input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ﾍｯﾄﾞ部_配線②",
"WorkItems": [
"1. ①ﾍｯﾄﾞ先端部の吸着配管を接続する"
],
"WorkPoints": [
"ﾍｯﾄﾞ先端部(MHV軸)を手動でﾌﾙｽﾄﾛｰｸ回して配線配管の干渉が無いことを確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ﾍｯﾄﾞ部_配線③",
"WorkItems": [
"■1. ①ｾﾝｻにCABLE を接続する",
"2. 1完成品の配線配管を引き回しする"
],
"WorkPoints": [
"仮引き回し:SD-A044667-065にて束線､接続"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-111",
"InspectionItems": [
"検査表①:.接続確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"Φ4 黒",
"B10900R",
"ｲﾝｼｭﾛｯｸ(100mm)",
"B10901R",
"B10902R",
"B10903R",
"MH軸ﾛｯｸ用ｼﾘﾝﾀﾞ(1B10930-8R)",
"WWYJ-5300-111"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-111",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ﾊﾟﾈﾙ押さえ/ｲｵﾅｲｻﾞｰ_組込み",
"WorkItems": [
"1. ①に⑪を㉓BOLT で取付け、⑥をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ﾊﾟﾈﾙ押さえ/ｲｵﾅｲｻﾞｰ_配線",
"WorkItems": [
"1. の1完成品の配線配管を引き回し接続する"
],
"WorkPoints": [
"H-BOX",
"①空圧部ﾌﾞﾗｹｯﾄの開口部を通して後部へ引き回し",
"仮引き回し:SD-A044467-064にて束線"
],
"Tolks": [],
"InspectionNo": "WWXJ-5300-086",
"InspectionItems": [
"検査表①:.接続確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"矢視A",
"矢視A",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"E20081E2008RΦ6 黄",
"仮引き回し:SD-A029115-064にて束線",
"ｲﾝｼｭﾛｯｸ(100mm)",
"WWXJ-5300-086"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWXJ-5300-086",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_廃棄BOX部_配線",
"WorkItems": [
"1. ①廃棄BOK部の配線配管を引き回しする"
],
"WorkPoints": [
"空圧部の配管を廃棄BOKｼﾘﾝﾀﾞへ引き回し",
"仮引き回し:SD-A044467-065にて束線､接続",
"廃棄BOKｼﾘﾝﾀﾞ配線を上部へ引き回し"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"1B10930-6R1B10930-7R",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"φ4 黒",
"φ4 黒"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ﾍｯﾄﾞﾍﾞｰｽ空圧部_配線",
"WorkItems": [
"1. ①ﾍｯﾄﾞﾍﾞｰｽ空圧部の配線を引き回し接続する"
],
"WorkPoints": [
"仮引き回し:SD-A044467-065にて束線､接続"
],
"Tolks": [],
"InspectionNo": "WWYJ-5300-111",
"InspectionItems": [
"検査表①:接続確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"矢視A",
"矢視A",
"R30930R",
"R30931R",
"R301R",
"R30932R",
"ｲﾝｼｭﾛｯｸ(100mm)",
"WWYJ-5300-111"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-111",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ｸﾘｰﾝｹｰﾌﾞﾙﾍｯﾄﾞﾍﾞｰｽ側_配線",
"WorkItems": [
"1. ①ﾍｯﾄﾞﾍﾞｰｽ側の配線配管を引き回しする"
],
"WorkPoints": [
"①ﾍｯﾄﾞ側ﾌﾞﾗｹｯﾄ裏図",
"仮引き回し:SD-A044467-065にて束線､接続"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"Φ4 白",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"矢視A",
"Φ4 黒",
"矢視A",
"仮引き回し:SD-A029115-065にて束線､接続",
"ｲﾝｼｭﾛｯｸ(150mm)",
"1B10930-1R1B10930-2R1B10930-3R",
"1B41203P",
"1B10930-4R",
"1E11203P",
"1MHVMM4106R",
"1MHVEM4106R"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "3㎜",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ﾍｯﾄﾞﾍﾞｰｽ部_配管",
"WorkItems": [
"2. ①に1完成品を接続し引き回しする",
"3. 2完成品をｲﾝｼｭﾛｯｸで結束する",
"1. ⑥⑦⑧を下記の寸法にｶｯﾄする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"φ6 黒",
"φ6 白",
"φ6 橙",
"A:1500㎜ 1本C: 360㎜ 1本E:1300㎜ 1本F: 230㎜ 1本G:1500㎜ 1本",
"D:1600㎜ 1本",
"B:1600㎜ 1本"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ﾍｯﾄﾞﾍﾞｰｽ部_配管",
"WorkItems": [
"2. ①に1完成品を接続し引き回しする",
"3. 2完成品をｲﾝｼｭﾛｯｸで結束する",
"1. ⑥⑦⑧を下記の寸法にｶｯﾄする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"φ6 黒",
"φ6 白",
"φ6 橙",
"A:1500㎜ 1本C: 360㎜ 1本E:1300㎜ 1本F: 230㎜ 1本G:1500㎜ 1本",
"D:1600㎜ 1本",
"B:1600㎜ 1本",
"画像変更必要",
"ｲｵﾅｲｻﾞｰ配管",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ﾘﾚｰｷｯﾄ_組込み",
"WorkItems": [
"2. ①にRELAY RELAY-SOCKET をBOLT WASHER WASHER で取付ける",
"■1. RELAY RELAY-SOCKET の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"■3. 2完成品リレーにCABLE CABLE CABLE CABLE を取付け、㉙で結束する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 0.9N･m"
],
"InspectionNo": "WWYJ-5300-111",
"InspectionItems": [
"検査表①:接続確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:型式･ｼﾘｱﾙ･検査書ﾁｪｯｸ",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WWYJ-5300-111"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式が一致する事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-111",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ﾘﾚｰｷｯﾄ_組込み",
"WorkItems": [
"2. ①にRELAY RELAY-SOCKET をBOLT WASHER WASHER で取付ける",
"■1. RELAY RELAY-SOCKET の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"■3. 2完成品リレーにCABLE CABLE CABLE CABLE を取付け、㉙で結束する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 0.9N･m"
],
"InspectionNo": "WWYJ-5300-111",
"InspectionItems": [
"検査表①:型式･ｼﾘｱﾙ･検査書ﾁｪｯｸ"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:接続確認",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WWYJ-5300-111"
]
} | {
"QualityItem": "製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "製造番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-111",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ﾘﾚｰｷｯﾄ_組込み",
"WorkItems": [
"2. ①にRELAY RELAY-SOCKET をBOLT WASHER WASHER で取付ける",
"■1. RELAY RELAY-SOCKET の型式を確認し､ｼﾘｱﾙNoを検査表に記入する",
"■3. 2完成品リレーにCABLE CABLE CABLE CABLE を取付け、㉙で結束する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 0.9N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:接続確認",
"検査表①:型式･ｼﾘｱﾙ･検査書ﾁｪｯｸ",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WWYJ-5300-111"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-111",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "0.9N･m",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ﾘﾚｰｷｯﾄ_組込み",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 0.9N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:接続確認",
