input stringclasses 1 value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1 value | index stringclasses 1 value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗ/ﾚﾝｽﾞ組立",
"WorkItems": [
"■1. CAMERA の型式を確認し､ｼﾘｱﾙ№を検査表に記入する",
"▲2. LENS-BARREL ねじ部にADHESIVE 接着剤を塗布し､CAMERA に締め込む",
"3. 2の完成品を①にBOLT で取付ける",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"ｶﾒﾗとﾚﾝｽﾞがADHESIVE 接着剤(ｽﾘｰﾎﾞﾝﾄﾞ1401)にて固定されているかを確認",
"㉖接着剤を3ヶ所塗布する",
"･型式確認する･ｼﾘｱﾙ№を記録する",
"出荷仕様に合わせてﾌｫｰｶｽﾘﾝｸﾞの向きを合わせる"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-084",
"InspectionItems": [
"検査表①:安全部品確認"
],
"WorkTypes": [
"■安全作業",
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"接着剤塗布 ｺﾞﾏ粒:3(ねじ部外周)",
"検査表①:ﾚﾝｽﾞﾈｼﾞﾛｯｸ確認",
"検査表①:出荷仕様",
"WWYJ-5300-084"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-084",
"Other": "-",
"ProcessNames": [
"安全工程",
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗ/ﾚﾝｽﾞ組立",
"WorkItems": [
"■1. CAMERA の型式を確認し､ｼﾘｱﾙ№を検査表に記入する",
"▲2. LENS-BARREL ねじ部にADHESIVE 接着剤を塗布し､CAMERA に締め込む",
"3. 2の完成品を①にBOLT で取付ける",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"ｶﾒﾗとﾚﾝｽﾞがADHESIVE 接着剤(ｽﾘｰﾎﾞﾝﾄﾞ1401)にて固定されているかを確認",
"㉖接着剤を3ヶ所塗布する",
"･型式確認する･ｼﾘｱﾙ№を記録する",
"出荷仕様に合わせてﾌｫｰｶｽﾘﾝｸﾞの向きを合わせる"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-084",
"InspectionItems": [
"検査表①:ﾚﾝｽﾞﾈｼﾞﾛｯｸ確認"
],
"WorkTypes": [
"■安全作業",
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"接着剤塗布 ｺﾞﾏ粒:3(ねじ部外周)",
"検査表①:安全部品確認",
"検査表①:出荷仕様",
"WWYJ-5300-084"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-084",
"Other": "-",
"ProcessNames": [
"安全工程",
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗ/ﾚﾝｽﾞ組立",
"WorkItems": [
"■1. CAMERA の型式を確認し､ｼﾘｱﾙ№を検査表に記入する",
"▲2. LENS-BARREL ねじ部にADHESIVE 接着剤を塗布し､CAMERA に締め込む",
"3. 2の完成品を①にBOLT で取付ける",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"ｶﾒﾗとﾚﾝｽﾞがADHESIVE 接着剤(ｽﾘｰﾎﾞﾝﾄﾞ1401)にて固定されているかを確認",
"㉖接着剤を3ヶ所塗布する",
"･型式確認する･ｼﾘｱﾙ№を記録する",
"出荷仕様に合わせてﾌｫｰｶｽﾘﾝｸﾞの向きを合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"接着剤塗布 ｺﾞﾏ粒:3(ねじ部外周)",
"検査表①:安全部品確認",
"検査表①:ﾚﾝｽﾞﾈｼﾞﾛｯｸ確認",
"検査表①:出荷仕様"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "剥がれ無き事ｺﾞﾏ粒:3",
"Method": "目視",
"RecordMethod": "-",
"Other": "接着剤ｽﾘｰﾎﾞﾝﾄﾞ1401",
"ProcessNames": [
"特殊工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗ/ﾚﾝｽﾞ組立",
"WorkItems": [
"■1. CAMERA の型式を確認し､ｼﾘｱﾙ№を検査表に記入する",
"▲2. LENS-BARREL ねじ部にADHESIVE 接着剤を塗布し､CAMERA に締め込む",
"3. 2の完成品を①にBOLT で取付ける",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"ｶﾒﾗとﾚﾝｽﾞがADHESIVE 接着剤(ｽﾘｰﾎﾞﾝﾄﾞ1401)にて固定されているかを確認",
"㉖接着剤を3ヶ所塗布する",
"･型式確認する･ｼﾘｱﾙ№を記録する",
"出荷仕様に合わせてﾌｫｰｶｽﾘﾝｸﾞの向きを合わせる"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-084",
"InspectionItems": [
"検査表①:出荷仕様"
],
"WorkTypes": [
"■安全作業",
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"接着剤塗布 ｺﾞﾏ粒:3(ねじ部外周)",
"検査表①:安全部品確認",
"検査表①:ﾚﾝｽﾞﾈｼﾞﾛｯｸ確認",
"WWYJ-5300-084"
]
} | {
"QualityItem": "ﾈｼﾞﾛｯｸ確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｶﾒﾗとﾚﾝｽﾞが固定されていること",
"Method": "目視",
"RecordMethod": "WWYJ-5300-084",
"Other": "-",
"ProcessNames": [
"特殊工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150",
"ToolOther": "",
"WorkName": "ｶﾒﾗ/ﾚﾝｽﾞ組立",
"WorkItems": [
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"ｶﾒﾗとﾚﾝｽﾞがADHESIVE 接着剤(ｽﾘｰﾎﾞﾝﾄﾞ1401)にて固定されているかを確認",
"出荷仕様に合わせてﾌｫｰｶｽﾘﾝｸﾞの向きを合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業",
"■安全作業"
],
"Words": [
"検査表①:出荷仕様",
"■安全作業",
"▲特殊作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗ/ﾚﾝｽﾞ組立",
"WorkItems": [
"■1. CAMERA の型式を確認し､ｼﾘｱﾙ№を検査表に記入する",
"▲2. LENS-BARREL ねじ部にADHESIVE 接着剤を塗布し､CAMERA に締め込む",
"3. 2の完成品を①にBOLT で取付ける",
"4. 3.完成品にLABEL を貼付ける"
],
"WorkPoints": [
"ｶﾒﾗとﾚﾝｽﾞがADHESIVE 接着剤(ｽﾘｰﾎﾞﾝﾄﾞ1401)にて固定されているかを確認",
"㉖接着剤を3ヶ所塗布する",
"･型式確認する･ｼﾘｱﾙ№を記録する",
"出荷仕様に合わせてﾌｫｰｶｽﾘﾝｸﾞの向きを合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"接着剤塗布 ｺﾞﾏ粒:3(ねじ部外周)",
"検査表①:安全部品確認",
"検査表①:ﾚﾝｽﾞﾈｼﾞﾛｯｸ確認",
"検査表①:出荷仕様",
"WWYJ-5300-084"
]
} | {
"QualityItem": "出荷仕様確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "出荷仕様に合わせて固定",
"Method": "目視",
"RecordMethod": "WWYJ-5300-084",
"Other": "-",
"ProcessNames": [
"特殊工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ(P003)組立",
"WorkItems": [
"1. BRACKET にBLOCK をBOLT WASHER で取付ける",
"2. ①に1の完成品を㉒で組み付け",
"4. 3の完成品にPLATE をBOLT で取付け､BOLT NUT を下図の寸法で組み付け"
],
"WorkPoints": [
"BRACKET の段付き部にｶﾞｲﾄﾞを当てつける事",
"BLOCK は端面から10㎜の位置で固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗﾕﾆｯﾄ組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"1. ①に②をBOLT WASHER で取付ける"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ｶﾒﾗﾕﾆｯﾄ組立②",
