Datasets:
ayuzawa
/
ManageProcess21

Dataset card Data Studio Files
xet
 Community
1
input
stringclasses
1 value
instruction
stringlengths
223
3.4k
output
stringlengths
206
380
category
stringclasses
1 value
index
stringclasses
1 value
fileName
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.1", "ToolOther": "26cN･m", "WorkName": "ｴﾝｺｰﾀﾞｰ配線の接続", "WorkItems": [ "1. ①のｴﾝｺｰﾀﾞｰ配線を引き回し､ｺﾈｸﾀに接続する" ], "WorkPoints": [ "CN5K302", "CN3K302", "CN4K302", "照明の配線は後工程で引き回すのでまとめておく" ], "Tolks": [ "締付ﾄﾙｸ 26cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "検査表①:接続ﾁｪｯｸ_ｴﾝｺｰﾀﾞ中継基板" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "26cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "1.94N･m", "WorkName": "上面ﾌﾟﾚｰﾄ取付", "WorkItems": [ "1. ①に②をBOLT とBOLT WASHER で取付ける" ], "WorkPoints": [ "①のﾋﾟﾝに②を載せて取付ける事", "①の裏面よりBOLT WASHER を取付ける事", "①のﾋﾟﾝが②に当付けられている事" ], "Tolks": [ "締付ﾄﾙｸ 1.94N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "1.94N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "3.2N･m", "WorkName": "CPU-BOX取付", "WorkItems": [ "2. ①に⑥をBOLT WASHER ､WASHER BOLT で取付ける", "■1. ⑥の型式を確認し､ｼﾘｱﾙNoを検査表記入する" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m", "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業", "■安全作業" ], "Words": [ "検査表①:型式･検査書ﾁｪｯｸ", "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.2N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "6.0N･m", "WorkName": "CPU-BOX取付", "WorkItems": [ "2. ①に⑥をBOLT WASHER ､WASHER BOLT で取付ける", "■1. ⑥の型式を確認し､ｼﾘｱﾙNoを検査表記入する" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m", "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業", "■安全作業" ], "Words": [ "検査表①:型式･検査書ﾁｪｯｸ", "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "6.0N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "CPU-BOX取付", "WorkItems": [ "2. ①に⑥をBOLT WASHER ､WASHER BOLT で取付ける", "■1. ⑥の型式を確認し､ｼﾘｱﾙNoを検査表記入する" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.2N･m", "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:型式･検査書ﾁｪｯｸ" ], "WorkTypes": [ "■安全作業", "■安全作業" ], "Words": [ "2LC-JG-23015" ] }
{ "QualityItem": "型式･ｼﾘｱﾙ番号確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認検査書有無確認", "Method": "目視", "RecordMethod": "2LC-JG-23015", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "3㎜", "ToolOther": "1.94N･m", "WorkName": "ACｲﾝﾚｯﾄ取付", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1. ①に②をBOLT WASHER で取付ける", "締付ﾄﾙｸ 1.94N･m" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "1.94N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ACｲﾝﾚｯﾄ取付", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "AC配線は後工程で引き回すので丸めておく事", "2. ①にSOFTWARE-LICENSE SOFTWARE-LICENSE を貼付ける", "検査表①:12.ﾗｲｾﾝｽﾗﾍﾞﾙの確認", "CPU BOXに貼付けてある場合は作業不要ｼｰﾙが配膳されている場合は返却のこと" ] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "CPU-BOXAC配線引き回し1", "WorkItems": [ "2. ACｲﾝﾚｯﾄの配線と一緒に上面ﾌﾟﾚｰﾄ側に引き回し､ｲﾝｼｭﾛｯｸで結束する", "■1. ①にCABLE を接続する" ], "WorkPoints": [ "1aF101と3aF101はﾌﾞﾚｰｶｰへ", "4X02はｱｰｽﾌﾟﾚｰﾄへ", "接続後､抜け防止でﾛｯｸする", "AC(N)bT101とAC(L)bT101は24V電源へ", "被覆の端面で結束する事" ], "Tolks": [], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:CPU BOX確認" ], "WorkTypes": [ "■安全作業", "■安全作業" ], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "2LC-JG-23015" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "2LC-JG-23015", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "250cN･m", "WorkName": "CPU-BOXAC配線引き回し2", "WorkItems": [ "2. 付属のｶﾊﾞｰを取付ける", "■1. ①のﾌﾞﾚｰｶｰに配線を接続する" ], "WorkPoints": [ "接続間違いに注意", "ｶﾁｯと音がするまで差込む事" ], "Tolks": [ "締付ﾄﾙｸ 250cN･m" ], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ" ], "WorkTypes": [ "■安全作業" ], "Words": [ "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "250cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.1", "ToolOther": "50cN･m", "WorkName": "CPU-BOXAC配線引き回し2", "WorkItems": [ "3. ①にCOVER をSCREW で取付ける" ], "WorkPoints": [ "1aF101", "3aF101" ], "Tolks": [ "締付ﾄﾙｸ 50cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [ "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "50cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "160cN･m", "WorkName": "CPU-BOXAC配線引き回し3", "WorkItems": [ "■2. ｱｰｽﾌﾟﾚｰﾄに配線をSCREW で接続する", "■1. ①の24V電源に配線を接続する" ], "WorkPoints": [ "背合せで取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 160cN･m", "締付ﾄﾙｸ 180cN･m" ], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:ﾈｼﾞ締めﾄﾙｸ", "検査表①:ﾈｼﾞ締めﾄﾙｸ" ], "WorkTypes": [ "■安全作業" ], "Words": [ "検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ", "検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ", "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "160cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.1", "ToolOther": "180cN･m", "WorkName": "CPU-BOXAC配線引き回し3", "WorkItems": [ "■2. ｱｰｽﾌﾟﾚｰﾄに配線をSCREW で接続する", "■1. ①の24V電源に配線を接続する" ], "WorkPoints": [ "背合せで取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 160cN･m", "締付ﾄﾙｸ 180cN･m" ], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ", "検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ" ], "WorkTypes": [ "■安全作業" ], "Words": [ "検査表①:ﾈｼﾞ締めﾄﾙｸ", "検査表①:ﾈｼﾞ締めﾄﾙｸ", "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "180cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "CPU-BOXAC配線引き回し3", "WorkItems": [ "■2. ｱｰｽﾌﾟﾚｰﾄに配線をSCREW で接続する", "■1. ①の24V電源に配線を接続する" ], "WorkPoints": [ "AC(N)aT101AC(N)bT101", "4X02", "AC(L)aT101AC(L)bT101", "背合せで取付ける事", "1X02" ], "Tolks": [ "締付ﾄﾙｸ 160cN･m", "締付ﾄﾙｸ 180cN･m" ], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:ﾈｼﾞ締めﾄﾙｸ", "検査表①:ﾈｼﾞ締めﾄﾙｸ" ], "WorkTypes": [ "■安全作業" ], "Words": [ "検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ", "検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ", "2LC-JG-23015" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "2LC-JG-23015", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "160cN･m", "WorkName": "DC配線引き回し", "WorkItems": [ "2. 配線を引き回しｺﾈｸﾀへ接続する", "■1. ①の24V電源にCABLE の配線を接続する" ], "WorkPoints": [ "+V2aT101", "-V2aT101-V2bT101", "ｶﾁｯと音がするまで差込む事", "背合せで取付ける事" ], "Tolks": [ "締付ﾄﾙｸ 160cN･m" ], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:ﾈｼﾞ締めﾄﾙｸ" ], "WorkTypes": [ "■安全作業" ], "Words": [ "検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ", "検査表①:ｴﾝｺｰﾀﾞ中継基板", "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "160cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "DC配線引き回し", "WorkItems": [ "2. 配線を引き回しｺﾈｸﾀへ接続する", "■1. ①の24V電源にCABLE の配線を接続する" ], "WorkPoints": [ "+V2aT101", "-V2aT101-V2bT101", "ｶﾁｯと音がするまで差込む事", "背合せで取付ける事", "ここの穴から下に通す" ], "Tolks": [ "締付ﾄﾙｸ 160cN･m" ], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:接続ﾁｪｯｸ_ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ" ], "WorkTypes": [ "■安全作業" ], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "検査表①:ﾈｼﾞ締めﾄﾙｸ", "検査表①:ｴﾝｺｰﾀﾞ中継基板", "2LC-JG-23015" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "2LC-JG-23015", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "MC-S取付①", "WorkItems": [ "■1. ②の型式を確認し､ｼﾘｱﾙNoを検査書に記入する", "◆2. ①に②をBOLT WASHER NUT で仮止めする" ], "WorkPoints": [ "①の開口部に⑥の配線を挟み込まない様に注意する事", "①の開口部やXYZﾃｰﾌﾞﾙに②を干渉させない様に注意して取付ける事", "左右4箇所仮締めする事", "本締工程:SD-A046607-515", "二人作業" ], "Tolks": [], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:型式･検査書ﾁｪｯｸ" ], "WorkTypes": [ "◆作業者安全作業", "■安全作業", "■安全作業" ], "Words": [ "2LC-JG-23015" ] }
{ "QualityItem": "型式･ｼﾘｱﾙ番号確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認ｼﾘｱﾙNo.転記", "Method": "目視", "RecordMethod": "2LC-JG-23015", "Other": "-", "ProcessNames": [ "安全工程", "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "MC-S取付①", "WorkItems": [ "■1. ②の型式を確認し､ｼﾘｱﾙNoを検査書に記入する", "◆2. ①に②をBOLT WASHER NUT で仮止めする" ], "WorkPoints": [ "①の開口部に⑥の配線を挟み込まない様に注意する事", "①の開口部やXYZﾃｰﾌﾞﾙに②を干渉させない様に注意して取付ける事", "左右4箇所仮締めする事", "本締工程:SD-A046607-515", "二人作業" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業", "■安全作業", "■安全作業" ], "Words": [ "検査表①:型式･検査書ﾁｪｯｸ" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "二人作業", "ProcessNames": [ "安全工程", "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "5㎜", "ToolOther": "9.8N･m", "WorkName": "MC-S取付②", "WorkItems": [ "2. 1完成品にCOVER を貼付ける", "3. MC-Sからの配線を引き回し固定する", "1. ①のMC-Sのﾌﾟﾚｰﾄと上面ﾌﾟﾚｰﾄの隙間を11㎜に調整し､仮締めﾎﾞﾙﾄを締結する" ], "WorkPoints": [ "COVER の貼付け位置を脱脂し､右端から5㎜の位置に貼付ける事" ], "Tolks": [ "締付ﾄﾙｸ 9.8N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "11㎜", "11㎜" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "9.8N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "Size": "11㎜", "ToolOther": "", "WorkName": "MC-S取付②", "WorkItems": [ "2. 1完成品にCOVER を貼付ける", "3. MC-Sからの配線を引き回し固定する", "1. ①のMC-Sのﾌﾟﾚｰﾄと上面ﾌﾟﾚｰﾄの隙間を11㎜に調整し､仮締めﾎﾞﾙﾄを締結する" ], "WorkPoints": [ "COVER の貼付け位置を脱脂し､右端から5㎜の位置に貼付ける事" ], "Tolks": [ "締付ﾄﾙｸ 9.8N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "11㎜", "11㎜" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "1回/3年", "ToolRecord": "校正成績書", "StdVal": "指示通り取付け出来ている事", "Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "MC-S取付②", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "5㎜", "ｺﾈｸﾀｰはﾌﾞﾗｹｯﾄに挿入する" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "LANｹｰﾌﾞﾙ引き回し", "WorkItems": [ "3. ①にCABLE を引き回す", "■1. CABLE のRoHSﾏｰｸを確認する", "2. CABLE にNOISE-FILTER を取付ける" ], "WorkPoints": [ "LAN1" ], "Tolks": [], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:CPU BOX確認", "検査表①:CPU BOX確認" ], "WorkTypes": [ "■安全作業" ], "Words": [ "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "60㎜", "検査表①:ﾌｪﾗｲﾄｺｱ", "2LC-JG-23015" ] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "RoHSﾏｰｸが貼付け出来ている事", "Method": "目視", "RecordMethod": "2LC-JG-23015", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "LANｹｰﾌﾞﾙ引き回し", "WorkItems": [ "3. ①にCABLE を引き回す", "■1. CABLE のRoHSﾏｰｸを確認する", "2. CABLE にNOISE-FILTER を取付ける" ], "WorkPoints": [ "LAN1" ], "Tolks": [], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:ﾌｪﾗｲﾄｺｱ" ], "WorkTypes": [ "■安全作業" ], "Words": [ "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "60㎜", "検査表①:CPU BOX確認", "検査表①:CPU