input stringclasses 1 value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "正流れﾚｰﾝ2固定側ﾌｧｲﾊﾞｰ引き回し1",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰ線を引き回し固定する",
"2. 1完成品にCABLE を接続し整線する"
],
"WorkPoints": [
"⑦黄色ﾏｰｷﾝｸﾞ位置で固定",
"④⑤黄色ﾏｰｷﾝｸﾞ位置で固定",
"B124",
"B123",
"Rを保ちﾎﾞﾙﾄから回避する事"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C03",
"InspectionItems": [
"検査表①:ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WEPJ-G002-C03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "正流れﾚｰﾝ2固定側ﾌｧｲﾊﾞｰ引き回し2",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰ線を引き回し固定する"
],
"WorkPoints": [
"①黄色ﾏｰｷﾝｸﾞ位置で固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回が出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "逆流れﾚｰﾝ2固定側ﾌｧｲﾊﾞｰ引き回し",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰｾﾝｻｰを引き回す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ2",
"125mm"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回が出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "逆流れﾚｰﾝ2固定側ﾌｧｲﾊﾞｰ引き回し",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰｾﾝｻｰを引き回す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ2",
"125mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP:ｽﾗｲﾄﾞ搬送仕様】ﾚｰﾝ2固定側ﾌｧｲﾊﾞｰｾﾝｻ引き回し",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰｾﾝｻｰを引き回す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回が出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "45cN･m",
"WorkName": "ﾚｰﾝ2可動側ﾌｧｲﾊﾞｰｾﾝｻ取付け",
"WorkItems": [
"1. ①に②③⑥をBOLT WASHER BOLT WASHER で取付ける"
],
"WorkPoints": [
"ｽﾗｲﾄﾞ搬送OP",
"⑥ｽﾗｲﾄﾞ搬送OP仕様･正流れ⑧⑨に取付け･逆流れ⑧⑨に取付け",
"③通常仕様･正流れ④⑤に取付け･逆流れ⑧⑨に取付け",
"※ｽﾗｲﾄﾞ搬送OP仕様時の流れ変更はｿﾌﾄで切替える為､組替えない",
"ｽﾗｲﾄﾞ搬送OP"
],
"Tolks": [
"締付ﾄﾙｸ 45cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾏｰｷﾝｸﾞ参考図",
"(50㎜)",
"ﾚｰﾝ1",
"ﾚｰﾝ2"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "45cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "正流れﾚｰﾝ2可動側ﾌｧｲﾊﾞｰ引き回し1",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰ線を引き回し固定する"
],
"WorkPoints": [
"①黄色ﾏｰｷﾝｸﾞ位置で固定",
"④⑤黄色ﾏｰｷﾝｸﾞ位置がｾﾝｻｰの下に来るように固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回が出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "正流れﾚｰﾝ2可動側ﾌｧｲﾊﾞｰ引き回し2",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰ線を引き回し固定する"
],
"WorkPoints": [
"⑦黄色ﾏｰｷﾝｸﾞ位置がﾎﾞﾙﾄの中心に来るように固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回が出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾚｰﾝ2可動側ﾌｧｲﾊﾞｰﾀﾞｸﾄｶﾊﾞｰ取付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾌｧｲﾊﾞｰ線を挟まないように注意",
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m",
"1. ①に②を⑯で取付ける",
"ﾌｧｲﾊﾞｰ線を挟まないように注意",
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m",
"1. ①に②を⑯で取付ける",
"ﾌｧｲﾊﾞｰ線を挟まないように注意",
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m",
"1. ①に②を⑯で取付ける"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2可動側ﾋﾟﾝ残検出配線接続",
"WorkItems": [
"1. ①にCABLE を接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C03",
"InspectionItems": [
"検査表①:ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"WEPJ-G002-C03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2可動側右側ﾍﾞｱ整線1",
"WorkItems": [
"1. ①のﾌｧｰﾊﾞｰを③(3連ﾁｭｰﾌﾞ)に通す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ2",
"ﾚｰﾝ1"
]
} | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2可動側右側ﾍﾞｱ整線2",
"WorkItems": [
"1. CABLE-VEYOR の蓋を開け①の配線を入れる",
"2. 1完成品に3連ﾁｭｰﾌﾞを入れる"
],
"WorkPoints": [
"配線のねじれ無き事",
"蓋を閉める(ｶﾁｯと音がするまで)",
"向きに注意(凹側)",
"配線のねじれ無き事",
"ｹｰﾌﾞﾙﾍﾞｱ内配置(ﾚｰﾝ2側正面より)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M621",
"B125",
"M621"
]
} | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP】ｽﾗｲﾄﾞ搬送ﾚｰﾝ2可動側右側ﾍﾞｱ整線1",
"WorkItems": [
"1. ②に①のﾌｧｰﾊﾞｰを通す"
],
"WorkPoints": [
"ｽﾗｲﾄﾞ搬送OP",
"標準時の配管(5連)を使用の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ2",
"ﾚｰﾝ1"
]
} | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "【OP】ｽﾗｲﾄﾞ搬送ﾚｰﾝ2可動側右側ﾍﾞｱ整線2",
"WorkItems": [
"1. ③の蓋を開け①の配線を入れる",
"2. 1完成品に5連ﾁｭｰﾌﾞを入れる"
],
"WorkPoints": [
"配線のねじれ無き事",
"蓋を閉める(ｶﾁｯと音がするまで)",
"向きに注意(凹側)",
"配線のねじれ無き事",
"ｹｰﾌﾞﾙﾍﾞｱ内配置(ﾚｰﾝ2側正面より)",
"⑨⑧③②①",
"ｽﾗｲﾄﾞ搬送OP"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M621",
"B125",
"M621"
]
} | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ﾚｰﾝ2可動側右側ﾍﾞｱ整線2",
