Datasets:
ayuzawa
/
ManageProcess21

Dataset card Data Studio Files
xet
Community
1
input
stringclasses
1 value
instruction
stringlengths
223
3.4k
output
stringlengths
206
380
category
stringclasses
1 value
index
stringclasses
1 value
fileName
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾉｽﾞﾙ交換動作ﾃｽﾄ2", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "回数表示", "1. ①を押して前後にする", "3. を押しながら③を押す", "5. 動作停止後④を押し画像をSDｶｰﾄﾞに保存する", "検査表①:6.ﾉｽﾞﾙ交換動作確認", "ｴﾗｰ無き事", "2. を押しながら②を押す", "4. 回数が4以上になったらSTOPﾎﾞﾀﾝを押す", "2ﾋﾞｰﾑ仕様時は､⑤を押しRearに切り替えてから⑥を押し画像保存する事", "WEAV-G002-A04" ] }
{ "QualityItem": "表示確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ｴﾗｰ無き事", "Method": "目視", "RecordMethod": "WEAV-G002-A04", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾗｲﾝSWBOX", "Size": "", "ToolOther": "FM-2460", "WorkName": "基板搬送確認1", "WorkItems": [ "2. ①を押す", "3. ②を押す", "6. ﾚｰﾝ2も同様手順で実施する", "1. ㉖を接続する", "4. ③を押す", "5. 基板ｻｲｽﾞに合ったﾃﾞｰﾀを選択し､④を押す" ], "WorkPoints": [ "仕様により接続位置が違うので注意する", "ﾃﾞｰﾀ選択", "ﾚｰﾝ2はﾃﾞｭｱﾙﾓｰﾄﾞ仕様時のみ実施", "ﾚｰﾝ切替" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "[本体] [SWBOX] XL - XS", "■右→左流れ時", "[本体] [SWBOX] XR - XS", "■左→右流れ時" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "FM-2460", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "基板搬送確認2", "WorkItems": [ "1. ①②を押す", "3. 『10』と入力しENTを押す", "2. ③を押し『ON』にした後､④を押す", "4. ④を押す", "5. 『10』と入力しENTを押す", "6. ④を押す" ], "WorkPoints": [ "ｼﾝｸﾞﾙｺﾝﾍﾞｱの場合､6へ" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "入力確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "搬送確認基板(50×50)搬送確認基板(510×590)搬送確認基板(300×260)", "Size": "", "ToolOther": "FM-2142N210141058AAMTPZ000672AA", "WorkName": "基板搬送確認3", "WorkItems": [ "1. ①を押す", "2. ②を押す", "3. ③を押す", "4. を押しながらｽﾀｰﾄ SWを押す", "5. ④を押す", "6. 搬入待ちになったら基板を搬入する" ], "WorkPoints": [ "ｼﾝｸﾞﾙｺﾝﾍﾞｱはﾚｰﾝ1のみ", "ｼﾝｸﾞﾙｺﾝﾍﾞｱはﾚｰﾝ1のみ表示" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-2142N210141058AAMTPZ000672AA", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ｴﾗｰ無き事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "搬送確認基板(50×50)搬送確認基板(510×590)搬送確認基板(300×260)", "Size": "", "ToolOther": "FM-2142N210141058AAMTPZ000672AA", "WorkName": "基板搬送確認3", "WorkItems": [ "1. ①を押す", "2. ②を押す", "3. ③を押す", "4. を押しながらｽﾀｰﾄ SWを押す", "5. ④を押す", "6. 搬入待ちになったら基板を搬入する" ], "WorkPoints": [ "ｼﾝｸﾞﾙｺﾝﾍﾞｱはﾚｰﾝ1のみ", "ｼﾝｸﾞﾙｺﾝﾍﾞｱはﾚｰﾝ1のみ表示" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-2142N210141058AAMTPZ000672AA", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ｴﾗｰ無き事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "搬送確認基板(50×50)搬送確認基板(510×590)搬送確認基板(300×260)", "Size": "", "ToolOther": "FM-2142N210141058AAMTPZ000672AA", "WorkName": "基板搬送確認3", "WorkItems": [ "1. ①を押す", "2. ②を押す", "3. ③を押す", "4. を押しながらｽﾀｰﾄ SWを押す", "5. ④を押す", "6. 搬入待ちになったら基板を搬入する" ], "WorkPoints": [ "ｼﾝｸﾞﾙｺﾝﾍﾞｱはﾚｰﾝ1のみ", "ｼﾝｸﾞﾙｺﾝﾍﾞｱはﾚｰﾝ1のみ表示" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-2142N210141058AAMTPZ000672AA", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ｴﾗｰ無き事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "搬送確認基板(50×50)搬送確認基板(510×590)搬送確認基板(300×260)", "Size": "", "ToolOther": "FM-2142N210141058AAMTPZ000672AA", "WorkName": "基板搬送確認4", "WorkItems": [ "1. 搬出待ちになったら基板を搬出する", "2. 搬出後搬入待ちになるので5枚流すまで､搬入･搬出を繰り返す" ], "WorkPoints": [ "基板搬出方法(ﾃﾞｭｱﾙﾓｰﾄﾞの場合)", "基板搬出方法(ｼﾝｸﾞﾙﾓｰﾄﾞの場合)", "ｼﾝｸﾞﾙｺﾝﾍﾞｱはﾚｰﾝ1のみ" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "基板が完全に搬出されたらSR.RDYをOFFする", "基板が完全に搬出されたらMR.RDYをOFFする", "ﾚｰﾝ1が搬出待ちになったらMR.RDYをONする", "ﾚｰﾝ2が搬出待ちになったらSR.RDYをONする", "基板が完全に搬出されたらMR.RDYをOFFする", "搬出待ちになったらMR.RDYをONする" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-2142N210141058AAMTPZ000672AA", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ｴﾗｰ無き事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "搬送確認基板(50×50)搬送確認基板(510×590)搬送確認基板(300×260)", "Size": "", "ToolOther": "FM-2142N210141058AAMTPZ000672AA", "WorkName": "基板搬送確認4", "WorkItems": [ "1. 搬出待ちになったら基板を搬出する", "2. 搬出後搬入待ちになるので5枚流すまで､搬入･搬出を繰り返す" ], "WorkPoints": [ "基板搬出方法(ﾃﾞｭｱﾙﾓｰﾄﾞの場合)", "基板搬出方法(ｼﾝｸﾞﾙﾓｰﾄﾞの場合)", "ｼﾝｸﾞﾙｺﾝﾍﾞｱはﾚｰﾝ1のみ" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "基板が完全に搬出されたらSR.RDYをOFFする", "基板が完全に搬出されたらMR.RDYをOFFする", "ﾚｰﾝ1が搬出待ちになったらMR.RDYをONする", "ﾚｰﾝ2が搬出待ちになったらSR.RDYをONする", "基板が完全に搬出されたらMR.RDYをOFFする", "搬出待ちになったらMR.RDYをONする" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-2142N210141058AAMTPZ000672AA", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ｴﾗｰ無き事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "搬送確認基板(50×50)搬送確認基板(510×590)搬送確認基板(300×260)", "Size": "", "ToolOther": "FM-2142N210141058AAMTPZ000672AA", "WorkName": "基板搬送確認4", "WorkItems": [ "1. 