input stringclasses 1 value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "80cN･m",
"WorkName": "電源部取付け",
"WorkItems": [
"1. ①に②をSCREW で取付ける",
"2. 1完成品にCONNECTOR-ACCESSORIES を取付ける"
],
"WorkPoints": [
"取付方向に注意"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "電源部配線接続",
"WorkItems": [
"1. ①の電源ﾕﾆｯﾄからのP1､J2を､それぞれ指定箇所に差込む",
"2. 電源配線をｲﾝｼｭﾛｯｸで結束する"
],
"WorkPoints": [
"ｶﾁｯと音がするまで確実に差込む事",
"ﾚｰﾙに触れないよう配線の中心を束ねる事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"P1(6ﾋﾟﾝ)",
"J2(20ﾋﾟﾝ)",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾊﾞｰ取付け①",
"WorkItems": [
"1. ①にCOVER かぶせ､SCREW で仮締結する(9箇所)"
],
"WorkPoints": [
"SD-A052331-020,021で本締結",
"配線の挟み込まないよう注意する事",
"COVER のｶﾊﾞｰが内側に来るように取付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾛｯﾄ位置決め①",
"WorkItems": [
"■1. NCIO3 BOARD(MEL) の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入する",
"2. ②の指定箇所に､NCIO3 BOARD(MEL) を挿入しながら､PCB-COMとの差込具合を確認する"
],
"WorkPoints": [
"ここのくぼみ部に基板を差込む事",
"差込位置､方向を間違え無い事",
"ﾌｯｸが確実にかかるか確認する事",
"無理に押し込ま無い事",
"矢印部を押しながらﾚﾊﾞｰを上げゆっくり取付ける事"
],
"Tolks": [],
"InspectionNo": "2LC-JG-23011",
"InspectionItems": [
"検査表NCIO3 BOARD(MEL) :1.構成ﾁｪｯｸ"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"2LC-JG-23011"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "2LC-JG-23011",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾛｯﾄ位置決め①",
"WorkItems": [
"■1. NCIO3 BOARD(MEL) の型式ﾁｪｯｸ､ｼﾘｱﾙNo.記入､検査書有無を確認し検査表に記入する",
"2. ②の指定箇所に､NCIO3 BOARD(MEL) を挿入しながら､PCB-COMとの差込具合を確認する"
],
"WorkPoints": [
"ここのくぼみ部に基板を差込む事",
"差込位置､方向を間違え無い事",
"ﾌｯｸが確実にかかるか確認する事",
"無理に押し込ま無い事",
"矢印部を押しながらﾚﾊﾞｰを上げゆっくり取付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表NCIO3 BOARD(MEL) :1.構成ﾁｪｯｸ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾛｯﾄ位置決め②",
"WorkItems": [
"1. ②の指定箇所に､①を挿入しながら､PCB-COMとの差込具合を確認する"
],
"WorkPoints": [
"ここのくぼみ部に基板を差込む事",
"無理に押し込ま無い事",
"差込位置､方向を間違え無い事",
"ﾌｯｸが確実にかかるか確認する事",
"矢印部を押しながらﾚﾊﾞｰを上げゆっくり取付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "26cN･m",
"WorkName": "PCB-COM締付",
"WorkItems": [
"1. ①の裏面を手前にする",
"2. 仮固定したPCB-COM基板のﾈｼﾞを本締めする(6箇所)"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 26cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "26cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "120cN･m",
"WorkName": "ｶﾊﾞｰ締付①",
"WorkItems": [
"1. ①のｶﾊﾞｰとﾚｰﾙを仮固定したﾈｼﾞを､本締めする(10箇所)"
],
"WorkPoints": [
"左側面",
"右側面"
],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "120cN･m",
"WorkName": "ｶﾊﾞｰ締付②",
"WorkItems": [
"2. 締結確認後､NC/IOﾎﾞｰﾄﾞ､CPUﾎﾞｰﾄﾞを外す",
"1. ①のｶﾊﾞｰとﾌﾞﾗｹｯﾄを仮固定したﾈｼﾞを､本締めする(4箇所)"
],
"WorkPoints": [
"2つのﾎﾞｰﾄﾞを外す"
],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線接続",
"WorkItems": [
"1. ①の裏面を手前にする",
"2. CABLE のJ2､P3､CN4を､それぞれ指定箇所に差込む",
"3. J2の配線にCN4の配線を余長分折り曲げてｲﾝｼｭﾛｯｸで結束する"
],
"WorkPoints": [
"ｶﾁｯと音がするまで確実に差込む事",
"P3(2ﾋﾟﾝ)のｺﾈｸﾀはJ2(20ﾋﾟﾝ)の内側を通すこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ(100mm)",
"CN4(4ﾋﾟﾝ)",
"J2(4ﾋﾟﾝ)",
"P3(2ﾋﾟﾝ)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "120cN･m",
"WorkName": "FAN取付け",
"WorkItems": [
"1. COVER の指定箇所に､GUARD とFAN を重ね合わせる",
"2. COVER と､重ねたGUARD FAN の穴位置を合わせて､SCREW で締結する"
],
"WorkPoints": [
"ﾗﾍﾞﾙが見えるように取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "120cN･m",
"WorkName": "ﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. BRACKET の爪を③の抜き穴に奥まで入れた後､抜きながら倒し､穴位置を合せる事",
"2. BRACKET ③の穴位置確認後､SCREW で締結する"
],
"WorkPoints": [
"板金に負荷がかからないように注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "120cN･m",
"WorkName": "ｶﾊﾞｰ取付け②",
"WorkItems": [
"1. ③に②を取付け､SCREW で締結する",
"2. FANの配線を接続する"
],
"WorkPoints": [
"配線を挟み込まないように注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｨﾙﾀｰｷｯﾄ挿入",
"WorkItems": [
"1. ②に①を差込む"
],
"WorkPoints": [
"ﾗﾊﾞｰｸｯｼｮﾝがﾊﾟﾝﾁ穴に引っ掛かっている事を確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃｽﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "出力電圧確認",
"WorkItems": [],
"WorkPoints": [
"規格値:出力電圧･･･11.4~12.6V",
"規格値:出力電圧･･･11.4~12.6V"
],
"Tolks": [],
"InspectionNo": "2LC-JG-20017",
"InspectionItems": [
"検査表①:2.出力電圧",
"検査表①:2.出力電圧"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"P2",
"電源",
"電源ｹｰﾌﾞﾙ",
"2LC-JG-20017"
]
} | {
"QualityItem": "出力電圧確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績表",
"StdVal": "11.4~12.6V",
"Method": "ﾃｽﾀｰ",
"RecordMethod": "2LC-JG-20017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "出力電圧確認用治具",
"Size": "",