"WorkItems": [
"3. ｱｰｽ線をSCREW で固定する",
"2. ﾌｧｲﾊﾞｰ線､配線を固定する",
"1. ⑤のｹｰﾌﾞﾙﾍﾞｱの上側を取付ける"
],
"WorkPoints": [
"FGCVM4",
"FGCVM6",
"ｱｰｽ線の噛み込みに注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "WEPJ-G002-C03",
"InspectionItems": [
"検査表SCREW :FG線接続確認"
],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2可動側右側ﾍﾞｱ整線3",
"WorkItems": [
"2. ｹｰﾌﾞﾙﾍﾞｱの下側を取付け配線を固定する",
"1. ①のｹｰﾌﾞﾙﾍﾞｱ内の配線を固定する"
],
"WorkPoints": [
"通してあるｲﾝｼｭﾛｯｸにて固定",
"ｹｰﾌﾞﾙﾍﾞｱ内に配管､配線にゆとりがある事",
"ﾁｭｰﾌﾞの位置で固定されている事",
"ﾁｭｰﾌﾞの位置で固定されている事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2可動側左側ﾍﾞｱ整線1",
"WorkItems": [
"1. TUBE に①ﾌｧｰﾊﾞｰを通す",
"3. 2完成品に5連ﾁｭｰﾌﾞを入れる",
"2. CABLE-VEYOR の蓋を開け配線を入れる"
],
"WorkPoints": [
"配線のねじれ無き事",
"蓋を閉める(ｶﾁｯと音がするまで)",
"向きに注意(凹側)",
"配線のねじれ無き事",
"ｹｰﾌﾞﾙﾍﾞｱ内配置(正面より)",
"④⑤⑥⑦",
"⑦⑥⑤④"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M627",
"M625",
"M627",
"M625",
"ﾚｰﾝ2",
"ﾚｰﾝ1"
]
} | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ﾚｰﾝ2可動側左側ﾍﾞｱ整線2",
"WorkItems": [
"3. ｱｰｽ線をSCREW で固定する",
"2. ﾌｧｲﾊﾞｰ線､配線を固定する",
"1. ⑤のｹｰﾌﾞﾙﾍﾞｱの上側を取付ける"
],
"WorkPoints": [
"FGCVM5",
"ｱｰｽ線の噛み込みに注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "WEPJ-G002-C03",
"InspectionItems": [
"検査表SCREW :FG線接続確認"
],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2可動側左側ﾍﾞｱ整線3",
"WorkItems": [
"2. ｹｰﾌﾞﾙﾍﾞｱの下側を取付け配線を固定する",
"1. ①のｹｰﾌﾞﾙﾍﾞｱ内の配線を固定する"
],
"WorkPoints": [
"ﾁｭｰﾌﾞの位置で固定されている事",
"ﾁｭｰﾌﾞの位置で固定されている事",
"通してあるｲﾝｼｭﾛｯｸにて固定",
"ｹｰﾌﾞﾙﾍﾞｱ内に配管､配線にゆとりがある事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ1固定側ﾏｰｸﾁｭｰﾌﾞ挿入",
"WorkItems": [
"1. ﾌｧｲﾊﾞｰ線にMARK TUBE MARK TUBE を挿入する"
],
"WorkPoints": [
"⑧⑨ｽﾗｲﾄﾞ搬送OP"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"MARK TUBE ",
"ﾚｰﾝ1",
"MARK TUBE ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ2"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2固定側ﾏｰｸﾁｭｰﾌﾞ挿入",
"WorkItems": [
"1. ﾌｧｲﾊﾞｰ線にMARK TUBE MARK TUBE を挿入する"
],
"WorkPoints": [
"⑧⑨ｽﾗｲﾄﾞ搬送OP"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"MARK TUBE ",
"ﾚｰﾝ1",
"MARK TUBE ",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ2"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ1可動側ﾏｰｸﾁｭｰﾌﾞ挿入",
"WorkItems": [
"1. ﾌｧｲﾊﾞｰ線にMARK TUBE MARK TUBE を挿入する"
],
"WorkPoints": [
"⑧⑨ｽﾗｲﾄﾞ搬送OP"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ2",
"MARK TUBE ",
"MARK TUBE "
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2可動側ﾏｰｸﾁｭｰﾌﾞ挿入",
"WorkItems": [
"1. ﾌｧｲﾊﾞｰ線にMARK TUBE MARK TUBE を挿入する"
],
"WorkPoints": [
"⑧⑨ｽﾗｲﾄﾞ搬送OP"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"MARK TUBE ",
"ﾚｰﾝ1",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ2",
"MARK TUBE "
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側配線ﾌﾞﾗｹｯﾄ可動ﾌｧｲﾊﾞｰ整線",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰ線を整線する"
],
"WorkPoints": [
"Rを保ち余裕がある事",
"Rを保ち余裕がある事",
"通してあるｲﾝｼｭﾛｯｸにて固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側配線ﾌﾞﾗｹｯﾄ固定ﾌｧｲﾊﾞｰ整線",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰ線を整線する"
],
"WorkPoints": [
"Rを保ち余裕が作る",
"Rを保ち余裕を作る",
"通してあるｲﾝｼｭﾛｯｸにて固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2"
]
} | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側配線ﾌﾞﾗｹｯﾄ可動ﾌｧｲﾊﾞｰ整線",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰ線を整線する"
],
"WorkPoints": [
"通してあるｲﾝｼｭﾛｯｸにて固定",
"Rを保ち余裕を作る",
"Rを保ち余裕を作る"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側配線ﾌﾞﾗｹｯﾄ固定ﾌｧｲﾊﾞｰ整線",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰ線を整線する"
],
"WorkPoints": [
"Rを保ち余裕が作る",
"Rを保ち余裕を作る",
"通してあるｲﾝｼｭﾛｯｸにて固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2"
]
} | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側ﾌｧｲﾊﾞｰ線接続",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰ線をｱﾝﾌﾟに接続する"
],
"WorkPoints": [
"付属のﾌｧｲﾊﾞｰｶｯﾀｰでｶｯﾄして接続する",
"ｽﾗｲﾄﾞ搬送OP",
"上段:可動側(黄)",
"下段:固定側(白)",
"ﾌｧｲﾊﾞｰ線を奥まで挿入する事",
"ﾌｧｲﾊﾞｰﾛｯｸﾚﾊﾞｰがﾛｯｸされている事"
],
"Tolks": [],
"InspectionNo": "WEJPJ-G002-C03",
"InspectionItems": [
"検査表①:光ﾌｧｲﾊﾞｰ接続確認"
],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"B1033B1032B1021B1020",
"B1026B1025B1024B1023B1022",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"WEJPJ-G002-C03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEJPJ-G002-C03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側ﾌｧｲﾊﾞｰ線接続",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰ線をｱﾝﾌﾟに接続する"
