b6Amine/MNLP_M3_quantized_dataset huggingface dataset:
Question: The data address of look-up table is found by adding the contents of
Options:
accumulator with that of program counter
accumulator with that of program counter or data pointer
data register with that of program counter or accumulator
data register with that of program counter or data pointer
Answer: B
Question: For a channel to be economic which of the following parameters should be minimum.
Options:
Wetted perimeter
Wetted area
Section factor
Hydraulic depth
Answer: A
Question: ICMP is primarily used for __________
Options:
error and diagnostic functions
addressing
forwarding
routing
Answer: A
Question: What is the fraction of N2 in purge stream?
Options:
0.04
0.05
0.16
0.4
Answer: C
Question: In an inverting op-amp circuit for which the gain is −4 V/V and the total resistance used is 100 kΩ. Then the value of R1 and R2 (negative feedback)
Options:
R1 = 20KΩ and R1 = 80KΩ
R1 = 80KΩ and R1 = 20KΩ
R1 = 40KΩ and R1 = 60KΩ
R1 = 50KΩ and R1 = 50KΩ
Answer: B
Question: Bakelite is ____________
Options:
Gel
Gas
Solid
Liquid
Answer: D
Question: Identify the sub-process of process improvement
Options:
Process introduction
Process analysis
De-processification
Process distribution
Answer: A
Question: Which one of the following is NOT covered under Taxonomy?
Options:
Alpha taxonomy
Beta taxonomy
Delta taxonomy
Gamma taxonomy
Answer: C
Question: At what conditions does the Coulomb friction occur between the surfaces in contact of collar bearings or pivots?
Options:
When there is no lubricating fluid
When there is no friction fluid
When there is no adhesive fluid
When there is no cohesive fluid
Answer: B
Question: The advantage of static prediction is
Options:
simple and fast
does not require table lookups or calculations
performs without much degradation
all of the mentioned
Answer: D
Question: If the Default operation size bit, D=1, the code segment operation size selected is
Options:
8-bit
16-bit
32-bit
64-bit
Answer: C
Question: In AVR, which of the following registers are used for SPI?
Options:
SPSR
SPCR
SPDR
All of the mentioned
Answer: D
Question: Turn-on and turn-off times of transistor depend on _________
Options:
Static Characteristic
Junction Capacitance
Current Gain
Voltage Gain
Answer: B
Question: Work output of turbine is ____ the work input to the pump.
Options:
much larger
much smaller
equal to
none of the mentioned
Answer: A
Question: The split piece pattern is aligned perfectly using ________
Options:
Screw Pins
Dowel Pins
T-Pins
Straight pins
Answer: B
Question: If five forces are acting on the single particle and having an angle of 72˚ between each and are collinear, then_____________
Options:
The net force acting on the body is zero and the net work done is also zero
The net force acting on the body is horizontal
The net force acting on the body is vertical but net work done is non-zero
The net force acting on the body is at an angle of 45
Answer: A
Question: PPP consists of ________components
Options:
Three (encapsulating, the Domain Name system)
Three (encapsulating, a link control protocol, NCP)
Two (a link control protocol, Simple Network Control protocol)
One (Simple Network Control protocol)
Answer: A
Question: Better atomization and _____________ will make the engine less knock prone.
Options:
ignition
vapourization
condensation
none of the mentioned
Answer: B
Question: In analysis of coal, determination of _______ is done by Kjeldahl method.
Options:
Volatile matter
Nitrogen
Ash
Oxygen
Answer: B
Question: If a force applied at any point in its line of action and is still creating the same moment about any fixed point say P, then the force is said to be a sliding vector. What is the name of this property in a bending moment diagram?
Options:
Associative property
Distributive property
Negative associative property
Principle transmissibility of the force
Answer: A
Question: ___________ is a personalization Web page and tool for Windows Live with status information and navigation features.
