input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄ接続(SAFETY基板)",
"WorkItems": [
"1. ｾﾌﾃｨｰ基板へのｹｰﾌﾞﾙをﾊﾟﾜｰﾕﾆｯﾄに固定する",
"2. ｾﾌﾃｨｰ基板にｺﾈｸﾀを接続する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!",
"17連切替仕様/ﾄﾚｲ仕様のみ接続"
],
"Tolks": [],
"InspectionNo": "WEAV-G002-D06",
"InspectionItems": [
"検査表①:10.Power_Unit確認(R側)"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"EGF",
"EGR",
"HC",
"CV2",
"CBF",
"CBR",
"CAF",
"CAR",
"TBF",
"TBR",
"TAF",
"TAR",
"CV1",
"CV7",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"ｲﾝｼｭﾛｯｸ(200mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"検査表②:4. ｺﾈｸﾀ接続確認",
"WEAV-G002-D06"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D06",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾜｰﾕﾆｯﾄ接続(SAFETY基板)",
"WorkItems": [
"1. ｾﾌﾃｨｰ基板へのｹｰﾌﾞﾙをﾊﾟﾜｰﾕﾆｯﾄに固定する",
"2. ｾﾌﾃｨｰ基板にｺﾈｸﾀを接続する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!",
"17連切替仕様/ﾄﾚｲ仕様のみ接続"
],
"Tolks": [],
"InspectionNo": "WEAV-G002-D14",
"InspectionItems": [
"検査表②:4. ｺﾈｸﾀ接続確認"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"EGF",
"EGR",
"HC",
"CV2",
"CBF",
"CBR",
"CAF",
"CAR",
"TBF",
"TBR",
"TAF",
"TAR",
"CV1",
"CV7",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"ｲﾝｼｭﾛｯｸ(200mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"検査表①:10.Power_Unit確認(R側)",
"WEAV-G002-D14"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D14",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定⑤(右側)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"右外側から見た図",
"穴より上側へ",
"B1046P 他",
"FCDRRP",
"1. 外側に出したｹｰﾌﾞﾙを引き回し､固定する",
"穴より上側へ",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"穴より下側へ",
"連結信号BKT",
"右内側から見た図",
"非常停止ﾎﾞﾀﾝのｹｰﾌﾞﾙを束線に縛り付ける"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒｲﾝｴｱｰ圧ｾﾝｻｰ接続",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"B0116",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!",
"1. ｹｰﾌﾞﾙを架台に固定する",
"2. ﾒｲﾝｴｱｰ圧ｾﾝｻｰｺﾈｸﾀを接続する",
"検査表①:8.R側確認",
"WEAV-G002-D06"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D06",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "+ﾋﾞｯﾄ",
"ToolOther": "43cN･m",
"WorkName": "ﾒｲﾝｴｱｰONﾊﾞﾙﾌﾞ接続",
"WorkItems": [
"1. ﾒｲﾝｴｱｰﾊﾞﾙﾌﾞｺﾈｸﾀを前準備完成品 で接続する"
],
"WorkPoints": [
"ﾊﾟｯｷﾝ",
"ﾎﾞﾙﾄ",
"取付方向"
],
"Tolks": [
"締付ﾄﾙｸ 55cN･m",
"締付ﾄﾙｸ 43cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"R301",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"検査表前準備完成品 :8.R側確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒｲﾝｴｱｰONﾊﾞﾙﾌﾞ接続",
"WorkItems": [
"1. ﾒｲﾝｴｱｰﾊﾞﾙﾌﾞｺﾈｸﾀを前準備完成品 で接続する"
],
"WorkPoints": [
"ﾊﾟｯｷﾝ",
"ﾎﾞﾙﾄ",
"取付方向"
],
"Tolks": [
"締付ﾄﾙｸ 55cN･m",
"締付ﾄﾙｸ 43cN･m"
],
"InspectionNo": "WEAV-G002-D06",
"InspectionItems": [
"検査表前準備完成品 :8.R側確認"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"R301",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"WEAV-G002-D06"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D06",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ｾﾝｻｰ中継ｹｰﾌﾞﾙ取付け/ｾﾝｻｰ中継ﾌﾞﾗｹｯﾄ取付け(右側)",
"WorkItems": [
"1. ｾﾝｻｰ中継ｺﾈｸﾀを①に嵌め込む",
"2. ①を⑯⑰にて取付ける"
],
"WorkPoints": [
"ｼｰﾙと名称が合っているか確認",
"ｺﾈｸﾀの形状･方向･名称をよく確認して嵌め込むこと!",
"しっかりと嵌め込まれているか押して確認すること"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"B1046P",
"B1237TP",
"B1240TP",
"B1241TP",
"B1242TP"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "連結信号ﾌﾞﾗｹｯﾄ取付け(右側)",
"WorkItems": [
"2. 連結信号ﾌﾞﾗｹｯﾄをBOLT WASHER にて取付ける",
"1. ｹｰﾌﾞﾙを架台に固定する"
],
"WorkPoints": [
"外側から見た図"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定②(左側)(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様、ｼﾝｸﾞﾙｺﾝﾍﾞｱ奥基準仕様、30連台車仕様あり)",
"WorkItems": [
"1. 左側面のｹｰﾌﾞﾙを固定する"
],
"WorkPoints": [
"穴より外側へ",
"･ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様時･ｼﾝｸﾞﾙｺﾝﾍﾞｱ奥基準仕様時"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ(200mm)",
"CART.R1",
"B1226R,B1227R 他",
"B1247TP,TRAY.SR,連結BKT,R4204R 他",
"***K324",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"ｲﾝｼｭﾛｯｸ(100mm)30連台車仕様時のみ固定する",
"CN3K504",
"CN3K503"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "搬送中継基板接続(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様、ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様あり)",
"WorkItems": [
"1. 搬送中継基板にｺﾈｸﾀを接続する"
],
"WorkPoints": [
"K323",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!",
"ｼﾝｸﾞﾙｺﾝﾍﾞｱ奥基準仕様時はここでまとめる",
"ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様時ｼﾝｸﾞﾙｺﾝﾍﾞｱ手前基準仕様時"
],
"Tolks": [],
"InspectionNo": "WEAV-G002-D06",
"InspectionItems": [
"検査表①:12.CN中継基板(R側)"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"TP",
"M9",
"TM",
"OSP",
"OSR",
"M9",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WEAV-G002-D06"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D06",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "搬送中継基板接続(OP:ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様、ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様あり)",
"WorkItems": [
"1. 搬送中継基板にｺﾈｸﾀを接続する"
],
"WorkPoints": [
"K323",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!",
"ｼﾝｸﾞﾙｺﾝﾍﾞｱ奥基準仕様時はここでまとめる",
"ﾃﾞｭｱﾙｺﾝﾍﾞｱ仕様時ｼﾝｸﾞﾙｺﾝﾍﾞｱ手前基準仕様時"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"TP",
"M9",
"TM",
"OSP",
"OSR",
"検査表①:12.CN中継基板(R側)",
"M9",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WEAV-G002-D08"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D08",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶｯﾀｰﾊﾞﾙﾌﾞ接続",
"WorkItems": [
"1. ｶｯﾀｰﾊﾞﾙﾌﾞにｺﾈｸﾀを接続する",
"2. ﾌｨｰﾀﾞｰｶﾊﾞｰ中継ｺﾈｸﾀをﾌﾞﾗｹｯﾄに取付ける"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!"
