Question: Write a note on setting out alignment of road.


Question: Explain any two speed control techniques used in wind turbine to extract maximum power.


Question: Compare stack with Queue.


Question: What are the requirements for Linux system administrator?


Question: Explain Carbon Arc Welding neat sketch.


Question: What are the mathematical operations that can be performed on SET Abstract Data Type?


Question: Explain the Pneumatic Power supply with neat sketch.


Question: Explain with neat diagram and output waveforms, Op-Amp as a zero crossing detector?


Question: Draw interfacing diagram of LED with Arduino board also write the algorithm to blink the LED.


Question: Explain applications of remote sensing in civil engineering.


Question: Explain stiffness and flexibility and write elements of displacement matrix for the frame shown in figure 7.


Question: Define terms.


Question: Explain the important components of gas chromatography.


Question: Explain the role of technology in innovation.


Question: Enlist the various methods of concrete mix design.


Question: Classify different types of ADC and explain iwth diagram dual scope ADC.


Question: Describe the ARM design philosophy.


Question: What are the various losses which make the operation of actual cycle differ from that of air standard cycle Explain each loss in brief.


Question: Two wattmeters connected to measure the input to a balanced 3-phase circuit indicate 2000 W and 500 W respectively. Find the power factorof circuit: i) When both the readings are positive ii) When the latter reading is obtained after reversing the connections to the current coil of first instrument.


Question: Evaluate () ( )3 2 C5 12zdz zz− +−  where C is the contour 3z=.


Question: Draw and explain torque-Slip characteristics of 3 phase induction motor with respective mathematical expressions. Clearly mark the two regionsand point of maximum torque and starting torque


Question: What is projection?


Question: Derive general three dimensional heat conduction equation in Cartesian coordinates.


Question: What is a friend function?


Question: The voltage V( s) in a network given by :


Question: Explain basic concept of Hash table?


Question: How folds are developed?


Question: Explain Interdomain and Intradomain routing protocol in detail.


Question: Comment on Unconfined Compression test is special case of Triaxial Compression test.


Question: Use Cachy's integral formula to evaluate 2z Cedzz where C is the circle |z + 2| = 2.


Question: Calculate the rate of heat loss from a thermoflask if the polished silver surfaces have emissivities of 0.


Question: How packaging is promoting the product in market explain in detail.


Question: Sketch & explain the Torque- Armature current characteristics of


Question: Two straights AB and BC meet at chainage of 3450 m.


Question: Explain low drop out regulator with neat diagram in detail.


Question: Discuss the significance of topological sorting.


Question: Explain standalone renewable system with neat diagram.


Question: Consider the following Book Relation.


Question: Explain Advantages of frequency Domain Analysis.


Question: With neat diagram explain working of IC 555 as a Astable Multivibrator.


Question: What is RTD?


Question: Analyse the continuous beam shown in figure 6 by moment distribution method.


Question: Explain the different types of flames used in oxyacetylene welding.


Question: An oil of viscosity 0.


Question: Write down various applications of Nanomaterials in Chemical industries.


Question: Write a program using put ( ) to write characters to a file until user enteres a dollar sign.


Question: A Rankine cycle operates between pressure of 80 bar and 0.


Question: Compare PVD and CVD coating.


Question: State properties of material used for solders.


Question: Define Magnitude response and phase response.


Question: Classify hydro electric power plant based on i) head ii) load


Question: For an Unity feedback System with open loop transfer function 4G(S)(2 )ss. Determine Damping factor, Undamped natural frequency, reason peak, resonant frequency.


Question: Illustrate with suitable circuit diagram inverting comparator.


Question: Define monochromatic emissive power and monochromatic emissivity.


Question: Explain the terms enantiomers and diastereomers giving examples.


Question: Perform depth first search algorithm on the following graph.


Question: Explain the various methods of speed control of dc series motor.


Question: Write Note on Copper and its Alloy.


Question: The crank of an engine is 200 mm long and the ratio of connecting rod length to the crank radius is 4.


Question: Explain the input and output module of programmable logic controller.


Question: Draw neat diagram and explain operation of 3 pt.


Question: Define Condensation?


Question: Explain Architecture of Distributed database system.


Question: Differentiate between Latch and Flip Flop.


Question: Compare vertical axis and horizontal axis wind turbine.


Question: Explain white cast iron with its composition.


Question: What is test case design?


Question: Draw and explain programmers model of ARM processor.


Question: State the significance of volume boosters and explain volume booster in brief.


Question: A horizontal venturimeter with inlet and throat diameter 30cm and 15cm resp is used to measure the flow rate of water.


Question: A  tacheometer with analystic lens.Having the multiplying constant 100 was used and the following observations were made on staff held vertical.


Question: Difference between unavailable and available energy.


Question: Write the JavaScript code to create Login page Form.


Question: Write short note on stainless steel?


Question: Explain the need of level shifting stage in op-amp. Explain any one circuit for the same.


Question: What are extrusive and instrusive Igneous bodies?


Question: What is a user defined exception?


Question: Draw the circuit diagram of full wave preusion rectifier and Explain.


Question: Explain Network Address Translation with suitable diagram.


Question: What is halftone and how it is created.


Question: What is the ambiguity that arises in multiple inheritance?


Question: A pressure vessel having outer diameter 1.


Question: A three phase 50 Hz overhead transmission line consist of three conductors each of diameter 0.


Question: Tabulate different methods of control of microorganisms with its mode of action and examples.


Question: Define Time Division multiplexing.


Question: Discuss the advantages of using container adapters in the STL.


Question: Describe eye pattern Graphical Display of Inter Symbol Interference with diagram.


Question: Find the shortest path from node ‘a’ to all nodes in the graph shown in fig.4 using Dijkstra’s algorithm.


Question: Explain the classification of Alloy Steel with respect to the relation with carbon.


Question: Design a 3-Bit synchronous counter using JK FF.


Question: Find the Shear Force Diagram and Bending Moment diagram for beam in figure below.


Question: Construct the binary search tree (BST) from the following elements.


Question: Differentiate between pull and push broaching and mention types of broaches.


Question: Write a pseudo code to insert new node in to singly link list.


Question: What is states of counter?


Question: Using Gauss - Divergence Theorem, show that


Question: What is page replacement in operating systems?


Question: Enlist the limitations of the prevalent survey techniques and also give advantages of Space Based Positioning System.


Question: Explain the condition of Reciprocity & Symmetry by giving Example.


Question: Explain midpoint circle generation algorithm by deriving the steps.


Question: What is conformational isomerism?


Question: State  and explain the working principle of the DC generator along with a diagram.


Question: Explain in detail categories of Software Metrics with suitable examples.


Question: Design a sequence generator using T FFs.


Question: What is the difference between Testing and debugging?


Question: Calculate the split tensile strength of following specimen of concrete.


Question: Write pseudo code for BFS of a graph and explain it with suitable example.


Question: Explain A VL tree rotations with example.


Question: Calculate the heat of formation of ethane gas at 298.


Question: If 1G(S)H(S) .(s 1)s Find Resonance peak and resonance frequency.


Question: Washer with 12 mm internal hole and 25 mm outside diameter is to be made from a strip of 1 .


Question: Explain deferred database modification and immediate database modification and there difference in the context of recovery.


Question: Explain the interrupt structure of PIC18 along with IVT.


Question: What do you mean by EV A?


Question: Explain different types of exceptions in 80386 with suitable examples.


Question: Derive the expression for the torque of the DC machine.


Question: Draw and explain the characteristics of a DC shunt motor.


Question: What is software quality?


Question: Crank OA of a compound slider crank mechanism as shown in fig.


Question: Explain Network stability.


Question: A point in a strained material is subjected to stress as shown in figure 7.


Question: What is carburetor?


Question: Write a note on assembly language elements.


Question: Explain the types of models in Batch Process.


Question: Define Binary Tree. What are its types? Explain with suitable figures.


Question: Explain the SOC, EOC, & OE pin of ADC 0809.


Question: Explain with diagram the process scheduling in Linux.


Question: Explain on Devices Security and Privacy of IoT cloud.


Question: Describe Logical Programming.


Question: Explain Demand and supply curve.


Question: A water tower is supported only on three pillars forming an equilateral triangle with 10m side.


Question: Draw and explain IPv4 header format.


Question: Define the importance of Project estimation.


Question: How to enhance decision making with information systems give suitable examples.


Question: Draw circuit diagram of current mirror circuit and explain in detail.


Question: Find center of pressure of the component as shown in fig.


Question: Explain with neat diagram construction and  working of IBM processes.


Question: With the help of block diagram explain Power measurement using 8051.


Question: A wall of furnace is made up of inside layer of silica brick 120 mm thick coverd with a layer of magnesite brick 240 mm thick.


Question: An unbiased coin is thrown 10 times.


Question: Write note on Artificial intelligence in automation.


Question: Draw a neat sketch and write a short note on rotating matrix heat exchanger.


Question: Draw and explain with neat sketch of simple carburetor.


Question: What is meant by hidden surface removal?


Question: Explain Friction Circle Method with neat sketch.


Question: What do you understand by Leadership in Energy and Environmental desing (LEED)?


Question: Write a short note on land use zoning and mention the requirements of each.