"WorkItems": [
"5. ｶﾒﾗ位置を調整する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-084",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"TCP仕様時",
"IC仕様時",
"238.5mm±0.5mm",
"TCP認識:226mm±0.5mmIC認識 :115mm±0.5mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "14㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾕﾆｯﾄ配線",
"WorkItems": [
"2. ①のｶﾒﾗｹｰﾌﾞﾙを結束",
"1. ①にLABEL を貼付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"TCP",
"IC",
"120mm",
"116mm"
]
} | {
"QualityItem": "整線処理",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り処理出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "IC認識照明部組付",
"WorkItems": [
"■1. LED LIGHTING UNIT の型式を確認し､ｼﾘｱﾙNoを検査書に記入する",
"3. SPACER にSCREW を組付け､WASHER を通し①の下図の上側ﾀｯﾌﾟ穴に組付け",
"4. SPACER とWASHER を①の下図の下側取付け穴に㉒で組付け",
"2. BRACKET にLED LIGHTING UNIT をBOLT WASHER で取付け､BRACKET BRACKET をBOLT WASHER で取付ける",
"5. 2の完成品を4の完成品にWASHER ㉒で組付け、ケーブルを結束する"
],
"WorkPoints": [
"本作業は仕様がTCP専用であれば作業不要"
],
"Tolks": [],
"InspectionNo": "WWXJ-5300-058",
"InspectionItems": [
"検査表①:安全部品確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"上から見た図",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WWXJ-5300-058"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWXJ-5300-058",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "IC認識照明部組付",
"WorkItems": [
"■1. LED LIGHTING UNIT の型式を確認し､ｼﾘｱﾙNoを検査書に記入する",
"3. SPACER にSCREW を組付け､WASHER を通し①の下図の上側ﾀｯﾌﾟ穴に組付け",
"4. SPACER とWASHER を①の下図の下側取付け穴に㉒で組付け",
"2. BRACKET にLED LIGHTING UNIT をBOLT WASHER で取付け､BRACKET BRACKET をBOLT WASHER で取付ける",
"5. 2の完成品を4の完成品にWASHER ㉒で組付け、ケーブルを結束する"
],
"WorkPoints": [
"本作業は仕様がTCP専用であれば作業不要"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:安全部品確認",
"上から見た図",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WWXJ-5300-058"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWXJ-5300-058",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾀｸﾞ取付け",
"WorkItems": [
"1. ①にLABEL TERMINAL PROCESS を取付ける"
],
"WorkPoints": [
"合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"E0502R"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ部組立て①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. PLATE にPIN を圧入する",
"2. PLATE にPIN を圧入する",
"1. PLATE にPIN を圧入する",
"2. PLATE にPIN を圧入する",
"M4ﾀｯﾌﾟ",
"本体でｶﾒﾗ位置調整を行うのでﾛｯｸしない"
]
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ部組立て①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. PLATE にPIN を圧入する",
"2. PLATE にPIN を圧入する",
"1. PLATE にPIN を圧入する",
"2. PLATE にPIN を圧入する",
"M4ﾀｯﾌﾟ",
"本体でｶﾒﾗ位置調整を行うのでﾛｯｸしない"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:4.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ部組立て②",
"WorkItems": [],
"WorkPoints": [
"均等に締付ける事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"隙間:0.02mm以内",
"M4ﾀｯﾌﾟ"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:0.02㎜以下",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽ部組立て③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. PLATE にPIN を圧入する",
"出代:3mm"
]
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗ部組立て①",
"WorkItems": [
"■1. CAMERA の型式･ｼﾘｱﾙ確認記入",
"2. PLATE にPIN を圧入する",
"▲3. CAMERA に接着剤を塗布し､LENS-BARREL を取付ける",
"4. 2の完成品を3の完成品にBOLT で取付ける"
],
"WorkPoints": [
"ｶﾒﾗとﾚﾝｽﾞが接着剤(ｽﾘｰﾎﾞﾝﾄﾞ1401)にて固定されているかを確認"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-085",
"InspectionItems": [
"検査表PLATE :安全部品確認"
],
"WorkTypes": [
"■安全作業",
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"Cﾏｳﾝﾄ部",
"※Cﾏｳﾝﾄ部に3ヶ所､120°に塗布する事",
"Cﾏｳﾝﾄ部",
"塗布量目安",
"φ3±1mm",
"出代:4mm",
"検査表PLATE :ﾚﾝｽﾞﾈｼﾞﾛｯｸ確認",
"接着剤塗布 φ3±1mm",
"WWYJ-5300-085"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-085",
"Other": "-",
"ProcessNames": [
"安全工程",
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗ部組立て①",
"WorkItems": [
"■1. CAMERA の型式･ｼﾘｱﾙ確認記入",
"2. PLATE にPIN を圧入する",
"▲3. CAMERA に接着剤を塗布し､LENS-BARREL を取付ける",
"4. 2の完成品を3の完成品にBOLT で取付ける"
],
"WorkPoints": [
"ｶﾒﾗとﾚﾝｽﾞが接着剤(ｽﾘｰﾎﾞﾝﾄﾞ1401)にて固定されているかを確認"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-085",
"InspectionItems": [
"検査表PLATE :ﾚﾝｽﾞﾈｼﾞﾛｯｸ確認"
],
"WorkTypes": [
"■安全作業",
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"Cﾏｳﾝﾄ部",
"※Cﾏｳﾝﾄ部に3ヶ所､120°に塗布する事",
"Cﾏｳﾝﾄ部",
"塗布量目安",
"φ3±1mm",
"検査表PLATE :安全部品確認",
"出代:4mm",
"接着剤塗布 φ3±1mm",
"WWYJ-5300-085"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-085",
"Other": "-",
"ProcessNames": [
"安全工程",
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｶﾒﾗ部組立て①",
"WorkItems": [
"■1. CAMERA の型式･ｼﾘｱﾙ確認記入",
"2. PLATE にPIN を圧入する",
"▲3. CAMERA に接着剤を塗布し､LENS-BARREL を取付ける",