BOX確認" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "LANｹｰﾌﾞﾙ引き回し", "WorkItems": [ "3. ①にCABLE を引き回す", "■1. CABLE のRoHSﾏｰｸを確認する", "2. CABLE にNOISE-FILTER を取付ける" ], "WorkPoints": [ "LAN1" ], "Tolks": [], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:CPU BOX確認", "検査表①:CPU BOX確認" ], "WorkTypes": [ "■安全作業" ], "Words": [ "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "60㎜", "検査表①:ﾌｪﾗｲﾄｺｱ", "2LC-JG-23015" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "2LC-JG-23015", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "照明配線引き回し", "WorkItems": [ "1. ①に照明配線を下から上面ﾌﾟﾚｰﾄまで引き回し､接続する" ], "WorkPoints": [ "1CN0E001R" ], "Tolks": [], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ" ], "WorkTypes": [], "Words": [ "2LC-JG-23015" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "2LC-JG-23015", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "150cN･m", "WorkName": "CP~MC-Sﾕﾆｯﾄ引き回し", "WorkItems": [ "2. CABLE を引き回し､MC-Sへ接続する", "■1. ①のCPにCABLE を接続する" ], "WorkPoints": [ "4aF102", "2aF102", "CN1K307" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:ﾈｼﾞ締めﾄﾙｸ" ], "WorkTypes": [ "■安全作業", "■安全作業" ], "Words": [ "検査表①:接続ﾁｪｯｸ ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ", "検査表①:接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ", "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "CP~MC-Sﾕﾆｯﾄ引き回し", "WorkItems": [ "2. CABLE を引き回し､MC-Sへ接続する", "■1. ①のCPにCABLE を接続する" ], "WorkPoints": [ "4aF102", "2aF102", "CN1K307" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:接続ﾁｪｯｸ ｵﾌﾗｲﾝｶﾒﾗﾕﾆｯﾄ" ], "WorkTypes": [ "■安全作業", "■安全作業" ], "Words": [ "検査表①:ﾈｼﾞ締めﾄﾙｸ", "検査表①:接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ", "2LC-JG-23015" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "2LC-JG-23015", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "No.2", "ToolOther": "180cN･m", "WorkName": "FG配線引き回し", "WorkItems": [ "■1. ①にCABLE をSCREW で固定する" ], "WorkPoints": [ "FGF1", "FGK", "横から見た図" ], "Tolks": [ "締付ﾄﾙｸ 180cN･m" ], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:ﾈｼﾞ締めﾄﾙｸ" ], "WorkTypes": [ "■安全作業" ], "Words": [ "検査表①:接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ", "■安全作業" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "180cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "FG配線引き回し", "WorkItems": [ "■1. ①にCABLE をSCREW で固定する" ], "WorkPoints": [ "FGF1", "FGK", "横から見た図" ], "Tolks": [ "締付ﾄﾙｸ 180cN･m" ], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ" ], "WorkTypes": [ "■安全作業" ], "Words": [ "検査表①:ﾈｼﾞ締めﾄﾙｸ", "2LC-JG-23015" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "2LC-JG-23015", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｴﾝｺｰﾀﾞ配線引き回し", "WorkItems": [ "1. ①にCABLE を引き回し､接続する" ], "WorkPoints": [ "CN2K302", "CN2K307", "ｶﾁｯと音がするまで差込む事" ], "Tolks": [], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ" ], "WorkTypes": [], "Words": [ "検査表①:ｴﾝｺｰﾀﾞ中継基板", "2LC-JG-23015" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "2LC-JG-23015", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾌｪﾗｲﾄｺｱ取付", "WorkItems": [ "■1. NOISE-FILTER ､FILTER の型式を確認する", "2. ①にNOISE-FILTER FILTER を取付ける", "3. ﾌｪﾗｲﾄｺｱがずれない様にｲﾝｼｭﾛｯｸで固定する(3箇所)", "4. LED照明配線のﾌｪﾗｲﾄｺｱとLANｹｰﾌﾞﾙのﾌｪﾗｲﾄｺｱをｲﾝｼｭﾛｯｸで固定する" ], "WorkPoints": [ "ｶﾁｯと音がするまで差込む事", "型式", "LED照明配線", "型式", "抜き窓から100mmの位置", "ｲﾝｼｭﾛｯｸから50mmの位置", "ｲﾝｼｭﾛｯｸから10mmの位置", "ｴﾝｺｰﾀﾞ配線", "AC配線" ], "Tolks": [], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:型式･検査書ﾁｪｯｸ" ], "WorkTypes": [ "■安全作業", "■安全作業" ], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "検査表①:ﾌｪﾗｲﾄｺｱの確認", "100㎜", "50㎜", "10㎜", "2LC-JG-23015" ] }
{ "QualityItem": "型式･ｼﾘｱﾙ番号確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式確認ｼﾘｱﾙNo.転記", "Method": "目視", "RecordMethod": "2LC-JG-23015", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾌｪﾗｲﾄｺｱ取付", "WorkItems": [ "■1. NOISE-FILTER ､FILTER の型式を確認する", "2. ①にNOISE-FILTER FILTER を取付ける", "3. ﾌｪﾗｲﾄｺｱがずれない様にｲﾝｼｭﾛｯｸで固定する(3箇所)" ], "WorkPoints": [ "ｶﾁｯと音がするまで差込む事", "型式", "LED照明配線", "型式", "抜き窓から100mmの位置", "ｲﾝｼｭﾛｯｸから50mmの位置", "ｲﾝｼｭﾛｯｸから10mmの位置", "ｴﾝｺｰﾀﾞ配線", "AC配線" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "■安全作業", "■安全作業" ], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "検査表①:型式･検査書ﾁｪｯｸ", "検査表①:ﾌｪﾗｲﾄｺｱの確認", "■安全作業" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±1㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "-ﾋﾞｯﾄ3㎜", "ToolOther": "15cN･m", "WorkName": "ｶﾒﾗ配線引き回し", "WorkItems": [ "1. ①にCABLE を引き回し､接続する", "2. CABLE にLABEL を取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 15cN･m" ], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ" ], "WorkTypes": [], "Words": [ "検査表①:CPU BOX確認", "LABEL の端面を当てて固定する" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "15cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ｶﾒﾗ配線引き回し", "WorkItems": [ "1. ①にCABLE を引き回し､接続する", "2. CABLE にLABEL を取付ける" ], "WorkPoints": [ "CN2K307", "CN2K303", "ｶﾁｯと音がするまで差込む事", "余長は下図のように引き回す", "CAMERAのﾗﾍﾞﾙがある方を接続する" ], "Tolks": [ "締付ﾄﾙｸ 15cN･m" ], "InspectionNo": "2LC-JG-23015", "InspectionItems": [ "検査表①:CPU BOX確認" ], "WorkTypes": [], "Words": [ "ｲﾝｼｭﾛｯｸ指示", "･ｹｰﾌﾞﾙ同士を固定", "･ﾀｲﾏｳﾝﾄに固定 又は板金に固定", "検査表①:接続ﾁｪｯｸ MC-Sﾕﾆｯﾄ", "LABEL の端面を当てて固定する", "2LC-JG-23015" ] }
