input stringclasses 1
value | instruction stringlengths 223 3.4k | output stringlengths 206 380 | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄﾀｲﾏｳﾝﾄ取付",
"WorkItems": [
"1. ①にCABLE-SUPPORT BOLT を取付"
],
"WorkPoints": [
"【取付方向】 略図を参照して下さい"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "38.9㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄｽﾄｯﾊﾟﾎﾞﾙﾄ取付",
"WorkItems": [
"1. ①にBOLT WASHER NUT を取付"
],
"WorkPoints": [
"調整 ㉗と㉘シックネスゲージ（0.1mm）にてボルト高さを調整 ※合算39mm確認 ㉗を設置させ㉙シックネスゲージ（0.2mm）が入ら無い事を確認",
"ｽﾄｯﾊﾟﾎﾞﾙﾄ出代 39mm±0.1mm"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"39±0.1mm以内"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄｽﾄｯﾊﾟﾎﾞﾙﾄ取付",
"WorkItems": [
"1. ①にBOLT WASHER NUT を取付"
],
"WorkPoints": [
"調整 ㉗と㉘シックネスゲージ（0.1mm）にてボルト高さを調整 ※合算39mm確認 ㉗を設置させ㉙シックネスゲージ（0.2mm）が入ら無い事を確認",
"ｽﾄｯﾊﾟﾎﾞﾙﾄ出代 39mm±0.1mm"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"39±0.1mm以内"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.2㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "2.0N･m",
"WorkName": "ﾍﾞｰｽﾌﾟﾚｰﾄｽﾄｯﾊﾟﾎﾞﾙﾄ取付",
"WorkItems": [
"1. ①にBOLT WASHER NUT を取付"
],
"WorkPoints": [
"調整 ㉗と㉘シックネスゲージ（0.1mm）にてボルト高さを調整 ※合算39mm確認 ㉗を設置させ㉙シックネスゲージ（0.2mm）が入ら無い事を確認",
"ｽﾄｯﾊﾟﾎﾞﾙﾄ出代 39mm±0.1mm"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": [
"39±0.1mm以内"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "ﾛｰﾄﾞｾﾙ組立①",
"WorkItems": [
"1. BLOCK にﾊﾞﾘ､打痕が無いことを確認",
"2. 1.完成品にCABLE-SUPPORT をBOLT にて取付",
"3. 2.完成品にSENSOR をBOLT WASHER WASHER にて取付"
],
"WorkPoints": [
"3か所取付"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "56cN･m",
"WorkName": "ﾛｰﾄﾞｾﾙ組立①",
"WorkItems": [
"1. BLOCK にﾊﾞﾘ､打痕が無いことを確認",
"2. 1.完成品にCABLE-SUPPORT をBOLT にて取付",
"3. 2.完成品にSENSOR をBOLT WASHER WASHER にて取付"
],
"WorkPoints": [
"3か所取付"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "56cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾛｰﾄﾞｾﾙ組立①",
"WorkItems": [
"4. 3.完成品のSENSOR の配線に指定寸法にてﾏｰｷﾝｸﾞ"
],
"WorkPoints": [
"ｾﾝｻｰﾎﾞﾃﾞｨより220mmでﾏｰｷﾝｸﾞ"
],
"Tolks": [
"締付ﾄﾙｸ 56cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法±1.0㎜以内",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾛｰﾄﾞｾﾙ組立②",
"WorkItems": [
"1. ①(ﾛｰﾄﾞｾﾙ貼付部分)とLOAD-CELL ﾛｰﾄﾞｾﾙの油分除去",
"▲4. 1完成品の青丸部分にLOAD-CELL ﾛｰﾄﾞｾﾙを接着",
"5. 各配線を結束",
"2. LOAD-CELL の検査成績書の添付を確認し､内容が銘板と一致することを確認",
"3. LOAD-CELL の型番を確認し､ｼﾘｱﾙ№を検査表に記入"
],
"WorkPoints": [
"【注意】 ﾛｰﾄﾞｾﾙ配線はﾌﾞﾛｯｸｺｰﾅｰに干渉しない様に､少し余裕を設ける",
"【注意】 ｲﾝｼｭﾛｯｸの頭の位置に指定あり ※この部分のみ位置指定あり",
"略図青丸部分",
"LOAD-CELL の配線は黄色矢印方向になる事 ※下写真参照",
"【注意】 押し付けるときは､中央部分は押さ無い事 ※下写真､緑丸部分は押さ無い事",
"【注意】 接着後､接着剤がはみ出無い事を確認",
"青丸部分の中央に㉗を塗布し、LOAD-CELL を接着 ※30秒ほどオレンジ部分を押し付ける"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表①:11.ﾊｰﾄﾞ検査",
"検査表①:11.ﾊｰﾄﾞ検査"
],
"WorkTypes": [
"▲特殊作業",
"■安全作業",
"●クリーン作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"【注意】緑色部分は押さない",
"ｵﾚﾝｼﾞ色部分を押す事",
"接着剤塗布 米粒:1",
"WEPJ-G002-C040"
]
} | {
"QualityItem": "検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "検査表の有無を確認する事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"安全工程",
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾛｰﾄﾞｾﾙ組立②",
"WorkItems": [
"1. ①(ﾛｰﾄﾞｾﾙ貼付部分)とLOAD-CELL ﾛｰﾄﾞｾﾙの油分除去",
"▲4. 1完成品の青丸部分にLOAD-CELL ﾛｰﾄﾞｾﾙを接着",
"5. 各配線を結束",
"2. LOAD-CELL の検査成績書の添付を確認し､内容が銘板と一致することを確認",
"3. LOAD-CELL の型番を確認し､ｼﾘｱﾙ№を検査表に記入"
],
"WorkPoints": [
"【注意】 ﾛｰﾄﾞｾﾙ配線はﾌﾞﾛｯｸｺｰﾅｰに干渉しない様に､少し余裕を設ける",
"【注意】 ｲﾝｼｭﾛｯｸの頭の位置に指定あり ※この部分のみ位置指定あり",
"略図青丸部分",
"LOAD-CELL の配線は黄色矢印方向になる事 ※下写真参照",
"【注意】 押し付けるときは､中央部分は押さ無い事 ※下写真､緑丸部分は押さ無い事",
"【注意】 接着後､接着剤がはみ出無い事を確認",
"青丸部分の中央に㉗を塗布し、LOAD-CELL を接着 ※30秒ほどオレンジ部分を押し付ける"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表①:11.ﾊｰﾄﾞ検査",
"検査表①:11.ﾊｰﾄﾞ検査"
],
"WorkTypes": [
"▲特殊作業",
"■安全作業",
"●クリーン作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"【注意】緑色部分は押さない",
"ｵﾚﾝｼﾞ色部分を押す事",
"接着剤塗布 米粒:1",
"WEPJ-G002-C040"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式を確認",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"安全工程",
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾛｯｸﾀｲﾄ",
"Size": "",
"ToolOther": "415",
"WorkName": "ﾛｰﾄﾞｾﾙ組立②",
"WorkItems": [],
"WorkPoints": [
"略図青丸部分"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:11.ﾊｰﾄﾞ検査",
"検査表①:11.ﾊｰﾄﾞ検査",
"接着剤塗布 米粒:1",
"▲特殊作業"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ415",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "1.5N･m",
"WorkName": "清掃部ｼﾘﾝﾀﾞ組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"全閉状態から3/4回転開けてﾛｯｸする",
