input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉大)組立⑦",
"WorkItems": [
"1. ①にPULL を取付"
],
"WorkPoints": [
"IC供給有りの場合実施する",
"取付方向注意",
"外側面から挿入し､ﾜﾝﾀｯﾁ留め具を押し込み固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"外側面",
"押し込む方向",
"内側面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉大)組立⑧",
"WorkItems": [
"1. ①にHINGE をBOLT ･WASHER で取付"
],
"WorkPoints": [
"IC供給有りの場合実施する",
"取付方向注意",
"取付方向注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"×3",
"外側面",
"×3",
"×3",
"×3"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立①",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ",
"中央ﾌﾚｰﾑ固定用の穴が扉下側になるよう組付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M6",
"M5",
"M4",
"M3",
"ﾅｯﾄ挿入面",
"×2",
"扉上側",
"×2",
"A矢視図"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立②",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ",
"中央ﾌﾚｰﾑ固定用の穴が扉下側になるよう組付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M6",
"M5",
"M4",
"M3",
"ﾅｯﾄ挿入面A",
"×3",
"扉上側",
"×3",
"ﾅｯﾄ挿入面B",
"扉上側",
"×4",
"×4"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立③",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT ･NUT ･CAP を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ",
"ﾀｯﾌﾟ穴が扉左側になるよう組付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×4",
"ﾅｯﾄ挿入面A",
"扉右側",
"M6",
"M5",
"M4",
"M3",
"裏面図",
"ﾅｯﾄ挿入面B",
"×2"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立③",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT ･NUT ･CAP を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ",
"ﾀｯﾌﾟ穴が扉左側になるよう組付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×4",
"ﾅｯﾄ挿入面A",
"扉右側",
"M6",
"M5",
"M4",
"M3",
"裏面図",
"ﾅｯﾄ挿入面B",
"×2"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立④",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT ･CABLE-SUPPORT ･NUT ･NUT を取付"
],
"WorkPoints": [
"ﾌﾗｯﾄ面",
"風船色ﾅｯﾄｻｲｽﾞ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"ﾅｯﾄ挿入面C",
"扉上側",
"M6",
"M5",
"M4",
"M3",
"×4",
"×3",
"ﾅｯﾄ挿入面A",
"ﾅｯﾄ挿入面B",
"×4",
"×3",
"×4",
"×4"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑤",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT ･CAP ･NUT ･NUT を取付"
],
"WorkPoints": [
"ﾌﾗｯﾄ面",
"風船色ﾅｯﾄｻｲｽﾞ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"ﾅｯﾄ挿入面C",
"扉上側",
"M6",
"M5",
"M4",
"M3",
"×2",
"ﾅｯﾄ挿入面A",
"ﾅｯﾄ挿入面B",
"×2",
"×4",
"×4"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑥",
"WorkItems": [
"1. CLAMP を指定の長さにｶｯﾄ",
"1. 1.完成品･②･③･④･⑤･FRAME ･PANEL ･PANEL をBOLT で組付け"
],
"WorkPoints": [
"ｶｯﾄした両端を､更に図のようにｶｯﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"外側面",
"L=287.5",
"L=430"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑦",
"WorkItems": [
"1. ①に②をBRACKET ･WASHER ･BOLT で組付け"
],
"WorkPoints": [
"取っ手取付用穴",
"A矢視図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"外側面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑧",
"WorkItems": [
"1. ①にHINGE をSCREW で取付"
],
"WorkPoints": [
"取っ手取付用穴",
"白ﾌﾟﾗｽﾁｯｸが下になる様に取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"外側面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑨",
"WorkItems": [
"2. BRACKET にSWITCH をNUT-PLATE ･BOLT ･WASHER ･WASHER で取付",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "WWYJ-5300-033",
"InspectionItems": [
"検査表①:安全部品確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"9月",
"WWYJ-5300-033"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-033",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑨",
