"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"6. ①【ﾍｯﾄﾞ原点位置移動】-②【隙間量移動】-③【はい】-④ﾛｰﾄﾞｾﾙをｾｯﾄ､ ⑤【微調整ﾎﾞﾀﾝで】⑥【ﾍｯﾄﾞ下降上昇】で5N出力する高さをﾃｨｰﾁ⑦【結果登録】で治具厚み計測完了",
"7. 【ﾍｯﾄﾞ荷重】:30､500､1000Nの 3条件を設定し【計測開始】",
"8. 前ﾍﾟｰｼﾞの測定ﾎﾟｲﾝﾄ計測後､【換算定数自動計算】を押し､ 表の値を入力し､【計算実行】を押す",
"9. 結果登録後､再度30､500､1000Nを測定し事前ﾃﾞｰﾀへ記入する",
"検査表①:本圧着部[P1]圧力測定",
"WWYJ-5500-002"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "入力値の±10Nもしくは±10%の大きい方",
"Method": "目視",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇温確認",
"WorkItems": [
"1. TEGﾌﾟﾛｸﾞﾗﾑを選択",
"2. ﾌﾟﾛｸﾞﾗﾑ内のﾃﾞｰﾀ確認(上記ﾃﾞｰﾀ選択後)",
"3. 各ﾋｰﾀの昇温確認",
"4. 各工程の昇温確認ができれば完了"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"温度の上昇を確認",
"①【品種情報表示】を押す",
"③ACF貼付け情報画面(条件)",
"④仮圧着情報画面(条件)･･･部品ﾃﾞｰﾀ内に有り",
"①ﾒｲﾝ画面【ﾒﾝﾃﾅﾝｽﾒﾆｭｰ】",
"⑤本圧着情報画面(条件)",
"③【貼付/仮圧着温度】･･･選択し制御開始を押す",
"②各工程条件確認",
"④【本圧着温度/ﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞ】･･･選択し制御開始を押す",
"※ﾌﾟﾛｸﾞﾗﾑ名:17-IC-ACC-P1P2(本圧ﾍｯﾄﾞ本数)",
"※ﾌﾟﾛｸﾞﾗﾑ名:17-TCP-ACC-P1P2(本圧ﾍｯﾄﾞ本数)",
"検査表①:昇温確認",
"IC仕様",
"TCP仕様",
"②【ﾌﾟﾛｾｽﾁｪｯｸ】",
"WWYJ-5500-002"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "昇温する事",
"Method": "目視",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "感圧紙",
"Size": "",
"ToolOther": "",
"WorkName": "最終平面確認",
"WorkItems": [
"1. 平面測定方法①【ﾌﾟﾛｾｽ確認ﾒﾆｭｰ】-②【平行度確認】-③【【各工程を選択し下記条件を確認する】】-④【ﾍｯﾄﾞ選択】-⑤【計測開始】",
"3. 計測開始【規格:全面均一発色】",
"4. 調整方法･･･感圧紙の状態を確認し褐色状態が悪い(平面が出ていない)場合は下記を参照の上､調整を行う",
"2. 各工程条件"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"③荷重:130N 時間:0.1s",
"④ﾍｯﾄﾞ選択",
"⑤計測開始",
"①ﾌﾟﾛｾｽ確認ﾒﾆｭｰ",
"②平行度確認",
"感圧紙=3L",
"感圧紙=3L",
"感圧紙=2L保護ｼｰﾄ:ｶﾌﾟﾄﾝｼｰﾄ(t80μm)",
"調整ﾎﾞﾙﾄ×4箇所",
"調整ﾎﾞﾙﾄ固定用ｾｯﾄﾋﾞｽを緩める事",
"調整ﾎﾞﾙﾄ×4箇所",
"検査表①:最終平面確認",
"調整ﾎﾞﾙﾄ固定用ｾｯﾄﾋﾞｽを緩める事",
"調整ﾎﾞﾙﾄ×2箇所",
"IC仕様",
"TCP仕様",
"ACF貼付け",
"仮圧",
"本圧",
"ACF貼付け ≪ﾍｯﾄﾞ先端部≫",
"仮圧 ≪ﾍｯﾄﾞ先端部≫",
"本圧 ≪ﾍｯﾄﾞくさび≫",
"WWYJ-5500-002"
]
} | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "全面均一発色",
"Method": "目視",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ACF終端検出ｾﾝｻ調整",
"WorkItems": [
"1. ACF終端検出ｾﾝｻｰ設定方法",
"2. ACF終端検出ｾﾝｻｰ調整方法"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:ACF終端検出ｾﾝｻ調整",