"B105P"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "清掃部ｼﾘﾝﾀﾞ組立①",
"WorkItems": [
"1. AIR-SLIDE のｵｰﾄSWの止めねじをSCREW と交換し､仮取付",
"2. 1完成品にSPEED-CONTROLLER を取付",
"3. ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ調整"
],
"WorkPoints": [
"おおむね略図の位置に仮取付",
"仮止め:SD-A040344-056にて調整"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表AIR-SLIDE :ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ調整 (B,C)"
],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"全閉状態から3/4回転開けてﾛｯｸする",
"全閉状態から1回転開けてﾛｯｸする",
"B105P",
"WEPJ-G002-C040"
]
} | {
"QualityItem": "ｽﾋﾟｺﾝ調整",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り調整できている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "100cN･m",
"WorkName": "清掃部ｼﾘﾝﾀﾞ組立②",
"WorkItems": [
"1. ①にBRACKET を指定寸法にてBOLT で取付"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄはｼﾘﾝﾀﾞｰ端面に揃える ※緑線部分",
"㉘ジグを用いてシリンダー13.6mmの時に、ブラケット21.3mmに取付 ※略図参照"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"21.3±0.1㎜",
"13.6±0.1㎜"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾗｹｯﾄ位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5966",
"WorkName": "清掃部ｼﾘﾝﾀﾞ組立②",
"WorkItems": [
"1. ①にBRACKET を指定寸法にてBOLT で取付"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄはｼﾘﾝﾀﾞｰ端面に揃える ※緑線部分",
"㉘ジグを用いてシリンダー13.6mmの時に、ブラケット21.3mmに取付 ※略図参照"
],
"Tolks": [
"締付ﾄﾙｸ 100cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"21.3±0.1㎜",
"13.6±0.1㎜"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5966",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "清掃部ｼﾘﾝﾀﾞ組立②",
"WorkItems": [
"2. 取付寸法確認"
],
"WorkPoints": [
"1完成品の取付位置寸法を確認",
"取付位置寸法①:21.3㎜±0.1㎜",
"取付位置寸法BRACKET :13.6㎜±0.1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"治具使用例"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "指示寸法±0.1㎜以内",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "清掃部組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表①:ﾒｶﾆｶﾙﾁｪｯｸ"
],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"WEPJ-G002-C040"
]
} | {
"QualityItem": "ﾊﾞﾘ･打痕確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､打痕､傷などが無い事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "清掃部組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"検査表①:ﾒｶﾆｶﾙﾁｪｯｸ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "清掃部組立",
"WorkItems": [
"3. 隙間確認"
],
"WorkPoints": [
"Sﾋﾟﾝ当付け面の隙間を確認 ※青線部分",
"規格値:手で触れる部分に著しいﾊﾞﾘ･打痕無い事"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ部組立①",
"WorkItems": [
"3. 2完成品にCABLE-SUPPORT をBOLT にて取付"
],
"WorkPoints": [
"【取付目安】ﾀｲﾏｳﾝﾄ側面の延長線が板金ｺｰﾅｰ角部を向く様に取付"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ部組立②",
"WorkItems": [
"1. ①にMANIFOLD をBOLT WASHER にて取付",
"2. 1.完成品にSPEED-CONTROLLER をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "50cN･m",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ部組立②",
"WorkItems": [
"1. ①にMANIFOLD をBOLT WASHER にて取付",
"2. 1.完成品にSPEED-CONTROLLER をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾏﾆﾎｰﾙﾄﾞ部組立③",
"WorkItems": [
"1. ①のｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ調整"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表①:ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ調整 (A)"
],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"ｼｬｯﾀｰ(開)Bﾎﾟｰﾄ用 ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ 全閉状態から1回転開けてﾛｯｸする",
"ｼｬｯﾀｰ(閉)Aﾎﾟｰﾄ用 ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ 全閉状態から1回転開けてﾛｯｸする",
"WEPJ-G002-C040"
]
} | {
"QualityItem": "ｽﾋﾟｺﾝ調整",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り調整できている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "40cN･m",
"WorkName": "ｸﾗﾝﾌﾟ部ｹｰﾌﾞﾙ交換",
"WorkItems": [
"2. 取り外したら同じようにCABLE を接続"
],
"WorkPoints": [
"外したｶﾊﾞｰとﾎﾞﾙﾄはSD-A046151-112で使用"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝ圧入ｼﾞｸﾞ(φ3､2/φ3､4.5/φ3､7.5)",
"Size": "",
"ToolOther": "FM-6085",
"WorkName": "ｼｬｯﾀｰ部取付ﾌﾞﾛｯｸﾋﾟﾝ圧入",
"WorkItems": [
"1. BLOCK にﾊﾞﾘ､打痕が無いことを確認",
"2. 1完成品にPIN を2か所圧入"
],
"WorkPoints": [
"ﾋﾟﾝはﾃｰﾊﾟｰ側を圧入 ※略図青丸部分",
"ﾋﾟﾝ出代=2mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"出代2mm"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6085",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ組立①",
"WorkItems": [
"2. 1完成品にSPRING-PIN を圧入(3本)",
"1. PLATE のﾊﾞﾘ･打痕を確認",
"3. 2完成品にPIN を圧入"
],
"WorkPoints": [
"【注意】 Sﾋﾟﾝの割りの方向に注意 ※図参照",
"PIN ﾋﾟﾝの圧入方向※ﾃｰﾊﾟｰ側を飛び出しにする",
"ﾋﾟﾝ出代=3.0mm"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"WEPJ-G002-C040"
