input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "θ1側基板結束3FAN線接続・結束",
"WorkItems": [
"1. ﾒｲﾝﾎﾞｰﾄﾞ(K301)のCN27を接続",
"2. 略図の順序で結束"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "GWETJ-F013-002",
"InspectionItems": [
"検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"【結束手順 1】ﾌﾞﾗｹｯﾄにFAN線のみを結束【注意】FAN線は干渉防止であまりたるませない",
"【結束手順 2】ﾌﾞﾗｹｯﾄにFAN線と中継線を結束",
"【結束手順 3】FAN線を折り返しﾌﾞﾗｹｯﾄに中継線と結束",
"【注意】FAN線は干渉防止であまりたるませない",
"CN27",
"GWETJ-F013-002"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "GWETJ-F013-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾆｱﾓｰﾀｰ信号線接続・結束",
"WorkItems": [
"1. ﾒｲﾝﾎﾞｰﾄﾞ(K301)のCN8を接続",
"2. 略図の順序で結束"
],
"WorkPoints": [
"【注意】 配線の曲げ部分がﾌﾞﾗｹｯﾄに干渉してい無い事"
],
"Tolks": [],
"InspectionNo": "GWETJ-F013-002",
"InspectionItems": [
"検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"【結束手順 2】ﾌﾞﾗｹｯﾄに結束",
"【結束手順 1】ﾌﾞﾗｹｯﾄに結束曲げ部分が窮屈にならない様にする",
"CN8",
"【結束手順 3】ﾀｲﾏｳﾝﾄに結束",
"【注意】曲げ部分にﾌﾞﾗｹｯﾄとの過度な干渉が無い事",
"GWETJ-F013-002"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "GWETJ-F013-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ線引き回し",
"WorkItems": [
"1. ﾄﾞﾛｱｺﾈｸﾀｰ線を引き廻す ※青矢印部分"
],
"WorkPoints": [
"一部を省いて描いています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"白ｺﾈｸﾀｰ線､黒ｺﾈｸﾀｰ線､FG線を分岐させる"
]
} | {
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り経路で配線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ接続",
"WorkItems": [
"1. ｺﾈｸﾀｰを接続する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "GWETJ-F013-002",
"InspectionItems": [
"検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"CN4",
"CN6",
"GWETJ-F013-002"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "GWETJ-F013-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN線接続",
"WorkItems": [
"1. FAN線を接続"
],
"WorkPoints": [
"略図の様に折り返した後に接続する"
],
"Tolks": [],
"InspectionNo": "GWETJ-F013-002",
"InspectionItems": [
"検査表①:ﾒｲﾝﾎﾞｰﾄﾞ(K301)接続確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"FAN線/CN28",
"GWETJ-F013-002"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "GWETJ-F013-002",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ線結束",
"WorkItems": [
"1. ﾄﾞﾛｱｺﾈｸﾀｰ線結束"
],
"WorkPoints": [
"【注意】 ﾄﾞﾛｱｹｰﾌﾞﾙが金属ｴｯｼﾞ部分と干渉のない様にする"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"【結束手順 1】ﾀｲﾏｳﾝﾄに配線を結束",
"【結束手順 4】ﾌﾞﾗｹｯﾄに配線を結束",
"【結束手順 2】ﾀｲﾏｳﾝﾄに配線を結束",
"【結束手順 5】ﾄﾞﾛｱｺﾈｸﾀｰ白ﾁｭｰﾌﾞに配線を結束",
"【結束手順 3】ﾓｰﾀｰﾎﾞﾃﾞｨに配線を結束"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ配線・FAN線結束",
"WorkItems": [
"1. ﾄﾞﾛｱｺﾈｸﾀｰ･FAN 線結束"
],
"WorkPoints": [
"【注意】 結束後､ｴｯｼﾞ部分や基板と配線の干渉が無い事",
"【注意】 ｴｯｼﾞ部分と配線の干渉が無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"【結束手順 1】ﾌﾞﾗｹｯﾄにﾄﾞﾛｱｺﾈｸﾀｰ線とFAN線を結束※折り返したFAN線は結束しない",
"【結束手順 2】FAN線を折り返し､ﾄﾞﾛｱｺﾈｸﾀｰ線とﾌﾞﾗｹｯﾄに結束",
"【11",
"【結束手順 3】ﾌﾞﾗｹｯﾄに結束"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "80cN･m",
"WorkName": "ﾄﾞﾛｱｺﾈｸﾀｰ接続",
"WorkItems": [
"■1. FG線をSCREW にて締結"
],
"WorkPoints": [
"一部を省いて描いています"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "GWETJ-F013-002",
"InspectionItems": [
"検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｶﾊﾞｰ銘板貼付け",
"WorkItems": [
"1. COVER のﾗﾍﾞﾙ貼付面の油分を除去",
"2. COVER にLABEL LABEL LABEL を貼付け"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"30mm",
"45mm"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "60cN･m",
"WorkName": "ｶﾊﾞｰ取付",
"WorkItems": [
"■1. ①に②をSCREW にて取付"
],
"WorkPoints": [
"計8か所を仮固定後､締結する"
],
"Tolks": [
"締付ﾄﾙｸ 60cN･m"
],
"InspectionNo": "GWETJ-F013-002",
"InspectionItems": [