{ "QualityItem": "接続確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り接続出来ている事", "Method": "目視", "RecordMethod": "2LC-JG-23015", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "MC-Sｶﾊﾞｰ取付", "WorkItems": [ "1. ①にCOVER をBOLT で取付ける" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾗﾍﾞﾙ貼付け-①", "WorkItems": [ "1. COVER の内側にLABEL を貼付ける" ], "WorkPoints": [ "貼付箇所を㉖で脱脂してから貼付ける事", "寸法や方向に注意して貼付ける事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "内側", "内側" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "背面ｶﾊﾞｰ取付", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1. ①に②をBOLT BOLT で取付ける", "締付ﾄﾙｸ 150cN･m", "削除" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾗﾍﾞﾙ貼付け-②", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1. ①にLABEL を貼付ける", "貼付箇所を㉖で脱脂してから貼付ける事", "寸法や方向に注意して貼付ける事" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "150cN･m", "WorkName": "上面ｶﾊﾞｰ取付", "WorkItems": [ "1. ①に⑥をBOLT で取付ける" ], "WorkPoints": [ "配線を挟み込まないように注意する事" ], "Tolks": [ "締付ﾄﾙｸ 150cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "150cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾗﾍﾞﾙ貼付け-③", "WorkItems": [ "1. ①にLABEL を貼付ける" ], "WorkPoints": [ "貼付箇所を㉖で拭き取り貼付ける事", "寸法や方向に注意して貼付ける事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:<完成品検査>ｷｯﾄ銘板" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾗﾍﾞﾙ貼付け-③", "WorkItems": [ "1. ①にLABEL を貼付ける" ], "WorkPoints": [ "貼付箇所を㉖で拭き取り貼付ける事", "寸法や方向に注意して貼付ける事" ], "Tolks": [], "InspectionNo": "2LC-JG-23004", "InspectionItems": [ "検査表①:<完成品検査>ｷｯﾄ銘板" ], "WorkTypes": [], "Words": [ "2LC-JG-23004" ] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り貼付出来ている事", "Method": "目視", "RecordMethod": "2LC-JG-23004", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "600㎜", "ToolOther": "", "WorkName": "ﾗﾍﾞﾙ貼付け-④", "WorkItems": [ "1. ①にLABEL を貼付ける" ], "WorkPoints": [ "貼付箇所を㉖で拭き取り貼付ける事", "寸法や方向に注意して貼付ける事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾗﾍﾞﾙ貼付け-⑤", "WorkItems": [ "1. ①にLABEL LABEL を貼付ける" ], "WorkPoints": [ "貼付箇所を㉖で拭き取り貼付ける事", "寸法や方向に注意して貼付ける事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾗﾍﾞﾙ貼付け-⑥", "WorkItems": [ "1. ①にLABEL ⑦を貼付ける" ], "WorkPoints": [ "貼付箇所を㉖で拭き取り貼付ける事", "寸法や方向に注意して貼付ける事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:<完成品検査>ｷｯﾄ銘板" ] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾗﾍﾞﾙ貼付け-⑥", "WorkItems": [ "1. ①にLABEL ⑦を貼付ける" ], "WorkPoints": [ "貼付箇所を㉖で拭き取り貼付ける事", "寸法や方向に注意して貼付ける事" ], "Tolks": [], "InspectionNo": "2LC-JG-23004", "InspectionItems": [ "検査表①:<完成品検査>ｷｯﾄ銘板" ], "WorkTypes": [], "Words": [ "2LC-JG-23004" ] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り貼付出来ている事", "Method": "目視", "RecordMethod": "2LC-JG-23004", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "ﾗﾍﾞﾙ貼付け-⑦", "WorkItems": [ "1. ①にLABEL を貼付ける" ], "WorkPoints": [ "貼付箇所を㉖で拭き取り貼付ける事", "寸法や方向に注意して貼付ける事" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "寸法確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ｻﾎﾟｰﾄﾌﾞﾗｹｯﾄﾗﾍﾞﾙ貼付け", "WorkItems": [ "◆1. ﾗﾍﾞﾙ貼付け部の油分を除去する", "2. STOPPER STOPPER STOPPER BRACKET へLABEL を指定の寸法で貼付ける" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "15㎜", "1㎜", "◆作業者安全作業" ] }
{ "QualityItem": "貼付位置確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示寸法各±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "2.5㎜", "ToolOther": "95cN･m", "WorkName": "固定ﾌﾞﾗｹｯﾄ組立", "WorkItems": [ "1. BRACKET にBOLT WASHER を差込み､②をBOLT WASHER にて取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 95cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [ "完成図" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "95cN･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "4㎜", "ToolOther": "3.6N･m", "WorkName": "固定ﾌﾞﾗｹｯﾄ組立", "WorkItems": [ "2. 作業1完成品にBRACKET をBOLT WASHER にて取付" ], "WorkPoints": [], "Tolks": [ "締付ﾄﾙｸ 3.6N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "3.6N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "150㎜", "ToolOther": "", "WorkName": "ﾌﾞﾛｯｸDﾋﾟﾝ圧入", "WorkItems": [ "1. BLOCK にPIN を圧入" ], "WorkPoints": [ "出代:5mm" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "◆作業者安全作業" ], "Words": [] }
