input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2可動側右側ﾍﾞｱ整線②",
"WorkItems": [
"1. TUBE に①のﾌｧｲﾊﾞｰを通す",
"2. CABLE-BEAR のふたを開け配線を入れる",
"3. CABLE-BEAR のふたを閉じて､ﾚｰﾙ側の固定金具に取付",
"4. 下側の固定金具に取付"
],
"WorkPoints": [
"L2側",
"L1側",
"通してあるｲﾝｼｭﾛｯｸにて固定",
"A矢視",
"上側",
"下側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"M625R",
"M627R",
"B1127P"
]
} | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "180cN･m",
"WorkName": "ﾚｰﾝ2可動側右側ﾍﾞｱ整線①",
"WorkItems": [
"■1. ①のFG線をSCREW で取付",
"2. 1完成品をｲﾝｼｭﾛｯｸで固定"
],
"WorkPoints": [
"FGCVM5"
],
"Tolks": [
"締付ﾄﾙｸ 180cN･m"
],
"InspectionNo": "WETE-G002-C04",
"InspectionItems": [
"検査表①:FG線接続とﾗﾍﾞﾙ確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "180cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側配線①",
"WorkItems": [
"1. ①にCABLE を引き回す"
],
"WorkPoints": [
"B122R"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側配線②",
"WorkItems": [
"1. ①にCABLE を引き回す"
],
"WorkPoints": [
"太線のみ板金と固定する事単線は単線のみで固定",
"配線が張らないようにする事",
"L2側",
"L1側",
"L1側",
"L2側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"B1120",
"B1121",
"B1122",
"B1123",
"【OP】B1130",
"【OP】B1131",
"B1124",
"B1125",
"B1132",
"B1133"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側配線①",
"WorkItems": [
"1. ①にCABLE を引き回す"
],
"WorkPoints": [
"B126R"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側配線②",
"WorkItems": [
"1. ①にCABLE の配線を固定"
],
"WorkPoints": [
"L2側",
"L1側",
"太線のみ板金と固定する事単線は単線のみで固定",
"配線が張らないようにする事",
"L1側",
"L2側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"【OP】B1031",
"【OP】B1030",
"B1023",
"B1022",
"B1021",
"B1020",
"B1033",
"B1032",
"B1025",
"B1024",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ1固定側ﾏｰｸﾁｭｰﾌﾞ挿入",
"WorkItems": [
"1. ①ﾌｧｲﾊﾞｰ線にMARK TUBE MARK TUBE を挿入"
],
"WorkPoints": [
"ｽﾗｲﾄﾞ搬送OP仕様"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"A矢視",
"B矢視",
"MARK TUBE ",
"MARK TUBE ",
"A矢視",
"B矢視"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ1可動側ﾏｰｸﾁｭｰﾌﾞ挿入",
"WorkItems": [
"1. ①ﾌｧｲﾊﾞｰ線にMARK TUBE MARK TUBE を挿入"
],
"WorkPoints": [
"ｽﾗｲﾄﾞ搬送OP仕様"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"A矢視",
"B矢視",
"MARK TUBE ",
"MARK TUBE ",
"A矢視",
"B矢視"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2固定側ﾏｰｸﾁｭｰﾌﾞ挿入",
"WorkItems": [
"1. ①ﾌｧｲﾊﾞｰ線にMARK TUBE MARK TUBE を挿入"
],
"WorkPoints": [
"ｽﾗｲﾄﾞ搬送OP仕様"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"A矢視",
"B矢視",
"MARK TUBE ",
"MARK TUBE ",
"A矢視",
"B矢視"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾚｰﾝ2可動側ﾏｰｸﾁｭｰﾌﾞ挿入",
"WorkItems": [
"1. ①ﾌｧｲﾊﾞｰ線にMARK TUBE MARK TUBE を挿入"
],
"WorkPoints": [
"ｽﾗｲﾄﾞ搬送OP仕様"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"A矢視",
"B矢視",
"MARK TUBE ",
"MARK TUBE ",
"A矢視",
"B矢視"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側配線ﾌﾞﾗｹｯﾄ固定側ﾌｧｲﾊﾞｰ引き回し確認",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰｾﾝｻの引き回し確認"
],
"WorkPoints": [
"図の通り引き回しされている事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側配線ﾌﾞﾗｹｯﾄ可動側ﾌｧｲﾊﾞｰ整線",
"WorkItems": [
"3. 2完成品にCABLE を引き回し",
"1. ①のﾌｧｲﾊﾞｰｾﾝｻを固定",
"2. JOINT にTUBE を接続"
],
"WorkPoints": [
"延長ｺﾝﾍﾞﾔｰ仕様時",
"通してあるｲﾝｼｭﾛｯｸに固定",
"TUBE ﾏｰｷﾝｸﾞ位置",
"延長仕様の場合､ﾊﾞﾙﾌﾞ側ｼﾞｮｲﾝﾄに接続",
"TUBE ﾏｰｷﾝｸﾞ位置",
"標準仕様時",
"TUBE に150㎜の位置でﾏｰｷﾝｸﾞ",
"ﾏｰｷﾝｸﾞ側にJOINT を接続",
"拡大図",
"標準仕様時ではCABLE は拡大図のように引き回す",
"R4237R",
"R4236R",
"延長ｺﾝﾍﾞﾔｰ仕様時ではCABLE はﾊﾞﾙﾌﾞに接続"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側ﾌｧｲﾊﾞｰ線接続",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰ線接続"
],
"WorkPoints": [
"付属のﾌｧｲﾊﾞｰｶｯﾀｰでｶｯﾄして接続する",
"上段:可動側(黄)",
"下段:固定側(白)",
"ﾌｧｲﾊﾞｰ線を奥まで挿入する事",
"ﾌｧｲﾊﾞｰﾛｯｸﾚﾊﾞｰがﾛｯｸされている事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B1033",
"B1032",
"B1025",
"B1024",
"B1023",
"B1022",
"B1021",
"B1020",
"【OP】B1031",
"【OP】B1030",
"ﾚｰﾝ1",
"ﾚｰﾝ2"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り配線･配管出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側配線ﾌﾞﾗｹｯﾄ固定側ﾌｧｲﾊﾞｰ引き回し確認",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰｾﾝｻの引き回し確認"
],
"WorkPoints": [
"図の通り引き回しされている事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2"
]
} | {
"QualityItem": "引き回し確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り引き回し出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側配線ﾌﾞﾗｹｯﾄ可動側ﾌｧｲﾊﾞｰ整線",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰｾﾝｻを固定"