Question: Derive the expression with usual notations for total pressure and centre of pressure for vertical plane surface submerged in liquid.


Question: What is mean by primitive data type and list out primitive data types available in Java with example?


Question: Write an 8051 C program to toggle only bit P2.


Question: Explain data preprocessing with example.


Question: List various properties required for bearing material?


Question: A solid circular shaft 8 m long is securely fixed at both the ends.


Question: Explain the procedure for unconfined compression test with neat sketches.


Question: What is the difference between PAL and PLA.


Question: Draw and explain block diagram of memory devices.


Question: Explain rotation about an arbitrary point in 2D.


Question: What is Priming?


Question: Derive an expression for heat exchanger effectiveness for concurrent flow.


Question: Illustrate operation of PLL with suitable block diagram.


Question: Explain the key features of object oriented programming language.


Question: Explore memory management in the Virtual 8086 Mode.


Question: Apply Green's theorem to evaluate : 2() Cxdx xydy Where C is the curve of region enclosed by y = x2 and the line y = x.


Question: Describe the major Design Rules of RISC philosophy?


Question: Explain Gauss Seidel method for solution of simultaneous equation.


Question: Explain the concept of thermal diffusivity and thermal contact resistance.


Question: Write a program to write below letters by Robot using VAL Language.


Question: Explain the interfacing of LED with Arduino board and write an algorithm to blink an LED frequently.


Question: State any six properties of fourier transform.


Question: Suppose heights of students follows normal distribution with mean 190 cm and variance 80 cm 2. In a school of 1000 students, how many would you except to be above 200 cm tall? (Given, z = 1.1180, A = 0.3686).


Question: Explain the virtual memory system with suitable diagram.


Question: The crank of IC.


Question: A circular bar of diameter 80 mm diameter is subjected to axial compression force of 200 kN. Determine shear stress on a plane, onwhich the normal stress is 100 MPa.


Question: Show BFS and DFS for the following graph with starting vertex as 1.


Question: Describe factors impacting on entrepreneurship.


Question: Define foundation.


Question: Differentiate between TIG welding and MIG welding.


Question: What is a strategic information system?


Question: Draw circuit diagram of first order wide band stop filter with its frequency response.


Question: Draw neat sketch of combined curve with its notations.


Question: A set of five similar and fair coins are tossed 3360 times.


Question: Write short notes on:


Question: What is an adsorption isotherm?


Question: Compare variable Reluctance and permanent magnet stepper motors.


Question: Explain the applications of Virtual Reality systems.


Question: Describe Circumstances under which you would choose to use Embedded SQL than normal SQL or only a general purposeprogramming Language.


Question: Derive an expression for digital PID velocity algorithm and state the merit of velocity algorithm.


Question: A cantilever of length 3 m carries a uniformly distributed load over the entire length.


Question: With suitable diagram explain construction and working of LVDT.


Question: What is configuration identification in SCM?


Question: Find the coefficient of correlation for following data.


Question: Explain the Geological conditions favorable for natural springs and artesian wells.


Question: Between 2 pm to 4 pm the average no of phone calls per minute coming into a switch board of a company is 2.


Question: Differentiate between Kaplan and Pelton wheel turbine.


Question: What are elements of Design model?


Question: State the Flexural formula and explain the meaning of each term in it?


Question: Define Cast Iron?


Question: What are different methods of sounding,State any one method in detail?


Question: Let p is the probability that a given die shows even number.


Question: Apply the Gauss Jordan method to solve the following equations.


Question: List the different architectural styles.


Question: A coin is tossed 160 times and following are expected and observed frequencies for number of heads.


Question: Write a short note on fetching a word from Memory.


Question: What do you mean by spontaneous magnetization?


Question: State performance parameters of transmission line hence explain how ABCD constants are useful for determining these parameters.


Question: Write functions for RR and RL rotation with respect to AVL tree.


Question: Define member stiffness; carry over moment and distribution factor.


Question: Draw two possible connections of wattmeter for power measurement in single phase circuit.


Question: Construct a divided difference table from the following data.


Question: With suitable labelled diagram explain constructional details of single phase induction type energy meter.


Question: What is meant by springs?


Question: What do you mean by adjacency matrix and adjacency list.


Question: Explain Construction and working Principle of single-phase induction motor.


Question: A perfect die is thrown. Find the probability that


Question: Evaluate F cdr  along the straight line joining points (0, 0, 0) and (2, 1, 3) where 2= F = 3 2 xix z y j z k


Question: Distinguish between combinational and sequential switching circuits also write examples of both.


Question: What is Virtual function? Explain how to achieved run time polymorphism.


Question: Explain Hot dipping and Burnishing processes in detailed.


Question: What is doubly linkedlist.


Question: Explain the process of municipal solid waste to energy conversion with diagram.


Question: Explain sequence of events that occur in Fetch cycle symbolically with diagram at each stage.


Question: 3 vdv b) 21 vdvr c) vdv d) 0 v) Inverse shifting operator is equivalent to.


Question: What are sound displays in Virtual Reality?


Question: Explain Interrupt Priority Register of 8051 Microcontroller.


Question: Calculate the coefficient of variation for the data given as follows.


Question: Explain the thread life cycle model in Java.


Question: Derive the expression for minimum starting speed of a centrifugal pump.


Question: What are the measure of query cost?


Question: Write a short note on causes and remedial measures of landslides.


Question: What is stream? Explain types of streams available in C++.


Question: Explain with example Forward and Backward Selection method for Subset Selection.


Question: Calculate Molarity and Normality of solution containing 0.


Question: Draw and Explain WSN architecture?


Question: What is landslide?


Question: What is the duty cycle of a motor?


Question: State the applications of SBPS surveying?


Question: Explain in detail the importance of preliminary geological exploration in civil engineering projects.


Question: Brief the concept of byte streams?


Question: Find the Laplace Transform of following signals.


Question: Two parallel shafts having centre distance 5 meters are connected by open flat belt.


Question: Define quality.


Question: In a sample of 1000 cases a mean of certain test is 14 and standard deviation is 2.


Question: The following observations were made using a tacheometer fitted with an analytic lens, multiplying constant being 100.


Question: Define Red Black tree.


Question: Write short note on nervous tissue.


Question: How test strategies for object oriented software are different from that of conventional software?


Question: Solve the following integral equations.


Question: An emitter biased Dual Input Balanced Output differential amplifier has the following specifications.


Question: Define Aquifers. Explain in short the types of aquifers.


Question: Enlist non destructive tests for concrete.


Question: Write a short note closed loop control of Induction motor drives.


Question: Explain the applications of IR spectroscopy.


Question: Enlist features of a good hash function.


Question: Explain with neat diagram the register weighted and R-2R DAC?


Question: In the toggle mechanism shown in Fig.


Question: What is an exception in JA V A?


Question: Discuss the different types of threads used in power screw.


Question: A certain feedback system is described by the following transfer function.


Question: Explain the use of command line arguments.


Question: Define indegree and outdegree of a vertex in graph. Find the indegree and outdegree of following graph.


Question: What is projection?


Question: Explain any three methods of subsurface investigation.


Question: The 45 mm diameter of shaft is made of steel with the yield strength of 400 MPa.


Question: What is Semaphore?


Question: State any four significant features of Arduino IDE.


Question: Explain theory of stadia tacheometry?


Question: Which of the following codes are prefix codes?


Question: Explain the methods of measurements of solar radiations.


Question: State and explain terminology for spur gear with neat sketch.


Question: What is pressure bulb?


Question: What is retained austenite?


Question: What do you understand by relative humidity of air?


Question: Explain with sketch any one technique of Polymer matrix composite processing.


Question: State the significance of volume boosters and explain volume booster in brief.


Question: Explain the types of HMI?


Question: Write short note AT commands required for GSM.


Question: Describe in brief process description of manufacture of Olefin by polymerization using phosphoric acid on solid carrier as catalyst.


Question: Find the directional derivative of 2xyzeφ−−=  at (1, 1, 1) along the line 111 122x yz −−−== .


Question: Differentiate between ROM and RAM.


Question: Define lipids and enlist the functions of lipid.


Question: Explain following routing.


Question: Explain Artificial Neural Networks with suitable examples?


Question: Explain deadlock prevention and Recovery.


Question: What do you mean by flow control in transport layer?


Question: Explain cache updating policies in detail.


Question: Write a short note on CPLD.


Question: Explain containment and Inheritance along with examples.


Question: With a neat block diagram explain AC voltage measurement using 8051 microcontroller.


Question: Calculate the weight of KMnO4 required making 500 ml of 0.


Question: List out the factors affecting electro deposition.


Question: Explain the contents of project Feasibility report with example.


Question: What are different file opening mode?


Question: What is exception and its types?


Question: A cylindrical boiler is 2.


Question: What are different types of curves, explain any one with sketch .


Question: Describe the types of a servo motor.


Question: Construct an AVL Tree by inserting numbers from 1 to 8.


Question: Explain the phenomenon of spontaneous polarization in ferroelectric materials.


Question: Explain the ring counter design for the initial condition 1010.


Question: State any six properties of Laplace Transform.


Question: Following are the details of Project A and B.


