Project Requirements - Design Professional - Manufacturing - Buildings

Buildings


Design ProfessionalsConstruction ProfessionalsLicensingbuilding UP

Project Guidelines for Design Professionals
Engineers (PE) & Architects (RA)
Local Law 108/2019

Project Guidelines for Design Professionals

Engineers (PE) & Architects (RA)

Local Law 108/2019


Design Professional Requirements: Manufacturing

Applicability of Code and Zoning

An existing building renovation project could be filed under either the current Codes, the 2014 NYC Construction Codes (Administrative, Building, Plumbing, Fuel Gas and Mechanical Codes), or under Prior Codes, such as the 1968 Code, 1938 Code or earlier Codes, depending on the age of the existing building; reference Administrative Code (AC) section 28-101.2.

However, there are exceptions if Prior Codes are used, per AC 28-101.4.3. For example, the 2014 Code must be used for accessibility requirements, certain renovation work of mechanical, plumbing, sprinkler, fire protection and/or fuel gas systems, specific building elements such as security grilles, handrails, guards, roofs, etc., and certain kinds of structural work.

Flood Plains, BC Appendix G, must be considered when performing renovations.

Renovation work must comply also with the current NYC Energy Conservation Code and applicable Local Laws, Rules and regulations as well as other project requirements.

When required by the project scope of work the renovation must also comply with the rules, regulations, laws and Codes of other City agencies, such as the NYC Fire Department (FDNY), NYC Environmental Protection (DEP), NYC Transportation (DOT), NYC Landmarks Commission, NYS Department of Environmental Conservation, and others.

*Note: While the following is a list of key zoning, Code and other regulations that may be relevant in the project design, it is not comprehensive.*

Codes

Project Element

Applicable Code and Regulations

Current Code*

Prior Codes

2014

1968

1938 Building Code, MDL & HMC

Administrative

2014 AC 28-101.4.5 and Administrative Code

2014 AC 28-101.4.3 -Optional Use of 1968 Code and AC 28-101.4.5

2014 AC 28-101.4.3, AC 28-101.4.5 and 1968 AC 27-114

Accessibility

2014 BC Chapter 11, and BC Appendix E, BC Appendix N, and BC Appendix P

Building Heights & Areas

BC Chapter 5

AC 27-293 through AC 27-315

Article 5

Construction Types

BC Chapter 6

AC 27-269 through AC 27-287

Article 4

Egress

BC Chapter 10
BC Appendix S

AC 27-354 through AC 27-396.6

Article 7

Elevators

2014 BC Chapter 30 and BC Appendix K

Fire Protection

BC Chapter 9 and Appendix Q

2014 AC 28-315.2, 2014 BC Chapter 9 and Appendix Q

Flood Resistant Construction

2014 BC Appendix G

Interior Environment

BC Chapter 12, BC Appendix R, and MC Chapters 4 through 6

AC 27-725 through AC 27-770

1938 BC Article 6, 1938 Article 12 and 1938 Article 15, Articles 15

Materials

BC Chapters 19 to 26

Subject to applicable provisions of the 2014 BC and
1968 AC 27-600 through AC 27-651

Subject to applicable provisions of the 2014 BC, and 1938 BC Article 8 and Article 19

Roof Assemblies and Rooftop Structures

Chapter 15

Subject to applicable provisions of the 2014 BC and 1968 BC 27-338

Subject to applicable provisions of the 2014 BC and 1938 BC Article 11

Safeguards During Construction

2014 BC Chapter 33

Structural, Soils and Foundation

BC Chapter 16 and 18

2014 BC 1601.2 and
1968 AC 27-580 through AC 27-724

2014 BC 1601.2 and 1938 BC Article 9

Use and Occupancy Classification

BC Chapter 3

AC 27-234 through AC 27-268

Article 4 and Article 13

Other Guidelines

Antennas

See Renovation Antenna Guidelines

Boiler

See Building Systems Boiler Guidelines

Building Pavement Plan

See BPP - Alteration Project Guideline

Construction Equipment

See Construction Equipment Guidelines (Scaffold, Hoists, Chutes, Fences, Sidewalk Sheds, Mechanical Construction Equipment)