"ToolOther": "FM-5809",
"WorkName": "出力電圧確認",
"WorkItems": [
"7. ①の電源をOFFする",
"6. 同様に㉖のﾌﾟﾛｰﾌﾞを㉗のNo.４（黒）、６（赤）に当て電圧を測定する",
"5. ㉖のﾌﾟﾛｰﾌﾞを㉗のNo.１（黒）、３（赤）に当て電圧を測定する",
"1. ①のP2ｺﾈｸﾀに㉗を接続する",
"4. ㉖のファンクションスイッチを電圧に合わせる",
"3. ①の電源をONする",
"2. 電源ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "2LC-JG-20017",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"2LC-JG-20017"
]
} | {
"QualityItem": "出力電圧確認",
"ToolManageNo": "FM-5809",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "11.4~12.6V",
"Method": "出力電圧確認用治具",
"RecordMethod": "2LC-JG-20017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃｽﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾞｯｸﾌﾟﾚｰﾝ電圧確認",
"WorkItems": [
"1. ㉖を①の一番左側に差込む",
"2. ①の電源をONする",
"3. ㉗のファンクションスイッチを電圧に合わせる"
],
"WorkPoints": [
"規格値:出力電圧･･･5V±5%"
],
"Tolks": [],
"InspectionNo": "2LC-JG-20017",
"InspectionItems": [
"検査表①:3.ﾊﾞｯｸﾌﾟﾚｰﾝ電圧"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"2LC-JG-20017"
]
} | {
"QualityItem": "ﾊﾞｯｸﾌﾟﾚｰﾝ電圧確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績表",
"StdVal": "5V±5%12V±5%",
"Method": "ﾃｽﾀｰ",
"RecordMethod": "2LC-JG-20017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "治具ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-5808",
"WorkName": "ﾊﾞｯｸﾌﾟﾚｰﾝ電圧確認",
"WorkItems": [
"1. ㉖を①の一番左側に差込む",
"2. ①の電源をONする",
"3. ㉗のファンクションスイッチを電圧に合わせる"
],
"WorkPoints": [
"規格値:出力電圧･･･5V±5%"
],
"Tolks": [],
"InspectionNo": "2LC-JG-20017",
"InspectionItems": [
"検査表①:3.ﾊﾞｯｸﾌﾟﾚｰﾝ電圧"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"2LC-JG-20017"
]
} | {
"QualityItem": "ﾊﾞｯｸﾌﾟﾚｰﾝ電圧確認",
"ToolManageNo": "FM-5808",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "5V±5%12V±5%",
"Method": "治具ﾎﾞｰﾄﾞ",
"RecordMethod": "2LC-JG-20017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｵｼﾛｽｺｰﾌﾟ",
"Size": "",
"ToolOther": "",
"WorkName": "FANｱﾗｰﾑ出力確認",
"WorkItems": [
"1. ㉗を①の左側に差込み、㉘のﾌﾟﾛｰﾌﾞを㉗の任意の箇所に接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "2LC-JG-20017",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"外部FAN",
"GND",
"2LC-JG-20017"
]
} | {
"QualityItem": "FANｱﾗｰﾑ出力確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績表",
"StdVal": "Highﾚﾍﾞﾙ3.0±0.75ms",
"Method": "ｵｼﾛｽｺｰﾌﾟ",
"RecordMethod": "2LC-JG-20017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "治具ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-5808",
"WorkName": "FANｱﾗｰﾑ出力確認",
"WorkItems": [
"1. ㉗を①の左側に差込み、㉘のﾌﾟﾛｰﾌﾞを㉗の任意の箇所に接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"外部FAN",
"GND",
"2LC-JG-20017"
]
} | {
"QualityItem": "FANｱﾗｰﾑ出力確認",
"ToolManageNo": "FM-5808",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "Highﾚﾍﾞﾙ3.0±0.75ms",
"Method": "治具ﾎﾞｰﾄﾞ",
"RecordMethod": "2LC-JG-20017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN取付け方向確認",
"WorkItems": [
"1. ①の電源をONする",
"2. FANの風向きが排気方向になっているか確認し､電源をOFFする",
"5. ｵｼﾛｽｺｰﾌﾟの波形のﾊﾟﾙｽ幅を測定する",
"4. ①の電源をONし､FANの回転が安定する事を確認する",
"3. ㉗のﾌﾟﾛｰﾌﾞを㉖の任意の箇所に接続する",
"6. 各電源をOFFし､治具を外す"
],
"WorkPoints": [
"規格値:ﾊﾟﾙｽ幅･･･3.0±0.75ms",
"①ｵｼﾛｽｺｰﾌﾟの電源をON②CURSORを押す③ﾀﾞｲﾔﾙを動かし､右側の波形に合わせる④数値を読み記入する"
],
"Tolks": [],
"InspectionNo": "2LC-JG-20017",
"InspectionItems": [
"検査表①:5.FAN取付方向"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"FAN",
"GND",
"検査表①:4.FANｱﾗｰﾑ出力",
"2LC-JG-20017"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "風向きが排気方向になっているか確認する事",
"Method": "目視",
"RecordMethod": "2LC-JG-20017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｵｼﾛｽｺｰﾌﾟ",
"Size": "",
"ToolOther": "",
"WorkName": "FAN取付け方向確認",
"WorkItems": [
"1. ①の電源をONする",
"2. FANの風向きが排気方向になっているか確認し､電源をOFFする",
"5. ｵｼﾛｽｺｰﾌﾟの波形のﾊﾟﾙｽ幅を測定する",
"4. ①の電源をONし､FANの回転が安定する事を確認する",
"3. ㉗のﾌﾟﾛｰﾌﾞを㉖の任意の箇所に接続する",
"6. 各電源をOFFし､治具を外す"
],
"WorkPoints": [
"規格値:ﾊﾟﾙｽ幅･･･3.0±0.75ms",
"①ｵｼﾛｽｺｰﾌﾟの電源をON②CURSORを押す③ﾀﾞｲﾔﾙを動かし､右側の波形に合わせる④数値を読み記入する"
],
"Tolks": [],
"InspectionNo": "2LC-JG-20017",
"InspectionItems": [
"検査表①:4.FANｱﾗｰﾑ出力"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"FAN",
"GND",
"検査表①:5.FAN取付方向",
"2LC-JG-20017"
]
} | {
"QualityItem": "FANｱﾗｰﾑ出力確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績表",
"StdVal": "Highﾚﾍﾞﾙ3.0±0.75ms",
"Method": "ｵｼﾛｽｺｰﾌﾟ",
"RecordMethod": "2LC-JG-20017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "治具ﾎﾞｰﾄﾞ",
"Size": "",
"ToolOther": "FM-5808",
"WorkName": "FAN取付け方向確認",
"WorkItems": [
"1. ①の電源をONする",
"2. FANの風向きが排気方向になっているか確認し､電源をOFFする",