Question: State the various types of non-destructive tests carried on hardened concrete. Explain ultrasonic pulse velocity test with its limitations.


Question: Derive an expression of shear stress and velocity distribution for lamiral flow through circular pipe.


Question: Define pressure vessels and explain design of pressure vessels subjected to external pressure.


Question: A symmetric I section is having two flanges, each of 300 mm × 20 mm and vertical web of 20 mm thickness and 160 mm depth. The beam issubjected to shear force 200 kN. Draw Shear Force Distribution diagram.


Question: Implement the given logic function using a 4:1 multiplexer


Question: Draw and explain the block diagram of DSO.


Question: Prove the following identities (any one)


Question: Write note on High temperature alloy.


Question: What is significant depth and pressure bulb?


Question: Determine the eq ns of regression lines for the following data.


Question: Explain static and dynamic tree tables with suitable example.


Question: Explain any two detectors used in gas chromatography.


Question: Explain the necessity of providing fire protection system in building.


Question: The  results of measurements of electric resistance R of a copper bar at various temperature are listed below.


Question: Explain advantages of indexing over sequential file.


Question: Explain various process management system calls in Linux with example.


Question: Attempt any one:


Question: Which are the key properties of nanomaterials?


Question: Explain the stepper motor interfacing with PIC18FXX microcontroller with suitable diagram.


Question: Explain CPLD with the help of neat logic diagram.


Question: Draw and explain an Instrumentation amplifier interface with RTD bridge for temperature measurement.


Question: Draw the SCON register and explain use of individual bits of the register in detail.


Question: What are turbines?


Question: What do you mean by Widmanstatten Structure?


Question: What are the different types of Financial Analysis?


Question: Mention the ingredients of cathode and anode for following batteries.


Question: Explain the concept of instruction pipelining with diagram.


Question: Define fixed and variable voltage regulator.


Question: Evaluate .


Question: Explain properties of insulating materials which are used in Capacitor and Rotating Machines.


Question: State and prove initial and final value theorem.


Question: The speed (km/hr) of a train which starts from rest is given by the following table, the time being recorded in minutes.


Question: Describe with neat diagrams  - Boron Nano Tubes.


Question: Explain two types of rotor construction of a three phase induction motor with the help of suitable diagrams.


Question: Compare array and linked list.


Question: With the help of diagram explain the concept of solar thermal power plant.


Question: What is graphics rendering pipeline in a Virtual Reality system.


Question: Explain in detail combined diffuse and specular reflections with multiple light sources.


Question: In a geometrically similar model of weir the discharge is 0.


Question: Compare late binding & early binding.


Question: What are the symptoms and diagnosis of distress of concrete?


Question: Deduce the equation of maximum work done in terms of volume and in terms of pressure.


Question: What is mean by earthquake resistant structures?


Question: Explain following instructions of 8051.


Question: Analyze bent ABC as shown in Fig. 7 by moment distribution method.


Question: Compare the role of thread diameter with ink transfer in screen printing process.


Question: Write a note on the dam located on folded geological structure.


Question: Explain generation of saw tooth waveform using OP-AMP. Draw input & output waveforms.


Question: Elaborate on detectors used in AC bridges.


Question: Define the following terms with suitable example with respect to Binary tree:


Question: What is the Importance of Good Communication Skills?


Question: Determine the probability of getting sum 10 exactly twice in three throws with a pair of fair dice.


Question: Find the Trignometric Fourier Series for the periodic bidirectional symmetric square waveform below.


Question: Write short note on Satellite Alloys?


Question: Explain construction and working principle of Kaplan Turbine with application.


Question: Difference between Real Mode and Virtual 8086 Mode.


Question: Design a cast iron protective type flange coupling to transmit 15 kW at 900 RPM from an electric motor to a compressor.


Question: State the following properties of CTFT.


Question: A string of suspension insulators consists of four units.


Question: Compare Electric System with pneumatic system.


Question: The screw of a shaft straightener exerts a load of 30 kN as shown in Fig.


Question: Explain specific energy curve.


Question: A rectangular plane surface 3m wide and 4m deep lies in water in such a way that its plane makes an angle of 30º with the free surface of water.


Question: Define Queue and explain any one application of Queue.


Question: Delineate modulus of counter.


Question: Explain the different types of ADCs.


Question: A beam ABC of length 10m has one support at the left end other support at a distance of 6m from the left end.


Question: Explain with neat sketch the Peak and Residual shear strengths of soils.


Question: Draw a neat labeled sketch of semicircular - arch and show:


Question: Find maximum torque that can be safely applied to a shaft of 75mm diameter.


Question: Draw and explain operational model of network security.


Question: An unbiased coin is tossed five times.


Question: Describe the construction and working of the Universal motor with the help of suitable diagrams and state its two applications.


Question: Calculate first four moments about the mean of the following distribution.


Question: Sort the following numbers using Quick sort.


Question: Explain Hilbert curve and give its fractal dimension.


Question: What is a servo motor?


Question: Explain any two methods of speed control of DC shunt motor.


Question: Explain in short:


Question: How Basic Arithmetic operations are performed using ALU IC 74181?


Question: A pipe of 110 mm diameter is carrying water. If the velocities at the pipe center and 30 mm from the pipe centre are 2.1 m/s and 1.6 m/srespectively and flow in the pipe is turbulent. Calculate the shear frictionvelocity and wall shearing stress.


Question: Differentiate between SCADA and HMI.


Question: Explain construction and working of a synchronous machine.


Question: What is A VL tree? Explain all the rotations in A VL tree. Construct A VL tree for the following data:


Question: Write a short note on purging of vessels.


Question: Describe in detail about purification of protein by affinity chromatography.


Question: Draw and explain the functional diagram of 723 regulator.


Question: Compare fire resisting properties of concrete and stone.


Question: With neat circuit diagram explain I to V converter.


Question: Differentiate between sequence containers and associative containers in the STL.


Question: What do you mean by memory management operator?


Question: Discuss in details role of Encoder in robotic system.


Question: Explain Classification of channel bottom slopes with neat sketches.


Question: Draw and discuss the dead weight tester with diagram.


Question: State the features of RTC.


Question: Sate the working principle and applications of total station?


Question: Discuss in detail Proctor needle in field compaction control.


Question: What is importance and purpose of Refining process in manufacturing of paper.


Question: Write a short note on rating system for green building.


Question: Find the Fourier Transform of sine wave signal and sketch magnitude response and phase response.


Question: Write down the steps to be followed to receive a data serially using 8051 microcontroller.


Question: Describe Logical Programming.


Question: Define hardenability.


Question: A retaining wall with a smooth vertical back retains a purely cohesive fill.


Question: Define load factor and shape factor.


Question: Explain zero crossing detector using OP-AMP with necessary waveform.


Question: Explain a binary tree. Name and explain with suitable example the following terms:


Question: Draw and explain the operation of single phase bridge rectifier supplying RL load.


Question: What is topological Sorting?


Question: Use dijkstras algorithm to find the shortest path between A and Z in figure.


Question: Explain Sensitization and Weld Decay.


Question: Evaluate 1 2 01dx x using Trapezoidal rule taking h = 1 4.


Question: Write note on stiffness method and write elements of displacement matrix for following figure.


Question: Assuming that the diameters of 1000 brass plugs taken consecutively from a machine form a normal distribution with mean 0.


Question: Explain regenerative braking in case of DC motor.


Question: With neat sketch explain the HGL and TEL.


Question: State the classification and applications of Photogrammetry in surveying.


Question: A pressure vessel is required to have a capacity of 20 m 3.


Question: Write a program in C language to copy the contents of Port 2 to Port 1.


Question: Fig.


Question: Explain the TSS descriptor and its role in multitasking.


Question: Explain truncation error and round off errors with example.


Question: Derive the expression for state transition matrix by Laplace transform method.


Question: Explain following terms in brief.


Question: Using Jacobi iterative method solve the following system of linear simultaneous equations.  Take x (0) = y (0) = z (0) = 0 perform 5 iterations.


Question: Write a program in C language to toggle only bit P1.


Question: Explain ISA sequence in Alarm Annunciation system.


Question: What is Template?


Question: Explain in details Temperature Control Methods of Furnaces.


Question: Sketch a twist drill geometry and discuss various elements of it.


Question: Explain in brief the durability of concrete.


Question: Clearly explain why induction motor is known as generalized transformer.


Question: Explain any three grinding operations.


Question: The armature of 4 pole DC shunt motor has LAP winding which is accommodated in 60 slots, each slot carries 20 conductors.


Question: State the procedure for tacheometric contouring?


Question: Write short note on lamination methods.


Question: Draw RC coupled amplifier.


Question: Explain any one method of viscosity measurement.


Question: Evaluate F.


Question: Explain traversing the nodes in linked list with neat diagram.


Question: Compare the thermosetting plastics and thermoplastic.


Question: What are the methods used to handle Deadlocks.


Question: Describe with neat diagrams - Carbon clusters.


Question: What is an ASM Chart?


Question: What are various types of Stepper motors?


Question: Derive the formula for Newton’s forward interpolation formula for the equally spaced data points.


Question: Explain error handling during file operations.


Question: A helical spring is made from a wire of 6 mm diameter and has outside diameter of 75 mm.