],
"Tolks": [],
"InspectionNo": "WEAV-G002-D06",
"InspectionItems": [
"検査表①:8.R側確認",
"検査表①:8.R側確認"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"R4205Rﾃｰﾌﾟｶｯﾀｰ:R1(左側)",
"R4705Rﾃｰﾌﾟｶｯﾀｰ:R2(右側)",
"S0737P",
"WEAV-G002-D06"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D06",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｹｰﾌﾞﾙ引き回し・固定③(左側)(OP:17連切替仕様、ﾄﾚｲ仕様あり)",
"WorkItems": [
"1. 外側に出したｹｰﾌﾞﾙを引き回し､固定する"
],
"WorkPoints": [
"左外側から見た図",
"穴より上側へ",
"･17連切替仕様時･ﾄﾚｲ仕様時"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"B1047TP 他",
"TRAY.SR",
"FCDLRP",
"TRAY.SR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"連結信号BKT",
"R4204R 他",
"R4204R 他"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ接続",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"1. 台車駆動ﾊﾞﾙﾌﾞにｹｰﾌﾞﾙを接続する",
"R4704R台車ﾛｯｸ:R2(右側)",
"R4204R台車ﾛｯｸ:R1(左側)",
"R4706R台車ﾘﾘｰｽ:R2(右側)",
"R4206R台車ﾘﾘｰｽ:R1(左側)",
"検査表①:8.R側確認",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"■30連台車仕様 R4704R, R4706Rは折り返してｲﾝｼｭﾛｯｸで固定する■ﾄﾚｲ仕様 R4204R, R4206Rは折り返してｲﾝｼｭﾛｯｸで固定する",
"※30連台車仕様/ﾄﾚｲ仕様時､図の台車駆動ﾊﾞﾙﾌﾞは1個",
"WEAV-G002-D06"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D06",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲ信号ｹｰﾌﾞﾙ取付け(OP:17連切替仕様、ﾄﾚｲ仕様)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"1. ﾄﾚｲ信号ｹｰﾌﾞﾙを接続する",
"検査表①:4. ｺﾈｸﾀ接続確認",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!",
"TRAY.SR",
"WEAV-G002-D14"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D14",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ｾﾝｻｰ中継ｹｰﾌﾞﾙ取付け/ｾﾝｻｰ中継ﾌﾞﾗｹｯﾄ取付け(左側)",
"WorkItems": [
"1. ｾﾝｻｰ中継ｺﾈｸﾀをBRACKET に嵌め込む",
"2. BRACKET をBOLT WASHER にて取付ける"
],
"WorkPoints": [
"ｼｰﾙと名称が合っているか確認",
"ｺﾈｸﾀの形状･方向･名称をよく確認して嵌め込むこと!",
"しっかりと嵌め込まれているか押して確認すること"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "連結信号ﾌﾞﾗｹｯﾄ取付け(左側)",
"WorkItems": [
"1. CNLNｹｰﾌﾞﾙを連結信号ﾌﾞﾗｹｯﾄに接続する",
"2. 連結信号ﾌﾞﾗｹｯﾄをBOLT WASHER にて取付ける"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!",
"ｶﾁｯと音がする所まで差込む"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"CNLN"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【WX専用】中継ﾌﾞﾗｹｯﾄｹｰﾌﾞﾙ固定・接続",
"WorkItems": [
"1. 中継ﾌﾞﾗｹｯﾄｹｰﾌﾞﾙを固定する",
"2. ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄに巻きつけて固定",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!"