"WorkItems": [
"2. BRACKET にSWITCH をNUT-PLATE ･BOLT ･WASHER ･WASHER で取付",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"9月",
"検査表①:安全部品確認",
"WWYJ-5300-033"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-033",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾍｷｻﾛT20",
"ToolOther": "1.0N･m",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑨",
"WorkItems": [
"2. BRACKET にSWITCH をNUT-PLATE ･BOLT ･WASHER ･WASHER で取付",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"9月",
"検査表①:安全部品確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑩",
"WorkItems": [
"1. ①に②をBOLT ･WASHER で取付"
],
"WorkPoints": [
"取っ手取付用穴"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"×2",
"内側面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑪",
"WorkItems": [
"1. ①にCATCH をBOLT で取付"
],
"WorkPoints": [
"取っ手取付用穴"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"×2",
"内側面",
"×2"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑫",
"WorkItems": [
"1. ①にBRACKET ･PLATE をBOLT ･WASHER ･BOLT で取付"
],
"WorkPoints": [
"ﾌﾚｰﾑ下面に直角平行に取付",
"取っ手取付用穴",
"ﾌﾚｰﾑに対して直角平行に取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"内側面",
"A矢視図"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑬",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "非常停止ｽｲｯﾁ組立",
"WorkItems": [
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入",
"3. 1.完成品にSWITCH を取付",
"2. BOX にLABEL を貼付け"
],
"WorkPoints": [
"型式確認･ｼﾘｱﾙNo記録",
"穴ｾﾝﾀｰに貼付"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-033",
"InspectionItems": [
"検査表①:安全部品確認"
],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"1.完成品",
"WWYJ-5300-033"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-033",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "非常停止ｽｲｯﾁ組立",
"WorkItems": [
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入",
"3. 1.完成品にSWITCH を取付",
"2. BOX にLABEL を貼付け"
],
"WorkPoints": [
"型式確認･ｼﾘｱﾙNo記録",
"穴ｾﾝﾀｰに貼付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"1.完成品",
"検査表①:安全部品確認",
"WWYJ-5300-033"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-033",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾅｯﾄ締付治具",
"Size": "",
"ToolOther": "FM-2528",
"WorkName": "非常停止ｽｲｯﾁ組立",
"WorkItems": [
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入",
"3. 1.完成品にSWITCH を取付",
"2. BOX にLABEL を貼付け"
],
"WorkPoints": [
"型式確認･ｼﾘｱﾙNo記録",
"穴ｾﾝﾀｰに貼付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"1.完成品",
"検査表①:安全部品確認",
"■安全作業"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2528",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "操作ﾊﾟﾈﾙ組立",
"WorkItems": [
"2. COVER にSWITCH ･SWITCH ･SWITCH ･SWITCH を取付",
"3. 1.完成品に①をWASHER ･BOLT で取付",
"■1. SWITCH ･SWITCH ･SWITCH ･SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入"
],
"WorkPoints": [
"①は裏面からWASHER ･BOLT で取付",
"型式確認･ｼﾘｱﾙNo記録",
"SWITCH ~SWITCH 部品の切り欠きをCOVER の溝にはめ込み取付"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-124",
"InspectionItems": [
"検査表①:型式･ｼﾘｱﾙ･検査書ﾁｪｯｸ"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"1.完成品",
"1.完成品",
"WWYJ-5300-124"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-124",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "操作ﾊﾟﾈﾙ組立",
"WorkItems": [
"2. COVER にSWITCH ･SWITCH ･SWITCH ･SWITCH を取付",
"3. 1.完成品に①をWASHER ･BOLT で取付",
"■1. SWITCH ･SWITCH ･SWITCH ･SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入"