],
"WorkPoints": [
"上段:可動側(黄)",
"下段:固定側(白)",
"ﾌｧｲﾊﾞｰ線を奥まで挿入する事",
"ﾌｧｲﾊﾞｰﾛｯｸﾚﾊﾞｰがﾛｯｸされている事",
"付属のﾌｧｲﾊﾞｰｶｯﾀｰでｶｯﾄして接続する"
],
"Tolks": [],
"InspectionNo": "WEJPJ-G002-C03",
"InspectionItems": [
"検査表①:光ﾌｧｲﾊﾞｰ接続確認"
],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"B1132B1133B1122B1123",
"B1124B1125B1126B1120B1122",
"ﾚｰﾝ2",
"ﾚｰﾝ1",
"WEJPJ-G002-C03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEJPJ-G002-C03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側配線整線接続(B126)",
"WorkItems": [
"2. 配線をｾﾝｻに接続する",
"1. ①のﾍﾞｱからの分岐配線(B126R)を引き回す"
],
"WorkPoints": [
"通してあるｲﾝｼｭﾛｯｸにて固定"
],
"Tolks": [],
"InspectionNo": "WEJPJ-G002-C03",
"InspectionItems": [
"検査表①:ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"B4 K323",
"B126R",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WEJPJ-G002-C03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEJPJ-G002-C03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側ｱﾝﾌﾟ配線整線接続",
"WorkItems": [
"1. ⑤にCABLE を引き回ｱﾝﾌﾟに接続する"
],
"WorkPoints": [
"通してあるｲﾝｼｭﾛｯｸにて固定",
"OP仕様でない場合には下記の様に固定する"
],
"Tolks": [],
"InspectionNo": "WEJPJ-G002-C03",
"InspectionItems": [
"検査表CABLE :ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"B1033B1032B1021B1020",
"B1026B1025B1024B1023B1022",
"B1021B1020",
"B1026B1023B1022",
"B1025B1024",
"B1033B1032",
"WEJPJ-G002-C03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEJPJ-G002-C03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側配線整線接続(B122)",
"WorkItems": [
"2. 配線をｾﾝｻに接続する",
"1. ①のﾍﾞｱからの分岐配線(B122R)を引き回す"
],
"WorkPoints": [
"通してあるｲﾝｼｭﾛｯｸにて固定"
],
"Tolks": [],
"InspectionNo": "WEJPJ-G002-C03",
"InspectionItems": [
"検査表①:ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"B4 K324",
"B122R",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WEJPJ-G002-C03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEJPJ-G002-C03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側ｱﾝﾌﾟ配線整線接続",
"WorkItems": [
"1. ⑤にCABLE を引き回ｱﾝﾌﾟに接続する"
],
"WorkPoints": [
"通してあるｲﾝｼｭﾛｯｸにて固定"
],
"Tolks": [],
"InspectionNo": "WEJPJ-G002-C03",
"InspectionItems": [
"検査表CABLE :ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"B1124B1125B1126B1120B1121",
"B1132B1133B1122B1123",
"WEJPJ-G002-C03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEJPJ-G002-C03",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側配線整線(B123、B124)",
"WorkItems": [
"1. ①の配線を引き回固定する"
],
"WorkPoints": [
"通してあるｲﾝｼｭﾛｯｸにて固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "駆動部調整検査治具乗せこみ前準備",
"WorkItems": [
"1. ①駆動部の赤色のﾎﾞﾙﾄをすべて緩める"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C42",
"InspectionItems": [
"検査表①:治具活用前準備"
],
"WorkTypes": [],
"Words": [
"ﾈｼﾞ緩め箇所",
"ﾈｼﾞ緩め箇所",
"WEPJ-G002-C42"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C42",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6626",
"WorkName": "駆動部調整検査治具乗せこみ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替ﾕﾆｯﾄ運搬台車(NPM-GH)",
"Size": "",
"ToolOther": "FM-6630",
"WorkName": "駆動部調整検査治具乗せこみ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6630",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "駆動部調整検査治具乗せこみ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C42",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"WEPJ-G002-C42"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C42",
"Other": "重量物",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6626",
"WorkName": "駆動部側面調整",
"WorkItems": [
"1. ﾌﾞﾛｯｸの取付位置を合わせて､締結"
],
"WorkPoints": [
"ﾋﾟﾝとﾌﾞﾛｯｸの隙間確認(0.03㎜が通ら無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:切替仕様40連仕様駆動部 内袖上部後ﾌﾞﾗｹｯﾄ(X方向)(Y方向)確認",
"確認対象部位",
"側面",
"ﾌﾞﾛｯｸ回転方向",
"②Z方向ｽｷﾏ確認",
"①Y方向ｽｷﾏ確認",
"③Z方向ｽｷﾏ確認",
"ﾈｼﾞ締結箇所"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替ﾕﾆｯﾄ運搬台車(NPM-GH)",
"Size": "",
"ToolOther": "FM-6630",
"WorkName": "駆動部側面調整",
"WorkItems": [
"1. ﾌﾞﾛｯｸの取付位置を合わせて､締結"
],
"WorkPoints": [
"ﾋﾟﾝとﾌﾞﾛｯｸの隙間確認(0.03㎜が通ら無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:切替仕様40連仕様駆動部 内袖上部後ﾌﾞﾗｹｯﾄ(X方向)(Y方向)確認",
"確認対象部位",
"側面",
"ﾌﾞﾛｯｸ回転方向",
"②Z方向ｽｷﾏ確認",
"①Y方向ｽｷﾏ確認",
"③Z方向ｽｷﾏ確認",