搬出待ちになったら基板を搬出する", "2. 搬出後搬入待ちになるので5枚流すまで､搬入･搬出を繰り返す" ], "WorkPoints": [ "基板搬出方法(ﾃﾞｭｱﾙﾓｰﾄﾞの場合)", "基板搬出方法(ｼﾝｸﾞﾙﾓｰﾄﾞの場合)", "ｼﾝｸﾞﾙｺﾝﾍﾞｱはﾚｰﾝ1のみ" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "基板が完全に搬出されたらSR.RDYをOFFする", "基板が完全に搬出されたらMR.RDYをOFFする", "ﾚｰﾝ1が搬出待ちになったらMR.RDYをONする", "ﾚｰﾝ2が搬出待ちになったらSR.RDYをONする", "基板が完全に搬出されたらMR.RDYをOFFする", "搬出待ちになったらMR.RDYをONする" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-2142N210141058AAMTPZ000672AA", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ｴﾗｰ無き事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "搬送確認基板(50×50)搬送確認基板(510×590)搬送確認基板(300×260)", "Size": "", "ToolOther": "FM-2142N210141058AAMTPZ000672AA", "WorkName": "基板搬送確認4", "WorkItems": [ "1. 搬出待ちになったら基板を搬出する", "2. 搬出後搬入待ちになるので5枚流すまで､搬入･搬出を繰り返す" ], "WorkPoints": [ "基板搬出方法(ﾃﾞｭｱﾙﾓｰﾄﾞの場合)", "基板搬出方法(ｼﾝｸﾞﾙﾓｰﾄﾞの場合)", "ｼﾝｸﾞﾙｺﾝﾍﾞｱはﾚｰﾝ1のみ" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "基板が完全に搬出されたらSR.RDYをOFFする", "基板が完全に搬出されたらMR.RDYをOFFする", "ﾚｰﾝ1が搬出待ちになったらMR.RDYをONする", "ﾚｰﾝ2が搬出待ちになったらSR.RDYをONする", "基板が完全に搬出されたらMR.RDYをOFFする", "搬出待ちになったらMR.RDYをONする" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-2142N210141058AAMTPZ000672AA", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ｴﾗｰ無き事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "搬送確認基板(50×50)搬送確認基板(510×590)搬送確認基板(300×260)", "Size": "", "ToolOther": "FM-2142N210141058AAMTPZ000672AA", "WorkName": "基板搬送確認5", "WorkItems": [ "1. ①を押す", "2. ②を押し画像を保存し､③を押す", "3. ④を押し画像を保存する", "4. ﾃﾞｭｱﾙﾓｰﾄﾞ時のみ⑤を押した後､⑥を押し画像を保存する", "5. 各基板を同様の手順で実施する", "6. 搬送確認後は⑦生産予定枚数を『0』にして⑧を『OFF』にする" ], "WorkPoints": [ "基板ﾃﾞｰﾀ保存", "ﾚｰﾝ1稼働情報保存", "ﾚｰﾝ2稼働情報保存", "ﾚｰﾝ切替はﾃﾞｭｱﾙﾓｰﾄﾞ時のみ実施", "基板が正常に搬送する事" ], "Tolks": [], "InspectionNo": "WEAV-G002-A04", "InspectionItems": [ "検査表①:7.基板搬送確認" ], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "WEAV-G002-A04" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-2142N210141058AAMTPZ000672AA", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ｴﾗｰ無き事", "Method": "目視", "RecordMethod": "WEAV-G002-A04", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "搬送確認基板(50×50)搬送確認基板(510×590)搬送確認基板(300×260)", "Size": "", "ToolOther": "FM-2142N210141058AAMTPZ000672AA", "WorkName": "基板搬送確認5", "WorkItems": [ "1. ①を押す", "2. ②を押し画像を保存し､③を押す", "3. ④を押し画像を保存する", "4. ﾃﾞｭｱﾙﾓｰﾄﾞ時のみ⑤を押した後､⑥を押し画像を保存する", "5. 各基板を同様の手順で実施する", "6. 搬送確認後は⑦生産予定枚数を『0』にして⑧を『OFF』にする" ], "WorkPoints": [ "基板ﾃﾞｰﾀ保存", "ﾚｰﾝ1稼働情報保存", "ﾚｰﾝ2稼働情報保存", "ﾚｰﾝ切替はﾃﾞｭｱﾙﾓｰﾄﾞ時のみ実施", "基板が正常に搬送する事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "検査表①:7.基板搬送確認", "WEAV-G002-A04" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-2142N210141058AAMTPZ000672AA", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ｴﾗｰ無き事", "Method": "目視", "RecordMethod": "WEAV-G002-A04", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "搬送確認基板(50×50)搬送確認基板(510×590)搬送確認基板(300×260)", "Size": "", "ToolOther": "FM-2142N210141058AAMTPZ000672AA", "WorkName": "基板搬送確認5", "WorkItems": [ "1. ①を押す", "2. ②を押し画像を保存し､③を押す", "3. ④を押し画像を保存する", "4. ﾃﾞｭｱﾙﾓｰﾄﾞ時のみ⑤を押した後､⑥を押し画像を保存する", "5. 各基板を同様の手順で実施する", "6. 搬送確認後は⑦生産予定枚数を『0』にして⑧を『OFF』にする" ], "WorkPoints": [ "基板ﾃﾞｰﾀ保存", "ﾚｰﾝ1稼働情報保存", "ﾚｰﾝ2稼働情報保存", "ﾚｰﾝ切替はﾃﾞｭｱﾙﾓｰﾄﾞ時のみ実施", "基板が正常に搬送する事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "検査表①:7.基板搬送確認", "WEAV-G002-A04" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-2142N210141058AAMTPZ000672AA", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ｴﾗｰ無き事", "Method": "目視", "RecordMethod": "WEAV-G002-A04", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "搬送確認基板(50×50)搬送確認基板(510×590)搬送確認基板(300×260)", "Size": "", "ToolOther": "FM-2142N210141058AAMTPZ000672AA", "WorkName": "基板搬送確認5", "WorkItems": [ "1. ①を押す", "2. ②を押し画像を保存し､③を押す", "3. ④を押し画像を保存する", "4. ﾃﾞｭｱﾙﾓｰﾄﾞ時のみ⑤を押した後､⑥を押し画像を保存する", "5. 各基板を同様の手順で実施する", "6. 搬送確認後は⑦生産予定枚数を『0』にして⑧を『OFF』にする" ], "WorkPoints": [ "基板ﾃﾞｰﾀ保存", "ﾚｰﾝ1稼働情報保存", "ﾚｰﾝ2稼働情報保存", "ﾚｰﾝ切替はﾃﾞｭｱﾙﾓｰﾄﾞ時のみ実施", "基板が正常に搬送する事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "検査表①:7.基板搬送確認", "WEAV-G002-A04" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-2142N210141058AAMTPZ000672AA", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ｴﾗｰ無き事", "Method": "目視", "RecordMethod": "WEAV-G002-A04", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "81cN･m", "WorkName": "ﾁｬｰﾄﾏｰｸﾌﾞﾛｯｸ取付", "WorkItems": [ "1. 