"検査表①:型式･ｼﾘｱﾙ･検査書ﾁｪｯｸ",
"ｲﾝｼｭﾛｯｸ(100mm)",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "0.9N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ﾍｯﾄﾞﾍﾞｰｽ部_配線",
"WorkItems": [
"1. ①ｺﾈｸﾀﾌﾞﾗｹｯﾄにCABLE CABLE CABLE CABLE CABLE CABLE CABLE を取付け､引き回し結束する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"1E11203P",
"1B10900R",
"1B41203P",
"MHEM4105R",
"1MHVEM4106R",
"1MHVMM4106R",
"MHMM4105R",
"空圧部ﾊﾞﾙﾌﾞ配線MHBM4105R",
"空圧部ﾊﾞﾙﾌﾞ配線",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "仮圧着ﾍｯﾄﾞﾍﾞｰｽ:M_(逆流れ)_ﾍｯﾄﾞ部、ﾍｯﾄﾞﾍﾞｰｽ部_配線",
"WorkItems": [
"2. ①ﾍｯﾄﾞ部､ﾍｯﾄﾞﾍﾞｰｽ部の配線配管を引き回し接続する",
"1. ①にCABLE を接続する",
"3. BOLT は2完成品に添付し次工程(本体ﾄﾞｯｷﾝｸﾞ)に引渡す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WWYJ-5300-111",
"InspectionItems": [
"検査表①:接続確認",
"検査表①:接続確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"矢視A",
"矢視A:MHV軸ﾓｰﾀｰ",
"矢視A:ｺﾈｸﾀﾌﾞﾗｹｯﾄ",
"MHVMM4106P",
"MHVEM4106P",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WWYJ-5300-111"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WWYJ-5300-111",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立1",
"WorkItems": [
"3. 1完成品を2完成品に取付",
"2. FRAME にCABLE-SUPPORT を取付",
"1. NUT にCAP を取付"
],
"WorkPoints": [
"表面",
"裏面",
"1完成品は表面が上になるように取付",
"ｷｬｯﾌﾟ取付方向に注意する事",
"ｹｰﾌﾞﾙｸﾗﾝﾌﾟを挿入後90度回転させ固定",
"ｹｰﾌﾞﾙｻﾎﾟｰﾄは先に取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M6",
"M6",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立2",
"WorkItems": [
"1. NUT NUT NUT にCAP を取付",
"2. 1完成品を①に取付"
],
"WorkPoints": [
"右側",
"左側",
"右側",
"B\t面",
"表面",
"裏面",
"ｷｬｯﾌﾟ取付方向に注意する事",
"1完成品は表面が上になるように取付",
"ｻｲｽﾞが異なるので注意",
"左側",
"A面",
"ｹｰﾌﾞﾙｻﾎﾟｰﾄ側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M6",
"M4",
"M6",
"M6",
"M6",
"M6",
"M4",
"M6",
"M6",
"M6",
"M6",
"M6",
"M6",
"M4",
"M6",
"M5",
"M6",
"M6",
"M4",
"M4",
"M5",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立3",
"WorkItems": [
"1. NUT にCAP を取付",
"2. 1完成品をFRAME に取付"
],
"WorkPoints": [
"前側",
"後側",
"前側",
"表面",
"裏面",
"ｷｬｯﾌﾟ取付方向に注意する事",
"1完成品は表面が上になるように取付",
"ｻｲｽﾞが異なるので注意",
"後側",
"A面",
"前側",
"後側",
"B面",
"前側",
"後側",
"C面",
"1完成品は表面が上になるように取付",
"前側",
"後側",
"前側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"この作業では同じものを2個製作",
"▲特殊作業"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立3",
"WorkItems": [
"1. NUT にCAP を取付",
"2. 1完成品をFRAME に取付",
"▲3. 2完成品にCAP を取付"
],
"WorkPoints": [
"前側",
"後側",
"前側",
"表面",
"裏面",
"ｷｬｯﾌﾟ取付方向に注意する事",
"1完成品は表面が上になるように取付",
"ｻｲｽﾞが異なるので注意",
"後側",
"A面",
"前側",
"後側",
"B面",
"前側",
"後側",
"C面",
"1完成品は表面が上になるように取付",
"前側",
"後側",
"前側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"M6",
"M6",
"M6",
"M6",
"M6",
"接着剤塗布 小豆:1",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆:1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｽｰﾊﾟｰX",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾌﾚｰﾑ組立4",
"WorkItems": [
"1. ①にBRACKET BRACKET BRACKET をWASHER BOLT BOLT WASHER で取付"
],
"WorkPoints": [
"長穴の長い方が上になるよう取付",
"面に合わせて取付",
"BRACKET 取付詳細",
"ﾌﾚｰﾑｾﾝﾀｰで取付",
"BRACKET 取付詳細",
"面に合わせて取付",
"端面を合わせて取付",
"BRACKET 取付詳細",
"BRACKET 取付詳細",
"BRACKET 取付詳細",
"BRACKET 取付詳細",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"長手方向",
"18㎜側(短手方向)"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"長手方向",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾌﾚｰﾑ組立4",
"WorkItems": [
"1. ①にBRACKET BRACKET BRACKET をWASHER BOLT BOLT WASHER で取付"
],
"WorkPoints": [
"長穴の長い方が上になるよう取付",
"面に合わせて取付",
"BRACKET 取付詳細",
"ﾌﾚｰﾑｾﾝﾀｰで取付",
"BRACKET 取付詳細",
"面に合わせて取付",
"端面を合わせて取付",
"BRACKET 取付詳細",
"BRACKET 取付詳細",
"BRACKET 取付詳細",
"BRACKET 取付詳細",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"長手方向",
"18㎜側(短手方向)"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"長手方向",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "2.2㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立4",
"WorkItems": [
"1. ①にBRACKET BRACKET BRACKET をWASHER BOLT BOLT WASHER で取付"
],
"WorkPoints": [
"長穴の長い方が上になるよう取付",
"面に合わせて取付",
"BRACKET 取付詳細",
"ﾌﾚｰﾑｾﾝﾀｰで取付",
"BRACKET 取付詳細",
"面に合わせて取付",
"端面を合わせて取付",
"BRACKET 取付詳細",
"BRACKET 取付詳細",
"BRACKET 取付詳細",
"BRACKET 取付詳細",
"ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"長手方向",
"18㎜側(短手方向)"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"長手方向",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾌﾚｰﾑ組立5",
"WorkItems": [
"1. ①に②をBRACKET WASHER BOLT で取付"
],
"WorkPoints": [
"SUSﾌﾚｰﾑ間寸法",
"下記図通りに取付",
"取付詳細",
"ﾅｯﾄが下面になるよう取付",
"SUS面を面一に合わせて取付",
"隙間無きよう取付"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"117±1㎜",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑ組立5",
"WorkItems": [
"1. ①に②をBRACKET WASHER BOLT で取付"
],
"WorkPoints": [
"SUSﾌﾚｰﾑ間寸法",
"下記図通りに取付",
"取付詳細",
"ﾅｯﾄが下面になるよう取付",
"SUS面を面一に合わせて取付",
"隙間無きよう取付"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"117±1㎜",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "2.0N･m",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(右側)1",
"WorkItems": [
"1. BRACKET にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"面を合わせる"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(右側)2",
"WorkItems": [
"1. ①にBRACKET をWASHER BOLT で取付"
],
"WorkPoints": [
"矢印方向に押当",
"左右で取付け位置が異なるので注意"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "1.0N･m",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(右側)3",
