text
stringlengths 9
3.82k
| document_url
stringclasses 574
values | source_url
stringclasses 574
values | country
stringclasses 44
values |
|---|---|---|---|
9.7.4 Earthing of FL vehicles Tanks made of metal or of fibre-reinforced plastics material of FL tank-vehicles and battery elements of FL battery-vehicles shall be linked to the chassis by means of at least one good electrical connection.
Any metal contact capable of causing electrochemical corrosion shall be avoided.
NOTE: See also 6.9.1.2 and 6.9.2.14.3. | https://docs-lawep.s3.us-east-2.amazonaws.com/thematic2a/pw_1/1715774115594.pdf | https://www.dfa.ie/media/dfa/alldfawebsitemedia/treatyseries/uploads/documents/legaldivisiondocuments/treatyseries2007/no-8-of-2007.pdf | Slovakia |
NOTE: See also 6.9.1.2 and 6.9.2.14.3.
9.7.5 Stability of tank-vehicles 9.7.5.1 The overall width of the ground-level bearing surface (distance between the outer points of contact with the ground of the right-hand tyre and the left-hand tyre of the same axle) shall be at least equal to 90% of the height of the centre of gravity of the laden tank-vehicle. | https://docs-lawep.s3.us-east-2.amazonaws.com/thematic2a/pw_1/1715774115594.pdf | https://www.dfa.ie/media/dfa/alldfawebsitemedia/treatyseries/uploads/documents/legaldivisiondocuments/treatyseries2007/no-8-of-2007.pdf | Slovakia |
In an articulated vehicle the mass on the axles of the load-carrying unit of the laden semi-trailer shall not exceed 60% of the nominal total laden mass of the complete articulated vehicle.
9.7.5.2 In addition, tank-vehicles with fixed tanks with a capacity of more than 3 m3 intended for the carriage of dangerous goods in the liquid or molten state tested with a pressure of less than 4 bar, shall comply with the technical requirements of ECE Regulation No. | https://docs-lawep.s3.us-east-2.amazonaws.com/thematic2a/pw_1/1715774115594.pdf | https://www.dfa.ie/media/dfa/alldfawebsitemedia/treatyseries/uploads/documents/legaldivisiondocuments/treatyseries2007/no-8-of-2007.pdf | Slovakia |
111 1 for lateral stability, as amended, in accordance with the dates of application specified therein.
The requirements are applicable to tank-vehicles which are first registered as from 1 July 2003.
9.7.6 Rear protection of vehicles A bumper sufficiently resistant to rear impact shall be fitted over the full width of the tank at the rear of the vehicle. | https://docs-lawep.s3.us-east-2.amazonaws.com/thematic2a/pw_1/1715774115594.pdf | https://www.dfa.ie/media/dfa/alldfawebsitemedia/treatyseries/uploads/documents/legaldivisiondocuments/treatyseries2007/no-8-of-2007.pdf | Slovakia |
There shall be a clearance of at least 100 mm between the rear wall of the tank and the rear of the bumper (this clearance being measured from the rearmost point of the tank wall or from projecting fittings or accessories in contact with the substance being carried).
Vehicles with a tilting shell 1 ECE Regulation No.
111: Uniform provisions concerning the approval of tank- vehicles of categories N and O with regard to rollover stability. | https://docs-lawep.s3.us-east-2.amazonaws.com/thematic2a/pw_1/1715774115594.pdf | https://www.dfa.ie/media/dfa/alldfawebsitemedia/treatyseries/uploads/documents/legaldivisiondocuments/treatyseries2007/no-8-of-2007.pdf | Slovakia |
- 699 - for the carriage of powdery or granular substances and a vacuum-operated waste tank with a tilting shell with rear discharge do not require a bumper if the rear fittings of the shell are provided with a means of protection which protects the shell in the same way as a bumper.
NOTE 1: This provision does not apply to vehicles used for the carriage of dangerous goods in tank-containers, MEGCs or portable tanks. | https://docs-lawep.s3.us-east-2.amazonaws.com/thematic2a/pw_1/1715774115594.pdf | https://www.dfa.ie/media/dfa/alldfawebsitemedia/treatyseries/uploads/documents/legaldivisiondocuments/treatyseries2007/no-8-of-2007.pdf | Slovakia |
NOTE 2: For the protection of tanks against damage by lateral impact or overturning, see 6.8.2.1.20 and 6.8.2.1.21 or, for portable tanks, 6.7.2.4.3 and 6.7.2.4.5. | https://docs-lawep.s3.us-east-2.amazonaws.com/thematic2a/pw_1/1715774115594.pdf | https://www.dfa.ie/media/dfa/alldfawebsitemedia/treatyseries/uploads/documents/legaldivisiondocuments/treatyseries2007/no-8-of-2007.pdf | Slovakia |
9.7.7 Combustion heaters 9.7.7.1 Combustion heaters shall meet the requirements of 9.2.4.7.1, 9.2.4.7.2, 9.2.4.7.5 and the following: (a) The switch may be installed outside the driver's cab; (b) The device may be switched off from outside the load compartment; and (c) It is not necessary to prove that the heat exchanger is resistant to the reduced afterrunning cycle.