],
"WorkPoints": [
"通してあるｲﾝｼｭﾛｯｸに固定"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾚｰﾝ1",
"ﾚｰﾝ2",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
} | {
"QualityItem": "整線確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り整線出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側ﾌｧｲﾊﾞｰｾﾝｻ接続",
"WorkItems": [
"1. ①のﾌｧｲﾊﾞｰ線接続"
],
"WorkPoints": [
"付属のﾌｧｲﾊﾞｰｶｯﾀｰでｶｯﾄして接続する",
"上段:可動側(黄)",
"下段:固定側(白)",
"ﾌｧｲﾊﾞｰ線を奥まで挿入する事",
"ﾌｧｲﾊﾞｰﾛｯｸﾚﾊﾞｰがﾛｯｸされている事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B1124",
"B1125",
"B1132",
"B1133",
"B1122",
"B1123",
"【OP】B1130",
"【OP】B1131",
"B1120",
"B1121",
"ﾚｰﾝ1",
"ﾚｰﾝ2"
]
} | {
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｱﾝﾌﾟｶﾊﾞｰ取付",
"WorkItems": [
"1. ①に②を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "幅寄せﾓｰﾀｰ取付",
"WorkItems": [
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"ﾋﾟﾝにしっかりはまっている事",
"取付前に㉚をシャフトに挿入しておく事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "幅寄せﾓｰﾀｰ取付",
"WorkItems": [
"2. 治具にてﾓｰﾀｰとｼｬﾌﾄの芯出し"
],
"WorkPoints": [
"治具を動かし､引っ掛かりが無い事",
"付属ﾎﾞﾙﾄ締結"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "100cN･m",
"WorkName": "幅寄せﾓｰﾀｰ取付",
"WorkItems": [
"3. 2完成品にCOUPLING を取付"
],
"WorkPoints": [
"目視にて青丸部隙間が均等になっている事",
"COUPLING は矢印方向に当てつけながら締結"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｶｯﾌﾟﾘﾝｸﾞ治具(Φ8×Φ8)",
"Size": "",
"ToolOther": "FM-1198",
"WorkName": "幅寄せﾓｰﾀｰ取付",
"WorkItems": [
"2. 治具にてﾓｰﾀｰとｼｬﾌﾄの芯出し",
"1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"治具を動かし､引っ掛かりが無い事",
"付属ﾎﾞﾙﾄ締結",
"ﾋﾟﾝにしっかりはまっている事",
"取付前に㉚をシャフトに挿入しておく事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1198",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "200cN･m",
"WorkName": "上側ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①に②をSCREW SCREW で取付"
],
"WorkPoints": [
"隙間が均等になるように取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 200cN･m",
"締付ﾄﾙｸ 350cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "200cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.3",
"ToolOther": "350cN･m",
"WorkName": "上側ｶﾊﾞｰ取付",
"WorkItems": [
"1. ①に②をSCREW SCREW で取付"
],
"WorkPoints": [
"隙間が均等になるように取付の事"
],
"Tolks": [
"締付ﾄﾙｸ 200cN･m",
"締付ﾄﾙｸ 350cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "350cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "前面扉取付-①",
"WorkItems": [
"1. ①に②をSCREW で取付"
],
"WorkPoints": [
"取付け方向",
"ﾌﾞﾛｯｸにて調整し平行に合わす",
"ﾌﾞﾛｯｸと扉の隙間無い事※扉がﾌﾞﾛｯｸの上に載っている事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "前面扉取付-①",
"WorkItems": [
"1. ①に②をSCREW で取付"
],
"WorkPoints": [
"取付け方向",
"ﾌﾞﾛｯｸにて調整し平行に合わす",
"ﾌﾞﾛｯｸと扉の隙間無い事※扉がﾌﾞﾛｯｸの上に載っている事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "前面扉取付‐②",
"WorkItems": [
"1. ①のﾎﾞｰﾙｷｬｯﾁ位置を調整する"
],
"WorkPoints": [
"隙間を均等に合わせる",
"2.0㎜±0.5㎜",
"片当たりなく合わせる事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"内側",
"外側"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "前面扉取付‐②",
"WorkItems": [
"1. ①のﾎﾞｰﾙｷｬｯﾁ位置を調整する"
],
"WorkPoints": [
"隙間を均等に合わせる",
"2.0㎜±0.5㎜",
"片当たりなく合わせる事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"内側",
"外側"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "前面扉取付‐③",
"WorkItems": [
"1. ①のﾏｸﾞﾈｯﾄｷｬｯﾁ位置を調整する",
"2. 前面扉のｶﾞﾀﾂｷの確認を行う"
],
"WorkPoints": [
"隙間を均等にする",
"ｶﾞﾀﾂｷ無き事",
"ﾏｸﾞﾈｯﾄｷｬｯﾁの傾き無き事",
"確認位置"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"内側",
"外側",
"検査表①:前面扉のｶﾞﾀﾂｷ確認",
"前面扉と保持部ﾌﾞﾗｹｯﾄの隙間",
"20㎜",
"20㎜",
"20㎜",
"20㎜",
"28㎜",
"ﾎﾞｰﾙｷｬｯﾁ",
"ﾏｸﾞﾈｯﾄｷｬｯﾁ"
]
} | {
"QualityItem": "取付位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "前面扉取付‐③",
"WorkItems": [
"1. ①のﾏｸﾞﾈｯﾄｷｬｯﾁ位置を調整する"
],
"WorkPoints": [
"隙間を均等にする"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"内側",
"外側"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前面扉取付‐③",
"WorkItems": [
"1. ①のﾏｸﾞﾈｯﾄｷｬｯﾁ位置を調整する",
"2. 前面扉のｶﾞﾀﾂｷの確認を行う"
],
"WorkPoints": [
"ｶﾞﾀﾂｷ無き事",
"隙間を均等にする",
"ﾏｸﾞﾈｯﾄｷｬｯﾁの傾き無き事",
"確認位置"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:前面扉のｶﾞﾀﾂｷ確認"
],
"WorkTypes": [],
"Words": [
"前面扉と保持部ﾌﾞﾗｹｯﾄの隙間",
"20㎜",
"20㎜",
"20㎜",
"20㎜",
"28㎜",
"内側",
"外側",
"ﾎﾞｰﾙｷｬｯﾁ",
"ﾏｸﾞﾈｯﾄｷｬｯﾁ",