"5. ｵｼﾛｽｺｰﾌﾟの波形のﾊﾟﾙｽ幅を測定する",
"4. ①の電源をONし､FANの回転が安定する事を確認する",
"3. ㉗のﾌﾟﾛｰﾌﾞを㉖の任意の箇所に接続する",
"6. 各電源をOFFし､治具を外す"
],
"WorkPoints": [
"規格値:ﾊﾟﾙｽ幅･･･3.0±0.75ms",
"①ｵｼﾛｽｺｰﾌﾟの電源をON②CURSORを押す③ﾀﾞｲﾔﾙを動かし､右側の波形に合わせる④数値を読み記入する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"FAN",
"GND",
"検査表①:5.FAN取付方向",
"検査表①:4.FANｱﾗｰﾑ出力",
"2LC-JG-20017"
]
} | {
"QualityItem": "FANｱﾗｰﾑ出力確認",
"ToolManageNo": "FM-5808",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "Highﾚﾍﾞﾙ3.0±0.75ms",
"Method": "治具ﾎﾞｰﾄﾞ",
"RecordMethod": "2LC-JG-20017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け①",
"WorkItems": [
"■1. ②にLABEL を指定寸法で貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "2LC-JG-20017",
"InspectionItems": [
"検査表LABEL :9.ﾗﾍﾞﾙ貼付"
],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"10±1",
"135±1",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け①",
"WorkItems": [
"■1. ②にLABEL を指定寸法で貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"10±1",
"135±1",
"検査表LABEL :9.ﾗﾍﾞﾙ貼付",
"2LC-JG-20017"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "所定の位置に貼付けられている事",
"Method": "目視",
"RecordMethod": "2LC-JG-20017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗｲｾﾝｽｼｰﾙ貼付け",
"WorkItems": [
"1. ①の指定個所にSOFTWARE-LICENSE SOFTWARE-LICENSE SOFTWARE-LICENSE SOFTWARE-LICENSE を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "2LC-JG-23011",
"InspectionItems": [
"検査表①:5.ﾗｲｾﾝｽｼｰﾙ"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"10mm",
"5mm",
"5mm",
"5mm",
"5mm"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾗｲｾﾝｽｼｰﾙ貼付け",
"WorkItems": [
"1. ①の指定個所にSOFTWARE-LICENSE SOFTWARE-LICENSE SOFTWARE-LICENSE SOFTWARE-LICENSE を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"10mm",
"5mm",
"5mm",
"検査表①:5.ﾗｲｾﾝｽｼｰﾙ",
"5mm",
"5mm",
"2LC-JG-23011"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "各ﾗｲｾﾝｽｼｰﾙが指示通り貼付されている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23011",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け②",
"WorkItems": [
"■1. ②に①を指定寸法で貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "2LC-JG-20017",
"InspectionItems": [
"検査表①:9.ﾗﾍﾞﾙ貼付"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"30±1",
"5±1",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾗﾍﾞﾙ貼付け②",
"WorkItems": [
"■1. ②に①を指定寸法で貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"30±1",
"5±1",
"検査表①:9.ﾗﾍﾞﾙ貼付",
"2LC-JG-20017"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "所定の位置に貼付けられている事",
"Method": "目視",
"RecordMethod": "2LC-JG-20017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "基板の締付",
"WorkItems": [
"1. ①に②③を挿入する",
"2. ①の各基板の付属ﾈｼﾞを締付固定する(6箇所)"
],
"WorkPoints": [
"無理に押し込ま無い事",
"差込位置､方向を間違え無い事",
"ﾌｯｸが確実にかかるか確認する事"
],
"Tolks": [
"締付ﾄﾙｸ 26cN･m"
],
"InspectionNo": "2LC-JG-23011",
"InspectionItems": [
"検査表①:3.目視検査",
"検査表①:3.目視検査"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"2LC-JG-23011"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23011",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.1",
"ToolOther": "26cN･m",
"WorkName": "基板の締付",
"WorkItems": [
"1. ①に②③を挿入する",
"2. ①の各基板の付属ﾈｼﾞを締付固定する(6箇所)"
],
"WorkPoints": [
"無理に押し込ま無い事",
"差込位置､方向を間違え無い事",
"ﾌｯｸが確実にかかるか確認する事"
],
"Tolks": [
"締付ﾄﾙｸ 26cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:3.目視検査",
"検査表①:3.目視検査"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "26cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｾｯﾄｱｯﾌﾟ",
"WorkItems": [
"1. ①の指定箇所に､ｺﾈｸﾀ(ﾓﾆﾀｰ､ｷｰﾎﾞｰﾄﾞ､ﾏｳｽ)を接続する",
"2. ①にﾓﾆﾀｰ用の電源ｹｰﾌﾞﾙと①の電源ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｷｰﾎﾞｰﾄﾞ",
"ﾓﾆﾀｰ",
"ﾏｳｽ",
"ﾓﾆﾀｰ用電源",
"P10A電源"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶｰﾈﾙｲﾝｽﾄｰﾙ(P10A)",
"WorkItems": [
"1. 手順書【2LC-JF-19007】を参照し､ｶｰﾈﾙｲﾝｽﾄｰﾙを行う",
"2. 1完成品にLABEL を貼付ける"
],
"WorkPoints": [
"ﾊﾟﾈﾙのｼﾙｸ印刷ﾗｲﾝに合わせて貼付ける"
],
"Tolks": [],
"InspectionNo": "2LC-JG-21011",
"InspectionItems": [
"検査表①:4.OSのﾊﾞｰｼﾞｮﾝの確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:7.品番ﾗﾍﾞﾙの貼付",
"2LC-JG-21011"
]
} | {
"QualityItem": "OSのﾊﾞｰｼﾞｮﾝ確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "OSのﾊﾞｰｼﾞｮﾝが一致する事",
"Method": "目視",
"RecordMethod": "2LC-JG-21011",
"Other": "書込み仕様2LC-JR-23013",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶｰﾈﾙｲﾝｽﾄｰﾙ(P10A)",
"WorkItems": [
"1. 手順書【2LC-JF-19007】を参照し､ｶｰﾈﾙｲﾝｽﾄｰﾙを行う",
"2. 1完成品にLABEL を貼付ける"
],
"WorkPoints": [
"ﾊﾟﾈﾙのｼﾙｸ印刷ﾗｲﾝに合わせて貼付ける"
],
"Tolks": [],