]
} | {
"QualityItem": "ﾊﾞﾘ･打痕確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､打痕､傷などが無い事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾋﾟﾝ圧入ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6099",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ組立①",
"WorkItems": [
"2. 1完成品にSPRING-PIN を圧入(3本)",
"1. PLATE のﾊﾞﾘ･打痕を確認"
],
"WorkPoints": [
"【注意】 Sﾋﾟﾝの割りの方向に注意 ※図参照"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "出代確認",
"ToolManageNo": "FM-6099",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ組立②",
"WorkItems": [
"1. BRACKET にﾊﾞﾘが無いことを確認",
"2. ①にBRACKET をBOLT にて取付"
],
"WorkPoints": [
"BRACKET は黄色矢印方向に押し当てにて取付",
"BRACKET は目視にて①と傾きなく取付"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"㉛治具"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "2.0N･m",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ組立②",
"WorkItems": [
"3. 2完成品にBOLT NUT WASHER を取付"
],
"WorkPoints": [
"BOLT ｽﾄｯﾊﾟﾎﾞﾙﾄ出代 38.7mm±0.1mm",
"調整 ㉛治具と㉜シックネスゲージ（0.1mm）にてボルト高さを調整 ※合算38.7mm確認 ㉛治具を設置させ㉜シックネスゲージ（0.2mm）が入ら無い事を確認"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"38.7mm±0.1mm",
"このﾎﾞﾙﾄ出代部分にて他機種ﾊﾟﾚｯﾄとの混載防止機能としている"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "2.0N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ組立②",
"WorkItems": [
"3. 2完成品にBOLT NUT WASHER を取付"
],
"WorkPoints": [
"BOLT ｽﾄｯﾊﾟﾎﾞﾙﾄ出代 38.7mm±0.1mm",
"調整 ㉛治具と㉜シックネスゲージ（0.1mm）にてボルト高さを調整 ※合算38.7mm確認 ㉛治具を設置させ㉜シックネスゲージ（0.2mm）が入ら無い事を確認"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"38.7mm±0.1mm",
"このﾎﾞﾙﾄ出代部分にて他機種ﾊﾟﾚｯﾄとの混載防止機能としている"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾎﾞﾙﾄ高さ調節ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6105",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ組立②",
"WorkItems": [
"3. 2完成品にBOLT NUT WASHER を取付"
],
"WorkPoints": [
"BOLT ｽﾄｯﾊﾟﾎﾞﾙﾄ出代 38.7mm±0.1mm",
"調整 ㉛治具と㉜シックネスゲージ（0.1mm）にてボルト高さを調整 ※合算38.7mm確認 ㉛治具を設置させ㉜シックネスゲージ（0.2mm）が入ら無い事を確認"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"38.7mm±0.1mm",
"このﾎﾞﾙﾄ出代部分にて他機種ﾊﾟﾚｯﾄとの混載防止機能としている"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6105",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ組立②",
"WorkItems": [
"3. 2完成品にBOLT NUT WASHER を取付"
],
"WorkPoints": [
"BOLT ｽﾄｯﾊﾟﾎﾞﾙﾄ出代 38.7mm±0.1mm",
"調整 ㉛治具と㉜シックネスゲージ（0.1mm）にてボルト高さを調整 ※合算38.7mm確認 ㉛治具を設置させ㉜シックネスゲージ（0.2mm）が入ら無い事を確認"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"38.7mm±0.1mm",
"このﾎﾞﾙﾄ出代部分にて他機種ﾊﾟﾚｯﾄとの混載防止機能としている"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ組立②",
"WorkItems": [
"3. 2完成品にBOLT NUT WASHER を取付"
],
"WorkPoints": [
"BOLT ｽﾄｯﾊﾟﾎﾞﾙﾄ出代 38.7mm±0.1mm",
"調整 ㉛治具と㉜シックネスゲージ（0.1mm）にてボルト高さを調整 ※合算38.7mm確認 ㉛治具を設置させ㉜シックネスゲージ（0.2mm）が入ら無い事を確認"
],
"Tolks": [
"締付ﾄﾙｸ 2.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"38.7mm±0.1mm",
"このﾎﾞﾙﾄ出代部分にて他機種ﾊﾟﾚｯﾄとの混載防止機能としている"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.2㎜が入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ組立③",
"WorkItems": [
"2. 1完成品にBRACKET をBOLT WASHER にて取付",
"1. BLOCK BRACKET にﾊﾞﾘ､打痕が無いことを確認",
"◆3. SPRING の両端にｸﾞﾘｰｽ塗布する"
],
"WorkPoints": [
"目視にてBLOCK と傾きなく取付"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"◆作業者安全作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程",
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ組立③",
"WorkItems": [
"2. 1完成品にBRACKET をBOLT WASHER にて取付",
"4. 2.完成品に､3.完成品をPIN にて取付",
"1. BLOCK BRACKET にﾊﾞﾘ､打痕が無いことを確認",
"◆3. SPRING の両端にｸﾞﾘｰｽ塗布する"
],
"WorkPoints": [
"目視にてBLOCK と傾きなく取付",
"【注意】 略図の方向から圧入",
"3.完成品を挿入してから圧入",
"SPRING ｽﾌﾟﾘﾝｸﾞのﾌｯｸ部分の向きに注意",
"PIN の溝部分にﾌｯｸを掛ける",
"PIN の向きは問わない",
"ｸﾞﾘｰｽ塗布箇所",
"PIN の圧入はBLOCK ﾂﾗｲﾁまで"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業",
"◆作業者安全作業"
],
"Words": [
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:各1"
]
} | {
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ組立④",
"WorkItems": [
"1. BLOCK にﾊﾞﾘ､打痕が無いことを確認",
"3. 2.完成品をPIN で取付",
"4. 可動部分の動作を確認する",
"2. ①のｽﾌﾟﾘﾝｸﾞをPIN でBLOCK に取付"
],
"WorkPoints": [
"【注意】 略図の方向から圧入",
"ｽﾌﾟﾘﾝｸﾞのﾌｯｸ部分をBLOCK に挿入後､PIN を圧入",
"PIN の溝部分にﾌｯｸを掛ける",
"【注意】 図の方向から圧入",
"PIN の圧入はBLOCK ﾂﾗｲﾁまで",
"PIN の圧入はBLOCK ﾂﾗｲﾁまで"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｽﾌﾟﾘﾝｸﾞ"
]
} | {
"QualityItem": "ﾊﾞﾘ･打痕確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､打痕､傷などが無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "保護ﾒｶﾞﾈ",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ組立⑤",
"WorkItems": [
"1. ①に②をBOLT にて取付"
],
"WorkPoints": [