軽量16ﾉｽﾞﾙﾍｯﾄﾞV3Aに①をBOLT で取付" ], "WorkPoints": [ "面取りが右側", "前後に軽量16ﾉｽﾞﾙﾍｯﾄﾞV3Aがある場合はそれぞれ取付のこと" ], "Tolks": [ "締付ﾄﾙｸ 81cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "81cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｴｰｼﾞﾝｸﾞ動作1", "WorkItems": [ "1. ①②を順番通り押す", "2. ③を押す", "3. ④を押す", "4. ⑤⑥を順番通り押す", "5. ⑦⑧を順番通り押す", "6. ⑨自動生成できたか確認する" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "表示確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｴｰｼﾞﾝｸﾞ動作2", "WorkItems": [ "1. ①を押す", "2. ②を押す", "3. 下記の設定をOFFにした後､③を押す", "4. を押しながらSTART SWを押す", "5. を押しながら④を押す" ], "WorkPoints": [ "基板搬送･基板認識･吸着･部品認識･ﾃｰﾌﾟ送り･ﾉｽﾞﾙ認識･ﾘｶﾊﾞﾘ･転写をOFFにする自動ﾋﾟﾝ交換がある場合は下受けﾋﾟﾝOFFにする", "ｴｰｼﾞﾝｸﾞが開始される" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "設定確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｴｰｼﾞﾝｸﾞ動作3", "WorkItems": [ "1. STOP SWを押しｴｰｼﾞﾝｸﾞを停止させた後､①を押す", "2. を押しながら②を押す" ], "WorkPoints": [ "規定時間以上の稼働を確認する", "ｼﾝｸﾞﾙｺﾝﾍﾞｱはﾚｰﾝ1のみ表示" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "動作確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ｴﾗｰ無き事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "ﾊﾟﾚｯﾄ飛出しｾﾝｻ組立1", "WorkItems": [ "1. BRACKET にBRACKET をBOLT WASHER で取付ける", "2. 1完成品にSENSOR SENSOR をSCREW BOLT WASHER で取付ける" ], "WorkPoints": [ "投光側:ｺﾈｸﾀ名称_B1304TR" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "45cN･m", "WorkName": "ﾊﾟﾚｯﾄ飛出しｾﾝｻ組立1", "WorkItems": [], "WorkPoints": [ "面を合わせて取付ける", "投光側:ｺﾈｸﾀ名称_B1344TR", "受光側:ｺﾈｸﾀ名称_B1344R", "ｾﾝｻｰ付属品", "ｾﾝｻｰ付属品", "ｾﾝｻｰ付属品" ], "Tolks": [ "締付ﾄﾙｸ 45cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "45cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "ﾊﾟﾚｯﾄ飛出しｾﾝｻ組立2", "WorkItems": [ "1. BRACKET にBRACKET をBOLT WASHER で取付ける", "2. 1完成品に③をSCREW WASHER WASHER で取付ける" ], "WorkPoints": [ "受光側:ｺﾈｸﾀ名称_B1304R" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "45cN･m", "WorkName": "ﾊﾟﾚｯﾄ飛出しｾﾝｻ組立2", "WorkItems": [], "WorkPoints": [ "面を合わせて取付ける", "ｾﾝｻｰ付属品" ], "Tolks": [ "締付ﾄﾙｸ 45cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "45cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.1", "ToolOther": "90cN･m", "WorkName": "水準器組立", "WorkItems": [ "1. BLOCK にPRECISION-LEVEL をSCREW で取付ける", "2. 1完成品をBRACKET にBOLT WASHER WASHER で取付ける" ], "WorkPoints": [ "BLOCK とPRECISION-LEVEL の両端揃え", "同一の物を2個作製", "同一の物を2個作製" ], "Tolks": [ "締付ﾄﾙｸ 90cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "90cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "水準器組立", "WorkItems": [], "WorkPoints": [ "矢印方向へ押し当てて取付けの事", "1完成品の100\"/1DIVの表示をﾌﾞﾗｹｯﾄ側にする事" ], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "削除" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "7㎜", "ToolOther": "2.0N･m", "WorkName": "開閉ｱｰﾑ組立", "WorkItems": [ "1. LEVER にBOLT NUT ･⑱を取付ける" ], "WorkPoints": [ "11㎜", "取付け寸法:11㎜", "⑱はﾎﾞﾙﾄ先端が穴から出ない様挿入する", "各2個づつ作製する" ], "Tolks": [ "締付ﾄﾙｸ 2.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "2.0N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "開閉ｱｰﾑ組立", "WorkItems": [ "1. LEVER にBOLT NUT ･⑱を取付ける" ], "WorkPoints": [ "11㎜", "取付け寸法:11㎜", "⑱はﾎﾞﾙﾄ先端が穴から出ない様挿入する", "各2個づつ作製する" ], "Tolks": [ "締付ﾄﾙｸ 2.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.1", "ToolOther": "194cN･m", "WorkName": "ﾊﾟﾚｯﾄ飛出し防止ｼﾘﾝﾀﾞｰ組立1", "WorkItems": [ "1. CYLINDER CYLINDER CYLINDER CYLINDER にBRACKET をBOLT WASHER で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "◆作業者安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "ｸﾞﾘｰｽLCG100", "WorkName": "ﾊﾟﾚｯﾄ飛出し防止ｼﾘﾝﾀﾞｰ組立1", "WorkItems": [ "◆2. COLLAR にｸﾞﾘ-ｽを塗布し､1の完成品にCOLLAR BRACKET をNUT で取付ける" ], "WorkPoints": [ "付属のﾅｯﾄは廃棄する", "ｼｬﾌﾄ先端の面に合わせる事", "ｸﾞﾘ-ｽは外周に塗布する事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:1", "◆作業者安全作業" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:1", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "ｸﾞﾘｰｽLCG100", "WorkName": "ﾊﾟﾚｯﾄ飛出し防止ｼﾘﾝﾀﾞｰ組立2", "WorkItems": [ "▲1. COLLAR にｸﾞﾘｰｽを塗布する", "◆2. ②③に④⑤をCOLLAR BOLT で取付ける" ], "WorkPoints": [ "ｸﾞﾘｰｽ塗布位置", "ﾚﾊﾞｰとﾌﾞﾗｹｯﾄの間にｸﾞﾘｰｽを塗布の事" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:各1", "◆作業者安全作業", "ｸﾞﾘｰｽ塗布 米粒:各1" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "95cN･m", "WorkName": "ﾊﾟﾚｯﾄ飛出し防止ｼﾘﾝﾀﾞｰ組立2", "WorkItems": [ "▲1. COLLAR にｸﾞﾘｰｽを塗布する", "◆2. ②③に④⑤をCOLLAR BOLT で取付ける" ], "WorkPoints": [ "ﾚﾊﾞｰとﾌﾞﾗｹｯﾄの間にｸﾞﾘｰｽを塗布の事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "◆作業者安全作業", "●クリーン作業" ], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:各1", "◆作業者安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程", "特殊工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立1", "WorkItems": [ "1. BRACKET にLABEL を貼付ける", "2. 