"WorkItems": [
"1. ①にBRACKET をWASHER BOLT で取付"
],
"WorkPoints": [
"左右で取付け位置が異なることに注意",
"矢印方向に押当"
],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(右側)4",
"WorkItems": [
"1. ①にBRACKET をWASHER BOLT で取付"
],
"WorkPoints": [
"右側組立のみ取付(左側組立は取付なし)",
"矢印方向に押当"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(右側)5",
"WorkItems": [
"1. ①にCOVER を取付"
],
"WorkPoints": [
"右側組立のみ取付(左側組立は取付なし)",
"2㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(右側)6",
"WorkItems": [
"1. ①にCABLE-SUPPORT を取付"
],
"WorkPoints": [
"CABLE-SUPPORT の向き上下"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "2.0N･m",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(左側)1",
"WorkItems": [
"1. BRACKET にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [
"面を合わせる"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "1.0N･m",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(左側)2",
"WorkItems": [
"1. ①にBRACKET をWASHER BOLT で取付"
],
"WorkPoints": [
"左右で取付け位置が異なるので注意",
"矢印方向に押当"
],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "1.0N･m",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(左側)3",
"WorkItems": [
"1. ①にBRACKET をWASHER BOLT で取付"
],
"WorkPoints": [
"左右組立で取付け位置が異なることに注意",
"矢印方向に押当"
],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻｲﾄﾞﾌﾞﾗｹｯﾄ組立(左側)4",
"WorkItems": [
"1. ①にCABLE-SUPPORT を取付"
],
"WorkPoints": [
"左右組立で取付け位置､個数が異なることに注意",
"外面に取付",
"CABLE-SUPPORT の向き上下"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "両面ﾃｰﾌﾟ貼り1",
"WorkItems": [
"1. COVER のアクリルシートをめくり㉖でとめ、脱脂",
"2. 1完成品にTAPE を貼付け圧着",
"1. COVER のアクリルシートをめくり㉖でとめ、脱脂",
"2. 1完成品にTAPE を貼付け圧着"
],
"WorkPoints": [
"Line A",
"片面のみ実施※裏表関係なし",
"脱脂ｴﾘｱ青色点線内(ﾃｰﾌﾟを貼付ける位置)※しっかり脱脂する事",
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"圧着ﾛｰﾗｰで2往復させる",
"FM-5890",
"Line A",
"片面のみ実施※裏表関係なし",
"脱脂ｴﾘｱ青色点線内(ﾃｰﾌﾟを貼付ける位置)※しっかり脱脂する事",
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"圧着ﾛｰﾗｰで2往復させる",
"FM-5890"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"33mm",
"575㎜",
"5mm程度",
"この作業では同じものを2個製作",
"33mm",
"575㎜",
"5mm程度"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "加圧ﾛｰﾗｰｼﾞｸﾞ",
"Size": "5kg",
"ToolOther": "FM-5890",
"WorkName": "両面ﾃｰﾌﾟ貼り1",
"WorkItems": [
"1. COVER のアクリルシートをめくり㉖でとめ、脱脂",
"2. 1完成品にTAPE を貼付け圧着"
],
"WorkPoints": [
"Line A",
"片面のみ実施※裏表関係なし",
"脱脂ｴﾘｱ青色点線内(ﾃｰﾌﾟを貼付ける位置)※しっかり脱脂する事",
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"圧着ﾛｰﾗｰで2往復させる",
"FM-5890"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"33mm",
"575㎜",
"5mm程度"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5890",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "5.5M",
"ToolOther": "",
"WorkName": "両面ﾃｰﾌﾟ貼り1",
"WorkItems": [
"1. COVER のアクリルシートをめくり㉖でとめ、脱脂",
"2. 1完成品にTAPE を貼付け圧着"
],
"WorkPoints": [
"Line A",
"片面のみ実施※裏表関係なし",
"脱脂ｴﾘｱ青色点線内(ﾃｰﾌﾟを貼付ける位置)※しっかり脱脂する事",
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"圧着ﾛｰﾗｰで2往復させる",
"FM-5890"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"33mm",
"575㎜",
"5mm程度"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "両面ﾃｰﾌﾟ貼り2",
"WorkItems": [
"2. 1完成品にTAPE を貼付け圧着",
"1. COVER のアクリルシートをめくり㉖でとめ、脱脂",
"2. 1完成品にTAPE を貼付け圧着",
"1. COVER のアクリルシートをめくり㉖でとめ、脱脂"
],
"WorkPoints": [
"片面のみ実施※裏表関係なし",
"貼付け寸法に注意する事",
"圧着ﾛｰﾗｰで2往復する",
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"★→0.5~1.0㎜程度隙間を開ける",
"◆→1㎜程度隙間を開ける",
"脱脂ｴﾘｱ青色点線内(ﾃｰﾌﾟを貼付ける位置)※しっかり脱脂する事",
"片面のみ実施※裏表関係なし",
"貼付け寸法に注意する事",
"圧着ﾛｰﾗｰで2往復する",
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"★→0.5~1.0㎜程度隙間を開ける",
"◆→1㎜程度隙間を開ける",
"脱脂ｴﾘｱ青色点線内(ﾃｰﾌﾟを貼付ける位置)※しっかり脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"16mm",
"この作業では同じものを2個製作",
"50㎜",
"70㎜",
"50㎜",
"50㎜",
"16mm",
"この作業では同じものを2個製作",
"50㎜",
"70㎜",
"50㎜",
"50㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "加圧ﾛｰﾗｰｼﾞｸﾞ",
"Size": "5kg",
"ToolOther": "FM-5890",
"WorkName": "両面ﾃｰﾌﾟ貼り2",
"WorkItems": [
"2. 1完成品にTAPE を貼付け圧着",
"1. COVER のアクリルシートをめくり㉖でとめ、脱脂"
],
"WorkPoints": [
"片面のみ実施※裏表関係なし",
"貼付け寸法に注意する事",
"圧着ﾛｰﾗｰで2往復する",
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"★→0.5~1.0㎜程度隙間を開ける",
"◆→1㎜程度隙間を開ける",
"脱脂ｴﾘｱ青色点線内(ﾃｰﾌﾟを貼付ける位置)※しっかり脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"16mm",
"この作業では同じものを2個製作",
"50㎜",
"70㎜",
"50㎜",
"50㎜"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5890",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｺﾝﾍﾞｯｸｽ",
"Size": "5.5M",
"ToolOther": "",
"WorkName": "両面ﾃｰﾌﾟ貼り2",
"WorkItems": [
"2. 1完成品にTAPE を貼付け圧着",
"1. COVER のアクリルシートをめくり㉖でとめ、脱脂"
],
"WorkPoints": [
"片面のみ実施※裏表関係なし",
"貼付け寸法に注意する事",
"圧着ﾛｰﾗｰで2往復する",
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"★→0.5~1.0㎜程度隙間を開ける",
"◆→1㎜程度隙間を開ける",
"脱脂ｴﾘｱ青色点線内(ﾃｰﾌﾟを貼付ける位置)※しっかり脱脂する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"16mm",
"この作業では同じものを2個製作",
"50㎜",
"70㎜",
"50㎜",
"50㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±1.0㎜",
"Method": "ｺﾝﾍﾞｯｸｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "両面ﾃｰﾌﾟ貼り3",
"WorkItems": [],
"WorkPoints": [
"圧着ﾛｰﾗｰで2往復する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"P642"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "加圧ﾛｰﾗｰｼﾞｸﾞ",
"Size": "5kg",
"ToolOther": "FM-5890",
"WorkName": "両面ﾃｰﾌﾟ貼り3",
"WorkItems": [],
"WorkPoints": [