Options:
Windows Live Home
Windows Live Gallery
Windows Live Groups
Windows Live Hotmail
Answer: A
Question: The header file setjmp.h is used to __________
Options:
set location specific information
control low-level calls and returns to and from functions
handle signals reported during a program’s execution
manipulate strings (character arrays)
Answer: B
Question: What is the approximate hybrid parameter voltage gain of a CC amplifier?
Options:
1 + hie × Ri
1 – hie × Ri
1 + hie / Ri
1 – hie / Ri
Answer: D
Question: The depletion layer of tunnel diode is very small beacause______
Options:
its abrupt and has high dopants
uses positive conductance property
its used for high frequency ranges
tunneling effect
Answer: B
Question: Which of the following frequencies is not used in WiMAX for communication?
Options:
2.3 GHz
2.4 GHz
2.5 GHz
3.5 GHz
Answer: B
Question: Incorrect information results in unsatisfied preconditions for actions and plans _____________ detects violations of the preconditions for successful completion of the plan.
Options:
Conditional Plan
Conformant Planning
Execution monitoring
Both Conditional Plan & Execution monitoring
Answer: B
Question: Which of the following functions returns a dictionary mapping group names to group numbers?
Options:
re.compile.group
re.compile.groupindex
re.compile.index
re.compile.indexgroup
Answer: B
Question: What is the name of the process where the introns are removed and the exons are joined together in a defined order?
Options:
Trailing
Capping
Tailing
Splicing
Answer: D
Question: What is the formula for rolling velocity?
Options:
ωp x r
ωg x R
0
ωg x r
Answer: A
Question: Which copper alloy is used for making cutlery?
Options:
German silver
Cupronickel
Brass
Bronze
Answer: A
Question: When does a dielectric become a conductor?
Options:
At avalanche breakdown
At high temperature
At dielectric breakdown
In the presence of magnetic field
Answer: A
Question: Evolution of a particular sequence _______ correlate with the evolutionary path of the species.
Options:
does not
always
does not necessarily
invariably
Answer: A
Question: Which of the following is being investigated as a means of automating the creation of a knowledge base?
Options:
automatic knowledge acquisition
simpler tools
discovery of new concepts
all of the mentioned
Answer: D
Question: _________________ type of phishing became very popular as if it has been sent from a legitimate source with a legitimate link to its official website.
Options:
Algo-based phishing
Email-based phishing
Domain Phishing
Vishing
Answer: B
Question: The samples of the moisture test are prepared in _______ heater bulb.
Options:
Infrared
X-ray
Radio
Ultraviolet
Answer: A
Question: Which of the following global option has value “hide”?
Options:
results
fig.width
echo
none of the mentioned
Answer: A
Question: A superincreasing knapsack problem is ____ to solve than a jumbled knapsack.
Options:
Easier
Tougher
Shorter
Lengthier
Answer: B
Question: Which of the following is correct?
Options:
In steady flow, pathlines and streamlines are identical
In steady flow, pathlines and streaklines are identical
In steady flow, streaklines and streamlines are identical
In steady flow, pathline, streamlines and streaklines are all identical
Answer: C
Question: _______ is part of user documentation.
Options:
Class diagram
Use case
Code comment
Installation guide
Answer: A
Question: Find the coefficient of x7 in (x+4)9.
Options:
523001
428700
327640
129024
Answer: D
Question: How does the Hardware trigger an interrupt?
Options:
Sending signals to CPU through a system bus
Executing a special program called interrupt program
Executing a special program called system program
Executing a special operation called system call
Answer: A
Question: Which of the following is Edman reagent?
Options:
Phenylisothiocyanate
CF3 COOH
FDNB
Phenylthiocarbonyl
Answer: A
Question: The slave (which is selected) sends the vector on data bus after the
Options:
first INTA (active low) pulse from 80286
second INTA (active low) pulse from 80286
third INTA (active low) pulse from 80286
none of the mentioned
Answer: B
Question: The sulphur content in acid-cupola operation does not depend on which of the following factors?