1完成品にSPACER をBOLT WASHER で取付ける", "3. 2完成品にSPACER をBOLT NUT で取付ける" ], "WorkPoints": [ "2㎜", "5㎜", "5㎜", "2㎜", "24㎜", "30㎜", "6㎜", "27㎜", "54㎜" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 2.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立1", "WorkItems": [ "2. 1完成品にSPACER をBOLT WASHER で取付ける", "1. BRACKET にLABEL を貼付ける", "3. 2完成品にSPACER をBOLT NUT で取付ける" ], "WorkPoints": [ "24㎜", "2㎜", "5㎜", "30㎜", "5㎜", "2㎜", "6㎜", "27㎜", "54㎜" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 2.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "7㎜", "ToolOther": "2.0N･m", "WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立1", "WorkItems": [], "WorkPoints": [ "30㎜", "6㎜", "27㎜", "54㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "2.0N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "ｸﾞﾘｰｽLCG100", "WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立2", "WorkItems": [], "WorkPoints": [ "ｸﾞﾘ-ｽ塗布位置", "接触面にｸﾞﾘ-ｽ塗布", "ｸﾞﾘ-ｽ塗布位置", "接触面にｸﾞﾘ-ｽ塗布" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m", "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:各1", "◆作業者安全作業", "ｸﾞﾘｰｽ塗布 米粒:各1" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立2", "WorkItems": [], "WorkPoints": [ "ｸﾞﾘ-ｽ塗布位置", "接触面にｸﾞﾘ-ｽ塗布" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:各1", "◆作業者安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立3", "WorkItems": [ "◆2. 1完成品にSTOPPER をBOLT で取付ける", "1. ①にSPACER BEARING をBOLT で取付ける", "◆2. 1完成品にSTOPPER をBOLT で取付ける", "1. ①にSPACER BEARING をBOLT で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:各1", "◆作業者安全作業", "ｸﾞﾘｰｽ塗布 米粒:各1" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "ｸﾞﾘｰｽLCG100", "WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立3", "WorkItems": [ "◆2. 1完成品にSTOPPER をBOLT で取付ける", "1. ①にSPACER BEARING をBOLT で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:各1", "◆作業者安全作業" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立4", "WorkItems": [ "1. ①にBRACKET BRACKET をBOLT WASHER で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立4", "WorkItems": [ "2. 1完成品に④をBOLT WASHER で取付け後､CABLE-SUPPORT を取付ける" ], "WorkPoints": [ "B1304TR" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "PHﾁｪｯｶｰ", "Size": "", "ToolOther": "", "WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立5", "WorkItems": [ "1. ①に②③を取付け検出動作を確認する" ], "WorkPoints": [ "上側:B1320R", "上側:B1322R", "下側:B1321R", "下側:B1323R", "取付け寸法:22㎜", "取付け寸法:9㎜", "取付け寸法:22㎜", "取付け寸法:9㎜", "B1322R･B1320Rｾﾝｻ確認時ｼﾘﾝﾀﾞ位置", "B1323R･B1321Rｾﾝｻ確認時ｼﾘﾝﾀﾞ位置" ], "Tolks": [ "締付ﾄﾙｸ 10cN･m" ], "InspectionNo": "WEMA-G002-C11", "InspectionItems": [ "検査表①:4.ｼｬｯﾀｰ部L.S.調整" ], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "WEMA-G002-C11" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "開閉限位置でONする事", "Method": "PHﾁｪｯｶｰ", "RecordMethod": "WEMA-G002-C11", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "精密ﾏｲﾅｽ", "ToolOther": "10cN･m", "WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立5", "WorkItems": [ "1. ①に②③を取付け検出動作を確認する" ], "WorkPoints": [ "上側:B1320R", "上側:B1322R", "下側:B1321R", "下側:B1323R", "取付け寸法:22㎜", "取付け寸法:9㎜", "取付け寸法:22㎜", "取付け寸法:9㎜", "B1322R･B1320Rｾﾝｻ確認時ｼﾘﾝﾀﾞ位置", "B1323R･B1321Rｾﾝｻ確認時ｼﾘﾝﾀﾞ位置" ], "Tolks": [ "締付ﾄﾙｸ 10cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "検査表①:4.ｼｬｯﾀｰ部L.S.調整" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "10cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立5", "WorkItems": [ "1. ①に②③を取付け検出動作を確認する" ], "WorkPoints": [ "上側:B1320R", "上側:B1322R", "下側:B1321R", "下側:B1323R", "取付け寸法:22㎜", "取付け寸法:9㎜", "取付け寸法:22㎜", "取付け寸法:9㎜", "B1322R･B1320Rｾﾝｻ確認時ｼﾘﾝﾀﾞ位置", "B1323R･B1321Rｾﾝｻ確認時ｼﾘﾝﾀﾞ位置" ], "Tolks": [ "締付ﾄﾙｸ 10cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "検査表①:4.ｼｬｯﾀｰ部L.S.調整" ] }