"ﾈｼﾞ締結箇所"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6630",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "駆動部側面調整",
"WorkItems": [
"1. ﾌﾞﾛｯｸの取付位置を合わせて､締結"
],
"WorkPoints": [
"ﾋﾟﾝとﾌﾞﾛｯｸの隙間確認(0.03㎜が通ら無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WEPJ-G002-C42",
"InspectionItems": [
"検査表①:切替仕様40連仕様駆動部 内袖上部後ﾌﾞﾗｹｯﾄ(X方向)(Y方向)確認"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"確認対象部位",
"側面",
"ﾌﾞﾛｯｸ回転方向",
"②Z方向ｽｷﾏ確認",
"①Y方向ｽｷﾏ確認",
"③Z方向ｽｷﾏ確認",
"ﾈｼﾞ締結箇所",
"WEPJ-G002-C42"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C42",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "駆動部側面調整",
"WorkItems": [
"1. ﾌﾞﾛｯｸの取付位置を合わせて､締結"
],
"WorkPoints": [
"ﾋﾟﾝとﾌﾞﾛｯｸの隙間確認(0.03㎜が通ら無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:切替仕様40連仕様駆動部 内袖上部後ﾌﾞﾗｹｯﾄ(X方向)(Y方向)確認",
"確認対象部位",
"側面",
"ﾌﾞﾛｯｸ回転方向",
"②Z方向ｽｷﾏ確認",
"①Y方向ｽｷﾏ確認",
"③Z方向ｽｷﾏ確認",
"ﾈｼﾞ締結箇所"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "支持部調整検査治具乗せこみ前準備",
"WorkItems": [
"1. ①支持部の赤色のﾎﾞﾙﾄをすべて緩める"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C44",
"InspectionItems": [
"検査表①:治具活用前準備"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾈｼﾞ緩め箇所",
"ﾈｼﾞ緩め箇所",
"ﾈｼﾞ緩め箇所",
"WEPJ-G002-C44"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C44",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6626",
"WorkName": "支持部調整検査治具乗せこみ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替ﾕﾆｯﾄ運搬台車(NPM-GH)",
"Size": "",
"ToolOther": "FM-6630",
"WorkName": "支持部調整検査治具乗せこみ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6630",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "支持部調整検査治具乗せこみ",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C44",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"WEPJ-G002-C44"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C44",
"Other": "重量物",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6626",
"WorkName": "支持部側面調整",
"WorkItems": [
"1. ①ﾌﾞﾛｯｸの取付位置を合わせて､締結"
],
"WorkPoints": [
"ﾋﾟﾝとﾌﾞﾛｯｸの隙間確認(0.03㎜が通ら無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:切替仕様40連仕様支持部 内袖上部後ﾌﾞﾗｹｯﾄ(Z方向)(Y方向)確認",
"確認対象部位",
"③Y方向ｽｷﾏ確認",
"①Y方向ｽｷﾏ確認",
"➁Z方向スキマ確認",
"ﾌﾞﾛｯｸ回転方向",
"ﾈｼﾞ締結箇所",
"ﾈｼﾞ締結箇所",
"側面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替ﾕﾆｯﾄ運搬台車(NPM-GH)",
"Size": "",
"ToolOther": "FM-6630",
"WorkName": "支持部側面調整",
"WorkItems": [
"1. ①ﾌﾞﾛｯｸの取付位置を合わせて､締結"
],
"WorkPoints": [
"ﾋﾟﾝとﾌﾞﾛｯｸの隙間確認(0.03㎜が通ら無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:切替仕様40連仕様支持部 内袖上部後ﾌﾞﾗｹｯﾄ(Z方向)(Y方向)確認",
"確認対象部位",
"③Y方向ｽｷﾏ確認",
"①Y方向ｽｷﾏ確認",
"➁Z方向スキマ確認",
"ﾌﾞﾛｯｸ回転方向",
"ﾈｼﾞ締結箇所",
"ﾈｼﾞ締結箇所",
"側面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6630",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "支持部側面調整",
"WorkItems": [
"1. ①ﾌﾞﾛｯｸの取付位置を合わせて､締結"
],
"WorkPoints": [
"ﾋﾟﾝとﾌﾞﾛｯｸの隙間確認(0.03㎜が通ら無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "WEPJ-G002-C44",
"InspectionItems": [
"検査表①:切替仕様40連仕様支持部 内袖上部後ﾌﾞﾗｹｯﾄ(Z方向)(Y方向)確認"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"確認対象部位",
"③Y方向ｽｷﾏ確認",
"①Y方向ｽｷﾏ確認",
"➁Z方向スキマ確認",
"ﾌﾞﾛｯｸ回転方向",
"ﾈｼﾞ締結箇所",
"ﾈｼﾞ締結箇所",
"側面",
"WEPJ-G002-C44"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C44",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "支持部側面調整",
"WorkItems": [
"1. ①ﾌﾞﾛｯｸの取付位置を合わせて､締結"
],
"WorkPoints": [
"ﾋﾟﾝとﾌﾞﾛｯｸの隙間確認(0.03㎜が通ら無い事)"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:切替仕様40連仕様支持部 内袖上部後ﾌﾞﾗｹｯﾄ(Z方向)(Y方向)確認",
"確認対象部位",
"③Y方向ｽｷﾏ確認",
"①Y方向ｽｷﾏ確認",
"➁Z方向スキマ確認",
"ﾌﾞﾛｯｸ回転方向",
"ﾈｼﾞ締結箇所",
"ﾈｼﾞ締結箇所",
"側面"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6626",
"WorkName": "調整検査治具取付",
"WorkItems": [
"1. ㉘の治具を取付"
],
"WorkPoints": [
"決して押し付けないように接触させる程度",
"平行ﾋﾟﾝにてX方向に正確に位置決めされるようにｾｯﾄし､ﾉﾌﾞで固定して使用する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替ﾕﾆｯﾄ運搬台車(NPM-GH)",
"Size": "",
"ToolOther": "FM-6630",
"WorkName": "調整検査治具取付",
"WorkItems": [
"1. ㉘の治具を取付"
],
"WorkPoints": [
"決して押し付けないように接触させる程度",
"平行ﾋﾟﾝにてX方向に正確に位置決めされるようにｾｯﾄし､ﾉﾌﾞで固定して使用する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6630",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ(40連専用部)",
"Size": "",
"ToolOther": "FM-6669",
"WorkName": "調整検査治具取付",
"WorkItems": [
"1. ㉘の治具を取付"
],
"WorkPoints": [
"決して押し付けないように接触させる程度",