],
"WorkPoints": [
"①は裏面からWASHER ･BOLT で取付",
"型式確認･ｼﾘｱﾙNo記録",
"SWITCH ~SWITCH 部品の切り欠きをCOVER の溝にはめ込み取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"1.完成品",
"1.完成品",
"検査表①:型式･ｼﾘｱﾙ･検査書ﾁｪｯｸ",
"WWYJ-5300-124"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-124",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "操作ﾊﾟﾈﾙ配線",
"WorkItems": [
"1. ①にCABLE を取付"
],
"WorkPoints": [
"①は裏面から⑳・㉑で取付"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-124",
"InspectionItems": [
"検査表①:接続確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"S10821R",
"S10822R",
"S10823R",
"S10826R",
"S10825R",
"1S10821R",
"WWYJ-5300-124"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-124",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け",
"WorkItems": [
"2.①にLABEL ･LABEL を貼付",
"■1.LABEL の型式確認"
],
"WorkPoints": [
"貼付位置:±2mm以下",
"型式確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"75㎜",
"30㎜",
"85㎜",
"5㎜",
"270㎜",
"15㎜",
"50㎜",
"検査表①:ﾌﾛﾝﾄｶﾊﾞｰ 右【貼付位置確認】",
"検査表①:ﾌﾛﾝﾄｶﾊﾞｰ 右【安全部品確認】",
"WWYJ-5300-124"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-124",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け",
"WorkItems": [
"2.①にLABEL ･LABEL を貼付",
"■1.LABEL の型式確認"
],
"WorkPoints": [
"貼付位置:±2mm以下",
"型式確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"75㎜",
"30㎜",
"85㎜",
"5㎜",
"270㎜",
"15㎜",
"50㎜",
"検査表①:ﾌﾛﾝﾄｶﾊﾞｰ 右【貼付位置確認】",
"検査表①:ﾌﾛﾝﾄｶﾊﾞｰ 右【安全部品確認】"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾀｯﾁﾊﾟﾈﾙﾌﾚｰﾑ組立",
"WorkItems": [
"1. GROMMET を下図の様にｶｯﾄする",
"2. COVER に1.完成品･GROMMET を取付",
"3. 2.完成品にCABLE-SUPPORT を取付",
"4. 3.完成品にRUBBER-LEG をBOLT で取付"
],
"WorkPoints": [
"ｶｯﾄするのは1個のみ",
"ｶｯﾄ無",
"ｶｯﾄ有"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"1.完成品"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉FRONT-RIGHT)組立⑭",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立①",
"WorkItems": [
"1. FRAME にSUPPORT NUT NUT を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ",
"中央ﾌﾚｰﾑ固定用の穴が扉下側になるよう組付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M6",
"M5",
"M4",
"M3",
"×2",
"ﾅｯﾄ挿入面",
"扉上側",
"×2",
"A矢視図"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立②",
"WorkItems": [
"1. FRAME にSUPPORT NUT CAP を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ",
"ﾀｯﾌﾟ穴が扉左側になるよう組付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×2",
"ﾅｯﾄ挿入面",
"扉左側",
"M6",
"M5",
"M4",
"M3",
"裏面図"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立③",
"WorkItems": [
"1. FRAME にSUPPORT NUT を取付"
],
"WorkPoints": [
"ﾌﾗｯﾄ面",
"風船色ﾅｯﾄｻｲｽﾞ",
"中央ﾌﾚｰﾑ固定用の穴が扉下側になるよう組付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾅｯﾄ挿入面",
"扉上側",
"M6",
"M5",
"M4",
"M3",
"×2",
"×2"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立④",
"WorkItems": [
"1. FRAME にCAP を取付"
],
"WorkPoints": [
"風船色ﾅｯﾄｻｲｽﾞ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"扉左側",
"M6",
"M5",
"M4",
"M3"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑤",
"WorkItems": [
"1. CLAMP を指定の長さにｶｯﾄ",
"2. 1.完成品･②③④⑤FRAME PANEL PANEL をBOLT で組付け"
],
"WorkPoints": [
"ｶｯﾄした両端を､更に図のようにｶｯﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"L=825",
"L=430"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑥",
"WorkItems": [
"1. ①にHINGE をSCREW で取付"
],
"WorkPoints": [
"取っ手取付用穴",
"白ﾌﾟﾗｽﾁｯｸが下になる様に取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"外側面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑦",
"WorkItems": [