"①の当てつけ面に隙間のない様に取付 ※下略図､青線部分"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄｸﾗﾝﾌﾟ組立⑤",
"WorkItems": [
"2. 当付け面の取付確認 ※略図青線部分"
],
"WorkPoints": [
"当付け面の隙間を確認 ※青線部分",
"規格値:0.03㎜が通ら無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "1.5N･m",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.27㎜",
"ToolOther": "10cN･m",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｵｰﾄSW 【B106】",
"ｵｰﾄSW 【B106】"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｵｰﾄSW位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4292",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｵｰﾄSW 【B106】",
"ｵｰﾄSW 【B106】"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4292",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ(共通)",
"Size": "",
"ToolOther": "FM-3418",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｵｰﾄSW 【B106】",
"ｵｰﾄSW 【B106】"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-3418",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "開閉限位置でONする事",
"Method": "PHﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ(2､8､11)",
"Size": "",
"ToolOther": "FM-6114",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立①",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"ｵｰﾄSW 【B106】",
"ｵｰﾄSW 【B106】"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "FM-6114",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "8㎜を挟み取付の事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立②",
"WorkItems": [
"1. ①配線の指定寸法にﾏｰｷﾝｸﾞ実施"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"220mm",
"【B106P】",
"130mm",
"【B104P】",
"160mm",
"80mm"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法±1.0㎜以内",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "63cN･m",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立③",
"WorkItems": [
"4. 2完成品BRACKET BRACKET の取付調整"
],
"WorkPoints": [
"以下の状態でBRACKET BRACKET を調整",
"シリンダーに㉘8㎜ブロックゲージを挟んだ状態で、エアーを供給【0.5Mpa】",
"BRACKET BRACKET で㉘11㎜ブロックゲージを挟んだ状態",
"BRACKET BRACKET とシリンダーの間に㉘2㎜ブロックゲージを挟んだ状態",
"【注意】 BRACKET BRACKET は取付穴左右ｾﾝﾀｰ狙いで取付"
],
"Tolks": [
"締付ﾄﾙｸ 63cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"2㎜ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"8㎜ﾌﾞﾛｯｸｹﾞｰｼﾞ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "63cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ(2､8､11)",
"Size": "",
"ToolOther": "FM-6114",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立③",
"WorkItems": [
"4. 2完成品BRACKET BRACKET の取付調整"
],
"WorkPoints": [
"以下の状態でBRACKET BRACKET を調整",
"シリンダーに㉘8㎜ブロックゲージを挟んだ状態で、エアーを供給【0.5Mpa】",
"BRACKET BRACKET で㉘11㎜ブロックゲージを挟んだ状態",
"BRACKET BRACKET とシリンダーの間に㉘2㎜ブロックゲージを挟んだ状態",
"【注意】 BRACKET BRACKET は取付穴左右ｾﾝﾀｰ狙いで取付"
],
"Tolks": [
"締付ﾄﾙｸ 63cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"2㎜ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"8㎜ﾌﾞﾛｯｸｹﾞｰｼﾞ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-6114",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "各2・8・11㎜を挟み取付の事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｵｰﾄSW位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4292",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立③",
"WorkItems": [
"1. BRACKET BRACKET のﾊﾞﾘ､打痕を確認",
"2. ①にBRACKET BRACKET をBOLT にて仮取付",
"3. ㉙エアー供給ユニットを接続",
"4. 2完成品BRACKET BRACKET の取付調整"
],
"WorkPoints": [
"青色矢印部分に接続 ※ｴｱｰはまだ供給しない",
"以下の状態でBRACKET BRACKET を調整",
"シリンダーに㉘8㎜ブロックゲージを挟んだ状態で、エアーを供給【0.5Mpa】",
"BRACKET BRACKET で㉘11㎜ブロックゲージを挟んだ状態",
"BRACKET BRACKET とシリンダーの間に㉘2㎜ブロックゲージを挟んだ状態",
"【注意】 BRACKET BRACKET は取付穴左右ｾﾝﾀｰ狙いで取付"
],
"Tolks": [
"締付ﾄﾙｸ 63cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"2㎜ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"8㎜ﾌﾞﾛｯｸｹﾞｰｼﾞ"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4292",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立④",
"WorkItems": [
"1. ①にCABLE-SUPPORT BOLT を2か所取付",
"2. 1完成品の配線を結束"
],
"WorkPoints": [
"緑丸部は1本で結束の事",
"黄丸部のﾏｰｷﾝｸﾞが揃っていることを確認後､結束",
"ｲﾝｼｭﾛｯｸから90mmのﾏｰｷﾝｸﾞが揃っている事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ｼｬｯﾀｰ部ｼﾘﾝﾀﾞ組立④",
"WorkItems": [
"1. ①にCABLE-SUPPORT BOLT を2か所取付",
"2. 1完成品の配線を結束"
],
"WorkPoints": [
"緑丸部は1本で結束の事",
"黄丸部のﾏｰｷﾝｸﾞが揃っていることを確認後､結束",
"ｲﾝｼｭﾛｯｸから90mmのﾏｰｷﾝｸﾞが揃っている事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法±1.0㎜以内",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "1.5N･m",
"WorkName": "ﾌﾟﾚｰﾄ部ｼﾘﾝﾀﾞ組立①",
"WorkItems": [],
"WorkPoints": [