{ "QualityItem": "位置確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "ｸﾞﾘｰｽLCG100", "WorkName": "ﾏｶﾞｼﾞﾝ側上面ﾌﾟﾚｰﾄ組立6", "WorkItems": [ "1. ①の配線を固定する", "◆2. 1完成品にSPRING を取付ける" ], "WorkPoints": [ "ﾊﾞﾈとﾎﾞﾙﾄの接触部に塗布する(左右2ヶ所行う事)", "B1320･B1321R", "B1304TR", "B1322R", "B1323R(一番長く)" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:各1", "◆作業者安全作業" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立1", "WorkItems": [ "1. BRACKET にLABEL を貼付ける", "2. 1完成品ににSPACER をBOLT WASHER で取付ける", "1. BRACKET にLABEL を貼付ける", "2. 1完成品ににSPACER をBOLT WASHER で取付ける" ], "WorkPoints": [ "18㎜", "5㎜", "40㎜", "18㎜", "5㎜", "40㎜", "18㎜", "5㎜", "40㎜", "18㎜", "5㎜", "40㎜" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立1", "WorkItems": [], "WorkPoints": [ "24㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "7㎜", "ToolOther": "2.0N･m", "WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立1", "WorkItems": [], "WorkPoints": [ "24㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "2.0N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "ｸﾞﾘｰｽLCG100", "WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立2", "WorkItems": [ "◆1. COLLAR にｸﾞﾘ-ｽを塗布する", "◆2. ①に②③をCOLLAR COLLAR BOLT で取付ける", "◆1. COLLAR にｸﾞﾘ-ｽを塗布する", "◆2. ①に②③をCOLLAR COLLAR BOLT で取付ける" ], "WorkPoints": [ "ｸﾞﾘ-ｽ塗布位置", "ｸﾞﾘ-ｽ塗布位置" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m", "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:各1", "ｸﾞﾘｰｽ塗布 米粒:各1", "◆作業者安全作業", "ｸﾞﾘｰｽ塗布 米粒:各1", "ｸﾞﾘｰｽ塗布 米粒:各1" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立2", "WorkItems": [ "◆1. COLLAR にｸﾞﾘ-ｽを塗布する", "◆2. ①に②③をCOLLAR COLLAR BOLT で取付ける" ], "WorkPoints": [ "ｸﾞﾘ-ｽ塗布位置" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:各1", "ｸﾞﾘｰｽ塗布 米粒:各1", "◆作業者安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立3", "WorkItems": [ "◆2. 1完成品にSTOPPER をBOLT で取付ける", "1. ①にSPACER BEARING をBOLT で取付ける", "◆2. 1完成品にSTOPPER をBOLT で取付ける", "1. ①にSPACER BEARING をBOLT で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業", "◆作業者安全作業" ], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:各1", "◆作業者安全作業", "ｸﾞﾘｰｽ塗布 米粒:各1" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "ｸﾞﾘｰｽLCG100", "WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立3", "WorkItems": [ "◆2. 1完成品にSTOPPER をBOLT で取付ける", "1. ①にSPACER BEARING をBOLT で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:各1", "◆作業者安全作業" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立4", "WorkItems": [ "1. ①にBRACKET BRACKET をBOLT WASHER で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立4", "WorkItems": [ "2. 1完成品に④をBOLT WASHER で取付け後､CABLE-SUPPORT を取付ける" ], "WorkPoints": [ "B1344TR" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "", "ToolOther": "", "WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立5", "WorkItems": [ "◆1. ①にSPRING を取付ける" ], "WorkPoints": [ "ﾊﾞﾈとﾎﾞﾙﾄの接触部に塗布する(左右2ヶ所行う事)" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "ｸﾞﾘｰｽ塗布 豆粒:各1" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "ｸﾞﾘｰｽLCG100", "WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立5", "WorkItems": [ "◆1. ①にSPRING を取付ける" ], "WorkPoints": [ "ﾊﾞﾈとﾎﾞﾙﾄの接触部に塗布する(左右2ヶ所行う事)" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "ｸﾞﾘｰｽ塗布 豆粒:各1", "◆作業者安全作業" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布豆粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "PHﾁｪｯｶｰ", "Size": "", "ToolOther": "", "WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立6", "WorkItems": [ "1. ①に②③を取付け検出動作を確認する" ], "WorkPoints": [ "下側:B1341T", "上側:B1340T", "上側:B1340", "下側:B1341", "取付け寸法:19㎜", "取付け寸法:19㎜", "B1341･B1341Tｾﾝｻ確認時ｼﾘﾝﾀﾞ-位置", "B1340･B1340Tｾﾝｻ確認時ｼﾘﾝﾀﾞ-位置", "取付け寸法:14㎜", "取付け寸法:14㎜" ], "Tolks": [ "締付ﾄﾙｸ 10cN･m" ], "InspectionNo": "WEMA-G002-C11", "InspectionItems": [ "検査表①:ｼｬｯﾀｰ部L.S.調整" ], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "WEMA-G002-C11" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "開閉限位置でONする事", "Method": "PHﾁｪｯｶｰ", "RecordMethod": "WEMA-G002-C11", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "精密ﾏｲﾅｽ", "ToolOther": "10cN･m", "WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立6", "WorkItems": [ "1. ①に②③を取付け検出動作を確認する" ], "WorkPoints": [ "下側:B1341T", "上側:B1340T", "上側:B1340", "下側:B1341", "取付け寸法:19㎜", "取付け寸法:19㎜", "B1341･B1341Tｾﾝｻ確認時ｼﾘﾝﾀﾞ-位置", "B1340･B1340Tｾﾝｻ確認時ｼﾘﾝﾀﾞ-位置", "取付け寸法:14㎜", "取付け寸法:14㎜" ], "Tolks": [ "締付ﾄﾙｸ 10cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "検査表①:ｼｬｯﾀｰ部L.S.調整" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "10cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立6", "WorkItems": [ "1. ①に②③を取付け検出動作を確認する" ], "WorkPoints": [ "下側:B1341T", "上側:B1340T", "上側:B1340", "下側:B1341", "取付け寸法:19㎜", "取付け寸法:19㎜", "B1341･B1341Tｾﾝｻ確認時ｼﾘﾝﾀﾞ-位置", "B1340･B1340Tｾﾝｻ確認時ｼﾘﾝﾀﾞ-位置", "取付け寸法:14㎜", "取付け寸法:14㎜" ], "Tolks": [ "締付ﾄﾙｸ 10cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "検査表①:ｼｬｯﾀｰ部L.S.