"2. BRACKET にSWITCH をNUT-PLATE BOLT WASHER WASHER で取付",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:安全部品確認"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑦",
"WorkItems": [
"2. BRACKET にSWITCH をNUT-PLATE BOLT WASHER WASHER で取付",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "WWYJ-5300-035",
"InspectionItems": [
"検査表①:安全部品確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"WWYJ-5300-035"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-035",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾍｷｻﾛT20",
"ToolOther": "1.0N･m",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑦",
"WorkItems": [
"2. BRACKET にSWITCH をNUT-PLATE BOLT WASHER WASHER で取付",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:安全部品確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑧",
"WorkItems": [
"1. ①に②をBOLT ･WASHER で取付"
],
"WorkPoints": [
"取っ手取付用穴"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"×2",
"内側面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑨",
"WorkItems": [
"1. ①にCATCH をBOLT で取付",
"2. ①にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"取っ手取付用穴"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"×2",
"内側面",
"×2"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(扉)組立⑩",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "a,b,c部配管接続",
"WorkItems": [
"1. 後部ﾕﾆｯﾄ配管を接続する"
],
"WorkPoints": [
"※(ﾌﾚｰﾑより)とある配管は圧力制御用ｴｱｰでﾌﾚｰﾑに配管されている",
"供給部の選択により接続がある場合はｼﾞｮｲﾝﾄにあるﾌﾟﾗｸﾞを取り外し接続します(廃棄)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"b部",
"a部",
"φ6白 V001",
"仮圧着",
"移載",
"c部",
"b部",
"a部",
"ACF",
"P002",
"P003",
"c部",
"ﾄﾚｲｽﾄｯｶｰ(IC供給有り)",
"P022",
"φ6黒 P022",
"P004",
"φ6黒 P004",
"V002",
"V001",
"φ6白 V002",
"φ6橙 E021",
"E021",
"E002",
"E001",
"φ6橙 E001",
"φ6橙 E002",
"φ8黒 P002",
"φ8黒 P003(ﾌﾚｰﾑより)",
"φ8黒 P001",
"P001",
"φ6白 V021",
"φ8黒 P021",
"P021",
"V021",
"ﾄﾚｲｽﾃｰｼﾞ(IC供給有り)",
"φ6白 V011",
"φ6白 V012",
"V011",
"V012",
"φ6黒 P011",
"φ6黒 P012(ﾌﾚｰﾑより)",
"φ6黒 P013",
"P012",
"P013",
"P011",
"E012",
"E011",
"φ6橙 E011",
"φ6橙 E012",
"P016",
"P015",
"P014",
"φ6黒 P014",
"φ6黒 P015",
"φ4黒 P016",
"φ6白 V022",
"V022"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "f部配管接続",
"WorkItems": [
"1. 上流仮置き配管を接続する"
],
"WorkPoints": [
"ｵﾌﾟｼｮﾝ追加により接続がある場合はｼﾞｮｲﾝﾄにあるﾌﾟﾗｸﾞを取り外し接続します(廃棄)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"f部",
"前側",
"φ6白 V061",
"φ6黒 P061",
"P061",
"φ6橙 E063(OP)",
"V061",
"P067",
"φ6黒 P062",
"後側",
"φ6黒 P064",
"E061",
"φ6黒 P066",
"上流仮置ﾕﾆｯﾄ",
"φ6黒 P063",
"φ4黒 P065",
"ｲｵﾅｲｻﾞｰ",
"P062",
"P063",
"P065",
"上流仮置ﾕﾆｯﾄ",
"ｲｵﾅｲｻﾞｰ",
"IC供給ｶﾊﾞｰﾛｯｸ(OP)",
"本体ｶﾊﾞｰﾛｯｸ",
"φ6黒 P067",
"φ6橙 E061",
"φ6橙 E062",
"E063",
"E062",
"P064",
"P066"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "e,d部配管接続",
"WorkItems": [
"1. 前部ﾕﾆｯﾄ配管を接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"e部",
"ﾃｰﾌﾞﾙ(A1)",
"ﾃｰﾌﾞﾙ(A2)",
"d部",
"e部",
"d部",
"φ4黒 P045",
"φ6白 V051",
"φ6黒 P051",
"φ6黒 P052",
"P046",
"E051",
"P052",
"搬送ｱｰﾑ1",
"φ6白 V041",
"V051",
"φ6橙 E051",
"P051",
"φ4黒 P041",
"φ4黒 P042",
"V043",
"φ6白 V043",
"P045",
"φ4黒 P046",
"V041",
"P042",
"P041"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "i,h部配管接続",
"WorkItems": [
"1. 前部ﾕﾆｯﾄ配管を接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"i部",
"ﾃｰﾌﾞﾙ(M1)",
"j部",
"i部",
"h部",
"φ4黒 P081",
"E091",
"搬送ｱｰﾑ2",
"φ6白 V091",
"φ6橙 E091",
"P092",
"φ6黒 P091",
"φ6黒 P092",
"φ6白 V082",
"φ4黒 P082",
"P091",
"ﾃｰﾌﾞﾙ(M2)",
"V081",
"V082",
"P082",