"圧着ﾛｰﾗｰで2往復する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"P642"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5890",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃｰﾌﾟ位置決めｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6568",
"WorkName": "両面ﾃｰﾌﾟ貼り3",
"WorkItems": [
"1. COVER を㉚にセット。A,Bで固定し脱脂する"
],
"WorkPoints": [
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"圧着ﾛｰﾗｰで2往復する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"貼付け面",
"6mm",
"394mm",
"6mm",
"413mm",
"140mm",
"394mm",
"6mm",
"P642"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6568",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "両面ﾃｰﾌﾟ貼り4",
"WorkItems": [
"3. COVER を脱脂しCの右端からBの左端の間にTAPE を貼付ける",
"4. COVER を付替えて(反転)脱脂しCの右端からCOVER の左端の間TAPE を貼付ける",
"5. 治具からCOVER とAを取外し､貼付けたﾃｰﾌﾟを圧着する"
],
"WorkPoints": [
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"圧着ﾛｰﾗｰで2往復する",
"貼付け面",
"Aに沿うように貼る"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "加圧ﾛｰﾗｰｼﾞｸﾞ",
"Size": "5kg",
"ToolOther": "FM-5890",
"WorkName": "両面ﾃｰﾌﾟ貼り4",
"WorkItems": [
"3. COVER を脱脂しCの右端からBの左端の間にTAPE を貼付ける",
"4. COVER を付替えて(反転)脱脂しCの右端からCOVER の左端の間TAPE を貼付ける",
"5. 治具からCOVER とAを取外し､貼付けたﾃｰﾌﾟを圧着する"
],
"WorkPoints": [
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"圧着ﾛｰﾗｰで2往復する",
"貼付け面",
"Aに沿うように貼る"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5890",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃｰﾌﾟ位置決めｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6568",
"WorkName": "両面ﾃｰﾌﾟ貼り4",
"WorkItems": [
"2. ㉚のD、E、F間にTAPE をセットしGで固定する",
"2. ㉚のD、E、F間にTAPE をセットしGで固定する",
"3. COVER を脱脂しCの右端からBの左端の間にTAPE を貼付ける",
"4. COVER を付替えて(反転)脱脂しCの右端からCOVER の左端の間TAPE を貼付ける",
"5. 治具からCOVER とAを取外し､貼付けたﾃｰﾌﾟを圧着する",
"3. COVER を脱脂しCの右端からBの左端の間にTAPE を貼付ける",
"4. COVER を付替えて(反転)脱脂しCの右端からCOVER の左端の間TAPE を貼付ける",
"5. 治具からCOVER とAを取外し､貼付けたﾃｰﾌﾟを圧着する"
],
"WorkPoints": [
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"圧着ﾛｰﾗｰで2往復する",
"貼付け面",
"Aに沿うように貼る",
"圧着方法:両面ﾃｰﾌﾟの上からﾛｰﾗで押さえながら転がす",
"圧着ﾛｰﾗｰで2往復する",
"貼付け面",
"Aに沿うように貼る"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6568",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "両面ﾃｰﾌﾟ貼り5",
"WorkItems": [],
"WorkPoints": [
"Eをｽﾗｲﾄﾞさせながら沿わす様に貼付ける",
"圧着ﾛｰﾗｰで2往復",
"Eの左端がGの右端位置の時､TAPE をFの左端位置でｶｯﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"4mm",
"この作業では同じものを4個製作",
"4mm",
"上端面より",
"この作業では同じものを2個製作",
"P643"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "加圧ﾛｰﾗｰｼﾞｸﾞ",
"Size": "5kg",
"ToolOther": "FM-5890",
"WorkName": "両面ﾃｰﾌﾟ貼り5",
"WorkItems": [],
"WorkPoints": [
"圧着ﾛｰﾗｰで2往復",
"Eの左端がGの右端位置の時､TAPE をFの左端位置でｶｯﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"P643"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5890",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃｰﾌﾟ位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6568",
"WorkName": "両面ﾃｰﾌﾟ貼り5",
"WorkItems": [],
"WorkPoints": [
"Eをｽﾗｲﾄﾞさせながら沿わす様に貼付ける",
"Eをｽﾗｲﾄﾞさせながら沿わす様に貼付ける",
"圧着ﾛｰﾗｰで2往復",
"Eの左端がGの右端位置の時､TAPE をFの左端位置でｶｯﾄ",
"圧着ﾛｰﾗｰで2往復",
"Eの左端がGの右端位置の時､TAPE をFの左端位置でｶｯﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"4mm",
"この作業では同じものを4個製作",
"4mm",
"上端面より",
"4mm",
"この作業では同じものを4個製作",
"4mm",
"上端面より",
"この作業では同じものを2個製作",
"P643",
"この作業では同じものを2個製作",
"P643"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6568",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "両面ﾃｰﾌﾟ貼り6",
"WorkItems": [
"1. COVER をA,B,C,で固定し脱脂する",
"2. FをEの右の穴を基準にｾｯﾄしTAPE を貼付ける",
"5. 完成品のTAPE を圧着する"
],
"WorkPoints": [
"圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす(2往復すること)",
"Eをｽﾗｲﾄﾞさせながら沿わす様に貼付ける",
"SD-A050931-024で使用する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"4.5㎜",
"COVER ",
"COVER ",
"P639"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "加圧ﾛｰﾗｰｼﾞｸﾞ",
"Size": "5kg",
"ToolOther": "FM-5890",
"WorkName": "両面ﾃｰﾌﾟ貼り6",
"WorkItems": [
"5. 完成品のTAPE を圧着する"
],
"WorkPoints": [
"圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす(2往復すること)",
"Eをｽﾗｲﾄﾞさせながら沿わす様に貼付ける",
"SD-A050931-024で使用する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"P639"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5890",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾃｰﾌﾟ位置決めｼﾞｸﾞ(NPM-GH)",
"Size": "",
"ToolOther": "FM-6345",
"WorkName": "両面ﾃｰﾌﾟ貼り6",
"WorkItems": [
"1. COVER をA,B,C,で固定し脱脂する",
"2. FをEの右の穴を基準にｾｯﾄしTAPE を貼付ける",
"1. COVER をA,B,C,で固定し脱脂する",
"2. FをEの右の穴を基準にｾｯﾄしTAPE を貼付ける",
"3. COVER をA,B,C,で固定し脱脂する",
"4. FをEの右の穴を基準にｾｯﾄしTAPE を貼付ける",
"5. 完成品のTAPE を圧着する"
],
"WorkPoints": [
"圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす(2往復すること)",
"Eをｽﾗｲﾄﾞさせながら沿わす様に貼付ける",
"SD-A050931-024で使用する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"4.5㎜",
"COVER ",
"COVER ",
"4.5㎜",
"COVER ",
"COVER ",
"15㎜",
"P639"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6345",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立1",
"WorkItems": [
"1. FRAME にBRACKET をBOLT WASHER で仮締め",
"2. FRAME にBUSH BUSH を取付",
"3. 2完成品にCABLE を挿入"
],
"WorkPoints": [
"矢印の方向から挿入",
"FRONT側:REAR側共通S311/312R1-S311/312R",
"BRACKET の向きに注意して取付",
"BRACKET はｸﾞﾗｸﾞﾗで仮止め",
"S311/312R側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"仮止め:SD-A050931-030にて本締め",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "開閉ｶﾊﾞｰ組立ｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6552",
"WorkName": "開閉ｶﾊﾞｰ組立2",
"WorkItems": [
"1. ㉖に①をセットし、治具番号7，8を取付",
"3. ﾌﾚｰﾑを脱脂し治具番号1を取付ける"