調整" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立7", "WorkItems": [ "1. ①にCABLE を引き回し配線を固定する", "■2. 1完成品のｾﾝｻｰﾗﾍﾞﾙを固定する" ], "WorkPoints": [ "B1341TR", "B1340TR", "B1344TR", "B1341R", "B1340R", "ﾗﾍﾞﾙが正面から見えるように固定する", "7㎜" ], "Tolks": [], "InspectionNo": "WEMA-G002-D06", "InspectionItems": [ "検査表①:3.接続確認" ], "WorkTypes": [ "■安全作業", "◆作業者安全作業" ], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "ｲﾝｼｭﾛｯｸにより､ﾗﾍﾞﾙを配線に固定する", "･ｲﾝｼｭﾛｯｸによる固定方法", "検査表CABLE :ｾﾝｻｰﾗﾍﾞﾙ確認", "WEMA-G002-D06" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続できている事", "Method": "目視", "RecordMethod": "WEMA-G002-D06", "Other": "-", "ProcessNames": [ "作業者安全工程", "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立7", "WorkItems": [ "1. ①にCABLE を引き回し配線を固定する", "■2. 1完成品のｾﾝｻｰﾗﾍﾞﾙを固定する" ], "WorkPoints": [ "B1341TR", "B1340TR", "B1344TR", "B1341R", "B1340R", "ﾗﾍﾞﾙが正面から見えるように固定する", "7㎜" ], "Tolks": [], "InspectionNo": "WEMA-G002-C11", "InspectionItems": [ "検査表CABLE :ｾﾝｻｰﾗﾍﾞﾙ確認" ], "WorkTypes": [ "■安全作業" ], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "検査表①:3.接続確認", "ｲﾝｼｭﾛｯｸにより､ﾗﾍﾞﾙを配線に固定する", "･ｲﾝｼｭﾛｯｸによる固定方法", "WEMA-G002-C11" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "ﾗﾍﾞﾙが正面から見えるように固定する事", "Method": "目視", "RecordMethod": "WEMA-G002-C11", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｽﾄｯｶｰ側上面ﾌﾟﾚｰﾄ組立7", "WorkItems": [ "1. ①にCABLE を引き回し配線を固定する", "■2. 1完成品のｾﾝｻｰﾗﾍﾞﾙを固定する" ], "WorkPoints": [ "B1341TR", "B1340TR", "ﾗﾍﾞﾙが正面から見えるように固定する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "検査表①:3.接続確認", "ｲﾝｼｭﾛｯｸにより､ﾗﾍﾞﾙを配線に固定する", "･ｲﾝｼｭﾛｯｸによる固定方法", "検査表CABLE :ｾﾝｻｰﾗﾍﾞﾙ確認", "■安全作業" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "7㎜", "ToolOther": "2.0N･m", "WorkName": "ｼｬｯﾀｰ部前組み", "WorkItems": [ "1. LEVER にSPACER をBOLT NUT で取付ける" ], "WorkPoints": [ "BOLT はﾎﾞﾙﾄ先端が穴から出ないよう挿入する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "2.0N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｼｬｯﾀｰ部前組み", "WorkItems": [ "1. LEVER にSPACER をBOLT NUT で取付ける" ], "WorkPoints": [ "BOLT はﾎﾞﾙﾄ先端が穴から出ないよう挿入する" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "ｼｬｯﾀｰ部前組み", "WorkItems": [ "2. 1完成品をBRACKET BRACKET にBEARING BOLT WASHER で取付ける", "3. 2完成品にSTOPPER をBOLT で取付ける" ], "WorkPoints": [ "18.5㎜", "ｽﾄｯﾊﾟｰｾﾝﾀｰﾗｲﾝとﾚﾊﾞｰ端面を平行にして取付けの事" ], "Tolks": [ "締付ﾄﾙｸ 3.2N･m", "締付ﾄﾙｸ 3.2N･m", "締付ﾄﾙｸ 2.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "銘板貼付け1", "WorkItems": [ "1. GUIDE にLABEL を､GUIDE にLABEL を貼付ける" ], "WorkPoints": [ "反対面も同様に貼付けの事", "1㎜", "1㎜", "1㎜", "2㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾊﾟﾚｯﾄｽﾄｯｸ部ｶﾞｲﾄﾞ組立ｼﾞｸﾞ", "Size": "", "ToolOther": "FM-5945", "WorkName": "ﾌﾚｰﾑ組立1", "WorkItems": [ "1. PLATE を治具に取付ける", "2. 1完成品に治具を取付ける" ], "WorkPoints": [ "取付穴を合わせる事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-5945", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付けできている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ﾌﾚｰﾑ組立2", "WorkItems": [ "2. 1完成品を締結する" ], "WorkPoints": [ "矢印方向に押し当て取付けの事", "A矢視", "B矢視", "0.05㎜が通ら無い事", "0.05㎜が通ら無い事" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [ "検査表①:1.ｽﾄｯｸ部ﾌﾚｰﾑ組立治具" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.05㎜", "ToolOther": "", "WorkName": "ﾌﾚｰﾑ組立2", "WorkItems": [ "2. 1完成品を締結する" ], "WorkPoints": [ "矢印方向に押し当て取付けの事", "A矢視", "B矢視", "0.05㎜が通ら無い事", "0.05㎜が通ら無い事" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "WEMA-G002-C11", "InspectionItems": [ "検査表①:1.ｽﾄｯｸ部ﾌﾚｰﾑ組立治具" ], "WorkTypes": [ "■安全作業" ], "Words": [ "WEMA-G002-C11" ] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "基準側:0.05㎜が通ら無い事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "WEMA-G002-C11", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.05㎜", "ToolOther": "", "WorkName": "ﾌﾚｰﾑ組立2", "WorkItems": [ "2. 1完成品を締結する" ], "WorkPoints": [ "矢印方向に押し当て取付けの事", "A矢視", "B矢視", "0.05㎜が通ら無い事", "0.05㎜が通ら無い事" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [ "検査表①:1.ｽﾄｯｸ部ﾌﾚｰﾑ組立治具", "WEMA-G002-C11" ] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "反基準側:0.15㎜が通ら無い事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "WEMA-G002-C11", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾊﾟﾚｯﾄｽﾄｯｸ部ｶﾞｲﾄﾞ組立ｼﾞｸﾞ", "Size": "", "ToolOther": "FM-5945", "WorkName": "ﾌﾚｰﾑ組立2", "WorkItems": [ "1. ①にPLATE をBOLT WASHER で仮取付けする", "2. 