In addition for FL vehicles, they shall meet the requirements of 9.2.4.7.3 and 9.2.4.7.4. | https://docs-lawep.s3.us-east-2.amazonaws.com/thematic2a/pw_1/1715774115594.pdf | https://www.dfa.ie/media/dfa/alldfawebsitemedia/treatyseries/uploads/documents/legaldivisiondocuments/treatyseries2007/no-8-of-2007.pdf | Slovakia |
9.7.7.2 If the vehicle is intended for the carriage of dangerous goods for which a label conforming to models Nos.
3, 4.1, 4.3, 5.1 or 5.2 is prescribed, no fuel tanks, power sources, combustion air or heating air intakes as well as exhaust tube outlets required for the operation of the combustion heater shall be installed in the load compartment.
It shall be ensured that the heating air outlet cannot be blocked by cargo.
The temperature to which the load is heated shall not exceed 50 ºC. | https://docs-lawep.s3.us-east-2.amazonaws.com/thematic2a/pw_1/1715774115594.pdf | https://www.dfa.ie/media/dfa/alldfawebsitemedia/treatyseries/uploads/documents/legaldivisiondocuments/treatyseries2007/no-8-of-2007.pdf | Slovakia |
Heating devices installed inside the load compartments shall be designed so as to prevent the ignition of an explosive atmosphere under operating conditions.
- 699 - 9.7.8 Electrical equipment 9.7.8.1 The electrical installation on FL vehicles for which an approval according to 9.1.2 is required shall meet the requirements of 9.2.2.2, 9.2.2.3, 9.2.2.4, 9.2.2.5.1 and 9.2.2.6. | https://docs-lawep.s3.us-east-2.amazonaws.com/thematic2a/pw_1/1715774115594.pdf | https://www.dfa.ie/media/dfa/alldfawebsitemedia/treatyseries/uploads/documents/legaldivisiondocuments/treatyseries2007/no-8-of-2007.pdf | Slovakia |
However additions to or modifications of the electrical installations of the vehicle shall meet the requirements for the electrical apparatus of the relevant group and temperature class according to the substances to be carried.
NOTE: For transitional provisions, see also 1.6.5. | https://docs-lawep.s3.us-east-2.amazonaws.com/thematic2a/pw_1/1715774115594.pdf | https://www.dfa.ie/media/dfa/alldfawebsitemedia/treatyseries/uploads/documents/legaldivisiondocuments/treatyseries2007/no-8-of-2007.pdf | Slovakia |
NOTE: For transitional provisions, see also 1.6.5.
9.7.8.2 Electrical equipment on FL vehicles, situated in areas where an explosive atmosphere is, or may be expected to be, present in such quantities as to require special precautions, shall be suitable for use in a hazardous area.
Such equipment shall meet the general requirements of IEC 60079 parts 0 and 14 and the additional requirements applicable form IEC 60079 parts 1, 2, 5, 6, 7, 11 or 18 2. | https://docs-lawep.s3.us-east-2.amazonaws.com/thematic2a/pw_1/1715774115594.pdf | https://www.dfa.ie/media/dfa/alldfawebsitemedia/treatyseries/uploads/documents/legaldivisiondocuments/treatyseries2007/no-8-of-2007.pdf | Slovakia |
The requirements for the electrical apparatus of the relevant group and temperature class according to the substances to be carried shall be met.
For the application of IEC 60079 part 14 2, the following classification shall be used: ZONE 0 Inside tank compartments, fittings for filling and discharge and vapour recovery lines.
ZONE 1 Inside cabinets for equipment used for filling and discharge and within 0.5 m of venting devices and pressure relief safety valves. | https://docs-lawep.s3.us-east-2.amazonaws.com/thematic2a/pw_1/1715774115594.pdf | https://www.dfa.ie/media/dfa/alldfawebsitemedia/treatyseries/uploads/documents/legaldivisiondocuments/treatyseries2007/no-8-of-2007.pdf | Slovakia |
9.7.8.3 Permanently energized electrical equipment, including the leads, which is situated outside Zones 0 and 1 shall meet the requirements for Zone 1 for electrical equipment in general or meet the requirements for Zone 2 according to IEC 60079 part 14 2 for electrical equipment situated in the driver's cab.
The requirements for the relevant group of electrical apparatus according to the substances to be carried shall be met. | https://docs-lawep.s3.us-east-2.amazonaws.com/thematic2a/pw_1/1715774115594.pdf | https://www.dfa.ie/media/dfa/alldfawebsitemedia/treatyseries/uploads/documents/legaldivisiondocuments/treatyseries2007/no-8-of-2007.pdf | Slovakia |
2 As an alternative, the general requirements of EN 50014 and the additional requirements of EN 50015, 50016, 50017, 50018, 50019, 50020 or 50028 may be used.
- 699 - | https://docs-lawep.s3.us-east-2.amazonaws.com/thematic2a/pw_1/1715774115594.pdf | https://www.dfa.ie/media/dfa/alldfawebsitemedia/treatyseries/uploads/documents/legaldivisiondocuments/treatyseries2007/no-8-of-2007.pdf | Slovakia |