"WWYJ-5500-002"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定されている事",
"Method": "目視",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "工具顕微鏡",
"Size": "",
"ToolOther": "",
"WorkName": "ｶｯﾀ切込量調整",
"WorkItems": [
"1. 操作方法",
"2. 切込み調整",
"3. 工具顕微鏡で確認する"
],
"WorkPoints": [
"切込量確認:ﾍﾞｰｽﾃｰﾌﾟ厚み1/3の切込"
],
"Tolks": [],
"InspectionNo": "WWYJ-5500-002",
"InspectionItems": [
"検査表①:ｶｯﾀ切込量調整"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ACFが切れない方向",
"ACFが切れる方向",
"調整方法",
"①【ACF操作】を押す",
"②【ﾍｯﾄﾞ選択】-③【ACFﾌｨｰﾄﾞ量】 -④【捨打ち】-⑤【ACF初期化】",
"WWYJ-5500-002"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "ﾍﾞｰｽﾃｰﾌﾟ厚み1/3の切込",
"Method": "工具顕微鏡",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "工具顕微鏡",
"Size": "",
"ToolOther": "",
"WorkName": "踏残し量確認",
"WorkItems": [
"1. 操作方法",
"2. 踏残し量を工具顕微鏡で確認",
"3. 調整方法"
],
"WorkPoints": [
"踏残し量:0.3~0.5mm",
"10.85mmより数値を下げた場合 ⇒ACF踏残量は増える10.85mmより数値を上げた場合 ⇒ACF踏残量は減る"
],
"Tolks": [],
"InspectionNo": "WWYJ-5500-002",
"InspectionItems": [
"検査表①:踏残し量確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ACF操作で捨打ちﾌﾟﾚｰﾄへACFを貼付ける",
"ｶｯﾀｰ端面",
"ﾍｯﾄﾞﾂｰﾙ端面",
"10.85mm",
"①【ACF操作】を押す",
"※上記踏残量になるように調整を行う",
"①【ﾃﾞｰﾀ管理ﾒﾆｭｰ】を押す",
"②【ﾏｼﾝﾃﾞｰﾀ編集】を押す",
"③【[A]ACF貼付部】を選択し【貼付ﾍｯﾄﾞ】のL/Rを選択",
"④下図:ACFｶｯﾀｰ基準位置L/Rの設定10.850mmの数値変更で踏残量を調整する",
"WWYJ-5500-002"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "踏残し量0.3~0.5㎜",
"Method": "工具顕微鏡",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "工具顕微鏡",
"Size": "",
"ToolOther": "",
"WorkName": "ACF貼付け精度",
"WorkItems": [
"1. ACF実装前設定",
"3. ACF実装確認",
"2. 設備をｽﾀｰﾄしﾊﾟﾈﾙ投入のﾒｯｾｰｼﾞ に従い､ﾊﾟﾈﾙを投入する"
],
"WorkPoints": [
"ACF貼付け精度:X=±0.2mm/3σ Y=±0.1mm/3σ",
"※再調整が完了したら再度1)から作業をやり直しACF精度測定を実施する"
],
"Tolks": [],
"InspectionNo": "WWYJ-5500-002",
"InspectionItems": [
"検査表①:ACF貼付け精度"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"下限ｾﾝｻONの事",
"X方向NG",
"精度NGの場合",
"①ﾍｯﾄﾞとﾊﾞｯｸｱｯﾌﾟｽﾃｰｼﾞの間にﾊﾟﾈﾙを挟み込む",
"条件は手投入で手取出しﾓｰﾄﾞ(ACF貼付けのみ)",
"②この時上図のように下限ｾﾝｻｰがONするように調整",
"貼付条件(IC仕様) ･貼付長さ: 28.6mm(1ヶ所) 短辺側のみ ･温度: 120℃設定 ･荷重: 70N ･時間: 0.5s",