Question: Represent the following polynomials using linked list.


Question: Write detailed classifications of Internal combustion engines.


Question: Illustrate the various IoT communication APIs?


Question: Define with example.


Question: What is mean by user defined exception?


Question: Discriminate between Brazing and Soldering.


Question: State Lambert and Beer laws and derive the combined law equation.


Question: What are different types of jois in SQL?


Question: Explain the block diagram of electric vehicles State advantages and limitations of Unit 6.


Question: The armature resistance of a DC shunt motor is 5.


Question: State four features of LAP winding of DC machine.


Question: What is gas chromatography?


Question: What is Isobar and Pressure bulb?


Question: Illustrates causes and remedial measures of landslide.


Question: What is OBST in data structure?


Question: With the help of Block diagram explain superheterodyne FM receiver.


Question: Write a short note on ALU IC 74181.


Question: Write short note on Invar?


Question: Find the Laplace Transform and ROC of Unit Step function and Unit Ramp function.


Question: What is heat engine?


Question: Describe in detial  Read Only Memory (ROM).


Question: Explain error handling during file operation.


Question: With neat diagram explain different components and their functions in horizontal axis wind turbine.


Question: 15 11 25 10 12 20 15 10 17 13 P .


Question: Explain Dequeue with the insert and delete operations performed on it.


Question: An incomplete travers table is obtained as follows.


Question: What are the advantages of forging over the casting process?


Question: The first four moments of distribution about working mean 3.


Question: Explain the working of an universal motor with help of suitable diagram.


Question: Explain difference between squirrel cage induction motor and slip ring induction motor.


Question: What is method overriding?


Question: Define plastic hinge, load factor and shape factor.


Question: Define Task Switching and explain the steps involved in task switching operation?


Question: What do you mean by equality of sets.


Question: Astring is stretched and fastened to two points L apart.


Question: Explain the stack organization and enlist instructions related to stack.


Question: What is semaphore?


Question: Write Note on Aluminum and its Alloy.


Question: State four temperature scale available give conversion formulae of it.


Question: What is package in Java?


Question: Explain the operation of Wien bridge oscillator with neat circuit diagram.


Question: What are dirichlet conditions for existence of fourier series.


Question: Write down the Applications of Nanomaterials in chemical industry.


Question: Differentiate between Cysteine and Cystine.


Question: List and explain various features of virtual 8086 mode.


Question: List the types of Lubricants with at list two examples.


Question: What are the elements that exist when an effective SCM system is implemented?


Question: Explain various debugging feature of 80386.


Question: Explain in detail vulnerabilities of Internet of Things.


Question: Explain with neat sketch variable head permeability test.


Question: Explain the working of SMPS with neat diagram?


Question: Explain the working of hydrogen fuel cell.


Question: Explain the page translation process in 80386.


Question: What is friend function?


Question: Define following terms


Question: What is file?


Question: Explain any one electrical method for measurement of level.


Question: Define lightweight concrete?


Question: Develop relation between ‘Z’ parameter and transmission parameter .


Question: Explain the process Biomass energy conversion.


Question: Explain with suitable example SQL aggretage functions.


Question: What is generic programming?


Question: Describe the following systems in renewable energy system.


Question: What are fractals?


Question: Explain what you understand by A.


Question: The life time of a certain component has a normal distribution with mean of 400 hours and standard deviation of 50 hours.


Question: Derive an expression for line to neutral capacitance of three phase overhead line with unsymmetrical spacing of conductors.


Question: Define Project Scheduling.


Question: Describe the advantages of hydroelectric power plant.


Question: Let  7,1 3 XB  be the Binomial distribution with parameters n = 7 and p = 1/3. Then   25 px px   is


Question: Discuss the methods of synthesis of furan and pyrrole.


Question: What are Micro instructions? Draw and explain micro-programmed control unit design.


Question: Derive an equation for length of cross belt drive.


Question: What are the symptoms and diagnosis of distress of concrete?


Question: Explain types of densitometers.


Question: What are the different types of appraisals required to undertake any Project?


Question: What is the difference between dielectric material and insulating material?


Question: Explain the structure of a V86 Task in detail.


Question: An orifice meter with orifice diameter 15cm is inserted in a pipe of 30cm diameter the pressure difference measured by a mercury oil differentialmanometer on the two sides of the orifice meter gives a reading of 50 cmof mercury.


Question: What do you mean by triangulation and trilateration in geodetic survey?


Question: A Vertical vessel with a cylindrical shell and hemispherical heads is to be installed in a closed shed.


Question: What are the measure of query cost?


Question: Show that (Any one):


Question: List and explain four common examples of exceptions.


Question: A 2m long column has a circular cross section of 6cm diameter.


Question: Explain voltage to current source transformation.


Question: Draw a neat diagram of fluidized bed type catalytic cracking process.


Question: Calculate the heat of reaction at 298.


Question: Explain in detail the working of square wave generators with a neat circuit diagram.


Question: Explain the various losses in transformer?


Question: What is a two port network?


Question: What are polar plots?


Question: Write down paper characteristics.


Question: State the following properties of fourier series.


Question: Derive an expression for capacitance of three phase line when conductors are unsymmetrically spaced but transposed.


Question: List and explain the different metrics in the process and project domain.


Question: Determine the deflection and slope at the free end of cantilever beam of span ‘ l’ m, loaded with central point load ‘w’ kN.


Question: Enlist non destructive tests for concrete.


Question: Draw and explain the general structure of PLA.


Question: Define the following terms.


Question: Explain the operation of SR flip flop with truth table.


Question: Explain the working of PV Cell and Simplest Equivalent Circuit for a Photovoltaic Cell.


Question: Define Industrial Engineering.


Question: State any six properties of Fourier Transform.


Question: Write a note on lapping process.


Question: Explain the procedure for finding slope and deflection for a cantilever beam with a point load at free end Double integration method.


Question: Describe the process of using the STL algorithms for Quick sort.


Question: Convert the following expression from Infix to Postfix expression.


Question: State the types of timers.


Question: What are different types of memories?


Question: Velocity of slider D and angular velocity of link CD.


Question: Draw and explain the interfacing diagram of DAC0808 with PIC18FXX microcontroller.


Question: Find the multiplicative Inverse of 37 mod 26 using Extended Euclidean Algorithm.


Question: What is thermal bimetal?


Question: Find the inverse Laplace transform of given network given F( s).


Question: What observations and precautions are necessary during Core Drilling for Preliminary Geological Exploration?


Question: Draw the connection diagram of shunt.


Question: Define the following terms w.r.t PLL.


Question: Explain with neat sketch tube drawing process.


Question: Determine slope and deflection for a simply supported beam loaded as shown below.


Question: Explain the working of Pirani Gauge for measurement of pressure.


Question: Discuss the mechanism of E1 and E2 reaction of alkyl halides.


Question: Solve the differential equation ()() ()3dy tytx tdt+= for input ()()2txte u t-= . Assume zero initial conditions.


Question: What is powder Metallurgy?


Question: Explain working of vertical type wind turbine with neat diagram.


Question: Explain UP Counter and DOWN Counter.


Question: A 6pole DC motor with wave connected armature has 87 slots with 6 conductors per slot.


Question: What is voltage regulator?


Question: What are different types of inheritance supported by Java.


Question: Write a difference between procedural and object oriented programming.


Question: Draw a neat sketch of broach and name its different parts.


Question: Write down the causes and consequences of acute pancreatitis.


Question: Explain the working of armature controlled D.


Question: Explain the working of Digital to analog converter.


Question: Evaluate ˆ.


Question: Explain Intel i860 processor with block diagram.


Question: Explain with neat diagram how is Lissajous pattern used for phase measurement?


Question: What are the qualities of good drug?


Question: State various obstacles in setting out curves.


Question: Explain the Gauss Elimination method used for the solution of the linear simultaneous equation.


Question: From the given traversal construct the binary tree.


Question: SO2 is absorbed in water using a packed column operated at constant T and P.


Question: Compare DFS and BPS.


Question: Implement a full-adder using Demultiplexer.


Question: Compare SLL with DLL?


Question: Explain influence of geological conditions on the choice and type of dam.


Question: Explain following instruction used in C languages.


Question: Write a short note on Ocean thermal energy conversion.


Question: Design low pass first order Butterworth filter having cut off frequency 1 kHz with  passband gain of 2.


Question: Explain Gibbs phase rules for metallurgical application?


Question: Consider the following processes where arrisal and barst time are as given below. Calculate the average waiting time and average turn aroundtime if the processes are scheduled using FCFS.


Question: Explain method overriding with a suitable example program.


Question: Discuss any three terminology related to psychometric.


Question: Explain with neat circuit diagram working of inverting precision full wave rectifier with its waveform.


Question: A PIC 18 is connected to the 4MHz crystal oscillator.


Question: Explain the working principle of McLeod low pressure vacuum gauge. With neat sketch.


Question: A 250 V DC shunt motor with armature resistance of 0.


Question: Explain PI and PD controller in brief with suitable examples.


Question: What is software quality?


Question: Discuss the working of thermocouples using seebeck effect with diagram.