],
"Tolks": [],
"InspectionNo": "WEAV-G002-D06",
"InspectionItems": [
"検査表①:10.ﾊﾟﾜｰﾕﾆｯﾄ確認(R側)"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"TP2R",
"TP1R",
"MCFR",
"CAF24VR",
"CAR24VR",
"CARTR",
"FANGR",
"MCRR",
"WEAV-G002-D06"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D06",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "I/O中継基板接続(OP:F側ﾄﾚｲｽﾄｯｶｰ仕様あり)",
"WorkItems": [
"1. I/O中継基板にｺﾈｸﾀを接続する"
],
"WorkPoints": [
"K322",
"ｺﾈｸﾀの形状･方向｡名称をよく確認して接続すること!"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"ST",
"CLB",
"SW3",
"IO",
"CRB",
"DB",
"BL",
"LPA",
"FB2",
"FB1",
"SW1",
"SW2",
"CLA",
"CG",
"CRA",
"FA2",
"FA1",
"検査表①:12.CN中継基板(R側)",
"FB3",
"WEAV-G002-D06WEMA-G002-D08"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D06WEMA-G002-D08",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "+№1",
"ToolOther": "15cN･m",
"WorkName": "【WX専用】ﾄﾞﾗｲﾊﾞｰDCｹｰﾌﾞﾙ接続",
"WorkItems": [
"■1. X軸及びY軸ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰにｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!",
"上下均等に取付けﾈｼﾞを締め込んでいく"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WEAV-G002-D06",
"InspectionItems": [
"検査表①:9.ﾓｰﾀｰﾄﾞﾗｲﾊﾞｰ確認(R側)",
"検査表①:9.ﾓｰﾀｰﾄﾞﾗｲﾊﾞｰ確認(R側)"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"CN3K504",
"CN3K503",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【WX専用】ﾄﾞﾗｲﾊﾞｰDCｹｰﾌﾞﾙ接続",
"WorkItems": [
"■1. X軸及びY軸ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰにｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!",
"上下均等に取付けﾈｼﾞを締め込んでいく"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WEAV-G002-D06",
"InspectionItems": [
"検査表①:9.ﾓｰﾀｰﾄﾞﾗｲﾊﾞｰ確認(R側)",
"検査表①:9.ﾓｰﾀｰﾄﾞﾗｲﾊﾞｰ確認(R側)"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"CN3K504",
"CN3K503",
"WEAV-G002-D06"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "FAN・ｺﾈｸﾀﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. BRACKET をBOLT WASHER にて取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜ﾎﾞｰﾙ",
"ToolOther": "3.2N･m",
"WorkName": "FAN・ｺﾈｸﾀﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"2. 前準備完成品 FAN-GUARD をBOLT WASHER にて取付ける",
"3. ｹｰﾌﾞﾙを固定する"
],
"WorkPoints": [
"ｹｰﾌﾞﾙ",
"FANの取付方向に注意すること",
"FANｶﾞｰﾄﾞの取付方向に注意すること"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "銘板貼付治具",
"Size": "",
"ToolOther": "FM-4970",
"WorkName": "FAN・ｺﾈｸﾀﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"4. 治具を使用しLABEL を架台に貼付ける"
],
"WorkPoints": [
"ﾌｧﾝﾓｰﾀｰ端面と治具端面を合わせる",
"貼付ける前に清掃し向きに注意して貼付けること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-4970",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の位置に貼付されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｧﾝﾓｰﾀｰｹｰﾌﾞﾙ固定・接続",
"WorkItems": [
"1. ﾌｧﾝﾓｰﾀｰｹｰﾌﾞﾙG112Pを固定する",
"2. G112Pをﾌﾞﾗｹｯﾄに嵌め込む",
"3. G112Rを接続する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!"
],
"Tolks": [],
"InspectionNo": "WEAV-G002-D06",
"InspectionItems": [
"検査表①:8.R側確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"G112P",
"G112R",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"WEAV-G002-D06"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "24V電源ﾕﾆｯﾄ取付け",
"WorkItems": [
"2. 前準備完成品 をWASHER BOLT にて取付ける",
"1. SPACER をBOLT WASHER にて取付ける"
],
"WorkPoints": [
"後ろ2か所は固定用ｽﾍﾟｰｻｰに嵌めこむ"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "24V電源ﾕﾆｯﾄ接続",
"WorkItems": [
"1. 24V電源ﾕﾆｯﾄにｺﾈｸﾀを接続する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!"
],
"Tolks": [],
"InspectionNo": "WEAV-G002-D06",
"InspectionItems": [
"検査表①:11.24V電源ﾕﾆｯﾄ:確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"CBF24",
"CBR24",
"24VOT",
"1 T113",
"WEAV-G002-D06"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "真空ﾎﾟﾝﾌﾟ取付け・接続",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"1. SPACER をBOLT WASHER にて取付ける",
"締付ﾄﾙｸ 6.0N･m",
"右2か所は固定用ｽﾍﾟｰｻｰにはめこむ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "真空ﾎﾟﾝﾌﾟ取付け・接続",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"締付ﾄﾙｸ 20.5N･m",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"PUMP",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!",
"検査表SPACER :10.POWER_UNIT確認(R側)",
"2. 前準備完成品 をBOLT WASHER にて取付ける",
"3. 真空ﾎﾟﾝﾌﾟ電源ｹｰﾌﾞﾙを固定する",
"4. 真空ﾎﾟﾝﾌﾟ電源ｺﾈｸﾀを接続する"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "真空ﾎﾟﾝﾌﾟ取付け・接続",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"1. SPACER をBOLT WASHER にて取付ける",
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 20.5N･m",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"PUMP",
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!",
"検査表SPACER :10.POWER_UNIT確認(R側)",
"右2か所は固定用ｽﾍﾟｰｻｰにはめこむ",
"2. 前準備完成品 をBOLT WASHER にて取付ける",
"3. 真空ﾎﾟﾝﾌﾟ電源ｹｰﾌﾞﾙを固定する",
"4. 真空ﾎﾟﾝﾌﾟ電源ｺﾈｸﾀを接続する",
"WEAV-G002-D06"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "24V電源ﾕﾆｯﾄACｺﾈｸﾀ接続",
"WorkItems": [
"1. 電源ｹｰﾌﾞﾙを固定しｺﾈｸﾀを接続する"
],
"WorkPoints": [
"ｺﾈｸﾀの形状･方向･名称をよく確認して接続すること!"