"WETE-G002-A11"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｶﾞﾀつき無き事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "前面扉取付‐④",
"WorkItems": [
"1. ①のﾛｯｸｼﾘﾝﾀﾞｰを調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが接触なく出入りする事",
"傾き無き事",
"中心に合わせる事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"検査表①:前面扉ｽﾄｯﾊﾟｰ位置確認",
"■安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "前面扉取付‐④",
"WorkItems": [
"1. ①のﾛｯｸｼﾘﾝﾀﾞｰを調整する",
"■2. 安全SWの位置調整を行う"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが接触なく出入りする事",
"傾き無き事",
"中心に合わせる事",
"1~2.5㎜",
"SW固定ﾎﾞﾙﾄを合わす",
"ｽｲｯﾁ同士のｽﾞﾚ無き事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:前面扉ｽﾄｯﾊﾟｰ位置確認"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ON",
"OFF",
"検査表①:前面扉安全SWの位置調整",
"WETE-G002-A11"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "干渉なく出入りする事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "前面扉取付‐④",
"WorkItems": [
"■2. 安全SWの位置調整を行う"
],
"WorkPoints": [
"1~2.5㎜",
"SW固定ﾎﾞﾙﾄを合わす",
"ｽｲｯﾁ同士のｽﾞﾚ無き事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:前面扉安全SWの位置調整"
],
"WorkTypes": [
"■安全作業"
],
"Words": [
"ON",
"OFF",
"■安全作業"
]
} | {
"QualityItem": "位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間1㎜~2.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｱｸﾘﾙ開閉ｶﾊﾞｰ調整",
"WorkItems": [
"1. ①の補給部PC開閉ｶﾊﾞｰ段差調整"
],
"WorkPoints": [
"段差:0.5~2.0㎜",
"傾き無い事"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.5~2.0㎜",
"検査表①:補給部PC開閉ｶﾊﾞｰの段差確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "50cN･m",
"WorkName": "ｱｸﾘﾙ開閉ｶﾊﾞｰ調整",
"WorkItems": [
"1. ①の補給部PC開閉ｶﾊﾞｰ段差調整",
"2. ｽｲｯﾁ調整"
],
"WorkPoints": [
"段差:0.5~2.0㎜",
"傾き無い事",
"傾き無い事",
"均等に隙間が確保されている事",
"ｽｲｯﾁがONをしてﾚﾊﾞｰに余裕がある事"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.5~2.0㎜",
"検査表①:補給部PC開閉ｶﾊﾞｰの段差確認",
"(2.0㎜)",
"前面扉",
"PCｶﾊﾞｰ",
"ｽｲｯﾁ",
"ﾚﾊﾞｰ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｱｸﾘﾙ開閉ｶﾊﾞｰ調整",
"WorkItems": [
"1. ①の補給部PC開閉ｶﾊﾞｰ段差調整"
],
"WorkPoints": [
"段差:0.5~2.0㎜",
"傾き無い事"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:補給部PC開閉ｶﾊﾞｰの段差確認"
],
"WorkTypes": [],
"Words": [
"0.5~2.0㎜"
]
} | {
"QualityItem": "位置確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間0.5㎜~2.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "左側ｼｬｯﾀｰｼｬﾌﾄ取付",
"WorkItems": [
"1. SHAFT にBOLT WASHER を仮取付",
"2. 1完成品を①に挿入し固定ﾎﾞﾙﾄを仮止め"
],
"WorkPoints": [
"ﾎﾞﾙﾄ側が上",
"ｼｬｯﾀｰｼｬﾌﾄ挿入穴",
"ｼｬｯﾀｰｼｬﾌﾄ挿入穴",
"Dｶｯﾄ",
"Dｶｯﾄをﾎﾞﾙﾄ側に合わせる",
"Dｶｯﾄ",
"Dｶｯﾄをﾎﾞﾙﾄ側に合わせる",
"固定ﾎﾞﾙﾄ",
"固定ﾎﾞﾙﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"仮止め:SD-A051313-408にて本締め",
"左側上ｱｰﾑ",
"左側下ｱｰﾑ",
"仮止め:SD-A041086-408にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "左側ｼｬｯﾀｰｼｬﾌﾄ調整",
"WorkItems": [
"1. ｼｬｯﾀｰ調整を行う"
],
"WorkPoints": [
"当付け",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"･ｴｱｰON･ｼｬｯﾀｰ開ｱｰﾑとｽﾄｯﾊﾟｰの隙間を確認0.01㎜ｼﾑが入ら無い事",
"ｼｬｯﾀｰを開きｽﾄｯﾊﾟｰﾎﾞﾙﾄに当てた状態で上下ｼｬﾌﾄ取付ﾎﾞﾙﾄを仮止め",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"当付け"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "左側ｼｬｯﾀｰｼｬﾌﾄ調整",
"WorkItems": [
"1. ｼｬｯﾀｰ調整を行う"
],
"WorkPoints": [
"当付け",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"･ｴｱｰON･ｼｬｯﾀｰ開ｱｰﾑとｽﾄｯﾊﾟｰの隙間を確認0.01㎜ｼﾑが入ら無い事",
"ｼｬｯﾀｰを開きｽﾄｯﾊﾟｰﾎﾞﾙﾄに当てた状態で上下ｼｬﾌﾄ取付ﾎﾞﾙﾄを仮止め",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"当付け"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "左側ｼｬｯﾀｰｼｬﾌﾄ調整",
"WorkItems": [
"1. ｼｬｯﾀｰ調整を行う"
],
"WorkPoints": [
"当付け",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"･ｴｱｰON･ｼｬｯﾀｰ開ｱｰﾑとｽﾄｯﾊﾟｰの隙間を確認0.01㎜ｼﾑが入ら無い事",
"ｼｬｯﾀｰを開きｽﾄｯﾊﾟｰﾎﾞﾙﾄに当てた状態で上下ｼｬﾌﾄ取付ﾎﾞﾙﾄを仮止め",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"当付け"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "右側ｼｬｯﾀｰｼｬﾌﾄ取付",
"WorkItems": [
"1. SHAFT にBOLT WASHER を仮取付",
"2. 1完成品を①に挿入し固定ﾎﾞﾙﾄを仮止め"
],
"WorkPoints": [
"左側上ﾌﾟﾚｰﾄ",
"ｼｬｯﾀｰｼｬﾌﾄ挿入穴",
"ｼｬｯﾀｰｼｬﾌﾄ挿入穴",
"ﾎﾞﾙﾄ側が上",
"Dｶｯﾄをﾎﾞﾙﾄ側に合わせる",
"Dｶｯﾄ",
"固定ﾎﾞﾙﾄ",
"Dｶｯﾄ",
"Dｶｯﾄをﾎﾞﾙﾄ側に合わせる",
"固定ﾎﾞﾙﾄ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"右側上ｱｰﾑ",
"仮止め:SD-A041086-410にて本締め",
"右側下ｱｰﾑ",
"仮止め:SD-A041086-410にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視手感",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "右側ｼｬｯﾀｰｼｬﾌﾄ調整",
"WorkItems": [
"1. ｼｬｯﾀｰ調整を行う"
],