{ "QualityItem": "出代確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "目安出代5㎜±0.5㎜", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "作業者安全工程" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部", "Size": "", "ToolOther": "FM-5712", "WorkName": "検査1‐①", "WorkItems": [ "1. ﾍｯﾄﾞ取付", "2. ﾁｪｯｶとﾍｯﾄﾞ取付けの隙間を確認", "3. 制御BOXの電源をONする" ], "WorkPoints": [ "背面4箇所固定", "0.1mm以下", "0.1mm以下" ], "Tolks": [ "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①FC08:ﾍｯﾄﾞﾁｪｯｶｰ確認", "検査表②FC03:ﾍｯﾄﾞﾁｪｯｶｰ確認" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-5712", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付けできている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "", "ToolOther": "6.0N･m", "WorkName": "検査1‐①", "WorkItems": [ "1. ﾍｯﾄﾞ取付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "6.0N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾍｯﾄﾞ取付けﾛﾝｸﾞﾋﾞｯﾄM5", "Size": "", "ToolOther": "FM-6090", "WorkName": "検査1‐①", "WorkItems": [ "1. ﾍｯﾄﾞ取付" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-6090", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付けできている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.1㎜", "ToolOther": "", "WorkName": "検査1‐①", "WorkItems": [ "2. ﾁｪｯｶとﾍｯﾄﾞ取付けの隙間を確認", "3. 制御BOXの電源をONする" ], "WorkPoints": [ "0.1mm以下", "0.1mm以下" ], "Tolks": [], "InspectionNo": "GWETJ-F013-001", "InspectionItems": [ "検査表①FC08:ﾍｯﾄﾞﾁｪｯｶｰ確認" ], "WorkTypes": [], "Words": [ "検査表②FC03:ﾍｯﾄﾞﾁｪｯｶｰ確認", "GWETJ-F013-001" ] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.1㎜以下", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "GWETJ-F013-001", "Other": "FC08の場合", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.1㎜", "ToolOther": "", "WorkName": "検査1‐①", "WorkItems": [ "2. ﾁｪｯｶとﾍｯﾄﾞ取付けの隙間を確認", "3. 制御BOXの電源をONする" ], "WorkPoints": [ "0.1mm以下", "0.1mm以下" ], "Tolks": [], "InspectionNo": "GWETP-F013-001", "InspectionItems": [ "検査表②FC03:ﾍｯﾄﾞﾁｪｯｶｰ確認" ], "WorkTypes": [], "Words": [ "検査表①FC08:ﾍｯﾄﾞﾁｪｯｶｰ確認", "GWETP-F013-001" ] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.1㎜以下", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "GWETP-F013-001", "Other": "FC03の場合", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部", "Size": "", "ToolOther": "FM-5712", "WorkName": "検査1‐②", "WorkItems": [ "1. ﾍｯﾄﾞ取付", "2. ﾁｪｯｶとﾍｯﾄﾞ取付けの隙間を確認", "3. 制御BOXの電源をONする" ], "WorkPoints": [ "背面4箇所固定", "0.1mm以下" ], "Tolks": [ "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①FC16:19.ﾍｯﾄﾞﾁｪｯｶｰ確認" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-5712", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付けできている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "", "ToolOther": "6.0N･m", "WorkName": "検査1‐②", "WorkItems": [ "1. ﾍｯﾄﾞ取付" ], "WorkPoints": [ "背面4箇所固定" ], "Tolks": [ "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "6.0N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾍｯﾄﾞ取付けﾛﾝｸﾞﾋﾞｯﾄM5", "Size": "", "ToolOther": "FM-6090", "WorkName": "検査1‐②", "WorkItems": [ "1. ﾍｯﾄﾞ取付" ], "WorkPoints": [ "背面4箇所固定" ], "Tolks": [ "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-6090", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付けできている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ", "Size": "0.1㎜", "ToolOther": "", "WorkName": "検査1‐②", "WorkItems": [], "WorkPoints": [ "0.1mm以下" ], "Tolks": [], "InspectionNo": "GWEHD-F013-001", "InspectionItems": [], "WorkTypes": [], "Words": [ "GWEHD-F013-001" ] }
{ "QualityItem": "隙間確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "0.1㎜以下", "Method": "ｼｯｸﾈｽｹﾞｰｼﾞ", "RecordMethod": "GWEHD-F013-001", "Other": "FC16の場合", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部", "Size": "", "ToolOther": "FM-5712", "WorkName": "検査2", "WorkItems": [ "1. ﾁｪｯｶｿﾌﾄを起動", "2. 検査員を設定し[OK]を押す", "3. 検査員ﾓｰﾄﾞを押す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "画面確認", "ToolManageNo": "FM-5712", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部", "Size": "", "ToolOther": "FM-5712", "WorkName": "検査3", "WorkItems": [ "1. 真空ﾎﾟﾝﾌﾟがOFFしていることを確認し[OK]を押す", "2. ﾉｽﾞﾙﾁｪﾝｼﾞｬにﾉｽﾞﾙがあることを確認し[OK]を押す" ], "WorkPoints": [ "FC03はﾉｽﾞﾙﾁｪﾝｼﾞｬ確認は無し" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "画面確認", "ToolManageNo": "FM-5712", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "真空ﾎﾟﾝﾌﾟﾕﾆｯﾄ", "Size": "", "ToolOther": "FM-0560", "WorkName": "検査3", "WorkItems": [ "1. 真空ﾎﾟﾝﾌﾟがOFFしていることを確認し[OK]を押す", "2. ﾉｽﾞﾙﾁｪﾝｼﾞｬにﾉｽﾞﾙがあることを確認し[OK]を押す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-0560", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "OFFしている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部", "Size": "", "ToolOther": "FM-5712", "WorkName": "検査4", "WorkItems": [ "1. [取付完了]を押す", "2. 真空ﾎﾟﾝﾌﾟの電源をONし､[OK]を押す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "画面確認", "ToolManageNo": "FM-5712", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "真空ﾎﾟﾝﾌﾟﾕﾆｯﾄ", "Size": "", "ToolOther": "FM-0560", "WorkName": "検査4", "WorkItems": [ "1. [取付完了]を押す", "2. 真空ﾎﾟﾝﾌﾟの電源をONし､[OK]を押す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-0560", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ONしている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部", "Size": "", "ToolOther": "FM-5712", "WorkName": "検査5", "WorkItems": [ "1. ﾍｯﾄﾞの2次元ｺｰﾄﾞをｽｷｬﾝする", "2. ｽｷｬﾝした情報が読み込まれたら､[OK]を押す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "画面確認", "ToolManageNo": "FM-5712", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部", "Size": "", "ToolOther": "FM-5712", "WorkName": "検査6", "WorkItems": [ "1. [検査開始]を押す", "2. ﾁｬｰﾄﾏｰｸの点灯を確認し､[OK]を押す" ], "WorkPoints": [ "検査が自動で開始される", "ﾁｬｰﾄﾏｰｸの点灯確認は､FC16のみ" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "画面確認", "ToolManageNo": "FM-5712", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部", "Size": "", "ToolOther": "FM-5712", "WorkName": "検査7(FC03のみ)", "WorkItems": [ "1. 下記ﾒｯｾｰｼﾞが表示されたら､ｶﾊﾞｰを開け､穴無しﾉｽﾞﾙを取付", "2. ｶﾊﾞｰを閉じ､[取付完了]を押す" ], "WorkPoints": [ "3本取付", "ﾉｽﾞﾙ穴無し" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:ﾍｯﾄﾞﾁｪｯｶｰ確認" ] }