"4. 2の完成品を3の完成品にBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"検査表PLATE :安全部品確認",
"出代:4mm",
"■安全作業",
"▲特殊作業"
]
} | {
"QualityItem": "PIN出代",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:4.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｶﾒﾗ部組立て①",
"WorkItems": [
"■1. CAMERA の型式･ｼﾘｱﾙ確認記入",
"2. PLATE にPIN を圧入する",
"▲3. CAMERA に接着剤を塗布し､LENS-BARREL を取付ける",
"4. 2の完成品を3の完成品にBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"検査表PLATE :安全部品確認",
"出代:4mm",
"■安全作業",
"▲特殊作業"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "接着剤塗布量φ3㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｶﾒﾗ部組立て②",
"WorkItems": [],
"WorkPoints": [
"本体で調整するのでﾅｯﾄはﾛｯｸしない"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"7.5㎜",
"9.0㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗ部ﾍﾞｰｽ取付け",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾈｸﾀﾌﾞﾗｹｯﾄ取付け",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付ける",
"2. 1の完成品にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "IC認識照明部組付け①",
"WorkItems": [
"■1. LED LIGHTING UNIT の型式を確認し､ｼﾘｱﾙNoを検査書に記入する",
"2. LED LIGHTING UNIT にLABEL TERMINAL PROCESS を取付ける",
"3. 2の完成品にBRACKET をBOLT WASHER で取付ける",
"4. 3の完成品にBRACKET BRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"合わせる"
],
"Tolks": [],
"InspectionNo": "WWXJ-5300-058",
"InspectionItems": [
"検査表LED LIGHTING UNIT :安全部品確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"E0502R",
"WWXJ-5300-058"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWXJ-5300-058",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "IC認識照明部組付け①",
"WorkItems": [
"■1. LED LIGHTING UNIT の型式を確認し､ｼﾘｱﾙNoを検査書に記入する",
"2. LED LIGHTING UNIT にLABEL TERMINAL PROCESS を取付ける",
"3. 2の完成品にBRACKET をBOLT WASHER で取付ける",
"4. 3の完成品にBRACKET BRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表LED LIGHTING UNIT :安全部品確認",
"E0502R",
"WWXJ-5300-058"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWXJ-5300-058",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "IC認識照明部組付け②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "IC認識照明部整線",
"WorkItems": [
"1. ①の配線を結束する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"E0502R"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "引き渡し準備",
"WorkItems": [
"1. ①とBOLT を本体工程へ引き渡す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"六角穴付きﾎﾞﾙﾄ M6×20 4本"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ1",
"WorkItems": [
"1. BLOCK FRAME FRAME をNUT NUT BOLT BOLT で取付"
],
"WorkPoints": [
"寸法通り取付けるBLOCK FRAME FRAME の合わせ面に隙間が無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"271㎜",
"119㎜",
"119㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ2",
"WorkItems": [
"1. ①にPLATE をPLATE で挟んでBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ3",
"WorkItems": [
"1. ①を定盤上でN015ﾌﾚｰﾑ上面の高さを測定する"
],
"WorkPoints": [
"0.4㎜以内",
"P002の下面と定盤に隙間が無い事"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-46",
"InspectionItems": [
"検査表①:P(1軸)3 ｱﾙﾑﾌﾚｰﾑ高さ測定"
],
"WorkTypes": [],
"Words": [
"A001",
"P002",
"P004",
"N015",
"P003",
"定盤",
"1~4相互の高低差を確認",
"WWYJ-5300-46"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "寸法:0.4㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-46",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ4",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"230㎜",
"166.3㎜",
"45㎜",
"15㎜",
"28㎜",
"120㎜",
"1. FRAME にBRACKET をNUT BOLT WASHER で取付",
"2. BRACKET にJOINT をBOLT WASHER WASHER で取付",
"3. FRAME にCABLE-SUPPORT を取付",
"4. FRAME の裏からNUT を入れる",
"230㎜",
"166.3㎜",
"45㎜",
"15㎜",
"28㎜",
"120㎜",
"1. FRAME にBRACKET をNUT BOLT WASHER で取付",
"2. BRACKET にJOINT をBOLT WASHER WASHER で取付",
"3. FRAME にCABLE-SUPPORT を取付",
"4. FRAME の裏からNUT を入れる"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付け1",
"WorkItems": [
"1. ①にLABEL を貼付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾒﾓﾘとの合わせ基準",
"ﾒﾓﾘとの合わせ基準"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付け2",
"WorkItems": [
"1. ①にLABEL を貼付け"
],
"WorkPoints": [
"この範囲の貼付け寸法を明示右側も同じ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"2㎜",
"5㎜",
"80㎜",
"5㎜",
"5㎜",
"230㎜",
"5㎜",
"5㎜",
"5㎜",
"2㎜",
"80㎜",
"230㎜"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "銘板貼付け3",
"WorkItems": [
"1. BRACKET にLABEL を貼付け",
"3. COVER にLABEL を貼付け",
"4. COVER にCABLE-SUPPORT を取付ける",
"2. BRACKET にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"23㎜",
"155㎜",
"32㎜",
"2㎜"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾝﾄﾞﾊﾞﾙﾌﾞ1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. JOINT SPACER JOINT を取付",