],
"Tolks": [],
"InspectionNo": "WEAV-G002-D06",
"InspectionItems": [
"検査表①:10.POWER_UNIT確認(R側)"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"T2A11",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"WEAV-G002-D06"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続されている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "+ﾋﾞｯﾄ",
"ToolOther": "3.0N･m",
"WorkName": "台車中継ﾌﾞﾗｹｯﾄ取付け(右側)",
"WorkItems": [
"1. 前準備完成品 にｺﾈｸﾀ(FCDRRP)を取付ける",
"2. 前準備完成品 に配管(215R,216R)を接続する",
"3. 前準備完成品 を架台にSCREW にて取付ける"
],
"WorkPoints": [
"JSTと表示されている方を上向きに取付ける",
"取付け後配管折れ等が無いか確認する",
"しっかり接続されているか引っ張って確認すること",
"ｶﾁｯと音がする所まで差込む"
],
"Tolks": [
"締付ﾄﾙｸ 3.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"216R",
"215R",
"FCDRRP"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板ﾎﾙﾀﾞｰ・ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ配管(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様、30連台車仕様あり)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"202L",
"1. 架台に配管を固定する",
"2. ﾍﾞｰｽ上に配管(202L, 204L)を上げる",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"204L",
"304L",
"穴から上へ",
"ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様の場合はここでまとめて固定する",
"30連台車仕様時はここでまとめて固定する"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "真空ﾎﾟﾝﾌﾟ配管固定(右側)",
"WorkItems": [
"1. 架台に配管を固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "真空ﾎﾟﾝﾌﾟ配管固定(左側)",
"WorkItems": [
"1. 架台に配管を固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "真空ﾎﾟﾝﾌﾟ配管固定(中央)",
"WorkItems": [
"1. 架台に配管を固定する"
],
"WorkPoints": [
"24電源ﾕﾆｯﾄの電源ｹｰﾌﾞﾙも一緒に固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "真空ﾎﾟﾝﾌﾟ配管接続",
"WorkItems": [
"2. 接続した配管をｲﾝｼｭﾛｯｸで束ねる",
"1. 真空ﾎﾟﾝﾌﾟに配管(701L,702L,701R,702R,401)を接続する"
],
"WorkPoints": [
"しっかり接続されているか引っ張って確認すること"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"701L",
"702L",
"701R",
"702R"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶｯﾀｰﾊﾞﾙﾌﾞ配管接続(OP:ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様、30連台車仕様あり)",
"WorkItems": [
"1. ｶｯﾀｰﾊﾞﾙﾌﾞに配管(205R)を接続する",
"2. 架台に配管を固定する",
"3. ﾍﾞｰｽ上に配管(203R)を上げる"
],
"WorkPoints": [
"しっかり接続されているか引っ張って確認すること",
"ｼﾝｸﾞﾙｺﾝﾍﾞｱ仕様時はここでまとめて固定する",
"30連台車仕様時",
"17連/切替/ﾄﾚｲ仕様時",
"30連台車仕様時のみ固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"203R",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"205R",
"304R"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "+ﾋﾞｯﾄ",
"ToolOther": "3.0N･m",
"WorkName": "台車中継ﾌﾞﾗｹｯﾄ取付け(左側)",
"WorkItems": [
"1. 前準備完成品 or 前準備完成品 にｺﾈｸﾀ(FCDLRP)を取付ける",
"2. 前準備完成品 or 前準備完成品 に配管(215L,216L)を接続する",
"3. 前準備完成品 or 前準備完成品 を架台にSCREW にて取付ける"
],
"WorkPoints": [
"JSTと表示されている方を上向きに取付ける",
"取付け後配管折れ等が無いか確認する",
"しっかり接続されているか引っ張って確認すること",
"ｶﾁｯと音がする所まで差込む"
],
"Tolks": [
"締付ﾄﾙｸ 3.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"216L",
"215L",
"FCDLRP",
"or"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "台車駆動ﾊﾞﾙﾌﾞ配管接続",
"WorkItems": [
"3. 配管を架台に固定する",
"2. 台車駆動ﾊﾞﾙﾌﾞに配管(215L, 216L, 215R, 216R, 505R)を接続する",
"1. 配管(302)を空いている継ぎ手に接続する"
],
"WorkPoints": [
"しっかり接続されているか引っ張って確認すること",
"30連台車仕様",
"30連台車仕様以外"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"505R",
"216R",
"215L",
"216L",
"215R",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"･ｹｰﾌﾞﾙ付属ﾏｳﾝﾄ を差込み固定",
"216R",
"215L",
"216L",
"215R"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾚｲ中継ﾌﾞﾗｹｯﾄ配管接続(OP:17連切替仕様、ﾄﾚｲ仕様あり)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"REAR",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"17連切替仕様/ﾄﾚｲ仕様時のみ実施",
"1. ﾄﾚｲ中継ﾌﾞﾗｹｯﾄに配管(504R)を接続する",
"2. 配管を架台に固定する",
"504R",
"しっかり接続されているか引っ張って確認すること",
"17連台車仕様/30連台車仕様時はここでまとめて固定する"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "X軸仮取付け(FRONT-右側)",
"WorkItems": [
"◆2. 前準備完成品 をｽﾗｲﾄﾞさせながら載せこんで行く"
],
"WorkPoints": [
"二人作業で行う",
"ﾌﾛﾝﾄ側作業者",
"ﾘｱ側作業者",
"取付穴とﾎﾞﾙﾄのｾﾝﾀｰ確認"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"◆作業者安全作業"
],
"Words": [
"FRONT",
"REAR",
"押し当てる",
"数回揺さぶる",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "【WX専用】X軸仮取付け(REAR-左側)",
"WorkItems": [
"2. ｽﾗｲﾀﾞｰとの位置を合わせBOLT WASHER にて仮取付けする",