Curb Cut

See Renovation Curb Cut Guidelines

Deck/Porch/Swimming Pool

See Deck/Porch/Swimming Pool Guidelines

Emergency Power Systems

See Building Systems Emergency Power Guidelines

Public Right-of-Way Encroachments

See Renovations Public Right-of-way Encroachment Guidelines

Shoring/Underpinning of Foundation/Retaining Wall/Flag Pole/Sign Ground Structures

See Renovation Shoring, Underpinning of Foundation, Retaining Wall, Flag Pole, Signs and Ground Structures Guidelines

Mechanical

See Building Systems Mechanical Guidelines

Plumbing

See Building Systems Plumbing Guidelines

Signs

See Renovations Sign Guidelines

Solar Panels

See Building Systems Solar Guidelines

Sprinkler

See Building Systems Sprinkler Guidelines

Standpipe

See Building Systems Standpipe Guidelines

Zoning

Manufacturing renovation projects may require compliance with the following Zoning Resolution sections:

Special and Sub-district Provisions – ZR Articles 8-13

E Designations (environmental considerations) – ZR 11-15, ZR Appendix C Table 1 and Table 2

Permitted obstructions in required open space, yards, setbacks, and height – ZR – Article 3 and Article 4

Performance Standards & Controls – ZR 42-20

Parking and Loading Regulations – ZR 44-00 and subsections

Flood Hazard Areas – Raising and moving of existing building within same zoning lot, ZR 64-00

Other Regulation(s) for Reference

Buildings Bulletin

BB 2008-001 – Accessory Spaces Under 10% per Story

BB 2008-003 – Mezzanine Floor Area Exemptions for Building Code

BB 2008-009 – Incidental Use Areas and Accessory Occupancies

BB 2009-005 – Exterior Exhaust Exemption for Electric Clothes Dryers

BB 2009-012 – Work in Tidal Wetlands and Coastal Erosion Hazard Areas

BB 2009-023 – Smoke Detectors in Elevator Lobbies and Machine Rooms

BB 2014-026 – Little (e) Designations/Environmental Restrictive Declarations

BB 2015-008 – Easements and Restrictive Declarations

BB 2015-017 – Opening in the Exterior Wall/Lot Line Windows

BB 2016-003 – Grease duct installation and testing

TPPN

TPPN 10/88 – Construction Adjacent to Historic Structures

TPPN 02/91 – Solid Waste Transfer Stations

TPPN 13/93 – Day Care Facilities Accessory to Manufacturing Facilities

TPPN 02/96 – Side Yard Requirements for Building Separation

TPPN 1/06 – Outlines the requirements for accessory bathroom and kitchen facilities in connection with manufacturing use.

Guidelines for Submission of Renovation Project Plans

Prior to preparing the design documents and construction drawings, the Registered Design Professional must perform a pre-design review that analyzes all of the existing building elements, systems and other components affected by the proposed scope of work, to verify a code compliant renovation of the building. Based upon the complexity and scale of the project, the information provided on the drawings must clearly describe all of the work required for the code compliant execution and completion of the project per AC Article 104 or 2014 BC 107.2.

The Department’s guidelines, outlined below, provide an organized approach for the preparation of construction documents; this will facilitate the plan review process. Drawings shall clearly indicate existing condition, proposed condition and any area affected by the scope of work.

Complete Submission of Construction Documents

Construction drawings should represent complete work, including multiple disciplines such as architectural, structural, plumbing, electrical, mechanical, and others. There must be close coordination between all disciplines for the proposed scope of work to ensure code compliance; reference AC 28-104.7 and BC 107.2.