"8ｾｯﾄ制作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾝﾄﾞﾊﾞﾙﾌﾞ2",
"WorkItems": [
"1. ①にJOINT を取付",
"2. ①にVALVE をBOLT WASHER WASHER で取付",
"1. JOINT VALVE に⑥を取付"
],
"WorkPoints": [
"VALVE は方向あり",
"矢印方向に取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"10㎜"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "治具",
"Size": "",
"ToolOther": "FM-6046",
"WorkName": "搬送PAD組立①",
"WorkItems": [
"1. BLOCK にVACUUM-PAD を仮取付(ﾅｯﾄはVACUUM-PAD の付属品を使用)",
"3. PAD高さ調整を行う｡",
"2. 1.完成品を㉗搬送PAD高さ合わせジグに取付"
],
"WorkPoints": [
"29.8㎜±0.1",
"16ｾｯﾄ製作"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-46",
"InspectionItems": [
"検査表BLOCK :AM1､吸着部高さ確認"
],
"WorkTypes": [],
"Words": [
"VACUUM-PAD の付属品",
"WWYJ-5300-46"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "FM-6046",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "29.8±0.1㎜",
"Method": "治具",
"RecordMethod": "WWYJ-5300-46",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "搬送PAD組立①",
"WorkItems": [
"1. BLOCK にVACUUM-PAD を仮取付(ﾅｯﾄはVACUUM-PAD の付属品を使用)",
"3. PAD高さ調整を行う｡",
"2. 1.完成品を㉗搬送PAD高さ合わせジグに取付"
],
"WorkPoints": [
"29.8㎜±0.1",
"16ｾｯﾄ製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"VACUUM-PAD の付属品",
"検査表BLOCK :AM1､吸着部高さ確認",
"WWYJ-5300-46"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "29.8±0.1㎜",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WWYJ-5300-46",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "搬送PAD組立②",
"WorkItems": [
"▲1. ①に①の付属品をADHESIVE ﾈｼﾞﾛｯｸ材で取付",
"▲2. 1.完成品上部の①付属品のﾌﾟﾗｸﾞを取り外し､JOINT をADHESIVE ﾈｼﾞﾛｯｸ材で取付 ｼﾞｮｲﾝﾄの向き注意"
],
"WorkPoints": [
"吸着穴に接着剤が混入し無い事",
"吸着穴に接着剤が混入し無い事",
"2ｾｯﾄ製作",
"4ｾｯﾄ製作",
"2ｾｯﾄ製作",
"下部ｼﾞｮｲﾝﾄと上部ｼﾞｮｲﾝﾄの向き違いがある3種類製作する"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-46",
"InspectionItems": [
"検査表①:AM2､ねじﾛｯｸ塗布",
"検査表①:AM2､ねじﾛｯｸ塗布"
],
"WorkTypes": [
"▲特殊作業",
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"接着剤塗布 ｺﾞﾏ粒:2",
"接着剤塗布 ｺﾞﾏ粒:2",
"ADHESIVE ねじﾛｯｸ塗布",
"①の付属品(ADHESIVE ねじﾛｯｸ塗布)",
"WWYJ-5300-46"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "WWYJ-5300-46",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "搬送PAD組立③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"▲1. ①に①の付属品をADHESIVE ﾈｼﾞﾛｯｸ材で取付",
"検査表①:AM2､ねじﾛｯｸ塗布",
"吸着穴に接着剤が混入し無い事",
"接着剤塗布 ｺﾞﾏ粒:2",
"8ｾｯﾄ製作",
"①の付属品(ADHESIVE ねじﾛｯｸ塗布)",
"①の付属品(ADHESIVE ねじﾛｯｸ塗布)",
"WWYJ-5300-46"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:2",
"Method": "目視",
"RecordMethod": "WWYJ-5300-46",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "吸着ﾊﾝﾄﾞ組立1",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"210㎜",
"210㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:210.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "吸着ﾊﾝﾄﾞ組立2",
"WorkItems": [
"1. ②を①にNUT BOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"85㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法:85.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "吸着ﾊﾝﾄﾞ組立2",
"WorkItems": [
"1. ②を①にNUT BOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"85㎜"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "吸着ﾊﾝﾄﾞ組立3",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"5㎜",
"110㎜",
"110㎜",
"40㎜",
"40㎜",
"40㎜",
"40㎜",
"55㎜",
"55㎜",
"60㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3.5m",
"ToolOther": "",
"WorkName": "吸着ﾊﾝﾄﾞ組立4",
"WorkItems": [
"1. ①にTUBE TUBE TUBE TUBE TUBE を取付",
"2. 各配管を㉘で固定"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"φ4白 150㎜",
"φ4白 460㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "吸着ﾊﾝﾄﾞ組立5",
"WorkItems": [
"▲1. CAP CAP に㉖を塗布し①に取付"
],
"WorkPoints": [
"CAP の中央部2本の爪は㉘で切断する"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-46",
"InspectionItems": [
"検査表①:2,接着剤塗布"
],
"WorkTypes": [
"▲特殊作業",
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"接着剤塗布 小豆:2",
"WWYJ-5300-46"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布小豆:2",
"Method": "目視",
"RecordMethod": "WWYJ-5300-46",
"Other": "ﾛｯｸﾀｲﾄ415",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "次工程へ引き渡し",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"1. ①②BOLT BOLT WASHER WASHER BOLT WASHER を次工程へ｡"
]
} | {
"QualityItem": "引き渡し部材確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "正しい部材が引き渡される事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立縦①",
"WorkItems": [
"1. FRAME にBRACKET をBOLT ･WASHER ･NUT ･SUPPORT で取付",
"2. FRAME にBRACKET をBOLT ･WASHER ･NUT ･SUPPORT で取付",
"1. FRAME にBRACKET をBOLT ･WASHER ･NUT ･SUPPORT で取付",
"2. FRAME にBRACKET をBOLT ･WASHER ･NUT ･SUPPORT で取付"
],
"WorkPoints": [
"左面",
"上面",
"正面",
"下面",