{ "QualityItem": "画面確認", "ToolManageNo": "FM-5712", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "検査7(FC03のみ)", "WorkItems": [ "1. 下記ﾒｯｾｰｼﾞが表示されたら､ｶﾊﾞｰを開け､穴無しﾉｽﾞﾙを取付", "2. ｶﾊﾞｰを閉じ､[取付完了]を押す" ], "WorkPoints": [ "3本取付", "ﾉｽﾞﾙ穴無し" ], "Tolks": [], "InspectionNo": "GWETP-F013-001", "InspectionItems": [ "検査表①:ﾍｯﾄﾞﾁｪｯｶｰ確認" ], "WorkTypes": [], "Words": [ "GWETP-F013-001" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "検査表の通り出来ている事", "Method": "目視", "RecordMethod": "GWETP-F013-001", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部", "Size": "", "ToolOther": "FM-5712", "WorkName": "検査8(FC03のみ)", "WorkItems": [ "1. 下記ﾒｯｾｰｼﾞが表示されたら､ｶﾊﾞｰを開け､穴有りﾉｽﾞﾙを取付", "2. ｶﾊﾞｰを閉じ､[取付完了]を押す" ], "WorkPoints": [ "3本取付", "ﾉｽﾞﾙ穴有り" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:ﾍｯﾄﾞﾁｪｯｶｰ確認" ] }
{ "QualityItem": "画面確認", "ToolManageNo": "FM-5712", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "検査8(FC03のみ)", "WorkItems": [ "1. 下記ﾒｯｾｰｼﾞが表示されたら､ｶﾊﾞｰを開け､穴有りﾉｽﾞﾙを取付", "2. ｶﾊﾞｰを閉じ､[取付完了]を押す" ], "WorkPoints": [ "3本取付", "ﾉｽﾞﾙ穴有り" ], "Tolks": [], "InspectionNo": "GWETP-F013-001", "InspectionItems": [ "検査表①:ﾍｯﾄﾞﾁｪｯｶｰ確認" ], "WorkTypes": [], "Words": [ "GWETP-F013-001" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "検査表の通り出来ている事", "Method": "目視", "RecordMethod": "GWETP-F013-001", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部", "Size": "", "ToolOther": "FM-5712", "WorkName": "検査9(FC03のみ)", "WorkItems": [ "1. 下記ﾒｯｾｰｼﾞが表示されたら､ｶﾊﾞｰを開け､ﾉｽﾞﾙを取外す", "2. 取外したら､ｶﾊﾞｰを閉じ[OK]を押す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "画面確認", "ToolManageNo": "FM-5712", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部", "Size": "", "ToolOther": "FM-5712", "WorkName": "検査終了-①", "WorkItems": [ "1. 検査が終了しOKなら､真空ﾎﾟﾝﾌﾟをOFFし[OK]を押す", "2. [検査ﾓｰﾄﾞ終了]を押す", "3. ｶﾊﾞｰを開け､ﾍｯﾄﾞを取外す" ], "WorkPoints": [ "検査が完了したら､下記ﾒｯｾｰｼﾞが表示されます｡" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:FC16:ﾍｯﾄﾞﾁｪｯｶｰ確認", "検査表②:FC08:ﾍｯﾄﾞﾁｪｯｶｰ確認" ] }
{ "QualityItem": "画面確認", "ToolManageNo": "FM-5712", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "検査終了-①", "WorkItems": [ "1. 検査が終了しOKなら､真空ﾎﾟﾝﾌﾟをOFFし[OK]を押す", "2. [検査ﾓｰﾄﾞ終了]を押す", "3. ｶﾊﾞｰを開け､ﾍｯﾄﾞを取外す" ], "WorkPoints": [ "検査が完了したら､下記ﾒｯｾｰｼﾞが表示されます｡" ], "Tolks": [], "InspectionNo": "GWEHD-F013-001", "InspectionItems": [ "検査表①:FC16:ﾍｯﾄﾞﾁｪｯｶｰ確認" ], "WorkTypes": [], "Words": [ "検査表②:FC08:ﾍｯﾄﾞﾁｪｯｶｰ確認", "GWEHD-F013-001" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "検査表の通り出来ている事", "Method": "目視", "RecordMethod": "GWEHD-F013-001", "Other": "FC16の場合", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "検査終了-①", "WorkItems": [ "1. 検査が終了しOKなら､真空ﾎﾟﾝﾌﾟをOFFし[OK]を押す", "2. [検査ﾓｰﾄﾞ終了]を押す", "3. ｶﾊﾞｰを開け､ﾍｯﾄﾞを取外す" ], "WorkPoints": [ "検査が完了したら､下記ﾒｯｾｰｼﾞが表示されます｡" ], "Tolks": [], "InspectionNo": "GWETJ-F013-001", "InspectionItems": [ "検査表②:FC08:ﾍｯﾄﾞﾁｪｯｶｰ確認" ], "WorkTypes": [], "Words": [ "検査表①:FC16:ﾍｯﾄﾞﾁｪｯｶｰ確認", "GWETJ-F013-001" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "検査表の通り出来ている事", "Method": "目視", "RecordMethod": "GWETJ-F013-001", "Other": "FC08の場合", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "真空ﾎﾟﾝﾌﾟﾕﾆｯﾄ", "Size": "", "ToolOther": "FM-0560", "WorkName": "検査終了-①", "WorkItems": [ "3. ｶﾊﾞｰを開け､ﾍｯﾄﾞを取外す", "3. ｶﾊﾞｰを開け､ﾍｯﾄﾞを取外す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:FC16:ﾍｯﾄﾞﾁｪｯｶｰ確認", "検査表②:FC08:ﾍｯﾄﾞﾁｪｯｶｰ確認", "検査表①:FC16:ﾍｯﾄﾞﾁｪｯｶｰ確認", "検査表②:FC08:ﾍｯﾄﾞﾁｪｯｶｰ確認" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-0560", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "OFFしている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞﾁｪｯｶｰﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部", "Size": "", "ToolOther": "FM-5712", "WorkName": "検査終了-②", "WorkItems": [ "1. 検査が終了しOKなら､真空ﾎﾟﾝﾌﾟをOFFし[OK]を押す", "2. [検査ﾓｰﾄﾞ終了]を押す", "3. ｶﾊﾞｰを開け､ﾍｯﾄﾞを取外す" ], "WorkPoints": [ "検査が完了したら､下記ﾒｯｾｰｼﾞが表示されます｡" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:FC03:32.ﾍｯﾄﾞﾁｪｯｶｰ確認", "FC03ﾍｯﾄﾞ", "FC03ﾍｯﾄﾞ" ] }
{ "QualityItem": "画面確認", "ToolManageNo": "FM-5712", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "検査終了-②", "WorkItems": [ "1. 検査が終了しOKなら､真空ﾎﾟﾝﾌﾟをOFFし[OK]を押す", "2. [検査ﾓｰﾄﾞ終了]を押す", "3. ｶﾊﾞｰを開け､ﾍｯﾄﾞを取外す" ], "WorkPoints": [ "検査が完了したら､下記ﾒｯｾｰｼﾞが表示されます｡" ], "Tolks": [], "InspectionNo": "GWETP-F013-001", "InspectionItems": [ "検査表①:FC03:32.ﾍｯﾄﾞﾁｪｯｶｰ確認" ], "WorkTypes": [], "Words": [ "FC03ﾍｯﾄﾞ", "FC03ﾍｯﾄﾞ", "GWETP-F013-001" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "検査表の通り出来ている事", "Method": "目視", "RecordMethod": "GWETP-F013-001", "Other": "FC03の場合", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "真空ﾎﾟﾝﾌﾟﾕﾆｯﾄ", "Size": "", "ToolOther": "FM-0560", "WorkName": "検査終了-②", "WorkItems": [ "3. ｶﾊﾞｰを開け､ﾍｯﾄﾞを取外す", "3. ｶﾊﾞｰを開け､ﾍｯﾄﾞを取外す" ], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:FC03:32.