"検査表①:ﾈｼﾞ締め付けﾄﾙｸ確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "付属品ﾊﾟｯｷﾝｸﾞ",
"WorkItems": [
"1. SPRING SPRING(BLACK) CLAMP-ARM(BLACK) FILTER TUBE (70MM CUT) をﾊﾟｯｷﾝｸﾞして､付属品とする"
],
"WorkPoints": [
"付属品はﾊﾟｯｷﾝｸﾞして､ﾍｯﾄﾞ完成品と合わせて払い出す"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"付属品",
"合わせて払い出す"
]
} | {
"QualityItem": "付属品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した付属品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾑﾌｫﾛｱ部組立",
"WorkItems": [
"1. BRACKET の取付面(青色部)に砥石を掛ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.5㎜(BOX)",
"ToolOther": "150cN･m",
"WorkName": "ｶﾑﾌｫﾛｱ部組立",
"WorkItems": [
"2. 1完成品にCAM-FOLLOWER をWASHER WASHER NUT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙﾐ用砥石",
"Size": "",
"ToolOther": "ｽｰﾊﾟｰｼｬｲﾅｰ砥石",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備",
"WorkItems": [
"1. PLATE の両面に㉖を掛ける"
],
"WorkPoints": [
"表面(座ｸﾞﾘ有)は特に表面に傷がつかない様に注意する事",
"PLATE に打痕やﾊﾞﾘが無い事",
"緑色部の9箇所を測定する事(平面度:0.1㎜以内)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"表 面"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備",
"WorkItems": [
"1. PLATE の両面に㉖を掛ける"
],
"WorkPoints": [
"表面(座ｸﾞﾘ有)は特に表面に傷がつかない様に注意する事",
"PLATE に打痕やﾊﾞﾘが無い事",
"緑色部の9箇所を測定する事(平面度:0.1㎜以内)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"表 面"
]
} | {
"QualityItem": "平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.1㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①",
"WorkItems": [
"2. ①にBRACKET WASHER をBOLT で取付ける",
"1. BRACKET に㉖油砥石を掛ける"
],
"WorkPoints": [
"BRACKET の全面にﾊﾞﾘ､打痕等ないか確認する事",
"青色部に㉖を掛ける"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①",
"WorkItems": [
"2. ①にBRACKET WASHER をBOLT で取付ける",
"1. BRACKET に㉖油砥石を掛ける"
],
"WorkPoints": [
"BRACKET の全面にﾊﾞﾘ､打痕等ないか確認する事",
"青色部に㉖を掛ける"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-②",
"WorkItems": [
"1. ①に②をBOLT で取付ける"
],
"WorkPoints": [
"②を㉖の青点線部に押し当てて取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-②",
"WorkItems": [
"1. ①に②をBOLT で取付ける"
],
"WorkPoints": [
"②を㉖の青点線部に押し当てて取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"青色部に㉖を掛ける（面取りが無い側）",
"BLOCK の面取り位置を図左手前にして取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "打痕、ﾊﾞﾘ無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"青色部に㉖を掛ける（面取りが無い側）",
"BLOCK の面取り位置を図左手前にして取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"青色部に㉖を掛ける（面取りが無い側）",
"BLOCK の面取り位置を図左手前にして取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-④",
"WorkItems": [
"1. ①にGUIDE をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"GUIDE は各々外側(矢印方向)に寄せて取付ける事(傾き無き事)"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "交換台車支持部(右)1",
"WorkItems": [
"1. GUIDE にPIN を圧入する"
],
"WorkPoints": [
"PIN出代:4mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "PIN出代:4㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "13㎜BOX",
"ToolOther": "12.7N･m",
"WorkName": "交換台車支持部(右)1",
"WorkItems": [
"2. 1完成品にSTOPPER を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 12.7N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "12.7N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "26.5N･m",
"WorkName": "交換台車支持部(右)2",
"WorkItems": [
"1. ①にCAM-FOLLOWER を取付ける"
],
"WorkPoints": [
"付属ﾅｯﾄ",
"当付け方向"
],
"Tolks": [
"締付ﾄﾙｸ 26.5N･m",
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "26.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.5N･m",
"WorkName": "交換台車支持部(右)2",
"WorkItems": [
"1. ①にCAM-FOLLOWER を取付ける"
],
"WorkPoints": [
"付属ﾅｯﾄ",
"当付け方向"
],
"Tolks": [
"締付ﾄﾙｸ 26.5N･m",