],
"WorkPoints": [
"この作業では同じものを2個製作",
"治具番号1"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-6552",
"ﾌﾚｰﾑ位置にｽﾞﾚ無きこと",
"治具番号 7",
"治具番号 8",
"矢印方向に押し当て｡貼付け後､手で仮圧着"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6552",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立2",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "開閉ｶﾊﾞｰ組立ｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6552",
"WorkName": "開閉ｶﾊﾞｰ組立3",
"WorkItems": [
"1. ㉖に治具番号9,10をセットする",
"2. ①に②を取付",
"3. 治具番号9･10を取り外す"
],
"WorkPoints": [
"穴位置を合わせた後､貼付けし､手で仮圧着"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"治具番号 10",
"治具番号 9",
"側面",
"側面"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6552",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "開閉ｶﾊﾞｰ組立4",
"WorkItems": [
"1. ①にPULL をBOLT WASHER WASHER で取付"
],
"WorkPoints": [
"BOLT 締結後蓋を閉じる"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "開閉ｶﾊﾞｰ組立ｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6552",
"WorkName": "開閉ｶﾊﾞｰ組立5",
"WorkItems": [
"3. 2完成品に②③を貼付",
"1. ①に専用治具を取付ける",
"2. SPRING-PLATE を取付(挟み込む)",
"3. 2完成品に②③を貼付",
"1. ①に専用治具を取付ける",
"2. SPRING-PLATE を取付(挟み込む)"
],
"WorkPoints": [
"FM-6552",
"FM-6552",
"FM-6552",
"治具番号③",
"治具番号②",
"FM-6552",
"FM-6552",
"FM-6552",
"治具番号③",
"治具番号②"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6552",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "1.2㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立5",
"WorkItems": [
"3. 2完成品に②③を貼付",
"1. ①に専用治具を取付ける",
"2. SPRING-PLATE を取付(挟み込む)",
"3. 2完成品に②③を貼付",
"1. ①に専用治具を取付ける",
"2. SPRING-PLATE を取付(挟み込む)"
],
"WorkPoints": [
"FM-6552",
"FM-6552",
"FM-6552",
"治具番号③",
"治具番号②",
"FM-6552",
"FM-6552",
"FM-6552",
"治具番号③",
"治具番号②"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "開閉ｶﾊﾞｰ組立ｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6552",
"WorkName": "開閉ｶﾊﾞｰ組立6",
"WorkItems": [
"1. Bを取外し治具台を定位置に戻しCを取外しﾌﾚｰﾑを脱脂する",
"2. 専用治具を取付ける"
],
"WorkPoints": [
"方向注意の事",
"FM-6552",
"FM-6552",
"FM-6552"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"33mm",
"治具番号4",
"治具番号5",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6552",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立6",
"WorkItems": [],
"WorkPoints": [
"方向注意の事",
"FM-6552",
"FM-6552",
"FM-6552"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"33mm",
"治具番号4",
"治具番号5",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "開閉ｶﾊﾞｰ組立ｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6552",
"WorkName": "開閉ｶﾊﾞｰ組立7",
"WorkItems": [],
"WorkPoints": [
"隙間が無い事",
"端面が合っている事",
"FM-6552",
"FM-6552",
"FM-6552",
"圧着ﾛｰﾗｰで2往復",
"配線側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"治具番号3",
"治具番号2"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6552",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "加圧ﾛｰﾗｰｼﾞｸﾞ",
"Size": "5kg",
"ToolOther": "FM-5890",
"WorkName": "開閉ｶﾊﾞｰ組立7",
"WorkItems": [],
"WorkPoints": [
"隙間が無い事",
"端面が合っている事",
"FM-6552",
"FM-6552",
"FM-6552",
"圧着ﾛｰﾗｰで2往復",
"配線側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"治具番号3",
"治具番号2"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5890",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "開閉ｶﾊﾞｰ組立ｼﾞｸﾞ(NPM-GW)",
"Size": "",
"ToolOther": "FM-6552",
"WorkName": "開閉ｶﾊﾞｰ組立8",
"WorkItems": [
"6. 内側の紙ﾃｰﾌﾟでとめたｱｸﾘﾙｼｰﾄをもとに戻す",
"5. ①に②③を貼付け圧着",
"4. 治具番号2･3を取付ける",
"3. SPRING-PLATE を取付(挟み込む)",
"2. ①のｱｸﾘﾙｼｰﾄをめくり紙ﾃｰﾌﾟでとめ､脱脂",
"1.治具台を定位置に戻す"
],
"WorkPoints": [
"圧着方法:貼付け部材の上からﾛｰﾗで押さえながら転がす",
"FM-6552",
"②を貼り終えてから③を貼る",
"圧着ﾛｰﾗｰで2往復する",
"ｱｸﾘﾙに挟む"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"治具番号6",
"治具番号3",
"治具番号2",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6552",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "加圧ﾛｰﾗｰｼﾞｸﾞ",
"Size": "5kg",
"ToolOther": "FM-5890",
"WorkName": "開閉ｶﾊﾞｰ組立8",
"WorkItems": [
"6. 内側の紙ﾃｰﾌﾟでとめたｱｸﾘﾙｼｰﾄをもとに戻す",
"5. ①に②③を貼付け圧着",
"4. 治具番号2･3を取付ける",
"3. SPRING-PLATE を取付(挟み込む)",
"2. ①のｱｸﾘﾙｼｰﾄをめくり紙ﾃｰﾌﾟでとめ､脱脂",
"1.治具台を定位置に戻す"
],
"WorkPoints": [
"②を貼り終えてから③を貼る",
"圧着ﾛｰﾗｰで2往復する",
"ｱｸﾘﾙに挟む"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5890",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立8",
"WorkItems": [
"6. 内側の紙ﾃｰﾌﾟでとめたｱｸﾘﾙｼｰﾄをもとに戻す",
"5. ①に②③を貼付け圧着",
"4. 治具番号2･3を取付ける",
"3. SPRING-PLATE を取付(挟み込む)",
"2. ①のｱｸﾘﾙｼｰﾄをめくり紙ﾃｰﾌﾟでとめ､脱脂",
"1.治具台を定位置に戻す"
],
"WorkPoints": [
"②を貼り終えてから③を貼る",
"圧着ﾛｰﾗｰで2往復する",
"ｱｸﾘﾙに挟む"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "3.2N･m",
"WorkName": "開閉ｶﾊﾞｰ組立9",
"WorkItems": [
"1. ①のAを本締めする"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立9(左ｶﾞｽﾀﾞﾝﾊﾟｰ)",
"WorkItems": [
"■1. GAS-SPRING の型式を確認し､製造ﾛｯﾄNo.を検査書に記入",
"◆2. GAS-SPRING BOLT BOLT WASHER WASHER ､付属波ﾜｯｼｬｰ､ﾌｪﾉｰﾙﾜｯｼｬｰにｸﾞﾘｰｽを塗布",
"3. COVER にBUSH を取付",
"■4. GAS-SPRING にBRACKET BOLT BOLT WASHER BRACKET WASHER NUT ､3完成品を取付"
],
"WorkPoints": [
"付属波ﾜｯｼｬｰ",
"付属ﾌｪﾉｰﾙﾜｯｼｬｰ",
"付属波ﾜｯｼｬｰ",
"付属ﾌｪﾉｰﾙﾜｯｼｬｰ",
"取付方向に注意する事",
"取付方向に注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m"
],
"InspectionNo": "WETE-G002-C14",
"InspectionItems": [
"検査表GAS-SPRING :1.ｶﾞｽｽﾌﾟﾘﾝｸﾞの締付ﾄﾙｸ"
],
"WorkTypes": [
"■安全作業",
"◆作業者安全作業"
],
"Words": [
"ﾜｯｼｬ接触部両ｻｲﾄﾞ両面ｸﾞﾘｰｽ塗布 小豆:各1",
"この作業では同じものを2個製作",
"3か所",
"ｸﾞﾘｰｽ塗布 小豆:1",
"検査表GAS-SPRING :6.型式確認と製造ﾛｯﾄNo.確認",
"WETE-G002-C14"
]
} | {
"QualityItem": "型式･ﾛｯﾄ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ﾛｯﾄ番号転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C14",