Question: What are the advantages of Digital Storage oscilloscope over Dual Trace oscilloscope.


Question: In a magnetic material, hysteresis loss is 150 W when maximum flux density of 1.3 tesla and frequency is 50 Hz. What would be hysteresisloss if flux density is decreased to 0.8 tesla and frequency is increased to 60 Hz? Assume that hysteresis loss is proportional to (B m)1.7.


Question: State the difference between character and byte stream in Java.


Question: State the objectives of supercharging of engine.


Question: Draw neat diagram and waveforms of single phase half wave rectifier with resistive load.


Question: With the help of neat diagram explain working of symmetrical schmitt trigger?


Question: Explain any three operations on sequential file organization with example.


Question: The principal tensile stresses at a point across two perpendicular planes are 100 MPa and 50 MPa.


Question: Write note on automated assembly line for car manufacturing.


Question: Calculate the machining time required for 3 passes while reducing 60 mm diameter shaft to 50 mm diameter for a length of 1200 mm with depth ofcut of 2 mm for rough cut and 1 mm for finish cut.


Question: What is call gate?


Question: Differentiate between Relation and functions.


Question: A crude oil of viscosity 0.


Question: With suitable circuit diagram explain no load and blocked rotor test on 3 phase induction motor.


Question: Find the expected value of the sum of the faces obtained when two fair dice are tossed simultaneously.


Question: Draw and explain detail block diagram of hardwired control unit.


Question: Explain flow duration curve and hydrograph with example.


Question: Write an algorithm for evaluating  a postfix expressioin using stack.


Question: Explain with suitable example the three storage structures for the graph.


Question: Write short note on applications of recorders.


Question: Compare SSB and VSB.


Question: Write a short note on Geothermal energy.


Question: Explain various specification of ADC.


Question: The postorder and inorder traversals of a binary tree are given below.


Question: Explain the factors for selection of motor for an EV .


Question: Evaluate  Sxiy j z k d s   over the surface of sphere 22 21 xyz


Question: Define the following terms with example with respect to Binary Tree:


Question: Explain the difference between array representation and linked representation of binary tree.


Question: Draw a neat diagram of DSO.


Question: What is filter medium?


Question: Explain with example hash functions.


Question: What is an identity element in Group?


Question: Describe the characteristics of an entrepreneurship.


Question: Describe Ram type Injection molding with sketch.


Question: What is Backface?


Question: Consider the following processes arrival time and burst time are as shown.


Question: A Cantilever beam of span 2.


Question: Explain role of telecommunication.


Question: Give the applications of Two Port Network Parameters and Explain Network Stability.


Question: What do you mean by excitation table of flip flop?


Question: What is the significance of coating on the material properties?


Question: Draw the phasar diagram of 3 phase induction motor.


Question: Determine the vertical displacement of the joint C of the pin jointed frame as shown in figure below.


Question: Describe Exception.


Question: Derive the expression for loop inductance of single phase overhead lines.


Question: Write Note on ‘Electric Vehicles’


Question: Define PDF and CDF.


Question: Explain the working of Half wave Precision Rectifier with appropriate equations.


Question: What is Exception handing? How to handle Exception in Java?


Question: Write down the steps to be followed to transfer a data serially using 8051 microcontroller.


Question: Explain working of IC 555 astable multivibrator.


Question: Explain the following parameter of OP-AMP


Question: A doubly linked list with numbers to be created.


Question: Explain with a neat diagram winter air conditioning.


Question: Index for 87 divisions by compound indexing using following Brown and Sharpe Plate.


Question: What are the factors affecting on Price Determination?


Question: Write a python program to create a linked list and perform operations on the list.


Question: What are the file access methods?


Question: Distinguish between DM and ADM.


Question: Describe the following sytesm in renewable energy system.


Question: The input to 3 phase, 6 pole, 50 Hz, induction motor is 47 kWatt at certain load. The stator losses are 1.5 kWatt and mechanical losses are1k Watt. Determine the HPoutput power of motor when it runs at 970rpm. (Take 1 HP = 746 watt)


Question: Explain the change control mechanism in SCM.


Question: Define Graph.


Question: Design a Francis turbine runner with the following data.


Question: A box contains 100 bulbs out of which 10 are defective.


Question: Define polymorphism?


Question: What is height balanced tree?


Question: Explain different four types of flows in open channel.


Question: What are sound displays in Virtual Reality?


Question: Explain types of queues. Write any one in detail.


Question: Draw drain characteristics of for n channel JFET.


Question: What is time constant?


Question: State three types of resistance welding.


Question: Explain Black box testing with its advantages.


Question: What are the innovation challenges in design thinking.


Question: Explain Triadic curve and give its fractal dimension.


Question: Find Z parameters of the network shown in figure no.


Question: Write a program that returns the size in bytes of a program entered on the command line.


Question: With suitable block diagram explain working of electronic energy meter.


Question: Discuss the feasibility of dam site, with dipping and horizontal strata.


Question: Explain in brief the mesh selection criteria for screen printing applications.


Question: Explain generation of sine waveform using OPAMP. Draw input & output wave froms


Question: Explain Vacuum forming in Plastics.


Question: Explain the six regimes of the pool boiling curve with the help of a neat diagram.


Question: Explain the construction and working principle of universal motor.


Question: Enlist  various linear methods of setting out curves and explain any one with sketch.


Question: What are the salient features of Green Building?


Question: Draw and explain block diagram of PLC.


Question: Explain Normal combustion and abnormal combustion Phenomena in SI engine.


Question: Draw the flow sheet for manufacturing of Cemented Carbide.


Question: Explain principle of resistance welding with neat sketch.


Question: Prove that expression for laminar flow of fluid.


Question: Explain Reynolds Number with example.


Question: State the necessity of FRL unit in Pneumatic System.


Question: Enumerate the selection of motors depending on load characteristics.


Question: Write a note on elements of a Configuration Management System.


Question: What is cost of quality?


Question: A cast iron pipe of internal diameter 450 mm is 15 mm thick and is supported on a span of 8 m.


Question: Enlist the advantages and disadvantages of DLL over SLL.


Question: Explain in brief a manufacturing process of urea from ammonium carbamate.


Question: Explain with neat diagram 2 input CMOS NOR gate.


Question: What are various types of welding joints used in pressure vessels?


Question: What are the applications of Animal Cell Culture?


Question: List and explain the necessary and sufficient conditions for Hamiltonian and eulerian path with suitable examples.


Question: Draw neat circuit diagram and explain voltage follower.


Question: What is design pattern?


Question: How are Hydroelectric power plants classified?


Question: Determine maximum slope and deflection for a simply supported beam shown in figure below.


Question: What are Packages and Interface in Java.


Question: Explain Interfaces in Linux.


Question: Describe the cold and hot weather concreting.


Question: Demonstrate the various types of chips formed during metal cutting.


Question: Draw and Explain working of SCR.


Question: Elaborate about enabling and disabling interrupts in 80386.


Question: Describe the types of wind turbine electrical generators.


Question: Differentiate between Terrestrial photogrammetry and Aerial photogrammetry?


Question: Discuss the steps in executing interrupts in PIC 18 microcontroller.


Question: What do you mean by network crashing?


Question: Explain linked organization with respect to file handling.


Question: Compare React JS and Angular JS and Vue JS.


Question: An oil of specific gravity 0.


Question: A riddle is given to three students to solve independently.


Question: Explain the working of PV cell and simplest Equivalent Circuit for a photovoltaic Cell.


Question: Differentiate between Orthographic Projection and Isometric Projection.


Question: With suitable diagram explain constructional details of 3 phase slipring induction motor


Question: The bar has a diameter of 40mm.


Question: Explain the rules for constructing the ladder diagram of PLC.


Question: Explain the various methods of speed control of Dc series motor?


Question: Explain briefly EDM process characteristics.


Question: Elaborate the Postfix evaluation algorithm stepwise.


Question: What do you mean by section modulus?


Question: What is mean by composites?


Question: Depict the figure showing he feeder pathways for glycolysis.


Question: Determine capacitance per phase per km of three phase transmission line when conductors are arranged in horizontal plane and 4 meter apart.


Question: Enlist various types of residential buildings and explain any one in detail.


Question: Draw and explain characteristics of LVDT.


Question: Draw and explain the Backward feed multiple effect evaporator.


Question: Discuss the merits of circular queue over linear queue and write sudo code for over flow and under flow conditions of circular queue.


Question: What is 2D rotation of an object about an arbitrary point?


Question: What is voltage regulator? Write any two applications of voltage regulator.


Question: What is Design?


Question: Find maximum flow in the transport network using labeling procedure.


Question: State the types of starters used for induction motors.


Question: Derive the expression for attenuation constant and Phase shift of proto type constant K high pass filter.


Question: Explain addressing modes of 8086.


Question: Write short note on RS232 standard.


Question: State the following properties of DT fourier series.


Question: Discuss briefly energy band in conductor and insulator.


Question: Draw the router architecture.


Question: Write a program to turn off LED for connected to Port 0 when interrupt 0 occurs and turn it on when interrupt 1 occurs.


Question: To find out coefficient of permeability of clay the permeability test was carried out in a variable head permeameter having the diameter of thesample container to be 100 mm.