"P081",
"φ6白 V081",
"φ4黒 P085",
"V091",
"φ4黒 P086",
"φ6橙 E081",
"φ6橙 E082",
"E082",
"E081",
"P086",
"P085"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾏｸﾞﾈｯﾄ取付け",
"WorkItems": [
"1. ﾊｰﾈｽﾎﾞｰﾄﾞにﾏｸﾞﾈｯﾄを取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"⇒ﾏｸﾞﾈｯﾄ中",
"⇒ﾏｸﾞﾈｯﾄ大"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊｰﾈｽ準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.下記ﾘｽﾄの順番でｹｰﾌﾞﾙを準備する"
]
} | {
"QualityItem": "ｹｰﾌﾞﾙの準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "付属品準備",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.下記ﾘｽﾄで付属品を準備する"
]
} | {
"QualityItem": "ｹｰﾌﾞﾙの準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"D-X2102",
"CN5K3012",
"CN1K3007",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN15K009/CN5K009",
"ICTR11P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回3",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN13K009",
"ICTR10P",
"CN16K010",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回4",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN3K3100",
"ACF7R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回5",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN3K3101/CN4K3101",
"MMU7R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回6",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN11K009P",
"CN11K009",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回7",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1TB1K012/2TB1K012",
"ACF15R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回8",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"3TB1K012/4TB1K012",
"ACF16R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回9",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CH1A002",
"ACF5R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回10",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CH2A002",
"ACF6R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回11",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN9K005",
"R30525R",
"R30526R",
"R30527R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回12",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"D-X2102",
"CN1K3009",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回13",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN10K007",
"CX2112",
"1G10740R",
"1G10730R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回14",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"MMU8R",
"ICTR12P",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回15",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"F-X2101",
"CN2K3100",
"CN1K3101",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回16",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"C-X2102",
"CN1K3132",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回17",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"CN4K3100",
"ICTR3R",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ﾊｰﾈｽ引き回18",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B-X2101",
"CN1K3131",
"1. CABLE を引き回す"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り準備する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊｰﾈｽﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-6412",
"WorkName": "ｲﾝｼｭﾛｯｸ固定",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. ｲﾝｼｭﾛｯｸで固定する",
"⇒100mm",
"⇒150mm",
"⇒200mm",