"締付ﾄﾙｸ 3.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20N･m",
"WorkName": "交換台車支持部(右)3",
"WorkItems": [
"1. FRAME(R) に①BLOCK をBOLT で取付ける"
],
"WorkPoints": [
"当付け方向",
"当付け方向",
"17/34連+17/34連仕様の取付け位置",
"17/34連 + ﾄﾚｲ仕様の取付け位置"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "交換台車支持部(右)4",
"WorkItems": [
"1. ①に②を③⑯⑰⑱で取付ける",
"2. 1完成品を④に⑲⑳㉑㉒で取付ける"
],
"WorkPoints": [
"面位置",
"矢印方向に押し当てて取付ける",
"長穴ｾﾝﾀｰに合せる",
"前側取付位置"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "5.3N･m",
"WorkName": "交換台車支持部(右)4",
"WorkItems": [
"1. ①に②を③⑯⑰⑱で取付ける",
"2. 1完成品を④に⑲⑳㉑㉒で取付ける"
],
"WorkPoints": [
"面位置",
"矢印方向に押し当てて取付ける",
"長穴ｾﾝﾀｰに合せる",
"前側取付位置"
],
"Tolks": [
"締付ﾄﾙｸ 5.3N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.3N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "交換台車支持部(右)5",
"WorkItems": [
"1. ①にCOVER をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾄﾚｲ仕様",
"台車仕様",
"ﾄﾚｲ仕様",
"台車仕様"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"前側取付位置",
"後側取付位置"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "交換台車支持部(右)6",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける"
],
"WorkPoints": [
"面位置合せ"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20N･m",
"WorkName": "交換台車支持部(右)7",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付ける",
"2. 1完成品にCOVER をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "交換台車支持部(右)7",
"WorkItems": [],
"WorkPoints": [
"矢印方向に押し当てて取付ける",
"矢印方向に押し当てて取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｶﾞｲﾄﾞ組立30連/60連(前側&右側)1",
"WorkItems": [
"1. BRACKET にGUIDE をSPACER BOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"平行に取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｶﾞｲﾄﾞ組立30連/60連(前側&右側)2",
"WorkItems": [
"1. ①にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品30連/60連(前側&右側)",
"WorkItems": [
"1. H1工程へ払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｶﾞｲﾄﾞ組立30連/60連(後側&右側)1",
"WorkItems": [
"1. BRACKET にGUIDE をSPACER BOLT WASHER WASHER で取付ける"
],
"WorkPoints": [
"平行に取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｶﾞｲﾄﾞ組立30連/60連(後側&右側)2",
"WorkItems": [],
"WorkPoints": [
"面位置に取付の事",
"平行に取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"8㎜"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ組立30連/60連(後側&右側)2",
"WorkItems": [],
"WorkPoints": [
"面位置に取付の事",
"平行に取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"8㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法8.0㎜±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品30連/60連(後側&右側)",
"WorkItems": [
"1. PLUG を払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾑﾌｫﾛｱ部組立",
"WorkItems": [
"1. BRACKET の取付面(黄色部)に砥石を掛ける",
"2. 1完成品にCAM-FOLLOWER をWASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"CAM-FOLLOWER の付属ﾅｯﾄは廃棄して下さい",
"この作業では同じものを4個製作"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "油砥石",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.5㎜(BOX)",
"ToolOther": "150cN･m",
"WorkName": "ｶﾑﾌｫﾛｱ部組立",
"WorkItems": [
"2. 1完成品にCAM-FOLLOWER をWASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"CAM-FOLLOWER の付属ﾅｯﾄは廃棄して下さい"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備",
"WorkItems": [
"2. PLATE の平面度を測定する",
"1. PLATE の両面に㉖を掛ける"
],
"WorkPoints": [
"表面(座ｸﾞﾘ有)は特に表面に傷がつかない様に注意する事",
"PLATE に打痕やﾊﾞﾘが無い事",
"緑色部の9箇所を測定する事(平面度:0.1㎜以内)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"表 面",
"裏 面",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｱﾙﾐ用砥石",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備",
"WorkItems": [
"1. PLATE の両面に㉖を掛ける"
],