"InspectionNo": "2LC-JG-21011",
"InspectionItems": [
"検査表①:7.品番ﾗﾍﾞﾙの貼付"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:4.OSのﾊﾞｰｼﾞｮﾝの確認",
"2LC-JG-21011"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示位置に貼付け出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-21011",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "接地抵抗試験機",
"Size": "",
"ToolOther": "",
"WorkName": "接地抵抗試験",
"WorkItems": [
"1. ①の指定箇所に、㉗を接続する",
"2. ﾃｽﾄ用ﾜﾆ口ｸﾘｯﾌﾟを治具の黒線側に接続し㉖の電源をONする",
"3. ①の電源をONする",
"■4. 接地抵抗試験機の『MAIN』ﾎﾞﾀﾝを押し､MAINﾎﾞﾀﾝが点灯している事を確認する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "2LC-JG-23011",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"MAIN",
"■安全作業",
"2LC-JG-23011"
]
} | {
"QualityItem": "接地抵抗確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "日常点検表",
"StdVal": "10A・10秒間・0.1Ω以下",
"Method": "接地抵抗試験機",
"RecordMethod": "2LC-JG-23011",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "耐圧試験用治具",
"Size": "",
"ToolOther": "FM-5810",
"WorkName": "接地抵抗試験",
"WorkItems": [
"1. ①の指定箇所に、㉗を接続する",
"2. ﾃｽﾄ用ﾜﾆ口ｸﾘｯﾌﾟを治具の黒線側に接続し㉖の電源をONする",
"3. ①の電源をONする",
"■4. 接地抵抗試験機の『MAIN』ﾎﾞﾀﾝを押し､MAINﾎﾞﾀﾝが点灯している事を確認する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "2LC-JG-23011",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"MAIN",
"■安全作業",
"2LC-JG-23011"
]
} | {
"QualityItem": "接地抵抗確認",
"ToolManageNo": "FM-5810",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "10A・10秒間・0.1Ω以下",
"Method": "耐圧試験用治具",
"RecordMethod": "2LC-JG-23011",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "絶縁抵抗試験機",
"Size": "",
"ToolOther": "",
"WorkName": "絶縁抵抗試験",
"WorkItems": [
"1. ①の指定箇所に、㉗を接続する。",
"2. ﾃｽﾄ用ﾜﾆ口ｸﾘｯﾌﾟ黒を治具の黒線側にｸﾘｯﾌﾟ赤を赤線側に接続し㉖の電源をONする。",
"3. ①の電源をONする｡",
"8. 実測値を検査書に記入する｡",
"■4. 耐圧試験機の『IR』ﾎﾞﾀﾝを押し､IRﾎﾞﾀﾝが点灯している事を確認する｡",
"■5. 『STOP』ﾎﾞﾀﾝを押す｡",
"■6. 耐圧試験機の両端の『START』ﾎﾞﾀﾝを同時に押し測定する｡",
"■7. 測定値を目視し､20MΩ以上である事を確認する｡"
],
"WorkPoints": [
"規格値:絶縁抵抗試験･･･DC500V 60秒間 20MΩ以上",
"但し､20MΩ以上になった時点で打ち切り可"
],
"Tolks": [],
"InspectionNo": "2LC-JG-23011",
"InspectionItems": [
"検査表①:6.絶縁抵抗試験"
],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"IR",
"2LC-JG-23011"
]
} | {
"QualityItem": "絶縁抵抗確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "日常点検表",
"StdVal": "DC500V・60秒間・20MΩ以上",
"Method": "絶縁抵抗試験機",
"RecordMethod": "2LC-JG-23011",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "耐圧試験用治具",
"Size": "",
"ToolOther": "FM-5810",
"WorkName": "絶縁抵抗試験",
"WorkItems": [
"1. ①の指定箇所に、㉗を接続する。",
"2. ﾃｽﾄ用ﾜﾆ口ｸﾘｯﾌﾟ黒を治具の黒線側にｸﾘｯﾌﾟ赤を赤線側に接続し㉖の電源をONする。",
"3. ①の電源をONする｡",
"■4. 耐圧試験機の『IR』ﾎﾞﾀﾝを押し､IRﾎﾞﾀﾝが点灯している事を確認する｡"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"IR",
"■安全作業",
"2LC-JG-23011"
]
} | {
"QualityItem": "絶縁抵抗確認",
"ToolManageNo": "FM-5810",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "DC500V・60秒間・20MΩ以上",
"Method": "耐圧試験用治具",
"RecordMethod": "2LC-JG-23011",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "絶縁抵抗試験機",
"Size": "",
"ToolOther": "",
"WorkName": "絶縁耐圧試験",
"WorkItems": [
"2. ﾃｽﾄ用ﾜﾆ口ｸﾘｯﾌﾟ黒を治具の黒線側にｸﾘｯﾌﾟ赤を赤線側に接続し㉖の電源をONする",
"3. ①の電源をONする",
"■4. 耐圧試験機の『ACW』ﾎﾞﾀﾝを押し､ACWﾎﾞﾀﾝが点灯している事を確認する",
"■5. 『STOP』ﾎﾞﾀﾝを押す",
"■6. 耐圧試験機の両端の『START』ﾎﾞﾀﾝを同時に押し測定する",
"1. ①の指定箇所に、㉗を接続する",
"9. 終了後､各電源をOFFし､治具を外す",
"8. 実測値を検査書に記入する",
"■7. 正常終了するとﾌﾞｻﾞｰが1回鳴り表示部右上に『PASS』表示が一瞬点灯する事を確認する"
],
"WorkPoints": [
"規格値:絶縁耐圧試験･･･AC1400V 2秒間 20mA以下"
],
"Tolks": [],
"InspectionNo": "2LC-JG-23011",
"InspectionItems": [
"検査表①:2.安全試験"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ACW",
"PASS",
"2LC-JG-23011"
]
} | {
"QualityItem": "絶縁耐圧確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "日常点検表",
"StdVal": "AC1400V・2秒間・20mA以下",
"Method": "絶縁抵抗試験機",
"RecordMethod": "2LC-JG-23011",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "耐圧試験用治具",
"Size": "",
"ToolOther": "FM-5810",
"WorkName": "絶縁耐圧試験",
"WorkItems": [
"2. ﾃｽﾄ用ﾜﾆ口ｸﾘｯﾌﾟ黒を治具の黒線側にｸﾘｯﾌﾟ赤を赤線側に接続し㉖の電源をONする",
"3. ①の電源をONする",
"■4. 耐圧試験機の『ACW』ﾎﾞﾀﾝを押し､ACWﾎﾞﾀﾝが点灯している事を確認する",
"1. ①の指定箇所に、㉗を接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ACW",
"■安全作業",
"2LC-JG-23011"
]
} | {
"QualityItem": "絶縁耐圧確認",
"ToolManageNo": "FM-5810",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "AC1400V・2秒間・20mA以下",
"Method": "耐圧試験用治具",
"RecordMethod": "2LC-JG-23011",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｴｰｼﾞﾝｸﾞ試験",
"WorkItems": [
"1. ①にｴｰｼﾞﾝｸﾞ装置からのｹｰﾌﾞﾙを接続する",
"2. 検査条件の設定を行う",
"3. 恒温槽の設定を行う",
"4. ｴｰｼﾞﾝｸﾞ試験を実施する"