"Other": "-",
"ProcessNames": [
"安全工程",
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立9(左ｶﾞｽﾀﾞﾝﾊﾟｰ)",
"WorkItems": [
"■1. GAS-SPRING の型式を確認し､製造ﾛｯﾄNo.を検査書に記入",
"◆2. GAS-SPRING BOLT BOLT WASHER WASHER ､付属波ﾜｯｼｬｰ､ﾌｪﾉｰﾙﾜｯｼｬｰにｸﾞﾘｰｽを塗布",
"3. COVER にBUSH を取付",
"■4. GAS-SPRING にBRACKET BOLT BOLT WASHER BRACKET WASHER NUT ､3完成品を取付"
],
"WorkPoints": [
"付属波ﾜｯｼｬｰ",
"付属ﾌｪﾉｰﾙﾜｯｼｬｰ",
"付属波ﾜｯｼｬｰ",
"付属ﾌｪﾉｰﾙﾜｯｼｬｰ",
"取付方向に注意する事",
"取付方向に注意する事"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"◆作業者安全作業"
],
"Words": [
"ﾜｯｼｬ接触部両ｻｲﾄﾞ両面ｸﾞﾘｰｽ塗布 小豆:各1",
"この作業では同じものを2個製作",
"3か所",
"検査表GAS-SPRING :1.ｶﾞｽｽﾌﾟﾘﾝｸﾞの締付ﾄﾙｸ",
"ｸﾞﾘｰｽ塗布 小豆:1",
"検査表GAS-SPRING :6.型式確認と製造ﾛｯﾄNo.確認"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"安全工程",
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20N･m",
"WorkName": "開閉ｶﾊﾞｰ組立9(左ｶﾞｽﾀﾞﾝﾊﾟｰ)",
"WorkItems": [
"■1. GAS-SPRING の型式を確認し､製造ﾛｯﾄNo.を検査書に記入",
"◆2. GAS-SPRING BOLT BOLT WASHER WASHER ､付属波ﾜｯｼｬｰ､ﾌｪﾉｰﾙﾜｯｼｬｰにｸﾞﾘｰｽを塗布",
"3. COVER にBUSH を取付"
],
"WorkPoints": [
"付属波ﾜｯｼｬｰ"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m"
],
"InspectionNo": "WETE-G002-C14",
"InspectionItems": [
"検査表GAS-SPRING :6.型式確認と製造ﾛｯﾄNo.確認"
],
"WorkTypes": [
"■安全作業",
"◆作業者安全作業"
],
"Words": [
"ﾜｯｼｬ接触部両ｻｲﾄﾞ両面ｸﾞﾘｰｽ塗布 小豆:各1",
"この作業では同じものを2個製作",
"3か所",
"検査表GAS-SPRING :1.ｶﾞｽｽﾌﾟﾘﾝｸﾞの締付ﾄﾙｸ",
"ｸﾞﾘｰｽ塗布 小豆:1",
"■安全作業",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立10(右ｶﾞｽﾀﾞﾝﾊﾟｰ)",
"WorkItems": [
"■1. GAS-SPRING の型式を確認し､製造ﾛｯﾄNo.を検査書に記入",
"◆2. GAS-SPRING BOLT BOLT WASHER WASHER ､付属波ﾜｯｼｬｰ､ﾌｪﾉｰﾙﾜｯｼｬｰにｸﾞﾘｰｽを塗布",
"3. COVER にBUSH を取付",
"■4. GAS-SPRING にBRACKET BOLT BOLT WASHER BRACKET WASHER NUT ､3完成品を取付"
],
"WorkPoints": [
"取付け方向に注意する事",
"取付け方向に注意する事",
"付属波ﾜｯｼｬｰ",
"付属ﾌｪﾉｰﾙﾜｯｼｬｰ",
"付属ﾌｪﾉｰﾙﾜｯｼｬｰ",
"付属波ﾜｯｼｬｰ",
"長い方",
"短い方"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m",
"締付ﾄﾙｸ 20N･m"
],
"InspectionNo": "WETE-G002-C14",
"InspectionItems": [
"検査表GAS-SPRING :6.型式確認と製造ﾛｯﾄNo.確認"
],
"WorkTypes": [
"■安全作業",
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:1",
"ﾜｯｼｬ接触部両ｻｲﾄﾞ両面ｸﾞﾘｰｽ塗布 小豆:各1",
"この作業では同じものを2個製作",
"検査表GAS-SPRING :1.ｶﾞｽｽﾌﾟﾘﾝｸﾞの締付ﾄﾙｸ",
"WETE-G002-C14"
]
} | {
"QualityItem": "型式･ﾛｯﾄ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ﾛｯﾄ番号転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C14",
"Other": "-",
"ProcessNames": [
"安全工程",
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立10(右ｶﾞｽﾀﾞﾝﾊﾟｰ)",
"WorkItems": [
"■1. GAS-SPRING の型式を確認し､製造ﾛｯﾄNo.を検査書に記入",
"◆2. GAS-SPRING BOLT BOLT WASHER WASHER ､付属波ﾜｯｼｬｰ､ﾌｪﾉｰﾙﾜｯｼｬｰにｸﾞﾘｰｽを塗布",
"3. COVER にBUSH を取付",
"■4. GAS-SPRING にBRACKET BOLT BOLT WASHER BRACKET WASHER NUT ､3完成品を取付"
],
"WorkPoints": [
"取付け方向に注意する事",
"取付け方向に注意する事",
"付属波ﾜｯｼｬｰ",
"付属ﾌｪﾉｰﾙﾜｯｼｬｰ",
"付属ﾌｪﾉｰﾙﾜｯｼｬｰ",
"付属波ﾜｯｼｬｰ",
"長い方",
"短い方"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m",
"締付ﾄﾙｸ 20N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:1",
"ﾜｯｼｬ接触部両ｻｲﾄﾞ両面ｸﾞﾘｰｽ塗布 小豆:各1",
"この作業では同じものを2個製作",
"検査表GAS-SPRING :6.型式確認と製造ﾛｯﾄNo.確認",
"検査表GAS-SPRING :1.ｶﾞｽｽﾌﾟﾘﾝｸﾞの締付ﾄﾙｸ"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "小豆:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"安全工程",
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "20N･m",
"WorkName": "開閉ｶﾊﾞｰ組立10(右ｶﾞｽﾀﾞﾝﾊﾟｰ)",
"WorkItems": [
"3. COVER にBUSH を取付"
],
"WorkPoints": [
"取付け方向に注意する事",
"付属波ﾜｯｼｬｰ",
"付属ﾌｪﾉｰﾙﾜｯｼｬｰ",
"付属波ﾜｯｼｬｰ",
"長い方",
"短い方"
],
"Tolks": [
"締付ﾄﾙｸ 20N･m",
"締付ﾄﾙｸ 20N･m"
],
"InspectionNo": "WETE-G002-C14",
"InspectionItems": [
"検査表GAS-SPRING :1.ｶﾞｽｽﾌﾟﾘﾝｸﾞの締付ﾄﾙｸ"
],
"WorkTypes": [
"■安全作業",
"◆作業者安全作業"
],
"Words": [
"ﾜｯｼｬ接触部両ｻｲﾄﾞ両面ｸﾞﾘｰｽ塗布 小豆:各1",
"検査表GAS-SPRING :6.型式確認と製造ﾛｯﾄNo.確認",
"■安全作業",
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程",
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立11(ﾋﾝｼﾞ組立)",
"WorkItems": [
"2. HINGE を再度組立",
"◆1. HINGE の青枠線内にｸﾞﾘｰｽを塗布"
],
"WorkPoints": [
"外したEﾘﾝｸﾞで固定",
"Eﾘﾝｸﾞの面取り側を内側にする",
"ﾋﾟﾝ",
"組み合わせ方向･ﾋﾟﾝ挿入方向に注意<下図参照>"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"取付け方向に注意!この部品には方向性があります",
"ｸﾞﾘｰｽ塗布 米粒:各1",
"この作業では同じものを4個製作"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "100cN･m",
"WorkName": "開閉ｶﾊﾞｰ組立12(安全SW組立)",
"WorkItems": [
"1. BRACKET にSWITCH をBOLT NUT で取付"
],
"WorkPoints": [
"ﾅｯﾄ側も同等のﾄﾙｸで締付けの事",
"BRACKET ﾌｨｰﾀﾞﾃｰﾌﾞﾙｶﾊﾞｰSWSWITCH 開閉ｶﾊﾞｰSWの､ﾛｯﾄNOを(F側･R側)合わせる事"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"取付け方向に注意!この部品には方向性があります",
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(全体ｶﾊﾞｰ)",
"Size": "",
"ToolOther": "FM-6617",
"WorkName": "開閉ｶﾊﾞｰ組立12(安全SW組立)",
"WorkItems": [
"3. 2完成品を脱脂後､LABEL を貼付"
],
"WorkPoints": [
"裏面",
"開閉カバーSWのＦ側・R側で銘板を㉙使用し貼付け",
"型式表示が上を向くように",
"ﾌｨｰﾀﾞｶﾊﾞｰ用SW組立で未使用の開閉ｶﾊﾞｰ用SWを使用",
"㉙をセットする"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6617",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立13",
"WorkItems": [
"1. ①のｺﾈｸﾀとCABLE のｺﾈｸﾀを接続し､配線をｲﾝｼｭﾛｯｸで固定する",
"2. ②を1完成品にBOLT WASHER で固定"
],
"WorkPoints": [
"治具をｶﾊﾞｰにあてつける",
"治具の挿入隙間を確保する事",
"F側とR側を区別する事",
"SWﾌﾞﾗｹｯﾄを上下させて調整"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "WETE-G002-C14",
"InspectionItems": [
"検査表①:ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"この作業では同じものを2個製作",
"被覆部で固定する事",
"WETE-G002-C14"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C14",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "T20",
"ToolOther": "194cN･m",