Question: A rectangular block of material is subjected to stresses on perpendicular faces as shown in figure 4.


Question: Explain fluidization with its type and application?


Question: Explain interrupt structure of 8051 microcontroller with neat diagram.


Question: Write a program in C to configure Port 1 as input port and Port pin P2.


Question: Write limitations of arrays over linked list?


Question: Convert the following infix expressions to prefix expressions using stock.


Question: Derive an expression for the capacitance to neutral of a three phase line with equilateral spacing.


Question: Explain in detail distortion in delta Modulation.


Question: Discuss Link State Routing protocol in detail.


Question: Distinguish between buckle and knife folding mechanism with suitable diagram.


Question: Explain Memory Partitioning in memory management.


Question: Two straights PI and QI meet at chainage of 1250 m. A right handed simple circular curve of 250 m radius joins them. The deflection anglebetween two straights is 30 °. Tabulate the necessary data to layout the curve by Offset from long chord. Take chord interval as 10 m.


Question: Explain practical differentiator circuit with neat circuit diagram. What are the limitation of ideal differentiator.


Question: Distinguish singly linked list and doubly linked list.


Question: Give the properties and application of Manganin.


Question: Consider the following page reference string A,B,C,D,A,B,E,A,B,C,D,E. Calculate page fault with FIFO page replacement algorithm when framesize is 4.


Question: With neat diagram explain working of IC 555 as a Monostable Multivibrator.


Question: Find the Fourier Transform of a constant signal AO.


Question: Explain the working of diaphragm type elastic pressure transducer. With the help of diagram show. how strain gauges are mounted on it.


Question: What is Software Architecture?


Question: Design an adjustable voltage regulator using LM 317 for output voltage from 10 to 20 V and draw the typical connection diagram.


Question: List and explain file types and file access methods.


Question: Explain various rules for development of Ladder diagram.


Question: Explain segment address translation in detail.


Question: Enlist and explain Component level design steps in detail.


Question: What is operator overloading?


Question: Explain Steps to transfer Data Serially in 8051 microcontroller.


Question: What is VHDL?


Question: Explain in brief various retrofitting techniques used to strengthening RCC column and beams.


Question: Explain Edge connectivity and Vertex Connectivity with suitable example.


Question: What is fold?


Question: Derive Trapezoidal rule for numerical integration as a special case of Newton’s Cote formula.


Question: Explain the supercharging with neat sketch.


Question: A dice is thrown 10 times.


Question: What are the geological requirement for the foundation of dam?


Question: What is navigation and manipulation interfaces in virtual reality system?


Question: Draw a labelled sketch of twist drill and explain its terminology.


Question: Derive expression for the pressure drop for a steady laminar flow through circular pipe.


Question: Explain the architecture of PLC with neat diagram.


Question: Draw and explain general structure of PAL.


Question: Explain in brief the direct screen stencil making process.


Question: What is Socket?


Question: Program the 8051 in C to receive bytes of data serially and put them in P2.


Question: Use Gauss Seidel method to solve the following system of equations


Question: A reaction turbine works at 450 r.


Question: Explain software reuse.


Question: Explain different types of constrained motion with neat sketch.


Question: Solve the heat equation.


Question: Explain Normal combustion and abnormal combustion Phenomena in SI engine.


Question: Define the components of LINUX system with diagram.


Question: Use the Gauss Jordan method to find the inverse of the following matirx.


Question: Write an algorithm for searching an element using Fibonacci search method.


Question: Evaluate by Gaun divergence theorem333.


Question: Write short note on Interrupt enable register.


Question: Define the different categories of risks?


Question: Explain in detail the working of dynamometer types wattmeter with a neat diagram. Also, state its advantages and disadvantages.


Question: What is the significance of pressure boosters and elaborate pressure booster in brief.


Question: Explain a ‘C’ function to Insert node in singly linked list.


Question: What is containment?


Question: Explain operating characteristic of centrifugal pump?


Question: What is a solar collector?


Question: Explain the behavioral modeling in Virtual Reality.


Question: Discuss the design procedure of spur gears.


Question: State  any one application of-


Question: Why 3 phase induction is also called as generalised transformer?


Question: Write a short note on sequential memories.


Question: Show that analytic Function with constant modulus is constant.


Question: A 4m length of a tube has a buckling load of 2kN when used as a column hinged at both ends.


Question: Convert the following infix expressions to postfix and show the contents of stack for each operation.


Question: Acircular cantilever beam of span 4Meter is subjected to a point load of 2KN at free end.


Question: What is logic family?


Question: List the differences between CMOS and TTL logic family.


Question: Write a short note on IC LM 317.


Question: Find bilinear transformation which maps the points 1, i, –1 of z-plane onto the points 0, 1, ∞ of w-plane.


Question: What is a biodegradable polymer?


Question: Derive torque equation of induction type energy meter with usual notations.


Question: Explain construction and principle of working of Centrifugal pump.


Question: Explain the method of reducing cutting forces in sheet metal work.


Question: Comment on flashing in brief and suggest the suitable method used to reduce it.


Question: What is namespace?


Question: The average rate of inflow during 12 months for a river are as under


Question: Which are the common magnetic materials?


Question: Write a note on necessity and types of transition curves.


Question: Describe various types of unconformities with neat sketches.


Question: What is viscosity of ink?


Question: Draw and explain Cluster and Cluster Architectures.


Question: Determine the Fourier transform of the following continuous time signals.


Question: State different uses of contour maps?


Question: Explain following QC tools.


Question: Explain significance of any three dimensionless numbers used in various modes of heat transfer for thermal analysis.


Question: Write a program in C language to configure timer 0 of 8051 microcontroller in mode 2 use 8051 XTAL for clock source and start the timer 0.


Question: What are the responsibilities of a safety manager on construction sites?


Question: Explain the construction and operation of permanent magnet stepper motor.


Question: Write algorithm for posfix expression evalution.


Question: What is TDR in constrution?


Question: Differentiate between static and dynamic memory allocation.


Question: Explain Filament winding Composite manufacturing process.


Question: Explain Ammonia synthesis converter with a neat figure.


Question: Explain design evaluation cycle.


Question: What is B tree?


Question: Explain the working of PV cell and Simplest Equivalent Circuit for a Photovoltaic cell.


Question: Explain reading  character and string from input console with suitable examples.


Question: State two features each of LAP winding and WA VE winding for DC machine.


Question: Explain geometrical isomerism in compound with one double bond.


Question: Classify solid insulating materials according to the temperature ranges. Hence write properties and applications of any two materials from ClassA type.


Question: Explain multistage compression of reciprocating air compressor.


Question: Write short note on.


Question: Illustrate with neat sketches common types of welded joints.


Question: A solid cylindrical shaft is required to transmit 600 kW at 110 rpm.


Question: Give detail classification of Heat Exchanger.


Question: Draw and explain the interfacing diagram of strain gauge with Arduino Board showing necessary subsystems.


Question: What is polymorphism?


Question: Give any two points of comparison between LAP winding and WA VE winding for DC machine.


Question: What is DNS?


Question: Give the Dirichlet conditions for Continuous time Fourier Series.


Question: Draw and explain successive approximation A/D converter.


Question: Write in detail about Cori cycle.


Question: Explain the significance of a file.


Question: What are the advantages and disadvantages of TBT?


Question: Explain the Bezier curve.


Question: Evaluate following postfix expression with the help  of stack.


Question: What is Decision Support system?


Question: Explain coordinate system with types in brief?


Question: Obtain the line of Regression of y on x for the following data.


Question: Write a program in C language to enable hardware interrupts INT0 and INT1.


Question: Elaborate Advantages and Disadvantages of LIST Sequential Container.


Question: Draw & explain the working of inclined tube manometer? Give the reason for its higher sensitivity.


Question: State and prove sampling theorem with suitable waveform and mathematical expression?


Question: Compare SRAM and DRAM.


Question: Describe the historical development of wind turbine on Indian level.


Question: Explain screw thread terminology.


Question: Explain with appropriate example how schedule can be prepare using PERT.


Question: Explain in detail corrosion monitoring technique for reinforcement and preventive measures against corrosion.


Question: A solution of 3.


Question: What is accelerometer?


Question: Explain with a neat diagram winter air conditioning.


Question: What is the space complexity of threaded binary tree.


Question: Explain various stages of combustion in S.


Question: Compare open loop and closed loop control systems.


Question: Enlist various traps including its functions.


Question: What is dimensionality reduction?


Question: What is operator overloading?


Question: In the circuits in Fig. 2. The switch is closed at  t = 0.


Question: Explain necessity of transposition of line conductors in three phase lines.


Question: Probability of man aged 60 years will live for 70 years is 1 10.


Question: Classify continuous control modes used in process control system and explain PID controller with suitable example.


Question: Explain the construction of three phase induction motor?


Question: Explain how koch curves are generated.


Question: Define indegree and outdegree of a vertex in graph.


Question: Explain in brief the Characteristics of memory systems.


Question: Explain brief classification of I.


Question: Explain how synchros can used as Error detectors.


Question: What is Microprocessor?


Question: Explain digital control system in detail.


Question: Explain on the Psychrometric Chart following Processes.