1完成品を締結する" ], "WorkPoints": [ "ｼﾞｸﾞ付属ﾎﾞﾙﾄ", "ｼﾞｸﾞ付属ﾎﾞﾙﾄ", "左右共ﾋﾟﾝｹﾞｰｼﾞで位置決めする", "矢印方向に押し当て取付けの事", "A矢視", "B矢視", "0.05㎜が通ら無い事", "0.05㎜が通ら無い事" ], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [ "検査表①:1.ｽﾄｯｸ部ﾌﾚｰﾑ組立治具" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-5945", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付けできている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "4.5", "ToolOther": "3.0cN･m", "WorkName": "ﾌﾚｰﾑ組立3", "WorkItems": [ "5. 反対側も同様の手順で取付ける" ], "WorkPoints": [ "矢印方向に押し当て取付けの事", "ﾄﾙｸ締結後ｾｯﾄﾋﾞｽで固定する", "締結後､治具を取り外す事", "ﾛｰﾚｯﾄを締め付け固定する" ], "Tolks": [ "締付ﾄﾙｸ 70cN･m" ], "InspectionNo": "WEMA-G002-C11", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.0cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "70cN･m", "WorkName": "ﾌﾚｰﾑ組立3", "WorkItems": [ "4. 3完成品をSCREW WASHER で取付ける", "5. 反対側も同様の手順で取付ける" ], "WorkPoints": [ "0.1㎜が通ら無い事", "ﾛｰﾚｯﾄを締め付け固定する" ], "Tolks": [ "締付ﾄﾙｸ 70cN･m", "締付ﾄﾙｸ 70cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [ "検査表①:2.ｽﾄｯｸ部樹脂ﾗｯｸ取付前後方向ｼﾞｸﾞ隙間確認" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "70cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.1㎜", "ToolOther": "", "WorkName": "ﾌﾚｰﾑ組立3", "WorkItems": [ "4. 3完成品をSCREW WASHER で取付ける" ], "WorkPoints": [ "0.1㎜が通ら無い事" ], "Tolks": [ "締付ﾄﾙｸ 70cN･m" ], "InspectionNo": "WEMA-G002-C11", "InspectionItems": [ "検査表①:2.ｽﾄｯｸ部樹脂ﾗｯｸ取付前後方向ｼﾞｸﾞ隙間確認" ], "WorkTypes": [ "■安全作業" ], "Words": [ "WEMA-G002-C11" ] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.1㎜が通ら無い事", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "WEMA-G002-C11", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾊﾟﾚｯﾄｽﾄｯｸ部ｶﾞｲﾄﾞ組立ｼﾞｸﾞ", "Size": "", "ToolOther": "FM-5945", "WorkName": "ﾌﾚｰﾑ組立3", "WorkItems": [ "3. 2完成品の偏芯PINを回してﾌﾟﾚｰﾄを挟み込む", "2. ①に②③GUIDE を挿入する", "3. 2完成品にｼﾞｸﾞを取付けﾌﾟﾚｰﾄを固定する", "4. 3完成品をSCREW WASHER で取付ける", "5. 反対側も同様の手順で取付ける" ], "WorkPoints": [ "矢印方向に押し当て取付けの事", "ﾄﾙｸ締結後ｾｯﾄﾋﾞｽで固定する", "締結後､治具を取り外す事", "0.1㎜が通ら無い事", "ﾛｰﾚｯﾄを締め付け固定する" ], "Tolks": [ "締付ﾄﾙｸ 3.0cN･m", "締付ﾄﾙｸ 3.0cN･m", "締付ﾄﾙｸ 70cN･m", "締付ﾄﾙｸ 70cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [ "検査表①:2.ｽﾄｯｸ部樹脂ﾗｯｸ取付高さ方向ｼﾞｸﾞ隙間確認", "検査表①:2.ｽﾄｯｸ部樹脂ﾗｯｸ取付前後方向ｼﾞｸﾞ隙間確認" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-5945", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付けできている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "銘板貼付け2", "WorkItems": [ "1. ①にLABEL を貼付ける" ], "WorkPoints": [ "240㎜", "40㎜", "163㎜", "5㎜", "5㎜", "186㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "45cN･m", "WorkName": "ﾌﾚｰﾑ組立4", "WorkItems": [ "1. ①にJOINT をBOLT ⑦WASHER で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m", "締付ﾄﾙｸ 45cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "45cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "ﾌﾚｰﾑ組立4", "WorkItems": [ "1. ①にJOINT をBOLT ⑦WASHER で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m", "締付ﾄﾙｸ 45cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾌﾚｰﾑ組立5", "WorkItems": [ "1. ①にCOVER COVER を取付ける", "2. 1完成品にCABLE-SUPPORT PLUG を取付ける" ], "WorkPoints": [ "88㎜", "134㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "ﾌﾚｰﾑ組立6", "WorkItems": [ "2. 1完成品にSPACER をBOLT WASHER で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾌﾚｰﾑ組立6", "WorkItems": [ "3. 2完成品にBOLT NUT を取付ける" ], "WorkPoints": [ "42㎜" ], "Tolks": [ "締付ﾄﾙｸ 2.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "7㎜", "ToolOther": "2.0N･m", "WorkName": "ﾌﾚｰﾑ組立6", "WorkItems": [ "3. 2完成品にBOLT NUT を取付ける" ], "WorkPoints": [ "42㎜" ], "Tolks": [ "締付ﾄﾙｸ 2.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "2.0N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "ｸﾞﾘｰｽLCG100", "WorkName": "ﾌﾚｰﾑ組立7", "WorkItems": [ "◆1. ①にｸﾞﾘｰｽを塗布する", "3. 2完成品にBRACKET をSPACER BOLT で取付ける" ], "WorkPoints": [ "ﾊﾞﾈとﾎﾞﾙﾄの接触部に塗布する(左右2ヶ所行う事)" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:各1", "◆作業者安全作業" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2㎜", "ToolOther": "100cN･m", "WorkName": "ﾌﾚｰﾑ組立7", "WorkItems": [ "2. 1完成品にSPRING を取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 100cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "◆作業者安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "100cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ﾌﾚｰﾑ組立8", "WorkItems": [ "1. ①にCABLE-SUPPORT を取付ける", "2. 1完成品に③をBOLT WASHER で取付ける" ], "WorkPoints": [ "B1344R" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "1.27㎜", "ToolOther": "3.2N･m", "WorkName": "ﾌﾚｰﾑ組立9", "WorkItems": [ "2. 