],
"WorkPoints": [
"【NCIO】 CN9 ~CN8 信号ｹｰﾌﾞﾙ CN6 ~CN7 ﾌｧｲﾊﾞｰｹｰﾌﾞﾙ【CPU】 CRT ﾃﾞｨｽﾌﾟﾚｲｹｰﾌﾞﾙ COM1 RS232Cｹｰﾌﾞﾙ USB1 ﾁｪｯｶｰ用USB【CAMIF】 CN2 ｶﾒﾗﾘﾝｸｹｰﾌﾞﾙ",
"【ﾃｽﾄ1】\t240分､分指定にﾁｪｯｸ【ﾃｽﾄ2】\t100回､ｵﾝｵﾌにﾁｪｯｸ【ﾃｽﾄ3~5】\t1回､なにもﾁｪｯｸしない※ﾃｽﾄ1~5すべてﾊﾟﾀｰﾝはpat1を選択【全ｻｲｸﾙ数】\t2"
],
"Tolks": [],
"InspectionNo": "2LC-JG-23011",
"InspectionItems": [
"検査表①:4.ｴｰｼﾞﾝｸﾞ試験"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"注小さい方のﾀｯﾁﾊﾟﾈﾙの場合ここのﾁｪｯｸはしないでください",
"2LC-JG-23011"
]
} | {
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り出来ている事",
"Method": "目視",
"RecordMethod": "2LC-JG-23011",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "40cN･m",
"WorkName": "昇降ｾﾝｻｰ組立",
"WorkItems": [
"1. BRACKET にSENSOR をBOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"SENSOR の凸をBRACKET の凹に挿入する"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "WETE-G002-C10",
"InspectionItems": [
"検査表BRACKET :ﾌｫﾄｾﾝｻｰの締付ﾄﾙｸ"
],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾞﾙﾌﾞ組立",
"WorkItems": [
"1. VALVE にJOINT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "17㎜",
"ToolOther": "10N･m",
"WorkName": "昇降ｼﾘﾝﾀﾞｰ組立",
"WorkItems": [
"2. 1完成品にSPEED-CONTROLLER を取付ける"
],
"WorkPoints": [
"Dｶｯﾄあり"
],
"Tolks": [
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "1.2N･m",
"WorkName": "昇降ｼﾘﾝﾀﾞｰ組立",
"WorkItems": [
"2. 1完成品にSPEED-CONTROLLER を取付ける"
],
"WorkPoints": [
"Dｶｯﾄあり"
],
"Tolks": [
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降ｼﾘﾝﾀﾞｰ組立",
"WorkItems": [
"2. 1完成品にSPEED-CONTROLLER を取付ける"
],
"WorkPoints": [
"Dｶｯﾄあり"
],
"Tolks": [
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ｼﾘﾝﾀﾞｰ組立",
"WorkItems": [
"2. 1完成品にSPEED-CONTROLLER を取付ける",
"◆4. 3完成品に㉜を塗布する",
"1. CYLINDER にJOINT を付属NUTで取付ける",
"3. 2完成品のｽﾋﾟｺﾝを仮調整する"
],
"WorkPoints": [
"CYLINDER のｼｬﾌﾄ先端(Dｶｯﾄなし側)にJOINT を取付ける事",
"JOINT ｼﾞｮｲﾝﾄの内溝全域に塗布する事(赤色部)",
"CYLINDER を下降状態にして､規格寸法に調整する事",
"Dｶｯﾄなし",
"Dｶｯﾄあり",
"上昇側:全閉より1.5回転開く",
"下降側:全閉より2.0回転開く"
],
"Tolks": [
"締付ﾄﾙｸ 10N･m",
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:1",
"付属NUT",
"付属NUT",
"付属NUT"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｼｬｯﾀｰ開閉ｼﾘﾝﾀﾞｰ部組立-①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ開閉ｼﾘﾝﾀﾞｰ部組立-②",
"WorkItems": [
"◆1. GUIDE WASHER SPRING に㉖を塗布する",
"2. ③の付属NUTを取り外す(2個)",
"3. 2完成品にGUIDE WASHER を挿入する",
"4. ③の付属NUTを再度取付ける",
"5. 4完成品にSPRING を挿入する"
],
"WorkPoints": [
"GUIDE の全周に塗布する事",
"WASHER の両面に㉖を塗布する事",
"付属NUT",
"付属NUT",
"付属NUTの1個/2個中は廃棄して下さい",
"SPRING の両面に㉖を塗布する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:1",
"ｸﾞﾘｰｽ塗布 米粒:1",
"ｸﾞﾘｰｽ塗布 米粒:2"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆:1米粒:1米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ開閉ｼﾘﾝﾀﾞｰ部組立-③",
"WorkItems": [
"◆1. WASHER に㉖を塗布する",
"2. 1完成品を②に挿入し③を仮付けする"
],
"WorkPoints": [
"WASHER の片面のみに㉖を塗布する事",
"WASHER の㉖塗布面をシリンダー側に向けて取付ける事",
"本締工程:SD-A052314-007"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼﾘﾝﾀﾞｰﾌﾞﾛｯｸ保持治具",
"Size": "",
"ToolOther": "FM-3087",
"WorkName": "ｼｬｯﾀｰ開閉ｼﾘﾝﾀﾞｰ部組立-④",
"WorkItems": [],
"WorkPoints": [
"NUTを固定して調整する事"
],
"Tolks": [
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "WETE-G002-C10",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"FM-3087",
"WETE-G002-C10"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-3087",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C10",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ開閉ｼﾘﾝﾀﾞｰ部組立-④",
"WorkItems": [],
"WorkPoints": [
"NUTを固定して調整する事"
],
"Tolks": [
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"FM-3087",
"WETE-G002-C10"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "校正対象外",
"StdVal": "0.1㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C10",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "5.5㎜",
"ToolOther": "1.2N･m",
"WorkName": "ｼｬｯﾀｰ開閉ｼﾘﾝﾀﾞｰ部組立-④",
"WorkItems": [],
"WorkPoints": [
"NUTを固定して調整する事"
],
"Tolks": [
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"FM-3087"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"Size": "",
"ToolOther": "FM-2169",
"WorkName": "ｼｬｯﾀｰ開閉ｼﾘﾝﾀﾞｰ部組立-⑤",
"WorkItems": [],
"WorkPoints": [
"取付位置に注意する事",
"取付位置に注意する事",
"取付位置に注意する事",
"取付位置に注意する事"
],
"Tolks": [],
"InspectionNo": "WETE-G002-C10",
"InspectionItems": [
"検査表①:ｼｬｯﾀｰ用ｼﾘﾝﾀﾞｰﾘﾐｯﾄｽｲｯﾁ調整",
"検査表①:ｼｬｯﾀｰ用ｼﾘﾝﾀﾞｰﾘﾐｯﾄｽｲｯﾁ調整",
"検査表①:ｼｬｯﾀｰ用ｼﾘﾝﾀﾞｰﾘﾐｯﾄｽｲｯﾁ調整",