"WorkPoints": [
"表面(座ｸﾞﾘ有)は特に表面に傷がつかない様に注意する事",
"PLATE に打痕やﾊﾞﾘが無い事",
"緑色部の9箇所を測定する事(平面度:0.1㎜以内)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.1㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①",
"WorkItems": [
"1. GUIDE に㉖油砥石を掛ける",
"2. ①にGUIDE をBOLT で取付ける"
],
"WorkPoints": [
"GUIDE を㉗に押し当てて取付ける事",
"黄色部に㉖を掛ける",
"GUIDE の全面にﾊﾞﾘ､打痕等ないか確認する事",
"①の座ｸﾞﾘ面が無い方面に取付ける事",
"㉗ナットの向きに注意してピンを①まで挿入して取付ける",
"座ぐり穴の所にBOLT を入れる"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "油砥石",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①",
"WorkItems": [
"1. GUIDE に㉖油砥石を掛ける",
"2. ①にGUIDE をBOLT で取付ける"
],
"WorkPoints": [
"GUIDE を㉗に押し当てて取付ける事",
"黄色部に㉖を掛ける",
"GUIDE の全面にﾊﾞﾘ､打痕等ないか確認する事",
"①の座ｸﾞﾘ面が無い方面に取付ける事",
"座ぐり穴の所にBOLT を入れる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-①",
"WorkItems": [
"1. GUIDE に㉖油砥石を掛ける",
"2. ①にGUIDE をBOLT で取付ける"
],
"WorkPoints": [
"GUIDE を㉗に押し当てて取付ける事",
"黄色部に㉖を掛ける",
"GUIDE の全面にﾊﾞﾘ､打痕等ないか確認する事",
"①の座ｸﾞﾘ面が無い方面に取付ける事",
"座ぐり穴の所にBOLT を入れる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-②",
"WorkItems": [
"1. ①に②をBOLT で取付ける"
],
"WorkPoints": [
"座ぐり穴の所にBOLT を入れる",
"②を㉘に押し当てて（黄線）取付ける事",
"㉘を取付ける㉘の向き（ナット、切り欠き）に注意"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-②",
"WorkItems": [
"1. ①に②をBOLT で取付ける"
],
"WorkPoints": [
"座ぐり穴の所にBOLT を入れる",
"②を㉘に押し当てて（黄線）取付ける事",
"㉘を取付ける㉘の向き（ナット、切り欠き）に注意"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK のDｶｯﾄの位置に注意して取付ける事",
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"赤色部に㉖を掛ける（面取りが無い側）",
"座ぐり穴の所にBOLT を入れる",
"㉙でBLOCK を位置決め"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"面取り",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "油砥石",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK のDｶｯﾄの位置に注意して取付ける事",
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"赤色部に㉖を掛ける（面取りが無い側）",
"座ぐり穴の所にBOLT を入れる"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-③",
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK のDｶｯﾄの位置に注意して取付ける事",
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"赤色部に㉖を掛ける（面取りが無い側）",
"座ぐり穴の所にBOLT を入れる"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-④",
"WorkItems": [
"1. ①にGUIDE をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"GUIDE は各々外側(矢印方向)に寄せて取付ける事",
"座ぐり穴の所にBOLT を入れる"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾑﾌｫﾛｱ部組立-②",
"WorkItems": [
"1. BRACKET の取付面(黄色部)に砥石を掛ける",
"2. 1完成品にCAM-FOLLOWER をWASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"CAM-FOLLOWER の付属ﾅｯﾄは廃棄して下さい",
"この作業では同じものを4個製作"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "油砥石",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.5㎜(BOX)",
"ToolOther": "150cN･m",
"WorkName": "ｶﾑﾌｫﾛｱ部組立-②",
"WorkItems": [
"2. 1完成品にCAM-FOLLOWER をWASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"CAM-FOLLOWER の付属ﾅｯﾄは廃棄して下さい"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立準備-②",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"表 面",
"裏 面"
]
} | {
"QualityItem": "平行度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "0.1㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-⑤",
"WorkItems": [
"1. GUIDE に㉖油砥石を掛ける",
"2. ①にGUIDE をBOLT で取付ける"
],
"WorkPoints": [
"GUIDE を㉗に押し当てて取付ける事",
"黄色部に㉖を掛ける",
"GUIDE の全面にﾊﾞﾘ､打痕等ないか確認する事",
"①の座ｸﾞﾘ面が無い方面に取付ける事",
"㉗ナットの向きに注意してピンを①まで挿入して取付ける",
"座ぐり穴の所にBOLT を入れる"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを4個製作"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "油砥石",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-⑤",
"WorkItems": [