"3. ﾌﾛﾝﾄ側作業者に押し当ててもらっている状態で4点仮締めする"
],
"WorkPoints": [
"ﾎﾞﾙﾄを締付ける手前まで入れる",
"取付け穴に対しﾎﾞﾙﾄがほぼｾﾝﾀｰあるか確認してから締める",
"SD-EJM9D01-099にて本締め実施"
],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"押し当ててもらう",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【WX専用】Y軸ｽﾄｯﾊﾟｰ仮取付け(左側)",
"WorkItems": [
"1. 前準備完成品 をBOLT で仮取付けする"
],
"WorkPoints": [
"SD-EJM9D01-301で本締め実施"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"FRONT",
"REAR"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【WX専用】ｸﾞﾘｰｽﾆｯﾌﾟﾙ取付け",
"WorkItems": [
"1. GREASE-NIPPLE を取付ける"
],
"WorkPoints": [
"右側も同様に取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "WEAV-G002-C02",
"InspectionItems": [
"検査表GREASE-NIPPLE :3. Y軸ﾘﾆｱｶﾞｲﾄﾞのｸﾞﾘｰｽﾆｯﾌﾟﾙ方向確認"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"FRONT",
"REAR",
"WEAV-G002-C02"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り取付されている事",
"Method": "目視",
"RecordMethod": "WEAV-G002-C02",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "BOX7㎜",
"ToolOther": "15cN･m",
"WorkName": "【WX専用】ｸﾞﾘｰｽﾆｯﾌﾟﾙ取付け",
"WorkItems": [
"1. GREASE-NIPPLE を取付ける"
],
"WorkPoints": [
"右側も同様に取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"FRONT",
"REAR",
"検査表GREASE-NIPPLE :3. Y軸ﾘﾆｱｶﾞｲﾄﾞのｸﾞﾘｰｽﾆｯﾌﾟﾙ方向確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【WX専用】ｸﾞﾘｰｽﾁｭｰﾌﾞ差込み",
"WorkItems": [
"1. ｸﾞﾘｰｽﾁｭｰﾌﾞを差込む"
],
"WorkPoints": [
"ｴﾙﾎﾞに4φTUBE(ｸﾘｱ)を差込む",
"右側も同様に差込む"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"FRONT",
"REAR"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XY直角度計測ﾍｯﾄﾞ",
"Size": "",
"ToolOther": "FM-2413",
"WorkName": "【WX専用】XY度計測ﾍｯﾄﾞ取付け",
"WorkItems": [
"1. X軸駆動部に計測ﾍｯﾄﾞ治具を搭載する"
],
"WorkPoints": [
"この溝に引っ掛ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-2413",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "XYﾕﾆｯﾄﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2224",
"WorkName": "XYﾁｪｯｶｰ準備",
"WorkItems": [
"1. 電源ｹｰﾌﾞﾙを接続する",
"2. ﾊﾟｿｺﾝの電源をONする",
"3. ﾊﾟｿｺﾝを立ち上げる",
"4. CounterDisplayを起動する"
],
"WorkPoints": [
"XYﾕﾆｯﾄﾁｪｯｶｰ",
"fajapanと入力",
"Ctrl + Alt + Del を押す",
"ﾕｰｻﾞｰ名,ﾊﾟｽﾜｰﾄﾞを入力",
"ﾀﾞﾌﾞﾙｸﾘｯｸ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｽﾗｲﾄﾞする"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "FM-2224",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "XY直角度計測ﾍｯﾄﾞ(FRONT)⇔XYﾁｪｯｶｰ接続",
"WorkItems": [
"1. ｺﾝﾄﾛｰﾗｰ電源がOFFになっているかを確認する",
"2. 信号ｹｰﾌﾞﾙを取り出す",
"4. ｺﾝﾄﾛｰﾗｰ電源をONにする",
"3. FRONT計測ﾍｯﾄﾞｾﾝｻｰｹｰﾌﾞﾙと接続する"
],
"WorkPoints": [
"XYﾕﾆｯﾄﾁｪｯｶｰ",
"溝と突起を合わせ差込み矢印方向に回転させる",
"FRONT計測ﾍｯﾄﾞｾﾝｻｰｹｰﾌﾞﾙ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【WX専用】XY直角度計測ﾍｯﾄﾞ(REAR)⇔XYﾁｪｯｶｰ接続",
"WorkItems": [
"4. ｺﾝﾄﾛｰﾗｰ電源をONにする",
"3. REAR計測ﾍｯﾄﾞｾﾝｻｰｹｰﾌﾞﾙと接続する",
"1. ｺﾝﾄﾛｰﾗｰ電源をOFFにする",
"2. FRONT計測ﾍｯﾄﾞｾﾝｻｰｹｰﾌﾞﾙを外す"
],
"WorkPoints": [
"XYﾕﾆｯﾄﾁｪｯｶｰ",
"溝と突起を合わせ差込み矢印方向に回転させる",
"FRONT計測ﾍｯﾄﾞｾﾝｻｰｹｰﾌﾞﾙ",
"矢印方向に回転させて溝と突起を合わせ外す",
"REAR計測ﾍｯﾄﾞｾﾝｻｰｹｰﾌﾞﾙ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【WX専用】XY直角度計測ﾍｯﾄﾞ取外し",
"WorkItems": [
"1. 駆動部に仕込んであるﾎﾞﾙﾄを緩める(3ヶ所)",
"2. 計測ﾍｯﾄﾞ治具を取り外す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"FRONT"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "【WX専用】Xﾋﾞｰﾑ本取付け(REAR-右側)",
"WorkItems": [
"1. Xﾋﾞｰﾑ取付けﾎﾞﾙﾄの本締めを行う(12ヵ所)"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"REAR",
"FRONT"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "Xﾋﾞｰﾑ本取付け(FRONT-右側)",
"WorkItems": [
"1. Xﾋﾞｰﾑ取付けﾎﾞﾙﾄの本締めを行う(12ヵ所)"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"FRONT",
"REAR"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "Yﾌﾚｰﾑ(3)仮取付け(右側)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1. ﾌﾛﾝﾄ側Xﾋﾞｰﾑをﾘｱ側まで移動する",
"FRONT",
"5. Y-FRAME(3) をBOLT BOLT にて仮取付けする",
"SD-EJM9D01-298にて本締め実施",
"2. 架台への取付面及び固定子取付面に砥石をかける",
"砥石をかけた後ｱﾙｺｰﾙにて清掃する",
"3. Y-FRAME(3) の底面に防錆油を塗布する",
"防錆油が垂れないように注意すること",
"4. Y-FRAME(3) をﾋﾟﾝに合わせて嵌め込む"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "ｽﾄｯﾊﾟｰ及びYﾌﾚｰﾑ(3)本取付け(右側)",
"WorkItems": [
"2. 架台に取付ける4本を締付ける",
"3. Yﾌﾚｰﾑに取付ける5本を締付ける"
],
"WorkPoints": [
"Yﾌﾚｰﾑを押さえた状態で締付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "ｽﾄｯﾊﾟｰ及びYﾌﾚｰﾑ(3)本取付け(右側)",