"平行ﾋﾟﾝにてX方向に正確に位置決めされるようにｾｯﾄし､ﾉﾌﾞで固定して使用する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6669",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6626",
"WorkName": "駆動部支持部調整と検査",
"WorkItems": [],
"WorkPoints": [
"調整後､上図の3か所のﾒｲﾝのﾈｼﾞを本締めする",
"調整は右図の3か所がﾒｲﾝのﾈｼﾞですﾒｲﾝのﾈｼﾞを本締め後､､他のﾈｼﾞを本締めする",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"調整後､上図の3か所のﾒｲﾝのﾈｼﾞを本締めする",
"調整は右図の3か所がﾒｲﾝのﾈｼﾞですﾒｲﾝのﾈｼﾞを本締め後､､他のﾈｼﾞを本締めする",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:切替仕様40連仕様駆動部 台車樹脂ｶﾞｲﾄﾞ位置確認検査(X方向)",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞを本締め後､本締めするﾈｼﾞ",
"検査表①:切替仕様40連仕様駆動部 台車樹脂ｶﾞｲﾄﾞ位置確認検査(X方向)",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞを本締め後､本締めするﾈｼﾞ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替ﾕﾆｯﾄ運搬台車(NPM-GH)",
"Size": "",
"ToolOther": "FM-6630",
"WorkName": "駆動部支持部調整と検査",
"WorkItems": [],
"WorkPoints": [
"調整後､上図の3か所のﾒｲﾝのﾈｼﾞを本締めする",
"調整は右図の3か所がﾒｲﾝのﾈｼﾞですﾒｲﾝのﾈｼﾞを本締め後､､他のﾈｼﾞを本締めする",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"調整後､上図の3か所のﾒｲﾝのﾈｼﾞを本締めする",
"調整は右図の3か所がﾒｲﾝのﾈｼﾞですﾒｲﾝのﾈｼﾞを本締め後､､他のﾈｼﾞを本締めする",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:切替仕様40連仕様駆動部 台車樹脂ｶﾞｲﾄﾞ位置確認検査(X方向)",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞを本締め後､本締めするﾈｼﾞ",
"検査表①:切替仕様40連仕様駆動部 台車樹脂ｶﾞｲﾄﾞ位置確認検査(X方向)",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞを本締め後､本締めするﾈｼﾞ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6630",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ(40連専用部)",
"Size": "",
"ToolOther": "FM-6669",
"WorkName": "駆動部支持部調整と検査",
"WorkItems": [],
"WorkPoints": [
"調整後､上図の3か所のﾒｲﾝのﾈｼﾞを本締めする",
"調整は右図の3か所がﾒｲﾝのﾈｼﾞですﾒｲﾝのﾈｼﾞを本締め後､､他のﾈｼﾞを本締めする",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"調整後､上図の3か所のﾒｲﾝのﾈｼﾞを本締めする",
"調整は右図の3か所がﾒｲﾝのﾈｼﾞですﾒｲﾝのﾈｼﾞを本締め後､､他のﾈｼﾞを本締めする",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:切替仕様40連仕様駆動部 台車樹脂ｶﾞｲﾄﾞ位置確認検査(X方向)",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞを本締め後､本締めするﾈｼﾞ",
"検査表①:切替仕様40連仕様駆動部 台車樹脂ｶﾞｲﾄﾞ位置確認検査(X方向)",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞを本締め後､本締めするﾈｼﾞ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6669",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "駆動部支持部調整と検査",
"WorkItems": [],
"WorkPoints": [
"調整後､上図の3か所のﾒｲﾝのﾈｼﾞを本締めする",
"調整は右図の3か所がﾒｲﾝのﾈｼﾞですﾒｲﾝのﾈｼﾞを本締め後､､他のﾈｼﾞを本締めする",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"調整後､上図の3か所のﾒｲﾝのﾈｼﾞを本締めする",
"調整は右図の3か所がﾒｲﾝのﾈｼﾞですﾒｲﾝのﾈｼﾞを本締め後､､他のﾈｼﾞを本締めする",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "WEPJ-G002-C42",
"InspectionItems": [
"検査表①:切替仕様40連仕様駆動部 台車樹脂ｶﾞｲﾄﾞ位置確認検査(X方向)",
"検査表①:切替仕様40連仕様駆動部 台車樹脂ｶﾞｲﾄﾞ位置確認検査(X方向)"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞを本締め後､本締めするﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞを本締め後､本締めするﾈｼﾞ",
"WEPJ-G002-C42"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C42",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "駆動部支持部調整と検査",
"WorkItems": [],
"WorkPoints": [
"調整後､上図の3か所のﾒｲﾝのﾈｼﾞを本締めする",
"調整は右図の3か所がﾒｲﾝのﾈｼﾞですﾒｲﾝのﾈｼﾞを本締め後､､他のﾈｼﾞを本締めする",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"調整後､上図の3か所のﾒｲﾝのﾈｼﾞを本締めする",
"調整は右図の3か所がﾒｲﾝのﾈｼﾞですﾒｲﾝのﾈｼﾞを本締め後､､他のﾈｼﾞを本締めする",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "WEPJ-G002-C44",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:切替仕様40連仕様駆動部 台車樹脂ｶﾞｲﾄﾞ位置確認検査(X方向)",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞを本締め後､本締めするﾈｼﾞ",
"検査表①:切替仕様40連仕様駆動部 台車樹脂ｶﾞｲﾄﾞ位置確認検査(X方向)",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞを本締め後､本締めするﾈｼﾞ",
"WEPJ-G002-C44"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WEPJ-G002-C44",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "駆動部支持部調整と検査",
"WorkItems": [],
"WorkPoints": [
"調整後､上図の3か所のﾒｲﾝのﾈｼﾞを本締めする",
"調整は右図の3か所がﾒｲﾝのﾈｼﾞですﾒｲﾝのﾈｼﾞを本締め後､､他のﾈｼﾞを本締めする",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"調整後､上図の3か所のﾒｲﾝのﾈｼﾞを本締めする",
"調整は右図の3か所がﾒｲﾝのﾈｼﾞですﾒｲﾝのﾈｼﾞを本締め後､､他のﾈｼﾞを本締めする",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:切替仕様40連仕様駆動部 台車樹脂ｶﾞｲﾄﾞ位置確認検査(X方向)",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞを本締め後､本締めするﾈｼﾞ",
"検査表①:切替仕様40連仕様駆動部 台車樹脂ｶﾞｲﾄﾞ位置確認検査(X方向)",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞを本締め後､本締めするﾈｼﾞ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "駆動部支持部調整と検査",