Options:
Quantity of coke
Slag basicity
Tensile strength of the steel
Quantity of steel
Answer: C
Question: In trusses, a member in the state of tension is subjected to:-
Options:
push
pull
lateral force
either pull or push
Answer: B
Question: Which of the tolerance values are obtained, when we use cut and peel mask method for maskant?
Options:
± 0.013 mm
± 0.045 mm
± 0.077 mm
± 0.179 mm
Answer: D
Question: What will be the tension in cable DE?
Options:
106.12
206.12
306.12
406.12
Answer: B
Question: Power delivered to load is _________ with an increase in harmonic distortion.
Options:
Increases
Decreases
Constant
Cannot predict
Answer: A
Question: Consider the languages L1 = and L2 = {a}. Which one of the following represents L1 L2* U L1*?
Options:
€
a*
All of the mentioned
None of the mentioned
Answer: A
Question: Which of the following is conceptually similar to objects?
Options:
PACKAGE
PROC
PRIVATE
None of the mentioned
Answer: A
Question: When the ratio of r/z equals to 2, the Boussinesq influence factor is ________ of the maximum.
Options:
23%
57%
17.7%
1.8%
Answer: D
Question: The base register is also known as the ____________
Options:
basic register
regular register
relocation register
delocation register
Answer: C
Question: 19 mm thick fibre panels with thermal conductivity of 0.12 W/m.K are used for false ceiling of an AC room. If the floor area of the room is 17.65 m^2 and the temperature difference across the fibre panel is 15°C, calculate the heat transfer rate.
Options:
4.672 kW
3.672 kW
2.672 kW
1.672 kW
Answer: C
Question: What is capacity of a network?
Options:
number of inputs it can take
number of output it can deliver
number of patterns that can be stored
none of the mentioned
Answer: B
Question: Why is climbing a lamp post harder than climbing up a tree?
Options:
Because of parallel friction force
Because of contact force between the bodies
Because of Van der Wall’s force
Because of rope force
Answer: A
Question: What are the three popular semantic modes?
Options:
Unix, Coherent & Session semantics
Unix, Transaction & Session semantics
Coherent, Transaction & Session semantics
Session, Coherent semantics
Answer: B
Question: If L1 is regular L2 is unknown but L1-L2 is regular ,then L2 must be
Options:
Empty set
CFG
Decidable
Regular
Answer: D
Question: Why retardation test is carried on DC machine?
Options:
To find stray losses
To find eddy current losses
To find field copper losses
To find windage losses
Answer: A
Question: Which of the brakes are effective on a bicycle?
Options:
Small ones
Bigger ones
Both small and big
Neither small nor big
Answer: C
Question: Which of the following process ensures that versions of systems and components are recorded and maintained?
Options:
Codeline
Configuration control
Version
Workspace
Answer: B
Question: Which of the following are true?
Options:
Cold working reduces toughness and ductility
Cold worked components have poor resistance to shocks and vibrations
Tooling for cold working is cheaper as compared to hot working
All of the mentioned
Answer: A
Question: What are the best anti knocking reagents of petrol?
Options:
straight chain alkanes
straight chain alkenes
alkynes
aromatics
Answer: D
Question: Which model assumes that systems are created from reusable components, scripting or database programming?
Options:
An application-composition model
A post-architecture model
A reuse model
An early design model
Answer: C
Question: Who developed the first learning machine in which connection strengths could be adapted automatically?
Options:
McCulloch-pitts
Marvin Minsky
Hopfield
none of the mentioned
Answer: C
Question: Soft metal lubricants are produced by using ____________
Options:
purifying
thermal spraying
distillation
electroplating
Answer: B
Question: _________ of a beam is a measure of its resistance against deflection.
Options:
Strength
Stiffness
Deflection
Slope
Answer: B
Question: An entity in A is associated with at most one entity in B, and an entity in B is associated with at most one entity in A.This is called as
Options:
One-to-many
One-to-one
Many-to-many
Many-to-one
Answer: B
Question: The engine cylinder of a reciprocating steam engine is produced using casting operation. The casting of the cylinder consists of two chamber, namely _____
Options:
Steam chamber and condensing chamber
Cylinder chamber and valve chamber
Top chamber and bottom chamber
back chamber and front chamber
Answer: B
Question: The volumetric efficiency ____ when carried out in stages.