"WorkItems": [
"4. Yﾌﾚｰﾑを本取付けする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m",
"締付ﾄﾙｸ 20.5N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "【WX専用】Yﾌﾚｰﾑ(2)取付け(右側)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【WX専用】Yﾌﾚｰﾑ(1)仮取付け(右側)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"1. ﾘｱ側Xﾋﾞｰﾑをﾌﾛﾝﾄ側まで移動する",
"REAR",
"ﾘｱ側作業の完了を確認すること",
"4. Y-FRAME(1) をﾋﾟﾝに合わせて嵌め込む",
"5. Y-FRAME(1) をBOLT BOLT にて仮取付けする",
"SD-EJM9D01-301にて本締め実施",
"2. 架台への取付面及び固定子取付面に砥石をかける",
"砥石をかけた後ｱﾙｺｰﾙにて清掃する",
"3. Y-FRAME(1) の底面に防錆油を塗布する",
"防錆油が垂れないように注意すること"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "150cN･m",
"WorkName": "Y-FRAME安全対策PLATE取付け(REAR)",
"WorkItems": [
"1. ①にCOVER をBOLT で取付ける"
],
"WorkPoints": [
"参考:拡大図"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20.5N･m",
"WorkName": "【WX専用】ｽﾄｯﾊﾟｰ及びYﾌﾚｰﾑ(1)本取付け(右側)",
"WorkItems": [
"1. ｽﾄｯﾊﾟｰにBOLT を仮入れする",
"2. 架台に取付ける4本を締付ける",
"4. Yﾌﾚｰﾑを本取付けする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "【WX専用】ｽﾄｯﾊﾟｰ及びYﾌﾚｰﾑ(1)本取付け(右側)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m",
"締付ﾄﾙｸ 20.5N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "操作ﾊﾟﾈﾙｹｰﾌﾞﾙ固定(REAR)",
"WorkItems": [
"1. ｽﾄｯﾊﾟｰにｹｰﾌﾞﾙを固定する"
],
"WorkPoints": [
"配線出代:ｺﾈｸﾀより10~15㎜の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(100mm)",
"RSW2R",
"RSW1R",
"S312P",
"2A04",
"1A04",
"3A04",
"G104P",
"B212P",
"11S202~32S202",
"S312P"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "操作ﾊﾟﾈﾙｹｰﾌﾞﾙ固定(REAR)",
"WorkItems": [
"1. ｽﾄｯﾊﾟｰにｹｰﾌﾞﾙを固定する"
],
"WorkPoints": [
"配線出代:ｺﾈｸﾀより10~15㎜の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(100mm)",
"RSW2R",
"RSW1R",
"S312P",
"2A04",
"1A04",
"3A04",
"G104P",
"B212P",
"11S202~32S202",
"S312P"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:10~15㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "水準器",
"Size": "",
"ToolOther": "0.02㎜/m",
"WorkName": "XYﾕﾆｯﾄ取付後の架台ﾚﾍﾞﾙの確認",
"WorkItems": [
"1. 水準器設置箇所をｳｴｽにてふきあげる",
"2. ﾏｼﾝのﾚﾍﾞﾙを確認する"
],
"WorkPoints": [
"ｸﾞﾘｰｽ･異物無き事",
"規格値:0.06㎜/m",
"目標値は2目盛とする",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄA･B･C･D･E･Fの浮きが無い事",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄ"
],
"Tolks": [],
"InspectionNo": "WEAV-G002-C02",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"WEAV-G002-C02"
]
} | {
"QualityItem": "水平確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.06㎜/m以下",
"Method": "水準器",
"RecordMethod": "WEAV-G002-C02",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "68cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立1",
"WorkItems": [
"1. ①②に砥石をかける",
"2. 1完成品に③④⑤⑥を取付"
],
"WorkPoints": [
"可動側",
"固定側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "68cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立2",
"WorkItems": [
"1. ①②にGUIDE をBOLT WASHER で仮取付",
"2. 1完成品にGUIDE をBOLT で取付"
],
"WorkPoints": [
"仮止め:ﾃﾞｭｱﾙｺﾝﾍﾞﾔ後組工程にて本締め",
"軽く締め付けておく事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.8㎜",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立2",
"WorkItems": [
"1. ①②にGUIDE をBOLT WASHER で仮取付",
"2. 1完成品にGUIDE をBOLT で取付"
],
"WorkPoints": [
"仮止め:ﾃﾞｭｱﾙｺﾝﾍﾞﾔ後組工程にて本締め",
"軽く締め付けておく事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.8㎜ｼｯｸﾈｽｹﾞｰｼﾞを挟んで取付",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.8㎜",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立2",
"WorkItems": [
"1. ①②にGUIDE をBOLT WASHER で仮取付",
"2. 1完成品にGUIDE をBOLT で取付"
],
"WorkPoints": [
"仮止め:ﾃﾞｭｱﾙｺﾝﾍﾞﾔ後組工程にて本締め",
"軽く締め付けておく事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.7㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.8㎜",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立2",
"WorkItems": [
"1. ①②にGUIDE をBOLT WASHER で仮取付",
"2. 1完成品にGUIDE をBOLT で取付"
],
"WorkPoints": [
"仮止め:ﾃﾞｭｱﾙｺﾝﾍﾞﾔ後組工程にて本締め",
"軽く締め付けておく事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.9㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "基板ｶﾞｲﾄﾞ位置出し治具(待機部)",
"Size": "",
"ToolOther": "FM-2845",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立3",
"WorkItems": [