"仮止め:SD-A040344-038にて調整"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"検査表AIR-SLIDE :ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ調整 (D,E)"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ部ｼﾘﾝﾀﾞ組立①",
"WorkItems": [
"1. AIR-SLIDE のｵｰﾄSWのﾄﾒﾈｼﾞをSCREW と交換する ※2か所",
"2. おおむね略図の位置にｵｰﾄSWを仮取付",
"3. 2完成品にSPEED-CONTROLLER を2か所取付",
"4. SPEED-CONTROLLER ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ調整"
],
"WorkPoints": [
"仮止め:SD-A040344-038にて調整"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表AIR-SLIDE :ｽﾋﾟｰﾄﾞｺﾝﾄﾛｰﾗｰ調整 (D,E)"
],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"B102P",
"B103P",
"全閉状態から1.5回転開けてﾛｯｸする",
"全閉状態から1回転開けてﾛｯｸする",
"WEPJ-G002-C040"
]
} | {
"QualityItem": "ｽﾋﾟｺﾝ調整",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り調整できている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "ﾌﾟﾚｰﾄ部ｼﾘﾝﾀﾞ組立②",
"WorkItems": [
"1. ①にBRACKET をBOLT にて取付"
],
"WorkPoints": [
"取付寸法=略図参照",
"①とBRACKET の端面を揃える"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"37.1mm±0.1mm",
"ｴｱｽﾗｲﾄﾞとﾌﾞﾗｹｯﾄの端面を揃える",
"治具使用例"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｴｱｽﾗｲﾄﾞ組立ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5980",
"WorkName": "ﾌﾟﾚｰﾄ部ｼﾘﾝﾀﾞ組立②",
"WorkItems": [
"1. ①にBRACKET をBOLT にて取付"
],
"WorkPoints": [
"取付寸法=略図参照",
"①とBRACKET の端面を揃える"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": [
"37.1mm±0.1mm",
"ｴｱｽﾗｲﾄﾞとﾌﾞﾗｹｯﾄの端面を揃える",
"治具使用例"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-5980",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾟﾚｰﾄ部ｼﾘﾝﾀﾞ組立②",
"WorkItems": [
"2. 取付寸法確認"
],
"WorkPoints": [
"1完成品の取付位置寸法を確認",
"取付位置寸法:37.1㎜±0.1㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"◆作業者安全作業"
],
"Words": []
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "指定寸法±0.1㎜以内",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"作業者安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾛｯｸﾀｲﾄ",
"Size": "",
"ToolOther": "243",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部ﾌﾟﾚｰﾄ組立",
"WorkItems": [
"1. PLATE にﾊﾞﾘ､打痕が無いことを確認する",
"3. SCREW の出代を調整する",
"▲2. SCREW に㉘塗布後、PLATE に取付"
],
"WorkPoints": [
"SCREW をねじ込み､板裏出代1mm±0.1mmに取付",
"4箇所"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"1mm±0.1mm",
"接着剤塗布 ｺﾞﾏ粒:各1",
"▲特殊作業"
]
} | {
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Other": "ﾛｯｸﾀｲﾄ243",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部ﾌﾟﾚｰﾄ組立",
"WorkItems": [
"1. PLATE にﾊﾞﾘ､打痕が無いことを確認する",
"3. SCREW の出代を調整する",
"▲2. SCREW に㉘塗布後、PLATE に取付"
],
"WorkPoints": [
"SCREW をねじ込み､板裏出代1mm±0.1mmに取付",
"4箇所"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"1mm±0.1mm",
"接着剤塗布 ｺﾞﾏ粒:各1",
"▲特殊作業"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立①",
"WorkItems": [
"1. ①に②をBOLT にて取付"
],
"WorkPoints": [
"Sﾋﾟﾝ(3点)との間に隙間のない様に取付"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立①",
"WorkItems": [
"2. 隙間､及び干渉確認 ※略図青線部分"
],
"WorkPoints": [
"Sﾋﾟﾝ当付け面の隙間を確認 ※青線部分",
"【目視確認】 ﾌﾞﾗｹｯﾄU溝部分とﾎﾞﾙﾄの干渉が無い事",
"各隙間 0.03mmが通ら無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"必要部分のみ描いています"
]
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立②",
"WorkItems": [
"1. ①に②をBOLT にて取付"
],
"WorkPoints": [
"②上辺に隙間のない様に取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立②",
"WorkItems": [
"2. 取付確認 ※略図青線部分"
],
"WorkPoints": [
"当付け面の隙間を確認 ※青線部分",
"各隙間 0.03㎜が通ら無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "63cN･m",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立③",
"WorkItems": [
"1. ①に②を付属ﾎﾞﾙﾄにて取付"
],
"WorkPoints": [
"②の取付穴はｼﾘﾝﾀﾞｰを開状態にすると現れる ※黄色矢印方向",
"②は①の基準ﾋﾟﾝに嵌合させて取付",
"付属ﾎﾞﾙﾄ M3×20 2本"
],
"Tolks": [
"締付ﾄﾙｸ 63cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "63cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立④",
"WorkItems": [
"1. ①に②をBOLT にて仮取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"仮止め:SD-A046151-106にて本締め"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｵｰﾄSW位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4292",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立⑤",
"WorkItems": [
"1. ①のｵｰﾄSW調整"
],
"WorkPoints": [
"点灯した位置でﾏｰｷﾝｸﾞ",
"消灯した位置でﾏｰｷﾝｸﾞ",
"ﾏｰｷﾝｸﾞ中央に取付",
"㉖エアー供給ユニットより、青色矢印側にエアを供給 【0.5Mpa】",
"青丸部分のSWを調整",
"㉖エアー供給ユニットより、黄色矢印側にエアを供給 【0.5Mpa】",
"黄丸部分のSWを調整"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"ｵｰﾄSW取付の合わせ方",
"戻り限調整",
"行き限調整"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4292",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "PHﾁｪｯｶｰ(共通)",
"Size": "",