"⇒250mm"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6412",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "架台上面中継JOINT組付け①",
"WorkItems": [
"1. PLATE にJOINT を取付",
"2. PLATE にJOINT GROMMET を取付",
"3. PLATE にJOINT GROMMET を取付"
],
"WorkPoints": [
"3個製作(g:j:l用)",
"1個製作(n用)",
"1個製作(m用)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"上面",
"下面",
"上面",
"下面",
"上面",
"下面",
"上面",
"上面",
"上面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "架台上面中継JOINT組付け②(g部)",
"WorkItems": [
"1. ①にJOINT ･JOINT を取付",
"2. 1.完成品にJOINT ･JOINT ･JOINT を取付",
"3. 2.完成品にﾏｽｷﾝｸﾞﾃｰﾌﾟでﾎﾟｼﾞｼｮﾝ名称を記入",
"4. 3.完成品にBOLT ･WASHER を添付"
],
"WorkPoints": [
"取付け方向に注意! この部品には方向性があります",
"JOINT を先に取付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"Pg2",
"Pg1",
"Pg3",
"Pg4"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "架台上面中継JOINT組付け③(j部)",
"WorkItems": [
"1. ①にJOINT ･JOINT ･JOINT を取付",
"2. 1.完成品にJOINT ･JOINT ･JOINT ･JOINT ･JOINT ･JOINT を取付ける",
"3. 2.完成品にﾏｽｷﾝｸﾞﾃｰﾌﾟでﾎﾟｼﾞｼｮﾝ名称を記入する",
"4. 3.完成品にBOLT ･WASHER を添付"
],
"WorkPoints": [
"取付け方向に注意! この部品には方向性があります",
"JOINT を対角に先に付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"Pj2",
"Ej1",
"Pj1",
"Ej2"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "架台上面中継JOINT組付け④(n部)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "架台上面中継JOINT組付け⑤(l部)",
"WorkItems": [
"1. ①にJOINT ･JOINT を取付",
"2. 1.完成品にJOINT ･JOINT ･JOINT ･JOINT を取付",
"3. 2.完成品にﾏｽｷﾝｸﾞﾃｰﾌﾟでﾎﾟｼﾞｼｮﾝ名称を記入する",
"4. 3.完成品にBOLT ･WASHER を添付"
],
"WorkPoints": [
"取付け方向に注意! この部品には方向性があります"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"Vl1",
"Pl2",
"Pl1",
"Vl2"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "架台上面中継JOINT組付け⑥(m部)",
"WorkItems": [
"1. ①にJOINT を取付",
"2. 1.完成品にJOINT ･JOINT を取付",
"3. 2.完成品にﾏｽｷﾝｸﾞﾃｰﾌﾟでﾎﾟｼﾞｼｮﾝ名称を記入する",
"4. 3.完成品にBOLT ･WASHER を添付"
],
"WorkPoints": [
"取付け方向に注意! この部品には方向性があります"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"Vm1",
"Pm1"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "架台上面中継JOINT配管(g部:j部)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "架台上面中継JOINT配管(n部:l部:m部)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3.5m",
"ToolOther": "",
"WorkName": "配管準備①(正圧系)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3.5m",
"ToolOther": "",
"WorkName": "配管準備②(真空系)",
"WorkItems": [
"2. TUBE でｶｯﾄした配管をJOINT JOINT JOINT JOINT JOINT に挿入",
"1. TUBE TUBE を指定の長さでｶｯﾄ"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"真空系",
"TUBE φ12白",
"650mm×1本 500mm×1本300mm×3本",
"200mm×1本",
"部はﾃｰﾌﾟで名称表記する事",
"TUBE φ6白",
"2100mm×1本"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3.5m",
"ToolOther": "",
"WorkName": "配管準備③(排気系)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3.5m",
"ToolOther": "",
"WorkName": "ｴｷｿﾞｰｽﾄﾌｨﾙﾀｰ組立",
"WorkItems": [
"1. EXHAUST-CLEANER にJOINT を取付",
"2. 1.完成品にEXHAUST-CLEANER 付属品を取付",
"3. TUBE を指定の長さにｶｯﾄ",
"4. 2.完成品にTUBE の配管を接続",
"5. 4.完成品にBOLT ･WASHER を付属する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付方向注意"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:750㎜±5㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ｶﾊﾞｰﾛｯｸﾊﾞﾙﾌﾞ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:250㎜±5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ｲｵﾅｲｻﾞｰﾊﾞﾙﾌﾞ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｸﾞﾛﾒｯﾄ前準備",
"WorkItems": [
"1. GROMMET に切り込みを入れる",
"2. 次工程(本体)へ払い出す"
],
"WorkPoints": [
"ｸﾞﾛﾒｯﾄ4個共に切れ込みを入れる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"縦横 約30㎜",