"検査表①:ｼｬｯﾀｰ用ｼﾘﾝﾀﾞｰﾘﾐｯﾄｽｲｯﾁ調整"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"WETE-G002-C10"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2169",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C10",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ開閉ｼﾘﾝﾀﾞｰ部組立-⑤",
"WorkItems": [
"4. 戻限側のｾﾝｻｰｽﾄﾛｰｸ調整を行う",
"3. 出限ｾﾝｻｰをｾﾝﾀｰ位置で固定する",
"2. 出限側のｾﾝｻｰｽﾄﾛｰｸ調整を行う",
"5. 戻限ｾﾝｻｰをｾﾝﾀｰ位置で固定する",
"1. ①に付属ｾﾝｻｰを取付ける"
],
"WorkPoints": [
"NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"ﾒｰｶｰﾗﾍﾞﾙがある面(裏面)に取付ること",
"左側より近づけONしてから1.5㎜の位置に取付ける",
"取付位置に注意する事",
"出限側に治具を繋ぎｼﾘﾝﾀﾞｰを伸ばしON領域にﾏｰｷﾝｸﾞする",
"戻限側に治具を繋ぎｼﾘﾝﾀﾞｰを縮めON領域にﾏｰｷﾝｸﾞする",
"右側より近づけONしてから1.5㎜の位置に取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m",
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "WETE-G002-C10",
"InspectionItems": [
"検査表①:ｼｬｯﾀｰ用ｼﾘﾝﾀﾞｰﾘﾐｯﾄｽｲｯﾁ調整",
"検査表①:ｼｬｯﾀｰ用ｼﾘﾝﾀﾞｰﾘﾐｯﾄｽｲｯﾁ調整"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"⇧ＬＳ調整位置（センター）",
"SMC● CHINA",
"戻限",
"出限",
"出限側 : B02 / 12R",
"戻限側 : B01 / 11R",
"ＬＳ調整位置（センター）⇩",
"ｼﾘﾝﾀﾞｰ戻限用LS(B01/11R)",
"ｼﾘﾝﾀﾞｰ出限用LS(B02/12R)",
"約1.5㎜",
"SMC● MAX0.7 CHINA",
"6-20-CDV7",
"CDU6",
"WETE-G002-C10"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｾﾝｻｰ位置が指示通りである事",
"Method": "目視",
"RecordMethod": "WETE-G002-C10",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "ﾏｲﾅｽ1.6㎜",
"ToolOther": "10cN･m",
"WorkName": "ｼｬｯﾀｰ開閉ｼﾘﾝﾀﾞｰ部組立-⑤",
"WorkItems": [],
"WorkPoints": [
"取付位置に注意する事",
"取付位置に注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:ｼｬｯﾀｰ用ｼﾘﾝﾀﾞｰﾘﾐｯﾄｽｲｯﾁ調整",
"検査表①:ｼｬｯﾀｰ用ｼﾘﾝﾀﾞｰﾘﾐｯﾄｽｲｯﾁ調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ開閉ｼﾘﾝﾀﾞｰ部組立-⑤",
"WorkItems": [],
"WorkPoints": [
"取付位置に注意する事",
"取付位置に注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:ｼｬｯﾀｰ用ｼﾘﾝﾀﾞｰﾘﾐｯﾄｽｲｯﾁ調整",
"検査表①:ｼｬｯﾀｰ用ｼﾘﾝﾀﾞｰﾘﾐｯﾄｽｲｯﾁ調整"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ開閉ｼﾘﾝﾀﾞｰ部組立-⑥",
"WorkItems": [
"2. 1完成品にPLATE PLATE をBOLT で取付ける",
"◆1. ①のベアリングに㉖を塗布する"
],
"WorkPoints": [
"①PLATE PLATE の側面を合わせて取付ける事",
"側面を合わせる事",
"㉖に塗布する事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各1"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｼｬｯﾀｰ開閉ｼﾘﾝﾀﾞｰ部組立-⑥",
"WorkItems": [
"2. 1完成品にPLATE PLATE をBOLT で取付ける"
],
"WorkPoints": [
"①PLATE PLATE の側面を合わせて取付ける事",
"側面を合わせる事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾗｹｯﾄﾋﾟﾝ圧入治具",
"Size": "",
"ToolOther": "FM-4532",
"WorkName": "ｸﾗﾝﾌﾟﾚﾊﾞｰ部組立-①",
"WorkItems": [
"1. BRACKET にPIN を圧入する"
],
"WorkPoints": [
"PIN 割ﾋﾟﾝの方向は規定しない",
"BRACKET のﾀｯﾌﾟ無し箇所にPIN を圧入する事",
"ﾀｯﾌﾟ無し"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4532",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｸﾗﾝﾌﾟﾚﾊﾞｰ部組立-①",
"WorkItems": [
"2. 1完成品にLEVER をBOLT で取付ける"
],
"WorkPoints": [
"確実に圧入されている事",
"LEVER ﾚﾊﾞｰを割ﾋﾟﾝに挿入して取付ける事",
"LEVER を治具のPINに当付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "1.5N･m",
"WorkName": "ｸﾗﾝﾌﾟﾚﾊﾞｰ部組立-①",
"WorkItems": [
"3. 2完成品にBOLT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾚﾊﾞｰ部組立-②",
"WorkItems": [
"◆1. ①に㉖を塗布する",
"3. ①にPLATE WASHER をBOLT WASHER で取付ける",
"◆2. WASHER に㉖を塗布する"
],
"WorkPoints": [
"㉖を青色部（外周）に塗布する事",
"㉖を下記青色部に塗布する事",
"①PLATE がｽﾑｰｽﾞに摺動する事",
"PLATE の取付方向に注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 米粒:2",
"内側にも塗布の事"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:各2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｸﾗﾝﾌﾟﾚﾊﾞｰ部組立-②",
"WorkItems": [
"3. ①にPLATE WASHER をBOLT WASHER で取付ける"
],
"WorkPoints": [
"PLATE の取付方向に注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟﾚﾊﾞｰ部組立-③",
"WorkItems": [
"◆1. SHAFT BUSH LEVER に㉖を塗布する",
"3. 2完成品をBOLT WASHER で固定する",
"2. ④にBUSH LEVER をSHAFT で取付ける"
],
"WorkPoints": [
"青色部に㉖を塗布する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:4"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:4",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｸﾗﾝﾌﾟﾚﾊﾞｰ部組立-③",
"WorkItems": [
"3. 2完成品をBOLT WASHER で固定する",
"2. ④にBUSH LEVER をSHAFT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "194cN･m",
"WorkName": "ｸﾗﾝﾌﾟﾚﾊﾞｰ部組立-③",
"WorkItems": [
"3. 2完成品をBOLT WASHER で固定する",
"2. ④にBUSH LEVER をSHAFT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "40cN･m",
"WorkName": "ｸﾗﾝﾌﾟﾚﾊﾞｰ部組立-④",
"WorkItems": [
"1. ①にSENSOR をBOLT WASHER WASHER で取付ける",
"2. 1完成品にCLIP をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "WETE-G002-C10",
"InspectionItems": [
"検査表①:ﾌｫﾄｾﾝｻｰの締付ﾄﾙｸ"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "ｸﾗﾝﾌﾟﾚﾊﾞｰ部組立-④",
"WorkItems": [
"1. ①にSENSOR をBOLT WASHER WASHER で取付ける",