"ToolOther": "FM-3418",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立⑤",
"WorkItems": [
"1. ①のｵｰﾄSW調整"
],
"WorkPoints": [
"点灯した位置でﾏｰｷﾝｸﾞ",
"消灯した位置でﾏｰｷﾝｸﾞ",
"ﾏｰｷﾝｸﾞ中央に取付",
"㉖エアー供給ユニットより、青色矢印側にエアを供給 【0.5Mpa】",
"青丸部分のSWを調整",
"㉖エアー供給ユニットより、黄色矢印側にエアを供給 【0.5Mpa】",
"黄丸部分のSWを調整"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"ｵｰﾄSW取付の合わせ方",
"戻り限調整",
"行き限調整"
]
} | {
"QualityItem": "動作確認",
"ToolManageNo": "FM-3418",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "開閉限位置でONする事",
"Method": "PHﾁｪｯｶｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.27㎜",
"ToolOther": "10cN･m",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立⑤",
"WorkItems": [
"1. ①のｵｰﾄSW調整"
],
"WorkPoints": [
"点灯した位置でﾏｰｷﾝｸﾞ",
"消灯した位置でﾏｰｷﾝｸﾞ",
"ﾏｰｷﾝｸﾞ中央に取付",
"㉖エアー供給ユニットより、青色矢印側にエアを供給 【0.5Mpa】",
"青丸部分のSWを調整",
"㉖エアー供給ユニットより、黄色矢印側にエアを供給 【0.5Mpa】",
"黄丸部分のSWを調整"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"ｵｰﾄSW取付の合わせ方",
"戻り限調整",
"行き限調整"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾉｽﾞﾙﾎﾙﾀﾞｰ部組立⑥",
"WorkItems": [
"1. ①のｵｰﾄSW配線にﾏｰｷﾝｸﾞ実施"
],
"WorkPoints": [
"指定寸法にてﾏｰｷﾝｸﾞ実施 ※略図参照"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"90mm",
"100mm",
"B103P",
"B102P"
]
} | {
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法±1.0㎜以内",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾞﾛｯｸ(A013)ﾋﾟﾝ圧入",
"WorkItems": [
"1. BLOCK にPIN (4個)を打ち込む"
],
"WorkPoints": [
"座ぐり面を下にする",
"圧入方向に注意(割りの向き)",
"圧入方向に注意(割りの向き)",
"圧入時BLOCK の方向に注意",
"出代5mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"5㎜"
]
} | {
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法±0.5㎜以内",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "中継ﾎﾞｰﾄﾞ用ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.5㎜BOX",
"ToolOther": "120cN･m",
"WorkName": "中継ﾎﾞｰﾄﾞ用ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [
"3. 2完成品にSPACER WASHER を取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 110cN･m",
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": [
"15㎜"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "中継ﾎﾞｰﾄﾞ用ﾌﾞﾗｹｯﾄ組立",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"▲特殊作業",
"●クリーン作業"
],
"Words": []
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"特殊工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "中継ﾎﾞｰﾄﾞ部組立",
"WorkItems": [
"■1. HOT SWAP RELAY BOARD の検査成績書の添付を確認し､検査日､入荷日､判定を記入",
"■★2. HOT SWAP RELAY BOARD の型番を確認し､ｼﾘｱﾙ№を検査表に記入",
"★3. ①にHOT SWAP RELAY BOARD をBOLT WASHER (各4個)で取付"
],
"WorkPoints": [
"ｼﾘｱﾙﾗﾍﾞﾙの位置",
"HOT SWAP RELAY BOARD の取付方向は下図のｼﾘｱﾙﾗﾍﾞﾙの位置の通り取付こと"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表①:安全部品 検査",
"検査表①:安全部品 検査"
],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"WEPJ-G002-C040"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式を確認",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "中継ﾎﾞｰﾄﾞ部組立",
"WorkItems": [
"■1. HOT SWAP RELAY BOARD の検査成績書の添付を確認し､検査日､入荷日､判定を記入",
"■★2. HOT SWAP RELAY BOARD の型番を確認し､ｼﾘｱﾙ№を検査表に記入",
"★3. ①にHOT SWAP RELAY BOARD をBOLT WASHER (各4個)で取付"
],
"WorkPoints": [
"ｼﾘｱﾙﾗﾍﾞﾙの位置",
"HOT SWAP RELAY BOARD の取付方向は下図のｼﾘｱﾙﾗﾍﾞﾙの位置の通り取付こと"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表①:安全部品 検査",
"検査表①:安全部品 検査"
],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"WEPJ-G002-C040"
]
} | {
"QualityItem": "検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "検査表の有無を確認する事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "80cN･m",
"WorkName": "中継ﾎﾞｰﾄﾞ部組立",
"WorkItems": [
"■1. HOT SWAP RELAY BOARD の検査成績書の添付を確認し､検査日､入荷日､判定を記入",
"■★2. HOT SWAP RELAY BOARD の型番を確認し､ｼﾘｱﾙ№を検査表に記入",
"★3. ①にHOT SWAP RELAY BOARD をBOLT WASHER (各4個)で取付"
],
"WorkPoints": [
"ｼﾘｱﾙﾗﾍﾞﾙの位置",
"HOT SWAP RELAY BOARD の取付方向は下図のｼﾘｱﾙﾗﾍﾞﾙの位置の通り取付こと"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"検査表①:安全部品 検査",
"検査表①:安全部品 検査",
"■安全作業",
"★静電対策作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "1.5N･m",
"WorkName": "ﾕﾆｯﾄﾛｯｸ部ｼﾘﾝﾀﾞ組立",
"WorkItems": [
"1. CYLINDER にJOINT (2個)を取付",
"2. CYLINDER のｵｰﾄｽｲｯﾁのすりわり付き止めねじとSCREW を交換し行き限でｾﾝｻｰ位置調整すること"
],
"WorkPoints": [
"ｵｰﾄSW位置調整は､治具を接続しｼﾘﾝﾀﾞｰｼｬﾌﾄが行き限の状態でSWのLEDが点灯している事",
"CYLINDER の付属ﾎﾞﾙﾄはSD-A046151-043で使用"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.27㎜",
"ToolOther": "10cN･m",
"WorkName": "ﾕﾆｯﾄﾛｯｸ部ｼﾘﾝﾀﾞ組立",
"WorkItems": [],
"WorkPoints": [
"点灯した位置でﾏｰｷﾝｸﾞ",
"消灯した位置でﾏｰｷﾝｸﾞ",
"ﾏｰｷﾝｸﾞ中央に取付"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｵｰﾄSW取付の合わせ方"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｵｰﾄSW位置調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-4292",