"正面",
"下面",
"正面",
"下面",
"左面",
"右面",
"左面･右面共",
"左面",
"上面",
"正面",
"下面",
"正面",
"下面",
"正面",
"下面",
"左面",
"右面",
"左面･右面共"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立縦②",
"WorkItems": [
"2. ②にNUT ･SUPPORT ･NUT を取付",
"3. ②にSUPPORT ･NUT を取付",
"1. ①にSUPPORT ･NUT を取付",
"4. ②にCABLE-SUPPORT を取付",
"2. ②にNUT ･SUPPORT ･NUT を取付",
"3. ②にSUPPORT ･NUT を取付",
"1. ①にSUPPORT ･NUT を取付",
"4. ②にCABLE-SUPPORT を取付",
"2. ②にNUT ･SUPPORT ･NUT を取付",
"3. ②にSUPPORT ･NUT を取付",
"1. ①にSUPPORT ･NUT を取付",
"4. ②にCABLE-SUPPORT を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"M6用",
"M4用",
"M6",
"M4用",
"この作業では同じものを2個製作",
"M4",
"M4用",
"この作業では同じものを2個製作",
"M6用",
"M4用",
"M6",
"M4用",
"この作業では同じものを2個製作",
"M4",
"M4用",
"この作業では同じものを2個製作",
"M6用",
"M4用",
"M6",
"M4用",
"この作業では同じものを2個製作",
"M4",
"M4用"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立縦③",
"WorkItems": [
"1. FRAME にSUPPORT ･NUT 挿入しBRACKET をBOLT ･WASHER で取付"
],
"WorkPoints": [
"上面",
"左面",
"正面",
"下面",
"上面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立横①",
"WorkItems": [
"1. FRAME にBRACKET をBOLT ･WASHER ･NUT ･SUPPORT で取付",
"2. FRAME にBRACKET をBOLT ･WASHER ･NUT ･SUPPORT で取付",
"1. FRAME にBRACKET をBOLT ･WASHER ･NUT ･SUPPORT で取付",
"2. FRAME にBRACKET をBOLT ･WASHER ･NUT ･SUPPORT で取付"
],
"WorkPoints": [
"左面",
"上面",
"正面",
"下面",
"正面",
"下面",
"正面",
"下面",
"左面",
"上面",
"正面",
"下面",
"正面",
"下面",
"正面",
"下面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"41mm",
"41mm",
"560mm",
"1400mm",
"41mm",
"41mm",
"560mm",
"1400mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立横②",
"WorkItems": [
"1. ①にNUT ･SUPPORT ･NUT ･NUT を取付",
"2. ①にNUT ･SUPPORT ･NUT ･NUT を取付",
"3. ②にNUT ･SUPPORT ･NUT を取付",
"1. ①にNUT ･SUPPORT ･NUT ･NUT を取付",
"2. ①にNUT ･SUPPORT ･NUT ･NUT を取付",
"3. ②にNUT ･SUPPORT ･NUT を取付",
"1. ①にNUT ･SUPPORT ･NUT ･NUT を取付",
"2. ①にNUT ･SUPPORT ･NUT ･NUT を取付",
"3. ②にNUT ･SUPPORT ･NUT を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"×4",
"×4",
"×2",
"×2",
"×4",
"×4",
"×2",
"×2",
"×4",
"×4",
"×2",
"×2"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3.5m",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立UPPER",
"WorkItems": [
"1. ①･②･③･④をBOLT ･WASHER で取付",
"2. 1.完成品にCABLE-SUPPORT を取付"
],
"WorkPoints": [
"左側",
"上面で組立する事",
"上面",
"裏面",
"左側",
"裏面に取付する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示の寸法である事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "HEPA大組立",
"WorkItems": [
"1. BLOWER の取付ﾌﾞﾗｹｯﾄをBRACKET と交換する"
],
"WorkPoints": [
"4ヶ所",
"交換したﾌﾞﾗｹｯﾄは廃棄",
"交換前と反対で下面を合わせて固定する",
"BRACKET の曲げが下側",
"下面を合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "HEPA小組立",
"WorkItems": [
"1. BLOWER の取付ﾌﾞﾗｹｯﾄをBRACKET と交換する"
],
"WorkPoints": [
"4ヶ所",
"交換したﾌﾞﾗｹｯﾄは廃棄",
"交換前と反対で下面を合わせて固定する",
"BRACKET の曲げが下側",
"下面を合わせる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上側ｶﾊﾞｰ準備①",
"WorkItems": [
"1. GROMMET に切り込みを入れる",
"2. COVER ･COVER ･COVER ･COVER に1.完成品を取付"
],
"WorkPoints": [
"切り込み"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを4個製作",
"1.完成品",
"1.完成品",
"1.完成品",
"1.完成品"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "上側ｶﾊﾞｰ準備②",
"WorkItems": [
"1. COVER にGROMMET を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾒﾝﾃﾅﾝｽﾗｲﾄAM組立",
"WorkItems": [
"1. BRACKET にLED-LAMP-UNIT をBOLT WASHER WASHER で取付ける",
"2. 1の完成品にLABEL TERMINAL PROCESS を取付ける",
"3. 2の完成品とNUT SUPPORT BOLT WASHER を付属する"
],
"WorkPoints": [
"合わせる",
"ﾗﾍﾞﾙ2種類"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"E0031R",
"E0031R",
"E0033R",
"SFN-AS4 4個",
"SFA-9A2 4個",
"六角穴付きﾎﾞﾙﾄM4×10 4本平座金 みがき丸 4 4個",
"この作業ではﾗﾍﾞﾙ違いを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾝｸﾞI/O負荷ﾎﾞｰﾄﾞ設定",
"WorkItems": [
"★2. RING I/O LOAD BOARD ﾎﾞｰﾄﾞの設定を行う",
"■★1. RING I/O LOAD BOARD の型式確認後､ｼﾘｱﾙ番号を検査表に記入する"
],
"WorkPoints": [
"この部分の番号を記入する",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-132",
"InspectionItems": [],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"■安全作業",
"★静電対策作業",
"この部分の型式を確認する",
"検査表RING I/O LOAD BOARD :2.基板･ﾕﾆｯﾄ設定確認",
"SW1",
"部品番号",
"K300A",
"SW2",
"0FF:1-8ON:なし",
"検査表RING I/O LOAD BOARD :1.型式･ｼﾘｱﾙ･検査書ﾁｪｯｸ 1",
"SW1",
"SW2",
"WWYJ-5300-132"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-132",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾝｸﾞI/O負荷ﾎﾞｰﾄﾞ設定",
"WorkItems": [
"★2. RING I/O LOAD BOARD ﾎﾞｰﾄﾞの設定を行う",
"■★1. RING I/O LOAD BOARD の型式確認後､ｼﾘｱﾙ番号を検査表に記入する"
],
"WorkPoints": [
"この部分の番号を記入する",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-132",
"InspectionItems": [
"検査表RING I/O LOAD BOARD :1.型式･ｼﾘｱﾙ･検査書ﾁｪｯｸ 1"
],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"■安全作業",