"1. GUIDE に㉖油砥石を掛ける",
"2. ①にGUIDE をBOLT で取付ける"
],
"WorkPoints": [
"黄色部に㉖を掛ける",
"GUIDE の全面にﾊﾞﾘ､打痕等ないか確認する事",
"①の座ｸﾞﾘ面が無い方面に取付ける事",
"㉗ナットの向きに注意してピンを①まで挿入して取付ける",
"座ぐり穴の所にBOLT を入れる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを4個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-⑤",
"WorkItems": [
"1. GUIDE に㉖油砥石を掛ける",
"2. ①にGUIDE をBOLT で取付ける"
],
"WorkPoints": [
"黄色部に㉖を掛ける",
"GUIDE の全面にﾊﾞﾘ､打痕等ないか確認する事",
"①の座ｸﾞﾘ面が無い方面に取付ける事",
"㉗ナットの向きに注意してピンを①まで挿入して取付ける",
"座ぐり穴の所にBOLT を入れる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを4個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "13.5㎜",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-⑥",
"WorkItems": [
"1. ①に②をBOLT で取付ける"
],
"WorkPoints": [
"座ぐり穴の所にBOLT を入れる",
"㉘で②カムフォロアと①の端面を合わせて締付け"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "作業指示通り出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-⑥",
"WorkItems": [
"1. ①に②をBOLT で取付ける"
],
"WorkPoints": [
"座ぐり穴の所にBOLT を入れる",
"㉘で②カムフォロアと①の端面を合わせて締付け"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-⑦",
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK のDｶｯﾄの位置に注意して取付ける事",
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"赤色部に㉖を掛ける（面取りが無い側）",
"座ぐり穴の所にBOLT を入れる",
"㉙でBLOCK を位置決め"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"面取り",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､ｶｴﾘ等無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "油砥石",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "下受けﾋﾟﾝ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5626",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-⑦",
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"赤色部に㉖を掛ける（面取りが無い側）",
"座ぐり穴の所にBOLT を入れる"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5626",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-⑦",
"WorkItems": [
"2. ①にBLOCK をBOLT で取付ける",
"1. BLOCK に㉖油砥石を掛ける"
],
"WorkPoints": [
"BLOCK の全面にﾊﾞﾘ､打痕等ないか確認する事",
"赤色部に㉖を掛ける（面取りが無い側）",
"座ぐり穴の所にBOLT を入れる"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "250cN･m",
"WorkName": "ｻﾎﾟｰﾄﾌﾟﾚｰﾄ組立-⑧",
"WorkItems": [
"1. ①にGUIDE をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"GUIDE は各々外側(矢印方向)に寄せて取付ける事",
"座ぐり穴の所にBOLT を入れる"
],
"Tolks": [
"締付ﾄﾙｸ 250cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "250cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "前面ｶﾊﾞｰ組立30連/60連(LCRﾁｪｯｶｰ仕様)",
"WorkItems": [
"1. COVER にLABEL を貼付ける",
"2. JOINT を払い出す"
],
"WorkPoints": [
"気泡無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"128㎜",
"10㎜"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "前面ｶﾊﾞｰ組立1",
"WorkItems": [
"◆1. 貼付け面を清掃",
"2. COVER にLABEL LABEL を張り付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"70㎜",
"◆作業者安全作業"
]
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "前面ｶﾊﾞｰ組立2",
"WorkItems": [
"1. ①にBOLT WASHER を差込む",
"2. 作業1完成品にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "前面ｶﾊﾞｰ組立3",
"WorkItems": [
"1. ①にSPACER SPRING WASHER をBOLT で取付",
"2. 作業1完成品にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "T10",
"ToolOther": "130cN･m",
"WorkName": "前面ｶﾊﾞｰ組立4",
"WorkItems": [
"1. ①にACTUATOR をNUT-PLATE BOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 130cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "130cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前面ｶﾊﾞｰ安全ｽｲｯﾁ組立1",
"WorkItems": [
"◆1. 貼付け面を脱脂する",
"2. BRACKET にCOVER を張り付ける"
],
"WorkPoints": [
"上面図",