"WorkPoints": [
"ｼｬｯﾀｰを開きｽﾄｯﾊﾟｰﾎﾞﾙﾄに当てた状態で上下ｼｬﾌﾄ取付ﾎﾞﾙﾄを仮止め",
"当付け",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"･ｴｱｰON･ｼｬｯﾀｰ開ｱｰﾑとｽﾄｯﾊﾟｰの隙間を確認0.01㎜ｼﾑが入ら無い事",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "右側ｼｬｯﾀｰｼｬﾌﾄ調整",
"WorkItems": [
"1. ｼｬｯﾀｰ調整を行う"
],
"WorkPoints": [
"ｼｬｯﾀｰを開きｽﾄｯﾊﾟｰﾎﾞﾙﾄに当てた状態で上下ｼｬﾌﾄ取付ﾎﾞﾙﾄを仮止め",
"当付け",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"･ｴｱｰON･ｼｬｯﾀｰ開ｱｰﾑとｽﾄｯﾊﾟｰの隙間を確認0.01㎜ｼﾑが入ら無い事",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "右側ｼｬｯﾀｰｼｬﾌﾄ調整",
"WorkItems": [
"1. ｼｬｯﾀｰ調整を行う"
],
"WorkPoints": [
"ｼｬｯﾀｰを開きｽﾄｯﾊﾟｰﾎﾞﾙﾄに当てた状態で上下ｼｬﾌﾄ取付ﾎﾞﾙﾄを仮止め",
"当付け",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"･ｴｱｰON･ｼｬｯﾀｰ開ｱｰﾑとｽﾄｯﾊﾟｰの隙間を確認0.01㎜ｼﾑが入ら無い事",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄとの隙間無い事",
"ｽﾄｯﾊﾟｰﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(ﾒｶｽﾄｯﾊﾟｰ位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"3. 下側ｼｬｯﾀｰ部の位置を調整する",
"1. ①のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置(原点)まで下降させる"
],
"WorkPoints": [
"ｼｬﾌﾄ両側を治具に当付ける(左右のﾎﾞﾙﾄにて固定する)",
"治具を当付け隙間無い事(0.01㎜)",
"原点位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(ﾒｶｽﾄｯﾊﾟｰ位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"3. 下側ｼｬｯﾀｰ部の位置を調整する",
"1. ①のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置(原点)まで下降させる"
],
"WorkPoints": [
"ｼｬﾌﾄ両側を治具に当付ける(左右のﾎﾞﾙﾄにて固定する)",
"治具を当付け隙間無い事(0.01㎜)",
"原点位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.94N･m",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(ﾒｶｽﾄｯﾊﾟｰ位置)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"上面",
"ｼｬﾌﾄ",
"ｼｬﾌﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(ﾒｶｽﾄｯﾊﾟｰ位置)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除治具(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(ﾒｶｽﾄｯﾊﾟｰ位置)",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(LMｶﾞｲﾄﾞ上端位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"1.①のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置まで上昇する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.01㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(LMｶﾞｲﾄﾞ上端位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"1.①のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置まで上昇する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.01㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.94N･m",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(LMｶﾞｲﾄﾞ上端位置)",
"WorkItems": [
"3. 上側ｼｬｯﾀｰ部の位置を調整する"
],
"WorkPoints": [
"ｼｬﾌﾄを治具に当付ける",
"治具を当付け隙間無い事(0.01㎜)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"調整ﾎﾞﾙﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(LMｶﾞｲﾄﾞ上端位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"1.①のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置まで上昇する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除治具(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(LMｶﾞｲﾄﾞ上端位置)",
"WorkItems": [
"2. 治具をｾｯﾄする",
"1.①のﾘﾌﾄ軸をﾒｶｽﾄｯﾊﾟｰ位置まで上昇する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(隙間確認)",
"WorkItems": [
"1. 各隙間を確認する"
],
"WorkPoints": [
"NG排出位置",
"上段23段目位置",
"NG排出､(-)側ﾒｶｽﾄｯﾊﾟｰ①②→0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事上段23段目①②→0.15㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事全ての各個所③④→0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"(ｰ)ﾒｶｽﾄ位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｼｬﾌﾄ位置の確認"
]
} | {
"QualityItem": "位置確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けできていること",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(隙間確認)",
"WorkItems": [
"1. 各隙間を確認する"
],
"WorkPoints": [
"NG排出位置",
"上段23段目位置",
"NG排出､(-)側ﾒｶｽﾄｯﾊﾟｰ①②→0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事上段23段目①②→0.15㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事全ての各個所③④→0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"(ｰ)ﾒｶｽﾄ位置"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:ｼｬﾌﾄ位置の確認"
],
"WorkTypes": [],
"Words": [
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.02㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(隙間確認)",
"WorkItems": [
"1. 各隙間を確認する"
],
"WorkPoints": [
"NG排出位置",
"上段23段目位置",