"★静電対策作業",
"この部分の型式を確認する",
"検査表RING I/O LOAD BOARD :2.基板･ﾕﾆｯﾄ設定確認",
"SW1",
"部品番号",
"K300A",
"SW2",
"0FF:1-8ON:なし",
"SW1",
"SW2",
"WWYJ-5300-132"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-132",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾝｸﾞI/O負荷ﾎﾞｰﾄﾞ設定",
"WorkItems": [
"★2. RING I/O LOAD BOARD ﾎﾞｰﾄﾞの設定を行う",
"■★1. RING I/O LOAD BOARD の型式確認後､ｼﾘｱﾙ番号を検査表に記入する"
],
"WorkPoints": [
"この部分の番号を記入する",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"■安全作業",
"★静電対策作業",
"この部分の型式を確認する",
"検査表RING I/O LOAD BOARD :2.基板･ﾕﾆｯﾄ設定確認",
"SW1",
"部品番号",
"K300A",
"SW2",
"0FF:1-8ON:なし",
"検査表RING I/O LOAD BOARD :1.型式･ｼﾘｱﾙ･検査書ﾁｪｯｸ 1",
"SW1",
"SW2",
"WWYJ-5300-132"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定されている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-132",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "P2TB中継ﾌﾞﾗｹｯﾄ組立(正流れ)",
"WorkItems": [
"★1. BRACKET に③をBOLT WASHER で取付け､CABLE-SUPPORT を挿し込む",
"2. SOCKET にRELAY LAMP を装着後BRACKET にSOCKET をBOLT WASHER WASHER で取付ける",
"3. BRACKET にCIRCUIT-PROTECTOR CIRCUIT-PROTECTOR をWASHER BOLT で取付ける",
"4. BRACKET にCABLE をBOLT WASHER ㉒で取付ける"
],
"WorkPoints": [
"09A068 ｹｰﾌﾞﾙに同梱のD1500を外して取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"P2TB1P",
"P2TB2P"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "P2COV中継ﾌﾞﾗｹｯﾄ組立(正流れ)",
"WorkItems": [
"1. BRACKET にCABLE-SUPPORT を挿し込む",
"2. 1.完成品にRELAY をBOLT WASHER WASHER で取付ける",
"3. RELAY にTERMINAL を仮付けする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "P2TB中継ﾌﾞﾗｹｯﾄ組立(逆流れ)",
"WorkItems": [
"★1. BRACKET に③をBOLT WASHER で取付け､CABLE-SUPPORT を挿し込む",
"2. SOCKET にRELAY LAMP を装着後BRACKET にSOCKET をBOLT WASHER WASHER で取付ける",
"3. BRACKET にCIRCUIT-PROTECTOR CIRCUIT-PROTECTOR をWASHER BOLT で取付ける",
"4. BRACKET にCABLE をBOLT WASHER ㉒で取付ける"
],
"WorkPoints": [
"09A068 ｹｰﾌﾞﾙに同梱のD1500を外して取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"★静電対策作業",
"■安全作業"
],
"Words": [
"P2TB1P",
"P2TB2P"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "P2COV中継ﾌﾞﾗｹｯﾄ組立(逆流れ)",
"WorkItems": [
"1. BRACKET にCABLE-SUPPORT を挿し込む",
"2. 1.完成品にRELAY をBOLT WASHER WASHER で取付ける",
"3. RELAY にTERMINAL を仮付けする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾗｲﾊﾞｰLANｹｰﾌﾞﾙﾀｸﾞ取付(正流れ)",
"WorkItems": [
"1. CABLE CABLE CABLE にMARK TUBE TERMINAL PROCESS を結束する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"X2AK4206",
"X2BK4208",
"A側",
"B側"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾗｲﾊﾞｰLANｹｰﾌﾞﾙﾀｸﾞ取付(逆流れ)",
"WorkItems": [
"1. CABLE CABLE CABLE にMARK TUBE TERMINAL PROCESS を結束する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"X2AK4206",
"X2BK4208",
"A側",
"B側"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "回生抵抗ﾀｸﾞ取付",
"WorkItems": [
"■1. RESISTOR TERMINAL PROCESS の型式を確認し検査書にﾁｪｯｸする",
"2. RESISTOR TERMINAL PROCESS にMARK TUBE TERMINAL PROCESS を取付ける"
],
"WorkPoints": [
"余長をまとめ結束､ULﾁｭｰﾌﾞにﾀｸﾞを取付けること",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-132",
"InspectionItems": [
"検査表RESISTOR TERMINAL PROCESS :型式･ｼﾘｱﾙ･検査書ﾁｪｯｸ1"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WWYJ-5300-132"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-132",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "回生抵抗取付(正流れ)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"1. PLATE PLATE にSPACER をBOLT WASHER にて取付る",
"2. PLATE PLATE に⑤をSPACER BOLT WASHER BOLT にて取付ける",
"SP2XRM4301P",
"P2RXRM4306P",
"P2HRM4310P",
"P2LXRM4302P",
"P2LYRM4303P",
"P2RYRM4307P",
"SDXRM4403P"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "回生抵抗取付(逆流れ)",
"WorkItems": [
"1. PLATE PLATE にSPACER をBOLT WASHER にて取付る",
"2. PLATE PLATE に⑤をSPACER BOLT WASHER BOLT にて取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"SP2XRM4301P",
"P2RXRM4306P",
"P2HRM4310P",
"P2LXRM4302P",
"P2LYRM4303P",
"P2RYRM4307P",
"SDXRM4403P"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ設定",
"WorkItems": [
"2. ACｻｰﾎﾞﾓｰﾀﾄﾞﾗｲﾊﾞの設定",
"■1. MOTOR-DRIVER MOTOR-DRIVER MOTOR-DRIVER MOTOR-DRIVER MOTOR-DRIVER の型式確認後､ｼﾘｱﾙ番号を検査表に記入する"
],
"WorkPoints": [
"この部分の型式を確認する",
"この部分の番号を記入する",
"ﾏｽｷﾝｸﾞﾃｰﾌﾟに部品番号･軸名を記入し貼付ける",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-132",
"InspectionItems": [
"検査表MOTOR-DRIVER :型式･ｼﾘｱﾙ･検査書ﾁｪｯｸ1"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"MSD",
"■安全作業",
"LSD",
"表に基きﾄﾞﾗｲﾊﾞｰを設定する",
"検査表MOTOR-DRIVER :2.基板･ﾕﾆｯﾄ設定確認",
"WWYJ-5300-132"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-132",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ設定",
"WorkItems": [
"2. ACｻｰﾎﾞﾓｰﾀﾄﾞﾗｲﾊﾞの設定",