Options:
decreases
increases
remains constant
none of the mentioned
Answer: B
Question: Which of the following is the characteristics of a normal cell?
Options:
Anchorage independent
Continuous cell lines
Dependent on external growth factor
No contact inhibition
Answer: C
Question: Which of the following is not applicable for IP?
Options:
Error reporting
Handle addressing conventions
Datagram format
Packet handling conventions
Answer: A
Question: The Kinetic energy of a photoelectron emitted on shining a light of wavelength 6.2 X 10-6 m on a metal surface of work function 0.1 eV is _________________
Options:
0.01 eV
0.02 eV
0.1 eV
1 eV
Answer: B
Question: The bull block is used in which of the following metal working process?
Options:
Extrusion
Impact extrusion
Indirect extrusion
Wire drawing
Answer: B
Question: How many bit positions are active and can affect L[0, 0] in the Iota step function?
Options:
8
12
6
7
Answer: D
Question: Find \(lt_{x\rightarrow 0}\frac{2cos(2x)+3cos(5x)-5cos(19x)}{cos(4x)-cos(3x)}\)
Options:
-76
-6
-7
0
Answer: A
Question: Processing of mRNA includes __________
Options:
5′ capping, 3′ polyadenylation and RNA splicing
3′ capping, 5′ polyadenylation and RNA splicing
5′ capping and 3′ polyadenylation
5′ capping and RNA splicing
Answer: A
Question: 10. Aliasing is caused when:
Options:
Sampling frequency must be equal to the message signal
Sampling frequency must be greater to the message signal
Sampling frequency must be less to the message signal
Sampling frequency must be greater than or equal to the message signal
Answer: C
Question: Which one is a FALSE statement?
Options:
There exists a unique DFA for every regular language
NFA can always are converted to a PDA
Complement of CFL is always recursive
Every NDFA can be converted to a DFA
Answer: D
Question: An arch is a beam except for ____
Options:
It does not resist inclined load
It does not resist transverse forces
It does not allow rotation at any point
It does not allow horizontal movement
Answer: D
Question: Which among the following on chlorination undergoes substitution at the alkyl group?
Options:
Ethers
Hydroxyl groups
Carbonyl compounds
Carboxylic acids
Answer: B
Question: Thevenin’s equivalent circuit consists of a ____________
Options:
Voltage source in series with a resistor
Current source in parallel with a resistor
Voltage source in parallel with a resistor
Current source in series with a resistor
Answer: A
Question: High angle grain boundary will have ________________ and low angle grain boundary will have _______________
Options:
higher surface energy, low surface energy
low surface energy, Higher surface energy
higher surface energy, Higher surface energy
low surface energy, Low surface energy
Answer: B
Question: Selection of a football team for FIFA World Cup is called as?
Options:
random sampling
systematic sampling
purposive sampling
cluster sampling
Answer: D
Question: In a clapp oscillator with three capacitor C1, C2, C3, C1 is used as upper capacitor in voltage divider, C2 is used as lower capacitor in voltage divider and C3 is the third capacitor. For perfect operation which of these capacitor should have minimum value?