"2. 1完成品にCLIP をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:ﾌｫﾄｾﾝｻｰの締付ﾄﾙｸ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｸﾗﾝﾌﾟ部組立-①",
"WorkItems": [
"1. WASHER SPACER LEVER LEVER BEARING をBOLT WASHER で取付ける"
],
"WorkPoints": [
"挿入順番と向きに注意する事",
"BEARING ﾍﾞｱﾘﾝｸﾞがｽﾑｰｽﾞに回転する事",
"SPACER Dｶｯﾄの取付位置は特に規定しない"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｸﾗﾝﾌﾟ部組立-②",
"WorkItems": [
"2. 1完成品を①にBOLT WASHER で取付ける",
"◆1. BRACKET にSHAFT を挿入する"
],
"WorkPoints": [
"取付穴",
"SHAFT 青色部に㉙を塗布する事",
"取付向きに注意する事",
"SHAFT Dｶｯﾄの位置は特に規定しない",
"ﾍﾞｱﾘﾝｸﾞがｽﾑｰｽﾞに回転する事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｸﾗﾝﾌﾟ部組立-②",
"WorkItems": [
"2. 1完成品を①にBOLT WASHER で取付ける"
],
"WorkPoints": [
"取付穴",
"取付向きに注意する事",
"SHAFT Dｶｯﾄの位置は特に規定しない",
"ﾍﾞｱﾘﾝｸﾞがｽﾑｰｽﾞに回転する事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾌﾟﾚｰﾄ部組立-①",
"WorkItems": [
"2. 1完成品にPIN PIN を圧入する",
"1. BASE の部品取付け面の確認を行う"
],
"WorkPoints": [
"PIN PIN の出代に注意して圧入する事",
"PIN PIN出代: 5㎜",
"PIN PIN出代: 11㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕､傷等無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍﾞｰｽ､Dﾋﾟﾝ圧入治具",
"Size": "",
"ToolOther": "FM-2254",
"WorkName": "昇降ﾌﾟﾚｰﾄ部組立-①",
"WorkItems": [
"2. 1完成品にPIN PIN を圧入する",
"1. BASE の部品取付け面の確認を行う"
],
"WorkPoints": [
"PIN PIN の出代に注意して圧入する事",
"PIN PIN出代: 5㎜",
"PIN PIN出代: 11㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2254",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降ﾌﾟﾚｰﾄ部組立-①",
"WorkItems": [
"2. 1完成品にPIN PIN を圧入する",
"1. BASE の部品取付け面の確認を行う"
],
"WorkPoints": [
"PIN PIN の出代に注意して圧入する事",
"PIN PIN出代: 5㎜",
"PIN PIN出代: 11㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "昇降ﾌﾟﾚｰﾄ部組立-②",
"WorkItems": [],
"WorkPoints": [
"取付方向に注意する事",
"取付方向に注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "昇降ﾌﾟﾚｰﾄ部組立-②",
"WorkItems": [],
"WorkPoints": [
"取付方向に注意する事",
"取付方向に注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "昇降ﾌﾟﾚｰﾄ部組立-③",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"BRACKET の取付方向に注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"①底面"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "昇降ﾌﾟﾚｰﾄ部組立-④",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"②の取付位置に注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"①上面"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "昇降ﾌﾟﾚｰﾄ部組立-⑤",
"WorkItems": [],
"WorkPoints": [
"ｸﾗﾝﾌﾟﾚﾊﾞｰのﾍﾞｱﾘﾝｸﾞと①のﾋﾟﾝと平行に当付いている事(水色線部)",
"青色部に㉚を塗布する事",
"SPRING の先端の向きは左記の様に引っ掛ける",
"ﾚﾊﾞｰを内側の状態で確認する事",
"クランパーのベアリング部と㉚に隙間が無い事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "昇降ﾌﾟﾚｰﾄ部組立-⑤",
"WorkItems": [],
"WorkPoints": [
"ｸﾗﾝﾌﾟﾚﾊﾞｰのﾍﾞｱﾘﾝｸﾞと①のﾋﾟﾝと平行に当付いている事(水色線部)",
"青色部に㉚を塗布する事",
"SPRING の先端の向きは左記の様に引っ掛ける",
"ﾚﾊﾞｰを内側の状態で確認する事",
"クランパーのベアリング部と㉚に隙間が無い事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｸﾗﾝﾊﾟ組立治具",
"Size": "",
"ToolOther": "FM-2231",
"WorkName": "昇降ﾌﾟﾚｰﾄ部組立-⑤",
"WorkItems": [],
"WorkPoints": [
"ｸﾗﾝﾌﾟﾚﾊﾞｰのﾍﾞｱﾘﾝｸﾞと①のﾋﾟﾝと平行に当付いている事(水色線部)",
"青色部に㉚を塗布する事",
"SPRING の先端の向きは左記の様に引っ掛ける",
"ﾚﾊﾞｰを内側の状態で確認する事",
"クランパーのベアリング部と㉚に隙間が無い事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "WETE-G002-C10",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業",
"WETE-G002-C10"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2231",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C10",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "昇降ﾌﾟﾚｰﾄ部組立-⑤",
"WorkItems": [],
"WorkPoints": [
"ｸﾗﾝﾌﾟﾚﾊﾞｰのﾍﾞｱﾘﾝｸﾞと①のﾋﾟﾝと平行に当付いている事(水色線部)",
"青色部に㉚を塗布する事",
"SPRING の先端の向きは左記の様に引っ掛ける",
"ﾚﾊﾞｰを内側の状態で確認する事",
"クランパーのベアリング部と㉚に隙間が無い事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業",
"WETE-G002-C10"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜ﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C10",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾌﾟﾚｰﾄ部組立-⑤",
"WorkItems": [
"1. ①のｸﾗﾝﾌﾟ部のﾍﾞｱﾘﾝｸﾞ位置(隙間)を確認する",
"◆2. 1完成品に㉚を塗布し、SPRING を引っ掛ける"
],
"WorkPoints": [
"ｸﾗﾝﾌﾟﾚﾊﾞｰのﾍﾞｱﾘﾝｸﾞと①のﾋﾟﾝと平行に当付いている事(水色線部)",
"青色部に㉚を塗布する事",
"SPRING の先端の向きは左記の様に引っ掛ける",
"ﾚﾊﾞｰを内側の状態で確認する事",
"クランパーのベアリング部と㉚に隙間が無い事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"①底面",
"ｸﾞﾘｰｽ塗布 米粒:各1",
"①上面",
"検査表①:ｸﾗﾝﾊﾟｰ隙間確認"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ﾌﾟﾚｰﾄ部組立-⑥",
"WorkItems": [
"1. ①に②をSPACER WASHER ､BOLT WASHER で仮付けする"
],
"WorkPoints": [
"はじめにSPACER WASHER を①にｾｯﾄする事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"仮止め:SD-A052314-037にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立",