"NG排出､(-)側ﾒｶｽﾄｯﾊﾟｰ①②→0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事上段23段目①②→0.15㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事全ての各個所③④→0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"(ｰ)ﾒｶｽﾄ位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｼｬﾌﾄ位置の確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.05㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.02㎜",
"ToolOther": "",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(隙間確認)",
"WorkItems": [
"1. 各隙間を確認する"
],
"WorkPoints": [
"NG排出位置",
"上段23段目位置",
"NG排出､(-)側ﾒｶｽﾄｯﾊﾟｰ①②→0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事上段23段目①②→0.15㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事全ての各個所③④→0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"(ｰ)ﾒｶｽﾄ位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｼｬﾌﾄ位置の確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.15㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(隙間確認)",
"WorkItems": [
"1. 各隙間を確認する"
],
"WorkPoints": [
"NG排出位置",
"上段23段目位置",
"NG排出､(-)側ﾒｶｽﾄｯﾊﾟｰ①②→0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事上段23段目①②→0.15㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事全ての各個所③④→0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"(ｰ)ﾒｶｽﾄ位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｼｬﾌﾄ位置の確認"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "ﾏｶﾞｼﾞﾝｼｬｯﾀｰ調整(隙間確認)",
"WorkItems": [
"1. 各隙間を確認する"
],
"WorkPoints": [
"NG排出位置",
"上段23段目位置",
"NG排出､(-)側ﾒｶｽﾄｯﾊﾟｰ①②→0.05㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事上段23段目①②→0.15㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事全ての各個所③④→0.02㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"(ｰ)ﾒｶｽﾄ位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｼｬﾌﾄ位置の確認"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "前面扉ｶﾞｲﾄﾞﾞ隙間調整",
"WorkItems": [
"1. ①にﾏｶﾞｼﾞﾝ､ﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 1完成品のﾄﾚｲﾊﾟﾚｯﾄと前面扉ｶﾞｲﾄﾞの隙間を調整する"
],
"WorkPoints": [
"通し:0.4㎜ 止まり:0.5㎜",
"ﾏｶﾞｼﾞﾝｼｬｯﾀｰ閉のこと",
"ﾏｶﾞｼﾞﾝ上下段に挿入",
"ﾄﾚｲﾊﾟﾚｯﾄ各5･19ｽﾛｯﾄに挿入",
"ﾄﾚｲﾊﾟﾚｯﾄをｼｬﾌﾄに当付ける",
"説明の為に前面扉は消しています"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:前面扉ｶﾞｲﾄﾞﾞの確認"
],
"WorkTypes": [],
"Words": [
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.4㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "前面扉ｶﾞｲﾄﾞﾞ隙間調整",
"WorkItems": [
"1. ①にﾏｶﾞｼﾞﾝ､ﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 1完成品のﾄﾚｲﾊﾟﾚｯﾄと前面扉ｶﾞｲﾄﾞの隙間を調整する"
],
"WorkPoints": [
"通し:0.4㎜ 止まり:0.5㎜",
"ﾏｶﾞｼﾞﾝｼｬｯﾀｰ閉のこと",
"ﾏｶﾞｼﾞﾝ上下段に挿入",
"ﾄﾚｲﾊﾟﾚｯﾄ各5･19ｽﾛｯﾄに挿入",
"ﾄﾚｲﾊﾟﾚｯﾄをｼｬﾌﾄに当付ける",
"説明の為に前面扉は消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:前面扉ｶﾞｲﾄﾞﾞの確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "前面扉ｶﾞｲﾄﾞﾞ隙間調整",
"WorkItems": [
"1. ①にﾏｶﾞｼﾞﾝ､ﾄﾚｲﾊﾟﾚｯﾄをｾｯﾄする",
"2. 1完成品のﾄﾚｲﾊﾟﾚｯﾄと前面扉ｶﾞｲﾄﾞの隙間を調整する"
],
"WorkPoints": [
"通し:0.4㎜ 止まり:0.5㎜",
"ﾏｶﾞｼﾞﾝｼｬｯﾀｰ閉のこと",
"ﾏｶﾞｼﾞﾝ上下段に挿入",
"ﾄﾚｲﾊﾟﾚｯﾄ各5･19ｽﾛｯﾄに挿入",
"ﾄﾚｲﾊﾟﾚｯﾄをｼｬﾌﾄに当付ける",
"説明の為に前面扉は消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:前面扉ｶﾞｲﾄﾞﾞの確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "1.94N･m",
"WorkName": "前面扉押込み防止ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"1. ①の押込み防止ｽﾄｯﾊﾟｰとﾌﾚｰﾑの隙間を調整する"
],
"WorkPoints": [
"説明の為に前面扉は消しています",
"ﾌﾚｰﾑに当付ける",
"平行に取付け"
],
"Tolks": [
"締付ﾄﾙｸ 1.94N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.94N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "補給部前側ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"1. ①にﾄﾚｲﾊﾟﾚｯﾄを挿入し補給部ｽﾄｯﾊﾟｰを調整する",
"2. 補給部ｽﾄｯﾊﾟｰの隙間を確認する"
],
"WorkPoints": [
"1､ ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰを隙間なく当付け調整する2 ､ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰを調整する",
"ﾄﾚｲﾊﾟﾚｯﾄをｼｬｯﾀｰｼｬﾌﾄに当付ける",
"0.4㎜が通り0.5㎜が通ら無い事",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰに当付ける"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:補給部ｽﾄｯﾊﾟｰの確認"
],
"WorkTypes": [],
"Words": [
"0.4㎜が通り0.5㎜が通ら無い事",
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰ",
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.4㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "補給部前側ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"1. ①にﾄﾚｲﾊﾟﾚｯﾄを挿入し補給部ｽﾄｯﾊﾟｰを調整する",
"2. 補給部ｽﾄｯﾊﾟｰの隙間を確認する"
],
"WorkPoints": [