"WorkItems": [],
"WorkPoints": [
"調整後､上図の3か所のﾒｲﾝのﾈｼﾞを本締めする",
"調整は右図の3か所がﾒｲﾝのﾈｼﾞですﾒｲﾝのﾈｼﾞを本締め後､､他のﾈｼﾞを本締めする",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事",
"樹脂ｶﾞｲﾄﾞにそりがあるのでｶﾞｲﾄﾞの範囲で2点以上もしくはｶﾞｲﾄﾞ中央付近しか接触しない場合は1点ｼｯｸﾈｽｹﾞｰｼﾞ0.1㎜が通ら無い事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表①:切替仕様40連仕様駆動部 台車樹脂ｶﾞｲﾄﾞ位置確認検査(X方向)",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞ",
"ﾒｲﾝのﾈｼﾞを本締め後､本締めするﾈｼﾞ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6626",
"WorkName": "駆動部支持部取り外し",
"WorkItems": [
"1. ①から治具㉘の調整用ブロック（青色）を取り外す",
"2. 駆動部と支持部を治具㉖㉗から取り外す"
],
"WorkPoints": [
"駆動部と支持部を取り外し時に接触するため"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"駆動部",
"支持部"
]
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-6626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替ﾕﾆｯﾄ運搬台車(NPM-GH)",
"Size": "",
"ToolOther": "FM-6630",
"WorkName": "駆動部支持部取り外し",
"WorkItems": [
"1. ①から治具㉘の調整用ブロック（青色）を取り外す",
"2. 駆動部と支持部を治具㉖㉗から取り外す"
],
"WorkPoints": [
"駆動部と支持部を取り外し時に接触するため"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"駆動部",
"支持部"
]
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-6630",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "切替用ﾕﾆｯﾄ組立ｼﾞｸﾞ(40連専用部)",
"Size": "",
"ToolOther": "FM-6669",
"WorkName": "駆動部支持部取り外し",
"WorkItems": [
"1. ①から治具㉘の調整用ブロック（青色）を取り外す"
],
"WorkPoints": [
"駆動部と支持部を取り外し時に接触するため"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-6669",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾀｲﾏｳﾝﾄ取付(Aﾌﾞﾛｯｸ)",
"WorkItems": [
"1. ①に②を取付ける"
],
"WorkPoints": [
"ﾏｳﾝﾄの向き"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"32個",
"15個"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾀｲﾏｳﾝﾄ取付(Bﾌﾞﾛｯｸ)",
"WorkItems": [
"1. ①に②を取付ける"
],
"WorkPoints": [
"ﾏｳﾝﾄの向き",
"ここの4個は裏から"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"16個",
"9個"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾀｲﾏｳﾝﾄ取付(Cﾌﾞﾛｯｸ)",
"WorkItems": [
"1. ①に②を取付ける"
],
"WorkPoints": [
"ﾏｳﾝﾄの向き",
"ここの3個は裏から"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"11個",
"0個"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾀｲﾏｳﾝﾄ取付(Dﾌﾞﾛｯｸ)",
"WorkItems": [
"1. ①に②を取付ける"
],
"WorkPoints": [
"ﾏｳﾝﾄの向き"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1個",
"d矢視図"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾀｲﾏｳﾝﾄ取付(上面)",
"WorkItems": [
"1. ①に②を取付ける"
],
"WorkPoints": [
"ﾏｳﾝﾄの向き"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"3個",
"2個"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上面ｺﾈｸﾀﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①に②を⑯⑰にて取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "上面ｼｰﾄ貼付け",
"WorkItems": [
"1. ①に②を貼付ける"
],
"WorkPoints": [
"25㎜",
"318㎜",
"25㎜",
"223㎜",
"ｹｰﾌﾞﾙﾍﾞｱ取付穴とｼｰﾄの穴が合うように貼付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "AC束線引き回①",
"WorkItems": [
"1. ①に②を引回す",
"2. ｱｰｽ端子台を⑯⑰にて取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"X015"
]
} | {
"QualityItem": "整線処理",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り処理出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "AC束線引き回①",
"WorkItems": [
"1. ①に②を引回す",
"2. ｱｰｽ端子台を⑯⑰にて取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"X015"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "AC束線引き回②",
"WorkItems": [
"1. ①にAC束線を引回す",
"2. ｱｰｽ端子台を⑯⑰にて取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"X016"
]
} | {
"QualityItem": "整線処理",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り処理出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "AC束線引き回②",
"WorkItems": [
"1. ①にAC束線を引回す",
"2. ｱｰｽ端子台を⑯⑰にて取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"X016"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "AC束線引き回③",
"WorkItems": [
"1. AC束線を㉖にて固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "整線処理",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り処理出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "AC束線引き回④",
"WorkItems": [
"1. AC束線を㉖にて固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "整線処理",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り処理出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DC前束線引き回①",
"WorkItems": [
"1. ②を㉖㉗にて固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"A-1",