"WorkName": "ﾕﾆｯﾄﾛｯｸ部ｼﾘﾝﾀﾞ組立",
"WorkItems": [],
"WorkPoints": [
"点灯した位置でﾏｰｷﾝｸﾞ",
"消灯した位置でﾏｰｷﾝｸﾞ",
"ﾏｰｷﾝｸﾞ中央に取付"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｵｰﾄSW取付の合わせ方"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4292",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾝﾄﾞﾙ部組立",
"WorkItems": [
"1. GRIP にLEVER を素手でねじ込む"
],
"WorkPoints": [
"LEVER の短いほうをGRIP に取付",
"ﾈｼﾞ緩みの無いこと"
],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表GRIP :ﾒｶﾆｶﾙﾁｪｯｸ"
],
"WorkTypes": [],
"Words": [
"WEPJ-G002-C040"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾀｲﾏｳﾝﾄ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾀｲﾏｳﾝﾄ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｱﾙｶﾝｻｽ",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾀｲﾏｳﾝﾄ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"WEPJ-G002-C040"
]
} | {
"QualityItem": "ﾊﾞﾘ･打痕確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､打痕､傷などが無い事",
"Method": "ｱﾙｶﾝｻｽ",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾀｲﾏｳﾝﾄ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.5㎜BOX",
"ToolOther": "120cN･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄｽﾍﾟｰｻｰ取付",
"WorkItems": [
"1. SPACER WASHER を②に取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 120cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "120cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾌﾞﾛｯｸ取付",
"WorkItems": [
"2. ⑥に1完成品をBOLT ･COLLAR BOLT で取付",
"1. 下図のようにBLOCK ､②にPLATE (2個)とCOLLAR (4個)をｾｯﾄ"
],
"WorkPoints": [
"･PLATE の凸の向きをBLOCK ②側にすること",
"下図BLOCK ②の左側ﾋﾟﾝにPLATE の青丸部を挿入"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. BRACKET にBRACKET をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では同じものを2個製作"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"3. ④に1.完成品と2.完成品をBOLT WASHER で取付"
],
"WorkPoints": [
"㉙ﾊﾝﾄﾞﾙ取付位置調整治具にて取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"2.完成品"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾊﾝﾄﾞﾙ取付位置調整治具",
"Size": "",
"ToolOther": "FM-4272",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"3. ④に1.完成品と2.完成品をBOLT WASHER で取付"
],
"WorkPoints": [
"㉙ﾊﾝﾄﾞﾙ取付位置調整治具にて取付"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"1.完成品",
"2.完成品"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "FM-4272",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"2. 1.完成品にBUSH を貼付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"この作業では1個のみ",
"15㎜"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指定寸法±1.0㎜以内",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄｼﾘﾝﾀﾞ取付",
"WorkItems": [
"1. ①を②に①付属のﾎﾞﾙﾄとWASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"付属ﾎﾞﾙﾄ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾊﾝﾄﾞﾙ取付",
"WorkItems": [
"1. ①に②をWASHER NUT NUT で取付"
],
"WorkPoints": [
"ﾈｼﾞ緩みの無いこと"
],
"Tolks": [
"締付ﾄﾙｸ 5.5N･m",
"締付ﾄﾙｸ 6N･m"
],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表①:ﾒｶﾆｶﾙﾁｪｯｸ"
],
"WorkTypes": [],
"Words": [
"WEPJ-G002-C040"
]
} | {
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "緩み無い事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "5.5N･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾊﾝﾄﾞﾙ取付",
"WorkItems": [
"1. ①に②をWASHER NUT NUT で取付"
],
"WorkPoints": [
"ﾈｼﾞ緩みの無いこと"
],
"Tolks": [
"締付ﾄﾙｸ 5.5N･m",
"締付ﾄﾙｸ 6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾒｶﾆｶﾙﾁｪｯｸ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "5.5N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "10㎜",
"ToolOther": "6N･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄﾊﾝﾄﾞﾙ取付",
"WorkItems": [
"1. ①に②をWASHER NUT NUT で取付"
],
"WorkPoints": [
"ﾈｼﾞ緩みの無いこと"
],
"Tolks": [
"締付ﾄﾙｸ 5.5N･m",
"締付ﾄﾙｸ 6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"検査表①:ﾒｶﾆｶﾙﾁｪｯｸ"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄ制御ﾎﾞｰﾄﾞ取付",
"WorkItems": [
"★3. ②にHEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) をSPACER BOLT WASHER WASHER で取付",
"■1. HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の検査成績書の添付を確認し､検査日､入荷日､判定を検査表に記載",
"■★2. HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の品番､型番を確認し､ｼﾘｱﾙ№を検査表に記入"
],
"WorkPoints": [
"HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の基板の取付方向に注意する",
"このｺﾈｸﾀｰをﾊﾝﾄﾞﾙ側に向ける",
"このｺﾈｸﾀｰを前側に向ける"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表SPACER :安全部品 検査",
"検査表SPACER :安全部品 検査"