"この作業では同じものを4個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りの寸法で取付いていること指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "5.3N･m",
"WorkName": "部品廃棄BOX前段取り①",
"WorkItems": [
"1. ROD にSCREW を取付ける"
],
"WorkPoints": [
"SCREW がROD の底付きするところまで締める"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります｡",
"この作業では同じものを4個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.3N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "5.5㎜",
"ToolOther": "40cN･m",
"WorkName": "部品廃棄BOX前段取り②",
"WorkItems": [
"1. ①に②と⑯を取付ける",
"2. 1完成品に③を取付ける"
],
"WorkPoints": [
"NUTの方向に注意",
"上方向に押し当てる",
"2個製作",
"LCRﾁｪｯｶ仕様 ･前後の場合 組立不要 ･前のみ 1個製作 ･後ろのみ 1個製作",
"③C2面取り4箇所確認のこと"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "40cN･m",
"WorkName": "部品廃棄BOX前段取り③",
"WorkItems": [
"2. BRACKET にSENSOR をBOLT WASHER WASHER で取付",
"1. BRACKET に⑥を貼付"
],
"WorkPoints": [
"ｾﾝｻのｺﾈｸﾀ挿入口(白色)がﾌﾞﾗｹｯﾄの折り曲げ方向"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"F(ﾌﾛﾝﾄ)",
"85mm",
"取付け方向に注意!この部品には方向性があります｡"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "部品廃棄BOX前段取り③",
"WorkItems": [],
"WorkPoints": [
"BRACKET の貼付ける箇所をｱﾙｺｰﾙにて清掃"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"20mm",
"20mm",
"85mm",
"R(ﾘｱ)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に取付けてある事指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "5.3N･m",
"WorkName": "ﾁｪﾝｼﾞｬｰ前段取り①",
"WorkItems": [
"2. BRACKET にLABEL を貼付ける",
"1. POST にSCREW を取付ける"
],
"WorkPoints": [
"切り欠きから端面まで短い方にSCREW を取付ける",
"BRACKET の貼付ける箇所をｱﾙｺｰﾙにて清掃",
"SCREW がPOST の底付きするところまで締める",
"POST の部品の方向に注意"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"42mm",
"50.5mm"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.3N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾁｪﾝｼﾞｬｰ前段取り①",
"WorkItems": [
"3. BUSH を指定の長さに切る",
"2. BRACKET にLABEL を貼付ける",
"1. POST にSCREW を取付ける"
],
"WorkPoints": [
"6個製作",
"16mmを2個作成",
"切り欠きから端面まで短い方にSCREW を取付ける",
"BRACKET の貼付ける箇所をｱﾙｺｰﾙにて清掃",
"SCREW がPOST の底付きするところまで締める",
"POST の部品の方向に注意"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"42mm",
"50.5mm"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に取付けてある事指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "ﾁｪﾝｼﾞｬｰ前段取り①",
"WorkItems": [
"4. 2完成品にBUSH を取付､JOINT を⑯⑰で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開口部ｾﾝｻｰ組立1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"■1. ②の型式を確認し､ﾛｯﾄNoを検査書に記入",
"検査表①:4.開口部ｾﾝｻｰﾛｯﾄNo記入",
"各2個製作",
"ｾﾝｻ取付け前に検査表記入の事",
"型式 例:E3ZS-T81A-L-2",
"ﾛｯﾄ№(製造番号)",
"2. ①に⑥⑦を貼付",
"■安全作業",
"投光側･受光側の取付に注意",
"3. 2完成品に②を⑯⑰で取付",
"締付ﾄﾙｸ 45cN･m",
"3芯",
"4芯",
"投光側B1046TB1047T",
"受光側B1046B1047",
"7㎜",
"7㎜",
"ﾌﾞﾗｹｯﾄより7㎜位置で取付"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に取付けてある事指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "開口部ｾﾝｻｰ組立1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"投光側･受光側の取付に注意",
"3. 2完成品に②を⑯⑰で取付",
"締付ﾄﾙｸ 45cN･m",
"3芯",
"4芯",
"投光側B1046TB1047T",
"受光側B1046B1047",
"7㎜",
"7㎜",
"ﾌﾞﾗｹｯﾄより7㎜位置で取付",
"■安全作業"
]
} | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開口部ｾﾝｻｰ組立1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"投光側･受光側の取付に注意",
"■1. ②の型式を確認し､ﾛｯﾄNoを検査書に記入",
"検査表①:4.開口部ｾﾝｻｰﾛｯﾄNo記入",
"3. 2完成品に②を⑯⑰で取付",
"各2個製作",
"締付ﾄﾙｸ 45cN･m",
"ｾﾝｻ取付け前に検査表記入の事",
"3芯",
"4芯",
"型式 例:E3ZS-T81A-L-2",
"ﾛｯﾄ№(製造番号)",
"2. ①に⑥⑦を貼付",
"投光側B1046TB1047T",
"受光側B1046B1047",
"7㎜",
"7㎜",
"ﾌﾞﾗｹｯﾄより7㎜位置で取付",
"WEPJ-G002-D06"
]
} | {