"A-2",
"A-3",
"ｲﾝｼｭﾛｯｸ(150mm)"
]
} | {
"QualityItem": "整線処理",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り処理出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DC前束線引き回②",
"WorkItems": [
"1. DC前束線を㉖にて固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"B-1",
"B-2",
"B-3"
]
} | {
"QualityItem": "整線処理",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り処理出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DC前束線引き回③",
"WorkItems": [
"1. DC前束線を㉖にて固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"D-1",
"D-2",
"D-3"
]
} | {
"QualityItem": "整線処理",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り処理出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DC前束線引き回④",
"WorkItems": [
"1. DC前束線を㉖にて固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ(200mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"D-1",
"D-2",
"D-3",
"ｲﾝｼｭﾛｯｸ(150mm)"
]
} | {
"QualityItem": "整線処理",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り処理出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DC後束線引き回①",
"WorkItems": [
"1. ②DC後束線を㉖にて固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"B-1",
"B-2",
"B-3"
]
} | {
"QualityItem": "整線処理",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り処理出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DC後束線引き回②",
"WorkItems": [
"1. DC後束線を㉖にて固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"B-1",
"B-2"
]
} | {
"QualityItem": "整線処理",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り処理出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DC後束線引き回③",
"WorkItems": [
"1. DC後束線を㉖にて固定する",
"2. ⑥を⑯⑰で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"C-1",
"C-2",
"C-3"
]
} | {
"QualityItem": "整線処理",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り処理出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DC後束線引き回③",
"WorkItems": [
"1. DC後束線を㉖にて固定する",
"2. ⑥を⑯⑰で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"C-1",
"C-2",
"C-3"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DC後束線引き回④",
"WorkItems": [
"1. DC後束線を㉖㉗にて固定する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"D-1",
"D-2",
"D-3",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(150mm)"
]
} | {
"QualityItem": "整線処理",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り処理出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾈｸﾀ取付け",
"WorkItems": [
"1. ｺﾈｸﾀをﾌﾞﾗｹｯﾄに取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"P2RXEM4306R",
"P2RXMM4306R",
"P2LXEM4302R",
"P2LXMM4302R"
]
} | {
"QualityItem": "配線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り配線されている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ACｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ取付①",
"WorkItems": [
"■2. ﾄﾞﾗｲﾊﾞｰにｹｰﾌﾞﾙを接続する",
"1. ①に⑥⑦を⑯⑰で取付ける",
"■3. ﾄﾞﾗｲﾊﾞｰにｱｰｽ線(E1K****)を付属のﾎﾞﾙﾄで接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-131",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"XAK4301",
"XAK4306",
"XAK4308",
"XAK4309",
"XAK4307",
"XAK4303",
"XAK4305",
"XAK4304",
"XAK4302",
"E1K4301",
"E1K4306",
"E1K4308",
"E1K4309",
"E1K4307",
"E1K4303",
"E1K4305",
"E1K4304",
"E1K4302",
"検査表①:ｺﾈｸﾀｰ接続確認\tｻｰﾎﾞﾄﾞﾗｲﾊﾞ-(K4301,K4303,K4306-K4309)\t\tｻｰﾎﾞﾄﾞﾗｲﾊﾞ-(K4302,K4304-K4305)",
"検査表①:端子台接続確認 (2)接続箇所,ﾈｼﾞ締付ﾄﾙｸ確認\tｻｰﾎﾞﾄﾞﾗｲﾊﾞ-(K4301,K4303,K4306-K4309)\t\t\t\tｻｰﾎﾞﾄﾞﾗｲﾊﾞ-(K4302,K4304-K4305)",
"締付ﾄﾙｸ 120cN･m",
"接続確認",
"接続確認･ﾈｼﾞ締付ﾄﾙｸ",
"WWYJ-5300-131"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-131",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "№2",
"ToolOther": "120cN･m",
"WorkName": "ACｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ取付①",
"WorkItems": [
"■2. ﾄﾞﾗｲﾊﾞｰにｹｰﾌﾞﾙを接続する",
"1. ①に⑥⑦を⑯⑰で取付ける",
"■3. ﾄﾞﾗｲﾊﾞｰにｱｰｽ線(E1K****)を付属のﾎﾞﾙﾄで接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-131",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"検査表①:ｺﾈｸﾀｰ接続確認\tｻｰﾎﾞﾄﾞﾗｲﾊﾞ-(K4301,K4303,K4306-K4309)\t\tｻｰﾎﾞﾄﾞﾗｲﾊﾞ-(K4302,K4304-K4305)",
"検査表①:端子台接続確認 (2)接続箇所,ﾈｼﾞ締付ﾄﾙｸ確認\tｻｰﾎﾞﾄﾞﾗｲﾊﾞ-(K4301,K4303,K4306-K4309)\t\t\t\tｻｰﾎﾞﾄﾞﾗｲﾊﾞ-(K4302,K4304-K4305)",
"締付ﾄﾙｸ 120cN･m",
"接続確認",
"接続確認･ﾈｼﾞ締付ﾄﾙｸ",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2N・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ACｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ取付②",