"■1. MOTOR-DRIVER MOTOR-DRIVER MOTOR-DRIVER MOTOR-DRIVER MOTOR-DRIVER の型式確認後､ｼﾘｱﾙ番号を検査表に記入する"
],
"WorkPoints": [
"この部分の型式を確認する",
"この部分の番号を記入する",
"ﾏｽｷﾝｸﾞﾃｰﾌﾟに部品番号･軸名を記入し貼付ける",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-132",
"InspectionItems": [
"検査表MOTOR-DRIVER :2.基板･ﾕﾆｯﾄ設定確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"MSD",
"■安全作業",
"LSD",
"表に基きﾄﾞﾗｲﾊﾞｰを設定する",
"検査表MOTOR-DRIVER :型式･ｼﾘｱﾙ･検査書ﾁｪｯｸ1",
"WWYJ-5300-132"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-132",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ設定",
"WorkItems": [
"2. ACｻｰﾎﾞﾓｰﾀﾄﾞﾗｲﾊﾞの設定",
"■1. MOTOR-DRIVER MOTOR-DRIVER MOTOR-DRIVER MOTOR-DRIVER MOTOR-DRIVER の型式確認後､ｼﾘｱﾙ番号を検査表に記入する"
],
"WorkPoints": [
"この部分の型式を確認する",
"この部分の番号を記入する",
"ﾏｽｷﾝｸﾞﾃｰﾌﾟに部品番号･軸名を記入し貼付ける",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"MSD",
"■安全作業",
"LSD",
"表に基きﾄﾞﾗｲﾊﾞｰを設定する",
"検査表MOTOR-DRIVER :型式･ｼﾘｱﾙ･検査書ﾁｪｯｸ1",
"検査表MOTOR-DRIVER :2.基板･ﾕﾆｯﾄ設定確認",
"WWYJ-5300-132"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定されている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-132",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立①(正流れ)",
"WorkItems": [
"1. BRACKET に②をBOLT WASHER にて取付ける",
"2. 1.完成品に⑤をBOLT WASHER にて取付ける",
"3. 2.完成品の各ﾄﾞﾗｲﾊﾞｰにCLIP をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"K4301SP2軸",
"K4302P2LX軸",
"K4304P2LZ軸",
"K4305P2LV軸",
"K4303P2LY軸",
"K4307P2LY軸"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立②(正流れ)",
"WorkItems": [
"1. BRACKET に②をBOLT WASHER にて取付ける",
"2. 2.完成品の各ﾄﾞﾗｲﾊﾞｰにCLIP をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"K4309P2RV軸",
"K4308P2RZ軸",
"K4306P2RX軸"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立③(正流れ)",
"WorkItems": [
"1. BRACKET に②⑧をBOLT WASHER にて取付ける",
"2. 1.完成品に⑤をBOLT WASHER にて取付ける",
"3. 2.完成品のﾄﾞﾗｲﾊﾞｰにCLIP をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"K4310P2H軸",
"K4403SDX軸"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立④(逆流れ)",
"WorkItems": [
"1. BRACKET に②をBOLT WASHER にて取付ける",
"2. 1.完成品に⑤をBOLT WASHER にて取付ける",
"3. 2.完成品の各ﾄﾞﾗｲﾊﾞｰにCLIP をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"K4301SP2軸",
"K4303P2LY軸",
"K4307P2LY軸",
"K4309P3RV軸",
"K4308P2RZ軸",
"K4306P2RX軸"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立⑤(逆流れ)",
"WorkItems": [
"1. BRACKET に②をBOLT WASHER にて取付ける",
"2. 1.完成品の各ﾄﾞﾗｲﾊﾞｰにCLIP をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"K4302P2LX軸",
"K4304P2LZ軸",
"K4305P2LV軸"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｰﾎﾞﾄﾞﾗｲﾊﾞｰ組立⑥(逆流れ)",
"WorkItems": [
"1. BRACKET に②をBOLT WASHER にて取付ける",
"2. 1.完成品に⑤をBOLT WASHER にて取付ける",
"3. 2.完成品のﾄﾞﾗｲﾊﾞｰにCLIP をBOLT で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"K4310P2H軸",
"K4403SDX軸"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN組立①(架台内、組立①)",
"WorkItems": [
"1. BRACKET へFAN FAN-GUARD をSCREW WASHER NUT で取付"
],
"WorkPoints": [
"FANｹｰﾌﾞﾙの出代を同一方向へ",
"2set作成する",
"FANｹｰﾌﾞﾙの出る方向と吹き出し方向を図参照にして取付ける事｡",
"FANｹｰﾌﾞﾙ固定",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"FANｹｰﾌﾞﾙ",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"FANﾌﾚｰﾑに固定"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN組立②(架台内、組立②)",
"WorkItems": [
"1. BRACKET へFAN FAN-GUARD をSCREW WASHER NUT で取付"
],
"WorkPoints": [
"FANｹｰﾌﾞﾙの出る方向と吹き出し方向を図参照にして取付ける事｡",
"4個作成する",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"FANｹｰﾌﾞﾙ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN組立③(架台内、ﾀｸﾞ取付け)",
"WorkItems": [
"1. ①②にMARK TUBE TERMINAL PROCESS ﾀｸﾞを結束する"
],
"WorkPoints": [
"合わせる",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"2ｾｯﾄ",
"2ｾｯﾄ",
"G10B42R",
"G10B44R",
"G10B45R",
"G10B43R"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN組立④(架台上面、組立て)",
"WorkItems": [
"1. BRACKET にFAN FAN-GUARD をSCREW WASHER NUT で取付ける",
"3. 2の完成品にSPACER をBOLT WASHER で取付ける",
"2. 1の完成品にBRACKET をBOLT WASHER で取付ける",
"4. FANｹｰﾌﾞﾙをｲﾝｼｭﾛｯｸで結束する"
],
"WorkPoints": [
"FANの排気方向に注意",
"5ｾｯﾄ組立",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する",
"5ｾｯﾄ中3ｾｯﾄに取付ける",
"BRACKETの取付方向に注意"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN組立⑤(架台上面、ﾀｸﾞ取付け)",
"WorkItems": [
"1. ①のFANｹｰﾌﾞﾙにMARK TUBE TERMINAL PROCESS を結束する"
],
"WorkPoints": [
"合わせる",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"G10B30R",
"G10B32R",
"G10B34R",
"G10B31R",
"SPACER有",
"SPACER無",
"G10B33R",
"G10B40R",
"G10B41R"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "光ﾌｧｲﾊﾞｰｹｰﾌﾞﾙﾀｸﾞ取付",
"WorkItems": [
"1. OPTICAL-FIBER OPTICAL-FIBER OPTICAL-FIBER にMARK TUBE TERMINAL PROCESS を結束する"
],
"WorkPoints": [
"ｺﾈｸﾀを左にして文字が読めるように結束する",
