Seals
 52. (1) Every Member shall have a seal of a design approved by the Council, the impression of which shall include, (a)  the surname and initials or given names of the Member; (b)  the words “Licensed Professional Engineer”, “ingénieur agréé” or “ingénieure agréée”, and “Ontario”; and (c)  the licence number.  R.R.O. 1990, Reg. 941, s. 52 (1); O. Reg. 13/03, s. 15 (1); O. Reg. 305/18, s. 1 (1). (1.1) If a Member’s seal was issued before February 28, 2003, clause (1) (c) does not apply.  O. Reg. 13/03, s. 15 (2); O. Reg. 81/06, s. 2. (2) Where a Member’s seal was issued prior to the 1st day of September, 1984, the word “Registered” may appear in place of the word “Licensed” on the seal.  R.R.O. 1990, Reg. 941, s. 52 (2). (3) Every holder of a temporary licence shall have a seal of a design approved by the Council, the impression of which shall include, (a)  the surname and initials of the holder of the temporary licence; (b)  the words “Temporary Licensee” or “titulaire de permis temporaire”, and “Association of Professional Engineers of Ontario” or “Ordre des ingénieurs de l’Ontario”; (c)  the temporary licence number; (d)  the date of expiry; and (e)  a statement of the limitations on the temporary licence that may affect the public.  R.R.O. 1990, Reg. 941, s. 52 (3); O. Reg. 305/18, s. 1 (2). (3.1) Every holder of a provisional licence shall have a seal of a design approved by the Council, the impression of which shall include, (a)  the surname and initials of the holder of the provisional licence; (b)  the words “Provisional Licensee” or “titulaire de permis provisoire”, and “Association of Professional Engineers of Ontario” or “Ordre des ingénieurs de l’Ontario”; (c)  the provisional licence number; (d)  the date of expiry; and (e)  a statement that the holder is entitled to practise professional engineering only under the supervision of a professional engineer, and shall not assume responsibility for any activities within the practice of professional engineering unless the professional engineer supervising the holder also assumes responsibility for those activities. O. Reg. 13/03, s. 15 (2); O. Reg. 305/18, s. 1 (3); O. Reg. 837/21, s. 4. (4) Subject to subsection (5), every holder of a limited licence shall have a seal of a design approved by the Council, the impression of which shall include, (a)  the surname and initials of the holder of the limited licence; (b)  the words “Association of Professional Engineers of Ontario” or “Ordre des ingénieurs de l’Ontario” and one or more of the following: (i)  “Limited Engineering Licensee”, (ii)  “titulaire de permis restreint d'ingénieur”, (iii)  “LEL”, (iv)  “PRI”; (c)  the limited licence number; (d)  a statement that the limited licence is limited to the services within the practice of professional engineering mentioned in the limited licence; and (e)  Revoked:  O. Reg. 13/03, s. 15 (3). (f)  a statement of the limitations on the limited licence that may affect the public. R.R.O. 1990, Reg. 941, s. 52 (4); O. Reg. 13/03, s. 15 (3); O. Reg. 71/15, s. 19 (1-3); O. Reg. 305/18, s. 1 (4). (5) In the case of a holder of an engineering technologist class of limited licence, clause (4) (b) does not apply, and the holder’s seal shall instead include the words “Association of Professional Engineers of Ontario” or “Ordre des ingénieurs de l’Ontario” and one or more of the following: 1.  “Licensed Engineering Technologist”. 2.  “technologue en ingénierie titulaire de permis”. 3.  “LET”. 4.  “TITP”. O. Reg. 71/15, s. 19 (4); O. Reg. 305/18, s. 1 (5).