"WorkItems": [
"1. ①に⑥を⑯⑰で取付ける",
"■2. ﾄﾞﾗｲﾊﾞｰにｹｰﾌﾞﾙを接続する",
"■3. ﾄﾞﾗｲﾊﾞｰにｱｰｽ線(E1K****)を付属のﾎﾞﾙﾄで接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "WWYJ-5300-131",
"InspectionItems": [
"検査表①:ｺﾈｸﾀｰ接続確認\tｻｰﾎﾞﾄﾞﾗｲﾊﾞ-(K4310,K4403)"
],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"検査表①:端子台接続確認 (2)接続箇所,ﾈｼﾞ締付ﾄﾙｸ確認\tｻｰﾎﾞﾄﾞﾗｲﾊﾞ-(K4310,K4403)",
"E1K4310",
"XAK4310",
"E1K4403",
"XAK4403",
"接続確認",
"接続確認･ﾈｼﾞ締付ﾄﾙｸ",
"WWYJ-5300-131"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-131",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "№2",
"ToolOther": "120cN･m",
"WorkName": "ACｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ取付②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-131",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"E1K4310",
"XAK4310",
"E1K4403",
"XAK4403",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2N・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DC電源(HEPA・ｲｵﾅｲｻﾞｰ用)の取付・配線",
"WorkItems": [
"1. ①に②を⑯⑰で取付ける",
"2. ①に③を⑯⑰で取付ける",
"■3. ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 0.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"ACLaT161",
"ACNaT161",
"検査表①:端子台接続確認 (2)接続箇所,ﾈｼﾞ締付ﾄﾙｸ確認 HEPA･ｲｵﾅｲｻﾞｰ用DC電源追加ﾕﾆｯﾄ DC電源(T161)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "DC電源(HEPA・ｲｵﾅｲｻﾞｰ用)の取付・配線",
"WorkItems": [
"1. ①に②を⑯⑰で取付ける",
"2. ①に③を⑯⑰で取付ける",
"■3. ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 0.8N･m"
],
"InspectionNo": "WWYJ-5300-131",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"ACLaT161",
"ACNaT161",
"検査表①:端子台接続確認 (2)接続箇所,ﾈｼﾞ締付ﾄﾙｸ確認 HEPA･ｲｵﾅｲｻﾞｰ用DC電源追加ﾕﾆｯﾄ DC電源(T161)",
"WWYJ-5300-131"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-131",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "№2",
"ToolOther": "0.8N･m",
"WorkName": "DC電源(HEPA・ｲｵﾅｲｻﾞｰ用)の取付・配線",
"WorkItems": [
"■3. ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 0.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ACLaT161",
"ACNaT161",
"検査表①:端子台接続確認 (2)接続箇所,ﾈｼﾞ締付ﾄﾙｸ確認 HEPA･ｲｵﾅｲｻﾞｰ用DC電源追加ﾕﾆｯﾄ DC電源(T161)",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "0.8N・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾋｰﾀｰBOXの取付・配線",
"WorkItems": [
"1. ①に②を⑯⑰で取付ける",
"2. ①に③を⑯⑰で取付ける",
"■3. ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.8N･m",
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"3aX1601",
"1aX1601",
"2aX1601",
"16X0501",
"検査表①:端子台接続確認 (2)接続箇所,ﾈｼﾞ締付ﾄﾙｸ確認 HEATER BOX(A022)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾋｰﾀｰBOXの取付・配線",
"WorkItems": [
"1. ①に②を⑯⑰で取付ける",
"2. ①に③を⑯⑰で取付ける",
"■3. ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.8N･m",
"締付ﾄﾙｸ 1.6N･m"
],
"InspectionNo": "WWYJ-5300-131",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"3aX1601",
"1aX1601",
"2aX1601",
"16X0501",
"検査表①:端子台接続確認 (2)接続箇所,ﾈｼﾞ締付ﾄﾙｸ確認 HEATER BOX(A022)",
"WWYJ-5300-131"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-131",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "№2",
"ToolOther": "1.6N･m",
"WorkName": "ﾋｰﾀｰBOXの取付・配線",
"WorkItems": [
"■3. ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"3aX1601",
"1aX1601",
"2aX1601",
"検査表①:端子台接続確認 (2)接続箇所,ﾈｼﾞ締付ﾄﾙｸ確認 HEATER BOX(A022)",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.6N・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "№2",
"ToolOther": "1.6N･m",
"WorkName": "ﾋｰﾀｰBOXの取付・配線",
"WorkItems": [
"■3. ｹｰﾌﾞﾙを接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"3aX1601",
"1aX1601",
"2aX1601",
"検査表①:端子台接続確認 (2)接続箇所,ﾈｼﾞ締付ﾄﾙｸ確認 HEATER BOX(A022)",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.8N・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "中継ﾌﾞﾗｹｯﾄ取付(P2COV,P2TB)",
"WorkItems": [
"1. ①に⑥を⑯⑰で取付ける",
"2. ①に⑦を⑯⑰で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"P2COV",
"P2TB"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "中継ﾌﾞﾗｹｯﾄ取付(SDX)",
"WorkItems": [
"1. ①に⑥を⑯⑰で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"SDX"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN及びｺﾈｸﾀﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. ①に⑥を⑯⑰で取付ける",
"2. ①に②を⑱⑲で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.