ﾍｯﾄﾞﾁｪｯｶｰ確認", "検査表①:FC03:32.ﾍｯﾄﾞﾁｪｯｶｰ確認" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-0560", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "OFFしている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "ﾉｽﾞﾙ取付", "WorkItems": [ "1. .ﾍｯﾄﾞにﾉｽﾞﾙを取付" ], "WorkPoints": [ "FC16", "FC08", "FC03はこの作業無し" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "作業指示通り取付け出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞｴｰｼﾞﾝｸﾞ装置親機専用部", "Size": "", "ToolOther": "FM-5686", "WorkName": "ﾍｯﾄﾞ取付", "WorkItems": [ "1. ㉖にヘッドを取付", "2. ｶﾊﾞｰを閉める" ], "WorkPoints": [ "ﾍｯﾄﾞを載せ､背面から4か所のﾈｼﾞ締め", "FC16", "FC08", "FC03" ], "Tolks": [ "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-5686", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付けできている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾚﾝﾁ", "Size": "", "ToolOther": "6.0N･m", "WorkName": "ﾍｯﾄﾞ取付", "WorkItems": [ "1. ㉖にヘッドを取付" ], "WorkPoints": [ "ﾍｯﾄﾞを載せ､背面から4か所のﾈｼﾞ締め", "FC08", "FC03" ], "Tolks": [ "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "6.0N･m±10%", "Method": "ﾄﾙｸﾚﾝﾁ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾍｯﾄﾞ取付けﾛﾝｸﾞﾋﾞｯﾄM5", "Size": "", "ToolOther": "FM-6090", "WorkName": "ﾍｯﾄﾞ取付", "WorkItems": [ "1. ㉖にヘッドを取付" ], "WorkPoints": [ "ﾍｯﾄﾞを載せ､背面から4か所のﾈｼﾞ締め", "FC08", "FC03" ], "Tolks": [ "締付ﾄﾙｸ 6.0N･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "取付確認", "ToolManageNo": "FM-6090", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り取付けできている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞｴｰｼﾞﾝｸﾞ装置親機専用部", "Size": "", "ToolOther": "FM-5686", "WorkName": "ｴｰｼﾞﾝｸﾞ1", "WorkItems": [ "1. ｴｰｼﾞﾝｸﾞｿﾌﾄを起動", "2. 検査員を選択し[OK]を押す", "3. 制御BOXの電源をONする", "4. ｶｳﾝﾀをﾘｾｯﾄする(ｶｳﾝﾀがｾﾞﾛになっていない場合)" ], "WorkPoints": [ "上下ﾎﾞﾀﾝを同時に長押し､ﾘｾｯﾄする" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "画面確認", "ToolManageNo": "FM-5686", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞｴｰｼﾞﾝｸﾞ装置親機専用部", "Size": "", "ToolOther": "FM-5686", "WorkName": "ｴｰｼﾞﾝｸﾞ2", "WorkItems": [ "1. ﾁｪｯｶｿﾌﾄの[開始]を押す", "2. 制御BOXのｽﾀｰﾄを押す", "3. 終了したらﾍｯﾄﾞを外し､ﾉｽﾞﾙを外す" ], "WorkPoints": [ "ｴｰｼﾞﾝｸﾞとｷｬﾘﾌﾞが自動で行われる(FC03はｴｰｼﾞﾝｸﾞのみ)", "FC16､FC08は約6.5時間FC03は約7時間で終了", "FC03はﾉｽﾞﾙ無し" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "画面確認", "ToolManageNo": "FM-5686", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞｴｰｼﾞﾝｸﾞ装置親機専用部", "Size": "", "ToolOther": "FM-5686", "WorkName": "ｴｰｼﾞﾝｸﾞ2", "WorkItems": [ "1. ﾁｪｯｶｿﾌﾄの[開始]を押す", "2. 制御BOXのｽﾀｰﾄを押す", "3. 終了したらﾍｯﾄﾞを外し､ﾉｽﾞﾙを外す" ], "WorkPoints": [ "ｴｰｼﾞﾝｸﾞとｷｬﾘﾌﾞが自動で行われる(FC03はｴｰｼﾞﾝｸﾞのみ)", "FC16､FC08は約6.5時間FC03は約7時間で終了", "FC03はﾉｽﾞﾙ無し" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "GWEHD-F013-001" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-5686", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ｴﾗｰが無いこと", "Method": "目視", "RecordMethod": "GWEHD-F013-001", "Other": "FC16の場合", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞｴｰｼﾞﾝｸﾞ装置親機専用部", "Size": "", "ToolOther": "FM-5686", "WorkName": "ｴｰｼﾞﾝｸﾞ2", "WorkItems": [ "1. ﾁｪｯｶｿﾌﾄの[開始]を押す", "2. 制御BOXのｽﾀｰﾄを押す", "3. 終了したらﾍｯﾄﾞを外し､ﾉｽﾞﾙを外す" ], "WorkPoints": [ "ｴｰｼﾞﾝｸﾞとｷｬﾘﾌﾞが自動で行われる(FC03はｴｰｼﾞﾝｸﾞのみ)", "FC16､FC08は約6.5時間FC03は約7時間で終了", "FC03はﾉｽﾞﾙ無し" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "GWETJ-F013-001" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-5686", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ｴﾗｰが無いこと", "Method": "目視", "RecordMethod": "GWETJ-F013-001", "Other": "FC08の場合", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞｴｰｼﾞﾝｸﾞ装置親機専用部", "Size": "", "ToolOther": "FM-5686", "WorkName": "ｴｰｼﾞﾝｸﾞ3", "WorkItems": [ "1. ﾁｪｯｶｿﾌﾄの[開始]を押す", "2. 制御BOXのｽﾀｰﾄを押す", "3. 終了したらﾍｯﾄﾞを外す" ], "WorkPoints": [ "ｴｰｼﾞﾝｸﾞが自動で行われる(FC03はｴｰｼﾞﾝｸﾞのみ)", "FC03は約7時間で終了", "FC03はﾉｽﾞﾙ無し" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "検査表①:FC03:33.ｴｰｼﾞﾝｸﾞ" ] }
{ "QualityItem": "画面確認", "ToolManageNo": "FM-5686", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "指示通り出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "FCﾍｯﾄﾞｴｰｼﾞﾝｸﾞ装置親機専用部", "Size": "", "ToolOther": "FM-5686", "WorkName": "ｴｰｼﾞﾝｸﾞ3", "WorkItems": [ "1. ﾁｪｯｶｿﾌﾄの[開始]を押す", "2. 制御BOXのｽﾀｰﾄを押す", "3. 終了したらﾍｯﾄﾞを外す" ], "WorkPoints": [ "ｴｰｼﾞﾝｸﾞが自動で行われる(FC03はｴｰｼﾞﾝｸﾞのみ)", "FC03は約7時間で終了", "FC03はﾉｽﾞﾙ無し" ], "Tolks": [], "InspectionNo": "GWETP-F013-001", "InspectionItems": [ "検査表①:FC03:33.ｴｰｼﾞﾝｸﾞ" ], "WorkTypes": [], "Words": [ "GWETP-F013-001" ] }
{ "QualityItem": "動作確認", "ToolManageNo": "FM-5686", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "ｴﾗｰが無いこと", "Method": "目視", "RecordMethod": "GWETP-F013-001", "Other": "FC03の場合", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "Size": "2.5㎜", "ToolOther": "40cN･m", "WorkName": "Y軸ｾﾝｻｰ部組立", "WorkItems": [ "1. BRACKET にSENSOR をBOLT ･WASHER ･WASHER で取付" ], "WorkPoints": [ "L用", "R用" ], "Tolks": [ "締付ﾄﾙｸ 40cN･m" ], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものをL･R用 3組製作" ] }