"面位置で合わせ貼付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "張付け確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "面位置で貼付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "T10",
"ToolOther": "130cN･m",
"WorkName": "前面ｶﾊﾞｰ安全ｽｲｯﾁ組立2",
"WorkItems": [
"2. ①にSWITCH(660MM) をBOLT にて取付",
"3. 作業1完成品にCOVER をBOLT WASHER にて取付",
"■1. SWITCH(660MM) の型式確認､ﾛｯﾄNo.を記入する"
],
"WorkPoints": [
"SWITCH(660MM) ｽｲｯﾁの向きに注意する"
],
"Tolks": [
"締付ﾄﾙｸ 130cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:安全ｽｲｯﾁの型式確認とﾛｯﾄNo.記録",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "130cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "前面ｶﾊﾞｰ安全ｽｲｯﾁ組立2",
"WorkItems": [],
"WorkPoints": [
"SWITCH(660MM) ｽｲｯﾁのﾌﾀを取り外す※外した蓋は廃棄"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"型式",
"ﾛｯﾄNo.",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前面ｶﾊﾞｰ安全ｽｲｯﾁ組立2",
"WorkItems": [
"2. ①にSWITCH(660MM) をBOLT にて取付",
"3. 作業1完成品にCOVER をBOLT WASHER にて取付",
"■1. SWITCH(660MM) の型式確認､ﾛｯﾄNo.を記入する"
],
"WorkPoints": [
"SWITCH(660MM) ｽｲｯﾁの向きに注意する",
"SWITCH(660MM) ｽｲｯﾁのﾌﾀを取り外す※外した蓋は廃棄"
],
"Tolks": [
"締付ﾄﾙｸ 130cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "WETE-G002-C17",
"InspectionItems": [
"検査表①:安全ｽｲｯﾁの型式確認とﾛｯﾄNo.記録"
],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"型式",
"ﾛｯﾄNo.",
"WETE-G002-C17"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式を確認する事",
"Method": "目視",
"RecordMethod": "WETE-G002-C17",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前面ｶﾊﾞｰ安全ｽｲｯﾁ組立2",
"WorkItems": [
"2. ①にSWITCH(660MM) をBOLT にて取付",
"3. 作業1完成品にCOVER をBOLT WASHER にて取付",
"■1. SWITCH(660MM) の型式確認､ﾛｯﾄNo.を記入する"
],
"WorkPoints": [
"SWITCH(660MM) ｽｲｯﾁの向きに注意する",
"SWITCH(660MM) ｽｲｯﾁのﾌﾀを取り外す※外した蓋は廃棄"
],
"Tolks": [
"締付ﾄﾙｸ 130cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"検査表①:安全ｽｲｯﾁの型式確認とﾛｯﾄNo.記録",
"型式",
"ﾛｯﾄNo.",
"WETE-G002-C17"
]
} | {
"QualityItem": "ﾛｯﾄNo.記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾛｯﾄNo.を記録する事",
"Method": "目視",
"RecordMethod": "WETE-G002-C17",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "払い出し",
"WorkItems": [
"1. ①②BOLT WASHER を H1工程 に払い出し"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾍﾞｱ取付け",
"WorkItems": [
"1. ①をNUT-PLATE BOLT WASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"矢印方向に押し当てて取付けの事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｱ配線引き回し1",
"WorkItems": [
"1. ﾍﾞｱ配線を引き回す"
],
"WorkPoints": [
"板金に固定する",
"ﾘﾌﾄを上下させ干渉が無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管に負荷無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "50cN･m",
"WorkName": "ﾍﾞｱ配線引き回し2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. BRACKET にﾓｰﾀ動力線をBOLT WASHER NUT で取付ける",
"2. 1完成品をBOLT WASHER で取付ける",
"締付ﾄﾙｸ 194cN･m"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾍﾞｱ配線引き回し2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. BRACKET にﾓｰﾀ動力線をBOLT WASHER NUT で取付ける",
"2. 1完成品をBOLT WASHER で取付ける",
"締付ﾄﾙｸ 194cN･m"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｱ配線引き回し2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1. BRACKET にﾓｰﾀ動力線をBOLT WASHER NUT で取付ける",
"締付ﾄﾙｸ 50cN･m",
"ﾅｯﾄを挿入し取付ける",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"2. 1完成品をBOLT WASHER で取付ける",
"締付ﾄﾙｸ 194cN･m",
"3. 配線の引き回し･接続を行う",
"検査表BRACKET :4.ｺﾈｸﾀ接続確認ﾁｪｯｸ3",
"M402P/R",
"B1302P/R",
"1B1303P/R",
"1B1322P/R",
"E402P/R",
"WEPJ-G002-D33"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D33",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "1.5N･m",
"WorkName": "配線引き回し1",
"WorkItems": [
"2. 配線引き回し終了後､配線押さえを固定する"
],
"WorkPoints": [