Question: Discuss “Swedish Slip Circle Method” for stability analysis of finite slope.


Question: Explain SMPS with block diagram.


Question: What is indexing?


Question: Explain in brief the importance of preliminary geological exploration in civil engineering project.


Question: Define CDF and state any four properties of CDF.


Question: Explain block diagram of digital computer.


Question: Explain the Pneumatic power supply with neat sketch.


Question: What are the salient features of Green building?


Question: Explain in brief four color separation method for screen printing process.


Question: A three span continuous beam ABCD is loaded with ultimate loads as shown in figure 11.


Question: Draw and explain the interfacing diagram of DAC0808 with PIC18FXXX.


Question: Explain FM generation by Armstrong method with neat block diagram.


Question: Draw and explain Ring Counter.


Question: What is Real Time Operating Systems?


Question: Explain with appropriate example the feasibility of dam alignment which is crossing DYKE.


Question: Write down the steps in executing on an interrupt.


Question: Explain model for network security.


Question: Discuss with an example what is forward reference problem.


Question: What are the different types wet sump lubrication system and explain any one of them.


Question: A 6 pole, 3 phase induction motor is connected  to 400 volt, 50 Hz ac supply. Calculate- i) the speed of rotating magnetic field of the motor ii) Speed of motor at 3% slip iii) the ro tor emf frequency at 3% slip


Question: Explain the factors affecting Compaction of soil.


Question: If ()2 2V4xyx y=−  is harmonic find its harmonic conjugate and determine F( z) in terms of z.


Question: Describe molecular machines with neat diagrams.


Question: Explain in brief wet and dry lamination methods.


Question: Explain Linux thread management in detail.


Question: Draw and explain the working of a Digital kilo watt Hour Meter.


Question: State and explain the conditions for deadlock to occur.


Question: What are types of acceleration?


Question: Following are the details of Project A and B.


Question: What are the problems in RIP?


Question: Find the expected value of the number of heads obtained when three fair coins are tossed simultaneously.


Question: What is Koch curve?


Question: Give types and applications of stepper motor.


Question: The velocity component of 2D flow field are as follows.


Question: Enlist the factors affecting tool life.


Question: A coil which has an inductance of 40mH and a resistance of 2  is connected to form an LR series circuit. If they are connected to a 20VDC supply. Find


Question: Obtain the expression for current flowing through Inductor in series RL circuit and voltage across capacitor in series RC circuit connected to a d.


Question: What is the difference between analog instruments and digital instruments?


Question: Write short note on SPI protocol.


Question: What are Pumps and Compressor used in Hydraulic and Pneumatic Systems?


Question: Compare CMOS and TTL logic family.


Question: Draw the block diagram of LM317 and explain in detail.


Question: Draw and explain in detail Pool boiling curve with significance of each point in the pool boiling.


Question: State and write properties of electrical carbon materials and materials used for Lamp Filaments.


Question: Explain hydrograph and flow duration curve with example.


Question: Find the angle between the tangents to the curve


Question: What are the fundamental requirements of residential building?


Question: Explain speed control using v/f method.


Question: Vector along the direction of the line.


Question: Solve, ()( )( ) 26 19 2 ,kfk fk fk++ + + =  if () ( )01 0ff == .


Question: Show that.


Question: Explain the contents of Projet Feasibility report with example.


Question: A bank maintains two kinds of accounts for customers.


Question: What is Radiation?


Question: If .


Question: What is fourier series.


Question: Write short note on:


Question: Explain with block diagram virtual instrumentation.


Question: For the Inverting Schmitt trigger shown in fig.


Question: Explain with sketch the fixed hair method of tacheometry, when line of sight is inclined downward (depression) and staff is held vertical?


Question: Draw and explain General Selector Format.


Question: What are different mechanisms of polarization?


Question: What methods are used to measure microbial population.


Question: Compare active filters and passive filters.


Question: Explain grid connected renewable systems and their requipments.


Question: Explain following pins of 8051.


Question: Explain micro operations of CPU.


Question: Describe Material Extrusion process in short.


Question: Explain the Gauss Elimination method used for the solution of the linear simultaneous equation.


Question: Explain necessity of nitrogeneous fertilizers produced from Ammonia.


Question: Explain the properties of line codes.


Question: Derive the relation of power in wind and explain impact of tower height on power generation in wind  energy system.


Question: Compare index sequential file and direct access file.


Question: Explain 3 position relative pole method for synthesis of four bar chain mechanism.


Question: Compare between Thermosetting plastic and Thermoplastic plastic.


Question: What is Age Hardening.


Question: Write a short note on Saytzeff rule.


Question: Draw and explain the ARM family core architecture.


Question: Derive an expression for flux linkages due to signle current carrying conductor.


Question: What is mean by Constructor?


Question: What is meant by reactance voltage in case of commutation in DC machine?


Question: Obtain y-parameters of two port network for the given network in the fig.7.


Question: Find minimum spanning tree for the following graph using Prim ’s Algorithm.


Question: Apply the block digram reduction rules to reduce the following system into canonical form and determine its control ratio.


Question: What do you mean by limit of proportionality or elastic limit?


Question: Explain Additive colour theory and subtractive colour theory.


Question: Explain various features of the 8051 Microcontroller.


Question: Discuss following terms.


Question: Prove that 242( )(l o g ) () .ba a rba r b rrr    


Question: Draw neat diagram of 3 phase FWR with R load.


Question: Draw single circular linked list with 5 nodes.


Question: Use labeling procedure to find a maximum flow in the transport network given in the following figure.


Question: Describe any two component which can be manufactured by only powder metallurgy technique.


Question: Explain in details various types of Relays and Electric Encoders used Printing Industries.


Question: Derive the relation between unit step function and unit ramp function.


Question: How Defects are managed?


Question: A bolt is subjected to an axial pull of 40 KN and a transverse shear force of 15 KN.


Question: Write sudo code for inserting a node in binary search tree.


Question: Discuss in detail the studies to be carried out in reservoir areas of a dam.


Question: Construct heap data structure to sort the following set of no.


Question: What is software SCM repository?


Question: Explain the construction and working of linear induction motor with the help of suitable diagrams.


Question: Illustrate negative indexing in list with an example.


Question: What are the classification of transducers? Explain any 2 in detail.


Question: Describe the software quality dilemma in your own words.


Question: Explain different types of flames with neat sketches in gas welding process.


Question: What are the Components of pneumatic and hydraulic systems?


Question: What are different Process management system calls in Linux.


Question: A three hinged parabolic arch having supports at different levels as shown in figure 6.


Question: Explain the project management life cycle.


Question: Write Short notes on industrial robotic application of Light Curtains and Laser Area Scanner.


Question: What is the need of electric vehicle?


Question: Find the slope of the free water surface in a rectangular channel of width 20m having depth of flow 6m.


Question: Discuss factors affecting the durability of concrete.


Question: Write a Java program to accept values inside the multidimensional array.


Question: Explain the Standard Marking System of a grinding wheels.


Question: Draw the block diagram of a regulated dc power supply and explain the function of each block in it.


Question: Explain with suitable example BSF and DSF traversal of graph.


Question: What is multithreading?


Question: Explain Linked List class with an example.


Question: Explain ‘Core of the Section’ and obtain a core section for a hollow circular column of external and internal diameter ‘D’ and ‘d’ respectively.


Question: Explain the function of 78XX and 79XX voltage regulator.


Question: List down and explain in brief the screen frame purpose and requirement.


Question: Sketch the polar plot for.


Question: What are types of memory fragmentation?


Question: Write short note on design activism.


Question: Compare single phase HWR and single phase FWR.


Question: Explain the following file organization techniques.


Question: If three coins are tossed.


Question: What is the ambiguity that arises in multiple inheritance?


Question: A trapezoidal channel has side slope of 3 horizontal to 4  vertical and slope of its bed is 1 in 2000. Determine the optimum dimensions for thechannel sections and show it with neat sketch, if it is carry water at  0.55m 3/s. Take Chezy’s constant as 80.


Question: The Connective tissue connects and supports the entire human body.


Question: State any four applications of DC Series motor.


Question: Explain the use of profile projector with neat sketch.


Question: Draw and explain the interfacing of LCD with Port D and Port E of PIC18FXX microcontroller.


Question: Explain various socket primitives used in connection oriented client server approach.


Question: Write a short note on thermocouple.


Question: Obtain regression line of the following data.


Question: What are the different laws of Radiation?


Question: What are the assumption of BET theory of adsorption?


Question: Explain the following concept.


Question: Write algorithms to create and delete a segment.


Question: Derive the relation between heat of reaction at constant pressure and at constant volume mentioned the three case of it.


Question: Derive the expression for a minimum number of teeth on gear wheel required to avoid interference with neat sketch.


Question: Explain applications and selection criterion of valves in robotics and automation systems.


Question: Define stack as an ADT.


Question: Calculate ABCD constants for three phase 50 Hz transmission line with following line parameters.


Question: What is CAD customization?


Question: Explain the properties of solid insulating material.


Question: What do you mean by:


Question: What is semiconductor memory?


Question: Discuss in detail preliminary geological investigations of tunneling.


Question: Write a short note on survey for drainage line work?