"表のﾀｸﾞ名称を参照しﾀｸﾞを結束する",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"CN4K300A"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "銘板貼付1(ｽｲｯﾁﾊﾟﾈﾙ)",
"WorkItems": [
"1. COVER にLABEL LABEL LABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"MA1",
"図を参考にﾏｸﾞﾈｯﾄｼｰﾄを取付し銘板を貼付"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付2(ｽｲｯﾁﾊﾟﾈﾙ)",
"WorkItems": [
"■2. ①にLABEL を貼付ける",
"■1. LABEL の型式確認をする"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"型式:PW0108M1"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-017",
"InspectionItems": [
"検査表①:安全部品確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:貼付位置確認",
"WWYJ-5300-017"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付2(ｽｲｯﾁﾊﾟﾈﾙ)",
"WorkItems": [
"■2. ①にLABEL を貼付ける",
"■1. LABEL の型式確認をする"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"型式:PW0108M1"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-017",
"InspectionItems": [
"検査表①:貼付位置確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:安全部品確認",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付3(右ﾌﾛﾝﾄｶﾊﾞｰ)",
"WorkItems": [
"1. COVER にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "銘板貼付4(左ﾌﾛﾝﾄｶﾊﾞｰ)",
"WorkItems": [
"1. COVER にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"LABEL 穴のｾﾝﾀｰへ貼付ける"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付5(左ﾌﾛﾝﾄｶﾊﾞｰ)",
"WorkItems": [
"■2. ①にLABEL LABEL を貼付ける",
"■1. LABEL LABEL の型式確認をする"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"型式:LABEL PW0102M1､LABEL PC013901"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-017",
"InspectionItems": [
"検査表①:安全部品確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:貼付位置確認",
"WWYJ-5300-017"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "銘板貼付5(左ﾌﾛﾝﾄｶﾊﾞｰ)",
"WorkItems": [
"■2. ①にLABEL LABEL を貼付ける",
"■1. LABEL LABEL の型式確認をする"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"型式:LABEL PW0102M1､LABEL PC013901"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-017",
"InspectionItems": [
"検査表①:貼付位置確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:安全部品確認",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付6(前面下ｶﾊﾞｰ)",
"WorkItems": [
"■2. COVER にLABEL を貼付ける",
"■1. LABEL の型式確認をする"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"型式:PC010201",
"2ｾｯﾄ貼付け"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-017",
"InspectionItems": [
"検査表LABEL :安全部品確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表LABEL :貼付位置確認",
"KT4",
"図を参考にﾏｸﾞﾈｯﾄｼｰﾄを取付し銘板を貼付",
"WWYJ-5300-017"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付6(前面下ｶﾊﾞｰ)",
"WorkItems": [
"■2. COVER にLABEL を貼付ける",
"■1. LABEL の型式確認をする"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"型式:PC010201",
"2ｾｯﾄ貼付け"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-017",
"InspectionItems": [
"検査表LABEL :貼付位置確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表LABEL :安全部品確認",
"KT4",
"図を参考にﾏｸﾞﾈｯﾄｼｰﾄを取付し銘板を貼付",
"■安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付7(前面下ｶﾊﾞｰ左)",
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"貼付前に脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付8(後面ｶﾊﾞｰ)",
"WorkItems": [
"3. 2.完成品にｼﾘｱﾙNo.ﾗﾍﾞﾙを貼付ける",
"■2. COVER にLABEL を貼付ける",
"■1. LABEL の型式確認をする"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"型式:PD0101M1",
"ｼﾘｱﾙNo.ﾗﾍﾞﾙは､生産管理にて作成",
"ｼﾘｱﾙNo."
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-017",
"InspectionItems": [
"検査表LABEL :安全部品確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表LABEL :貼付位置確認",
"WWYJ-5300-017"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "銘板貼付8(後面ｶﾊﾞｰ)",
"WorkItems": [
"3. 2.完成品にｼﾘｱﾙNo.ﾗﾍﾞﾙを貼付ける",
"■2. COVER にLABEL を貼付ける",
"■1. LABEL の型式確認をする",
"3. 2.完成品にｼﾘｱﾙNo.ﾗﾍﾞﾙを貼付ける",
"■2. COVER にLABEL を貼付ける",
"■1. LABEL の型式確認をする"
],
"WorkPoints": [
"貼付前に脱脂する事",
"貼付前に脱脂する事"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-017",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表LABEL :安全部品確認",
"■安全作業",
"検査表LABEL :安全部品確認"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±2㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "銘板貼付9(後面下ｶﾊﾞｰ)",
"WorkItems": [
"■2. COVER COVER にLABEL を貼付ける",
"■1. LABEL の型式確認をする"
],
"WorkPoints": [
"貼付前に脱脂する事",
"±2㎜以下",
"型式:PC010201"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-017",
"InspectionItems": [
"検査表LABEL :安全部品確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表LABEL :貼付位置確認",
"KT4",
"図を参考にﾏｸﾞﾈｯﾄｼｰﾄを取付し銘板を貼付",
"WWYJ-5300-017"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-017",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.