],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"WEPJ-G002-C040"
]
} | {
"QualityItem": "型式確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式を確認",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄ制御ﾎﾞｰﾄﾞ取付",
"WorkItems": [
"★3. ②にHEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) をSPACER BOLT WASHER WASHER で取付",
"■1. HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の検査成績書の添付を確認し､検査日､入荷日､判定を検査表に記載",
"■★2. HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の品番､型番を確認し､ｼﾘｱﾙ№を検査表に記入"
],
"WorkPoints": [
"HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の基板の取付方向に注意する",
"このｺﾈｸﾀｰをﾊﾝﾄﾞﾙ側に向ける",
"このｺﾈｸﾀｰを前側に向ける"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "WEPJ-G002-C040",
"InspectionItems": [
"検査表SPACER :安全部品 検査",
"検査表SPACER :安全部品 検査"
],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"WEPJ-G002-C040"
]
} | {
"QualityItem": "検査表確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "検査表の有無を確認する事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C040",
"Other": "-",
"ProcessNames": [
"安全工程",
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "5.5㎜BOX",
"ToolOther": "95cN･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄ制御ﾎﾞｰﾄﾞ取付",
"WorkItems": [
"★3. ②にHEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) をSPACER BOLT WASHER WASHER で取付",
"■1. HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の検査成績書の添付を確認し､検査日､入荷日､判定を検査表に記載",
"■★2. HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の品番､型番を確認し､ｼﾘｱﾙ№を検査表に記入"
],
"WorkPoints": [
"HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の基板の取付方向に注意する",
"このｺﾈｸﾀｰをﾊﾝﾄﾞﾙ側に向ける",
"このｺﾈｸﾀｰを前側に向ける"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"検査表SPACER :安全部品 検査",
"検査表SPACER :安全部品 検査",
"■安全作業",
"★静電対策作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "80cN･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄ制御ﾎﾞｰﾄﾞ取付",
"WorkItems": [
"★3. ②にHEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) をSPACER BOLT WASHER WASHER で取付",
"■1. HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の検査成績書の添付を確認し､検査日､入荷日､判定を検査表に記載",
"■★2. HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の品番､型番を確認し､ｼﾘｱﾙ№を検査表に記入"
],
"WorkPoints": [
"HEAD MAINTAINANCE UNIT CONTROL BOARD(FOR FC HEAD) の基板の取付方向に注意する",
"このｺﾈｸﾀｰをﾊﾝﾄﾞﾙ側に向ける",
"このｺﾈｸﾀｰを前側に向ける"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"■安全作業",
"★静電対策作業"
],
"Words": [
"検査表SPACER :安全部品 検査",
"検査表SPACER :安全部品 検査",
"■安全作業",
"★静電対策作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程",
"安全工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "80cN･m",
"WorkName": "ｻﾌﾞﾌﾟﾚｰﾄ中継ﾎﾞｰﾄﾞ部取付",
"WorkItems": [
"★1. ①に②をBOLT WASHER で取付"
],
"WorkPoints": [
"ｹｰﾌﾞﾙｻﾎﾟｰﾄの位置",
"取付方向に注意"
],
"Tolks": [
"締付ﾄﾙｸ 80cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [
"★静電対策作業"
],
"Words": [
"★静電対策作業"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "80cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"静電対策工程"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾛｰﾄﾞｾﾙ取付",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "ﾛｰﾄﾞｾﾙ取付",
"WorkItems": [
"1. ①に②をBOLT にて取付",
"2. 隙間確認"
],
"WorkPoints": [
"ﾋﾟﾝと段差に当てつけて取付",
"Sﾋﾟﾝ当付け面の隙間を確認 ※青線部分",
"段差の隙間を確認 ※黄色矢印部分が段差隙間部分",
"各隙間 0.03mmのｼｯｸﾈｽｹﾞｰｼﾞが通らないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "清掃部取付",
"WorkItems": [
"1. ①に②をBOLT にて取付",
"2. 隙間確認"
],
"WorkPoints": [
"Sﾋﾟﾝ当付け面の隙間を確認 ※青線部分",
"ﾋﾟﾝに当付けて取付",
"各隙間 0.03mmのｼｯｸﾈｽｹﾞｰｼﾞが通らないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.03㎜",
"ToolOther": "",
"WorkName": "清掃部取付",
"WorkItems": [
"1. ①に②をBOLT にて取付",
"2. 隙間確認"
],
"WorkPoints": [
"Sﾋﾟﾝ当付け面の隙間を確認 ※青線部分",
"ﾋﾟﾝに当付けて取付",
"各隙間 0.03mmのｼｯｸﾈｽｹﾞｰｼﾞが通らないこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": []
} | {
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.03㎜が通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null | |
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.27㎜",
"ToolOther": "10cN･m",
"WorkName": "清掃部ｵｰﾄSW調整",
"WorkItems": [
"1. ①のｵｰﾄSW調整"
],
"WorkPoints": [
"点灯した位置でﾏｰｷﾝｸﾞ",
"消灯した位置でﾏｰｷﾝｸﾞ",
"㉘エアー供給ユニットより、戻り側接手にエアーを供給 ※青色矢印",
"ｴｱｰ供給圧【0.5Mpa】"
],
"Tolks": [
"締付ﾄﾙｸ 10cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"WorkTypes": [],
"Words": [
"ｵｰﾄSW取付の合わせ方"
]
} | {
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "10cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessNames": [
"-"
]
} | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.