A complete submission of drawings should include:

Construction Documents. Drawings necessary to convey essential information such as floor layouts, elevations, schedules and details. The applicable Building Codes and notes should be stated on the drawings as required to demonstrate Code and zoning compliance. Where essential to clarify overall layouts and details, a scale should be included on the drawings; a graphic scale is recommended.

Title Sheet. Should clearly describe the project location, including the adjacent streets, properties, etc. and a graphical scale. Drawing notes should include building occupancy classification, zoning use group, construction classification, the project’s scope, and the building’s primary structural system.

Drawing Index. Recommended to clearly identify all the information that may be involved.

Site/Plot Plan. Clearly show the size and location of the lot, show all existing structures on the zoning lot, and include all dimensions and other relevant information such as streets, adjacent buildings, curb cuts, north arrow, etc. The area of proposed work shall be clearly identified.

Floor Plans. Show existing and proposed conditions; clearly identify rooms’ names and use them consistently between the different discipline drawings. Coordinate between all trades / disciplines to ensure that the proposed scope of work is complete and shown on all submitted discipline drawings. Where required, drawings must indicate fire rating for partitions, ceiling, walls; location of penetrations through fire rated assemblies; and schedules for doors, windows and finishes materials. Habitable rooms must be dimensioned with notes on light and air compliance.

Façade Elevations. Required if the project involves the renovation or modification of the building exterior and in some cases also required for interior renovations that may impact the façade.

Sections. Might be required for documenting some types of renovation projects. These could include building sections.

Detail Drawings. These drawings contain significant information required to clearly communicate the scope of work, in a magnified form.

Energy Analysis. Energy Analysis shall be provided on drawings in the form of Tabular Analysis, ComCheck, or energy model. Energy Analysis references supporting documentation location and the corresponding values match the proposed construction on drawings. For projects claiming exceptions, details shall be clearly shown in the analysis supporting the reason for the exception. Some key elements required on plans for all projects include:

Provide the correct Code reference citations to either NYCECC or ASHRAE 90.1

Energy Code Progress Inspections shall be listed on the drawings, based on the scope of work.

Energy Analysis shall be provided on drawings in the form of Tabular Analysis, COMCheck/RESCheck, or energy model. Energy Analysis references supporting documentation location and the corresponding values match the proposed construction on drawings. For projects claiming exceptions, details shall be clearly shown in the analysis supporting the reason for the exception.

Exterior wall/roof/floor:

Opaque envelope assembly components are annotated with proper R-value and/or U-factors, and correctly calculated, including thermal bridging effects. Air sealing details are clearly identified.

New vestibules shall meet envelope, heating and cooling provisions.

Weather seals are required

Vertical glazing, skylights, doors:

Fenestration assembly U-factor, air leakage values are identified, and any increase in fenestration area are clearly identified on drawings.

Lighting

Fixture Schedule shall be provided and include type designation, brief description, location of fixtures, lamp type, ballast/transformer type, watts per fixture, and controls scheme. Schedule shall be keyed to lighting plans. Lighting shall meet the power requirements and the controls.

Daylight zones adjacent to vertical glazing and beneath skylights are clearly identified on the lighting plans.

HVAC

Equipment has met the sizing requirements.

Indicate equipment capacity, model number, rated efficiency and controls requirements (e.g. part-load, reset controls, pump modulation, demand controlled ventilation, economizers, energy recovery)

Indicate shutoff damper controls for outdoor air intakes and exhausts

Identify duct insulation location, R-value, and details indicating joints and seams are sealed

Identify piping insulation location and thickness

Indicate provisions for Commissioning and completion requirements.

If applicable, additional elements required on drawings include:

Accessibility for persons with physical disabilities to comply with BC Chapter 11

Façade, roofing, and parapet walls with details

Lot Line windows or new openings in accordance with permitted percentages

Building systems and equipment details*

Manufacturing process systems, related equipment and details

Flood zone compliance

*Refer to Project Guidelines for Building Systems installation and modification projects.