"1. ①②のガイド位置を㉗で仮調整"
],
"WorkPoints": [
"治具使用例",
"2.8mm",
"調整時ガイドの出代を㉘で17mmにだいたい合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"仮止め:ｼﾝｸﾞﾙｺﾝﾍﾞﾔ後組工程にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2845",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "基板ｶﾞｲﾄﾞ位置出し治具(待機部)",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "17㎜",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立3",
"WorkItems": [
"1. ①②のガイド位置を㉗で仮調整"
],
"WorkPoints": [
"治具使用例",
"2.8mm",
"調整時ガイドの出代を㉘で17mmにだいたい合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"仮止め:ｼﾝｸﾞﾙｺﾝﾍﾞﾔ後組工程にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "17㎜を挟んで取付ける事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立4",
"WorkItems": [
"1. ①②にPLATE をBOLT で取付",
"2. 1完成品にPLATE PLATE をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "10㎜",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立4",
"WorkItems": [
"1. ①②にPLATE をBOLT で取付",
"2. 1完成品にPLATE PLATE をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "10㎜を挟んで取付ける事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "10㎜",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立4",
"WorkItems": [
"1. ①②にPLATE をBOLT で取付",
"2. 1完成品にPLATE PLATE をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "5㎜を挟んで取付ける事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立4",
"WorkItems": [
"1. ①②にPLATE をBOLT で取付",
"2. 1完成品にPLATE PLATE をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.5㎜",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立4",
"WorkItems": [
"1. ①②にPLATE をBOLT で取付",
"2. 1完成品にPLATE PLATE をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜を挟み取付ける事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立5",
"WorkItems": [
"1. ①②にCABLE-SUPPORT を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "圧入台",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立6",
"WorkItems": [
"1. 仕様の左右で固定側になる側①②のどちらかにPLATE をBOLT WASHER で取付",
"2. ①②にLABEL ⑦を貼付"
],
"WorkPoints": [
"45mm",
"80mm",
"28mm",
"24mm",
"PLATE を矢印方向に寄せて取付",
"固定側(左側延長)/可動側(右側延長)",
"左側延長取付用"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(延長ｺﾝﾍﾞﾔｰ)",
"Size": "",
"ToolOther": "FM-6620",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立6",
"WorkItems": [
"1. 仕様の左右で固定側になる側①②のどちらかにPLATE をBOLT WASHER で取付",
"2. ①②にLABEL ⑦を貼付"
],
"WorkPoints": [
"45mm",
"80mm",
"28mm",
"24mm",
"1mm",
"45mm",
"24mm",
"PLATE を矢印方向に寄せて取付",
"固定側(左側延長)/可動側(右側延長)",
"可動側(左側延長)/固定側(右側延長)",
"左側延長取付用",
"右側延長取付用"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-6620",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ｿｹｯﾄ4.5㎜",
"ToolOther": "40cN･m",
"WorkName": "振動抑制ｼﾘﾝﾀﾞ組立1",
"WorkItems": [
"2. 1完成品にCAP NUT を取付",
"1. CYLINDER にJOINT を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "0.5N･m",
"WorkName": "振動抑制ｼﾘﾝﾀﾞ組立1",
"WorkItems": [
"2. 1完成品にCAP NUT を取付",
"1. CYLINDER にJOINT を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "0.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "80cN･m",
"WorkName": "振動抑制ｼﾘﾝﾀﾞ組立2",
"WorkItems": [
"2. 1完成品にSTOPPER をBOLT WASHER WASHER で取付",
"1. BRACKET にSTOPPER をはめる"
],
"WorkPoints": [
"延長ｺﾝﾍﾞﾔ右側取付用",
"延長ｺﾝﾍﾞﾔ左側取付用",
"延長ｺﾝﾍﾞﾔ右側取付用",
"㉘を挟んで締付け",
"1.5mm",
"1.5mm",
"㉘を挟んで締付け",
"仕様に合わせてどちらかで組立てる事",
"延長ｺﾝﾍﾞﾔ左側取付用"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "1.5㎜",
"ToolOther": "",
"WorkName": "振動抑制ｼﾘﾝﾀﾞ組立2",
"WorkItems": [
"2. 1完成品にSTOPPER をBOLT WASHER WASHER で取付",
"1. BRACKET にSTOPPER をはめる"
],
"WorkPoints": [
"延長ｺﾝﾍﾞﾔ右側取付用",
"延長ｺﾝﾍﾞﾔ左側取付用",
"延長ｺﾝﾍﾞﾔ右側取付用",
"㉘を挟んで締付け",
"1.5mm",
"1.5mm",
"㉘を挟んで締付け",
"仕様に合わせてどちらかで組立てる事",
"延長ｺﾝﾍﾞﾔ左側取付用"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "1.5㎜を挟んで取付ける事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "80cN･m",
"WorkName": "振動抑制ｼﾘﾝﾀﾞ組立3",
"WorkItems": [
"1. ①に②をBOLT で取付"
],
"WorkPoints": [
"仕様に合わせてどちらかで組立てる事"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.8㎜",
"ToolOther": "10cN･m",
"WorkName": "振動抑制ｼﾘﾝﾀﾞ組立3",
"WorkItems": [
"3. PHﾁｪｯｶで確認",
"2. 1完成品にSWITCH(450MM) を取付"
],
"WorkPoints": [
"縮んだ状態でｾﾝｻのﾗﾝﾌﾟが点灯する事",