1完成品にSPACER をBOLT WASHER で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾌﾚｰﾑ組立9", "WorkItems": [ "3. 2完成品にBOLT NUT を取付ける" ], "WorkPoints": [ "42㎜" ], "Tolks": [ "締付ﾄﾙｸ 2.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "7㎜", "ToolOther": "2.0N･m", "WorkName": "ﾌﾚｰﾑ組立9", "WorkItems": [ "3. 2完成品にBOLT NUT を取付ける" ], "WorkPoints": [ "42㎜" ], "Tolks": [ "締付ﾄﾙｸ 2.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "2.0N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "ｸﾞﾘｰｽLCG100", "WorkName": "ﾌﾚｰﾑ組立10", "WorkItems": [ "3. 2完成品に③をBOLT WASHER で取付ける", "◆1. ①にｸﾞﾘｰｽを塗布する" ], "WorkPoints": [ "ﾊﾞﾈとﾎﾞﾙﾄの接触部に塗布する(左右2ヶ所行う事)", "B1304R" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:各1", "◆作業者安全作業" ] }
{ "QualityItem": "塗布量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布米粒:各1", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "ﾌﾚｰﾑ組立10", "WorkItems": [ "3. 2完成品に③をBOLT WASHER で取付ける", "◆1. ①にｸﾞﾘｰｽを塗布する" ], "WorkPoints": [ "ﾊﾞﾈとﾎﾞﾙﾄの接触部に塗布する(左右2ヶ所行う事)", "B1304R" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "ｸﾞﾘｰｽ塗布 米粒:各1", "◆作業者安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "ﾊﾞﾙﾌﾞ組立", "WorkItems": [ "1. VALVE にSILENCER JOINT を取付ける", "2. 1完成品をBRACKET にBOLT SPACER WASHER で取付ける" ], "WorkPoints": [ "最初にJOINT を取付ける", "刻印有り" ], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "ﾊﾞﾙﾌﾞ組立", "WorkItems": [ "3. TUBE を指定の長さにｶｯﾄする", "4. 2完成品に3完成品､JOINT JOINT を差込む" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "連結部組立", "WorkItems": [ "1. BRACKET にCONNECTOR CONNECTOR をBOLT WASHER で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "連結部組立", "WorkItems": [ "3. 2完成品にCOVER を取付ける" ], "WorkPoints": [ "取付け方向に注意する事", "14㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ﾌﾟﾚｰﾄ組立1", "WorkItems": [ "1. PLATE にBRACKET BRACKET BRACKET BRACKET をBOLT WASHER で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾌﾟﾚｰﾄ組立1", "WorkItems": [ "2. 1完成品にCABLE-SUPPORT COVER を取付ける" ], "WorkPoints": [ "115㎜" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "3㎜", "ToolOther": "194cN･m", "WorkName": "ﾌﾟﾚｰﾄ組立2", "WorkItems": [ "1. ①に②をBOLT WASHER で取付ける", "2. 1完成品に③をBOLT WASHER で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 194cN･m", "締付ﾄﾙｸ 194cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "194cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸｽﾊﾟﾅ", "Size": "19㎜", "ToolOther": "25N･m", "WorkName": "ﾌﾟﾚｰﾄ前組み", "WorkItems": [ "1. ①に②を③④⑪⑯で取付ける", "2. ⑤に⑥⑦を⑧⑰⑱で仮に取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 10.9N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "仮止め:SD-A042069-520にて本締め" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "25N･m±10%", "Method": "ﾄﾙｸｽﾊﾟﾅ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "No.3", "ToolOther": "10.9N･m", "WorkName": "ﾌﾟﾚｰﾄ前組み", "WorkItems": [ "1. ①に②を③④⑪⑯で取付ける", "2. ⑤に⑥⑦を⑧⑰⑱で仮に取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 10.9N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "仮止め:SD-A042069-520にて本締め" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "10.9N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "", "ToolOther": "", "WorkName": "ﾌﾟﾚｰﾄ前組み", "WorkItems": [ "1. ①に②を③④⑪⑯で取付ける", "2. ⑤に⑥⑦を⑧⑰⑱で仮に取付ける" ], "WorkPoints": [ "87.5㎜±0.05㎜", "締付け手順①寸法を確保しながらﾀﾞﾌﾞﾙﾅｯﾄを締付ける②皿ﾋﾞｽを締付ける" ], "Tolks": [ "締付ﾄﾙｸ 25N･m", "締付ﾄﾙｸ 10.9N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "仮止め:SD-A042069-520にて本締め" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法:各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾉｷﾞｽ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾌﾟﾚｰﾄ前組み", "WorkItems": [ "1. ①に②を③④⑪⑯で取付ける", "2. ⑤に⑥⑦を⑧⑰⑱で仮に取付ける", "1. ①に②を③④⑪⑯で取付ける", "2. ⑤に⑥⑦を⑧⑰⑱で仮に取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 10.9N･m", "締付ﾄﾙｸ 10.9N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "仮止め:SD-A042069-520にて本締め", "仮止め:SD-A042069-520にて本締め" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "1回/年", "ToolRecord": "校正成績書", "StdVal": "87.5㎜±0.05㎜", "Method": "ﾉｷﾞｽ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾌﾞﾗｹｯﾄ前組み", "WorkItems": [ "1. BRACKET にBRACKET をBOLT WASHER で仮取付けする", "2. BRACKET にBRACKET をBOLT WASHER で仮取付けする", "3. 2完成品にCABLE-SUPPORT を取付ける" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "仮止め:SD-A042069-521にて本締め", "仮止め:SD-A042069-521にて本締め" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付けできている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null