{ "QualityItem": "締付ﾄﾙｸ", "ToolManageNo": "-", "ToolCycle": "日常点検(1回/日)", "ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳", "StdVal": "40cN･m±10%", "Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "X軸給油部組立", "WorkItems": [ "1. BLOCK にGREASE-NIPPLE を⑯･⑰･⑱で取付" ], "WorkPoints": [ "L用", "R用" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "この作業では同じものをL･R用 3組製作" ] }
{ "QualityItem": "取付確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示通り取付出来ている事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "Y軸用ｹｰﾌﾞﾙﾌﾞﾗｹｯﾄ組立①", "WorkItems": [ "▲1. BRACKET ･BRACKET にSPACER をBOLT ･WASHER で取付しCABLE-SUPPORT を取付" ], "WorkPoints": [ "L用", "R用", "㉖ロックタイト塗布", "㉖ロックタイト塗布" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [ "接着剤塗布 ｺﾞﾏ粒:各2", "この作業では同じものを3組製作", "側面図" ] }
{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布ｺﾞﾏ粒:各2", "Method": "目視", "RecordMethod": "-", "Other": "ﾛｯｸﾀｲﾄ243", "ProcessNames": [ "特殊工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "300㎜", "ToolOther": "", "WorkName": "Y軸用ｹｰﾌﾞﾙﾌﾞﾗｹｯﾄ組立②", "WorkItems": [ "1. BRACKET ･BRACKET にSHEET を貼付", "▲2. 1.完成品にSPACER をBOLT WASHER で取付しCABLE-SUPPORT を取付", "3. 2.完成品に⑥⑦をBOLT WASHER で取付" ], "WorkPoints": [ "L用", "R用", "L用", "R用", "L用", "R用" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [ "この作業では同じものを3組製作", "▲特殊作業" ] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法の位置に貼付けている事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "特殊工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "Y軸用ｹｰﾌﾞﾙﾌﾞﾗｹｯﾄ組立②", "WorkItems": [ "1. BRACKET ･BRACKET にSHEET を貼付", "▲2. 1.完成品にSPACER をBOLT WASHER で取付しCABLE-SUPPORT を取付", "3. 2.完成品に⑥⑦をBOLT WASHER で取付" ], "WorkPoints": [ "L用", "R用", "L用", "R用", "L用", "R用", "㉗ロックタイト塗布", "㉗ロックタイト塗布" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [ "接着剤塗布 ｺﾞﾏ粒:各2", "1.完成品 L", "1.完成品 R", "2.完成品 L", "2.完成品 R", "この作業では同じものを3組製作" ] }
{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布ｺﾞﾏ粒:各2", "Method": "目視", "RecordMethod": "-", "Other": "ﾛｯｸﾀｲﾄ243", "ProcessNames": [ "特殊工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "X軸用ｹｰﾌﾞﾙﾌﾞﾗｹｯﾄ組立", "WorkItems": [ "▲1. BRACKET ･BRACKET にSPACER をBOLT ･WASHER で取付" ], "WorkPoints": [ "L用", "R用", "㉖ロックタイト塗布", "㉖ロックタイト塗布" ], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [ "▲特殊作業", "●クリーン作業" ], "Words": [ "接着剤塗布 ｺﾞﾏ粒:各2", "この作業では同じものを3組製作", "側面図" ] }
{ "QualityItem": "接着量", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "指示箇所に塗布ｺﾞﾏ粒:各2", "Method": "目視", "RecordMethod": "-", "Other": "ﾛｯｸﾀｲﾄ243", "ProcessNames": [ "特殊工程" ] }
information_extraction
0
null
{ "ToolName": "ｽｹｰﾙ", "Size": "600㎜", "ToolOther": "", "WorkName": "銘板貼付け", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "1. COVER COVER にLABEL を貼付", "この作業では同じものを3組製作 (A･P1･P2用)", "L･R用各2枚作成", "貼付け方向注意", "P1･P2のﾗﾍﾞﾙは下記ｷｯﾄから使用の事" ] }
{ "QualityItem": "貼付確認", "ToolManageNo": "-", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "寸法の位置に貼付けている事", "Method": "ｽｹｰﾙ", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "XY軸ﾓｰﾀｰ安全部品検査・原点調整", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-048", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [ "WWYJ-5300-048" ] }
{ "QualityItem": "型式確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式が一致する事", "Method": "目視", "RecordMethod": "WWYJ-5300-048", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "XY軸ﾓｰﾀｰ安全部品検査・原点調整", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-048" ] }
{ "QualityItem": "製造番号記録", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "製造番号転記", "Method": "目視", "RecordMethod": "WWYJ-5300-048", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "原点出し治具", "Size": "", "ToolOther": "FM-3445", "WorkName": "XY軸ﾓｰﾀｰ安全部品検査・原点調整", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "原点確認", "ToolManageNo": "FM-3445", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "原点位置である事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "XY軸ﾓｰﾀｰ安全部品検査・原点調整(P1)", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "WWYJ-5300-048", "InspectionItems": [], "WorkTypes": [ "■安全作業" ], "Words": [ "WWYJ-5300-048" ] }
{ "QualityItem": "型式確認", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "型式が一致する事", "Method": "目視", "RecordMethod": "WWYJ-5300-048", "Other": "-", "ProcessNames": [ "安全工程" ] }
information_extraction
0
null
{ "ToolName": "-", "Size": "", "ToolOther": "", "WorkName": "XY軸ﾓｰﾀｰ安全部品検査・原点調整(P1)", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [ "WWYJ-5300-048" ] }
{ "QualityItem": "製造番号記録", "ToolManageNo": "-", "ToolCycle": "-", "ToolRecord": "-", "StdVal": "製造番号転記", "Method": "目視", "RecordMethod": "WWYJ-5300-048", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null
{ "ToolName": "原点出し治具", "Size": "", "ToolOther": "FM-3445", "WorkName": "XY軸ﾓｰﾀｰ安全部品検査・原点調整(P1)", "WorkItems": [], "WorkPoints": [], "Tolks": [], "InspectionNo": "", "InspectionItems": [], "WorkTypes": [], "Words": [] }
{ "QualityItem": "原点確認", "ToolManageNo": "FM-3445", "ToolCycle": "校正対象外", "ToolRecord": "-", "StdVal": "原点位置である事", "Method": "目視", "RecordMethod": "-", "Other": "-", "ProcessNames": [ "-" ] }
information_extraction
0
null