"1､ ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰを隙間なく当付け調整する2 ､ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰを調整する",
"ﾄﾚｲﾊﾟﾚｯﾄをｼｬｯﾀｰｼｬﾌﾄに当付ける",
"0.4㎜が通り0.5㎜が通ら無い事",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰに当付ける"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.4㎜が通り0.5㎜が通ら無い事",
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰ",
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"検査表①:補給部ｽﾄｯﾊﾟｰの確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "補給部前側ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"1. ①にﾄﾚｲﾊﾟﾚｯﾄを挿入し補給部ｽﾄｯﾊﾟｰを調整する"
],
"WorkPoints": [
"1､ ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰを隙間なく当付け調整する2 ､ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰを調整する",
"ﾄﾚｲﾊﾟﾚｯﾄをｼｬｯﾀｰｼｬﾌﾄに当付ける"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.4㎜が通り0.5㎜が通ら無い事",
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰ",
"ｱｸﾘﾙｶﾊﾞｰｽﾄｯﾊﾟｰﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄｽﾄｯﾊﾟｰﾎﾞﾙﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "NG排出部ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"1. ①のNG排出部にﾄﾚｲﾊﾟﾚｯﾄを挿入する",
"2. NG排出ｽﾄｯﾊﾟｰを調整する"
],
"WorkPoints": [
"ｼｬｯﾀｰｼｬﾌﾄに当付け"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:NG排出部ｽﾄｯﾊﾟｰの確認"
],
"WorkTypes": [],
"Words": [
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.4㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.4㎜",
"ToolOther": "",
"WorkName": "NG排出部ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"1. ①のNG排出部にﾄﾚｲﾊﾟﾚｯﾄを挿入する",
"2. NG排出ｽﾄｯﾊﾟｰを調整する"
],
"WorkPoints": [
"ｼｬｯﾀｰｼｬﾌﾄに当付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:NG排出部ｽﾄｯﾊﾟｰの確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.5㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "NG排出部ｽﾄｯﾊﾟｰ調整",
"WorkItems": [
"1. ①のNG排出部にﾄﾚｲﾊﾟﾚｯﾄを挿入する",
"2. NG排出ｽﾄｯﾊﾟｰを調整する"
],
"WorkPoints": [
"ｼｬｯﾀｰｼｬﾌﾄに当付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:NG排出部ｽﾄｯﾊﾟｰの確認"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "補給部ﾗﾍﾞﾙ貼付け",
"WorkItems": [
"1. ①にLABEL を貼付ける"
],
"WorkPoints": [
"ﾗﾍﾞﾙの端面がﾄﾚｲﾊﾟﾚｯﾄに隠れ無い事",
"ｱﾙｺｰﾙ使用時には保護ﾒｶﾞﾈ着用の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"60㎜",
"60㎜"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾁｪｯｶｰ接続と立ち上げ",
"WorkItems": [
"3. PC画面が立ち上がったらNPM-GWのｱｲｺﾝをﾀﾞﾌﾞﾙｸﾘｯｸ",
"5. ｼｽﾃﾑ立ち上げ",
"1. ﾄﾚｲ本体とﾁｪｯｶｰを接続する",
"2. ﾁｪｯｶｰのﾊﾟｿｺﾝの立ち上げ",
"4.ﾁｪｯｶｰの電源BOXとｻｰﾎﾞSWをON"
],
"WorkPoints": [
"･ﾁｪｯｶｰ電源接続･ﾒｲﾝｴｱｰ接続･ｴｱｰ配管･ｺﾈｸﾀ大-TRAY･S ･･･内側 ･ｺﾈｸﾀ小-TRAY･P ･･･外側 各々接続",
"FM-2294",
"部署等を入力",
"ﾊﾞｰｺｰﾄﾞﾘｰﾀﾞｰでQRｺｰﾄﾞを読み取り",
"ﾊﾞｰｺｰﾄﾞ情報入力",
"PnP情報書込み",
"PnP情報書込み完了",
"ON",
"ﾊﾞｰｺｰﾄﾞﾘｰﾀﾞｰがUSBﾎﾟｰﾄに挿入されているのを確認する",
"ON",
"ﾄﾚｲﾌｨｰﾀﾞ本体の電源が入り待機状態になる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "接続確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整①",
"WorkItems": [
"1. 原点復帰を行う",
"2. 補給部ｼｬｯﾀｰの開閉を行い\"閉\"にする",
"1. 原点復帰を行う",
"2. 補給部ｼｬｯﾀｰの開閉を行い\"閉\"にする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B矢視",
"検査表①:飛び出し防止ｼﾘﾝﾀﾞｰ確認",
"A矢視",
"調整ﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.6㎜ｼｯｸﾈｽｹﾞｰｼﾞが通る事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B矢視",
"検査表①:飛び出し防止ｼﾘﾝﾀﾞｰ確認",
"A矢視",
"調整ﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.8㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B矢視",
"検査表①:飛び出し防止ｼﾘﾝﾀﾞｰ確認",
"A矢視",
"調整ﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B矢視",
"検査表①:飛び出し防止ｼﾘﾝﾀﾞｰ確認",
"A矢視",
"調整ﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "補給部奥側ｽﾄｯﾊﾟｰ調整②",
"WorkItems": [
"1. ﾄﾚｲﾊﾟﾚｯﾄとｽﾄｯﾊﾟｰの間を調整する"
],
"WorkPoints": [
"ｼﾘﾝﾀﾞｰが傾きが無いように取付",
"通し:t0.6㎜･止まり:t0.8㎜",
"通し:t0.10㎜･止まり:t0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"B矢視",
"検査表①:飛び出し防止ｼﾘﾝﾀﾞｰ確認",
"A矢視",
"調整ﾎﾞﾙﾄ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"ﾄﾚｲﾊﾟﾚｯﾄ",
"ｽﾄｯﾊﾟｰ",
"WETE-G002-A11"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.15㎜ｼｯｸﾈｽｹﾞｰｼﾞが止まる事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸原点登録",
"WorkItems": [
"2. TP軸をﾊﾟﾜｰONする",
"3. TP軸原点登録",
"1. ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄを緩める",
"4. TP軸原点ｾﾝｻ調整"
],
"WorkPoints": [
"ﾊﾟﾜｰOFFでﾚﾊﾞｰを原点付近へ動かす",
"ﾚﾊﾞｰが原点を探し動き始め原点確認後停止する",
"ﾒｶｽﾄｯﾊﾟｰ端面",
"稼働部ﾌﾟﾚｰﾄ端面",
"メカスト端面と稼働プレート端面に㉘を挟み込み、その位置でプーリーのボルトを締め付け",