Options:
C1
C2
C3
All of them are equal
Answer: C
Question: 4. What does the following piece of code do?<div class="hk1_style-wrap4"><div class="hk1_style-wrap3"><div class="hk1_style-wrap2"><div class="hk1_style-wrap"><div class="hk1_style"><div class="java"><pre class="de1"><span class="kw1">public</span> <span class="kw4">void</span> func<span class="br0">(</span>Tree root<span class="br0">)</span> <span class="br0">{</span> func<span class="br0">(</span>root.<span class="me1">left</span><span class="br0">(</span><span class="br0">)</span><span class="br0">)</span><span class="sy0">;</span> func<span class="br0">(</span>root.<span class="me1">right</span><span class="br0">(</span><span class="br0">)</span><span class="br0">)</span><span class="sy0">;</span> <span class="kw3">System</span>.<span class="me1">out</span>.<span class="me1">println</span><span class="br0">(</span>root.<span class="me1">data</span><span class="br0">(</span><span class="br0">)</span><span class="br0">)</span><span class="sy0">;</span> <span class="br0">}</span></pre></div></div></div></div></div></div>
Options:
Preorder traversal
Inorder traversal
Postorder traversal
Level order traversal
Answer: A
Question: A block of material of specific gravity 0.45 floats in water. Determine the meta-centric height of the block if its size is 3 m * 2 m* 0.8 m.
Options:
0.506 m
0.376 m
1.012 m
0.127 m
Answer: B
Question: The Mg2+ ion in restriction endonuclease is not bound to ________
Options:
Water molecule
Carboxylates of the enzymes aspertate group
Oxygen
Histidine
Answer: D
Question: A steam turbine inlet is at 1200 kPa, 500°C. The actual exit is at 300 kPa, 300°C with an actual work of 407 kJ/kg. What is its reversible work output if ambient temperature is at 25°C?
Options:
414.9 kJ/kg
314.9 kJ/kg
214.9 kJ/kg
614.9 kJ/kg
Answer: D
Question: The address lines multiplexing is done using ______
Options:
MMU
Memory controller unit
Page table
Overlay generator
Answer: B
Question: 6. What is the commercial use of silica gel?
Options:
Removal of organic pollutants from aqueous effluents
Production of N2 from air
Drying of air and other gases
Separation of molecules based on size and shape
Answer: C
Question: Which among the following is problem caused by geothermal plant?
Options:
Land usage
Noise pollution
Global warming
Greenhouse effect
Answer: B
Question: A rectangular channel has cross sectional area of 50 m2. If the channel section is to be most economical calculate the depth. Take B = 10m.
Options:
10 m
5 m
8 m
12 m
Answer: B
Question: CNT is ___________
Options:
Conductor
Insulator
Semi conductor
Impure metal
Answer: C
Question: Which region of the transistor is highly doped?
Options:
Emitter
Base
Collector
Both Emitter and Collector
Answer: A
Question: Which of the following is applied in one or more stages where each stage is a series of three equally spaced parallel grids?
Options:
Ionisation field
Reflection
RF field
Acceleration
Answer: C
Question: Which command concatenate the specified argument into a single command, then execute the command?
Options:
fc
eval
exec
getopts
Answer: B
Question: Which one is the excess reactant?
Options:
Cl2
C4H8
C4H7Cl
None of the mentioned
Answer: B
Question: 6. What will be the output of the following Python code?<div class="hk1_style-wrap4"><div class="hk1_style-wrap3"><div class="hk1_style-wrap2"><div class="hk1_style-wrap"><div class="hk1_style"><div class="python"><pre class="de1">sentence <span class="sy0">=</span> <span class="st0">'we are humans'</span> matched <span class="sy0">=</span> <span class="kw3">re</span>.<span class="me1">match</span><span class="br0">(</span>r<span class="st0">'(.*) (.*?) (.*)'</span><span class="sy0">,</span> sentence<span class="br0">)</span> <span class="kw1">print</span><span class="br0">(</span>matched.<span class="me1">group</span><span class="br0">(</span><span class="br0">)</span><span class="br0">)</span></pre></div></div></div></div></div></div>
Options:
(‘we’, ‘are’, ‘humans’)
(we, are, humans)
(‘we’, ‘humans’)
‘we are humans’
Answer: D
Question: The transcription bubble formed for facilitating RNA synthesis is about _____________ nucleotides long.