"A矢視",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄに干渉し無い事",
"B401R",
"M401R",
"E401P/R"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し1",
"WorkItems": [
"1. 配線を引き回し固定する",
"2. 配線引き回し終了後､配線押さえを固定する"
],
"WorkPoints": [
"A矢視",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄに干渉し無い事",
"B401R",
"M401R",
"E401P/R",
"1B1320R",
"B1301R"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "WEPJ-G002-D33",
"InspectionItems": [
"検査表①:4.ｺﾈｸﾀ接続確認ﾁｪｯｸ1"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WEPJ-G002-D33"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D33",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し2",
"WorkItems": [
"1. 配線を引き回しｺﾈｸﾀを接続する"
],
"WorkPoints": [
"R401",
"R402",
"R403",
"R404",
"S01R",
"S301P/R"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D33",
"InspectionItems": [
"検査表①:ｺﾈｸﾀ接続確認ﾁｪｯｸ1･5"
],
"WorkTypes": [],
"Words": [
"WEPJ-G002-D33"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D33",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し3",
"WorkItems": [
"1. ﾍﾞｱ配線を引き回しｺﾈｸﾀを接続する"
],
"WorkPoints": [
"CN32K302",
"CN33K302",
"CNP3BK401",
"CN2BK401",
"CNP3BK401",
"CN2BK401",
"CN32/33K302",
"初めにCN2BK401のｹｰﾌﾞﾙを配線し1本だけﾏｳﾝﾄに固定する(EMC対策で必要)"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D33",
"InspectionItems": [
"検査表①:3-1.ﾓｰﾀﾄﾞﾗｲﾊﾞ接続確認"
],
"WorkTypes": [],
"Words": [
"検査表①:3-3.HCOM-IO基板接続確認",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WEPJ-G002-D33"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D33",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "中継基板取付治具(搬送基板用)",
"Size": "",
"ToolOther": "FM-*",
"WorkName": "配線引き回し4",
"WorkItems": [
"1. 補給･ｼｬｯﾀｰの配線を引き回しｺﾈｸﾀを接続する"
],
"WorkPoints": [
"1S01R",
"CN30K302"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-D33",
"InspectionItems": [
"検査表①:3-3.HCOM-IO基板接続確認"
],
"WorkTypes": [],
"Words": [
"検査表①:4.ｺﾈｸﾀ接続確認ﾁｪｯｸ6",
"WEPJ-G002-D33"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-*",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D33",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線固定1",
"WorkItems": [
"1. 配線を固定する"
],
"WorkPoints": [
"余長配線を丸めて固定する",
"配管と一緒に固定する",
"TP軸動力線のみ固定",
"配管と一緒に固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線固定2",
"WorkItems": [
"1. 配線を固定する"
],
"WorkPoints": [
"TP軸動力線のみ固定",
"動力線同士を固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "配線固定3",
"WorkItems": [
"1. ①の配管の先端から240㎜の位置にﾏｰｷﾝｸﾞする",
"2. 1完成品の配線･配管を固定する",
"1. ①の配管の先端から240㎜の位置にﾏｰｷﾝｸﾞする",
"2. 1完成品の配線･配管を固定する"
],
"WorkPoints": [
"それぞれの黄色ﾏｰｷﾝｸﾞ位置で固定する",
"配管先端",
"それぞれの黄色ﾏｰｷﾝｸﾞ位置で固定する",
"配管先端"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線固定3",
"WorkItems": [
"1. ①の配管の先端から240㎜の位置にﾏｰｷﾝｸﾞする",
"2. 1完成品の配線･配管を固定する"
],
"WorkPoints": [
"電源線",
"信号線",
"それぞれの黄色ﾏｰｷﾝｸﾞ位置で固定する",
"配管先端"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
} | {
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "3.2N･m",
"WorkName": "FAN取付け",
"WorkItems": [
"1. ①に②を取付ける",
"2. 1完成品の配線を引き回し､ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"前準備で取付けたﾎﾞﾙﾄ･ﾜｯｼｬｰを使用して取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:4.ｺﾈｸﾀ接続確認ﾁｪｯｸ1"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "FAN取付け",
"WorkItems": [
"1. ①に②を取付ける",
"2. 1完成品の配線を引き回し､ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"前準備で取付けたﾎﾞﾙﾄ･ﾜｯｼｬｰを使用して取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:4.ｺﾈｸﾀ接続確認ﾁｪｯｸ1"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN取付け",
"WorkItems": [
"1. ①に②を取付ける",