"WorkName": "開閉ｶﾊﾞｰ組立13",
"WorkItems": [
"1. ①のｺﾈｸﾀとCABLE のｺﾈｸﾀを接続し､配線をｲﾝｼｭﾛｯｸで固定する",
"2. ②を1完成品にBOLT WASHER で固定"
],
"WorkPoints": [
"治具をｶﾊﾞｰにあてつける",
"SWﾌﾞﾗｹｯﾄを上下させて調整"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"検査表①:ｺﾈｸﾀ接続確認",
"被覆部で固定する事"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "開閉ｶﾊﾞｰ安全SW調整治具(Gｼﾘｰｽﾞ)",
"Size": "",
"ToolOther": "FM-6034",
"WorkName": "開閉ｶﾊﾞｰ組立13",
"WorkItems": [
"1. ①のｺﾈｸﾀとCABLE のｺﾈｸﾀを接続し､配線をｲﾝｼｭﾛｯｸで固定する",
"2. ②を1完成品にBOLT WASHER で固定"
],
"WorkPoints": [
"治具をｶﾊﾞｰにあてつける",
"SWﾌﾞﾗｹｯﾄを上下させて調整"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作",
"検査表①:ｺﾈｸﾀ接続確認",
"被覆部で固定する事"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6034",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立14",
"WorkItems": [
"1. ①の配線をｲﾝｼｭﾛｯｸで固定",
"3 2完成品にRUBBER-CUSHION を取付",
"2. 1完成品に黄色ﾏｰｷﾝｸﾞ"
],
"WorkPoints": [
"ｲﾝｼｭﾛｯｸと配線の位置関係"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"70mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "6㎜",
"ToolOther": "9.8N･m",
"WorkName": "開閉ｶﾊﾞｰ組立15",
"WorkItems": [
"1. ①に②PLATE をBOLT WASHER で取付",
"2. 1完成品にMAGNET をSCREW で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 90cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "90cN･m",
"WorkName": "開閉ｶﾊﾞｰ組立15",
"WorkItems": [],
"WorkPoints": [
"面位置に合わす"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.8㎜"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "90cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "1.8㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立15",
"WorkItems": [
"1. ①に②PLATE をBOLT WASHER で取付",
"2. 1完成品にMAGNET をSCREW で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 90cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(全体ｶﾊﾞｰ)",
"Size": "",
"ToolOther": "FM-6617",
"WorkName": "開閉ｶﾊﾞｰﾗﾍﾞﾙ貼付け",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6617",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "開閉ｶﾊﾞｰ組立16(ﾀﾞﾝﾊﾟｰ取付け)",
"WorkItems": [
"1. ②③にｸｯｼｮﾝ材を巻く",
"2. ①に1完成品をWASHER BOLT で取付"
],
"WorkPoints": [
"矢印方向に押し当てて取付",
"取付場所2か所あり",
"このﾀｯﾌﾟは使用しない",
"このﾀｯﾌﾟは使用しない",
"ﾎﾞﾙﾄ頭が内側へ向くこと",
"ﾎﾞﾙﾄ頭が内側へ向くこと",
"この作業では同じものを2個製作",
"取付目安 1.0㎜"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "開閉ｶﾊﾞｰ組立16(ﾀﾞﾝﾊﾟｰ取付け)",
"WorkItems": [
"1. ②③にｸｯｼｮﾝ材を巻く",
"2. ①に1完成品をWASHER BOLT で取付"
],
"WorkPoints": [
"矢印方向に押し当てて取付",
"取付場所2か所あり",
"このﾀｯﾌﾟは使用しない",
"このﾀｯﾌﾟは使用しない",
"ﾎﾞﾙﾄ頭が内側へ向くこと",
"ﾎﾞﾙﾄ頭が内側へ向くこと",
"この作業では同じものを2個製作",
"取付目安 1.0㎜"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立1",
"WorkItems": [
"1. BRACKET にBRACKET HINGE をBOLT WASHER NUT で取付"
],
"WorkPoints": [
"内曲げが取付け面になるように",
"ﾋﾝｼﾞとﾌﾞﾗｹｯﾄの上面を合わせて取付",
"ﾋﾝｼﾞはﾓﾝｷｰｽﾊﾟﾅで90°に曲げてから取付ける事",
"目安としてﾋﾝｼﾞからの出しろが1mmになるように",
"この作業では同じものを2個製作"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立1",
"WorkItems": [
"1. BRACKET にBRACKET HINGE をBOLT WASHER NUT で取付"
],
"WorkPoints": [
"内曲げが取付け面になるように",
"ﾋﾝｼﾞとﾌﾞﾗｹｯﾄの上面を合わせて取付",
"ﾋﾝｼﾞはﾓﾝｷｰｽﾊﾟﾅで90°に曲げてから取付ける事",
"目安としてﾋﾝｼﾞからの出しろが1mmになるように",
"この作業では同じものを2個製作"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立2",
"WorkItems": [
"2. ﾃﾞｨｯﾌﾟｽｲｯﾁがOFFになっているかをﾁｪｯｸし検査書に記入",
"3. MONITOR に①をBOLT WASHER で取付",
"■1. MONITOR の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を記入"
],
"WorkPoints": [
"裏側",
"ﾓﾆﾀと平行に取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ2.0N･m"
],
"InspectionNo": "WETE-G002-D06",
"InspectionItems": [
"検査表①:3.ﾀｯﾁﾊﾟﾈﾙ (1) 型式･検査書ﾁｪｯｸ"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"全てOFFのこと",
"OFF",
"検査表①:3.ﾀｯﾁﾊﾟﾈﾙ (2) DIP SW設定確認",
"この作業では同じものを2個製作",
"WETE-G002-D06"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立2",
"WorkItems": [
"2. ﾃﾞｨｯﾌﾟｽｲｯﾁがOFFになっているかをﾁｪｯｸし検査書に記入",
"3. MONITOR に①をBOLT WASHER で取付",
"■1. MONITOR の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を記入"
],
"WorkPoints": [
"裏側",
"ﾓﾆﾀと平行に取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ2.0N･m"
],
"InspectionNo": "WETE-G002-D06",
"InspectionItems": [
"検査表①:3.ﾀｯﾁﾊﾟﾈﾙ (2) DIP SW設定確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"全てOFFのこと",
"OFF",
"検査表①:3.ﾀｯﾁﾊﾟﾈﾙ (1) 型式･検査書ﾁｪｯｸ",
"この作業では同じものを2個製作",
"WETE-G002-D06"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "2.0N･m",
"WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立2",
"WorkItems": [
"2. ﾃﾞｨｯﾌﾟｽｲｯﾁがOFFになっているかをﾁｪｯｸし検査書に記入",
"3. MONITOR に①をBOLT WASHER で取付",
"■1. MONITOR の型式をﾁｪｯｸし､ｼﾘｱﾙNo.を記入"
],
"WorkPoints": [
"裏側",
"ﾓﾆﾀと平行に取付ける事"
],
"Tolks": [
"締付ﾄﾙｸ2.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"全てOFFのこと",
"OFF",
"検査表①:3.ﾀｯﾁﾊﾟﾈﾙ (1) 型式･検査書ﾁｪｯｸ",
"検査表①:3.ﾀｯﾁﾊﾟﾈﾙ (2) DIP SW設定確認",
"この作業では同じものを2個製作",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ(全体ｶﾊﾞｰ)",
"Size": "",
"ToolOther": "FM-6617",
"WorkName": "ﾀｯﾁﾊﾟﾈﾙ組立3",
"WorkItems": [
"1. COVER にLABEL LABEL を貼付",
"2. COVER にLABEL を貼付",
"1. COVER にLABEL LABEL を貼付",
"2. COVER にLABEL を貼付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ACTIVATION",
"この作業では同じものを2個製作",
"㉗をセットし、貼付ける",
"㉗をセットし、貼付ける",
"ACTIVATION",
"この作業では同じものを2個製作",
"㉗をセットし、貼付ける",
"㉗をセットし、貼付ける"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6617",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "操作ﾊﾟﾈﾙSW組立1",
"WorkItems": [
"4. ②にSWITCH を取付",
"1. ①の裏面にCABLE-SUPPORT を取付",
"■2. SWITCH SWITCH SWITCH SWITCH SWITCH の型式･ｼﾘｱﾙNo.を確認",
"3. 1.完成品にSWITCH SWITCH SWITCH SWITCH を取付"
],
"WorkPoints": [