"QualityItem": "型式･検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開口部ｾﾝｻ組立2",
"WorkItems": [],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄ端面から50㎜で結束",
"F用",
"投光(3芯)",
"受光(4芯)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"参考 ﾀｲﾒｲﾄ EV07 締付強度指示値 1.5",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"50㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:端面より5㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開口部ｾﾝｻ束線",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"1. ①の配線に印をする",
"ｲﾝｼｭﾛｯｸ端から85mm",
"2. 配線を４つの輪にまとめ㉗で縛る",
"印の位置で㉗で縛る",
"･4つの輪の大きさを合わせる･印の位置がずれないように注意"
]
} | {
"QualityItem": "配線･配管干渉確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｲﾝｼｭﾛｯｸ端から85㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開口部ｾﾝｻ束線",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"1. ①の配線に印をする",
"ｲﾝｼｭﾛｯｸ端から85mm",
"2. 配線を４つの輪にまとめ㉗で縛る",
"印の位置で㉗で縛る",
"･4つの輪の大きさを合わせる･印の位置がずれないように注意"
]
} | {
"QualityItem": "配線･配管干渉確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｺﾈｸﾀ端から85㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "12㎜",
"ToolOther": "5.3N･m",
"WorkName": "熱補正ﾎﾟｰﾙ組立1",
"WorkItems": [
"1. SHAFT にSCREW を締め込む(6本)",
"2. 1の完成品をBAR に取付ける"
],
"WorkPoints": [
"SCREW がSHAFT の底付きするところまで締める",
"6ｹ製作"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"取付け方向に注意!この部品には方向性があります｡"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各5.3N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "5.3N･m",
"WorkName": "熱補正ﾎﾟｰﾙ組立1",
"WorkItems": [
"1. SHAFT にSCREW を締め込む(6本)",
"2. 1の完成品をBAR に取付ける"
],
"WorkPoints": [
"SCREW がSHAFT の底付きするところまで締める",
"6ｹ製作"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"取付け方向に注意!この部品には方向性があります｡"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各5.3N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "接着剤ｽｰﾊﾟｰX",
"WorkName": "熱補正ﾎﾟｰﾙ組立2",
"WorkItems": [],
"WorkPoints": [
"取付け後24Hは硬化させる事",
"作業終了後TARGET を清掃､緩衝材等で保護し傷や汚れを防止する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"接着剤塗布 ｺﾞﾏ粒:各1",
"▲特殊作業"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "熱補正ﾌﾟﾚｰﾄ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5981",
"WorkName": "熱補正ﾎﾟｰﾙ組立2",
"WorkItems": [],
"WorkPoints": [
"取付け後24Hは硬化させる事",
"作業終了後TARGET を清掃､緩衝材等で保護し傷や汚れを防止する",
"取付け後24Hは硬化させる事",
"作業終了後TARGET を清掃､緩衝材等で保護し傷や汚れを防止する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"接着剤塗布 ｺﾞﾏ粒:各1",
"▲特殊作業",
"接着剤塗布 ｺﾞﾏ粒:各1"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5981",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "熱補正ﾎﾟｰﾙ組立2",
"WorkItems": [],
"WorkPoints": [
"取付け後24Hは硬化させる事",
"作業終了後TARGET を清掃､緩衝材等で保護し傷や汚れを防止する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"接着剤塗布 ｺﾞﾏ粒:各1",
"▲特殊作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "50cN･m",
"WorkName": "ﾃｰﾌﾟ浮きｾﾝｻ左側組立1",
"WorkItems": [
"2. SENSOR(600MM) をBRACKET にSENSOR(600MM) SCREW WASHER WASHER で取付ける",
"3. SENSOR(600MM) をBRACKET にSENSOR(600MM) SCREW WASHER WASHER で取付ける",
"■1. 型式を確認し､ﾛｯﾄNo.･ｼﾘｱﾙNo.を記入する"
],
"WorkPoints": [
"ｾﾝｻ:B･C",
"ｾﾝｻ:A･D",
"受光側型式",
"ﾛｯﾄNo.",
"ｼﾘｱﾙNo.",
"ﾌﾟﾚｰﾄの向きに注意する事",
"ﾌﾟﾚｰﾄの向きに注意する事",
"受光側ｾﾝｻ:4個作製",
"受光側ｾﾝｻ:4個作製",
"EX-L212D",
"EX-L212D",
"投光側(ｹｰﾌﾞﾙ灰色)",
"受光側(ｹｰﾌﾞﾙ黒色)"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"■安全作業",
"検査表SENSOR(600MM) :ﾃｰﾌﾟ浮き検出ｾﾝｻの型式確認とﾛｯﾄNo.記録"
]
} | {
"QualityItem": "安全SW締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程",
"安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.