"㉖でTP軸を動作させ、原点から『0.9㎜』で投光、『1.0㎜』で遮光の位置でセンサ位置を調整する",
"画面上で①②③④のﾎﾞﾀﾝを順次押すとﾊﾟﾜｰONとなる",
"プーリーの固定が完了したら、㉘を取り外し、㉖にて原点復帰の確認を行う",
"TP軸を原点復帰する",
"TP軸原点ｾﾝｻﾄﾞｸﾞ",
"TP軸原点ｾﾝｻ",
"ｾﾝｻ位置調整ﾎﾞﾙﾄ",
"SD-AD051313-441で本締め"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:引き出軸(TP軸)原点位置ｽﾄﾛｰｸ位置調整"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "引き出し部調整治具",
"Size": "",
"ToolOther": "FM-6646",
"WorkName": "TP軸原点登録",
"WorkItems": [
"3. TP軸原点登録",
"1. ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄを緩める",
"4. TP軸原点ｾﾝｻ調整"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6646",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付られている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TP軸原点登録",
"WorkItems": [],
"WorkPoints": [
"ﾚﾊﾞｰが原点を探し動き始め原点確認後停止する",
"ﾒｶｽﾄｯﾊﾟｰ端面",
"㉖でTP軸を動作させ、原点から『0.9㎜』で投光、『1.0㎜』で遮光の位置でセンサ位置を調整する",
"プーリーの固定が完了したら、㉘を取り外し、㉖にて原点復帰の確認を行う",
"TP軸原点ｾﾝｻﾄﾞｸﾞ",
"ｾﾝｻ位置調整ﾎﾞﾙﾄ"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:引き出軸(TP軸)原点位置ｽﾄﾛｰｸ位置調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TP軸原点登録",
"WorkItems": [
"2. TP軸をﾊﾟﾜｰONする",
"3. TP軸原点登録",
"1. ｶｯﾌﾟﾘﾝｸﾞﾎﾞﾙﾄを緩める",
"4. TP軸原点ｾﾝｻ調整"
],
"WorkPoints": [
"ﾊﾟﾜｰOFFでﾚﾊﾞｰを原点付近へ動かす",
"ﾚﾊﾞｰが原点を探し動き始め原点確認後停止する",
"ﾒｶｽﾄｯﾊﾟｰ端面",
"稼働部ﾌﾟﾚｰﾄ端面",
"メカスト端面と稼働プレート端面に㉘を挟み込み、その位置でプーリーのボルトを締め付け",
"㉖でTP軸を動作させ、原点から『0.9㎜』で投光、『1.0㎜』で遮光の位置でセンサ位置を調整する",
"画面上で①②③④のﾎﾞﾀﾝを順次押すとﾊﾟﾜｰONとなる",
"プーリーの固定が完了したら、㉘を取り外し、㉖にて原点復帰の確認を行う",
"TP軸を原点復帰する",
"TP軸原点ｾﾝｻﾄﾞｸﾞ",
"TP軸原点ｾﾝｻ",
"ｾﾝｻ位置調整ﾎﾞﾙﾄ",
"SD-AD051313-441で本締め"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:引き出軸(TP軸)原点位置ｽﾄﾛｰｸ位置調整"
],
"WorkTypes": [],
"Words": [
"WETE-G002-A11"
]
} | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが0.9㎜で投光1.0㎜で遮光する事",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整①",
"WorkItems": [
"1. ﾊﾟﾜｰONする",
"2. TL軸原点復帰を行う",
"3. 引き出部を原点位置から下段23Slot高さへ移動する"
],
"WorkPoints": [
"画面上で①②③④のﾎﾞﾀﾝを順次押すとﾊﾟﾜｰONとなる",
"ﾊﾟﾜｰOFFでﾚﾊﾞｰを原点付近へ動かす",
"FM-2848治具が取付いて無い事を確認｡ﾚﾊﾞｰが回転して危険です",
"SW ONから動き出しまでﾀｲﾑﾗｸﾞが有るので注意のこと",
"原点位置まで下降する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ﾘﾌﾄ上昇"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"4. 治具を取付ける",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"この時の高さの差を把握する事",
"FM-1934を引き出部へ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"FM-1934",
"±0.05mm以内(中央)±0.2mm以内(左右)"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "調整用ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM-5519",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す",
"2. 各治具をｾｯﾄする",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す"
],
"WorkPoints": [
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"FM-1934を引き出部へ",
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"FM-1934を引き出部へ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5519",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾀﾞｲﾚｸﾄﾄﾚｲﾌｨｰﾀﾞJIG",
"Size": "",
"ToolOther": "FM-1934",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"4. 治具を取付ける",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"この時の高さの差を把握する事",
"FM-1934を引き出部へ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"FM-1934",
"±0.05mm以内(中央)±0.2mm以内(左右)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1934",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"2. 各治具をｾｯﾄする",
"3. 引き出部側を基準に測定する",
"1. ㉖のマガジンシャッターを開を押す"
],
"WorkPoints": [
"FM-5519をﾏｶﾞｼﾞﾝ保持部 下段へ",
"FM-1934を引き出部へ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "中央:±0.05㎜以内左右:±0.2㎜以内",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"4. 治具を取付ける"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整②",
"WorkItems": [
"4. 治具を取付ける"
],
"WorkPoints": [
"A0",
"A 1",
"A 2",
"この時の高さの差を把握する事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整③",
"WorkItems": [
"3. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを締付",
"4. ﾘﾌﾄ上下治具を取り外し",
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"5. 各治具を取り出す",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-1934",
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"±0.05mm以内(中央)±0.2mm以内(左右)"
]
} | {
"QualityItem": "設定確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りの手順である事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整③",