Question: Explain carnot cycle with neat diagram.


Question: Write down a C++ program for copy constructor for string class.


Question: Difference between Rankin cycle and Carnot cycle.


Question: Discuss various types of flow with example.


Question: What is file mode?


Question: A tightly stretched string with fixed ends x = 0 and  x = l is initially at rest in its equilibrium position is set to vibration by giving each point a velocity 3x(l – x) for 0 < x < l. Find the displacement y(x, t) at any time t.


Question: Define Basic work content.


Question: Explain the various factors affecting corrosion.


Question: What is landslides? What are the causes of it?


Question: Write a note on Embedded and Dynamic SQL.


Question: Enlist the documents to be submitted for seeking commencement certificate and occupancy certificate.


Question: Why chucks are used?


Question: What is fire escape and explain any one fire escape elements?


Question: Explain the concept of current mirror circuit?


Question: Explain the various types of errors that take place in wattmeter.


Question: Explain how the verticality of tall building is checked?


Question: Explain the internal diagram of IC 7490.


Question: A centrifugal pump having outer diameter equal to two times the inner diameter and running at 1000 r.


Question: Explain the working of functional block diagram of IC 555 Timer.


Question: What is mean by Governing system and explain all types of governing systems?


Question: An infinitely long uniform metal plate is enclosed between lines y = 0, and y = l for x > 0. The temperature is zero along the edges y = 0, y = l, and at infinity. If edge x = 0 is kept at a constant temperature 0,v Find the temperature distribution ,.vxy


Question: Use fourier transform to solve.


Question: Differentiate Between Flame Hardening and Induction hardening.


Question: What are the salient features of vegetable market building.


Question: Explain effective diameter measurement by three wire method.


Question: Explain in detail with Diagram.


Question: Draw and explain the Von Neumann architecture.


Question: Explain screw compressor with neat sketch.


Question: Determine the principal stress in the beam at point A.


Question: Explain the difference between standard concrete and special concrete.


Question: Draw and explain Block diagram of an adjustable three terminal positive voltage regulator.


Question: Differentiate between brass and bronze.


Question: Derive with usual notations the following Darcy-Weisbach equation for the loss of energy due to friction.


Question: Solve the following integral equation,


Question: Describe SIMO chart with suitable illustration and appropriate symbols.


Question: What are the considerations for natural lighting in a residential building?


Question: Explain with the help of neat block diagram Armstrong method of FM generation.


Question: Define ceramic materials.


Question: Explain in details Core Less type Induction Furnace.


Question: Let I be the set of all integers.


Question: An aptitude test for selecting officers in a bank conducted on 1000 candidates.


Question: With the help of neat sketch explain single block brake.


Question: Find slope at supports and at point ‘C’, deflection at ‘C’ and ‘D’ for the given beam using Macaulay’s method.


Question: Explain Welding Inspection briefly.


Question: Explain functioning of LM 317 as a voltage regulator.


Question: Differentiate between distance vector and link state routing.


Question: A 250 mm wide strip of 27 mm thickness is reduced to 24 mm in a single pass through a rolling process.


Question: Derive the expression for minimum starting speed of a centrifugal pump.


Question: What are major and minor losses?


Question: Explain the significance of phosphorylated intermediates in glycolysis.


Question: What is concurrency control?


Question: Explain the standard characteristics of TTL in details.


Question: i) Explain the Specific energy curve with neat sketch.


Question: Assuming crystal frequency of 11.


Question: A solid circular shaft transmits 220 kW at 160 rpm. The maximum allowable shear stress is 60 MPa and angle of twist permitted is 2º in 3mlength. Design suitable shaft. Take G = 78 GPa.


Question: A 200 V lap wound DC shunt motor has 800 conductors on its armature.


Question: Calculate the heat transfer from 60 W from incandescent bulb at 115ºC to ambient air at 25ºC.


Question: Explain the applications of applied geometric algebra for modelling of robotics physics.


Question: What are the elements that exist when an effective SCM system is implemented?


Question: Explain any two mineral deficiencies in detail.


Question: Draw and Explain circuit of an IGBT.


Question: What are components of ASM chart?


Question: Draw and discuss the motion balance system.


Question: Write a python program to create a queue class using list methods.


Question: Draw the sketch of Window.


Question: A 230 V .


Question: Give principle and instrumentation of flame photometry.


Question: Derive the expression for F.O.S. for dry infinite slope in sandy soil.


Question: Derive the relationship between the mole fraction of components taking part in the reaction and the extent of the reaction.


Question: Explain the applications of Bezier curves in robot path planning.


Question: With suitable block diagram explain working of static energy meter.


Question: Compare direct and indirect methods of subsurface geological investigations.


Question: Construct the binary search tree (BST) from the following elements:


Question: Write a C function to insert a node into a singly linked list.


Question: Write an explanatory note on rotary drum filter.


Question: Compute GCD of the following using Euclidean algorithm.


Question: Explain in detail pipeline performance.


Question: Explain the addressing modes of 8051 Microcontroller with examples.


Question: Two identical soil specimens were tested in a triaxial apparatus. First specimen was failed at a deviator stress of 700 kN/m2 when the cell pressure was 200 kN/m2. Second specimen was failed at a deviator stress of 1300 kN/m2 when the cell pressure was 400 kN/m2. Determine cohesion of soil and angle of internal friction of soil analytically.


Question: What is hybrid screening with its advantages.


Question: What are homogeneous transformations of coordinates?


Question: How is the equilibrium constant K related to the standard free energy change?


Question: Syphon of diameter 200mm connects two reservior having difference in elevation of 15m.


Question: Short note on Optimum proportions of a vessel.


Question: Discuss the properties of line codes.


Question: What are various types of Cast Iron?


Question: Write down the various methods used for prevention of corrosion.


Question: The open loop transfer function of the unity feedback system is 32200G(S)(61 1 S 6 )ss s Using Routh criterion determine stability of the system.


Question: Explain various factors which affects breakdown of solid insulating material.


Question: Write pseudo-micro-steps for the following operations. Register transfer and fetching a word from memory.


Question: What is remote sensing?


Question: What are the effects of the following factors on SN1 and SN2 reactions?


Question: Apply Gauss Jordan method to find inverse of


Question: List the properties of probability.


Question: What is meant by ROM?


Question: Write any four industrial applications of the DC series and DC shunt motor.


Question: Differentiate the microcontroller and microprocessor.


Question: How can vectors and lists be used as sequence containers in the STL?


Question: Write a program to clear 10 RAM locations starting at RAM address 20H.


Question: Describe compading methods -law and A - law.


Question: A hollow shaft 1.


Question: Explain in detail the working and construction of single phase induction type energy meter with a neat diagram.


Question: What is SCM?


Question: Give dimensionless numbers in case of natural and forced convection.


Question: Explain any one type of Cache Mapping technique with diagram.


Question: Explain the instruction Formats in 8086 with examples of suitable instructions. What is Operand? Enlist types of operands.


Question: What are the objectives of testing?


Question: A 4 pole DC shunt generator with lap connected armature has field and armature resistances as 50 Ω and 0.


Question: List out the properties of Laplace Transform.


Question: What is Heat affected Zone?


Question: With the help of pin diagram explain the functions of Operational Amplifier.


Question: Explain mechanical dot gain and factors responsible for the same.


Question: How landslides can be prevented?


Question: The following marks have been obtained by a class of students in 2 papers of mathematics.


Question: Explain in detail TQM and its importance.


Question: Which are the important properties desired from electrical materials?


Question: Compare stacks and queues.


Question: Explain the function of an electromechanical relay and draw an interfacing diagram of relay with microcontroller 8051 with suitable driver circuit.


Question: Find Laplace Transform of the waveform given in Fig No.


Question: An axial pull of 20 kN is suddenly applied on a steel rod 2.


Question: Explain blow moulding with suitable sketch.


Question: Enlist the steps of protein digestion and absorption in stomach and intestine.


Question: State which database architectures you will prefer for following application.


Question: Find the Laplace Transform of periodic wave given below.


Question: Explain the process of Enabling and Disabling Interrupts in 80386.


Question: With neat pin diagram explain function of each pin of IC 741


Question: Explain any two parallel Database System Architecture in detail.


Question: Explain the solidification of pure metal.


Question: What is unconformity and Describe various types of unconformities.


Question: Find the ‘Q’ point for a dual input balanced output differential amplifier with RC = RE = 65 k . supply voltage used is ± 1s V .


Question: Explain the Nitriding process in detail with a suitable diagram.


Question: What is a doubly linked list?


Question: Explain acceleration image principle with neat sketch.


Question: What different operations are carried out on aluminum to make it eligible as plate making material.


Question: Explain the followings terms related to refrigeration.


Question: Describe working of astable multivibrator with necessary diagrams and derivations.


Question: Explain mechanism of universal indexing head.


Question: Find the Fourier cosine integral representation of the function, (),0 0,x xafxxa<<=>


Question: State the types of programming languages and explain any two.


Question: List the properties of distribution function.


Question: Write a short note on Glass and its types.


Question: Explain direct and reverse action for controller in brief with suitable examples.


Question: Explain the term Rescheduling and Updating.


Question: Explain the working of OPAMP as comparator.