"1mm",
"1mm"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "振動抑制ｼﾘﾝﾀﾞ組立3",
"WorkItems": [
"3. PHﾁｪｯｶで確認",
"2. 1完成品にSWITCH(450MM) を取付"
],
"WorkPoints": [
"縮んだ状態でｾﾝｻのﾗﾝﾌﾟが点灯する事",
"1mm",
"1mm"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "1㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ(共通)",
"Size": "",
"ToolOther": "FM-3418",
"WorkName": "振動抑制ｼﾘﾝﾀﾞ組立3",
"WorkItems": [
"3. PHﾁｪｯｶで確認",
"2. 1完成品にSWITCH(450MM) を取付"
],
"WorkPoints": [
"縮んだ状態でｾﾝｻのﾗﾝﾌﾟが点灯する事",
"1mm",
"1mm"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-3418",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りONする事",
"Method": "PHﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "振動抑制ｼﾘﾝﾀﾞ組立4",
"WorkItems": [
"2. 1完成品を②又は③に取付",
"1. TUBE を1本切る"
],
"WorkPoints": [
"･②又は③のｽﾘｰﾌﾞにﾁｭｰﾌﾞを通します｡･ﾁｭｰﾌﾞをゆっくりと継手に装着してく ださい｡ その際､ﾁｭｰﾌﾞ端とﾊﾞｰﾌﾞ端 との間に少し隙間(約0.5mm)が生じるよ うにします｡ 0.5mmのｼｯｸﾈｽｹﾞｰｼﾞを挟んで取付ける｡･ｽﾘｰﾌﾞをゆっくりと装着してください｡ その際､ｽﾘｰﾌﾞ端面とﾎﾞﾃﾞｨ端面との 間に隙間がないようにしてください(図 参照)｡ 【抵抗が強く､端面まで押せない場合】 ﾁｭｰﾌﾞがかみ込んでいる可能性があります｡隙間が確保されるよう十分ご注意いただいたうえ､ 再度や り直してください｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"TUBE ﾁｭｰﾌﾞ"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "360㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.50㎜",
"ToolOther": "",
"WorkName": "振動抑制ｼﾘﾝﾀﾞ組立4",
"WorkItems": [
"2. 1完成品を②又は③に取付",
"1. TUBE を1本切る"
],
"WorkPoints": [
"･②又は③のｽﾘｰﾌﾞにﾁｭｰﾌﾞを通します｡･ﾁｭｰﾌﾞをゆっくりと継手に装着してく ださい｡ その際､ﾁｭｰﾌﾞ端とﾊﾞｰﾌﾞ端 との間に少し隙間(約0.5mm)が生じるよ うにします｡ 0.5mmのｼｯｸﾈｽｹﾞｰｼﾞを挟んで取付ける｡･ｽﾘｰﾌﾞをゆっくりと装着してください｡ その際､ｽﾘｰﾌﾞ端面とﾎﾞﾃﾞｨ端面との 間に隙間がないようにしてください(図 参照)｡ 【抵抗が強く､端面まで押せない場合】 ﾁｭｰﾌﾞがかみ込んでいる可能性があります｡隙間が確保されるよう十分ご注意いただいたうえ､ 再度や り直してください｡"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"TUBE ﾁｭｰﾌﾞ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜を挟んで取付ける事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(延長ｺﾝﾍﾞﾔｰ)",
"Size": "",
"ToolOther": "FM-6620",
"WorkName": "延長ｺﾝﾍﾞﾔｶﾊﾞｰ組立1",
"WorkItems": [
"1. ①に⑥を貼付ける"
],
"WorkPoints": [
"⑥を㉗に青色矢印方向に合わせて貼付け",
"貼付前に㉖にて貼付部分を清掃する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-6620",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｶﾊﾞｰ組立2",
"WorkItems": [
"1. COVER にPLATE をNUT-PLATE SCREW で仮取付",
"2. 1完成品にBRACKET をNUT-PLATE BOLT WASHER で仮取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"仮止め:H1工程にて本締め",
"仮止め:H1工程にて本締め",
"削除"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｶﾊﾞｰ組立3",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｶﾊﾞｰ組立4",
"WorkItems": [
"1. ①にSPACER をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｶﾊﾞｰ組立5",
"WorkItems": [
"1. ①に②を③で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｶﾊﾞｰ組立5",
"WorkItems": [
"1. ①に②を③で取付",
"2. 1完成品に⑥を貼付"
],
"WorkPoints": [
"①に㉙をピンク色矢印方向に当てつける",
"⑥を㉙の青色矢印方向に合わせて貼付け",
"貼付前に㉘にて貼付部分を清掃する事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｵﾚﾝｼﾞ色矢視断面",
"㉙コネクタラベル"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(延長ｺﾝﾍﾞﾔｰ)",
"Size": "",
"ToolOther": "FM-6620",
"WorkName": "延長ｺﾝﾍﾞﾔｶﾊﾞｰ組立5",
"WorkItems": [
"2. 1完成品に⑥を貼付"
],
"WorkPoints": [
"①に㉙をピンク色矢印方向に当てつける",
"⑥を㉙の青色矢印方向に合わせて貼付け",
"貼付前に㉘にて貼付部分を清掃する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｵﾚﾝｼﾞ色矢視断面",
"㉙コネクタラベル"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "FM-6620",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｶﾊﾞｰ組立6",
"WorkItems": [
"1. ①にCONNECTOR をBOLT で取付ける"
],
"WorkPoints": [
"MOLEX",
"MOLEX",
"MOLEX表示"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｶﾊﾞｰ組立7",
"WorkItems": [
"1. ①にCABLE CABLE を差込む"
],
"WorkPoints": [
"1B1900L/R",
"1B1900R/L",
"B1900/1P",
"B1900/1TP"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｶﾊﾞｰ組立8",
"WorkItems": [
"1. ①にCABLE CABLE を接続し固定する"
],
"WorkPoints": [
"CNEXR/",
"CNEXL/",
"CNEXR/",
"CNEXL/",
"1B1900R",
"1B1900L",
"1B1900R",
"1B1900L",
"下記は左側延長用",
"下記は右側延長用"
],
"Tolks": [],
"InspectionNo": "WETE-G002-C08",
"InspectionItems": [
"検査表①:接続確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WETE-G002-C08"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C08",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.