"WorkItems": [
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "高さ確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取外す事",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾀﾞｲﾚｸﾄﾄﾚｲﾌｨｰﾀﾞJIG",
"Size": "",
"ToolOther": "FM-1934",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整③",
"WorkItems": [
"3. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを締付",
"4. ﾘﾌﾄ上下治具を取り外し",
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"5. 各治具を取り出す",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"FM-1934",
"引き出部搬送面",
"下段23ｽﾛｯﾄ高さ",
"FM-5519",
"ﾏｶﾞｼﾞﾝ保持部",
"引き出部",
"A1A0A2",
"±0.05mm以内(中央)±0.2mm以内(左右)"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-1934",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付けられている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "調整用ﾏｶﾞｼﾞﾝ",
"Size": "",
"ToolOther": "FM-5519",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整③",
"WorkItems": [
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-5519",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾘﾌﾄ軸ﾌﾞﾚｰｷ付きﾊﾝﾄﾞﾙ",
"Size": "",
"ToolOther": "FM-2848",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整③",
"WorkItems": [
"1. ｶｯﾌﾟﾘﾝｸﾞのﾎﾞﾙﾄを緩める",
"2. 引き出部を下段23ｽﾛｯﾄに㉗で高さを合わせる",
"5. 各治具を取り出す"
],
"WorkPoints": [
"※説明の為､供給部消しています"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-2848",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾚｰｷ解除ｼﾞｸﾞ(WX24V)",
"Size": "",
"ToolOther": "FM-5516",
"WorkName": "TL軸とﾏｶﾞｼﾞﾝ保持部の高さ調整③",
"WorkItems": [
"5. 各治具を取り出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "取外し確認",
"ToolManageNo": "FM-5516",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄ調整(-側ORｾﾝｻ調整)",
"WorkItems": [
"2. TL軸ﾏﾆｭｱﾙ動作で0.1mm入力する",
"1. TL軸を原点復帰する",
"3. ㉙をDOGにセットしO/Rセンサ位置を調整する（原点から＋0.1㎜で投光、原点で遮光）",
"2. TL軸ﾏﾆｭｱﾙ動作で0.1mm入力する",
"1. TL軸を原点復帰する",
"3. ㉙をDOGにセットしO/Rセンサ位置を調整する（原点から＋0.1㎜で投光、原点で遮光）"
],
"WorkPoints": [
"O/Rｾﾝｻが遮光する事",
"傾き無き事",
"+0.1㎜で投光､原点で遮光が確認出来たら増し締め"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "ｽﾄﾛｰｸ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｾﾝｻが0.1㎜で投光、原点で遮光する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "ﾛﾝｸﾞﾋﾞｯﾄ2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄ調整(-側ORｾﾝｻ調整)",
"WorkItems": [
"2. TL軸ﾏﾆｭｱﾙ動作で0.1mm入力する",
"1. TL軸を原点復帰する",
"3. ㉙をDOGにセットしO/Rセンサ位置を調整する（原点から＋0.1㎜で投光、原点で遮光）"
],
"WorkPoints": [
"O/Rｾﾝｻが遮光する事",
"傾き無き事",
"+0.1㎜で投光､原点で遮光が確認出来たら増し締め"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "TL軸ﾏｲﾅｽﾘﾐｯﾄ調整治具",
"Size": "",
"ToolOther": "FM-6449",
"WorkName": "TL軸ﾏｲﾅｽﾘﾐｯﾄ調整(-側ORｾﾝｻ調整)",
"WorkItems": [
"2. TL軸ﾏﾆｭｱﾙ動作で0.1mm入力する",
"1. TL軸を原点復帰する",
"3. ㉙をDOGにセットしO/Rセンサ位置を調整する（原点から＋0.1㎜で投光、原点で遮光）"
],
"WorkPoints": [
"O/Rｾﾝｻが投光",
"㉙を矢印方向に当付け"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"0.1㎜",
"調整箇所"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6449",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "傾き無き事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "NPM-GWﾄﾚｲ完成ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾌｧｰﾑﾊﾞｰｼﾞｮﾝ確認とｴｰｼﾞﾝｸﾞ実施",
"WorkItems": [
"2. ｴｰｼﾞﾝｸﾞの実施",
"1. ﾁｪｯｶｰ画面に表示されてあるﾌｧｰﾑﾊﾞｰｼﾞｮﾝを確認"
],
"WorkPoints": [
"ﾌｧｰﾑﾊﾞｰｼﾞｮﾝを記録する",
"ｴﾗｰ停止無い事",
"高速になっている事を確認",
"ﾁｪｯｶｰ画面で90ｻｲｸﾙを入力し12hの連続運転を行う"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ｴｰｼﾞﾝｸﾞ",
"検査表①:ﾌｧｰﾑﾊﾞｰｼﾞｮﾝの確認"
]
} | {
"QualityItem": "ｴｰｼﾞﾝｸﾞ動作",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "12時間:ｴﾗｰ停止が無いこと",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾚｲ完成品ﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2294",
"WorkName": "ﾌｧｰﾑﾊﾞｰｼﾞｮﾝ確認とｴｰｼﾞﾝｸﾞ実施",
"WorkItems": [
"2. ｴｰｼﾞﾝｸﾞの実施",
"1. ﾁｪｯｶｰ画面に表示されてあるﾌｧｰﾑﾊﾞｰｼﾞｮﾝを確認"
],
"WorkPoints": [
"ﾌｧｰﾑﾊﾞｰｼﾞｮﾝを記録する",
"ｴﾗｰ停止無い事",
"高速になっている事を確認",
"ﾁｪｯｶｰ画面で90ｻｲｸﾙを入力し12hの連続運転を行う"
],
"Tolks": [],
"InspectionNo": "WETE-G002-A11",
"InspectionItems": [
"検査表①:ｴｰｼﾞﾝｸﾞ"
],
"WorkTypes": [],
"Words": [
"検査表①:ﾌｧｰﾑﾊﾞｰｼﾞｮﾝの確認",
"WETE-G002-A11"
]
} | {
"QualityItem": "ﾊﾞｰｼﾞｮﾝ確認",
"ToolManageNo": "FM-2294",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾌｧｰﾑﾊﾞｰｼﾞｮﾝを記録",
"Method": "目視",
"RecordMethod": "WETE-G002-A11",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.