Options:
10
17
14
20
Answer: B
Question: When frequency of oscillation of circuit is less than series resonance frequency wS crystal oscillator act as __________
Options:
Inductor
Capacitor
Resistor
Transistor
Answer: B
Question: The mode of transmission of data, where one bit is sent for each clock cycle is ______
Options:
Asynchronous
Parallel
Serial
Isochronous
Answer: D
Question: While conducting lab experiments on DC machine loading, the students are given a machine with its rating as 100 kW maximum rating. Then the _____________
Options:
machine can’t be overloaded after 100 kW
machine can be overloaded after 100 kW
machine can be overloaded by 5% for a small time duration
machine can be overloaded by 10%
Answer: A
Question: Which regression test selection technique exposes faults caused by modifications?
Options:
Efficiency
Precision
Generality
Inclusiveness
Answer: C
Question: The formula for the pumping out test in an unconfined aquifer is given by _________
Options:
\(k=\frac{qπ}{1.36(H^2-h^2)}log_{10}\frac{R}{r} \)
\(k=\frac{q}{1.36(H^2-h^2)}log_{10}\frac{R}{r} \)
\(k=\frac{q}{π(H^2-h^2)}log_{10}\frac{R}{r} \)
\(k=\frac{q}{1.36(H^2-h^2)} \)
Answer: B
Question: The switching of power with a NPN transistor is called_________
Options:
sourcing current
sinking current
forward sourcing
reverse sinking
Answer: B
Question: If a structure has total 10 joints, then what should be the minimum no. of joints in which equilibrium equations should be concurrently satisfied for stability?
Options:
7
8
9
10
Answer: B
Question: Which of the following statement is correct to check the violation of hold time?
Options:
IF(clk’DELAYED(hold_time)’EVENT) THEN
IF(clk’DELAYED(hold_time) = ‘1’) THEN
IF(clk’DELAYED(hold_time) = ‘0’) THEN
IF(clk’DELAYED(hold_time) = ‘1’ AND clk’DELAYED(hold_time)’EVENT) THEN
Answer: D
Question: 1. What is the output of this program?<div class="hk1_style-wrap4"><div class="hk1_style-wrap3"><div class="hk1_style-wrap2"><div class="hk1_style-wrap"><div class="hk1_style"><div class="c"><ol><li class="li1"><pre class="de1"> <span class="co2">#include&lt;stdio.h&gt;</span></pre></li><li class="li1"><pre class="de1">&nbsp;</pre></li><li class="li1"><pre class="de1"> <span class="kw4">int</span> main<span class="br0">(</span><span class="br0">)</span></pre></li><li class="li1"><pre class="de1"> <span class="br0">{</span></pre></li><li class="li1"><pre class="de1"> <span class="kw4">int</span> fd_socket<span class="sy0">;</span></pre></li><li class="li1"><pre class="de1"> fd_socket <span class="sy0">=</span> socket<span class="br0">(</span>AF_UNIX<span class="sy0">,</span>SOCK_STREAM<span class="sy0">,</span><span class="nu0">0</span><span class="br0">)</span><span class="sy0">;</span></pre></li><li class="li1"><pre class="de1"> <span class="kw3">printf</span><span class="br0">(</span><span class="st0">"%d<span class="es1">\n</span>"</span><span class="sy0">,</span>fd_socket<span class="br0">)</span><span class="sy0">;</span></pre></li><li class="li1"><pre class="de1"> <span class="kw1">return</span> <span class="nu0">0</span><span class="sy0">;</span></pre></li><li class="li1"><pre class="de1"> <span class="br0">}</span></pre></li></ol></div></div></div></div></div></div>
Options:
-1
0
any integer value
none of the mentioned
Answer: D
Question: For exothermic reactions, which condition is applicable for equilibrium constant K?
Options:
K decreases with increasing temperature
K decreases with decreasing temperature
Positive ΔH°rxn with increasing temperature; K increases
Negative ΔH°rxn with increasing temperature; K increases
Answer: C
Question: Cloud computing doesn’t require that ________ and software be composable.
Options:
cloud
database
hardware
all of the mentioned
Answer: C