Submission of Construction Documents

When submitting the construction documents to the Department, the Registered Design Professional, Applicant of Record, is responsible for submission of complete set at filing: application, drawings, and coordination of required documents as summarized below.

Drawings. The renovation project drawings should reflect clear scope of work and include all affected systems. Examples of this are as follows:

Designator - Sheet Number:
Sheet Description

T-001.00
Title Sheet, Site Plan, Drawing Index, General Notes, required special/ progress inspections list, and Legends

A-100.00
Existing and Demolition Floor Plans

A-101.00;
Proposed Floor Plans

A-200.00
Proposed Reflected Ceiling Plans

A-300.00
Proposed Enlarged Floor Plans

A-301.00
Proposed Interior Elevations and Details

A-400.00
Existing and Proposed Façade Elevations

A-401.00
Existing and Proposed Cross Sections

S-100.00
Structural Plans and Details

P-100.00
Floor Plans - Plumbing

P-101.00
Plumbing Riser Diagram – Gas Riser Diagram - Piping

P-102.00
Plumbing Fixture Schedules – Plumbing Details

SP-100.00
Sprinkler Floor Plan

SP-101.00
Sprinkler Riser Diagram and Details

M-100.00
Mechanical System Equipment and Schedules

M-101.00
Reflected Ceiling Plan for Mechanical System

EN-100.00
Energy Code Analysis

FS -100.00
Food Service Equipment and Systems (if applicable)

Q-100.00
Equipment (various, if applicable)

Drawing Legend to include: Symbols, abbreviations, notes and definition, and list all applicable Building Code section numbers

Recommended Drawing Designators
A: Architectural: Mandatory designation for drawings showing architectural work.
S: Structural: Mandatory designation for drawings showing structural work.
P: Plumbing: Mandatory designation for drawings showing Plumbing work including riser diagrams and plumbing details
SP: Sprinkler: Mandatory designation for drawings showing sprinkler work including floor plans, riser diagram and sprinkler system details
M: Mechanical: Mandatory designation for plans showing mechanical work
EN: Energy Analysis: Mandatory designation.

*Note: In manufacturing facilities, special equipment is often required. In these cases drawings with different drawing designators are also provided. For example, 'FS' is used as a designator for fuel storage equipment drawings, while ‘Q’ could designate other types of process related equipment.*

Required Documents. Based on buildings location and designation, and the project’s scope of work, the following submissions may have to accompany the drawings at intake:

DEP, or OER authorization

FDNY – Notification or Letters of No Objection

Tenant/Occupant Protection Plan (only if applicable)

Mayor Office for People with Disabilities (MOPD)

FEMA (Federal Emergency Management Agency) – FEMA Map

Transit Authority Approval

DOT Approval

Landmark approval

Public Design Commission Approval – NYC owned properties exterior work only

Post Approval Amendments. Any changes to approved scope of work that are significant and substantive will require submission of revised document and /or plans for Post Approval Amendment (PAA). Approval for an amendment must be obtained before the work is completed. Changes that are not substantive do not require a PAA; however these changes must still be shown on plans and included in the As-Built submission at the end of the project (AC 28-104.3)

Expand scope of work to include an additional space in the same or different story. For example, expand the first floor renovation to a space in the basement or cellar below.

Changes in function of areas and rooms from what was shown on approved plans. For example, the function of a portion of an assembly space is changed to a new conference room or an office space.

Expand scope to add, replace or modify building equipment, roof systems, etc.

Structural changes

Addition or removal of the following: plumbing risers, minimum required fixtures, roof drains, etc.

Any alteration of gas systems

Changes to scope of work that require additional Special or Progress Inspection(s)

Substantive changes that meet the following criteria should be submitted for review to amend the approved plans:

As-Built Submission. All changes must be submitted in an ‘As-Built’ drawing at the end of the project. Any changes affecting the energy analysis will require an update to the energy analysis.