"F側､R側に区別しておく",
"SWITCH 取付け方向は△ﾏｰｸが上になるよう取付",
"△ﾏｰｸ",
"ｺﾈｸﾀ部",
"回り止め金具",
"取付けﾘﾝｸﾞ",
"SW部",
"突起がｶﾊﾞｰ側",
"取付後､傾き無き事",
"取付け方向は△ﾏｰｸが上になるよう取付",
"ｽｲｯﾁ部の取付けは下段SWITCH SWITCH から先に取付",
"この作業では同じものを2個製作"
],
"Tolks": [
"締付ﾄﾙｸ 125cN･m",
"締付ﾄﾙｸ 125cN･m"
],
"InspectionNo": "WETE-G002-D06",
"InspectionItems": [
"検査表①:F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ",
"検査表①:F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"STOP START",
"ACTIVATION",
"検査表①:R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ",
"検査表①:1.F-SWﾊﾟﾈﾙ (1)型式･検査書ﾁｪｯｸ",
"取付方法",
"検査表①:2.R-SWﾊﾟﾈﾙ (1)型式･検査書ﾁｪｯｸ",
"検査表①:R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ",
"WETE-G002-D06"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WETE-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｲｯﾁ締付けｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5255",
"WorkName": "操作ﾊﾟﾈﾙSW組立1",
"WorkItems": [
"4. ②にSWITCH を取付"
],
"WorkPoints": [
"△ﾏｰｸ",
"ｺﾈｸﾀ部",
"取付けﾘﾝｸﾞ",
"SW部",
"突起がｶﾊﾞｰ側",
"ｽｲｯﾁ部の取付けは下段SWITCH SWITCH から先に取付"
],
"Tolks": [
"締付ﾄﾙｸ 125cN･m",
"締付ﾄﾙｸ 125cN･m"
],
"InspectionNo": "WETE-G002-D06",
"InspectionItems": [
"検査表①:R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ",
"検査表①:R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"STOP START",
"検査表①:F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ",
"検査表①:F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ",
"■安全作業",
"WETE-G002-D06"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5255",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D06",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "FM-5255専用ﾋﾞｯﾄ",
"ToolOther": "125cN･m",
"WorkName": "操作ﾊﾟﾈﾙSW組立1",
"WorkItems": [
"4. ②にSWITCH を取付",
"4. ②にSWITCH を取付"
],
"WorkPoints": [
"△ﾏｰｸ",
"ｺﾈｸﾀ部",
"取付けﾘﾝｸﾞ",
"SW部",
"突起がｶﾊﾞｰ側",
"ｽｲｯﾁ部の取付けは下段SWITCH SWITCH から先に取付",
"△ﾏｰｸ",
"ｺﾈｸﾀ部",
"取付けﾘﾝｸﾞ",
"SW部",
"突起がｶﾊﾞｰ側",
"ｽｲｯﾁ部の取付けは下段SWITCH SWITCH から先に取付"
],
"Tolks": [
"締付ﾄﾙｸ 125cN･m",
"締付ﾄﾙｸ 125cN･m",
"締付ﾄﾙｸ 125cN･m",
"締付ﾄﾙｸ 125cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"■安全作業"
],
"Words": [
"STOP START",
"検査表①:F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ",
"検査表①:R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ",
"検査表①:F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ",
"検査表①:R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ",
"■安全作業",
"STOP START",
"検査表①:F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ",
"検査表①:R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ",
"検査表①:F-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ",
"検査表①:R-SWﾊﾟﾈﾙ(2)ｽｲｯﾁ配置ﾁｪｯｸ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "125cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "非常ｽｲｯﾁ締付けｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5254",
"WorkName": "操作ﾊﾟﾈﾙSW組立2",
"WorkItems": [
"1. ①②に⑥を取付"
],
"WorkPoints": [
"回り止め金具",
"取付けﾘﾝｸﾞ",
"SW部",
"SW部の凸型とｶﾊﾞｰ部･周り止めの凹型方向を合わせる",
"⑥は1工程前準備より貰い受ける事",
"組み合わせに注意(F側･R側)"
],
"Tolks": [
"締付ﾄﾙｸ 125cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5254",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "FM-5254専用ﾋﾞｯﾄ",
"ToolOther": "125cN･m",
"WorkName": "操作ﾊﾟﾈﾙSW組立2",
"WorkItems": [
"1. ①②に⑥を取付"
],
"WorkPoints": [
"回り止め金具",
"取付けﾘﾝｸﾞ",
"SW部",
"SW部の凸型とｶﾊﾞｰ部･周り止めの凹型方向を合わせる",
"⑥は1工程前準備より貰い受ける事",
"組み合わせに注意(F側･R側)"
],
"Tolks": [
"締付ﾄﾙｸ 125cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "125cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "操作ﾊﾟﾈﾙSW配線処理",
"WorkItems": [
"1. ①②にCABLE を接続しｲﾝｼｭﾛｯｸで固定"
],
"WorkPoints": [
"STOP",
"EXCH R",
"SERVO",
"START",
"ｺﾈｸﾀﾌﾞﾗｹｯﾄに取付ける",
"F側､R側に区別されているので注意",
"START､STOP､SERVO",
"EXCH L ､EXCH R",
"F/RSW1P",
"EXCH L",
"OK",
"NG",
"･ｺﾈｸﾀ配線部に過大な力を加え無い事･ｺﾈｸﾀ及びｹｰﾌﾞﾙに引っ張り力がかから無い事"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D06",
"InspectionItems": [
"検査表①:F-SWﾊﾟﾈﾙ(2)ｺﾈｸﾀ接続確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:R-SWﾊﾟﾈﾙ(2)ｺﾈｸﾀ接続確認",
"検査表②:R側ﾊﾟﾈﾙ､操作SW中継､ｶﾊﾞｰSW接続確認",
"検査表②:F側ﾊﾟﾈﾙ､操作SW中継､ｶﾊﾞｰSW接続確認",
"A矢視",
"WETE-G002-D06"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D06",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "操作ﾊﾟﾈﾙSW配線処理",
"WorkItems": [
"1. ①②にCABLE を接続しｲﾝｼｭﾛｯｸで固定"
],
"WorkPoints": [
"STOP",
"EXCH R",
"SERVO",
"START",
"ｺﾈｸﾀﾌﾞﾗｹｯﾄに取付ける",
"F側､R側に区別されているので注意",
"START､STOP､SERVO",
"EXCH L ､EXCH R",
"F/RSW1P",
"EXCH L",
"OK",
"NG",
"･ｺﾈｸﾀ配線部に過大な力を加え無い事･ｺﾈｸﾀ及びｹｰﾌﾞﾙに引っ張り力がかから無い事"
],
"Tolks": [],
"InspectionNo": "WETE-G002-D07",
"InspectionItems": [
"検査表②:R側ﾊﾟﾈﾙ､操作SW中継､ｶﾊﾞｰSW接続確認"
],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:F-SWﾊﾟﾈﾙ(2)ｺﾈｸﾀ接続確認",
"検査表①:R-SWﾊﾟﾈﾙ(2)ｺﾈｸﾀ接続確認",
"検査表②:F側ﾊﾟﾈﾙ､操作SW中継､ｶﾊﾞｰSW接続確認",
"A矢視",
"WETE-G002-D07"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-D07",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN組立1",
"WorkItems": [
"■1. FAN の型式ﾁｪｯｸをし､ｼﾘｱﾙNo.を検査表に記入",
"2. 1完成品にFAN-GUARD をSPACER BOLT WASHER WASHER で取付"
],
"WorkPoints": [
"型式確認",
"ｼﾘｱﾙ確認",
"F側､R側に区別しておく",
"ﾌｧﾝｶﾞｰﾄﾞの取付方向に注意すること",
"風向き方向を確認して取付"
],
"Tolks": [
"締付ﾄﾙｸ 152cN･m"
],
"InspectionNo": "WETE-G002-C14",
"InspectionItems": [
"検査表FAN :3.冷却FANの型式確認とｼﾘｱﾙNo.記録"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"この作業では同じものを2個製作",
"9GL1224J1J05",
"WETE-G002-C14"
]
} | {
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C14",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.