"WorkItems": [
"1. BRACKET の部品取付け面の確認を行う",
"2. BRACKET にCLIP をBOLT で取付ける"
],
"WorkPoints": [
"緑色部の面に打痕･ｷｽﾞ等無い事",
"緑色部の面に打痕･ｷｽﾞ等無い事",
"両面に打痕･ｷｽﾞ等無い事",
"BRACKET の表裏に注意する事",
"CLIP の向きに注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"表 面"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕､傷等無き事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄ組立",
"WorkItems": [
"1. BRACKET の部品取付け面の確認を行う",
"2. BRACKET にCLIP をBOLT で取付ける"
],
"WorkPoints": [
"緑色部の面に打痕･ｷｽﾞ等無い事",
"緑色部の面に打痕･ｷｽﾞ等無い事",
"両面に打痕･ｷｽﾞ等無い事",
"BRACKET の表裏に注意する事",
"CLIP の向きに注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"表 面"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄへ昇降ｼﾘﾝﾀﾞｰ取付",
"WorkItems": [
"1. ③の付属NUTを取り外し､①にBOLT で取付ける"
],
"WorkPoints": [
"付属NUT",
"･付属NUTは廃棄し無い事･③の取付向きに注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄへ昇降ｼﾘﾝﾀﾞｰ取付",
"WorkItems": [
"2. 1完成品に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"②の取付向きに注意する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "昇降ｽﾗｲﾄﾞ部本体取付-①",
"WorkItems": [
"2. ①に②STOPPER を仮付けする",
"3. 2完成品にLINEAR-WAY をBOLT で取付ける",
"◆1. STOPPER のナット部に㉛を塗布する",
"◆4. 3完成品のレール部に㉛を塗布する"
],
"WorkPoints": [
"底面より6㎜の位置に仮付けする",
"①とLINEAR-WAY 基準面を合わせる事(黄色点線部に㉜が入ら無い事）",
"LINEAR-WAY の鋼球飛び出しに注意する事 (ﾎﾞﾙﾄ締付時注意)",
"青色部に㉛を塗布する事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"6㎜",
"ｸﾞﾘｰｽ塗布 小豆:各1",
"ｸﾞﾘｰｽ塗布 米粒:3",
"仮止め:SD-A052314-032にて本締め"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:3小豆:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "昇降ｽﾗｲﾄﾞ部本体取付-①",
"WorkItems": [
"2. ①に②STOPPER を仮付けする",
"◆4. 3完成品のレール部に㉛を塗布する"
],
"WorkPoints": [
"底面より6㎜の位置に仮付けする",
"青色部に㉛を塗布する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"6㎜",
"ｸﾞﾘｰｽ塗布 小豆:各1",
"仮止め:SD-A052314-032にて本締め",
"◆作業者安全作業"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "昇降ｽﾗｲﾄﾞ部本体取付-①",
"WorkItems": [
"3. 2完成品にLINEAR-WAY をBOLT で取付ける"
],
"WorkPoints": [
"①とLINEAR-WAY 基準面を合わせる事(黄色点線部に㉜が入ら無い事）",
"LINEAR-WAY の鋼球飛び出しに注意する事 (ﾎﾞﾙﾄ締付時注意)"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "昇降ｽﾗｲﾄﾞ部本体取付-①",
"WorkItems": [
"3. 2完成品にLINEAR-WAY をBOLT で取付ける"
],
"WorkPoints": [
"①とLINEAR-WAY 基準面を合わせる事(黄色点線部に㉜が入ら無い事）",
"LINEAR-WAY の鋼球飛び出しに注意する事 (ﾎﾞﾙﾄ締付時注意)"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "昇降ｽﾗｲﾄﾞ部本体取付-②",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾍｯﾄﾞｵﾌﾟｼｮﾝ駆動ﾕﾆｯﾄ組立台",
"Size": "",
"ToolOther": "FM-6361",
"WorkName": "ﾍﾞｰｽ部、昇降ﾌﾟﾚｰﾄ部ﾄﾞｯｷﾝｸﾞ",
"WorkItems": [
"1. ①に②をBOLT で仮取付ける",
"2. 1完成品を㉗に設置し固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"仮止め:SD-A052314-032にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6361",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ部、昇降ﾌﾟﾚｰﾄ部ﾄﾞｯｷﾝｸﾞ",
"WorkItems": [
"1. ①に②をBOLT で仮取付ける",
"2. 1完成品を㉗に設置し固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"仮止め:SD-A052314-032にて本締め"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾁｪﾝｼﾞｬｰ開閉ｼｬｯﾀｰﾊﾞﾙﾌﾞ配管",
"WorkItems": [
"3. 2完成品の配管を㉘で固定する（2箇所）",
"2. ｶｯﾄしたTUBE を①のﾊﾞﾙﾌﾞに挿入する"
],
"WorkPoints": [
"JOINTとﾏｳﾝﾄに固定する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾁｪﾝｼﾞｬｰ昇降ｼﾘﾝﾀﾞｰﾊﾞﾙﾌﾞ配管",
"WorkItems": [
"1. TUBE を指定寸法にｶｯﾄする",
"2. ｶｯﾄした配管を①の各々JOINTに挿入する"
],
"WorkPoints": [
"№202 : 240㎜にｶｯﾄする",
"№203 : 200㎜にｶｯﾄする",
"№204 : 200㎜にｶｯﾄする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"№202",
"№204",
"№203"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ検査治具",
"Size": "",
"ToolOther": "FM-6229",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ検査治具接続-①",
"WorkItems": [
"1. ㉖の電源を投入する"
],
"WorkPoints": [
"手順1:POWERをONする",
"手順2:ﾓﾆﾀｰの指示に従いSTART SWを押す",
"ｾｯﾄｱｯﾌﾟ完了です",
"指の挟み込みに注意して検査を実施してください"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6229",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ検査治具",
"Size": "",
"ToolOther": "FM-6229",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ検査治具接続-②",
"WorkItems": [
"1. ①に㉖の各センサーを接続する",
"2. ①に㉖の配管を各バルブに接続する"
],
"WorkPoints": [
"ｼｬｯﾀｰ開閉ｾﾝｻｰ(開:B01P､閉:B02P)",
"ﾁｪﾝｼﾞｬｰ有無ｾﾝｻｰ(B03R)",
"ﾁｪﾝｼﾞｬｰ昇降ｾﾝｻｰ(上昇:B04R､下降:B05R)",
"ｼｬｯﾀｰﾊﾞﾙﾌﾞ(R4091R)",
"ﾁｪﾝｼﾞｬｰ昇降ﾊﾞﾙﾌﾞ(R4092R)",
"ｼｬｯﾀｰﾊﾞﾙﾌﾞと昇降ﾊﾞﾙﾌﾞにそれぞれ接続する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"昇降ﾊﾞﾙﾌﾞ",
"ｼｬｯﾀｰﾊﾞﾙﾌﾞへ",
"B03R",
"B04R",
"B01P",
"B02P",
"R4091R",
"B05R",
"R4092R"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-6229",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.