"2. 1完成品の配線を引き回し､ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"前準備で取付けたﾎﾞﾙﾄ･ﾜｯｼｬｰを使用して取付ける",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄへの干渉無き事",
"G101R"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "WEPJ-G002-D33",
"InspectionItems": [
"検査表①:4.ｺﾈｸﾀ接続確認ﾁｪｯｸ1"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WEPJ-G002-D33"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D33",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前段取り1",
"WorkItems": [
"■1. ANALYZER の型式を確認する",
"■2. ANALYZER の型式を確認する"
],
"WorkPoints": [
"この部分の型式を確認する",
"この部分の型式を確認する",
"使用しないため廃棄する",
"SD-EJM2FB1-604にて使用"
],
"Tolks": [],
"InspectionNo": "WEETE-G002-A03",
"InspectionItems": [
"検査表ANALYZER :APD.1 型式確認",
"検査表ANALYZER :APD.1 型式確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"WEETE-G002-A03"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致している事",
"Method": "目視",
"RecordMethod": "WEETE-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前段取り2",
"WorkItems": [
"1. ①②のｽｲｯﾁを設定する"
],
"WorkPoints": [
"B2004",
"B2005",
"bit1:OFFbit2:OFFbit3:ONbit4:ONbit5:ONbit6:OFFbit7:OFFbit8:OFF",
"bit1:OFFbit2:OFFbit3:ONbit4:ONbit5:ONbit6:OFFbit7:OFFbit8:OFF"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:APD.2 ｽｲｯﾁ設定確認",
"WETE-G002-A03"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前段取り3",
"WorkItems": [
"■1. SENSOR SENSOR SENSOR SENSOR SENSOR の型式を確認する"
],
"WorkPoints": [
"この部分の型式を確認する"
],
"Tolks": [],
"InspectionNo": "WEETE-G002-A03",
"InspectionItems": [
"検査表SENSOR :APD.1 型式確認"
],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"WEETE-G002-A03"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致している事",
"Method": "目視",
"RecordMethod": "WEETE-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前段取り4",
"WorkItems": [
"2. 1完成品に④を貼付ける",
"1. ①②③を接続する"
],
"WorkPoints": [
"ﾚﾊﾞｰを下げてﾛｯｸする",
"ﾕﾆｯﾄ接続部に貼付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "55cN･m",
"WorkName": "前段取り5",
"WorkItems": [
"■1. ①にCABLE CABLE CABLE ⑥⑦⑧⑨⑩を接続する"
],
"WorkPoints": [
"空き端子も締結すること",
"A1_B2004",
"A2_B2004",
"A6_B2004",
"A9_B2004",
"B1_B2004",
"B2_B2004",
"B6_B2004",
"B9_B2004",
"6_B2003",
"7_B2003",
"8_B2003",
"9_B2003",
"締結後ｶﾊﾞｰをすること",
"3b",
"3b",
"A5a_B2004/5b",
"A8a_B2004/8b",
"B8a_B2004/8b",
"B2_B2005",
"3b",
"5b",
"B8a_B2005/8b",
"B9_B2005",
"3b-5b-8b",
"B2/B8a/B9_B2004",
"B1/B5a/B6_B2004",
"A2/A8a/A9_B2004",
"A1/A5a/A6_B2004",
"B2/B8a/B9_B2005",
"B5a_B2004/5b"
],
"Tolks": [
"締付ﾄﾙｸ 55cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:APD.4 丸端子接続確認",
"検査表①:APD.5 ねじ締めﾄﾙｸ確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "55cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前段取り5",
"WorkItems": [
"■1. ①にCABLE CABLE CABLE ⑥⑦⑧⑨⑩を接続する"
],
"WorkPoints": [
"空き端子も締結すること",
"A1_B2004",
"A2_B2004",
"A6_B2004",
"A9_B2004",
"B1_B2004",
"B2_B2004",
"B6_B2004",
"B9_B2004",
"6_B2003",
"7_B2003",
"8_B2003",
"9_B2003",
"締結後ｶﾊﾞｰをすること",
"3b",
"3b",
"A5a_B2004/5b",
"A8a_B2004/8b",
"B8a_B2004/8b",
"B2_B2005",
"3b",
"5b",
"B8a_B2005/8b",
"B9_B2005",
"3b-5b-8b",
"B2/B8a/B9_B2004",
"B1/B5a/B6_B2004",
"A2/A8a/A9_B2004",
"A1/A5a/A6_B2004",
"B2/B8a/B9_B2005",
"B5a_B2004/5b"
],
"Tolks": [
"締付ﾄﾙｸ 55cN･m"
],
"InspectionNo": "WETE-G002-A03",
"InspectionItems": [
"検査表①:APD.4 丸端子接続確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:APD.5 ねじ締めﾄﾙｸ確認",
"WETE-G002-A03"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-A03",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.