Special Inspections

As per BC Chapter 17, renovation work may require certain Special and Progress Inspections to be performed during and at the end of construction as outlined in the table below. Prior to Approval, the Applicant of Record is required to identify all required Special and Progress Inspections (BC 1704.1). Prior to DOB permit issuance, the Owner must typically engage a registered Special Inspection Agency (SIA) who will take responsibility for the Special and Progress Inspections. The Applicant of Record may perform these inspections if they are also an SIA. Inspection discrepancies and hazardous conditions must be reported to the super-intendent of construction, as well as to the Site Safety Coordinator or Site Safety Manager, for correction, per BB 2016-006 and 1 RCNY 101-06. Per BC 1704.1.2, the Contractor cannot hire the Special Inspector.

Based on the scope of work, a sign project may be required to comply with the following Special and Progress Inspection requirements:

Structural Steel

May include steel welding, High Strength Bolting and Steel Details (BC 1704.3).

Concrete: Cast-In-Place and precast

Required where the total concrete placement on a given project is more than 50 cubic yards or other conditions. Precast may be needed during façade renovation project (BC 1704.4)

Wood – Installation of Prefabricated I-Joists

Are subject to Special Inspections in accordance with Section 1704.2 and the requirements of Section BC 2303.1.2, (BC 1704.6.3).

Wall Panels, Curtain Walls and Veneers

Required for exterior architectural wall panels and the anchoring of veneers designed for installation on buildings above a height of 40 feet. Special Inspection of masonry veneer on such structures shall be in accordance with Section 1704.5 (BC 1704.10).

Sprayed Fire-resistant Materials

Special Inspections for sprayed fire-resistant materials applied to floor, roof and wall assemblies and structural members shall be in accordance with Sections 1704.11.1 through 1704.11.7.

Structural Stability – Existing Buildings

Alteration of existing structural systems or elements, such as columns, girders, beams, bearing walls, etc. where the stability or integrity of a structural system is to be temporarily diminished, in accordance with Sections 1704.20.6 through 1704.20.10.

Excavations – Sheeting, Shoring, Bracing and Underpinning

Methods employed to protect the sides of excavations shall be subject to Special Inspections in accordance with BC 1704.20.3, BC 1704.20.2 and BC 1814.

Fire-resistant Penetration and Joists

Special Inspections for penetration of fire-resistant elements and assemblies; and related firestops in accordance with Sections 1704.27.1 and 1704.27.2.

Flood Zone Compliance

Special Inspection for flood zone compliance shall be as required by BC Appendix G and BC 1704.29. Also progress inspection for lowest floor level per BC 110.3.2.

Masonry

Load bearing masonry, glass unit masonry and masonry veneer shall be inspected and verified in accordance with the requirements of sections BC 1704.5.1 through BC 1704.5.3, depending on the structural occupancy category of the building or structure.

Footings and Foundation

Footing and foundation inspections shall be made after excavations for footings are complete and any required reinforcing steel and required forms are in place as per BC 110.3.1.

Structural Wood Frame

Inspections shall be performed for wood structural framing to determine compliance with the approved construction documents as per BC 110.3.3.

Fire-Resistance Rated Construction

Fire-resistance-rated partitions, floors, ceilings, shafts, and shutters as per BC 110.3.4.

Energy Code Compliance Inspections

Inspections shall be performed to determine compliance with the approved construction documents and RCNY 5000-01

Design Professional Links

Manufacturing Checklists

Requirements: Renovations

Checklists: Renovations

Design Professional Project Checklists

Design Professional Project Requirements

Design Professional Project Guidelines

Helpful Links

Project Categories

Key Points & Project Terms

Project Phases & Requirements

Project Checklists

Working on Your Project

Compliance & Violations

Information for Master Plumbers

Insurance Guidelines

DOB NOW

Code Notes

Find Licensed Professionals