"貼付条件(TCP仕様) ･貼付長さ: 42mm(1ヶ所) 短辺側のみ ･温度: 120℃設定 ･荷重: 60N ･時間: 0.5s",
"①【生産ﾓｰﾄﾞ設定】を押す",
"②【貼付項目】のみﾁｪｯｸする",
"①実際に実装したﾊﾟﾈﾙを顕微鏡にて測定",
"②貼付け位置変更がなければ事前ﾃﾞｰﾀに従い､指定の枚数のACF実装精度を測定する",
"※ﾊﾟﾈﾙ､ACF､ICに起因する(誤差要因は含まない)",
"Y方向NG",
"ACFｶﾞｲﾄﾞﾛｰﾗの幅を再調整する",
"WWYJ-5500-002"
]
} | {
"QualityItem": "精度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "X±0.2㎜/3σY±0.1㎜/3σ",
"Method": "工具顕微鏡",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TCP操作盤説明",
"WorkItems": [
"1. TCP供給部操作盤の説明は下記に記載"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"①OPERATION ENABLED 供給部操作盤有効SW②BUSY 点灯時､動作中③PART FEED〈FWD〉 1部品分正回転送り⑤PITCH FEED〈FWD〉 ﾊﾟｰﾌｫﾚｰｼｮﾝ1個分正回転送り⑥PITCH FEED〈REV〉 ﾊﾟｰﾌｫﾚｰｼｮﾝ1個分逆回転送り⑦SHORT FEED〈FWD〉 微小正回転送り⑧SHORT FEED〈REV〉 微小逆回転送り⑨POWER RESTORATION ｻｰﾎﾞONSW",
"⑩ERR RESET ｴﾗｰ解除SW⑪REEL〈UNREEL〉 供給側段差ﾛｰﾗ巻取り⑫REEL〈WIND〉 巻取側段差ﾛｰﾗ巻取り⑬TAPE HEAD SEARCH TCP頭出しSW⑭SCAN FEED TCPを打ち抜き位置まで送る⑮PUNCH CHECK 打ち抜き動作⑯TAPE PUSHER〈LOW〉 ﾃｰﾌﾟ下降高さへ移動⑰MOLD〈VAC/BLOW〉 金型吸着ON⇔OFF",
"WWYJ-5500-002"
]
} | {
"QualityItem": "操作確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "正常な事",
"Method": "目視",
"RecordMethod": "WWYJ-5500-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TCP引き回し事前準備",
"WorkItems": [
"1. 以下のTEG用ﾜｰｸを用意する",
"2. 下記のようにTEG用ﾜｰｸをｾｯﾄする"
],
"WorkPoints": [
"A断面 詳細"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"①ｽﾄｯﾊﾟｰ×3個",
"②巻き取りﾘｰﾙ×1個",
"③ｽﾍﾟｰｻ×2個",
"④金型×1個",
"⑤TCPﾘｰﾙ×2個",
"①③⑤",
"①③⑤",
"TCP供給部",
"③ｽﾍﾟｰｻ",
"⑤TCPﾘｰﾙ",
"①ｽﾄｯﾊﾟｰ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "TCP引き回し",
"WorkItems": [
"1. OPERATION ENABLEDを押し操作盤を有効にする",
"2. TCPを下記のように引き回す"
],
"WorkPoints": [
"赤線:TCPの引き回し経路",
"青丸部金型周辺の詳細",
"操作盤の③④⑤⑥にて操作",
"操作盤⑪⑫にて巻き取り動作を行う",
"操作盤の⑦⑧にて微小送り ⑯にてﾃｰﾌﾟ下降させ目視確認を行う",
"青線:保護ﾃｰﾌﾟの引き回し経路",
"ｽﾞﾚている場合操は作盤の③④⑤⑥にて位置を合わす｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"供給側段差ﾛｰﾗ",
"巻取側段差ﾛｰﾗ",
"TCP",
"金型",
"4. 打ち抜く部品と金型の打ち抜き位置を大体合わせる",
"5. 微小送りで金型下ﾋﾟﾝにﾊﾟｰﾌｫﾚｰｼｮﾝが合うようにする",
"3. 黄丸の段差ﾛｰﾗ部にて下限のｾﾝｻを切らないようにする",
"6. 調整後目視にてTCPの打ち抜き位置を確認",
"ﾃｰﾌﾟ下降時ﾋﾟﾝが挿入していること"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.